Eberspacher timer EasyStart T Operating

www.butlertechnik.com
EasyStart T
Operating instructions.
Comfort Timer
with 7-day preset capability.
www.butlertechnik.com
www.butlertechnik.com
Contents
Introduction
• Please read first ..................................................................................................... 3
• Safety information .................................................................................................. 3
• General information ................................................................................................ 3
• Purpose ................................................................................................................. 3
Overview
• Timer ..................................................................................................................... 4
• Displays ................................................................................................................. 5
Operation and Adjustment
• Basic operation and adjustment rules..................................................................... 6
• Activate timer ......................................................................................................... 7
•
Set weekday, time and operating time .............................................................. 8
•
Switch on heater................................................................................................ 9
•
Switch off heater.............................................................................................. 10
•
Switch on ventilation ........................................................................................ 11
•
Switch off ventilation ........................................................................................ 12
•
General notes on ”ventilate“ mode ................................................................... 13
•
Switch on add-on unit...................................................................................... 14
•
Switch off add-on unit...................................................................................... 15
•
General information on the add-on unit ............................................................ 15
•
General information on programming the preset time....................................... 16
•
Program preset times ................................................................................ 17, 18
•
Delete preset times .......................................................................................... 19
•
Set heating level – of water heaters.................................................................. 20
•
Set heating level – of air heaters....................................................................... 21
What to do if …?
• Displays ......................................................................................................... 22, 23
• Preset time not programmable / Display disappears............................................. 23
Service
• Hotline ................................................................................................................. 24
2
www.butlertechnik.com
www.butlertechnik.com
Important Information
Please read first
General information
Please ensure you read through these
operating instructions carefully before you
start to set and use the timer.
These operating instructions contain
important information, which you require
to set and use the timer.
Please store these operating instructions
in a safe place so you can refer to them at
a later date.
The timer has a simple control structure.
With only 4 keys, it is possible to set all
functions, change them if necessary and
program the preset times.
We recommend use of the temperature
sensor, available as an option, in order to
be able to utilise all the timer’s functions.
If a vehicle was disconnected from the
power supply (battery disconnected) and
the power supply is reinstated, the time
appears when the timer is activated. This
must then be adjusted. See description on page 8 “Set weekday, time and
operating time”.
Operation of the timer is described in
detail from page 6.
Safety information
Danger!
– All information and notes, in particular
the safety information in the heater’s
technical description must be observed
at all times!
– The heater must be switched off when
refuelling.
– Only use original spare parts.
Purpose
The EasyStart T timer is used to switch
on / off and preset the switching on time,
operating time and operating mode of the
heater and / or add-on unit installed in
the vehicle.
Please note!
Improper use and use outside the specified area of use cancels all liability and
warranty.
www.butlertechnik.com
3
www.butlertechnik.com
Overview
Timer
The timer can be used to make the
settings and adjustments necessary for
operation of the heater and to switch
various units on and off.
Please note!
The number of symbols and displays
differs depending on the installed heater
and feature options.
Display bar
Menu bar
Program bar
Display of the active
program memory
and corresponding
weekday
Control key –
Next
Control key –
Back
Select a function in
the menu bar and
adjust values
Select a function in
the menu bar and
adjust values
Activation key
OK key
• Timer – ON / OFF
• Switch over in the display bar
between
– Temperature
– Time
– Operating time
– Temperature setpoint value
• Switch back to the
menu bar
Select the flashing
symbol or confirm
inputs
Covering cap and
fixing screw
Status display
4
www.butlertechnik.com
www.butlertechnik.com
Overview
Displays
Menu bar
Display bar
Heater ON / OFF
Numerical and text displays
Ventilation ON / OFF
AM Time in the morning (English)
Add-on unit ON / OFF
PM Time in the afternoon (English)
Program preset time
°C
Temperature in degrees Celsius
Set the time / operating time
F
Temperature in degrees Fahrenheit
Set heating level
Unlimited operating time
Heating level set
Program bar
Status display
Preset memory 1
Heating mode active
Preset memory 2
Ventilation mode active
Preset memory 3
Add-on unit active
Mo – So
Weekdays
Mo – Su
English weekdays
Please note!
• If the program number is underlined,
e.g.
this program will be executed
next.
• “Ventilate” mode
is not possible in all
heater models.
• The add-on unit function
is not possible with all heater models and must be
activated by the installation workshop.
www.butlertechnik.com
5
www.butlertechnik.com
Operation and Adjustment
Basic operation and adjustment rules
Activate timer
or no setting or actuation is made, the
If the display is not lit, the timer must be
activated before each use.
display disappears within 10 seconds, i.e.
the timer switches to idle state.
For renewed input you must press
The timer must be activated before each
again.
operation or adjustment.
To do this, press
until the menu bar
key and continue with the operation or
Set operating time
(one-off or permanent)
adjustment (see also page 7).
The operating time can be individually set
appears in the display, then release the
with
minutes or continuous operation
in the menu, program
confirmed with
.
.
See pages 8, 9, 11 and 14 for a descrip-
and display bar can be
or
.
In immediate operation from 10 – 120
Each flashing symbol
changed with
or
In preset mode from 10 – 120 minutes.
Flashing symbols
tion.
and
Confirm input
Display if a temperature sensor is
connected.
Settings and changes must always be
If the optional tempera-
confirmed with
ture sensor is connected
, otherwise they are lost
the time and temperature
(exception: operating time).
can be alternately disTerminate / quit settings
played by pressing
You can use
In the settings and ope-
to terminate or quit ente-
.
rations described below
ring settings in a menu.
it is assumed that a temperature sensor is
connected.
Display disappears
If the vehicle lighting is switched off, no
heater or additional unit is switched on,
6
www.butlertechnik.com
www.butlertechnik.com
Operation and Adjustment
Activate timer
Display
press until the menu bar appears in the display and
the temperature is displayed.
The timer is activated.
Please note!
• Possible displays such as
and
are described
in the chapter “What to do if …?” from page 22.
• If the heater or additional unit is in use or the vehicle
lighting is switch on (terminal 58), the timer does not
have to be activated.
The following actions are possible:
• Switch from temperature display to time and back,
press
.
• Select functions in the menu bar with
confirm selection with
or
,
.
The further procedure is described in the relevant
section for the selected function.
www.butlertechnik.com
7
www.butlertechnik.com
Operation and Adjustment
Set weekday, time and operating time
Activate timer with
(see page 7).
Display
Select symbol
with
or
Confirm selection with
Select weekday with
or
Confirm selection with
Set hours with
or
.
.
or
Confirm setting with
.
.
Confirm setting with
Set minutes with
.
.
.
.
Permanently set operating time for immediate operation
with
or
.
Confirm setting with
.
The adjustment is completed.
The following action is possible:
• Select functions in the menu bar with
selection with
or
, confirm
.
The further procedure is described in the relevant
section for the selected function.
8
www.butlertechnik.com
www.butlertechnik.com
Operation and Adjustment
Switch on heater
Activate timer with
(see page 7).
Display
Select symbol
with
Confirm selection with
or
.
.
Heater is switched on.
The following actions are possible for the operating
time:
• The operating time can be accepted with
.
• The operating time can be changed as a one-off with
or
and then confirmed with
.
Please note!
The operating time last displayed is adopted without
confirmation.
•
press to display the temperature, the last saved
operating time remains valid.
The following actions are possible:
• Call up display.
press, the current heating level is displayed
(for air heaters only)
press to display the time.
press to display the operating time.
See above for adjustment.
• Select functions in the menu bar with
confirm selection with
or
,
.
The further procedure is described in the relevant section for the selected function.
www.butlertechnik.com
9
www.butlertechnik.com
Operation and Adjustment
Switch off heater
Display
Select symbol
with
Confirm selection with
or
.
.
Heater is switched off.
The following actions are possible:
• Switch from temperature display to time and back,
press
.
• Select functions in the menu bar with
selection with
or
, confirm
.
The further procedure is described in the relevant
section for the selected function.
10
www.butlertechnik.com
www.butlertechnik.com
Operation and Adjustment
Switch on ventilation – only possible if
symbol is displayed
in the menu bar (for general information, see page 13).
Activate timer with
(see page 7).
Display
Select symbol
with
Confirm selection with
or
.
.
Ventilation is switched on.
The following actions are possible for the operating
time:
• The operating time can be accepted with
.
• The operating time can be changed as a one-off with
or
and then confirmed with
.
Please note!
The operating time last displayed is adopted without
confirmation.
•
press to display the temperature, the last saved
operating time remains valid.
The following actions are possible:
• Call up display.
press to display the time.
press to display the operating time.
See above for adjustment.
• Select functions in the menu bar with
confirm selection with
or
,
.
The further procedure is described in the relevant
section for the selected function.
www.butlertechnik.com
11
www.butlertechnik.com
Operation and Adjustment
Switch off ventilation– only possible if
symbol is displayed
in the menu bar (for general information, see page 13).
Display
Select symbol
with
Confirm selection with
or
.
.
Ventilation is switched off.
The following actions are possible:
• Switch from temperature display to time and back,
press
.
• Select functions in the menu bar with
confirm selection with
or
,
.
The further procedure is described in the relevant
section for the selected function.
12
www.butlertechnik.com
www.butlertechnik.com
Operation and Adjustment
General notes on ”ventilat“ mode
If the symbol
is not displayed in the
menu bar, „ventilate“ mode is only possible in the heater for the heater models
under certain prerequisites:
• With the water heaters HYDRONIC
(B / D 4 W S, B / D 5 W S,
B / D 4 W SC and B / D 5 W SC): the
“heat / ventilate” switch (Order No. 22
1000 31 89 00) must be installed.
• With the air heaters AIRTRONIC /
AIRTRONIC M: the mini controller
(Order No. 22 1000 32 07 00) must be
installed.
Please note!
“Ventilate” mode is not provided for
upgraded independent heaters.
Select „ventilate“ or „heat“ for the
heater models listed above and
switch on.
Use the “heat / ventilate” switch or the
mini controller to select “ventilate” or
“heat” mode and then switch on the
heater with the timer.
After the heater has been switched off in
“ventilate” mode, you can immediately
switch to “heat” mode using the “heat /
ventilate” switch or the “mini controller”.
Then use the timer to switch the heater
back on.
Switch of “ventilate” or “heat” mode
Use the timer to switch off the heater (see
page 12 resp. 10).
Please note!
• “Ventilate” or “heat” mode must be
selected before switching on the
heater.
• In the “ventilate” switch setting of
HYDRONIC water heaters the vehicle
blower is directly controlled by bypassing heat mode and in AIRTRONIC air
heaters the heater’s blower is bypassed
in the same way.
• If you have any further questions regarding “ventilate” mode please contact
your installation workshop or call the
service phone number (see page 24).
Switching between “ventilate” and
“heat” mode
If you switch mode while “ventilate” or
“heat” is running, you must use the timer
to switch of the heater (see page 12 and
10).
If the heater is switched off in “heat”
mode the heater runs on. Once this afterrun has ended use the “heat / ventilate”
switch or the “mini controller” to switch to
“ventilate” mode. Then use the timer to
switch the heater back on.
www.butlertechnik.com
13
www.butlertechnik.com
Operation and Adjustment
Switch on add-on unit – only possible if
symbol is displayed
in the menu bar (for general information, see page 15 ).
Activate timer with
(see page 7).
Display
Select symbol
with
Confirm selection with
or
.
.
Add-on unit is switched on.
The following actions are possible for the operating
time:
• The operating time can be accepted with
.
• The operating time can be changed as a one-off with
or
and then confirmed with
.
Please note!
The operating time last displayed is adopted without
confirmation.
•
press to display the temperature, the last saved
operating time remains valid.
The following actions are possible:
• Call up display.
press to display the time.
press to display the operating time.
See above for adjustment.
• Select functions in the menu bar with
confirm selection with
or
,
.
The further procedure is described in the relevant
section for the selected function.
14
www.butlertechnik.com
www.butlertechnik.com
Operation and Adjustment
Switch off add-on unit– only possible if
symbol is displayed
in the menu bar.
Display
Select symbol
with
Confirm selection with
or
.
.
Add-on unit is switched off.
The following actions are possible:
• Switch from temperature display to time and back,
press
.
• Select functions in the menu bar with
confirm selection with
or
,
.
The further procedure is described in the relevant
section for the selected function.
General information on the add-on unit
An add-on unit can be e.g. a second
heater or parking air conditioning.
It is also possible to combine a heater
with a blower. The blower is used to circulate air within the inside of the vehicle.
The heaters or blower can be operated
simultaneously or independently of each
other.
The “add-on unit” function must be activated by the workshop.
www.butlertechnik.com
15
www.butlertechnik.com
Operation and Adjustment
General information on programming the preset time
The timer can be used to program 3
preset times.
The 3 preset times can either all be
spread over one weekday or be spread
between different weekdays.
In water heaters and if a temperature
sensor is connected to the timer the
heater start is automatically calculated depending on the measured room
temperature and the selected heating
level (ECO or HIGH). The operating
time can be between 5 and 60 minutes
before the programmed departure time,
whereby operation is always stopped 5
minutes after the programmed departure
time. Therefore, the minimum possible
operating time is 10 minutes and the max
possible operating time is 65 minutes.
In this case, the operating time set in the
“set time” menu (page 8) is ineffective.
In all other configurations the start takes
place according to the preset operating
time.
Please note!
• The preselected times are always
departure times, even if runtime calculation is deactivated.
• You cannot program more than 3 preselection times.
• The maximum operating time of 65 minutes for automatic runtime calculation
is a factory setting. If necessary, this can
be reduced by the installation workshop
to a minimum of 15 minutes.
16
Identical preset times
If several identical preset times are
programmed for a specific weekday in
programs 1, 2 or 3 the last entered preset
time is valid. When the timer is activated, the identical preset times saved are
deleted.
If identical preset times are programmed
for different weekdays there is not conflict.
Overlapping of preset times
Example:
You have set the “Heater” operating mode
on a weekday for your departure time at
13 hrs. At the same time the ”Ventilation“
mode has been programmed for the
same day for 12.45 hrs and with an operating time of 15 minutes. What happens?
The timer calculates the start of heating
for the ”heater“ mode which, depending
on the ambient temperature measured
can lie between 5 and 60 minutes before
the programmed departure time. If the
calculated heater start is after 12.45 hrs,
the vehicle is ventilated between
12.30 hrs and 12.45 hrs and is then
heated.
If the calculated heater start is before
12.45 hrs, the vehicle is heated until
12.30 hrs, then the heater is stopped and
the heater switches to “ventilation” mode.
After the set “ventilation” mode operating
time has expire the heater switches off.
www.butlertechnik.com
www.butlertechnik.com
Operation and Adjustment
Program preset times
Activate timer with
(see page 7).
Display
Select symbol
with
Confirm selection with
or
.
.
Select preset memory 1, 2 or 3 with
with
Select weekday Mo – Su with
with
or
and confirm
.
or
and confirm
.
Set hours with
or
Set minutes with
and confirm with
or
and confirm with
Select the required function
confirm with
.
,
or
with
.
or
and
.
Continued on page 18
www.butlertechnik.com
17
www.butlertechnik.com
Operation and Adjustment
Program preset times
Display
The operating time is only displayed if
deactivated runtime calculation),
and can be accepted with
and confirmed with
(heat with
or
is selected
or adjusted with
or
.
The adjustment is completed.
Please note!
The assigned preset memory locations
appear in the display. The next preset memory to be activated is underlined in the
display and the corresponding weekday is
also displayed.
The same procedure is required to program preset times in the preset memory
2 and 3.
The following actions are possible:
• Switch from temperature display to time and back,
press
.
• Select functions in the menu bar with
confirm selection with
or
,
.
The further procedure is described in the relevant
section for the selected function.
18
www.butlertechnik.com
www.butlertechnik.com
Operation and Adjustment
Delete preset times
The steps for deleting preset times are the same as
for adjusting / setting the preset time, until the current
Display
function flashes in the status bar.
or press
until
Confirm with
.
appears in the display.
The preset time is deleted.
The following actions are possible:
• Switch from temperature display to time and back,
press
.
• Select functions in the menu bar with
confirm selection with
or
,
.
The further procedure is described in the relevant
section for the selected function.
www.butlertechnik.com
19
www.butlertechnik.com
Operation and Adjustment
Set heating level – of water heaters
In water heaters you can choose between the
ECO heating level (normal heating) and HIGH
(comfort heating).
The selected heating level is required to calculate
the “heat” operating time depending on the
measured ambient temperature.
Please note!
The heating levels ECO and HIGH are only effective in conjunction with a programmed preset time.
Activate timer with
(see page 7).
Display
Select symbol
with
Confirm selection with
or
.
.
Select ECO or HIGH heating level with
confirm with
or
and
.
The selected heating level (e.g. HIGH) is set.
20
www.butlertechnik.com
www.butlertechnik.com
Operation and Adjustment
Set heating level – of air heaters
Air heaters can be individually set to a heating level of 8
to 36 in immediate and preset mode.
Please note!
Heating levels 8 to 36 only approximately correspond to
a temperature reading and therefore may differ from the
actual temperature in the vehicle.
Activate timer with
(see page 7).
Anzeige im Display
Select symbol
with
Confirm selection with
or
.
.
Change the heating level with
confirm with
or
and
.
The new heating level is set.
www.butlertechnik.com
21
www.butlertechnik.com
What to do if …?
Displays
Description
Remedy
A fault occurs in the heater during operation (e.g. fuel shortage or interruption in
the diagnostics cable).
See heater’s installation instructions for
troubleshooting advice.
Description
Automatic hardware detection is currently active.
Possible cause
Remedy
Timer has been disconnected from the
voltage and reconnected.
Wait until the automatic hardware detection has finished.
Description
The ”Set timer“ display appears after the timer is activated.
Possible cause
Remedy
The timer’s power supply was interrupted. All programmed preset times have
been deleted.
Set time (see page 8).
(only for combinations of 2 controls EasyStart T / T, R+ / T, R / T)
Description
No communication between the controls.
Possible cause
Remedy
Overlapping during data transfer
Repeat operator action.
22
www.butlertechnik.com
www.butlertechnik.com
What to do if …?
Anzeigen
(only for combinations of 2 controls EasyStart R+ / T, R / T )
Description
Radio remote control is in teach mode.
Possible cause
Remedy
Timer has been disconnected from the
voltage and reconnected..
Wait until teach mode has ended.
Preset time cannot be programmed / display disappears
It is not possible to program a preset time.
Possible cause
ADR mode is active. It is not permitted to program preset times in this mode
( is not available in the menu bar).
Display disappears.
Possible cause
Remedy
Terminal 58 (lighting) not connected.
Connect terminal 58 (lighting).
Please note!
If you are unable to remedy the fault
or error, please contact an authorised
JE workshop or dial the service phone
number given on page 24.
www.butlertechnik.com
23
www.butlertechnik.com
Service
Hotline
If you have any technical question, a
problem with your timer or the heater, dial
the following service phone number:
Telephone hotline
Phone 0800 / 12 34 300
Fax hotline
Fax 01805 / 26 26 24
Outside of Germany, please contact the
respective national Eberspächer service
agent.
24
www.butlertechnik.com
www.butlertechnik.com
www.butlertechnik.com
www.butlertechnik.com
www.butlertechnik.com
www.butlertechnik.com
www.butlertechnik.com
J. Eberspächer
GmbH & Co. KG
Eberspächerstraße 24
D-73730 Esslingen
Telefon 0711 939-00
Telefax 0711 939-0643
info@eberspaecher.com
www.butlertechnik.com
22 1000 32 88 06
07.2006
www.eberspaecher.com
We reserve the right to make changes
Printed in Germany
© J. Eberspächer GmbH & Co. KG
www.butlertechnik.com
Open as PDF
Similar pages