COCKPIT
GB
MANUAL
www.trelock.de
2
FC 520 / 530 / 535
You have decided to purchase theTRELOCK
bike computer FC 520 (uni-base),
FC 530 (uni-base) or FC 535 (night-light
base) and, as such, your choice is an
excellent one. Your new bike computer is
easy and convenient to operate thanks to
the visual guidance system and large monobutton typical of TRELOCK products. Please
read through this manual prior to your initial
usage of the computer.
36
Contents
1.
Scope of supply
38
2.
Activation of bike computer
39
3.
Insertion of night-light base battery
39
4.
Assembly/Installation
40
5.
Display design and operating principle 45
6.
General default settings
46
7.
Main menus
55
8.
Training
63
9.
Additional information
and instructions
63
37
1. Scope of supply
1.1 FC 520, 530
1.2 FC 535
2x
4x
38
4x
2. Activation of bike computer
3. Insertion of night-light base battery
3.1 FC 535
The display for your bike computer is fed
via a battery in the night-light base. In order to insert this battery, use a coin to turn
the battery compartment cap in an anticlockwise direction and insert the battery
with the + sign pointing upwards (see fig.).
Then turn the cap firmly back in place.
Lithium Battery CR2032
When supplied to the customer, the
battery has already been inserted into the
bike computer. In order to activate the
computer, the red plastic flag must first be
removed. Turn the battery compartment
cap on the bottom of the computer in an
anti-clockwise direction and pull the flag
out. Then turn the cap firmly back in place.
39
3.2 Information on initial operation
By activating the computer, you automatically access the “General Settings” in the
“Set” (SET) menu. How you can change
the general settings is described under
6.1. Should you wish to make changes to
the general settings at a later date, you
can access the “Set” (SET) menu by pressing the MODE button for the appropriate
number of times and then pressing and
holding the SET and MODE buttons for
approx. 3 sec.
40
4. Assembly/Installation
4.1 Assembly/Installation
of handlebar bracket
4.2 FC 520, 530
41
4.3 FC 535
42
4.4 Assembly/Installation
of sensor
43
4.5 Assembly/Installation of magnet
44
5. Display design and operating principle
SET button
Analogue speedometer
display
Visual guidance
system
Display line 1
Change battery
Display line 2
Display line 3
MODE button
45
45
6. General default settings
6.1 Selection of language
Once the computer has been activated,
you automatically access the “Language?”
menu. By pressing the SET button, you
access the language selection option. Use
the MODE button to choose one of the eight
languages shown (German, English, French,
Dutch, Spanish, Italian, Russian or Polish)
and confirm your choice via the SET button.
46
47
6.2 Choice between km/h
and m/h
In the “Dimensions?” menu, “km/h”
is pre-set as the standard unit. If
you wish to accept this default
setting, press the MODE button.
To change it to “m/h”, press the
SET button. Then use the MODE
button to choose between “m/h”
and “km/h” in the “Unit Speed”
window. Confirm your choice via
the SET button.
Dimensions
48
Dimensions
unit speed
set bike
unit speed
6.3 Setting(s) of wheel size(s) (not
applicable to FC 520)
You can use your bike computer on two
bikes, even if their wheel sizes are different. To this end, you need a dedicated
transmitter/bracket unit (Art. ZF 405 for
FC 530 or ZF 409 for FC 535) and a spoke
magnet (ZF 50, accessory, not supplied as
standard) for each bike. In order to make
the settings for Bike 1 and Bike 2 in the
“Set Bike” window, press the SET button.
Use the MODE button to select “Bike 1”
or “Bike 2”. Confirm your choice via the
SET button.
set bike
bike 1
49
Setting(s) of wheel size(s) (wheel
circumference)
Under “Wheel Size 1” or “Wheel Size
2” (only for FC 530, 535), you should
now enter the wheel circumference
of your bike. This can be seen from
the wheel size data shown on the
side of your tyre. Please consult
the table shown on P. 17 for the
appropriate 4-digit number.
Next press the MODE button until
such time as the appropriate digit
appears, then use the SET button
to move to the next digit. Once you
have confirmed the final digit, you
automatically re-access the “Set
Wheel” window. Should you wish
to make settings for a second bike,
press the SET button, otherwise
move to the “Clock” window by
pressing the MODE button.
50
wheel size 1
Wheel size (mm) =
2 x r (mm) x 3,14
1 inch = 25,4 mm
wheel size 1
Wheel Size (WS) Chart (wheel sizes / wheel circumference)
ETRTO
47 – 305
47 – 406
50 – 406
60 – 406
37 – 540
47 – 507
50 – 507
40 – 559
44 – 559
47 – 559
50 – 559
54 – 559
57 – 559
37 – 590
20 – 571
16x1.75x2
20x1.75x2
20/2.00
20/2.35
24x1 3/8 A
24x1.75x2
24/2.00
26x1.5
26x1.6
26x1.75x2
26x1.9
26x2.00
26x2.125
26x1 3/8
26x3/4
WS mm
ETRTO
1272
1590
1593
1665
1948
1907
1910
2026
2051
2074
2089
2114
2133
2105
1954
60 – 559
32 – 630
40 – 622
47 – 622
40 – 635
37 – 622
18 – 622
23 – 622
25 – 622
28 – 622
32 – 622
37 – 622
40 – 622
50 – 622
60 – 622
WS mm
26/2.35
27x1 1/4
28x1.5
28x1.75
28x1 1/2
28x1 3/8x1 5/8
700x18C
700x23C
700x25C
700x28C
700x32C
700x35C
700x40C
28/2.00
28/2.35
2146
2199
2224
2268
2265
2205
2102
2133
2146
2149
2174
2205
2224
2284
2340
51
6.4 Setting the current time
If you wish to change the time, press
the SET button. One after another,
hours, minutes and seconds (start
automatically after confirmation of
minutes) can be changed via the
MODE button. Use the SET button
to confirm your entries and to move
to the next digit.
Clock
52
Clock?
Clock
Clock
Clock
6.5 Entering and changing the PIN anti-theft protection
Use a PIN to protect your bike computer from unauthorised
access. Activation of the bike computer is then only possible
if the correct pin is input. Once the time has been set, you
automatically access the “Change PIN?” window. Here you can
enter your own PIN and, if necessary, subsequently change it. If
you don’t wish to use a PIN, press the MODE button. Otherwise,
after pressing the SET button, you will be asked to enter the
old PIN (default setting is “0000“). To this end, press the MODE
button until such time as the appropriate digit appears and
then use the SET button to move to the next digit. PIN input is
monitored. Should the PIN have been entered incorrectly, the
message “Wrong PIN” appears for approx. 3 seconds and you
will be asked to re-enter the PIN. If the PIN is correct, input a
new PIN of your choice as described above. Once the last digit
has been confirmed via the SET button, PIN entry must be repeated. Should the repeat PIN entry be incorrect, you will return
automatically to the “Change PIN?” window. Note down your
personal PIN on Page 31 so that it is readily available if required!
change PIN?
enter PIN
53
6.6 Entering and changing the PIN time
If the bike computer is in Sleep mode and is not ‘awakened’ for a
set time, it has to be re-activated by entering your PIN. The period
concerned (PIN Time) can be (re)set in the “Set PIN Time” window
– after you have pressed the SET button, you will be asked to
enter your PIN. After correct PIN input, you automatically access
“PIN Time” where you can enter the time of your choice up to max.
240 minutes. If you wish to dispense with the securing of your bike
computer via a PIN, then set the PIN time to “000”.
enter PIN
54
PIN-Time
PIN-Time new?
PIN-Time
6.7 Energy economy function
An energy economy function is linked to the
PIN-time setting.
The PIN-time default setting is 60 min. and
the PIN default setting “0000”. As such, the
clock is displayed in Sleep for 60 min., after
which time the clock display shuts down.
This period of time can be adjusted as described above. If the PIN time is set at 0, the
energy economy function is deactivated and
the clock is displayed on an ongoing basis.
7. Main menus
By pressing the MODE button, you are able
to move between the menus Stopwatch ( ),
Average (MID), Maximum (MAX), Lap (TRIP),
Pilot (PILOT), Total (TOTAL) and Settings (SET).
To enter digits (time, counter levels, etc.),
press the MODE button until the given digit
appears. Use the SET button to move to the
next digit and confirm again via SET after the
last digit has been entered.
If a PIN is set at “0000” and a PIN time at
more than 0, the energy economy function
and the PIN enquiry are activated. This
means that, once the PIN time has elapsed,
the clock display shuts down and the computer can only be re-activated via PIN input.
55
7.1 „Stopwatch” menu
(only FC 530, 535 )
Starting, stopping and resetting
the stopwatch
Use the SET button
to start and stop the
stopwatch.
By pressing and holding
the SET button for 3
seconds, the stopwatch
is reset to “0”.
Current speed
Stopwatch
Menu display
7.3 “Maximum” MAX menu
The maximum speed on the given lap is
displayed via the “MAX” menu.
By pressing and holding the SET button for
3 seconds, you stop the measurement of the
current lap and reset all lap readings on the
computer to “0”.
56
Current speed
Current time
Maximum speed
on current lap
7.2 “Average” MID menu
The “MID“ menu shows the current average
speed of the given lap.
Current speed
Current time
By pressing and holding the SET button for
3 seconds, you stop the measurement of the
current lap and reset all lap readings on the
computer to “0”.
Average speed
of the current lap
7.4 “Lap” TRIP menu
The ride time and lap kilometres ridden are
displayed via the “TRIP” menu.
Current speed
Lap ride rime
By pressing and holding the SET button for
3 seconds, you stop the measurement of the
current lap and reset all lap readings on the
computer to “0”.
Lap kilometres
ridden
57
7.5 “Pilot” PILOT menu
Setting of day kilometre counter
Current speed
Current time
Day kilometre counter (adjustable)
3 seconds
By pressing and holding the SET button for 3
seconds, you can change the display of the
day kilometre counter in the “Set km” window
(only possible with deactivated stopwatch). This
function is helpful if you have made a detour, for
instance, despite the fact that you are otherwise
following a road book.
7.7 “Set” SET menu
Current speed
Total ride time
(for Bikes 1+ 2)
Total kilometres
(for Bikes 1+ 2)
58
7.6 “Total” TOTAL menu
Current speed
Total ride time
(of current bike)
Total kilometres of
current bike
If you wish to use your computer on 2 bikes
(not applicable to FC 520), you must
select the appropriate bike on the
computer prior to starting your
ride. By pressing the SET
button, the bike currently
selected appears on the
Bike 1
display. Use the MODE button
to change bikes and confirm
your selection via the SET button
or, after 5 seconds, the bike displayed
is automatically confirmed.
The total kilometre status and total ride time
of the current bike are displayed via the
“Total” menu.
The total kilometre status can be adjusted via
the “Set” menu, enabling you, for instance,
to transfer the kilometre reading from an
old bike computer to your new TRELOCK
computer.
By pressing and holding the SET button in the
“SET” menu for 3 seconds, you then have the
option of correcting your default settings and
making further settings. Pressing the MODE button
brings you automatically to the menus “Clock?”
“Wheel Size?” with its submenus “Bike 1” and
“Bike 2” (not applicable to FC 520) and “Total
km” one after the other. Press the SET and MODE
buttons simultaneously for 3 seconds to move to
the general default settings (P. 12, Point 6.ff).
59
Setting of time
If you wish to enter the time, press the
SET button. One after another, hours,
minutes and seconds (start automatically
after confirmation of minutes) can be
changed via the MODE button. Use the
SET button to confirm your entries and
to move to the next digit.
After setting the time, the user is guided
out of the menu. In order to make
further setting changes, you have to
again press and hold the SET button for
3 sec. until such time as the “Clock?”
menu appears and then use the MODE
button to move on to “Wheel Size?”
(Wheel Circumference, Bike 1 and Bike
2 (not applicable to FC 520)), “Total
km?“(Kilometre Performance, Bike 1
and Bike 2) and back to “Set”.
60
3 seconds
Clock?
Clock
3 seconds
Clock?
wheel size?
MODE button for
amendment of settings
MODE button for
amendment of settings
Via the menus “Wheel Size”?“ (Wheel
Circumference) and “Total km?” choose
by pressing the MODE button whether
you wish to set levels for “Bike 1?” and/or
“Bike 2?” (not applicable to FC 520),
and then whether you wish to enter the
“Wheel Size?” or “Total km?”. Change
settings in the usual way via the MODE
button and confirm them via the SET
button.
MODE button for
amendment of settings
After confirmation of the last entry, you
return automatically to “Set”.
61
MODE button for
amendment of settings
(not applicable to FC 520)
SET button for
confirming settings
MODE button for
amendment of settings
(not applicable to FC 520)
SET button for
confirming settings
km/h
total km?
62
km/h
bike 1
km/h
bike 2
km/h
total km
8. Training
8.1 Targeted training
Your TRELOCK bike computer gives you a
wide range of options for training in a targeted
manner. You have the possibility, for example,
of monitoring
• how long you train for
• how many kilometres you cover
• how long you need to cover a certain distance.
9. Additional information and instructions
9.1 Battery change
= When this symbol appears, the battery
needs changing.
The bike computer and the night-light base
(only FC 535) run on 3-V CR 2032-type
batteries.
Caution - old batteries are special waste and
may not be disposed of via household waste!
Your personal data continues to be stored
even if there is no battery in your bike
computer.
9.2 Frequently asked questions
Why can’t the bike computer be activated?
The battery is flat and must be replaced.
Why isn’t any other current data displayed
apart from the time?
The bike computer is in Sleep mode – just
press any button of your choice or simply
start cycling.
Why is the incorrect speed displayed?
The wrong wheel size has been entered.
Why is no speed displayed?
The distance between the sensor and the
magnet is too large.
Why does the display go black or react
lethargically?
The operating temperature (5 ˚C – 50 ˚C; 40
˚F – 120 ˚F) has not been reached or has
been exceeded.
Why is the display pale?
The battery is flat and must be replaced.
63
9.3 Resets
9.6 Technical data
Any resets that may be necessary are carried
out automatically. Should a fault nevertheless
occur, remove the battery from the bike computer, wait briefly and then re-insert it.
Operating temperature: 5 ˚C bis 50 ˚C
(40 ˚F und 120 ˚F)
9.4 Maintenance and care
Your TRELOCK bike computer requires no
maintenance and no special care. Just use
a damp cloth for cleaning purposes. Protect
the sensors and receivers from exposure to
extreme temperatures.
Temperatures below – 20 ˚C (– 4 ˚F) and
over 80 ˚C (176 ˚F) can damage the bike
computer. The operating temperature should
lie between 5 ˚C – 50 ˚C (40 ˚F – 120 ˚F).
9.5 Safety instructions
TRELOCK bike computers are designed for
private fitness training and are unsuitable for
commercial or medical applications.
64
Storage temperature:
Battery type for
bike computer
and sensors:
–20 ˚C und 80 ˚C
(–4 ˚F und 176 ˚F)
3 Volt Lithium
CR 2032
9.7 Warranty and service
You have purchased a quality product from TRELOCK. TRELOCK guarantees the initial purchaser for
a period of two years from the date of purchase that
this TRELOCK product is free of defects in respect
of materials and workmanship, and ensures that any
defective product is repaired or replaced with a new
product. Any complaints you may have should be
addressed directly to your dealer/specialist stockist,
who should also be provided with the relevant
purchase receipt. He will ensure that your warranty
entitlement case is handled correctly. The warranty is
only valid providing the product has not been forcibly
opened or damaged. It does not apply for batteries
and such parts as are subject to wear and tear.
Under the terms of this warranty, TRELOCK cannot
be made liable for any damage occurring due to
product defects of any kind whatsoever. Other legal
entitlements in respect of defects remain unaffected
by this warranty. Any questions you may have can
also be addressed to TRELOCK’s customer service
department:
Here you can enter your PIN numbers
PIN
Default PIN setting:
0
0
0
0
My personal PIN:
PIN-Time
Default PIN-time setting:
0
6
0
My personal PIN time:
TRELOCK GmbH, Postfach 7880, 48042 Münster,
Germany, www.trelock.de.
65
130
Open as PDF
Similar pages