S9 Escape Auto™ S9 Escape Auto indications for use

368876.book Page 1 Thursday, October 11, 2012 2:20 PM
S9 Escape Auto™
POSITIVE AIRWAY PRESSURE DEVICE
Information Guide
English
English
S9 Escape Auto indications for use
The S9 Escape Auto self-adjusting system is indicated for the treatment of obstructive sleep apnea
(OSA) in patients weighing more than 30 kg. The S9 Escape Auto self-adjusting system is intended for
home and hospital use.
Contraindications
Positive airway pressure therapy may be contraindicated in some patients with the following preexisting conditions:
• severe bullous lung disease
• pneumothorax
• pathologically low blood pressure
• dehydration
• cerebrospinal fluid leak, recent cranial surgery, or trauma.
Adverse effects
Patients should report unusual chest pain, severe headache, or increased breathlessness to their
prescribing physician. An acute upper respiratory tract infection may require temporary discontinuation
of treatment.
The following side effects may arise during the course of therapy with this device:
• drying of the nose, mouth, or throat
• nosebleed
• bloating
• ear or sinus discomfort
• eye irritation
• skin rashes.
1
368876.book Page 2 Thursday, October 11, 2012 2:20 PM
Troubleshooting
If there is a problem, try the following suggestions. If the problem cannot be solved, contact your
equipment supplier or ResMed. Do not attempt to open this device.
Problem/Possible cause
Solution
No display
Power is not connected.
The DC plug is partially inserted into
the back of the device.
Ensure the power cable is connected and the power outlet (if
available) is on.
Fully insert the DC plug.
Insufficient air delivered from the device
Ramp time is in use.
Air filter is dirty.
Air tubing is not connected properly.
Air tubing is blocked, pinched or
punctured.
Mask and headgear are not
positioned correctly.
Incorrect air tubing selected.
Wait for air pressure to build up or change ramp time.
Replace air filter.
Check air tubing.
Unblock or free the air tubing. Check the air tubing for
punctures.
Adjust position of mask and headgear.
If you are using the SlimLine or Standard air tubing ensure
that you have the correct air tubing selected via the menu.
Pressure rises inappropriately
Talking, coughing or breathing in an
unusual manner.
Mask cushion is buzzing against the
skin.
Avoid talking with a nasal mask on, and breathe as normally
as possible.
Adjust the headgear.
Displays error message: High temperature fault, refer to user manual
Device has been left in a hot
environment.
Air filter is blocked.
Air tubing is blocked.
2
Allow to cool before re-use. Disconnect the power cord and
then reconnect it to restart the device.
Replace your air filter. Disconnect the power cord and then
reconnect it to restart the device.
Check your air tubing and remove any blockages. Disconnect
the power cord and then reconnect it to restart the device.
368876.book Page 3 Thursday, October 11, 2012 2:20 PM
Problem/Possible cause
Solution
Humidifier setting is too high,
resulting in accumulation of water in
the air tubing.
Turn the humidifier setting down and empty the water from
the air tubing.
Displays error message: Check ResMed 30/90W Power Supply Unit and fully insert the
connector
The DC plug is partially inserted into
the back of the device or inserted too
slowly.
A non-ResMed power supply unit is
connected to the device.
The power supply unit is being
covered by bedding.
Fully insert the DC plug.
Remove the power supply unit and replace with a ResMed
power supply unit.
Make sure that the power supply unit is free from bedding,
clothes or other objects that could cover it.
Displays error message: Tube blocked, please check your tube
Air tubing is blocked.
Check your air tubing and remove any blockages.
Displays error message: High leak, please check system setup and all connections
There is excessive leak.
Adjust position of mask and headgear.
Air tubing is not connected properly. Connect firmly at both
ends.
The following message is displayed on the LCD after you try to update settings or copy data to
the SD card: Card error, please remove SD card and contact service provider
SD card is not inserted correctly.
You may have removed the SD card
before settings were copied to the
CPAP device.
Ensure that the SD card is inserted correctly.
Reinsert the SD card and wait for the home screen or the
Settings updated successfully, press any key message
to appear on the LCD.
Note: This message only appears once. If you re-insert the
SD card after you have updated your settings, the message
will not be re-displayed.
The following message is NOT displayed on the LCD after you try to update the settings using
the SD card: Settings updated successfully, press any key
The settings were not updated.
Contact your clinician/service provider immediately.
3
368876.book Page 4 Thursday, October 11, 2012 2:20 PM
Technical specifications
Operating pressure range
4 to 20 cm H2O
Maximum single fault steady state
30 cm H2O
pressure
Pressure measurement tolerance
±0.5 cm H2O ± 4% of the measured reading
Flow measurement tolerance
±6 L/min or 10% of reading, whichever is greater
DECLARED DUAL-NUMBER NOISE EMISSION VALUES in accordance with ISO 4871:
Sound pressure level
24 dBA as measured according to ISO 17510-1:2002
26 dBA with uncertainty of 2 dBA as measured according to
ISO 17510-1:2007
Sound power level
34 dBA with uncertainty of 2 dBA as measured according to
ISO 17510-1:2007
Nominal dimensions (L x W x H)
153 mm x 140 mm x 86 mm
Weight
835 g
90W power supply unit
Input range 100–240V, 50–60Hz,
Nominal for aircraft use 115V, 400Hz
Typical power consumption 70W (80VA)
Maximum power consumption 110W (120VA)
30W power supply unit
Input range 100–240V, 50–60Hz,
Nominal for aircraft use 115V, 400Hz
Typical power consumption 20W (40VA)
Maximum power consumption 36W (75VA)
Operating temperature
+5ºC to +35ºC
Note: The air flow for breathing produced by this therapy
device can be higher than the temperature of the room.
Under extreme ambient temperature conditions (40ºC) the
device remains safe.
Operating humidity
10–95% non-condensing
Operating altitude
Sea level to 2,591 m
Storage and transport temperature
-20ºC to +60ºC
Storage and transport humidity
10–95% non-condensing
Housing construction
Flame retardant engineering thermoplastic
Supplemental oxygen
Recommended maximum supplemental oxygen flow:
4 L/min
4
368876.book Page 5 Thursday, October 11, 2012 2:20 PM
Hypoallergenic air filter
Standard air filter
SlimLine™ air tubing
Standard air tubing
ClimateLine™ heated air tubing
ClimateLineMAX™ heated air tubing
Air outlet
Electromagnetic compatibility
Aircraft use
IEC 60601-1 classification
Non-woven acrylic and polypropylene fibers with
polypropylene carrier
Polyester fiber
Flexible plastic, 1.8 m, 15 mm inner diameter
Flexible plastic, 2 m, 19 mm inner diameter
Flexible plastic and electrical components,
2 m, 15 mm inner diameter
Flexible plastic and electrical components,
1.9 m, 19 mm inner diameter
The 22 mm conical air outlet complies with ISO 5356-1
Product complies with all applicable electromagnetic
compatibility requirements (EMC) according to IEC60601-12, for residential, commercial, and light industry
environments.
It is recommended that mobile communication devices are
kept at least 1 m away from the device.
Information regarding the electromagnetic emissions and
immunity of this ResMed device can be found on
www.resmed.com, on the Products page under Service
and Support. Click on the PDF file for your language.
ResMed confirms that the S9 Escape Auto meets the
Federal Aviation Administration (FAA) requirements (RTCA/
DO-160) for all phases of air travel.
Class II (double insulation), Type BF
Notes:
• The manufacturer reserves the right to change these specifications without notice.
• The temperature and relative humidity settings displayed for ClimateLine or ClimateLineMAX are not
measured values.
• Check with your clinician/service provider before using the SlimLine air tubing with devices other
than the S9.
5
368876.book Page 6 Thursday, October 11, 2012 2:20 PM
Pneumatic flow path
S9 Escape Auto
H5i
Blower
Mask
Inlet filter
Tube
Symbols
The following symbols may appear on your S9, power supply unit, air tubing or packaging.
Caution;
Read instructions before use;
against vertically dripping water;
Start/Stop;
RoHS;
IP20 Not drip proof;
Manufacturer;
Batch code;
Lock/unlock;
IP21 Protection against the insertion of fingers and
Type BF equipment;
Class II equipment;
European Authorised Representative;
Catalogue number;
China pollution control logo 1;
Serial number;
European
Direct current;
China pollution control logo 2;
Keep Dry
Environmental information
WEEE 2002/96/EC is a European Directive that requires the proper disposal of electrical and electronic
equipment. This device should be disposed of separately, not as unsorted municipal waste. To dispose
of your device, you should use appropriate collection, reuse and recycling systems available in your
region. The use of these collection, reuse and recycling systems is designed to reduce pressure on
natural resources and prevent hazardous substances from damaging the environment.
If you need information on these disposal systems, please contact your local waste administration. The
crossed-bin symbol invites you to use these disposal systems. If you require information on collection
and disposal of your ResMed device please contact your ResMed office, local distributor or go to
www.resmed.com/environment.
6
368876.book Page 7 Thursday, October 11, 2012 2:20 PM
Servicing
The S9 device is intended to provide safe and reliable operation when operated in accordance with the
instructions provided by ResMed. ResMed recommends that the S9 be inspected and serviced by an
authorised ResMed Service Centre if there is any sign of wear or concern with device function.
Otherwise, service and inspection of the devices generally should not be required during the five year
design life of the device.
Limited warranty
ResMed Ltd (hereafter ’ResMed’) warrants that your ResMed product shall be free from defects in
material and workmanship from the date of purchase for the period specified below.
Product
• Mask systems (including mask frame, cushion, headgear and tubing)—
excluding single-use devices
• Accessories—excluding single-use devices
• Flex-type finger pulse sensors
• Humidifier water tubs
• Batteries for use in ResMed internal and external battery systems
• Clip-type finger pulse sensors
• CPAP and bilevel device data modules
• Oximeters and CPAP and bilevel device oximeter adapters
• Humidifiers and humidifier cleanable water tubs
• Titration control devices
• CPAP, bilevel and ventilation devices (including external power supply units)
• Battery accessories
• Portable diagnostic/screening devices
Warranty
period
90 days
6 months
1 year
2 years
This warranty is only available to the initial consumer. It is not transferable.
If the product fails under conditions of normal use, ResMed will repair or replace, at its option, the
defective product or any of its components.
This limited warranty does not cover: a) any damage caused as a result of improper use, abuse,
modification or alteration of the product; b) repairs carried out by any service organisation that has not
been expressly authorised by ResMed to perform such repairs; c) any damage or contamination due to
cigarette, pipe, cigar or other smoke; and d) any damage caused by water being spilled on or into an
electronic device.
Warranty is void on product sold, or resold, outside the region of original purchase. Warranty claims on
defective product must be made by the initial consumer at the point of purchase. This warranty replaces
7
368876.book Page 8 Thursday, October 11, 2012 2:20 PM
all other expressed or implied warranties, including any implied warranty of merchantability or fitness
for a particular purpose. Some regions or states do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. ResMed shall not be responsible for any incidental
or consequential damages claimed to have resulted from the sale, installation or use of any ResMed
product. Some regions or states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from region to region. For further information on your
warranty rights, contact your local ResMed dealer or ResMed office.
WARNINGS
•
•
•
•
•
•
•
•
•
Read the entire manual before using the device.
Use the device only as directed by your physician or healthcare provider.
Use the device only for the intended use as described in this manual. Advice contained in this
manual should not supersede instructions given by the prescribing physician.
If you notice any unexplained changes in the performance of the device, if it is making unusual or
harsh sounds, if the device or the power supply are dropped or mishandled, if water is spilled into the
enclosure, or if the enclosure is broken, discontinue use and contact your ResMed Service Center.
Beware of electrocution. Do not immerse the device, humidifier, power supply or power cord in
water. In the event of a spill, disconnect the device from the power supply and let the parts dry.
Always unplug the device before cleaning and make sure that all parts are dry before plugging in the
device.
Explosion hazard—do not use in the vicinity of flammable anesthetics.
Make sure the power cord and plug are in good condition and the equipment is not damaged.
Keep the power cord away from hot surfaces.
The device should only be used with masks (and connectors1) recommended by ResMed, or by a
physician or respiratory therapist. A mask should not be used unless the device is turned on. Once
the mask is fitted, ensure that the device is blowing air. The vent hole or holes associated with the
mask should never be blocked.
Explanation: The device is intended to be used with special masks (or connectors) which have vent
holes to allow continuous flow of air out of the mask. When the device is turned on and functioning
properly, new air from the device flushes the exhaled air out through the mask vent holes. However,
when the device is not operating, insufficient fresh air will be provided through the mask, and the
exhaled air may be rebreathed. Rebreathing of exhaled air for longer than several minutes can, in
some circumstances, lead to suffocation. This applies to most models of CPAP or bilevel devices.
1.
8
Ports may be incorporated into the mask or in connectors that are near the mask.
368876.book Page 9 Thursday, October 11, 2012 2:20 PM
•
•
•
•
•
•
•
•
•
Oxygen supports combustion. Oxygen must not be used while smoking or in the presence of an
open flame.
Always ensure that the device is turned on and airflow generated before the oxygen supply is
turned on. Always turn the oxygen supply off before the device is turned off, so that unused oxygen
does not accumulate within the device enclosure and create a risk of fire.
Do not leave long lengths of air tubing around the top of your bed. It could twist around your head or
neck while you are sleeping.
Do not use electrically conductive or antistatic air tubings.
Do not use the air tubing if there are any visible signs of damage.
Only ResMed air tubing and accessories should be used with the device. A different type of air
tubing or accessory may alter the pressure you actually receive, reducing the effectiveness of the
treatment.
Only use the ResMed 90W or 30W power supply unit. Use the 90W power supply unit to power
the system comprising the device, H5i, air tubing, DC/DC converter and battery pack. The 30W
power supply unit is designed to power the device only and recommended for traveling.
Only ResMed products are designed to be connected to the module connector port. Connecting
other devices could damage the device.
Blocking the air tubing and/or air inlet of the device while in operation could lead to overheating of
the device.
CAUTIONS
•
•
•
•
•
•
Do not open the device enclosure. There are no user serviceable parts inside. Repairs and servicing
should only be performed by an authorised ResMed service agent.
Do not use bleach, chlorine, alcohol, or aromatic-based solutions, moisturising or antibacterial soaps
or scented oils to clean the device, humidifier or air tubing. These solutions may cause damage and
reduce the life of these products.
Incorrect system setup may result in incorrect mask pressure reading. Ensure the system is
correctly set up.
Be careful not to place the device where it can be bumped or where someone is likely to trip over
the power cord.
Make sure the area around the device is dry and clean and clear of bedding, clothes or other objects
that could block the air inlet or cover the power supply unit.
Ensure that the device is protected against water if used outdoors. Enclose the device in the
S9 travel bag for transport.
9
368876.book Page 1 Thursday, October 11, 2012 2:20 PM
Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum
Center Boulevard San Diego CA 92123 USA.
ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK.
See www.resmed.com for other ResMed locations worldwide.
For patent information, see www.resmed.com/ip.
S9 Escape Auto, SlimLine and ClimateLine are trademarks of ResMed Ltd. S9, Escape, SlimLine and ClimateLine are registered in U.S. Patient and
Trademark Office.
© 2012 ResMed Ltd. 368876/1 2012-10
Global leaders in sleep and respiratory medicine
www.resmed.com
Open as PDF
Similar pages