PP6X Printer - ACLAS Polska

KP7MX PRINTER
DRIVER INSTALLATION
INSTRUCTION
Pinnacle Technology Corp.
CONTENTS
1
2
USB/SERIAL PRINTER DRIVER INSTALLATION ...................................................................................... 1
1.1
Printer Driver Installation .................................................................................................................. 1
1.1.1
Serial /Parallel Printer Driver Installation .................................................................................. 3
1.1.2
USB Printer Driver Installation ................................................................................................. 6
1.1.3
Ethernet/WIFI Printer Driver Installation .................................................................................. 8
1.2
How to Know the Connecting Port .................................................................................................. 10
1.3
How to Configure Port..................................................................................................................... 13
WIRELESS 2.4G / WIRELESS 433 PRINTER (KP7XW4/KP7XW2) .......................................................... 19
2.1
Printer Driver Installation ................................................................................................................ 19
2.2
Wireless 433MHz Base Station ....................................................................................................... 23
2.3
Wireless 433 USB Dongle/2.4G ...................................................................................................... 25
2.3.1
USB Dongle Driver Installation............................................................................................... 25
2.3.2
How to Know the Connecting Port .......................................................................................... 28
2.3.3
Dongle Parameter Setting ........................................................................................................ 29
2.4
How to Configure Port..................................................................................................................... 30
1 USB/SERIAL PRINTER DRIVER INSTALLATION
1.1 Printer Driver Installation
Connect the KP7X to PC, run the attached CD-disk and double click the file ‘Aclas
printer.exe’ in the folder ‘Aclas Printer’ to install the printer driver.
Click”Next”
Click “Browse” to choose
the destination location.
Click “Next”
1
Here shows the
install destination
location
Click “Install”
2
1.1.1 Serial /Parallel Printer Driver Installation
Choose “COM/LPT”
Choose the right connect
port from the drop-down
list.
If the printer is serial printer, the
user must click “Setting” to
config the connect ports.
3
Choose “Hardware”
Click “OK”.
Click “Install”
4
Click
“Finish”
to
Serial/parallel printer
installation.
5
finish
driver
1.1.2 USB Printer Driver Installation
Choose “USB”
Choose the USB port from the
drop-down list and click
“Install”
6
Click “finish” to finish USB
printer driver installation.
7
1.1.3 Ethernet/WIFI Printer Driver Installation
Choose “TCP”
Input IP address. The
default port is 9100.
8
Click “Finish” to finish
Ethernet/WIFI
printer
driver installation.
Note:
After installing the printer driver, you can use the printer. If the printer could not work,
you can refer to Chapter 1.2 to see the connecting port and make sure that the connecting
port you choose is correct and is not being used; then refer to Chapter 1.3 to configure
port.
9
1.2 How to Know the Connecting Port
Connect the KP7X to the computer, follow steps below to know which port is connected.
Right click ‘My Computer’ icon on the desktop, and choose ‘Manage’:
Right
click
the
‘My
Computer’ icon and then
choose ‘Manage’.
Click
‘Device
Manager’
Then click ‘Port
(COM&LPT)’
10
Serial printer connect port:
Here you can see the
此处显示串口打印
connecting port of
serial printer.
机的连接端口
Parallel printer connect port:
Here you can see the
connecting port of
parallel printer.
11
USB printer connect port:
Here you can see the
connecting port of
USB printer.
12
1.3 How to Configure Port
Step1: Enter ‘properties’ interface of the printer first to configure port
after knowing the connecting port.
 If your PC is installed with Windows XP system, please follow the below steps to enter
‘properties’ interface.
Click ‘Printers and
Faxes’ in start menu.
Right click the printer icon, and
choose the item ‘Properties’.
13
 If your PC is installed with Vista system, please follow the below steps to enter ‘properties’
interface.
Click ‘Printers’ after
choosing ‘Settings’ in
start menu.
Click this item.
Choose the item
‘Properties’.
14
Note: If you are not allowed to access to run as the administrator, please choose the item
‘properties’ directly after entering the Printer interface, as the window below:
Right click the printer
icon, and then choose the
item ‘Properties’.
 If your PC is installed with WIN7 system, please follow the below steps to enter ‘properties’
interface.
Click “Devices
and Printers” in
start menu.
15
Right click “Aclas Printer”,
choose “Printer properties ”.
16
Step 2: Choose connecting port
Choose the connecting port that you have known from Chapter 1.2. For example, the connecting
port of the USB printer known from Chapter 1.2 is COM3, so you should choose COM3 in the
following interface. Take the port configuration of USB printer in Windows XP system as an
example:
Choose
item.
this
Select
the
connecting port.
Click
it.
Step 3: configure port
Note: Parallel printers and USB could skip this step, and go to step 4 directly.
Click it
17
Choose “Hardware”
Click “OK”.
Step 4: finish port configuration
Choose the item
‘General’
Click it to print test page, and
then click ‘OK’.
18
2 WIRELESS 2.4G / WIRELESS 433 PRINTER (KP7XW4/KP7XW2)
The communication distance: KP7 wireless 433 printer is up to 100m without obstacle
KP7 wireless 2.4G printer is up to 10m without obstacle
KP7X printers of this model are able to communicate with PC by two ways, via 433MHz Base Station or 2.4G
Dongle. If you use 433MHz Base Station, please refer to Chapter 3.2; if use 2.4G Dongle, please refer to
Chapter3.3.
2.1
Printer Driver Installation
Note: The working baudrate of wireless 433 printer is ‘9600’, its printing speed is relatively lower, it had
better not use driver printing, we suggest that you should adopt command print.
The installation of printer driver is as follow.
Connect the KP7X to PC, run the attached CD-disk and double click the file ‘Aclas printer.exe’ in the folder
‘Aclas Printer’ to install the printer driver.
Click ‘Next’
19
Click ‘Next’
Click ‘Browse’ to select
the destination location.
Click ‘Next’
20
Here shows the destination
location.
Click ‘Install’
Click “Next”
21
Click ‘Install’
Click ‘Finish’ to
finish printer driver
installation.
22
2.2
Wireless 433MHz Base Station
 Wireless Printer Setting:
If Base Station needs to communicate with printer, the following operation should be carried out.
1. Power on BS via power supply adaptor, the power indicator light lightened.
2. BS communicates with PC via Ethernet.
3. Double click ‘Internet Explorer’ on your PC desktop, input Base Station IP ‘192.168.1.14’, and then press
[Enter] on your keyboard, system displays as follows:
1. Input password (the default
password is ‘admin’.)
2. Click ‘submit’.
4. Enter ‘station menu’ interface, choose ‘Printer IP Address Settings’ item:
23
Add, Remove, or Change printer server listening port in the interface below:
If choose ‘Add IP Address To List’ to add printer, please input the new added printer’s ‘IP address’ and
‘comments’, and click ‘add’.
Input the new added
printer’s IP address.
Click ‘Add’
24
If you choose ‘Remove IP Address From List’, please input the new added printer’s IP address or comments,
and click ‘Remove’; if you need to delete IP address, please click ‘Reset’.
Input IP address.
Click ‘Remove’
2.3
Wireless 433 USB Dongle/2.4G
2.3.1
USB Dongle Driver Installation
You can install the USB dongle driver after you install printer driver.
Double-click file CP210x_VCP_Win2K_XP_S2K3.exe, pop-up this window:
Click ‘Next’
25
Click ‘Browse’ to select the
destination location.
Click ‘Next’.
Click ‘Install’.
26
Click ‘Install’.
Choose this item.
Click ‘Finish’.
Click ‘OK’.
27
2.3.2 How to Know the Connecting Port
After you install USB dongle driver, restart computer, and insert the 433 dongle into the USB port of computer.
Then, you can follow below steps to know which port is connected. Right click ‘My Computer’ icon on the
desktop, and choose ‘Manage’.
Right click the ‘My Computer’
icon and then choose ‘Manage’.
Click ‘Device
Manager’
Then click ‘Port
(COM&LPT)’
28
Here you can see the
connecting port of the
printer.
2.3.3 Dongle Parameter Setting
In the disk, you can find the file ‘DownloadDongle.exe’, double click to open it. Download setting to 433
dongle in order to realize wireless connection between PC and the printer.
Choose the correct COM port
which was known just now.
Choose‘Hard’
Click this button to
download setting.
Local IP: the IP of 433 dongle.
Target Dongle IP: the wireless IP address of KP7HW4.
Stream CTRL: stream control, if the transmitting data is over 255byte, please choose ‘Hard’. If the software is
used to transmit data, please set the stream control as ‘Hard’.
Note: After click the button ‘Download’, if the system display ‘Download OK’, it prompts the parameter
setting is successful, and then please pull out the dongle and insert it again; if the system display ‘Fail’,
please check whether you choose the correct COM port, or whether the COM port is occupied by other
equipment.
29
2.4
How to Configure Port
After knowing the connecting port, it is necessary to configure the port. Enter ‘properties’ interface first to
configure port.
 If your PC is installed with Windows XP system, please follow the below steps to enter ‘properties’
interface.
Click ‘Printers and Faxes’
in start menu.
Right click the printer
icon, and choose the item
‘Properties’.
30

If your PC is installed with Vista system, please follow the below steps to enter ‘properties’ interface.
Click ‘Printers’ after
choosing ‘Settings’ in
start menu.
Click this item.
Choose the item
‘Properties’.
31
Note: If you are not allowed to access to run as the administrator, please choose the item ‘properties’
directly after entering the Printer interface, as the window below:
Right click the printer
icon, and then choose
the item ‘Properties’.
After entering ‘properties’ interface, you can configure port. The port configuration steps of PC with Windows
XP system and PC with Vista system are the same. Take the port configuration steps of PC with Windows XP
system for example:
32
Choose the item ‘Ports’.
Choose the port which was
known in Chapter 3.3.2.
Click it
Click it
33
Choose 9600
Choose ‘Hardware’.
Click it
Choose the item
‘ General’.
Click it to print test page
and then click ‘OK’.
34
Revision:01
Open as PDF
Similar pages