PAYMENT:
Standard terms are 50% of the sales order is due upon receipt of the goods. Net 30 days on the remaining balance. A second invoice will be sent out detailing this.
A service charge of 1.5 % per month may be assessed on invoices over 30 days.
SHIPPING:
Freight will be pre-paid by MTM Hydro for all purchase orders of two machines or more. In the case of shipping one machine, MTM Hydro will pre-pay and add to the
total of the invoice.
PRICING:
MTM HYDRO, Inc. reserves the right to change discounts and/or prices without notice. Trade discounts are based upon unit and dollar volume and are inclusive of
warranty allowance. A surcharge may be added to individual orders in response to foreign currency exchange rate fluctuations.
- Price list effective April 1st, 2015
- Subject to change without notice
- All prices F.O.B. Eden Prairie, Minnesota
- The price in effect at time of shipment will apply.
- Pricing discrepancies must be filed within 30 days of invoice
RETURNS:
- Return for credit must be requested within 30 days of shipment & pre-approved by MTM Hydro Inc.
- All returns must be sent freight paid.
- A return authorization number and invoice copy must accompany all returns.
- Please note that a 20% restocking charge will be assessed.
SHIPPING DISCREPANCIES:
Discrepancies must be submitted within 48 hours of receipt of goods.
Possession of this Catalog or any other MTM Hydro, Inc. material should not be construed as an offer to sell.
STATEMENT OF WARRANTY
LIMITED WARRANTY ON MTM HEAT PRODUCTS
MTM Hydro, Inc. warrants that its products will be free from defects in material and workmanship under normal use for the period of one (1) year. Proof of Purchase
must be provided at the time warranty service is requested. Therefore, you should keep your sales slip or invoice from the original purchase.
Exclusions:
This warranty does not cover freight damage, freezing damage, normal wear and tear from ordinary use, or damage caused by misapplication, fault, negligence,
alterations, improper installation or improper maintenance and service by you or any third party that affects the performance or reliability of the product. Failure to
perform normal and routine maintenance on the heater, damage related to insects, birds, or animals of any kind and damage due to weather conditions will not be not
covered. This warranty does not include wear items, such as, filters, vanes, nozzles and rotors.
In addition, the Limited Warranty does not cover damage to the finish, such as, scratches, dents, discoloration, rust or other weather damage after purchase.
“Normal use” does not include use in excess of recommended maximum speeds, flows, pressures, vacuums and temperatures, or use requiring handling of fluids not
compatible with components and materials noted in MTM Hydro products catalog, technical literature, and instructions.
All Transportation costs for the return of the damaged equipment or components will be the responsibility of the purchaser. If defective MTM Hydro, Inc. will repair or
replace the defective part or equipment and return the item freight pre-paid. If the item is not defective or operating normally, the item will be returned freight collect.
This limited warranty is the exclusive warranty MTM Hydro Inc. makes no other warranty, express or implied, included but not limited to any warranty of
merchantability or fitness for a particular purpose.
MTM Hydro’s obligations under this warranty is, at MTM Hydro’s option during the limited warranty period, to either repair the defective part or equipment or replace
with a new part or equipment upon return of the entire product to the MTM Hydro, Inc. This is the exclusive remedy for any breach of warranty. In no event shall MTM
Hydro Inc. be liable for any special, indirect, incidental, punitive or consequential damages of any kind, whether for breach of any warranty, for negligence on the basis
of strict liability, or otherwise.
Some states do not allow the exclusion or limitation on how long a warranty lasts, so the above exclusion and limitations may not apply to you. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state
For Service or Warranty, contact Customer Service
MTM Hydro, Inc., 7430 Washington Ave. So., Eden Prairie, MN 55344
866.686.4020 / 952.746.4825 / Fax 866.686.4021
Monday - Friday 8:00 a.m. - 5:00 p.m. CST
Notes
FLAME 115 HEATER
Jet Fuel
Kerosene
Diesel #1
Diesel #2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Approved for construction
Approved for agriculture
CSA approved
115,000 BTU’s
Low noise level
Built-in oil burner with Suntec gear pump
Electronic flame control unit with metal casing
Only 92 lbs.
Screw-on fuel cap
AISI 309 L stainless steel cone
Shockproof polythene fuel tank
Automatic post-ventilation cycle to cool down the combustion chamber
Fuel tank drain plug
Possibility of directing the cone up and down with locking mechanism
Fuel lines in hydrocarbon-resistant rubber wire-mesh protected
Extendable sliding floor shield
Poly fuel tank for durability
Made in Italy
Remote thermostat plug
Patented cone design
8” reinforced plastic wheels
FLAME 115
Part Number
Max Power
48.7019
BTU\H
115,160
Fuel Consumption
US GAL\H
0.85
Power Supply
V, PH, HZ
120,1,60
Fan Motor Power
HP (RPM)
1/4 (3,300)
Current Rating
AMPS
2.15
Tank Capacity
US GAL
11.35
HOUR
13.4
Run Time
Pallet
QTY
1
Container 20’
QTY
84
Container 40’ and 40’ HC
QTY
180
FIRE 155 HEATER
Jet Fuel
Kerosene
Diesel #1
Diesel #2
Fire155
Infrared diesel heater (direct-fired) with embedded burner with dedicated fan for combustion air. The Fire155 models are characterized by the
absence of moving air, the flame generated by the burner heats the front plate that reaches high temperature. This helps to burn and stop
all combustion residues, guaranteeing a clean combustion and 100% efficiency. They are used for heating very large spaces (warehouses,
industrial sheds, yards, open spaces, ect.) or where suspended dust particles must be avoided.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Approved for construction
Direct heat flow by radiation with no air movement
Low noise level
Built-in oil burner with Danfoss gear pump
Electronic flame control unit with metal casing
No supervision required: can be controlled by thermostat, humidistat or timer
1ft power cord
AISI 430 stainless steel combustion chamber
Metallic forced air insulation pocket between the combustion chamber and the external
protection cone
Automatic post-ventilation cycle to cool down the combustion chamber
Fuel lines in hydrocarbon-resistant rubber wire-mesh protected
Shockproof polythene fuel tank
Screw-on fuel cap
Fuel tank drain plug
Possibility of directing the cone up and down with locking mechanism
Single point lift bail
Oil filter included (optional pre-heated oil filter)
Combustion air pressure switch (safety device turns off unit and requires manual reset)
12” reinforced plastic wheels
Floor protection sliding shield
Single Fuel Line Kit: This accessory allows the unit to recirculate hot oil from the return
line back into the filter. The hot oil in the filter eases restarts and increases the
performance of the unit in extreme cold temperature
The innovation of the FIRE 155 infrared heater lies in the elimination of the
refractory material cone that surrounds the conical combustion chamber that’s
typical of other competitor’s units. Our heater features a metalic forced air
insulation pocket between the combustion chamber and the external protection
cone. The cooling air is blown through the pocket by the burner fan. This innovative
technology over comes the well known problem of the fragility and brittleness of
the ceramic cone.
Moreover, there is a relevant improvement in the cooling of the cone.
FIRE 155
Part Number
48.7001
Max Power 2nd Stage
BTU\H
154,237
Max Power 1st Stage
BTU\H
--
Fuel Consumption 2nd Stage - 1st Stage
US GAL\H
1.11
Power Supply
V, PH, HZ
120, 1, 60
Fan Motor Power
HP (RPM)
1/4 (3,300)
Current Rating
AMPS
4.1
Tank Capacity
US GAL
17.2
HOUR
16
Run Time 2nd Stage - 1st Stage
Pallet
QTY
1
Container 20’
QTY
26
Container 40’ and 40’ HC
QTY
56
BLAZE HEATER
Jet Fuel
Kerosene
Diesel #1
Diesel #2
Blaze
Diesel indirect-fired portable heaters with embedded burner with combustion air obtained from the main ventilation fan. The Blaze heaters feature a heat
exchanger that contains the flame and expels fumes throughout a chimney connected to the outside. Being indired-fired, they can be operated indoor
and can also be ducted. On the other hand, they have higher upfront costs and about 90% efficiency due to the heat lost through the chimney.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Approved for construction
No supervision required can be controlled by thermostat, humidistat or timer
1ft power cord
AISI 430 stainless steel combustion chamber with four-pass heat exchanger
technology (BLAZE200-BLAZE300)
Automatic post ventilation cycle to cool down the combustion chamber
Electronic flame control unit
Overheating thermostat (safety device turns off unit and requires a manual reset)
Fuel lines in hydrocarbon-resistent rubber wire-mesh protected
Screw on fuel tank cap
Fuel tank drain plug
Electric control panel
Oil filter; pre-heated oil filter (BLAZE200-BLAZE300)
Combustion air pressure switch (safety device turns off unit and requires a
manual reset)
10” pneumatic wheels
Single Fuel Line Kit: This accessory allows the unit to recirculate hot oil from
the return line back into the filter. The hot oil in the filter eases restarts and
increases the performance of the unit in extreme cold temperature
FOUR PASS HEAT EXCHANGER TECHNOLOGY
Combustion chambers are manufactured using AISI 430 stainless steel with
aluminized steel heat exchanger to increase performance. The new fourpass
heat exchanger technology allows exhaust gases to increase heat
exchange with the cooling air and obtain maximum thermal efficiency. Our
heaters are the most efficient in the industry. Available in BLAZE200, BLAZE300 and
all PHOEN heaters.
BLAZE100
Part Number
BLAZE200
BLAZE300
48.7002
48.7003
48.7004
Heat Input
BTU/H
112,141
204,873
293,982
Heat Output
BTU/H
94,759
183,362
258,704
Fuel Consumption
US GAL/H
0.81
1.48
2.17
CFM
1,020
1,530
2,530
°F
95
136
126
Power Supply
V, PH, HZ
120,1, 60
120, 1, 60
120, 1, 60
Fan Motor Power
HP (RPM)
1/4 (3,300)
5/8 (3,300)
1 (1,700)
AMPS
4.05
7.65
11.80
Max Length Flex. Duct (1-Way)
FT
25
50
75
Max Length Flex. Duct (2-Way)
FT
--
25
35
Heated Airflow
Temperature Rise (@64°F)
Current Rating
Flue Size
IN
6
6
6
US GAL
11
17.2
27.7
HOUR
14
14
13
Pallet
QTY
6
1
1
Container 20’
QTY
54
38
24
Container 40’
QTY
132
82
52
Container 40’ HC
QTY
132
82
52
Tank Capacity
Run Time
BLAST HEATER
Jet Fuel
Kerosene
Diesel #1
Diesel #2
Blast
Diesel direct-fired portable heaters with embedded burner with combustion air obtained from the main air fan. The Blast heaters generate hot air and
the combustion residues produced by the burner are expelled with the hot air and contribute to its heating. They transform all of the nominal input power
(from the fuel) into heat, 100% efficiency. They are the most economical models available in terms for upfront cost and consumption. On the other hand,
they can be used only in well ventilated rooms and where indirect-fired heaters are not required by law.
•
•
•
•
•
•
•
•
•
•
•
•
•
Approved for construction
Built-in oil burner with Danfoss gear pump
Electronic flame control unit
Combustion air pressure switch (safety device turns off unit and
requires a manual reset)
No supervision required; can be controlled by thermostat,
humidistat or timer
1ft power cord
AISI 430 stainless steel combustion chamber
Automatic post ventilation cycle to cool down the combustion chamber
Fuel lines in hydrocarbon-resistant rubber wire-mesh protected
Screw on fuel tank cap
Fuel tank drain plug
10” pneumatic wheels
Single Fuel Line Kit: This accessory allows the unit to recirculate
hot oil from the return line back into the filter. The hot oil in the
filter eases restarts and increases the performance of the unit
in extreme cold temperature
2
Part Number
Max Power
Fuel Consumption
BLAST250
BLAST360
BLAST400
48.7005
48.7006
48.7022
48.7007
BTU/H
238,947
361,439
361,439
599,524
US GAL/H
1.72
2.6
2.6
4.32
Heated Airflow
CFM
1,460
1,795
1,795
2,800
Power Supply
V, PH, HZ
120,1, 60
120, 1, 60
120,1,60
120,1,60
Fan Motor Power
HP (RPM)
5/8 (3,300)
5/8 (3,300)
1 (1,700)
1 (1,700)
Current Rating
AMPS
5.1
6
7.5
11.1
Tank Capacity
US GAL
17.2
27.7
27.7
35.6
HOUR
10
11
10
8
Run Time
Pallet
QTY
1
1
1
1
Container 20’
QTY
38
28
24
24
Container 40’
QTY
82
58
52
52
Container 40’ HC
QTY
82
58
52
52
4
3
1
5
6
7
BLAST600
DUST AND WATER PROOF ELECTRIC PANEL
1 Reset button with lock out (red), working (green) and stand-by
(orange) indicator light
2 Three-way control switch
• position 0 for stop
• position 1 for “continuous” burning
• position 2 for ON with remote thermostat, humidostat, timer
3 Socket for remote thermostat, humidostat, timer
4 Voltage warning light (connected to the mains)
5 Power cord
6 Plastic cover
7 Power cord bracket
BLAST/N HEATER
Jet Fuel
Kerosene
Diesel #1
Diesel #2
Blast/N
Gas (propane or natural gas) direct-fired portable heaters with embedded burner with a combustion air obtained from the main ventilation fan. The
Blast/N heaters generate hot air and the combustion residues produced by the burner are expelled with the hot air and contribute to its heating. They
transform all of nominal input power (from the fuel) into heat, 100% efficiency. They are the most economical models available in terms of upfront
cost and consumption. On the other hand, they can be used only in well-ventilated rooms and where indrect-fired heaters are not required by law.
BLAST/N250 BLAST/N400
Part Number
Max Power NG/LP
•
•
•
•
•
•
•
•
•
•
•
•
•
Approved for construction
Built-in oil burner with Danfoss gear pump
Electronic flame control unit
Combustion air pressure switch (safety device turns off unit and requires a manual reset)
No supervision required; can be controlled by thermostat, humidistat or timer
1ft power cord
AISI 430 stainless steel combustion chamber
Automatic post ventilation cycle to cool down the combustion chamber
Fuel lines in hydrocarbon-resistant rubber wire-mesh protected
Bayonet-type fuel tank cap
Fuel tank drain plug
10” pneumatic wheels
Single Fuel Line Kit: This accessory allows the unit to recirculate hot oil from
the return line back into the filter. The hot oil in the filter eases restarts and
increases the performance of the unit in extreme cold temperature
Feul Consumption NG
48.7023
48.7008
BTU/H
254,683
402,767
CFH
242
381
Fuel Consumption LP
CFH
89
145
Heated Airflow
CFM
2,766
4,120
F
86
103
Temperature Rise (@64 F)
Max Length Flex. Duct
Ft
50
50
Max Air Static Press. Avail.
PA
150
140
Power Supply
V, PH, HZ
120,1,60
120,1,60
Fan Motor Power
HP (RPM)
5/8 (3,300)
1 (1,700)
AMPS
5
8.5
Pallet
QTY
1
1
Container 20’
QTY
60
26
Container 40’
QTY
129
54
Container 40’ HC
QTY
129
81
Current Rating
FIRESTORM HEATER
Jet Fuel
Kerosene
Diesel #1
Diesel #2
Firestorm
Heavy duty diesel indirect-fired portable heaters with embedded burner with dedicated fan for combustion air. The Firestorm heaters feature a heat
exchanger that contains the flame and expells fumes throughout a chimney connected to the outside. Being indriect-fired, they can be operated
indoors and can also be ducted. On the other hand, they have higher upfront costs and about 90% efficiency due to the heat lost through the chimney.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Approved for construction
Separated burner blower
Two-stage dedicated burner (low and high fire selector)
1ft power cord
Combustion chamber pre-heating cycle
Electronic flame control unit
Fuel lines in hydrocarbon-resistant rubber wire-mesh protected
Screw on fuel tank cap
Fuel tank drain plug
Ventilation only mode (fan can be operated when burner is off)
Pre-heated oil filter (not included with FIRESTORM/S)
Anti-shock frame with foldable handle (FIRESTORM400 HC)
Single point lift bail and forklift pockets
12” pneumatic wheels (16” for HC version)
Optional return air adapter for inside warm air recirculation
Heater is shipped fully assembled
No supervision required: can be controlled by thermostat, humidistat or timer
Combustion air pressure switch (safety device: turns off unit and require manual reset)
Convection fan is controlled by thermostat that measure combustion chamber temperature
AISI 430 stainless steel combustion chamber with four-pass heat exchanger technology
Single fuel line kit: allows to recirculate hot oil from the return line back into the
pre-heated filter to maintain oil warmer in the filter and favorite cold starts and
better burning perfomance in extreme cold temperature
DEDICATED TWO-STAGE OIL BURNER
The Phoen line of heaters features a built-in burner specifically designed and optimized for
cylindrical combustion chambers typical of our cannon-type heaters. The burner features a
two-stage oil pump and a separated combustion air blower. Combined to the four-pass heat
exchanger, enables to run the unit at 85% efficiency, one of the highest in the industry
5
4
2
7
6
1
3
Legend
1 Combustion head
2 Blower motor
3 Combustion air blower
4 Double stage diesel pump (Suntec)
5 Combustion air regulation valve
6 Electrodes – Nozzle
7 Flexible hose connecting blower to combustion head
Part Number
Firestorm 400
Firestorm 400HC
48.7016
48.7009
411,905
411,905
Heat Input 2nd Stage
BTU/H
Heat Input 1st Stage
BTU/H
272,189
272,189
Heat Output 2nd Stage
BTU/H
354,239
354,239
Heat Output 1st Stage
BTU/H
231,360
231,360
Fuel Consumption 2nd Stage
US Gal/H
2.97
2.97
Fuel Consumption 1st Stage
US Gal/H
1.96
1.96
CFM
3,250
3,250
Airflow
Temp. Rise (@64 F) 2nd Stage
F
132
132
Temp. Rise (@64 F) 1st Stage
F
108
108
V,PH,Hz
120,1,60
120,1,60
Power Supply
Fan Motor Power
HP (RPM)
1 (1,700)
1 (1,700)
Burner Motor Power
HP (RPM)
1/4 (3,300)
1/4 (3,300)
AMPS
13
13
Max Length Duct 1-Way/2-Way
Ft
100/60
100/60
Max Length Air Inlet Duct
Ft
30
30
Max Length Fresh Air Intake
Ft
15
15
Current Rating
Flue Size
In
6
6
US Gal
35.6
57
Run Time 2nd Stage - 1st Stage
Hr
18 - 12
29 - 19
Pallet
Qty
1
1
Container 20’/40’/40’HC
Qty
8/18/36
7/16/31
Tank Capacity
INFERNO HEATER
Jet Fuel
Kerosene
Diesel #1
Diesel #2
Inferno
Large indirect-fired portable heaters with external burner (gas or diesel). The Inferno heaters are suitable for high volume spaces and can run on diesel or
gas (LPG or natural gas), depending on the burner and can be equipped with an axial or a centrifugal fan. Centrifugal fans are very quiet, ensures greater
pressure and is particularly recommended for installations with ducts.
Part Number
•
•
•
•
•
Approved for construction
Available with oil or gas (NG or LP) burner
Riello burner
Electronic flame control unit
Thermostats: FAN, TEMP LIMIT with automatic reset,
overheating with manual reset
• Convection fan is controlled by thermostat that measure
combustion chamber temperature
• No supervision required: can be controlled by thermostat,
humidistat or timer
• Casing with double steel protection for better thermal and
acoustic insulation
• AISI 430 stainless steel combustion chamber with
aerodynamic shape
• Ventilation only mode (fan can be operated when burner is off)
• Available with both axial or centrifugal fan (axial fan for a
more compact unit and centrifugal fan “C” when higher
static pressure is needed)
• Lifting brackets
• 16” pneumatic wheels for easy mobility
• Hour meter
• Forklift pockets
• Pre-heated oil filter (oil version only)
Inferno 700
Inferno 700C
Inferno 900
Inferno 900C
48.7013
48.7024
48.7018
48.7025
Heat Input
BTU/H
700,000
700,000
900,000
900,000
Heat Output
BTU/H
595,000
595,000
765,000
765,000
CFM
7,420
7,420
8,830
8,830
US GAL/H
5.04
5.04
6.48
6.48
CFH
685
685
881
881
In.
Min. 7in W.C. Max. 14in W.C.
Min. 7in W.C. Max. 14in W.C.
Min. 7in W.C. Max. 14in W.C.
Min. 7in W.C. Max. 14in W.C.
Heated Airflow
Fuel Consumption
Fuel Consumption NG
Min. Supply Pressure NG
Fuel Consumption LP
Min. Supply Pressure LP
Max Air Temperature
CFH
275
275
353
353
In.
Min. 8in W.C. Max 14in W.C.
Min. 8in W.C. Max 14in W.C.
Min. 8in W.C. Max 14in W.C.
Min. 8in W.C. Max 14in W.C.
F
250
250
250
250
Power Supply
V, PH, HZ
220,1,60
220,1,60
220,1,60
220,1,60
Fan Motor Power
HP (RPM)
2 (1,700)
3 (1,700)
3 (1,700)
4 (1,700)
Burner Motor Power
HP (RPM)
1/4 (3,300)
1/4 (3,300)
1/4 (3,300)
1/4 (3,300)
AMPS
7.8
13.5
10.3
15
Ft.
200’
300’
200’
300’
150’
Current Rating
Max Length Duct 1-Way
Max Length Duct 2-Way
Ft.
100’
150’
100’
Max Length Duct 3-Way
Ft.
50’
75’
50’
75’
Max Length Duct 4-Way
Ft.
30’
40’
30’
40’
8
In.
8
8
8
Pallet
Flue Pipe
QTY
1
1
1
1
Container 20’
QTY
8
8
7
7
Container 40’
QTY
16
16
15
15
Container 40’ HC
QTY
32
28
15
15
ACCESSORIES
FIRE 155 ACCESSORIES
Part Number
48.7102
Fuel Level Gauge
Part Number
48.7101
Heavy Duty Thermostat
Part Number
Part Number
48.7103
48.7104
Single Fuel Line Kit
Pre-heated Oil Filter (200W)
BLAST ACCESSORIES
Part Number
48.7121
Fuel Level Gauge
Part Number
48.7122
Fuel Tank Filler Filter
Part Number
48.7123
Lifting Brackets (4 Pieces)
A
A
+
C
B
Part Number
48.7127
Heavy Duty Thermostat
Part Number
Part Number
48.7124
External Fuel Tank Connection Kit
Part Number
48.7125
External Fuel Tank Connection Kit
With Deaerator
Part Number
48.7126
Pre-heated Oil Filter (200W)
(Standard For Blast200 &
Blast300
48.7128
Single Fuel Line Kit
FIRESTORM ACCESSORIES
Fuel level gauge
Part Number
48.7121
Fuel tank filler filter
Part Number
48.7122
Lifting brackets (4 pieces)
Part Number
48.7123
A External fuel tank connection kit
Part Number
48.7124
A External fuel tank connection kit
+ with deaerator
C Part Number
48.7125
B Pre-heated oil filter (200W)
Part Number
48.7126
Heavy duty thermostat
(20÷140°F)with 30’ cable
Part Number
48.7127
Single fuel line kit
Part Number
48.7128
ACCESSORIES
BLAZE ACCESSORIES
Part Number
48.7105
Fuel Level Gauge
Part Number
48.7106
Fuel Tank Filler Filter
Part Number
Part Number
48.7107
Part Number
Model
Part Number
Model
Part Number
48.7109
Blaze100 - 12”
48.7112
Blaze200 - 12” + 12”
Heavy Duty Thermostat
48.7114
48.7110
Blaze200 - 14”
48.7110
Blaze300 - 12” + 12”
48.7111
Blaze300 - 16”
Two-way Duct Adapter
A
A
+
C
One-way Duct Adapter
48.7104
Single Fuel Line Kit
Lifting Brackets (4 Pieces)
B
Part Number
48.7124
External Fuel Tank Connection Kit
Part Number
48.7125
External Fuel Tank Connection Kit
With Deaerator
Part Number
48.7126
Pre-heated Oil Filter (200W)
(Standard For Blaze200 &
Blaze300
INFERNO ACCESSORIES
Part Number
Model
Part Number
Model
Part Number
Model
Part Number
48.7181
Inferno700 - 24”
48.7182
Inferno700 - 20”+20”
48.7178
Inferno700 (42 Gal)
Inferno Fuel Tank Kit
48.7203
Inferno900 - 24”
Two-way Duct Adapter
48.7199
Inferno900 (55 Gal)
One-way Duct Adapter
Part Number
48.7200
Inferno Fuel Tank Kit
Part Number
Air Outlet
TBD
48.7200
Fuel Tank
Part Number
48.7114
Heavy Duty Thermostat
Part Number
TBD
Three-Way Duct Adapter
Part Number
TBD
Four-Way Duct Adapter
5
1
0
2
MTM Hydro Inc.
Phone: 952.746.4825 - 866.686.4020
Fax: 952.746.4829 - 866.686.4021
orders@mtmhydro.com
Open as PDF
Similar pages