mr.steam
®
Technical Specifications
CT Day Spa Packages
CT DAY SPA SYSTEM For Models CT6 to CT15
BOX CONTENT
• iTempoPlus® Control
• Matching AromaSteam Steamhead with Acrylic Shield (not shown)
• AutoFlush® System
• Express Steam® factory installed (not shown)
• Drip Pan
• CT-SteamStop™
• MSTS In-Room Temperature Sensor (not shown)
CT-PACKAGE ISTEAM For Models CT6 to CT15
BOX CONTENT
• Steam Control
• Matching iSteam Steamhead
• AutoFlush® System
• Express Steam® factory installed (not shown)
• Drip Pan
• CT-SteamStop™
• MSTS In-Room Temperature Sensor (not shown)
FOR ILLUSTRATIVE PURPOSES ONLY. IMPORTANT NOTE: FOR SAFE AND TROUBLE FREE INSTALLATION
visit mrsteam.com or scan the QR code before installation to download the Installation, Operation and
Maintenance Manual or refer to the manual provided with the unit.
MODEL
SHAPE
FINISH
CT DAY SPA RD Round PC - Polished Chrome
SYSTEM
SQ Square BN - Brushed Nickel
PN - Polished Nickel
ORB - Oil Rubbed Bronze
BB - Brushed Bronze
PB - Polished Brass
RAW - Custom Plating
N/A
CT-PACKAGE
WH - White
iSteam
BK - Black
mr.steam®
PROJECT INFORMATION
Location:
Architect:
Engineer:
Contractor:
Submitted By:
Date:
Notes:
Sussman-Automatic Corp® hello@mrsteam.com www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM fax: 718 472 3256
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM fax: 310 216 2944
TS0052 12.14
mr.steam
®
T E C H N I C A L S P E C I F I C AT I O N S
BOX CONTENTS:
iTempoPlus™ CONTROLS
iTempoPlus™ controls flush mount in the steam/shower enclosure through a
2 5⁄8” wide x 3 7⁄8” high hole. iTempo controls can also be surface mounted.
Dimensional
Information for the
round and square
controls:
iTempoPlus™ Controls Feature:
• Solid brass decorative cover
with choice of square or round
styles in designer finishes
• Digital display
• Programmable temperature
• AromaSteam steamhead in
matching finish and shape
• Compatibility with iGenie®
• iTempoPlus™ • Tube of Silicone Sealant
• Steamhead
• Owner’s Manual
• Control Cable (30 ft.)
• Soft touch keypad
• Low voltage operation
• Programmable steam bath
duration
• Clock
• ON/OFF control for AromaSteam
and ChromaSteam®
• Two programmable presets
41/2”
21/2”
1”
3/8”
5”
The iTempoPlus controls are designed to be installed inside or outside
the steam room but is primarily installed inside the steam room. If the
control is installed inside the steam room the control must be located:
• 4-5 feet above the floor
• in a location representative of the desired steam bathing
temperatures. Do not locate the control above or near the
steam head or direct steam emissions.
• on a vertical wall
The control cable length is 30 feet. Insure that the control and/or
steam generator are located accordingly.
An optional 60 ft. cable is available if required, PN 103990-60.
If the control is installed outside the steam room a Remote Temperature
Probe Part Number MSTS must be installed inside the steam room.
1/4”
5”
3/ ”
4
12” long
pigtail
FOR ILLUSTRATIVE PURPOSES ONLY.
IMPORTANT NOTE: FOR SAFE AND TROUBLE FREE INSTALLATION
visit mrsteam.com or scan the QR code before installation to download
the Installation, Operation and Maintenance Manual or refer to the
manual provided with the unit.
MODEL
MS iTempoPlus
SHAPE
FINISH
RD Round BB - Brushed Bronze
SQ Square BN - Brushed Nickel
ORB - Oil Rubbed Bronze
PB - Polished Brass
PC - Polished Chrome
PN - Polished Nickel
RAW - Custom Plating
PROJECT INFORMATION
Location:
Architect:
Engineer:
Contractor:
Submitted By:
Date:
Notes:
mr.steam®
Sussman-Automatic Corp® hello@mrsteam.com www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM fax: 718 472 3256
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM fax: 310 216 2944
TS0035 Rev 5.14
33/4”
mr.steam
®
Technical Specifications
iSteam 2.0 Control
®
Box Contents:
• iSteam® 2.0 Control
• Owner’s Manual
• Control Cable (30 ft.)
• Rough-In Box
• Steamhead
• Optional Surface
• Tube of Silicone
Sealant Mount Gasket
Dimensional Information
13⁄8”
5
6 ⁄16”
Control
Pigtail (8”)
ID Tag
10:06 AM
4 3⁄4”
START
ACCESSORIES
Blue Cap
Audio Pigtail
(71⁄4”)
SETTINGS
Wall location for
optional surface mount
Wall location
for flush mount
iSteam controls flush mount in the steam/shower enclosure
through a 5-1/4” wide x 3-9/16” high hole. iSteam controls
can also be surface mounted. They are suitable for use with an
available iGenie® control. Available in black or white.
The iSteam controls are designed to be installed inside
or outside the steam room but is primarily installed inside the steam room. If the control is installed inside
the steam room the control must be located:
• 4-5 feet above the floor
iSteam controls are suitable for use inside or outside the
steam/shower enclosure, featuring:
• Full color LCD touch screen
• Programmable temperature
• Programmable time
• Two user presets
• Passcode to prevent unintentional use of steam bath
• Includes AromaSteam steam
head in white or black
• Compatible with iGenie®
• AromaSteam, ChromaSteam®
• Low voltage operation
and AudioWizard™ controls
Works with the iSteam® Mobile App to allow users to control
steamroom operation from their local WiFi network.
• In a location representative of the desired steam
bathing temperatures near the bather seating area.
Do not locate the control above or near the steam
head or direct steam emissions.
• On a vertical wall
The control cable length is 30 feet. Insure that the control and/ or steam generator are located accordingly.
An optional 60 ft. cable is available if required, PN
104117-60. If the control is installed outside the steam
room a Remote Temperature Probe Part Number
iMSTS must be installed inside the steam room.
FOR ILLUSTRATIVE PURPOSES ONLY. IMPORTANT NOTE: FOR SAFE AND TROUBLE FREE INSTALLATION
visit mrsteam.com or scan the QR code before installation to download the Installation, Operation and
Maintenance Manual or refer to the manual provided with the unit.
MODEL
iSteam 2.0
FINISH
Black
White
PROJECT INFORMATION
Location:
Contractor:
Architect:
Submitted By:
Engineer:
Date:
Notes:
mr.steam®
Sussman-Automatic Corp® hello@mrsteam.com www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM fax: 718 472 3256
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM fax: 310 216 2944
TS0036 REV 5.14
mr.steam
®
Technical Specifications
AutoFlush
®
AutoFlush Shown Fully Assembled
Box Contents
• AutoFlush Valve with Cord
• Installation instructions
Operation
The optional AutoFlush System feature automatically drains the
Mr.Steam® system following each use.
A time delay allows the water to cool
down (about two hours) before it
drains by gravity for a safe and gentle
operation.
Note: If the Express Steam® option
has been installed, the AutoFlush will
drain for ten minutes then refill with
fresh water to begin the pre-heat
cycle.
AutoFlush Valve
Steam Generator
Drain Valve
DO NOT TURN OR REMOVE THE DRAIN VALVE
(shown in the correct open position)
Nipple
Plumb to
Drain Line
Our exclusive AutoFlush® automatically and electronically drains the system,
providing CleanSteam... Every Time® and introduces fresh water.
FOR ILLUSTRATIVE PURPOSES ONLY. IMPORTANT NOTE: FOR SAFE AND TROUBLE FREE INSTALLATION
visit mrsteam.com or scan the QR code before installation to download the Installation, Operation and
Maintenance Manual or refer to the manual provided with the unit.
MODEL
PROJECT INFORMATION
MS 81500E
Location:
Contractor:
Architect:
Submitted By:
Engineer:
Date:
Notes:
mr.steam
®
Sussman-Automatic Corp® hello@mrsteam.com www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM fax: 718 472 3256
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM fax: 310 216 2944
TS0011 REV 5.14
mr.steam
®
Technical Specifications
Drip Pan MS 103867
Mr. Steam strongly recommends the use of
a drain pan in the unlikely event of a
plumbing leak.
Locate the drain pan on a solid level
surface and place the steam generator
inside the drain pan. Insure the steam
generator is level.
All plumbing shall be performed by a
qualified licensed plumber and in accordance with applicable national and local
codes. Check local plumbing code for
receptor, trap and vent requirements.
Drain pans drain by gravity.
The drain pan is equipped with an integral
3⁄4" NPT fitting.
9”
25”
1.5”
FOR ILLUSTRATIVE PURPOSES ONLY. IMPORTANT NOTE: FOR SAFE AND TROUBLE FREE INSTALLATION
visit mrsteam.com or scan the QR code before installation to download the Installation, Operation and
Maintenance Manual or refer to the manual provided with the unit.
MODEL
PROJECT INFORMATION
MS 103867
Location:
Contractor:
Architect:
Submitted By:
Engineer:
Date:
Notes:
mr.steam
®
Sussman-Automatic Corp® hello@mrsteam.com www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM fax: 718 472 3256
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM fax: 310 216 2944
TS0012 REV 5.14
mr.steam
®
Technical Specifications
CT-SteamStop
™
BOX CONTENT
• CT-SteamStop™ Control Button
• Owner’s Manual
• 60’ CT-SteamStop Cable
FUNCTION
• Used to turn the steam room on and off from
within the steam room without having to touch
the main controller
• Works with both iTempoPlus® and iSteam® controls
• Adhesive sticker for mounting located on the back
of the button (non-supplied silicon is required to
properly seal the wall opening).
FOR ILLUSTRATIVE PURPOSES ONLY. IMPORTANT NOTE: FOR SAFE AND TROUBLE FREE INSTALLATION
visit mrsteam.com or scan the QR code before installation to download the Installation, Operation and
Maintenance Manual or refer to the manual provided with the unit.
MODEL
PROJECT INFORMATION
CT-SteamStop™ Location:
Contractor:
Architect:
Submitted By:
Engineer:
Date:
Notes:
mr.steam®
Sussman-Automatic Corp® hello@mrsteam.com www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM fax: 718 472 3256
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM fax: 310 216 2944
TS0065 12.14
mr.steam
®
Technical Specifications
MSTS/iMSTS in Room Temperature Sensor
BOX CONTENT
• MSTS/iMSTS probe with wire attached
FUNCTION
• Used to accurately read the temperature inside the steam
room and send it to the controller.
• MSTS is for use with the iTempo® or iTempoPlus® controls
• iMSTS is for use with the iSteam® Control
1⁄4" Minimum
Silicone Sealant
1⁄ 2" Maximum
Probe
Finish Wall
SECTIONAL VIEW
Cable
INSTALLED REMOTE
TEMPERATURE PROBE
FOR ILLUSTRATIVE PURPOSES ONLY. IMPORTANT NOTE: FOR SAFE AND TROUBLE FREE INSTALLATION
visit mrsteam.com or scan the QR code before installation to download the Installation, Operation and
Maintenance Manual or refer to the manual provided with the unit.
MODEL
PROJECT INFORMATION
iMSTS
MSTS
Location:
Contractor:
Architect:
Submitted By:
Engineer:
Date:
Notes:
mr.steam®
Sussman-Automatic Corp® hello@mrsteam.com www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM fax: 718 472 3256
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM fax: 310 216 2944
TS0055 12.14
Open as PDF
Similar pages