P.O. Box 27
4300 AA Zierikzee
The Netherlands
Tel. +31 111 413656
Fax. +31 111 416919
www.deltapowersupplies.com
DELTA ELEKTRONIKA B.V.
A mating connector
with faston tabs is
packed with each
power supply
SX - SERIES
EURO CASSETTE SWITCHED MODE POWER SUPPLIES
With autoranging input for worldwide use
The SX - series covers the whole output voltage range between
3.5 V and 400 V DC.
Models
Voltage range
Current range
75 SX 5
150 SX 5
75 SX 15 -15
150 SX 15 -15
150 SX 75 - 75
150 SX 200 - 200
3.5 - 6 V
3.5 - 6 V
2 x 6 - 15 V
2 x 6 - 15 V
2 x 15 - 75 V
2 x 35 - 200 V
13 A
26 A
2.5 A
5A
1A
0.3 A
30V
15
SERIES MODE
PARALLEL MODE
0
0
2
4
6
8
10
12A
150SX15-15
For 24 V
For 24 V
For 75SX15-15 optional 2x 6-18 V 2 A is possible
2.5 A use 75SX15-15
5 A use 150SX15-15
For 24 V redundant parallel operation
use 240S24 instead of 150SX15-15.
The units with two equal outputs can be used in three
different modes, series-, parallel- and dual-mode,
simply by connecting the outputs in series or parallel
at the mating connector.
The two outputs cannot be used separately.
+
+ 15V
10A
+
+
+ 30V
5A
+
0
Parallel mode
+
+ 15V
5A
+
- 15V
5A
0
Series mode
150SX15-15
Dual mode
DELTA ELEKTRONIKA BV
SX-Series
Index of possible voltage / current combinations
Voltage range
Max. current Model
3.5
3.5
6
6
12
12
15
30
35
70
-
6V
6V
15 V
15 V
30 V
30 V
75 V
150 V
200 V
400 V
13
26
5
10
2.5
5
2
1
0.6
0.3
A
A
A
A
A
A
A
A
A
A
75SX5
150SX5
75SX15-15
150SX15-15
75SX15-15
+
+
+
+
– 6 to 15 V
– 6 to 15 V
– 15 to 75 V
– 35 to 200 V
2.5
5
1
0.3
A
A
A
A
75SX15-15
150SX15-15
150SX75-75
150SX200-200
and
and
and
and
Derating of output current at low line voltage
150SX15-15
150SX75-75
150SX75-75
150SX200-200
150SX200-200
Specifications:
Input
single phase, 48-62 Hz
:
Power derating vs input
Pout max @ 110V AC
Pout max @ 125V AC
Pout max @ 210V AC
Pout max @ 225V AC
Input current
Internal fuses
:
:
:
:
:
:
Autoranging
98 - 132 V AC or 185 - 264 V AC,
for DC or operation at 400 Hz contact factory.
75SX5/15
150SX5/15/75
150SX200-200
50 W
100 W
100W
75 W
150 W
120W
50 W
100 W
100W
75 W
150 W
120W
1.3Arms
2.6Arms
2.6Arms
2AT
4AT
4AT
Inrush current limit
Insulation
Input / output
Input / case
Output / case
:
10 A with NTC resistor 30 Ohms, cold resistance.
:
:
:
Safety
EMC
:
:
Efficiency
:
Voltage regulation
Load 0 - 100%
Line 225 - 264 V AC
Ripple + noise
Stability
Temp. coefficient
Output impedance
:
:
:
:
:
:
:
Recovery time
:
4 kVrms (1 min.), 8 mm creepage/cl.
2.5 kVrms (1 min.), 5 mm creepage/cl.
500 V DC, 1 mm creepage/clearance
1 kV DC for 150SX75-75 and 150SX200-200.
EN 60950 EN 61010
EN 61204-3
Power Supply Standard
EN 61000-6-3
(EN 55022B) Generic Emission
EN 61000-6-2
Generic Immunity
84 % dual units, 80 % 5V units at 230 V AC input.
81 % and 78 % respectively at 110 V AC input.
5 and 15 V models
75 and 200 V models
10 mV (with ext.sense)
200 mV
10 mV
150 mV
5 mVrms, max. 20 mVp-p
70 mVrms, 100 mV p-p (BW = 20 MHz)
5.10–4 during 8 hours under constant conditions after 1 hr warm up.
1.10–4 per °C
%
Max. 0.1 Ohm up to 100 kHz, except
100
150SX75-75 and 150SX200-200 max. 1 Ohm.
Output
0.1 ms to recover to within 0.1 V after a
current
50
50-100% load step. Max. deviation 0.4 V.
0.6 ms / 1.2 V for 75 V and 200 V models.
Ambient temperature
Storage
Operating
Temp. protection
Hold-up time
Series operation
Parallel operation
Redundant par. operation
:
:
:
:
:
:
:
Page 1 - 2
Transformer with split bobbin
provides 4 kV dielectric strength
between input and output.
Vertical mounting
Horizontal mounting
Ambient temp.
-20
0
20
40
60
80 C
−40 to + 85 °C
−20 to + 50 °C, derate current linearly to 20% from 50 to 75 °C.
Temperature derating
Overtemperature protected.
15 ms at full load, 30 ms at half load (230 V AC).
Up to 500 V total voltage. Up to 1 kV for 150SX75-75 and 150SX200-200.
Allowed up to 40 °C ambient temperature
Is possible with external diodes
SPECIFICATIONS
Rev. Sept. 2015
SX-Series
DELTA ELEKTRONIKA BV
Current limit
Voltage limit
Voltage adjustment
Remote control
Remote programming
Remote sensing
Remote ShutDown
Led lamp
MTBF
Dim. and weight
: The current limit is fixed and protects the power supply during overload and short circuit.
Continuous overload and short circuit does not harm the unit.
10% more current can be taken at the low end of the voltage range.
: For safety a second regulation circuit limits the output voltage to about 10% above its
range in case the normal regulation loop fails.
: The output voltage is continuously variable over the whole range with a 20 turn screwdriver adjustment through the front panel.
: Voltage control with an external potentiometer is possible after some small internal
changes (see manual page 3-2).
: Remote programming of the output voltage is possible after changing an internal link on
the PCB. An analog voltage of 5 V between PROG. and S– corresponds with the max output voltage. Note: In dual mode S– is at a negative polarity.
: The sense points are internally connected to + and – output. These links have to be removed when remote sensing is required. The max. sense range is 2 V per load lead for
SX15-15 and 0.5 V for SX5. However the voltage across the leads plus the load cannot
exceed the supply max. output rating.
150SX75-75 and 200-200 have no remote sensing facility.
: By +5 V (3.5 - 12 V) between RSD and S– or –. Note: In dual mode S– is at neg.polarity.
: A green led lamp at the front panel indicates the output.
: 1 000 000 hrs
: 75SX h x w x d = 100 x 35.5 x 172 mm, 0.6 kg
150SX h x w x d = 233.4 x 35.5 x 172 mm, 1.2 kg
75SX15-15 or 150SX15-15 used as dual power supply
Because the sense points of the regulation are internally connected to the + and –15 V terminals, the total voltage V1 + V2 is
kept constant.
When V1 and V2 are equally loaded the zero point will be in the
middle.
With unequal loads a slight zero shift will occur.
Asymmetrical overloading and shortcircuiting will not
damage the unit.
The 150SX75-75 and 150SX200-200 have similar
characteristics (relatively better).
Zero-shift caused by unequal loading of the + and – 15 V
The sense points S+ and S– are
internally connected to + and –.
If remote sensing is required the
internal links have to be removed
(not allowed at 75 V and 200 V).
75SX5
use 2 pins
parallel
150SX5
use 3 pins
parallel
Units with two equal outputs:
Parallel mode
Series mode
Dual mode
Connections SX-series
Bench adapters
BA 150
BA 150 can be used with:
150SX15-15, 240S24,
other 150SX optional
75SX5
75SX15-15
150SX5
150SX15-15
150SX75-75
150SX200-200
The H15 mating connector (DIN 41612) is standard
available with faston tabs, and optional with screw terminals or solder pins
Rev. Sept. 2015
SPECIFICATIONS
BA 75 can be used with:
75SX5
75SX15-15
Page 1 - 3
DELTA ELEKTRONIKA BV
SX-Series
Eurocard rack mounting
Wall and rail mounting 75 SX
F8-3
for
75SX
F8-6 for 150SX
Vertical wall mounting with W8-3 and CL15
Mounting kit H95 for flat
wall mounting
Rail mounting with
W8-3, AR1 and CL15
Flat wall mounting with H95 kit and CL15
Dimensions acc. to DIN 41494 to fit
into Eurocard racks 3U height
(132.5 mm) or 6U height (265 mm)
Adapters
Wall and rail mounting 150 SX
Vertical wall mounting with W8-6 and CL15
W8-3 for vertical
wall or rail
mounting 75SX
W8-6 for vertical
wall or rail
mounting 150SX
Clamp CL15 to fix the H15
connector when wall
mounted
Adapter AR1 for
35 mm
rail mounting
Page 1 - 4
Bracket H155 for flat
wall mounting
SPECIFICATIONS
Rail mounting with
W8-6, AR1 and CL15
Flat wall mounting with 2 pcs H155 and CL15
Rev. Sept. 2015
Open as PDF
Similar pages