0
I C O M CS-207
OPERATING GUIDE (for IC-207H)
GETTING STARTED
p Before using the program, make a backup copy of
the original disk. Operate the program using the
#A ba ckup and keep the original in a safe p/ace.
This cloning program is designed to perform data
setting and cloning for the dual band transceiver
IC-207H.
I
I
To use this program, the following hardware and
software are required:
l
IBM PC/AT or PS/2 compatible computer with an
RS-232C serial port
l MS-DOS, PC-DOS or IBM DOS ver. 5.02 or higher
. OPC-646 CLONING CABLE
CONNECTIONS
cloning operations are performed from
computer’s keyboard including power ON only connect to a DC power supply is needed
r the transceiver.
I
DB9 female plug
(incl. level converter circuit)
\
IC-207H
Personal
computer
-646 Cloning cable
be purchased separately)
INSTALLATION AND PROGRAM START UP
n Installation and initial setup’
n Starting the program
Connect the transceiver and PC as above then connect a DC power supply to the the transceiver.
To start the program after installation, operate as
follows at the DOS prompt:
To install the CS-207 cloning software to
ICOM\CS207 directory of drive C while the program
disk is in drive A, type as follows at the DOS prompt:
@) Change to the installed directory.
l
A:\INSTALL A: C:\ICOM\CS207 [Enter]
T Program drive ‘7” Target drive/directory
0 Select the connected RS-232C (COMlKOM2)
port with the [ t]/[ $1 and [Enter] keys.
@ Input your call sign then push [Enter].
@ After the initial setup, CS-207 is automatically
launched. Set or modify the data as desired.
l
CS207 [Enter] (at the installed directory)
I
A target directory is created if it does not already
exist; CS-207 cannot be installed to the root directory.
After the installation is finished, the CS-207 initial
setup screen appears and the transceiver model is
checked. Proceed as follows:
See the back page for operation.
@>‘fie the File sub menu to save the data or to exit
the program.
C:\ICOM\CS207 in case of the example at left.
@ Type as follows to start:
n
Operating from a floppy disk
This program can be operated from a floppy disk.
0
@
@
@
Insert the backup disk into the floppy disk drive.
Select the floppy disk drive as the current drive.
Select the “CS207” directory.
Type “CS207,” then push [Enter] to start.
7
NEVER remove the program disk from the floppy disk
drive while the program is running.
NEVER set the floppy disk as write-protected.
Cloning will take 20 sec. or more when operating from a
1 floppy disk.
Portions of this software are copyrighted by Microsoft Corporation.
MS-DOS is a Microsoft trademark.
.~
,.-..--I”,, m-,.-F m-.- - - - - -
MENU FLOW
Push [Alt] or [Esc] to select the TOP menu.
The TOP menu lightens,
; screens and operations can be selected from the TOP menu.
Push [Fl] to call up the help message.
l
l
To select a SUB menu, push
the highlighted key; or select
with the [d]/[c] keys then
push [Enter] or [ 4 1.
The screen darkens when the TOP
menu is selected.
SUB MENU
File
Screen
Clone
Print
Setup
Load
Save
Delete
DOS
Preset
Exit
Memory CH
VFO
DTMF Autodial
Common
Read (- TR
Write -) TR
Information
Current
All
Display Type
Wallpaper
RS-232C
Call Sign
,
Load
Loads data from a saved file.
Save
Saves data to a desired file. File
extension (.ICF) is added automatically.
Delete
Deletes a file.
Allows you to use a DOS command. To
return to the previous screen, type
“EXIT” then push [Enter].
Loads a preset file. Moves the cursor
to the first memory channel for input in
the V or U memory channel screen.
g DOS
Preset
c
VFO
z
$j D
T M F
Autodial
C ommon
- _
Ic.nm Inr
Read (- TR
2
2 Write -) TR
0
CH
Sets the operating frequency, duplex
setting, etc. for call, memory and scan
edge channels.
Sets the operating frequency, duplex
setting, etc. for VFO.
Sets the DTMF codes, DTMF
transmission speed, etc.
Sets commonly used data, such as set
mode settings, initial set mode settings,
cloning comments, etc.
Reads clone data from a connected
transceiver.
Sends clone data to a connected
transceiver.
Shows the connected transceiver model
and clone comment.
Current
Prints out currently displayed screen
data.
AII
Prints out all set data.
Display Type
Selects the display type from color l/2
and monochrome. Customized colors
can be used.
-g
p
DESCRIPTION
Information
Quits and exits the program, then
returns to the DOS prompt.
Exit
Memory
SUB MENU
DESCRIPTION
3 Wallpaper
z
Selects the wallpaper. This can be
previewed before selection,
RS- 232C
Selects one of the computer’s RS232C
ports for cloning connection.
Call Sian
Enters your call sign.
Open as PDF
Similar pages