Edge Insight Digital Gauge Installation Instructions

CS/CTS QUICK INSTALL INSTRUCTIONS
Supplied Items
1.
2.
3.
4.
5.
6.
7.
CS or CTS Device
Arkon Windshield Mount
OBDII Cable
Mini USB Cable
CD
Alcohol Wipe
Zip Tie Packet
Suggested Tools
•
Flat head screwdriver
Step 1:
Locate the OBDII Port
4
6
Connect/Route the OBDII Cable
The OBDII port is a 16-pin connector like the illustration below.
Remove the panel on the
side of the dashboard to
provide access to route
the OBDII cable from the
OBDII port up to the top
of the dash.
OBDII PORT
1
2
Step 2:
3
5
7
OBDII LOCATIONS
The OBDII port is located under the dash below
the steering wheel.
The OBDII port is
placed in different
locations under the
dash for different
applications; refer to
the OBDII port location drawing (left) to
help you locate your
OBDII port. If you are
unable to locate your
OBDII port, there may
be a sticker underneath
the steering column that may
explain where your OBDII is
located.
*On some vehicles you may also
need to remove the panel directly
under the steering wheel.
Step 3:
Position the Device
Step 4:
Connect the Mount and OBDII Cable
Before you attach the
suction cup portion of the
mount to the window attach it to the device. Insert
the tabs on the mount into
the slots on the back of the
device and slide up (CTS)
or to the side (CS) until it
stops.
Position the device
and the mount on
the windshield in the
desired location.
Pay attention to
where the suction
cup will mount on the
windshield.
*The mounting tabs are a tight fit by
design to maintain a solid connection.
Once you’ve removed
the necessary panels,
connect the OBDII
cable to the OBDII
port, and route the
cable under the dash,
out the side panel, up between the door seal trim
and the edge of the dash.
Tuck the cable back as far
as you can as you route it
up to the dash.
*Note: Leave 6-10”
of cable exposed on
top of the dash so you
have room to position the device.
Once you’ve identified
the suction cup position
on the windshield, use
the supplied alcohol wipe
to thoroughly clean the
area. After you’ve wiped
the area clean, let it dry
for 2-3 minutes.
Next, insert the connector on the end
of the OBDII cable into the 16-pin
connector on the back of the device
(this is easier if done prior to mounting the device on the window). The
connector only fits one way so be
sure that the locking tab is on the
bottom.
Note: The device will power on
automatically when it detects your
vehicle has started. If you wish to
power up the device without starting
your vehicle, ensure the key is in the
run position and touch the screen
(CTS) or a button (CS).
Step 5:
Position and Lock the Device on theWindshield
Once the alcohol has dried
you’re ready to attach the
mount to the windshield.
UNLOCKED
You’ll notice that the mount has
a locking tab. This tab creates the
suction that will lock the mount
to the windshield. Make sure
the lock is in the “Unlocked”
position. Position the
mount where you’ve
cleaned the windshield,
press firmly, and push the tab to the
“Locked” position.
Once you’ve locked the mount to
the windshield, use the adjustment
knobs to fine tune the viewing angle
and height of the the CTS/CS device.
LOCKED
VERTICAL ADJ.
KNOB
This knob will allow you
to adjust the viewing
angle and height of the
device up or down.
VARIABLE ANGLE ADJ
KNOB
This knob will allow you to adjust the viewing angle of the
device in both horizontal and
vertical fashions. Use it to fine
tune your viewing angle.
Step 6:
CS/CTS DEVICE DESCRIPTIONS
Verify Position and Viewing Placement
C T S L AY O U T
After you’ve locked the mount and the CS/CTS device is
in place on your windshield, sit back in your drivers seat
and make sure the viewing angle is as desired. Check
to make sure the device doesn’t create a blind spot that
may impair your view of the road/traffic/pedestrians from the drivers seat.
*Note: Some states prohibit mounting devices
CS/CTS MAIN MENU
2
3
4
5
6
3
3. Power level up/down Arrows - On the ATTITUDE (with JUICE) these buttons are used to toggle the
4.
1
5.
6.
7.
8.
9.
10.
For Operating Instructions and trouble shooting please refer to the User Guide found
in the folder packet that came with your CS or CTS package. For additional questions
not found in the User Guide you can call:
Edge Products Technical Support
Hours Mon-Friday
8:00 a.m. - 5:00 p.m. Mountain Standard Time
1-888-360-EDGE (3343)
•
touching the gauge and choosing a different parameter from the drop down list. Use this menu to choose a
new PID, change alert settings, and choose a new gauge color.
7
that may obstruct your view. Please check local
and state laws to ensure compliance.
For alternate mounting options visit
www.edgeproducts.com or www.arkon.com
After positioning the device
and the mount, remove any
slack in the OBDII cable and
coil it behind the side panel
you removed earlier. Use the
supplied zip ties to secure the
coiled cable from moving or
falling down under the dash, or
interfering with pedal operation.
Replace all panels removed during
installation
THE MAIN MENU CONSISTS
OF SIX OPTIONS:
1. Main Menu button - The main menu button gives you access to the main menu.
2. Left Gauge - The left analog gauge. The displayed parameter for all gauges can be changed by simply
8
10
9
power level up/down as well as navigation in the menus. On the EVOLUTION and INSIGHT, these buttons may
be used for future feature enhancements.
Alert Indicator - The alert indicator light will illuminate (red) when an alert limit is exceeded. When this
light contains an “R,” it indicates that your Diesel Particulate Filter (DPF) equipped vehicle is performing a
regeneration cycle.
Power Level Indicator - The power level indicator represents the current power level. 0 represents
stock. I stands for Insight which produces no additional horsepower.
Back-down Indicator - (ATTITUDE with JUICE) The back-down indicator light will illuminate (yellow)
when the Juice module is decreasing power added by the device, when approaching or exceeding the backdown set point limit.
Right Gauge - The right analog gauge.
Lower Left Gauge - The lower left digital gauge.
Center Gauge - The Center analog gauge.
Lower Right Gauge - The lower right digital gauge.
C S L AY O U T
1. Up/Down Arrow Button - On the ATTITUDE (with JUICE) these buttons are used to toggle the power
1
2
3
4
5
6
7
2.
3.
4.
level up/down. On the EVOLUTION, and INSIGHT these buttons may be used for future feature enhancements.
In the menus these buttons are used to select the menu items and increase or decrease values.
Menu Button - The menu button gives you access to the main menu or can be used to exit out of a menu
screen.
Left Gauge - The left analog gauge. The displayed parameter for all gauges can be changed by pressing
the enter button, choosing the desired gauge, and selecting a different parameter from the drop down list.
Alert Indicator - The alert indicator light will illuminate (red) when an alert limit is exceeded. When this
light contains an “R,” it indicates that your Diesel Particulate Filter (DPF) equipped vehicle is performing a
regeneration cycle.
5. Power Level Indicator - The power level indicator represents the current power level. 0 represents
stock. I stands for Insight which produces no additional horsepower.
•
•
MENU NAVIGATION BUTTONS
•
Both the CS and CTS devices provide you with the
following three buttons for navigating the menu
system:
Menu: The Menu button allows you to enter the main menu
•
(CS only). Once you are in the menu system you’ll use the Menu
button to return to the previous screen.
UP/Down Arrow: The Up/Down Arrow buttons will allow
you to toggle up or down through the menu options. Each
option will be highlighted as you toggle.
Enter: Pressing the Enter button will select the currently
highlighted option.
*Note: With the CTS device you can simply touch the option
you’d like to select on the menu screen. As a touch screen
device it will automatically select the option you’ve touched
and advance you to the selected option screen.
•
•
•
View Camera - This gives you access to the camera if installed on your
vehicle. (CTS only)
Show alerts - This item shows the
alert grid screen. *NOTE: This menu
only appears when there is an alert
active
Programming - This allows you
to program the vehicle to one of the
pre-tuned levels included only with
the Evolution.
Juice Control - This gives you
access to the power and drive train
performance options through the
Edge Juice only with the Attitude.
Diagnostics - This gives you the
ability to retrieve and clear trouble
codes, as well as other diagnostic
functions depending on vehicle.
Options - This gives you access
to multiple device settings (i.e.
alert settings, sound duration,
backlight-autodim etc).
Help - This is used to display product
information, vehicle information,
technical support tools, and contact
information.
Hot Unlocker - This allows you to
add a HOT power level. (Attitude only)
CS/CTS ACCESSORIES
Multiple accessories are available for
the CS/CTS device. Accessories
include EGT sensors, back-up
camera, and vehicle-specific
custom mounting solutions.
6. Back-down Indicator 7.
8.
8
9
9.
(ATTITUDE with JUICE) The back-down indicator light will illuminate (yellow)
when the Juice module is decreasing power added by the device, when approaching or exceeding the backdown set point limit.
Right Gauge - The right analog gauge.
Enter Button - The enter button when pressed from the main screen will allow you to change the gauge
parameters (PID, Alert Settings, and Gauge Color). In the menus it allows you to select the highlighted option.
Center Gauge - The center gauge.
For more information and
pricing please visit
Copyright © 2010 REV 01
ACCESSORIES PORT
VIDEO IN PORT (CTS ONLY)
Open as PDF
Similar pages