2017 Nissan Murano | Quick Reference Guide

QUICK REFERENCE GUIDE
MURANO
2017
2580654_17b_Murano_US_pQRG_091616.indd 2
9/16/16 1:16 PM
2580654_17b_Murano_US_pQRG_091616.indd 3
4
5
3
6
16
7
1
8
2
9
10
17
11
18
Behind
12 steering
wheel
13
1
2
3
9/16/16 1:16 PM
4
5
6
14
19
15
Instrument Brightness
Control Switch*
Twin Trip Odometer Switch*
Headlight and Turn
Signal Switch
Low Tire Pressure Warning Light
Vehicle Information Display
Wiper and Washer Switch
*See your Owner’s Manual for information.
20
Steering Wheel Switches for
Audio*/Bluetooth®/Navigation/
Vehicle Information Display
Cruise
Control/
8
Intelligent Cruise Control
9 Heated Steering Wheel Switch*
Vehicle Dynamic Control (VDC)
10
OFF Switch
7
11 Liftgate/Liftgate Release Switch*
12 Tilt/Telescopic Steering Column*
13 Fuel-filler Door Release Handle
14 Hood Release*
15 Power Rear Flip-up Seats Switch
16 Control Panel Display*/
Audio System
21
17 Heater and Air
Conditioner (automatic)
18 Front Passenger Air Bag
Indicator Light*
19 Push-button Ignition Switch
Climate-controlled
Seat Switches*
21 Power Outlet 12V/120W
20
TABLE OF CONTENTS
NEW SYSTEM FEATURES
How to Use Your Murano’s Touch-screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Heated Steering Wheel (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Around View® Monitor (AVM) with Moving Object Detection (MOD) (if so equipped) . 3
Blind Spot Warning (BSW) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Forward Emergency Braking (FEB) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Predictive Forward Collision Warning (PFCW) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . 6
Vehicle Dynamic Control (VDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hill Start Assist (HSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SiriusXM Travel Link and SiriusXM Traffic (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Siri® Eyes Free (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ESSENTIAL INFORMATION
Tire Pressure Monitoring System (TPMS) with Easy-Fill Tire Alert . . . . . . . . . . . . . . . . . . . . . 8
Loose Fuel Cap and Fuel-filler Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Towing Your Vehicle (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Clock Set/Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FIRST DRIVE FEATURES
Nissan Intelligent Key® System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power Liftgate Release (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Front Seat Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Automatic Drive Positioner (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Starting/Stopping the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Rear Seat Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Outside Mirror Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Headlight Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wiper and Washer Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Heater and Air Conditioner (automatic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FM/AM/SiriusXM® Satellite Radio with CD Player and Navigation . . . . . . . . . . . . . . . . . . . 20
USB (Universal Serial Bus) Connection Port/iPod® Interface and AUX Jack . . . . . . . . . 22
Cruise Control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Intelligent Cruise Control (ICC) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Front Armrest/Center Console Storage Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SYSTEM GUIDE
Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Hands-free Text Messaging Assistant (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
NissanConnectSM Services Powered by SiriusXM® (if so equipped) . . . . . . . . . . . . . . . . . . . 27
Apple CarplayTM (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Bluetooth® Hands-free Phone System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
System Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Bluetooth® System with Navigation (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Bluetooth® System without Navigation (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Bluetooth® Streaming Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
HomeLink® Universal Transceiver (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Additional information about your vehicle is also available in your Owner’s Manual,
Navigation System Owner’s Manual and at www.NissanUSA.com.
Please see your Owner’s Manual for important safety information and system operation limitations.
•A cellular telephone should not be used for any purpose while driving so full attention may
be given to vehicle operation.
• Always wear your seat belt.
• Supplemental air bags do not replace proper seat belt usage.
•Children 12 and under should always ride in the rear seat properly secured in child
restraints or seat belts according to their age and weight.
• Do not drink and drive.
For more information, refer to the “Safety — Seats, seat belts and supplemental restraint system
(section 1)”, the “Display screen, heater, air conditioner, audio and phone systems (section 4)”
and the “Starting and driving (section 5)” of your Owner’s Manual.
2580654_17b_Murano_US_pQRG_091616.indd 4
9/16/16 1:16 PM
NEW SYSTEM FEATURES
5
2
3
3
1
4
6
HOW TO USE YOUR MURANO’S
TOUCH-SCREEN DISPLAY
1 Launch Bar – Various functions can be
accessed by touching the items on the
Launch Bar 1 , which is displayed on most
of the main screens. Touching these keys will
bring up the corresponding screens.
7
2 Widget – These items can be interchanged,
moved or deleted from the MENU pages.
3 Touch either arrow to navigate to the next or
8
previous page of the “MENU” screen.
4 These dots indicate the page you are
currently on, in white, out of the number of
pages there are available, in gray.
5 Shortcut – Shortcuts, once touched, will bring
up the system they correspond to for quick,
one-touch convenience for commonly
used features.
Shortcuts and Widgets can be set up through
the “Edit Menu” screen which can be accessed
by touching the
“Settings” key 6 followed
by the “Edit Home Menu” key 7 . This will
display the “Edit Menu” screen, which allows
Shortcuts and Widgets to be moved and
rearranged 8 , deleted 9 or created 10 .
9
10
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
For more information, refer to your Navigation System
Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2
2580654_17b_Murano_US_pQRG_091616.indd 2
9/16/16 1:16 PM
HEATED STEERING WHEEL (if so equipped)
Once activated, your heated steering wheel
will automatically turn on and off to maintain
a temperature above 68°F (20°C).
When the surface temperature of the steering
1
wheel is above 68°F (20°C) and the heated
steering wheel switch 1 is turned on, the
system will not heat the steering wheel. This does not indicate a malfunction.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
AROUND VIEW® MONITOR (AVM) WITH MOVING OBJECT
DETECTION (MOD) (if so equipped)
1
With the ignition switch in the ON position,
the Around View® Monitor is activated by
pressing the CAMERA button 1 , located on
the control panel, or by moving the shift lever
to the R (REVERSE) position. The monitor
displays various views of the position of
the vehicle.
When the shift lever is in the P (PARK), N (NEUTRAL) or D (DRIVE) position and
the CAMERA button 1 is pressed, the following views will display in order:
Start from any Control Panel screen
Front view & bird’s-eye view
Press
Front view & front-side view
Press
Press
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 3
3
9/16/16 1:16 PM
NEW SYSTEM FEATURES
When the shift lever is in the R (REVERSE) position and the CAMERA button 1
is pressed, the following views will display in order:
Rear view & bird’s-eye view
Rear view & front-side view
Press
Press
The colored guide lines on the display screen indicate vehicle width and
approximate distances to objects with reference to the vehicle body line.
• Red 1.5 ft (0.5 m); Yellow 3 ft (1 m); Green 7 ft (2 m) and 10 ft (3 m).
For information regarding how to access additional viewing cycles,
please see your Owner’s Manual.
There are some areas where the system will not detect objects.
• When in the front or the rear view display, an
object below the bumper or on the ground
may not be detected 2 .
2
• When in the bird’s-eye view, a tall object near
the seams of the camera detecting areas 3
will not appear in the monitor.
• The distance between objects viewed on the
Around View Monitor differs from the
actual distance.
Objects in the bird’s-eye view will appear
further than the actual distance.
MOVING OBJECT DETECTION (MOD)
3
The MOD system helps inform the driver of
moving objects in the Around View Monitor.
The system will operate when the shift lever is in the P (PARK), N (NEUTRAL), or
R (REVERSE) position and the vehicle is driven at speeds of approximately
5 mph (8 km/h) or less.
If the MOD system detects moving objects, a yellow frame will be displayed on
the camera image and a chime will sound.
4
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 4
9/16/16 1:16 PM
When the following is displayed:
• Blue MOD icon 4 ; the system is active.
• Gray MOD icon; the system is not active.
• No MOD icon; the system is off. The indicator
will also be off if all of the warning systems
are deactivated using the Settings menu.
The MOD system will not operate if the
liftgate is open.
4
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Display screen, heater, air conditioner, audio and phone systems
(section 4)” of your Owner’s Manual.
BLIND SPOT WARNING (BSW) (if so equipped)
The BSW system helps to alert the driver
when another vehicle moves into the
vehicle’s detection zone.
An indicator light located near the outside
mirrors 1 will illuminate if the radar sensors
detect a vehicle in the detection zone.
The indicator light 2 will illuminate after the ignition switch
is ON and the BSW system is enabled. This indicates that the
BSW system is operational.
1
2
Please see your Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
FORWARD EMERGENCY BRAKING (FEB) (if so equipped)
The FEB system can assist the driver when there is a risk of a forward collision
with a vehicle in the traveling lane.
The FEB operates at speeds greater than 3 mph (5 km/h).
If a risk of a forward collision is detected, the FEB system will provide an initial
warning to the driver by both a visual and audible alert. If the driver applies the
brakes quickly and forcefully after the warning and the FEB system detects that
there is still the possibility of a forward collision, the system will automatically
increase the braking force. If the driver does not take action, the FEB system
issues the second warning and also applies partial braking. If the risk of a
collision becomes imminent, the FEB system applies harder
braking automatically.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 5
5
9/16/16 1:16 PM
NEW SYSTEM FEATURES
PREDICTIVE FORWARD COLLISION WARNING (PFCW)
(if so equipped)
The PFCW system can help alert the driver of sudden braking by a second
vehicle traveling ahead of the vehicle in the same lane.
If there is a potential risk, the PFCW will warn the driver with a blinking vehicle
ahead detection indicator and an audible warning tone will be heard.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
VEHICLE DYNAMIC CONTROL (VDC)
Always make sure the VDC is on by ensuring the VDC OFF
light, located in the meter gauges, is not on before driving
the vehicle.
The VDC OFF switch 1 should only be used briefly to help free
the vehicle if it is stuck in snow or mud.
1
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” and the “Starting and driving
(section 5)” of your Owner’s Manual.
HILL START ASSIST (HSA)
The HSA system allows time for the driver to release the brake pedal and apply the
accelerator when the vehicle is parked on a hill. The brakes are applied automatically
for 2 seconds after the driver releases the brake pedal.
The HSA system will operate automatically under these conditions:
• The shift lever is shifted into a forward or a reverse gear.
• The vehicle is stopped completely on a hill by applying the brake.
The HSA system will not operate when the shift lever is in the N (NEUTRAL) or
P (PARK) position or when the vehicle is on a flat and level road.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
6
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 6
9/16/16 1:16 PM
SiriusXM TRAVEL LINK AND SiriusXM TRAFFIC
(if so equipped)
Your vehicle’s Navigation System is equipped
with SiriusXM Travel Link and SiriusXM
Traffic capabilities.
Touch the “Info” key to access SiriusXM
Travel Link and SiriusXM Traffic.
SiriusXM Travel Link provides access to
real-time weather information and forecasts,
nearby fuel prices, movie listings, sports
scores and stock quotes.
SiriusXM Traffic provides information that
may help to avoid delays due to traffic
incidents. Traffic jams, roadwork, road
closures around the current location, etc.,
are represented graphically on the map by
icons depicting the nature of the event. Incidents on the route are automatically
displayed as they are approached.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Information (section 5)” and the “Navigation (section 6)” of your
Navigation System Owner’s Manual.
SIRI® EYES FREE (if so equipped)
If you have a compatible iPhone®, with Siri®,
you can link your iPhone® to the Siri® Eyes
Free function in your vehicle’s
Bluetooth® system.
If you have a compatible iPhone® connected
to the system, press and hold the
button
1 on the steering wheel for a few seconds
and Siri® will be activated in Eyes Free mode.
1
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating
and feature information.
For more information, refer to the “Display screen, heater, air
conditioner, audio and phone systems (section 4)” of your
Owner’s Manual and visit www.NissanUSA.com/bluetooth.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 7
7
9/16/16 1:16 PM
ESSENTIAL INFORMATION
TIRE PRESSURE MONITORING SYSTEM (TPMS) WITH
EASY-FILL TIRE ALERT
A Tire Pressure Low Add Air warning
message will appear in the vehicle
information display 1 and the low tire
pressure warning light 2 will illuminate
when one or more tires are low in pressure
and air is needed.
• The tire pressures should be checked when the tires are cold.
The tires are considered cold after the vehicle has been parked
for 3 hours or more or driven less than 1 mi (1.6 km) at
moderate speeds.
1
2
After tire pressures are adjusted, drive the vehicle at speeds above 16 mph
(25 km/h). The Tire Pressure Low Add Air warning message and low tire
pressure warning light 2 will extinguish.
In addition to the Tire Pressure Low Add Air warning message, you can view
the individual tire’s pressure in the vehicle information display as well as the
recommended pressure, denoted by blue lettering, for each tire.
When adding air to an under-inflated tire, the TPMS with Easy-Fill Tire
Alert provides visual and audible signals to help you inflate the tire to the
recommended COLD tire pressure.
To use the Easy-Fill Tire Alert:
1.Move the shift lever to the P (PARK) position and apply the
parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3.Add air to the under-inflated tire, and within a few seconds, the hazard
warning lights will start flashing.
4.When the designated tire pressure is reached, the horn will beep once and the
hazard warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.
When the low tire pressure warning light 2 flashes for 1 minute and then
remains on, the TPMS is not functioning properly. Have the system checked. It is
recommended you visit a Nissan dealer for this service.
Tire pressure rises and falls depending on the heat caused by the vehicle’s
operation and the outside temperature. Low outside temperature can lower
the temperature of the air inside the tire, which can cause a lower tire inflation
pressure. This may cause the low tire pressure warning light 2 to illuminate.
If the warning light illuminates, check the tire pressure in your tires.
8
• Check the tire pressure (including the spare tire) often and always prior to long
distance trips.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 8
9/16/16 1:16 PM
The Tire and Loading Information label contains valuable information. Please
refer to the “Technical and consumer information (section 10)” of your Owner’s
Manual for the location of the Tire and Loading Information label.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving
(section 5)” and the “Do-it-yourself (section 8)” of your Owner’s Manual.
LOOSE FUEL CAP AND FUEL-FILLER DOOR
LOOSE FUEL CAP
A LOOSE FUEL CAP warning message will
appear in the vehicle information display 1
when the fuel-filler cap is not
tightened correctly.
To tighten, turn the cap clockwise until a
single click is heard.
If the cap is not properly tightened, the
Malfunction Indicator Light
may illuminate.
1
FUEL-FILLER DOOR
To open the fuel-filler door, pull the release
handle 1 , located on the instrument
panel to the left of the steering wheel.
1
The fuel-filler door is located on the driver’s
side of the vehicle.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” and the “Pre-driving checks
and adjustments (section 3)” of your Owner’s Manual.
TOWING YOUR VEHICLE (if so equipped)
ALL-WHEEL DRIVE (AWD) VEHICLE
An all-wheel drive vehicle must be towed with all wheels off the ground.
For proper towing and to avoid accidental damage to your vehicle, NISSAN
recommends that a service operator tow your vehicle after carefully reading the
Owner’s Manual precautions.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “In case of emergency (section 6)” and the “Technical and consumer
information (section 10)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 9
9
9/16/16 1:17 PM
ESSENTIAL INFORMATION
CLOCK SET/ADJUSTMENT
SYSTEM WITHOUT NAVIGATION
To adjust the time and the appearance of the
clock on the display:
1. Press the SETTING button 1 .
2. Scroll by turning the TUNE/SCROLL
knob 2 .
3. Select “Clock Adjust”.
2
1
To adjust the minutes and hours, press the SETTING button 1 to select the
item and use the TUNE/SCROLL knob 2 to adjust the time.
SYSTEM WITH NAVIGATION
To adjust the time and the appearance of the
clock on the display:
MENU button on the
1. P
ress the
control panel.
2. Touch the
“Settings” key on the
Launch Bar.
3. Touch the “Clock” key.
The following settings can be adjusted:
•O
n-screen Clock: The clock in the upper right corner of the display can be turned
ON or OFF.
• Clock Format (24h): The clock can be set to 12 hours or 24 hours.
•O
ffset (hour): The time can be adjusted by increasing or decreasing per hour.
•O
ffset (min): The time can be adjusted by increasing or decreasing per minute.
•D
aylight Savings Time: The application of Daylight Savings Time can be turned
ON or OFF.
•T
ime Zone: Adjust the time zone. Choose a time zone from the available list.
Touch the
key or press the
BACK button to return to the previous screen.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Display screen, heater, air conditioner, audio and phone systems
(section 4)” of your Owner’s Manual or the “Getting started (section 2)” of your Navigation System
Owner’s Manual.
10
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 10
9/16/16 1:17 PM
FIRST DRIVE FEATURES
NISSAN INTELLIGENT KEY® SYSTEM
The Nissan Intelligent Key® system allows you to lock or unlock your vehicle, open
your liftgate (if so equipped) and start the engine (if so equipped). It is important to
make sure the Intelligent Key (I-Key) is with you (that is, in your pocket or purse).
KEY-LINKED SYSTEM (if so equipped)
The vehicle information display has added features, allowing the Key-Linked
System to remember some of the vehicle information display settings.
The Key-Linked System states which I-Key is
being recognized 1 , and enabling/disabling
of the system’s function can be easily
accessed through notifications on the
vehicle information display.
The Key-Linked System can be turned on or
off through the vehicle information display
“Settings” screen 2 .
You can set a maximum of four I-Keys to the
Key-Linked System.
When the system is enabled, the recognized
I-Key is displayed at engine start-up (engine
ON) as well as within the vehicle information
display “Settings” screen 2 .
When the system is active, the vehicle
information display setting items are memorized for each key that has been
enabled in the Key-Linked System.
If two keys are in the vehicle, the Key-Linked System will recognize the key that
was used most recently; this usually means the last key to unlock/lock the door
from the I-Key.
If there is a desire to change to another key that is in the vehicle, the user must
turn off the engine and initiate communication from the desired key.
1
2
1. Turn the engine to OFF.
2. Press the
3. Start the engine.
4. The desired Key Number recognized should appear on the vehicle
information display.
button from the desired I-Key.
The vehicle information display displays a pop-up notification at engine ON for
the recognition of the system with a shortcut function to the setup menu.
From the shortcut setup menu, users can select to enable or disable the KeyLinked System or select “Later” to keep the factory state.
When enabled, the Key-Linked System will remember the state of the items
memorized automatically from the last ignition cycle.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 11
11
9/16/16 1:17 PM
FIRST DRIVE FEATURES
REMOTE ENGINE START* (if so equipped)
The remote start operating range is approximately 200 ft (60 m) from the
vehicle. The effective operating range may be shorter if there are walls, strong
radio wave sources near the operating location or other obstructions between
the key and the vehicle.
For the remote start to function, the vehicle must be in the P (PARK) position
with the ignition off and all doors must be closed and locked.
Please see your Owner’s Manual for additional information.
To start your vehicle remotely:
1. Press the button 4 to lock all doors.
2. Within 5 seconds, press and hold the engine start
3 for at least 2 seconds.
3
4
button
6
The engine will start, and the parking lights will turn on.
The automatic climate control system will begin heating
or cooling the vehicle depending on the outside (ambient)
temperature, cabin (in-car) temperature and the last user
mode. During this period, the climate control display and buttons will be
inoperable until the ignition switch is turned ON.
The engine will run for 10 minutes and then turn off.
Repeat steps 1 and 2 to extend the time for an additional 10-minute period.
Remote start can only be activated for a maximum of 20 minutes.
7
• After two remote starts, the ignition switch must be cycled before the remote
start can be used again.
• To cancel the remote start, press the remote start
button 3 .
To start driving, depress the brake pedal and press the ignition switch
START/STOP button.
LOCKING AND UNLOCKING THE VEHICLE
The operating range of the I-Key is within
31.5 in (80 cm) from each request switch.
To lock the vehicle, either push the door
handle request switch 5 once or press the
button 4 on the key fob.
5
To unlock the vehicle, perform one of the
following procedures:
• Push either door handle request switch 5 once to unlock the corresponding
door. Push the door handle request switch 5 again within 1 minute to unlock
all doors, or
• Press the button 6 on the key fob to unlock the driver’s side door. Press the
button 6 again within 1 minute to unlock all doors.
12
The I-Key can also be used to activate the panic alarm by pressing and holding
the button 7 for 1 second. Once activated, the panic alarm and headlights
will stay on for a period of time.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 12
9/16/16 1:17 PM
NISSAN INTELLIGENT KEY® BATTERY DISCHARGE
If the battery of the I-Key is discharged or environmental conditions interfere
with the I-Key operation, Key Battery Low 8 will display on the gauge and the
engine will need to be started according to
8
the following procedure:
Key Battery Low
1. M
ove the shift lever to the
P (PARK) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the I-Key. A chime will sound.
4. Within 10 seconds after the chime sounds, press the ignition switch
START/STOP button while depressing the brake pedal and the engine
will start.
*State laws may apply; review local laws before using.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)”, the “Pre-driving checks and
adjustments (section 3)”, the “Starting and driving (section 5)” and the “Do-it-yourself (section 8)” of
your Owner’s Manual.
POWER LIFTGATE RELEASE (if so equipped)
Use one of the following methods to open the liftgate:
Press the
for 1 second.
Push the liftgate opener switch 2 on the
exterior of the vehicle while carrying the
Intelligent Key with you (that is, in your pocket
or purse).
From inside the vehicle, push the power
liftgate switch 3 , located on the instrument
panel to the left of the steering wheel.
button 1 on the Nissan Intelligent Key®
1
3
Please see your Owner’s Manual for important
safety information, system limitations, and
additional operating and feature information.
For more information, refer to the “Pre-driving
checks and adjustments (section 3)” of your
Owner’s Manual.
2
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 13
13
9/16/16 1:17 PM
FIRST DRIVE FEATURES
FRONT SEAT ADJUSTMENTS
POWER SEATS (if so equipped)
To slide the seat forward or backward, push
the
switch 1 forward or backward.
To recline the seatback, push the
switch 2 forward or backward.
2
1
3
POWER SEAT LIFTER (driver’s seat)
To adjust the angle of the front seat cushion
or height of the seat, push the front or rear
end of the
switch 1 up or down.
2
1
LUMBAR SUPPORT (if so equipped for driver’s seat)
To adjust the seat lumbar support, push the front or back end of
the
switch 3 .
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Safety — Seats, seat belts and supplemental restraint system
(section 1)” of your Owner’s Manual.
AUTOMATIC DRIVE POSITIONER (if so equipped)
Automatic Drive Positioner provides two
methods for storing the driver’s seat, steering
column (if so equipped) and outside mirror
positions. Once enabled, the Key-Linked
System automatically retains the driver’s
last positions for the specific Intelligent Key
when the ignition switch is turned from ON
to OFF. The Automatic Drive Positioner switch
can store two additional positions which are
independent from the Key-Linked System.
1
2
KEY-LINKED SYSTEM
Follow the process below to set up
Key-Linked System:
•U
nlock the vehicle with the desired
Intelligent Key while the ignition
switch is in the OFF position.
lace the ignition switch in the ON position.
•P
• In the vehicle information display,
navigate to the Settings menu and select
“Key-Linked Settings” 1 .
• In the Key-Linked Settings menu, press the
OK button on the steering wheel to turn
the system ON or OFF 2 .
14
5
4
3
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 14
9/16/16 1:17 PM
Once the system is on, the driver’s seat, the outside mirror and the steering
column (if so equipped) positions are linked to the Intelligent Key every time
when the ignition is turned from ON to OFF.
Follow the same procedure if you want to link a 2nd, 3rd or 4th Intelligent Key.
AUTOMATIC DRIVE POSITIONER SWITCHES
In addition to the Key-Linked System feature, two additional driver preferences
can be saved using the memory switches 1 3 and 2 4 .
Follow this procedure to set the memory positions:
• Place the ignition switch to the ON or ACC position. The vehicle should be
stopped while setting the memory.
• Adjust the driver’s seat, steering column (if so equipped) and outside mirrors to
the desired positions using the adjustment switches for each feature.
• Push the SET switch 5 , and within 5 seconds, push the memory
switch 1 3 or 2 4 .
• The indicator light for the selected switch will illuminate for 5 seconds and a
chime will sound indicating the memory has been successfully stored.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” and the “Pre-driving checks
and adjustments (section 3)” of your Owner’s Manual.
STARTING/STOPPING THE ENGINE
It is important to make sure the Nissan
Intelligent Key® is with you (that is, in your
pocket or purse).
Depress the brake pedal.
Press the ignition switch START/STOP
button to start the engine.
TURNING THE ENGINE OFF
Move the shift lever to the P (PARK) position.
Press the ignition switch START/STOP button to turn the engine off.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 15
15
9/16/16 1:17 PM
FIRST DRIVE FEATURES
REAR SEAT ADJUSTMENTS
FOLDING DOWN THE REAR SEAT
To fold the seats flat, release the connector
tongue of the rear center seat belt from the
buckle then store the connector and seat
belt tongues in the retractor base on
the ceiling 1 .
Fold the seatback forward using either the
reclining strap 2 , located on the outside
edge of the rear seat, or the release lever 3
in the cargo area.
1
2
4
To raise the seatback manually, lift up each
seatback and push it to the upright position
until it is latched.
To raise the seatback automatically (if so equipped), push and
hold the power seatback switch 4 located in the cargo area
or the corresponding seat switch 5 on the lower side of the
instrument panel.
3
5
•A
beep sounds once and the seatback begins to move automatically.
•A
beep sounds twice when the seatback is fully returned to the upright
seating position.
RECLINING THE REAR SEATS
Brace the back of the seat with your arm while pulling on the strap.
The seatback will release quickly.
Pull the reclining strap 2 , and move the seatback to the desired angle.
Release the reclining strap 2 after positioning the seat at the desired angle.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Safety – Seats, seat belts and supplemental restraint system
(section 1)” of your Owner’s Manual.
OUTSIDE MIRROR CONTROL SWITCH
To select the right or left side mirror, slide the
control switch 1 right or left.
To adjust the mirror angle, move the control
switch 2 up, down, right or left.
To prevent accidentally moving the mirror,
slide the switch to the center
(neutral) position.
2
1
REVERSE TILT-DOWN FEATURE (if so equipped)
The reverse tilt-down feature will turn both outside mirror surfaces downward to
provide better rear visibility close to the vehicle.
16
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 16
9/16/16 1:17 PM
1. Apply the brake.
2. Place the ignition switch in the ON position.
3. Move the shift lever to the R (REVERSE) position.
4. Both outside mirror surfaces will turn downward. (The mirror control switch 1
must be out of the center [neutral] position.)
The outside mirror surfaces will return to their original positions when one of the
following conditions has occurred:
The shift lever is moved to any position other than R (REVERSE).
The outside mirror control switch is set to the center (neutral) position.
The ignition switch is placed in the OFF position.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
HEADLIGHT CONTROL SWITCH
HEADLIGHT CONTROL
Turn the headlight control switch to the
position 1 to turn on the front parking,
side marker, tail, license plate and instrument
panel lights. Turn the switch to the
position 2 to turn on the headlights.
3
1
2
AUTOLIGHT SYSTEM
The autolight system will automatically turn the headlights on when it is dark
and off when it is light. The system will keep the headlights on for a period of
time after you turn the ignition off and all doors are closed.
To activate the autolight system, turn the headlight control switch to the AUTO
position 3 then push the ignition switch to ON. To deactivate the autolight
system, turn the headlight control switch to the OFF position,
position 1
or
position 2 .
HIGH BEAM SELECT
With the headlights ON (either by selecting
the AUTO position 3 or
position 2
4
), push the headlight control switch forward
5
4 to select the high beam function. The
blue indicator light
will illuminate in the
instrument panel. Pull the headlight switch back to the original position to select
the low beam. The blue indicator light will extinguish.
Pull and release the headlight control switch 5 to flash the headlight high
beams on and off.
FOG LIGHT SWITCH (if so equipped)
The headlights must be on and the low beams
to operate.
selected for the fog lights
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 17
17
9/16/16 1:17 PM
FIRST DRIVE FEATURES
Turn the switch (inside collar) to the
Turn the switch (inside collar) to the OFF position to turn the fog lights off.
position 6 to turn the fog lights on.
LANE CHANGE SIGNAL
Move the lever up or down until the turn signal begins to flash but the lever does
not latch to signal a lane change. Hold the
lever until the lane change is completed.
Move the lever up or down until the turn
signal begins to flash but the lever does not
latch and release the lever. The turn signal
will automatically flash three times.
6
Choose the appropriate method to signal a lane
change based on the road and traffic conditions.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
WIPER AND WASHER SWITCH
Move the lever to one of the following
positions to operate the windshield wipers:
3
MIST
OFF
1 Mist (MIST) – One sweep operation of the
2 Intermittent (INT) – Front wipers operate
4 Low (LO) – Front wipers operate at a
5 High (HI) – Front wipers operate at a
6 Pull the lever toward you to activate the
continuous low-speed.
4
LO
intermittently, and the speed can be
adjusted by twisting the time control ring
3 to increase or decrease wiper speed.
2
INT
front wipers.
1
5
HI
6
9
continuous high-speed.
7
INT
front washer. The front wipers will operate
several times.
8
REAR WIPER AND WASHER
7 Intermittent (INT) – Rear wiper
8 Low (ON) – Rear wiper operates at a continuous low-speed.
9 Push the lever forward to activate the rear washer. The rear wiper will
ON
operates intermittently.
operate several times.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
18
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 18
9/16/16 1:17 PM
3
1
8
4
9
10
5
6
2
7
HEATER AND AIR CONDITIONER (automatic)
1 AUTO BUTTON/DRIVER’S SIDE TEMPERATURE CONTROL DIAL
The automatic mode may be used year-round. Press the AUTO button to
turn the system on, and the system will automatically control the inside
temperature (automatic cooling and/or dehumidified heating), air flow
distribution and fan speed.
Turn the driver’s side temperature control dial to the left for cooler air or to
the right for warmer air.
2 DUAL BUTTON/PASSENGER’S SIDE TEMPERATURE CONTROL DIAL
Press the DUAL button to turn the passenger’s side temperature controls
on or off. This will allow the passenger’s side temperature to be adjusted
independently from the driver’s side by turning the passenger’s side
temperature control dial.
Turn the passenger’s side temperature control dial left for cooler air or right
for warmer air.
3 ON•OFF BUTTON
Press the button to turn the system on or off.
4 FAN SPEED CONTROL BUTTONS
Press either the
or the
button to decrease or increase fan speed.
5 MODE BUTTON
Press the MODE button to cycle through the following air flow outlets:
Air flows from the center and side vents.
Air flows from the center, side and foot vents.
Air flows mainly from the foot vents.
Air flows from the front defroster and foot vents.
6 AIR RECIRCULATION CONTROL BUTTON
Press the air recirculation control
button 6 to recirculate interior
air inside the vehicle. The indicator light on the button will illuminate. This
system is used to avoid certain outside odors and to adjust the inside vehicle
temperature more effectively.
The air recirculation mode cannot be activated when the climate control
system is in the front defroster mode
FRONT or the front defroster and
foot vent mode
.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 19
19
9/16/16 1:17 PM
FIRST DRIVE FEATURES
7 FRESH AIR INTAKE CONTROL BUTTON
Press the fresh air intake control
button 7 to draw outside air into
the passenger compartment. The indicator light on the
button will
illuminate and the indicator light on the
button 6 will extinguish.
8 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Press the front defroster
FRONT button to turn the system on. This
feature removes humidity from the air.
Turn the temperature control dial 1 to set the desired temperature.
To defrost the front and side windows quickly, set the temperature controls
and fan speed controls to their maximum settings.
9 DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS (if so equipped)
REAR switch to turn the system on or off.
Push the rear window defroster
This function automatically turns off after approximately 15 minutes.
10 A/C BUTTON
Press the A/C button to turn the air conditioner system on or off. This system
helps cool and dehumidify the air inside the cabin and defog
the windows.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” and the “Display screen, heater,
air conditioner, audio and phone systems (section 4)” of your Owner’s Manual.
6
7
8
9
3
5
10
1
4
2
FM/AM/SiriusXM® SATELLITE RADIO WITH CD PLAYER
AND NAVIGATION
Touch the
“Audio” key 2 on the Launch Bar to display the current
audio source.
Touch the
“Audio” key 2 a second time to access the source
selection screen.
20
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 20
9/16/16 1:17 PM
1 PUSH
(on•off) BUTTON/VOL (volume) CONTROL KNOB
Press the PUSH
Turn the VOL (volume) control knob right or left to increase or decrease
the volume.
2 3 (on•off) button to turn the audio system on or off.
AUDIO KEY
Touch the
“Audio” key on the Launch Bar to bring up the current source’s
control screen.
/
(seek and cat/track) BUTTONS
To scan quickly through each broadcasting station, press the
to move to the previous or next broadcast station.
For satellite radio to switch to the first channel of the previous or next
category, press the
or
button.
To change tracks on a CD, press the
To rewind or fast forward a track on a CD, press and hold the
or
button.
or
or
button
button.
4 PUSH SOUND BUTTON/TUNE/SCROLL KNOB
Press the PUSH SOUND button to cycle through the audio settings
individually and use the TUNE/SCROLL knob to adjust the
current setting.
Touch the
“Settings” key on the Launch Bar and then touch the “Sound”
key to view all audio settings.
To manually tune the radio, turn the TUNE/SCROLL knob left or right.
5 AUDIO (source) BUTTON
Pressing this button will give access to the AM, FM, SXM, CD, USB1/iPod,
USB2/iPod, Bluetooth Audio or AUX audio source.
Twelve memory stations can be set for the FM band, six for the AM band and
18 for satellite radio. These appear at the bottom of the screen when one of
these sources is selected.
To store a station in a preset, you must first select a radio band by touching
the “AM” 6 , “FM” 7 or “SXM” key 8 then tune to the desired AM, FM or
satellite radio station. Next, touch and hold the desired station preset key
(1-6) until you hear a beep. The channel indicator will then display, and the
sound will resume. Programing is now complete.
To retrieve a previously set station, select the radio band where the preset
was stored then touch the corresponding station select key (1-6).
6 AM KEY / 7 FM KEY
Touch the “AM” 6 or “FM” 7 key. Next, the touch the “AM Menu” or
“FM Menu” key to view the station list or turn HD mode on or off.
Tag favorite songs to save to an iPod®.
• Apple® website: If you are listening to a radio station that supports iTunes
Tagging, you can tag a song you hear so you can preview and purchase it
later on the iTunes Store. Songs that can be tagged are marked with a tag
icon next to the song title or on the “Now Playing” screen.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 21
21
9/16/16 1:17 PM
FIRST DRIVE FEATURES
8 SXM KEY
Touch the “SXM” key 8 . Next, touch the “SXM Menu” key to bring up the
categories, favorites and replay options.
9 CD KEY
Touch the “CD Menu” key to view the track list.
10 AUX KEY
A cable with 1/8-in (3.5 mm) stereo mini plugs is required for audio playback.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Audio system (section 3)” of your Navigation System Owner’s Manual.
USB (Universal Serial Bus) CONNECTION PORT/iPOD®
INTERFACE AND AUX JACK
The USB ports are located in the media
pocket 1 with the AUX jack and at the rear
of the center console 2 (if so equipped).
USB1/iPod® and USB2/iPod®
1
• When a device is connected via USB, the
system will automatically start playing music
from it.
• This system supports Apple® devices and
USB memory devices. Only Apple® brand or Apple® certified
cables will work. NISSAN cannot guarantee compatibility with
aftermarket cables that are not certified by Apple®.
• The system may not be compatible with some versions
of Android®.
2
Touch the “USB/iPod® Menu” key to view folder list and track listing, playlist,
albums, artist and songs.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Display screen, heater, air conditioner, audio and phone systems
(section 4)” of your Owner’s Manual or the “Audio system (section 3)” of your Navigation System
Owner’s Manual.
CRUISE CONTROL (if so equipped)
22
The cruise control system enables you to set
a constant cruising speed once the vehicle
has reached 25 mph (40 km/h).
The system will automatically maintain the
set speed until you tap the brake pedal,
accelerate, cancel or turn the system off.
4
3
1
2
To activate the cruise control, push the ON/OFF switch 1 on the steering
wheel. The CRUISE indicator light in the instrument panel will illuminate.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 22
9/16/16 1:17 PM
To set a cruising speed, accelerate the vehicle to the desired speed, push the
SET/- switch 2 on the steering wheel and release. Take your foot off the
accelerator pedal. Your vehicle will maintain the set speed.
To reset at a faster cruising speed, push and hold the RES/+ switch 3 on the
steering wheel. When the vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the SET/- switch 2 on the
steering wheel. Release the switch when the vehicle slows to the desired speed.
To cancel the preset speed, tap the brake pedal or push the CANCEL switch 4
on the steering wheel.
To turn off cruise control, push the ON/OFF switch 1 on the steering wheel.
The CRUISE indicator light in the instrument panel will extinguish.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
INTELLIGENT CRUISE CONTROL (ICC) (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
To set Vehicle-To-Vehicle Distance Control mode, press the CRUISE ON/OFF
button 1 on the steering wheel. The CRUISE indicator light 2 will illuminate.
Accelerate to the desired speed.
Push down on the SET/- switch 3 on the
steering wheel and release it. ICC will be set
to the desired speed.
Press the distance button 4 on the steering
wheel repeatedly to change the set distance
between long, middle and short.
When a vehicle is not detected ahead of you
in the lane, the set distance and set vehicle
speed indicator lights will illuminate 5 in
set mode.
When a vehicle is detected ahead of you in the lane, the
vehicle ahead detection, set distance and set vehicle speed
indicator lights will illuminate 6 in set mode.
To reset at a faster cruising speed, push and hold the
RES/+ switch 7 on the steering wheel. When the vehicle
attains the desired speed, release the switch.
5
To reset at a slower cruising speed, push and hold the
SET/- switch 3 on the steering wheel. Release the switch
when the vehicle slows to the desired speed.
6
To cancel the preset speed, push the CANCEL switch 8 on the steering wheel
or tap the brake pedal. The set vehicle speed indicator 5 will extinguish.
8
4
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 23
7
3
1
2
23
9/16/16 1:17 PM
FIRST DRIVE FEATURES
To turn off ICC, press the CRUISE ON/OFF button 1 on the steering wheel. The
CRUISE indicator light 2 in the instrument panel will extinguish.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
FRONT ARMREST/CENTER CONSOLE STORAGE BOX
To access the top storage tray, pull up on
the lever 1 .
1
Lift or slide the tray 2 to access the bottom
storage bin.
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
For more information, refer to the “Instruments and controls
(section 2)” of your Owner’s Manual.
24
2
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 24
9/16/16 1:17 PM
SYSTEM GUIDE
2
TRIP COMPUTER
When the
arrow buttons 1 on the
steering wheel are pressed, the following
screens will appear on the vehicle
information display 2 :
Home – Displays the current speed, the
compass and the additional media that
is available.
Audio – Displays the current playing media.
3
1
1
Compass (if so equipped) – Displays the
vehicle’s current heading.
Drive Computer – Displays Average
Fuel Economy, Average Speed, Trip
Computer and Time of the Trip. Each can be reset individually.
Fuel Economy – Displays Average Fuel Economy. Press and hold the OK
button 3 on the steering wheel to reset.
Driving Aids (if so equipped) – Displays the Driving Aids that are equipped
on your vehicle. Use the OK button 3 on the steering wheel to turn each
system on or off.
Tire Pressure Monitoring System (TPMS) – Displays the individual tire’s
pressure while driving.
Warning – Displays the current warnings.
SETTING – Displays the available settings that can be changed.
— Press the
arrow buttons 1 on the steering wheel to cycle through
the various setting modes.
— P
ress the OK button 3 on the steering wheel to choose the
selected menu.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 25
25
9/16/16 1:18 PM
SYSTEM GUIDE
HANDS-FREE TEXT MESSAGING ASSISTANT* (if so equipped)
This system allows for sending and receiving
text messages through the vehicle’s interface.
Using predefined or custom messages, send
a text to an entry stored in your Bluetooth®
Hands-free Phone System.
Once enabled, the text message, sender and
delivery time are shown on the control panel
display when the vehicle speed is less than
5 mph (8 km/h).
Text messages have the option of being read aloud at all vehicle speeds.
Once the vehicle is in motion, text messages can only be replied to using the
Voice Recognition
button on the steering wheel.
Custom text messages can be created manually when the vehicle is not
in motion.
Custom text messages must be created in advance.
Many cellular phones may require special permission to enable text messaging.
Check the cellular phone’s screen during Bluetooth® pairing and accept
any permission requests for message access or text messages. For some
cellular phones, you may need to enable “Notifications” in the cellular phone’s
Bluetooth® menu for text messages to appear on the touch-screen display.
For more detailed information and instructions, refer to your cellular phone’s
Owner’s Manual.
Text message integration requires that the cellular phone support Message
Access Profile (MAP) for both receiving and sending text messages. Some
cellular phones may not support all text messaging features. Please see
www.NissanUSA.com/bluetooth for compatibility information as well as
your device’s Owner’s Manual.
*Laws in some jurisdictions may restrict the use of “Text-to-Speech”. Some of the applications and
features, such as social networking and texting, may also be restricted. Check local regulations for any
requirements before using these features.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Hands-free phone (section 4)” of your Navigation System
Owner’s Manual.
26
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 26
9/16/16 1:18 PM
NISSANCONNECTSM SERVICES POWERED BY SiriusXM®
(if so equipped)
NissanConnectSM Services is a collection of security and convenience services that
add innovation to your daily drive.
To enroll in NissanConnect Services, create an account or log into your
Nissan Owner Portal with your Vehicle Identification Number (VIN). Under the
NissanConnect Services tab, select the red button next to Manage Subscription.
Follow the prompts to enroll in NissanConnect Services. Next, download the
NissanConnect Services companion app and
log into it using your Nissan Owner Portal ID
and password.
For full details on NissanConnectSM Services
or to enroll your vehicle, please visit
www.NissanUSA.com/connect or call
855-426-6628.
1
ere is a quick overview of some of the features
H
that may be available for your vehicle. A full
description of these and other NissanConnect Services can be found in your
Navigation System Owner’s Manual.
Automatic Collision Notification – A service that generates an automatic
connection between the vehicle and the Emergency Response Center when the
vehicle has been involved in an accident that was severe enough to deploy the
air bags.
Emergency Call – Connects you to a NissanConnect Services Specialist who will
assist in the dispatch of emergency services to the vehicle’s location. To use this
feature, press the SOS button 1 on the overhead console. The SOS button 1
should only be used in emergency situations.
Roadside Assistance – Dispatches roadside
assistance to the vehicle’s location in
non-emergency situations. Roadside
Assistance can be accessed by touching the
2 on the map screen, via
headset icon
NissanConnect Services companion app
or by calling the Roadside Assistance
provider directly.
2
Stolen Vehicle Locator – A service that works
in coordination with law enforcement agencies to assist in the recovery of
a stolen vehicle.
Remote Engine Start/Stop – Use your smartphone to heat up or cool down your
Nissan to the comfortable temperature it was when you left it.
Remote Door Lock/Unlock – For use when you forget to lock your vehicle or if
you need to open it and do not have the keys. To use this feature, log into the
NissanConnect Services companion app or website or contact a NissanConnect
Services Response Specialist.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 27
27
9/16/16 1:18 PM
SYSTEM GUIDE
Assisted Search – A feature that allows you to verbally request point-of-interest
or destination data from a live operator by touching the headset
icon 2 on
the map screen.
Journey Planner – You can send a route with a destination and up to five way
points directly to the vehicle.
Boundary Alert – A feature that allows you to monitor the movement of your
vehicle in and out of specified regions you have set on the Monitoring section of
the NissanConnect Services web portal or companion app.
Speed Alert – Sends you alerts when your vehicle speed exceeds a threshold you
have set on the NissanConnect Services web portal or companion app.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Other settings (section 5)” and the “General system information
(section 6)” of your Navigation System Owner’s Manual.
28
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 28
9/16/16 1:18 PM
2
3
1
APPLE CARPLAY™ (if so equipped)
The in-vehicle system can be used as a controller for some of the iPhone®
functions through Apple CarPlay™.
If your iPhone® is compatible, Apple CarPlay™ can be used.
•S
elect the
• Select “Apple CarPlay” 2 from the menu.
“MENU” key 1 on the screen.
Before using Apple CarPlay™, confirm the following settings on your iPhone®:
• Turn on “CarPlay” on your iPhone®.
•S
elect “Settings” —> “General” —> “Restrictions” and turn off “Restrictions” or
turn on CarPlay.
• Turn on “Siri®” on your iPhone®. Select “Settings” —> “General” —> “Siri®” and turn
on Siri®.
To connect your CarPlay™-capable iPhone® to the system, you must connect
the iPhone® cable to the USB port located in the center console.
•D
epending on the setting, the “Startup Information” screen will appear.
• Touch “Yes” to use Apple CarPlay™.
• The Apple CarPlay™ top menu screen will appear, and the iPhone® functions
displayed on the screen can be operated by the in-vehicle system.
• To return to the “Apple CarPlay” top menu screen after operation, touch the
key 4 on the lower left corner of the “Apple CarPlay” screen.
• To exit the “Apple CarPlay” screen and display the other screens, press the
MENU button or one of the other buttons on the control panel and touch
the preferred menus.
• To return to the “Apple CarPlay” screen, touch the “Info” key 3 on the
Launch Bar and then touch the “Apple CarPlay” key 2 .
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 29
29
9/16/16 1:18 PM
SYSTEM GUIDE
When connected to Apple CarPlay™, Siri®
Eyes Free operation can also be accessed.
There are two ways to start a Siri® Eyes
Free session.
1. P
ress and hold the
steering wheel.
2. Touch and hold the
key 4 at the
lower left corner of the “Apple
CarPlay” screen.
button on the
4
Press the
button on the steering wheel or touch the
key 4 at the lower
left corner of the “Apple CarPlay” screen to end Siri® Eyes Free operation.
Keep the interior of the vehicle as quiet as possible. Close the windows to
eliminate the surrounding noises (traffic noises, vibration sounds, etc.), which
may prevent the system from recognizing the voice commands correctly.
Some Siri® Eyes Free functions may not be available during driving.
For functions that can be used with Siri® Eyes Free, please refer to the
Apple® website.
Nissan Phone menu and Nissan Voice Recognition cellular phone commands will
not be available when Apple CarPlay™ is active.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the ”Getting started (section 2)” and the ”Information (section 5)” of your
Navigation System Owner’s Manual.
BLUETOOTH® HANDS-FREE PHONE SYSTEM*
A cellular telephone should not be used
while driving so full attention may be given to
vehicle operation.
Bluetooth®
Controls
SYSTEM OPERATING TIPS
Press the
button on the steering wheel to
interrupt the voice prompts at any time and
speak a command after the tone.
The “Help” command can be used to hear a
list of available commands at any time.
Reduce background noise as much as
possible by closing windows and pointing
HVAC vents away from the ceiling.
Speak naturally without long pauses and
without raising your voice.
If you experience difficulty with the Voice Recognition
System recognizing a contact name, please try saying both
the first and last name of the contact as this improves
recognition accuracy.
30
Microphone
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 30
9/16/16 1:18 PM
To cancel a Voice Recognition session, say “Cancel” or “Quit” or press and hold
the button on the steering wheel for 5 seconds.
For more detailed information and instructions, refer to your cellular phone’s
Owner’s Manual and visit www.NissanUSA.com/bluetooth.
*Some jurisdictions prohibit the use of cellular telephones while driving.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Display screen, heater, air conditioner, audio and phone systems
(section 4)” of your Owner’s Manual or please visit www.NissanUSA.com/bluetooth.
BLUETOOTH® SYSTEM WITH NAVIGATION* (if so equipped)
Bluetooth® Streaming Audio allows you to use a compatible Bluetooth® cellular
phone to play audio files on your device. Your compatible cellular phone can be
connected to the vehicle’s audio system, allowing audio files to play through the
vehicle’s speakers.
CONNECTING PROCEDURE
The vehicle must be stationary when
connecting the cellular phone.
1.Press the
button on the steering wheel
and touch the “Connect Phone” key.
2. Initiate connecting from the cellular phone.
• The connecting procedure varies according
to each cellular phone model. For detailed
connecting instructions and a list of
compatible cellular phones, please visit
www.NissanUSA.com/bluetooth.
• When prompted, confirm the PIN on the
display with the PIN shown on the handset.
If your device does not support Secure
Simple Pairing and requests you to input a
PIN, enter “1234” from the handset.
• Some cellular phones may require you
to accept certain permissions in order to
enable features on your Bluetooth® system.
During the Bluetooth® pairing process,
please check your cellular phone’s display
for a pop-up with the request to grant
phonebook access.
• Granting phonebook access permission will
allow your contacts to be downloaded to
the vehicle’s Bluetooth® system. A pop-up
may display on your cellular phone stating
that the Bluetooth® system would like to
access your contacts and call history.
Please select “Allow” or “Yes” to grant
this permission.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 31
31
9/16/16 1:18 PM
SYSTEM GUIDE
If your cellular phone presents the option to not show the message again,
please make sure that this item is checked. Doing so will ensure that any
changes to your phonebook will be synced with the Bluetooth®
system automatically.
• Some cellular phones may incorrectly state that the connection was
unsuccessful. Please verify that the touch-screen displays that the connection
is successful, or touch
“Settings” > “Bluetooth” > “Select BT Device” > “Phone”
and confirm that your cellular phone is listed.
3.When connecting is complete, the screen will return to the Phone
menu display.
PHONEBOOK SETUP
MENU button on the control panel.
P
ress the
Touch the
“Settings” key on the Launch Bar and touch the
“Phonebook” key.
Depending on your cellular phone, the system may automatically download
your cellular phone’s entire phonebook to the vehicle’s Bluetooth®, system.
During the Bluetooth® pairing process, please check your cellular phone for
any requests to download your phonebook or contacts to the vehicle system.
If your cellular phone requests permission to download your contacts, please
select “Allow” or “Yes”. For additional information, please reference “Connecting
Procedure” in this section.
The Quick Dial phonebook can also be set for up to five entries that can be used
with your cellular phone.
1.Press the
2.Touch the “Add New” key at the top of the display. There are different
methods to input a phone number. Select one of the following options:
button on the steering wheel and touch the “Quick Dial” key.
• “Copy from Call History” to save a number
from the Outgoing, Incoming or Missed
Calls lists.
• “Copy from the Phonebook” to save a
number that has been downloaded from
your handset to the vehicle.
• “Enter Number by Keypad” to input the
number and name manually.
MAKING A CALL
To make a call, follow this procedure:
1.Press the button on the steering wheel. The
Phone menu will appear on the control
panel display.
2.Touch the “Quick Dial”, “Call History”,
“Phonebook” or “Dial Number” key.
3. Touch the desired entry from the list.
4.Touch “Number” to start dialing.
32
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 32
9/16/16 1:18 PM
RECEIVING/ENDING A CALL
To accept the call, press the
button on the
steering wheel or touch the “Answer” key on
the display.
To reject the call, press the button on the
steering wheel or touch the “Decline” key on
the display.
To hang up, press the button on the
steering wheel or touch the “Hang up” key
on the display.
*Some jurisdictions prohibit the use of cellular telephones
while driving.
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating
and feature information.
To view detailed instructional videos regarding these and
other features, please go to www.nissanownersinfo.mobi.
For more information, refer to the “Display screen, heater, air
conditioner, audio and phone systems (section 4)” of your Owner’s Manual , the “Hands-free phone
(section 4)” of your Navigation System Owner’s Manual or please visit www.NissanUSA.com/bluetooth.
BLUETOOTH® SYSTEM WITHOUT
NAVIGATION* (if so equipped)
PAIRING PROCEDURE
1. Press the ENTER/SETTING button.
2. Select the “Bluetooth” key.
3. Select the “Add Phone” key. This same screen
can be accessed to remove, replace or select a
different Bluetooth® device.
4. The system acknowledges the command
and asks you to initiate connecting from the
cellular phone handset. The connecting procedure of the cellular phone varies
according to each cellular phone model. For additional information, refer to the
cellular phone’s Owner’s Manual for details. You can also visit www.NissanUSA.
com/bluetooth for instructions on connecting Nissan-recommended
cellular phones.
• When prompted, confirm the PIN on the display with the PIN shown on the
handset. If your device does not support Secure Simple Pairing and requests
you to input a PIN, enter “1234” from the handset.
PHONEBOOK REGISTRATION
When the cellular phone is connected to the in-vehicle module, the data stored
in the cellular phone, such as phonebook, outgoing call logs, incoming call logs
and missed call logs, is automatically transferred and registered to the system.
The availability of this function depends on each cellular phone. The copying
procedure also varies according to each cellular phone. Refer to the cellular
phone’s Owner’s Manual for more information.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 33
33
9/16/16 1:18 PM
SYSTEM GUIDE
Up to 1,000 entries per registered cellular phone can be stored in
the phonebook.
MAKING A CALL
1.Press the
button on the steering wheel. The system will announce the
available commands; afterward, a tone will sound.
2.Say: “Call”. The system acknowledges the command and announces the next set
of available commands.
3.Say the registered person’s name. The system acknowledges the command and
announces the next set of available commands.
4.Say: “Yes”. The system acknowledges the command and makes the call.
RECEIVING/ENDING A CALL
To accept the call, press the
To reject the call, press the
To hang up, press the
button on the steering wheel.
button on the steering wheel.
button on the steering wheel.
*Some jurisdictions prohibit the use of cellular telephones while driving.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
To view detailed instructional videos regarding these and other features, please go to
www.nissanownersinfo.mobi.
For more information, refer to the “Display screen, heater, air conditioner, audio and phone systems
(section 4)” of your Owner’s Manual.
BLUETOOTH® STREAMING AUDIO*
If you have a compatible Bluetooth® device
with streaming audio (A2DP profile), you can
set up the wireless connection between your
Bluetooth® device and your vehicle’s audio
system. This connection allows you to listen
to audio from the Bluetooth® device using
your vehicle’s speakers.
1
A cellular telephone should not be used while
driving so full attention may be given to
vehicle operation.*
CONNECTING PROCEDURE WITH NAVIGATION
SYSTEM (if so equipped)
1.Touch the
“Audio” key and select the
“Bluetooth Audio” key.
2.A prompt to connect your device will display.
• If the device needs to be connected:
“Settings” key.
a. Touch the
b. Touch the “Bluetooth” key.
c. Touch the “Connect Device” key 1 .
Touch the “BT Menu” key to view track listing, artist, songs or albums.
Touch the “BT Settings” key to change which device is playing audio.
34
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 34
9/16/16 1:18 PM
CONNECTING PROCEDURE WITHOUT NAVIGATION SYSTEM (if so equipped)
To connect your Bluetooth® audio device to the
vehicle, follow the procedure below:
1. Press the SETTING button.
2. Select “Bluetooth”.
3.Select “Add Phone”. This same screen can
be accessed to remove, replace or select a
different Bluetooth® device.
4.The system acknowledges the command
and asks you to initiate connecting from
the cellular phone handset. The connecting
procedure of the cellular phone varies according to each cellular phone model.
For additional information, refer to the cellular phone’s Owner’s Manual for
details. You can also visit www.NissanUSA.com/bluetooth for instructions on
connecting Nissan-recommended cellular phones.
To switch to the Bluetooth® audio mode, press the MEDIA button repeatedly
until the Bluetooth® audio mode is displayed on the screen. If attempting to
stream audio from your device over Bluetooth®, please ensure that your device’s
music application is open and audio is ready to be played.
The controls for the Bluetooth® audio are displayed on the screen. Use the preset 3
button for play and the preset 4 button for pause.
*Some jurisdictions prohibit the use of cellular telephones while driving.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Display screen, heater, air conditioner, audio and phone systems
(section 4)” of your Owner’s Manual or the “Audio system (section 3)” of your Navigation System Owner’s
Manual or please visit www.NissanUSA.com/bluetooth.
HOMELINK
HOMELINK® UNIVERSAL TRANSCEIVER (if so equipped)
The HomeLink® Universal Transceiver can learn and consolidate the functions
of up to three different hand-held transmitters, operating items such as garage
doors, property gates, outdoor and indoor lights or alarm systems.
To program the HomeLink® Universal Transceiver:
• Position the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink
surface, keeping the HomeLink indicator light in view.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 35
35
9/16/16 1:18 PM
SYSTEM GUIDE
• Press and hold the desired HomeLink button and the handheld transmitter
button simultaneously until the HomeLink indicator light flashes slowly and
then rapidly.
• Both buttons may be released when the indicator light flashes rapidly.
To verify the programing is complete, press and hold the HomeLink button and
observe the indicator light:
• A solid, continuous light indicates the programing is complete and the
HomeLink button will activate your device.
• A blinking light that turns to a solid, continuous light after 2 seconds indicates
additional steps are required to complete the programing.
An additional person may make the remaining steps easier. To complete the
programing process:
• At the receiver of the device that you are programing to the HomeLink
button, press and release the learn or smart button (the name may vary by
manufacturer, but it is usually located near where the hanging antenna wire is
attached to the unit). You have approximately 30 seconds to initiate the
following step.
• Press and hold the programed HomeLink button for 2 seconds and release.
You may have to repeat the previous two steps up to three times to complete
the programing process. HomeLink should now activate your device.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual,
the HomeLink website at www.homelink.com or call 1-800-355-3515.
3
2
6
7
5
1
8
4
10
9
NAVIGATION SYSTEM (if so equipped)
36
Your Navigation System can calculate a route from your current location to
a preferred destination. The real-time map display and turn-by-turn voice
guidance will lead you along the route.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 36
9/16/16 1:18 PM
The Navigation System will continually update your vehicle’s position. If you have
deviated from the original route, it will recalculate the route from your
current location.
To help promote safe driving, some functions cannot be operated or have
limited operation when the vehicle speed is above 5 mph (8 km/h). The onscreen text and keys for these restricted functions will be grayed-out or muted
and cannot be selected while driving. These functions will become available
again when the vehicle speed is reduced to 5 mph (8 km/h). Voice commands
may be available for some of the restricted functions. For more information,
refer to the “Display screen, heater, air conditioner, audio and phone systems
(section 4)” of your Owner’s Manual and the “Information (section 5)” of your
Navigation System Owner’s Manual.
1 MENU – Touch to access all items in the menu, including Navigation items.
2 Touch-screen
3 MAP Menu – Touch to access different options related to either a selected
location by touch or one that you have navigated to. Some options include
“Save Location”, “Nearby POIs” or “Map Icons”.
Navi (Navigation) – Touch to access the Navigation function.
4 5 Info (Information) – Touch to display the vehicle, traffic (if so equipped) and
weather (if so equipped) information.
6 ZOOM OUT, 7 ZOOM IN – Touch to adjust the map scale. When parked, you
can pinch out or in to zoom on the screen.
Map – Touch to display the map.
8 Settings – Touch to display the system settings.
9 Compass – Map view can be changed by touching the compass when on
the main map screen.
10 SETTING DESTINATION
You can set a destination with your Navigation System using the touch-screen
display or Voice Recognition.
Touch-screen Display
• Touch the
“Navi” key on the Launch Bar.
Voice Recognition
• Press the
button on the steering wheel, and after the tone, say “Navigation”.
From here, the system will give you the options available for setting
a destination.
The fastest route is set as the default; to change this to a minimized freeway or
shortest distance route, go to “Settings” > ”Navigation” > “Route Settings”.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 37
37
9/16/16 1:18 PM
SYSTEM GUIDE
SETTING A DESTINATION USING POINTS OF INTEREST (POI)
Touch-screen Display
“Navi” key on the Launch Bar.
• Touch the
• Touch the “Points of Interest” key and then select one of the displayed options
for choosing your destination.
Voice Recognition
• Press the
button on the steering wheel, and after the tone, say “Navigation”
then say “Points of Interest”. From here, the system will give you the options
available for setting a POI.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to your Navigation System Owner’s Manual.
38
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
2580654_17b_Murano_US_pQRG_091616.indd 38
9/16/16 1:18 PM
MEMO
2580654_17b_Murano_US_pQRG_091616.indd 39
9/16/16 1:18 PM
MEMO
2580654_17b_Murano_US_pQRG_091616.indd 40
9/16/16 1:18 PM
MEMO
2580654_17b_Murano_US_pQRG_091616.indd 41
9/16/16 1:18 PM
Helpful Resources
Below is a list of helpful resources that can be used to
learn more about the vehicle’s systems and
feature operations.
Vehicle Owner’s Manual
Navigation System Owner’s Manual (if so equipped)
Printed Quick Reference Guide (this document)
www.NissanUSA.com/bluetooth
www.NissanUSA.com/connect
www.youtube.com/user/NissanUSA
Nissan Consumer Affairs: 1-800-647-7261
Electronic Quick Reference Guide
(Use Quick Response (QR) code or URL below.)
Nissan Quick Guide (available in the iPhone App
Store or Android Google Play Store for download to
your smartphone)
To view detailed instructional videos,
go to www.nissanownersinfo.mobi/2017/murano
or snap this barcode with an appropriate
barcode reader.
This Quick Reference Guide is intended to provide an overview of some of the unique features of your new
vehicle. Please see your Owner’s Manual for important safety information and system operation limitations.
Features and equipment in your vehicle may vary depending on model, trim level, options selected, order, date
of production, region or availability. Therefore, you may find information about features or equipment that are
not included or installed on your vehicle.
All information, specifications and illustrations in this Quick Reference Guide are those in effect at the time
of printing. NISSAN reserves the right to change specifications, performance, design or component suppliers
without notice and without obligation. From time to time, NISSAN may update or revise this Quick Reference
Guide to provide owners with the most accurate information currently available. Please carefully read and
retain with this Quick Reference Guide all revision updates sent to you by NISSAN to ensure you have access
to accurate and up-to-date information regarding your vehicle. Current versions of vehicle Quick Reference
Guides, Owner’s Manuals and any updates can also be found in the Owner section of the NISSAN website at
https://owners.nissanusa.com/nowners/navigation/manualsGuide. If you have questions concerning
any information in your Owner’s Manual, contact NISSAN Consumer Affairs. See the NISSAN CUSTOMER CARE
PROGRAM page in the Owner’s Manual for contact information.
Nissan, the Nissan Brand Symbol, Z and
Nissan model names are Nissan trademarks.
© 2017 Nissan North America, Inc.
QR17EA 0Z52U1
Printing: March 2017 (08)
2580654_17b_Murano_US_pQRG_091616.indd 1
9/16/16 1:16 PM
Open as PDF
Similar pages