please read all directions before starting installation

Parts List
2006-2014 Yamaha Raptor
Installation Instructions
1
1
1
2
2
1
Power Commander FC
USB Cable
Installation Guide
Dynojet Decals
Velcro
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE PCFC
CONTROL CENTER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
IFC22002.01
www.powercommander.com
2006-2014 Yamaha Raptor - 1
SELECTING THE MAP POSITION
The Dynojet Power Commander Fuel Controller (PCFC) comes loaded with up to ten
maps. Using a #1 Phillips screwdriver, turn the map select dial to toggle between the
loaded maps. Refer to the map position table for the maps included in your PCFC.
USING THE RPM RANGE DIALS
The Low, Mid, and High RPM Dials refer to the RPM range, in thirds, of your vehicle.
Each dial allows +/- 10% fuel adjustment on top of what fuel changes are done in the
map. With the dial facing straight up, there is no additional fuel change.
STATUS Light
For example, if your vehicle revs to 6000 RPM:
• The low RPM dial will adjust 0-2000 RPM
• The mid RPM dial will adjust 2001-4000 RPM
• The high RPM dial will adjust 4001-6000 RPM
MAP Select
LOW RPM Dial
MID RPM Dial
HIGH RPM Dial
USB Port
USING PCFC CONTROL CENTER
Take your tuning to the next level with the PCFC Control Center software.
1
Using your web browser, navigate to www.powercommander.com.
2
Click Enter Race Ready.
3
Click Downloads.
Click Access Downloads for Power Commander FC.
Position
Note
4
5
Click the PCFC software Download button.
Position 1
2006-2014 Yamaha Raptor 700
Stock exhaust
Stock air filter
Stock airbox
6
Open the zip folder.
7
Double-click the install file and follow the on-screen instructions to install the PCFC
Control Center software. The PCFC Control Center software and maps will be
stored in C:\Program Files\PCFC Control Center.
8
Return to the Downloads or Home page where you can enter the make, model, and
year of your bike to check for and download additional maps.
LOADING ADDITIONAL MAPS
1
Connect the USB cable from the computer to the PCFC. Verify the cable is fully
seated in the PCFC.
2
Run the Control Center software by double-clicking the program icon installed on
your desktop or on your start menu.
3
Click Open Map File and select a map file.
4
Click Send Map. You can send the map to any of the ten map positions.
ALTERING MAPS USING SOFTWARE
The values in the map represent a percentage of fuel change over stock. A value of 10 in
the map indicates at that throttle position and RPM range the vehicle will be 10% richer
than stock. If the value is -10, then it would be 10% leaner than stock. You have the
ability to fine tune your fuel curve by altering these values. The Control Center software
allows a value of +250 to -100 in each cell.
IFC22002.01
www.powercommander.com
2006-2014 Yamaha Raptor - 2
FIG.A
1
Remove the seat.
2
Remove the fuel tank cover and the front shroud over the radiator.
3
Remove the four fuel tank mounting bolts and two push pins. Figure A shows
the two rear mounting bolts and two push pins.
Note: The fuel tank needs to be raised up to access the throttle body. You do
not need to disconnect the wiring harness or the fuel line from the fuel tank.
FIG.B
4
Route the PCFC wiring harness from the rear of the quad to the throttle body
along the left hand side of the frame.
Route the harness behind the air box mounting tab as shown in Figure B.
FIG.C
IFC22002.01
www.powercommander.com
5
Route the PCFC wiring harness between the battery and the battery bracket
as shown in Figure C.
6
Continue routing the PCFC wiring harness underneath the frame and towards
the throttle body.
7
Attach the ground wire from the PCFC to the negative side of the battery as
shown in Figure C.
2006-2014 Yamaha Raptor - 3
FIG.D
8
Unplug the stock wiring harness from the fuel injector as shown in Figure D.
9
Attach the PCFC connectors to the fuel injector and stock wiring harness as
shown in Figure E.
10
Unplug the throttle position sensor (TPS) connector from the right hand side of
the throttle body as shown in Figure F.
FIG.E
FIG.F
The TPS connector is covered with a black rubber boot.
IFC22002.01
www.powercommander.com
2006-2014 Yamaha Raptor - 4
FIG.G
11
Attach the PCFC connectors to the stock TPS connector and wiring harness
as shown in Figure G.
12
Using the supplied velcro, secure the PCFC in the tail section.
FIG.H
Make sure to clean both surfaces with the alcohol swab before attaching.
13
Mount the fuel tank back into place.
Verify the wiring harness will not get pinched or damaged.
14
IFC22002.01
www.powercommander.com
Reinstall the seat.
2006-2014 Yamaha Raptor - 5
Open as PDF
Similar pages