DIGITAL INTERCOM
www.firecom.com
QUICK REFERENCE
DOWNLOAD DETAILED PRODUCT MANUAL FROM WEBSITE
WWW.FIRECOM.COM/SUPPORT
800.527.0555
503.684.6647
503.620.2943
7340 SW DURHAM RD
PORTLAND OR 97224 USA
Copyright © 2012 Sonetics Corporation - All rights reserved
This document is number 600-1038-00 Rev A
LED COLORS
INTERCOM VOLUME
INTERCOM SQUELCH
Aux Select
Incoming Traffic
CELL
OR
AUX
Monitoring
Radio Select
Incoming Traffic
Outgoing Traffic
RADIO
INPUT/OUTPUT GAIN ADJUSTMENT
1
4
HOLD BOTH BUTTONS
FOR 5 SEC UNITL
LEDS FLASH
5
2
WHEN SATISFIED WITH AUDIO LEVEL,
HOLD FOR 5 SEC TO EXIT ADJUST MODE
PRESS BUTTON OF INPUT /OUTPUT TO ADJUST.
BUTTON LEDS WILL FLASH
3
(INPUT) - ADJUST WITH VOLUME BUTTONS
HAVE A PARTNER SPEAK INTO REMOTE RADIO
3
(OUTPUT) - ADJUST WITH SQUELCH BUTTONS
HAVE A PARTNER LISTEN TO REMOTE RADIO
(INPUT)
LISTEN TO HEADSET AND ADJUST
GAIN USING VOLUME UP/DOWN
4
(OUTPUT)
SPEAK THRU HEADSET TO REMOTE RADIO
AND ADUST USING SQUELCH UP/DOWN
WIRELESS BASE STATION SQUELCH ENABLE/DISABLE
HOLD BOTH SQUELCH
BUTTONS FOR 5 SECONDS
(RED LEDS FLASH)
1
2
PRESS UP/DOWN VOLUME BUTTON
TO SELECT HEADSET
10
9
8
7
6
5
4
3
2
1
PRESS SQUELCH UP TO ENABLE
SQUELCH (RED LED ON)
BACK OF INTERCOM
1
3
5
7
9
2
4
6
8
10
3
PRESS SQUELCH DOWN TO
DISABLE SQUELCH (RED LED OFF)
DIGITAL INTERCOM
www.firecom.com
QUICK INSTALL & SCHEMATICS
INTERCOM INSTALLATION
REMOTE HEAD INSTALLATION
2.58
0.81
#8 SHEET METAL SCREWS
USE 3/16” DRILL
MOUNTING BRACKET
CABLE TIES
POWER CABLE CONNECTION
2
GROMMET
HAND KNOB
1.5 AMP FUSE
3.07
1
PIN #2
RED
Mounting Flush to a Flat Surface
1. Remove the 4 Torx bolts (T-10) and nuts from
the corners of the remote head
2. Use the Remote Head as a template to mark
and drill (4) mounting holes: 7/64" diameter for
sheet metal screws or 5/ 32" for machine
screws
3. Drill 3/8" hole in mounting surface and install
the supplied grommet. Pass the wire through
4. For inside installation, mount the panel using
the suppliedscrews (4), making sure the cable
is not pinched Recommended torque : 10
in-lbs
5. Determine the correct length for the CA
cable, and cut cable to correct length
POWER CONNECTOR
ASSEMBLY
PIN #1 BLACK
CLEAN WITH
WIRE BRUSH
7.13
CONNECT BLACK WIRE FROM PIN 1 TO VECHILES
NEGATIVE GROUND OR USE SUPPLIED SELF-TAPPING
SCREW & STAR WASHERS
Mounting with Bracket
1. Remove 4 Torx bolts (T-10) and nuts from the
corners of the remote head
2. Drill 3/4" hole at desired wire pass-through
location on mounting surface
3. Drill (4) mounting holes: 7/64" for #6 sheet
metal screws or 9/64" for #6 machine screws
4. Mount the bracket using included hardware.
Torque : 10 in-lbs
5. Pass cable through grommet and secure with
cable ties as shown
6. Adjust the panel to a desirable viewing angle
with the two hand knobs
WIRING SCHEMATICS
REMOTE HEAD WIRING
Pin 1
Pin 6
BLU
GND
YLW
BUSY +
GRN
BUSY -
RED
DATA L
BLK
DATA H
WHT
POWER
HEADSET MODULE WIRING
Pin 6
PWR
DATA H
DATA L
BUSY BUSY +
GND
Pin 1
TO INTERCOM
Pin 1
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
Pin 6
TO HEADSET MODULE
TO INTERCOM
TO REMOTE HEAD
MR-OX Radio Interface
Cable
5 CONDUCTOR JACK
W/ GND RING
AUX PLUG
PINOUT
PP-20 WIRING
Pin 6
AUX OUT HI
AUX IN LO
AUX IN HI
GND
4
Pin 1
WHITE
SPEAKER HIGH
BLACK
SPEAKER LO
RED
MIC HIGH
GREEN
MIC LOW
YELLOW
PTT
BLUE
NOT CONNECTED
5
1
4
1
2
3
2
TO INTERCOM
3
2
1
HEADSET MODULE WIRING
3
PIN #2: RED - TX AUDIO LO
2
1
PIN #3: ORANGE- PTT HI
PIN #4: YELLOW - PTT REFERENCE
Pin 6
PIN #5: GREEN - HOOK SWITCH RELAY (N.O)
PIN #6: BLUE - RX AUDIO HI
PIN #7: VIOLET - RX AUDIO LO
PIN #8: GRAY - HOOK SWITCH RELAY (N.C.)
PIN #9: BLACK - HOOK SWITCH RELAY (C.)
1
4
PIN #1: BROWN - TX AUDIO HI
Pin 1
TO INTERCOM
NOT USED
SPEAKER HI
SPEAKER LO
MIC HI
MIC LO
PTT
TO INTERCOM
3
4
5
5 CONDUCTOR PLUG
2
5
3
4
5
5 CONDUCTOR PLUG
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
Pin 1
Pin 6
TO DAISY CHAINED
HEADSET MODULE
Open as PDF
Similar pages