Adam Equipment
PTS SERIES
With AE402 Indicator
(P.N. 3106610715, Revision E, April 2011)
Adam Equipment 2011 ©
Adam Equipment 2011 ©
Thank you for purchasing the ADAM PTS Pallet Truck.
For your safety and correct operation, please read the following instructions
carefully before using it.
CONTENT
1.0
2.0
3.0
4.0
5.0
6.0
SAFETY ............................................................................................................................. 3
INSTRUCTION .................................................................................................................. 5
2.1 SPECIFICATIONS ......................................................................................................... 5
2.2 PACKING LIST.............................................................................................................. 5
INSTALLATION.................................................................................................................. 8
3.1 AE 402 ASSEMBLY .................................................................................................... 10
CALIBRATION ................................................................................................................. 13
TROUBLE SHOOTING .................................................................................................. 14
MAINTENANCE .............................................................................................................. 15
1
Adam Equipment 2011 ©
2
Adam Equipment 2011 ©
1.0
SAFETY
• To prevent damage to the scale, please read these operating instructions thoroughly.
• When using the pallet truck, please keep the handle in the DRIVE position.
• This pallet truck must be operated by trained personnel only.
• Check the pallet truck first before using it making sure that the wheels, handles and forks
are fitted correctly and secure
• Avoid unsuitable and uneven floor surfaces
• Please wear protective clothing where necessary
• Allow 60cm clearance from the pallet truck when operating.
• Pay attention and focus on the object you are lifting
• Do not overload.
3
Adam Equipment 2011 ©
4
Adam Equipment 2011 ©
2.0
INSTRUCTION
2.1
SPECIFICATIONS
Common specifications
Model
PTS 2000
PTS 5000a
Load cell Capacity
2000 kg
5000Lb
Resolution
0.5 kg
1Lb
Fork length
1150mm
Fork Width (each)
160mm
(6.3”)
160mm
(6.3”)
Fork Width (total)
540mm
(21.25”)
680mm
(26.77”)
Fork Height
77mm increasing to 192mm
77mm increasing to 192mm
(3” – 7.5”)
(3” – 7.5”)
125 kg (275 Lb)
135 kg (297 Lb)
Net Weight
(45.25“)
1220mm
(48”)
See the User Manual for the Indicator supplied with the PTS for more
information about the weighing features and operation.
2.2
PACKING LIST
Part No.
3101410695
301177255
3106610715
3101010700
3101710929
3101710930
3101711228
3101210931
2100010935
3104010713
Part name
Indicator mounting bracket, upper
M4 x 6 SS Soc Head cap Screw din912-A2
PTS Manual/Instructions
M4 Allen key
Roller pin φ 20 x 86
Spring pin φ 5 x32
Split Pin φ5×50(galvanized)
Handle
AE402 indicator assembly
AE402 load cell cable
5
QTY
1
4
1
1
1
1
1
1
1
1
Adam Equipment 2011 ©
6
Adam Equipment 2011 ©
7
Adam Equipment 2011 ©
3.0
INSTALLATION
Please follow the installation instructions to ensure correct operation of your
PTS. In transportation the handle is removed from the truck, this needs to be
installed following the instructions below:
NOTE: Do not lower the handle down fully until completing the instructions
below.
1) Insert the roller pin into the hole of roller rack, securing the handle to the
frame.
2) Fit the split pin through the holes provided.
3) Pass the chain through the center hole of the roller pin. Secure the end of
the chain to the slot on the end of the unloading plate.
4) Remove the transit rod before use. Press the handle down only far enough to
release any pressure on the transit rod, then pull the transit rod free.
8
Adam Equipment 2011 ©
9
Adam Equipment 2011 ©
3.1
AE 402 ASSEMBLY
Rear view of AE 402 Indicator
Fit the PTS to Indicator cable as shown in the picture below:
5 pin connector
fitted here
10
Adam Equipment 2011 ©
The Indicator bracket is fitted to the PTS using 4 x M4 screws as the picture
below shows, these should be tightened using the Allen Key supplied .
M4 x 6 Screws
4 places
The Indicator cable goes through the hole on the bracket and connects to the
Indicator using the 7 pin connector.
7 pin connector
fitted here.
11
Adam Equipment 2011 ©
The AE 402 indicator is placed into the mounting bracket, and secured using
the two plastic fasteners as shown below:
Plastic fasteners used to
secure Indicator to the
bracket.
12
Adam Equipment 2011 ©
4.0
CALIBRATION
The PTS is factory calibrated, please refer to the user manual for the indicator
supplied (AE 402) when further calibration when required.
13
Adam Equipment 2011 ©
5.0
TROUBLE SHOOTING
No.
Problem
Cause
Solution
Forks cannot ascend
1
2
3
4
5
to the maximum
Inadequate hydraulic oil in the chamber.
Refill oil chamber. See Figure 1.
No hydraulic oil.
Refill oil chamber. See Figure 1 .
Oil is not clean.
Change oil
height
Forks can not be
raised
Forks can not
Position of the goods are to one side of the truck
descend
Relocate load.
.
Oil spillage
Aging or damaged seals.
Call for Service.
Forks descend when
The oil could be unclean
Change the oil.
the trigger is not in
Some parts of the hydraulic system are damaged.
Vent the air.
descend position
Call for Service.
Fig 1
14
Adam Equipment 2011 ©
6.0
MAINTENANCE
• Please check the oil every six months , we suggest you use hydraulic oil: ISO
VG32
• Whilst in transit air may enter into the hydraulic pump, this may result in the
forks not raising when first used. Please move the handle up and down
several times to allow air to escape.
• Routine maintenance is necessary. You should focus on the wheels and
handle assemblies. When the truck is not in use, remove the items on the
forks, and reset the forks to their lowest position.
• All the bearings and axles have been lubricated, please check at regular
intervals
15
Adam Equipment 2011 ©
16
Adam Equipment 2011 ©
Manufacturer’s Declaration of Conformity
This product has been manufactured in accordance with the harmonised European standards, following the
provisions of the below stated directives:
Electro Magnetic Compatibility Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
Adam Equipment Co. Ltd.
Bond Avenue, Denbigh East
Milton Keynes, MK1 1SW
United Kingdom
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. The
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Shielded interconnect cables must be employed with this equipment to insure compliance with the pertinent
RF emission limits governing this device.
Changes or modifications not expressly approved by Adam Equipment could void the user's authority to
operate the equipment.
WEEE COMPLIANCE
Any Electrical or Electronic Equipment (EEE) component or assembly of parts intended to be incorporated
into EEE devices as defined by European Directive 2002/95/EEC must be recycled or disposed using techniques
that do not introduce hazardous substances harmful to our health or the environment as listed in Directive
2002/95/EC or amending legislation.
Battery disposal in Landfill Sites is more regulated since July 2002 by
regulation 9 of the Landfill (England and Wales) Regulations 2002 and Hazardous Waste Regulations 2005. B
are set to impose targets for
Adam Equipment 2011 ©
ADAM EQUIPMENT is an ISO 9001:2008 certified global organisation with more than 30
years experience in the production and sale of electronic weighing equipment. Products are
sold through a world wide distributor network supported from our company locations in the
UK, USA, SOUTH AFRICA and AUSTRALIA.
ADAM’s products are predominantly designed for the Laboratory, Educational, Medical and
Industrial Segments. The product range is as follows:
-Analytical and Precision Laboratory Balances
-Counting Scales for Industrial and Warehouse applications
-Digital Weighing/Check-weighing Scales
-High performance Platform Scales with extensive software
features including parts counting, percent weighing etc.
-Crane scales for heavy-duty industrial weighing
-Digital Electronic Scales for Medical use
-Retail Scales for Price computing
© Copyright by Adam Equipment Co. Ltd. All rights reserved. No part of this
publication may be reprinted or translated in any form or by any means without the
prior permission of Adam Equipment.
Adam Equipment reserves the right to make changes to the technology, features,
specifications and design of the equipment without notice.
All information contained within this publication is to the best of our knowledge
timely, complete and accurate when issued. However, we are not responsible for
misinterpretations which may result from the reading of this material.
The latest version of this publication can be found on our Website.
Visit us at www.adamequipment.com
Adam Equipment 2011 ©
Open as PDF
Similar pages