Technical manual for washing machine

Technical manual for washing machine
Model code: WMF1020
Contact Caple on 0844 8003830 or for spare parts www.4caple.co.uk
New product information sheet
Product name: WMF1020
Description: Freestanding washing machine
Product code: WMF1020
Features
Energy class A+
Wash class A
Spin efficiency B
16 programmes:
- Cotton 30c
- Cotton 40c
- Cotton 60c + pre-wash
- Cotton 60c
- Cotton 90c
- Delicates cold
- Delicates 30c
- Hand Wash
- Wool 30c
- Synthetic 30c
- Synthetic 40c
- Synthetic 60c
- Duvet 30c
- Express 15 minutes
- Spin
- Daily 45minutes
Options:
- Rinse hold – anti crease
- Extra rinse
- Easy iron
- Intensive wash
- Anti-bacteria
1400rpm max. spin speed
8kg washing capacity
59 Litre water consumption
New product information sheet
Product name: WMF1020
Description: Freestanding washing machine
Product code: WMF1020
LCD display which features
- Electronic clock - delay timer 1 – 24 hours
- Wash progress
- Total time remaining
- Programme and spin speed indicator
Features
Cold fill
Advance balance system – which electronically controls and distributes clothes evenly during
the spin cycle.
Child lock
Variable load
340mm extra large door
180 degree opening, for easy access.
Stainless steel drum
Self cleaning pump and filter
Anti-flood safety device
Spin system with wash optimization with minimum water and energy consumption.
Foam control
Electrical connection
Rated load 2.2kw ok
Fuse rating 13A ok
t e c h n i c a l
How to use this manual
This document is intended for all persons rendering technical support services (T.S.S.).
It is designed to facilitate the repair of the product described. It provides documentary
support for technical consultations.
This manual contains notes warning about safety issues:
Electrical hazard: This identifies potential risks for the
product. Such risks may cause permanent damage to the
product.
!
I
Warning: This identifies information or circumstances that
may cause personal injuries or death.
Important: This identifies information that is critical for a
correct understanding of the product.
t e c h n i c a l
Table of contents
1.- Warnings and precautions ..................................1
2.- Features ................................................................3
3.- Description of operation.......................................8
3.1.- General description ............................................................ 8
3.1.1.- Component characteristics ....................................................... 8
3.1.2.- V3 and V4 circuit configuration ................................................11
3.1.3.- Washing machine vibrations ................................................... 16
3.1.4.- Description of the operation of programme no. 2 ................... 19
3.1.5.- Attempts to spin ....................................................................... 20
3.2.- Drawings and diagrams ................................................... 21
t e c h n i c a l
Warnings and precautions
1.- Warnings and precautions
!
The washing machine must be connected to an earth. If this basic safety rule is
not respected, the manufacturer shall under no circumstances accept liability for
injuries suffered by persons or for damage to objects.
To prevent fire and electrical sparking hazards, personal injury, or other damage when using your washer, take the following precautions:
This washing machine iis supplied with a manual which includes operating,
maintenance, and installation instructions. Read all the instructions before using the
the washing machine.
Do not wash articles which have been previously cleaned, washed, soaked or treated
with gasoline, dry-cleaning solvents or other inflammable or explosive substances as
they produce vapours that may ignite or explode.
Do not add gasoline, dry-cleaning solvents or other inflammable or explosive
substances to the wash water since they produce vapours which may ignite or
explode.
Do not repair or replace any part of the washer, nor attempt any type of service unless
it has been recommended in the maintenance instructions in the manual.
Do not stand or sit on the machine, or support yourself on the open loading door.
To reduce the risk of fire or electric shock, do NOT use an extension lead or adapter
to connect the washing machine to the mains electricity.
The machine must only be used for what it was designed for.
Follow the washing instructions recommended by the manufacturer of the item to be
washed.
Do not start the washing machine until you have made sure that:
• It has been installed according to the installation instructions.
• All the water, drainage, mains and earth connections comply with local
standards and other applicable standards.
1
t e c h n i c a l
Warnings and precautions
Specifications plate (Registration plate)
This is situated on the hatch on the front of the washing machine. This plate indicates
the following:
Mains electricity grid voltage and frequency
Total power
TYPWM-900E3B
CAPLE 3F-2609
N.050900001
COD.905013069
2200W 220-230V-50Hz
10A.
4.9-98N/cm2
NIF ESF20020517
0905013069050900001
Washing machine code
(9 digits)
Month of manufacture
Year of manufacture
2%')342!4)/.0,!4%
490%/&!00!2!453
-!2+!.$-/$%,
3%2)!,.5-"%2
490%/&!00!2!453
0/7%26/,4!'%!.$&2%15%.#9
#!0!#)49
-!).37!4%202%3352%
/&&)#)!,#%24)&)#!4)/.39-"/,
!.$/4(%23
"!2#/$%
2
t e c h n i c a l
Features
2.- Features
This range is comprised of the following models:
Detergent
drawer
ON/OFF
Programme Start-Pause
button
button selector control
Spin + flot
button
Time delay
button
Additional
functions
button
Select
F7-212
8kg
+
AA
ABS
Turbo Time Plus
1200 r.p.m.
V3 display
Detergent
drawer
ON/OFF
Programme Start-Pause
button selector control
button
Spin + flot
button
Time delay
button
Additional
functions
button
Select
F7-412 X
8kg
+
AA
ABS
Turbo Time Plus
1200 r.p.m.
V4 display
3
t e c h n i c a l
Description of operation
Selecting additional functions
Button for selecting additional functions according to programmes.
a) It has 3 options: easy iron, intensive wash, extra
rinse. Press the select button to display to required
option.
b) By clicking several times you can choose between
various combinations, of one, two, and even three
additional functions at the same time, depending on
the chosen programme.
3ELECT
Key: Easy iron
This option reduces the formation of creases in
garments by performing a special programme with
special movements to fluff up the garments after the
spin and make ironing easier.
3ELECT
Key: Extra rinse
This increases the intensity of the final rinse applied to the clothing. This is
recommended for large loads and garments belonging to users with sensitive skin.
Increases water consumption!
Key: Intensive Wash
This option, specially recommended for very dirty or stained garments, gives better
results by lengthening the wash cycle.
Time delay option
Time delay selection key A delay of up to 24 hours
may be selected. The delay must be selected after
choosing the wash programme.
To select the time delay in hours, press the clock
button. Each press delays the start time by one
hour.
3ELECT
Cancelling time delay To cancel the time delay, press the clock button repeatedly.
The delay will be cancelled by reaching 24 hours and then pressing once more.
Changing to another programme also cancels the delay.
4
t e c h n i c a l
Description of operation
Spin selection
The wash options must always be selected after selecting the wash programme. Any
change of programme during the selection annuls the options which had previously
been selected.
a) Spin selection and anti-crease (flot) button
A
The selected programme has an associated spin
speed in revolutions per minute, as shown on the
screen.
3ELECT
b) This can be modified by pressing the spin button
repeatedly and the spin speed in revolutions will go B
down by 100 each time, until 400.
3ELECT
c) Skip spin option
Press the spin button once more to reach the skip C
spin option. A programme without a final spin is
used to prevent creases from forming when washing
special fabrics.
3ELECT
d) Flot/anti-crease option
This stops at the final rinse, leaving the clothing D
floating in water. When the function is deactivated,
the washing machine continues the programme,
draining and spinning. This is used when you are
not at home, for example, to delay the spin until you
have arrived so that creases are not caused by the
clothes being spun and then left in the drum.
5
3ELECT
t e c h n i c a l
Description of operation
Lock selection
Activate lock
a) Locking is activated by keeping the start/pause
key pressed for at least 3 seconds.
a
The screen will show that it has been activated.
Deactivate lock
b) The lock is deactivated when the wash programme
ends.
b
To unlock before the end of the programme, press
the start key again for at least 3 seconds. After
3 seconds the lock indicator on the screen will
disappear and the machine will be paused.
The ON/OFF button does not deactivate the lock.
Programme ending
When the programme ends the screen will display
0.
Select
When the door is opened or the lock is deactivated
the screen will display 000.
Select
Demo Programme
Press the spin and select buttons simultaneously for at least 3 seconds to activate
and deactivate the DEMO programme.
6
Normal programme
Delicate programmes
Prog. Wool
7
Additional programmes
Fast 30ºC
Normal 30ºC
Normal 40ºC
2
3
4
Delicate cold
Delicate 30ºC
8
9
—
—
—
15 Spin
16 Drainage/End
WOOL 35
Wool 35ºC
13
14 Rinses
WOOL Cold
60
40
30
Cold wool
40
30
cold
60
90
60
40
30
12
11 Delicate 60ºC
10 Delicate 40ºC
Pre-wash 60ºC
Normal 90ºC
7
6
5 (*) Normal 60ºC
cold
Normal cold
1
30
Recommended
temperature
Programme
YES NO
NO
Cotton/mix cotton
Synthetic/Delicate
Wool/wool mix
Cotton/mix cotton
Synthetic/Delicate
Wool/wool mix
Cotton/mix cotton
Synthetic/Delicate
Wool/wool mix
YES NO
Wool/mix wool
white/colour
light soiling
very light soiling
NO
YES
YES
Synthetic/mix
Cotton white/solid colours
Normal soiling
YES
YES
YES
YES
Synthetic/mix
Cotton delicate colours
Normal soiling
YES NO
YES
Synthetic/mix
Cotton delicate colours
Slightly soiled
Wool/mix wool
YES
YES
Cotton/Linen
White
Very dirty
Synthetic/mix
Cotton delicate colours
Very slightly soiled
YES
Cotton/Linen
Solid colours
Normal soiling
YES
YES
Cotton/Linen
Solid colours
Slightly soiled
YES
Cotton/Linen
White/solid colours
Very dirty
YES
YES NO
YES
NO
Anti-crease
Buttons for possible options
Extra
rinse
Intensive
wash
Easy
iron
Select
spin
Skip
spin
Cotton/Linen
delicate colours
slightly soiled
Cotton/Linen
white/coloured
very slightly soiled
Cotton/Linen
delicate colours
very slightly soiled
Type of material
8
8
8
8
8
2
8
8
8
8
2
2
3.5
3.5
3.5
3.5
(Kg)
Máx.load
load
Max.
(Kg
_
_
Wash products
compartiment
Emptying and end of programme.
Takes the programme to the final position
Emptying and long final spin
Rinses, automatic
additive absorption if required,
and long final spin
WOOL wash, rinses,
automatic additive absorption
if required, and gentle final spin
Delicate wash, rinses,
automatic additive absorption
if required, and gentle final spin
Pre-wash, normal wash, rinses,
automatic additive absorption
if required, and long final spin
Normal wash, rinses,
automatic additive absorption
if required, and long final spin
Normal wash, rinses,
automatic additive absorption
if required, and long final spin
SHORT wash, rinses,
automatic additive absorption
if required, and long final spin
Programme Description
0.00/0
0.05/0
0.05/25
0.45/55
0.05/55
1.00/45
0.40/45
0.20/45
0.10/45
1.50/64
2.20/64
1.52/59
0.60/59
0.30/59
0.25/30
0.10/59
2
10
23
40
30
70
55
50
50
100
110
80
57
52
30
50
Approx.
duration
(min.)
TURBO TIME PLUS
Total
consumption
KWh / litres
t e c h n i c a l
Features
Programme tables
t e c h n i c a l
Description of operation
3.- Description of operation
3.1.- General description
3.1.1.- Component characteristics
Component
Motor
1250 RPM
4(%2-)#
02/4%#4/2
2
4'
34!4/2
Double field motor
1400 RPM
4(%2-!,
02/4%#4/2
2
4'
34!4/2
Door lock
Function
Used in machines with
variable spin; makes
rotating movements
when washing and
spinning.
Motor power supply:
- Clockwise, power
220V. , contacts 2 and
3. Bridge between
contacts 5 and 6.
- Anti-clockwise,
power 220V. , contacts
3 and 5. Bridge
between contacts 2
and 6.
Used in machines with
variable spin; makes
rotating movements
when washing and
spinning.
Motor power supply:
- Clockwise, power
220V. , contacts 4 and
5. Bridge between
contacts 3 and 6.
- Anti-clockwise,
power 220V. , contacts
4 and 6. Bridge
between contacts 5
and 3.
Opens and closes
hatch lock.
8
Features
Voltage: 220 v / 50 Hz
Stator resistance: 1.3 Ω
Rotor resistance: 1.7 Ω
Tachogenerator resistance:
184 Ω
Tachogenerator voltage: 1.2
v / 1,000 rpm
Voltage: 220 v / 50 Hz
Stator resistance: 3.3 Ω
Rotor resistance: 2.46 Ω
Tachogenerator resistance:
90 Ω
Voltage: 220 v / 50 Hz
16 Amp.
Between 40 and 75
seconds delay.
t e c h n i c a l
Description of operation
Component
Door lock with instant
opening
Function
Hatch closing
Manual opening for use
in case of electricity
supply failure.
Features
Recirculation pump
Re-circulates the drum
water for greater wash
effectiveness and
reduced programme
times.
Voltage: 220-240 V /50 Hz
Drainage pump resistance
170 Ω
Recirculation pump
resistance 180 Ω
Both with thermal protector.
Power 30 (W)
Doubly connected
electrically operated
valve
Allows water intake in
the pre-wash, wash and
rinse phases.
EV1 pre-wash orange
connector
EV2 wash black
connector
EV1 + EV2 additive
intake
Voltage: 220-240 V /50 Hz
Power: 5 W
Flow: 6.7 litres/ minute
Pressure: 0.5-10 kg / cm²
Resistance: R1=R2=R3=
3.7 KΩ
3/4 Thread Gas
12mm conduit diameter
Pressure switch
The pressure gauge
is activated in the
following conditions:
- When the wash level
reaches 12 litres.
(11-12)
- When the level
exceeds 33 litres
(overflow), the drainage
pump is activated
(safety).
(11-16)
- The rinse level is
performed according
to the time of the
microprocessor of the
electronic card.
Level 1
102 / 72 ± 3
9
Overflow safety device
310 ± 10
12
11
14
16
11 Common
12 Water intake
14 Heating
16 Overflow
t e c h n i c a l
Description of operation
Componente
Heating resistance
Function
Heating element +
thermal fuse incorporated into the element
itself
Thermal fuse cut-out
temperature165º
V3 electronic circuit
Power and display
circuit
V4 electronic circuit
Power and display
circuit
10
Features
Resistance: 26.4 Ω
Material: Austenitic
stainless steel
Power: 2022 W
Voltage: 230 v
NTC ≤ 30ºC variable
resistance value 9786 Ω
Voltage: 220 v / 50 Hz
Important: It is necessary
to configure the circuit
before starting the machine.
(Follow configuration
instructions)
Voltage: 220 v / 50 Hz
Important: It is necessary
to configure the circuit
before starting the machine.
(follow configuration
instructions)
t e c h n i c a l
Description of operation
3.1.2.- V3 and V4 circuit configuration
If the circuit is not configured it will go into status as soon as it is plugged in (go to
step no. 7) If the circuit is configured it enters the current configuration. To change the
configuration, follow these steps:
1.- Turn the machine off
2.- Press the start / pause button
3.- Press the button
and keep it pressed (until step 5)
for 1 second until the LCD screen lights up
4.- Press the spin button
the LCD screen
and wait 2 seconds until the letter
is displayed on
5.- Release all keys simultaneously
6.- The door lock will be locked
7.- Press the spin button
(the last digit of the LCD will flash).
8.- Pressing the CLOCK button changes the parameter to be adjusted, starting with
the KG digit and following the sequence KG – RPM – RECIRCULATION – HOT
WATER – DOOR OPENING – KG….
Pressing the SPIN button changes the value of the parameter; the possible values
are limited to the circuit’s hardware reference and the selected KGs.
If the KGs are changed after having selected the RPM and the previous RPM value is
not permitted for the newly selected KGs, the RPM will re-adjust to the value closest
to the newly selected KGs.
Select
RPM
RECIRCULATION PUMP COLD WATER
YES
/NO
YES
/NO
11
Select
DOOR OPENING
YES
/NO
KG
t e c h n i c a l
Description of operation
KG – Drum capacity
1
7: 7 kg
8: 8 kg
KG options depending on circuit references /
washing machine model.
R.P.M. (Revolutions per minute)
These values depend on the hardware
reference and the KGs selected.
RECIRCULATION
0: WITHOUT Recirculation Pump
00: WITH Recirculation Pump
If the circuit does not have this option it will
always be 0.
HOT WATER
0: Cold water
8: Hot water
If the circuit does not have this option it will
always be 0.
4
DOOR OPENING
2 0: WITHOUT door opening
8 : WITH instant door opening
If the circuit does not have this option it will
always be 0.
Circuit validation (see table 1)
3 Once the circuit has been configured it is
confirmed by pressing the start/pause button for
3 sec. until the digits stop flashing. After 3 sec. it
exits the configuration process, entering the TSS
programme (See table 1)
5
6
• Fagor T.S.S. Programme
In order to check the operation of the washing machine’s electric components, select
the T.S.S. programme by following these steps:
1.- General ON / OFF switch (LCD off)
2.- Press the start / pause button and keep it pressed
3.- Hold down the ON/OFF switch until the LCD screen lights up.
4.-Press and hold down the select spin button and wait approx. 2/ 3 sec. until the
letter
is displayed on the screen
5.- Release all buttons simultaneously
6.- Press the spin button and wait until the digits on the screen (LCD) appear (the last
button on the right flashes).
7.- Press and hold down the start / pause button
are flashing.
until all the digits on the screen
8.- The number 1 will be displayed on the screen – then follow the instructions in table
1, below.
DISPLAY
SELECTION MODE
TIME (APROX.)
1
Water intake via Pre-wash Electrovalve + Movement of wash
motor at 55 rpm
10 seconds
2
Emptying + Spin
5 min.
3
Water inlet via the electronic valve for washing until wash level is
reached
Pressure switch
level
4
The resistance starts to heat up until it reaches 40ºC +
Intermittent recirculation 90 sec. without being activated and 30
sec. activated
40ºC
5
Water input via pre-wash, wash and softener electrically operated
valve + Recirculation
5 seconds
Pump empty
30 seconds
12
t e c h n i c a l
Description of operation
Label location: It is located in the detergent drawer.
Select
F7-412 X
8kg
+
AA
ABS
Turbo Time Plus
R.P.M. 1200
XXXXXXX
1200 r.p.m.
R
(00)
AF (0) Cold water
AF
AP: Does not have instant door
opening
AP
(0)
(0)
LF5S017A3
R (00) With recirculation
REFERENCE BARCODE
CONTROL PANEL
(COD. 39)
12
XXXX
8
KG. 8 Kg.
F-2812
To display the washer
configuration:
1º Configure Kg.
2º Configure R.P.M.
3º Configure Recirculation
4º Configure Cold water
5º Configurar Door opening
Press the START button for
3 seconds and the screen
displays:
Select
F7-212
8kg
+
AA
ABS
Turbo Time Plus
R
(00)
AF (0) Cold water
AF
AP: Has instant door opening
AP
(0)
(8)
8
KG. 8 Kg.
XXXXXXX
LF5S004X7
R (00) With recirculation
12
F-4812 X
13
XXXX
R.P.M. 1200
CODIGO DE BARRAS REFERENCIA
PORTAMANDOS
(COD. 39)
1200 r.p.m.
To display the washer
configuration:
1º Configure Kg.
2º Configure R.P.M.
3º Configure Recirculation
4º Configure Cold water
5º Configure Door opening
Press the START button for 3
seconds and the screen displays:
The fault is displayed:
If the pressure switch detects that the washing machine is too full
If the pump connector is broken or is not connected
OVERFULL (F07)
14
In version V1 nothing happens
In versions V3 and V4 the washing machine stops
(Programme end)
ACTION
The washing machine spins at the lowest speed
While communicating with a washing machine a BMF fault is detected. In order to detect it, the following
must happen:
- Display board: If the board does not receive the correct message (can be checked in the BMF variable
“SinTraficoEnBus==1”)
from the power board for more than 10 seconds, or if it is continually receiving LINK messages but not data
(no status
messages. (Can be checked in the BMF by its meaning “TramaDatosATratar==0”) for more than 10
seconds, the fault F12 will be displayed.
- Power board: If the power board is continually sending LINK messages to the display board for more than
10 seconds (the master can recognise and check the BMF variable “EtadoLinkNodos”), the F12 fault is
then displayed and should be activated in the master. If the power board receives a correct message from
the display board (Link_Response or Data) the F12 fault is reset
CHECK
If an imbalance is detected when it makes 18 attempts to spin or during 15 minutes of
attempts
IMBALANCE
(C03)
WARNING
The fault is reset in the following manner:
1.- Cutting off the power (unplug or ON/OFF)
2.- Change the selector position
RESET
‘-Power Board: If the Power Board receives a correct message
(Link_Response or Data) from the Display Board, the F12 and the
related 10sec timer have to be reset.
‘- Display Board: Ihe fail and the related 10sec timer have to be
reset when a correct data frame (identification or status frame) is
received by the Display Board from the Power Board.
See BMF document
In V1 nothing happens
In versions V3 and V4 the “@” symbol and the lock symbol
will flash intermittently
While communicating with the washing machine it is detected that a node is absent
EXTERNAL DOMOTIC
FAULT (F11)
BMF BUS FAULT
(F12)
See domotic document
In V1 nothing happens
In V3 and V4 the “@” symbol will flash intermittently
Communication between the micro and the bus fails
See domotic document
The same as the previous ones but with the door lock activated
INTERNAL DOMOTIC
FAULT (F10)
Door lock always activated
STOP (Programme end)
The drum rotation direction does not change until the motor stops
(max. time 2 min.)
Tachogenerator failure, motor blocked
- The wash programme is stopped for 120 seconds
- The error counter starts counting
- If the error counter counts 3 faults the error code F08 is displayed
- When the stop time is exceeded the programme begins again
If the error does not occur in the next 20 seconds the error counter is reset. The programme stops (in any
instance) and starts again in the same position. If the error occurs in the spin phase the programme will
start the whole spin sequence again from the start.
This error returns to the initial conditions if the error is reset.
ß < 5°C/15 min. (Except in reliability program)
All options are reset if:
1 – Power is lost (unplug or ON/OFF)
2 - Selector position changed
All options are reset if:
1.- Power is lost (unplug or ON/OFF)
2.- Selector position changed
3.- Door is closed
(IF THE CIRCUIT IS IN A SPECIAL PROGRAMME (AP_01, AP_
01, REP_01 OR SAT) WHEN RESET IT RETURNS TO STATUS A)
All options are reset if:
1 – Power is lost (unplug or ON/OFF)
2.- Selector position changed
3.- If, when the programme finishes, the start button is pressed
RESET (security end)
MOTOR INVERSION
FAULT (F09)
MOTOR
(F08)
DOES NOT HEAT
(F06)
NTC
(F05)
The programme ends without heating the water
STOP (Programme end)
EB ON 6 min. and PN ON (full)
EMPTYING (F02)
NTC in short circuit or open circuit
IN USER PROGRAMME
STOP (Programme end)
- Washing machines with instant opening door lock:
At the beginning of the programme the circuit detects that the door is not closed
Washing machines with PTC door lock:
If the door lock is without power for 8
seconds the fault is displayed
FILLING
(F01)
DOOR OPEN (F04)
ACTIONS
The machine stops with the door lock activated
FAULTS
T.S.S. programme fast forward function: Press the start / pause button to move to another programme step without having to execute the step condition.
EV activated for 8 min. and without water (except in the programme)
SAFETY
MECHANISMS
t e c h n i c a l
Description of operation
Fault modes description table
t e c h n i c a l
Description of operation
The speeds allowed for the V3 circuits depend on the hardware reference (with/without
double field) and the washing machine capacity (in kg), and are as follows:
RPM
DOUBLE FIELD MOTOR
5 kg 700 800 900 1000 1100 ----------6 kg 700 800 900 1000 1100 1200 1300 1400 ----7 kg 700 800 900 1000 1100 1200 1300 1400 1500 1600
Once the circuit has been configured, it is confirmed by pressing the ON button for
3 seconds, which is when the selected code will appear in the LCD for 3 seconds
without flashing, exiting the configuration process.
The speeds allowed for the V4 circuits depend on the hardware reference (with/without
double field and FC) and the washing machine capacity (in kg), and are as follows:
MOTOR 1250
DOUBLE FIELD MOTOR
6 kg 700 800 900 1000 1100 1200 1300 1400 ----7 kg 700 800 900 1000 1100 1200 1300 1400 1500 1600
FC (MOTOR CONVERTER)
6 kg 1300 1400 --------7 kg 1300 1400 1500 1600 1700 1800
15
4336)"2!4)/.
16
3%#
3%#
3%-)$%,)#!4%6)"2!4)/.
3%#
3%#
#,/#+7)3%
350%26)"2!4)/.
./2-!,6)"2!4)/.
./.$%4%#4)/./&
/6%2&,/7!2%!
3%# !.4)#,/#+7)3%
3%-)$%,)#!4%6)"2!4)/.
&,/46)"2!4)/.MAXTIMEHOURS
%842!6)"2!4)/.
3%#
6%29$%,)#!4%6)"2!4)/.
3%#
3%#
0,536)"2!4)/.
t e c h n i c a l
Description of operation
3.1.3.- Washing machine vibrations
• Wash vibrations
)-"!,!.#%4%34AND
)-"!,!.#%4%34AND
0(!3%%!39)2/.
)-"!,!.#%4%34
0(!3%%!39)2/.
./2-!,30).!.$%!39)2/.%,%#42/.)#7!3().'-!#().%3%
)-"!,!.#%4%34
0(!3%%!39)2/.
-!#().%-/$%,
203%,%#4/2
Easy iron
0(!3%%!39)2/.
t e c h n i c a l
Description of operation
• Spin vibrations
17
18
3TEP
3TEP
3TEP
3TEP
3TEP
3TEP
3TEP
3TEP
)-"!,!.#%4%34
0(!3%./2-!,30).
$EPENDINGON
THEPROGRAMME
3%#
20-3%,%#4/2
0/3)4)/.3
t e c h n i c a l
Description of operation
Normal spin:
t e c h n i c a l
Description of operation
3.1.4.- Description of the operation of programme no. 2
Programme no. 2 is a short (quick) programme which takes 30 minutes and heats to
30ºC.
It is a suitable programme for a technician making any operational checks.
The programme phases and their approximate start and end times are described
below.
Pre-wash phases
Wash phase
30’
Rinse phase
13’ 13’
Spin
8’ 8’ 3’ 1’
Drain
+
Spin
Water intake
Heating to
30ºC
End of Heating
Spin
1st Rinse
+
Spin
2nd Rinse
+
Softener
Untangle clothes
Note: When the LCD screen shows 000, the door lock is de-activated
19
0
t e c h n i c a l
Description of operation
3.1.5.- Attempts to spin
If the washing machine detects unbalanced clothes in the spin cycle it will follow this
process:
The total number of attempts to start spinning is 20, divided according to these
criteria.
In the first 6 attempts, the maximum unbalanced limit allowed is 550g.
From the 7th to 18th attempts the maximum unbalanced limit allowed is 800g and
the final speed is less than the nominal speed, for example a 1,200 r.p.m. washing
machine will spin at 1,000 r.p.m.
For the 19th and 20th attempts, the maximum unbalanced limit allowed is 1,500 g.,
and the final spin speed will be 650 r.p.m., except in washing machines with a nominal
speed of 700 r.p.m., which will spin at 400 r.p.m.
This number of attempts to reposition the clothes in the drum will increase the total
programme time by 20 minutes.
At the end the LCD screen will display CO3. This is not considered a fault as it warns
the user about the security measure the circuit has detected.
If an imbalance is detected in the rinse phase, the number of attempts will not exceed
3.
20
t e c h n i c a l
Description of operation
Only for hot water
3.2.- Drawings and diagrams
21
t e c h n i c a l
FILTER
E.V. 2 WASH
E.V. 1 PRE-WASH
E.V. 3 HOT WATER
PRESSURE SWITCH
ELEMENT
FUSE
DRAIN
PUMP
DOOR LOCK
RECIRCULATION
PUMP
CONTROL PANEL
CONTROL PANEL
CONTROL PANEL
Description of operation
Reference electric installation cold water with recirculation LH6J200A6.
22
Open as PDF
Similar pages