SmartSwitch Upgrade/Replacement Instructions

SmartSwitch Upgrade/Replacement Instructions
These instructions explain how to install a SmartSwitch Service/System Selector (SmartSwitch)
to upgrade a TracVision HD11 system (with one HD11 antenna and ACU) or replace a
previously installed SmartSwitch.
IMPORTANT!
For instructions on installing the SmartSwitch and one or two TracVision HD11 systems
together, refer to the TracVision HD11 Installation Guide. For SmartSwitch operation
instructions, refer to the TracVision HD11 User’s Guide.
Installation Steps
1. Inspect Parts and Gather Tools............................ 3
2. Plan the Installation............................................... 4
3. Mount the SmartSwitch........................................ 5
4. Wire the SmartSwitch ........................................... 7
5. Launch the Setup Wizard (Upgrades Only) ...... 8
6. Turn Off Search Modes (Upgrades Only).......... 9
Who Should Install the System?
To ensure a safe and effective installation, KVH requires that a KVH-certified marine technician
install the SmartSwitch. KVH-certified technicians have the tools and electronics expertise
necessary to install the system. To find a technician near you, visit www.kvh.com/
wheretogetservice.
Technical Support
If you need technical assistance, please contact KVH Technical Support:
Europe, Middle East, Africa, Asia
Phone: +45 45 160 180
E-mail: support@kvh.dk
(Mon.-Fri., 8 am-4:30 pm, +1 GMT)
North/South America, Australia, New Zealand
Phone: +1 401 847-3327
E-mail: techs@kvh.com
(Mon.-Fri., 9 am-6 pm ET, -5 GMT)
(Sat., 9 am-2 pm ET, -5 GMT)
KVH, TracVision, and the unique light-colored dome with dark contrasting baseplate are registered trademarks of KVH Industries, Inc.
All other trademarks are property of their respective companies. The information in this document is subject to change without notice.
No company shall be liable for errors contained herein. ©2012-2015 KVH Industries, Inc., All rights reserved. 54-0816 Rev.C
1
1 Inspect Parts and Gather Tools
Before you begin, follow these steps to make sure
you have everything you need to complete the
installation.
a. Unpack the box and ensure it contains
everything shown on the Kitpack Contents
List.
Figure 1 SmartSwitch
®
POWER
•
PC (preferably with Internet access)
•
16.31"
(41.43 cm)
Strain Relief Bracket
c. Gather the following tools. You will need
these tools to complete the installation.
#1 Phillips screwdriver
PORT/A
STBD/B
ANTENNA INPUT
2
3
MULTISWITCH OUT
Figure 2 SmartSwitch Dimensions
b. Carefully examine all of the supplied parts to
ensure nothing was damaged in shipment.
•
1
Top View
7/16" wrench
11.18"
(28.40 cm)
IMPORTANT!
Some SmartSwitch connectors include
connector terminators. Only remove
terminators from connectors you will be
wiring to (see “Wiring Diagrams” on
page 11).
19.00"
(48.26 cm)
Side View
2.63"
(6.68 cm)
1.75"
(4.45 cm)
Front View
4 x ø.25"
(0.64 cm)
16.75"
(42.55 cm)
18.31"
(46.51 cm)
0.44"
(1.12 cm)
3
2 Plan the Installation
Follow the steps below to plan the SmartSwitch
installation.
Select an Installation Location
Figure 3 SmartSwitch Mounting Options
SmartSwitch Rack Mount
®
POWER
1
PORT/A
STBD/B
ANTENNA INPUT
2
3
MULTISWITCH OUT
When selecting an installation location, consider
the following:
•
•
Choose a Mounting Option
Select one of the following SmartSwitch
mounting options.
4
Rack Mounting
Bracket (x2)
Choose a belowdecks installation location
that is dry, well-ventilated, and away from
any heat sources or salt spray.
The SmartSwitch must be installed within
3 feet (1 m) of the ACU A (the TracVision
HD11 Antenna Control Unit (ACU)
connected to Antenna A) in order to use the
supplied PC data cable (25 ft (7.6 m)
maximum). However, longer cabling may be
used – contact KVH for details.
•
You can mount the SmartSwitch in a
standard 19" (48.26 cm) equipment rack,
either separately or together with an ACU
(see Figure 3). The SmartSwitch is 1.5U in
height.
•
Alternatively, you can mount the
SmartSwitch to a horizontal surface; the
horizontal surface mounting brackets can
attach to either the top or bottom of the
SmartSwitch (see Figure 3).
1.5U
ACU/SmartSwitch Joint Rack Mount
TRAC KING
DIRE CTV
®
CONTROL UNIT
MENU
CHANGE
S ATS
99/101/103
ACCEPT
EXIT
ANTENNA
POWER
3U
®
POWER
1
2
3
MULTISWITCH OUT
PORT/A
STBD/B
ANTENNA INPUT
Joint Rack
Mounting Bracket (x2)
SmartSwitch Horizontal Surface Mount
®
POWER
1
2
3
MULTISWITCH OUT
PORT/A
STBD/B
ANTENNA INPUT
Horizontal Surface
Mounting Bracket (x2)
3 Mount the SmartSwitch
Follow the steps below to mount the
SmartSwitch using the desired mounting option.
Figure 4 Strain-Relief Bracket Mounting
Rack Mounting
a. Attach the strain-relief bracket to the
SmartSwitch, as shown in Figure 4. Using a
#1 Phillips screwdriver, secure the bracket in
place using four #6-32 screws and #6 washers
(supplied in the kitpack).
b. Secure the SmartSwitch to the rack using four
M6 screws and washers (see Figure 5).
#6-32
Screw (x4)
#6 Washer
(x4)
Figure 5 SmartSwitch Rack Mounting
Mounting
Hole (x4)
Horizontal Mounting
a. Using a #1 Phillips screwdriver, remove the
six screws securing the rack mounting
brackets to the SmartSwitch (see Figure 6).
b. Using a #1 Phillips screwdriver, attach the
two horizontal mounting brackets to the sides
of the SmartSwitch using four supplied
#6-32 screws and #6 washers (see Figure 7).
You can attach the brackets to either the top
or bottom of the SmartSwitch, depending on
your desired mounting location.
c. If you are mounting the SmartSwitch to the
underside of a shelf, attach the strain-relief
bracket, as shown in Figure 4. Using a #1
Phillips screwdriver, secure the bracket in
place using four #6-32 screws and #6 washers
(supplied in the kitpack).
d. Using fasteners appropriate for the mounting
surface, secure the SmartSwitch to the
mounting surface using the four mounting
bracket holes.
Strain-Relief
Bracket
®
POWER
1
2
3
MULTISWITCH OUT
PORT/A
STBD/B
ANTENNA INPUT
M6 Screw
and Washer (x4)
Figure 6 SmartSwitch Rack Mounting Bracket Removal
Rack Mounting
Bracket (x2)
#6-32 Screw (x6)
Figure 7 Horizontal Mounting
Horizontal
Mounting Bracket (x2)
#6 Washer
(x6)
Strain-Relief
Bracket
#6-32
Screw (x6)
5
3 Continued Mount the SmartSwitch
Joint ACU/SmartSwitch Rack Mounting
a. Using a #1 Phillips screwdriver, remove the
six screws securing the rack mounting
brackets to the SmartSwitch (see Figure 6 on
page 5).
b. Repeat Step a. to remove the six screws
securing the rack mounting brackets to the
ACU.
c. Attach the joint rack mounting brackets to the
ACU and SmartSwitch, as shown in Figure 8.
Secure the brackets in place using twelve
#6-32 screws and washers (supplied in the
kitpacks).
d. Attach the strain-relief bracket and retaining
straps, as shown in Figure 8. Secure them in
place using eight #6-32 screws and
#6 washers (supplied in the kitpacks).
NOTE: Only the SmartSwitch strain-relief bracket
must be installed. The ACU does not require a strainrelief bracket when jointly mounted with the
SmartSwitch.
e. Secure the joint assembly to the rack using
four M6 screws and washers.
6
Figure 8 ACU/SmartSwitch Joint Assembly
ACU
Joint Rack
Mounting
Bracket (x2)
SmartSwitch
#6-32 Screw
(x20)
#6 Washer
(x20)
Retaining
Strap (x2)
Strain-Relief
Bracket
4 Wire the SmartSwitch
Antenna A
Antenna B
(If equipped)
ACU A
B (+)
A (–)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA
Blue/White
White/Blue
Orange/White
White/Orange
Gray/White
Red (+48V)
SmartSwitch
Controller
Brown/White
To Antenna
Wire Color/Stripe Color
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
Black (Gnd)
NOTE: When connecting cables, first hand-tighten
the connector, then tighten 1/4 turn using a 7/16"
wrench.
Figure 9 Wiring Overview
White/Gray
Wiring instructions vary according to the
customer’s specific system configuration and
hardware. Refer to the wiring diagrams
provided in Appendix A on page 11 for
complete wiring instructions.
CAUTION
Maintenance
RS232
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Meets
requirements
WiFi
Tested to comply
with FCC Standards
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Fuse 3.15A 250V ~ Fast Acting
ACU B
B (+)
A (–)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA
Blue/White
White/Blue
Orange/White
White/Orange
Gray/White
Red (+48V)
Black (Gnd)
SmartSwitch
Controller
Brown/White
To Antenna
Wire Color/Stripe Color
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
White/Gray
NOTE: Be sure to apply the cable labels (supplied in
the kitpack) to the cables that will connect the
SmartSwitch to other system components.
KVH and TracVision are registered
trademarks of KVH Industries, Inc.
CAUTION
Maintenance
RS232
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Meets
requirements
WiFi
Tested to comply
with FCC Standards
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Fuse 3.15A 250V ~ Fast Acting
KVH and TracVision are registered
trademarks of KVH Industries, Inc.
Wiring SWM and Non-SWM Hardware
Only DIRECTV® programming in North
America supports SWM-compatible receivers
and DVRs (see Figure 10). All linear receivers/
DVRs and other circular receivers/DVRs are not
SWM-compatible.
SmartSwitch
PORT/A ANTENNA INPUT
13V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 1
13V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 3
13V
18V/22KHZ 13V/22KHZ
Receiver/DVR Receiver/DVR Receiver/DVR
Group 1
Group 2
Group 3
IMPORTANT!
Unless specified otherwise, receivers/DVRs
in the following wiring diagrams are not
SWM-compatible.
STARBOARD/B ANTENNA INPUT
TO ACU
18V
18V
Figure 10 SWM-Compatible Receivers/DVRs
Receivers
DVRs
NOTE: Additional SWM-compatible receivers/DVRs
might become available at any time. If your receiver or
DVR model is not listed here, check its manual to see
if it is SWM-compatible.
H20
HR21, HR21 Pro
H21
HR22
H22
HR23
SmartSwitch Input Wiring Diagrams
H23
HR24
H24
HR34/HMC*
H25
R16
D12
R20
D13
R22
•
One TracVision HD11 Antenna/ACU (see
page 11)
•
Two TracVision HD11 Antennas/ACUs (see
page 12)
SmartSwitch Output Wiring Diagrams
•
Overview (see page 13)
•
32 Non-SWM-compatible Tuners (see
page 14)
•
16 SWM-compatible Tuners and 32 NonSWM-compatible Tuners (see page 15)
•
32 SWM-compatible Tuners and 32 NonSWM-compatible Tuners (see page 16)
*NOTE: Unlike other DVRs, the HR34 Home Media
Center uses five tuners. Therefore, if you connect this
DVR, be sure to reserve five tuners instead of two.
Refer to the DVR’s manual for complete wiring
details.
7
5 Launch the Setup Wizard (Upgrades Only)
If you are upgrading the TracVision HD11
system to include a SmartSwitch, follow the steps
below to launch the Setup Wizard and
reconfigure system settings. If you are replacing
a previously installed SmartSwitch, the
procedure is complete (your system is already
configured).
a. Press the power button on the front of the
ACU to apply power to the TracVision
system. Then wait up to 5 minutes for system
startup.
b. Open the web browser on a PC connected to
the same network. Then type the ACU’s
serial number into the browser’s address bar,
as shown below:
http://hd11-<ACU serial number>.local
NOTE: For example, if the serial number was
123456789, you would enter the following into the
browser’s address bar: http://hd11-123456789.local
Figure 11 ACU Power Button
TRACKING
DIRECTV
®
CONTROL UNIT
MENU
ACCEPT
EXIT
Power
Button
Figure 12 ACU Serial Number Location
T R AC K I N G
D I R E C T V
®
CONTROL UNIT
MENU
CHANGE
S AT S
9 9 / 1 0 1 / 1 0 3
ACCEPT
EXIT
ANTENNA
POWER
123456789
Serial Number
on Rear Panel
Figure 13 Launch Setup Wizard Button
c. Log into the web interface.
NOTE: The default login credentials are:
Username: admin
Password: password
d. Select Settings/General Settings. Then select the
“Launch” Button to launch the Setup Wizard
(see Figure 13).
8
S ATS
99/101/103
POWER
TIP: The ACU serial number location is shown in
Figure 12.
e. Follow the Setup Wizard’s onscreen
instructions to reconfigure system settings
(see Figure 14).
CHANGE
ANTENNA
Figure 14 Setup Wizard
6 Turn Off Search Modes (Upgrades Only)
If you are upgrading a TracVision HD11 dualantenna system to include a SmartSwitch, follow
the steps below to turn off Search Modes 1 and 2
on each antenna. If you are replacing a
previously installed dual-antenna system
SmartSwitch, the procedure is complete (the
search modes have already been turned off).
a. Open the web browser on a PC connected to
the same network as the HD11 antennas.
Open two web browser windows or tabs. In
the first web browser window/tab, enter the
IP address of the "A" (master) antenna's ACU.
In the second window/tab, enter the IP
address of the "B" (slave) antenna's ACU.
(Alternatively, you can enter http://hd11<ACU serial number>.local instead of the IP
address.)
Figure 15 Command Line
Figure 16 +HDT (True Heading) Message
NOTE: You can view an ACU's IP address and serial
number on the ACU's front panel under its "About
System" menu.
b. Log into the HD11 web interface for each
antenna:
Username: admin
Password: password
c. At the web interface for each antenna, select
the Support tab. Then select Command Line
(see Figure 15).
d. Look for the +HDT (true heading) message in
each antenna’s data stream (see Figure 16).
Make sure that both antennas report the same
heading. If they don’t, make sure the ACU for
each antenna is connected to the same
heading source (NMEA 0183 talker), and the
device is configured to transmit the $--HDT
message.
Figure 17 Tracked Satellite
IMPORTANT!
Do not proceed with the rest of this procedure
until both antennas are reporting the same
heading.
e. Return to the Support: Home page and make
sure that both antennas are tracking the same
satellite (see Figure 17). If they are, complete
the remaining steps in this section at the web
interface for each antenna.
9
6 Continued Turn Off Search Modes
NOTE: If both antennas cannot track the same
satellite due to a blockage condition, first select a
satellite that the “A” (master) antenna can track and
follow all of the remaining steps for just the “A”
(master) antenna. When you have completed the entire
procedure for the “A” (master) antenna, switch to a
satellite that the “B” (slave) antenna can track then
repeat all of the steps for the “B” (slave) antenna.
Figure 18 AZOFFSET Value
IMPORTANT!
To complete the remaining steps of this
procedure, the antenna must be tracking a
satellite.
f.
Select Command Line.
g. In the Command box, enter AZOFFSET.
Then click Send. Verify that an "AZOFFSET"
value is reported along with a "V" as shown
in Figure 18 (indicating a valid azimuth offset
value). It might take up to 30 minutes if the
antenna was just installed.
h. In the Command box, enter SM1,OFF as
shown in Figure 19. Then click Send. Verify
that “SM1,OFF” appears in the data stream
(indicating Search Mode 1 is turned off).
i.
In the Command box, enter SM2,OFF as
shown in Figure 19. Then click Send. Verify
that “SM2,OFF” appears in the data stream
(indicating Search Mode 2 is turned off).
If both antennas could not track the same satellite
(see note that follows step e), switch to a satellite
that the "B" (slave) antenna can track and repeat
steps f-i for the "B" (slave) antenna while it is
tracking a satellite.
10
Figure 19 Turn Off Search Modes
A Wiring Diagrams
Appendix
Wiring SmartSwitch Input: One TracVision HD11 Antenna/ACU
Antenna
18V
Power/Data
13V
18V/
22KHz
Network
ACU
13V/
22KHz
Terminal Strip
A (–)
B (+)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA
Blue/White
White/Blue
Black (Gnd)
Orange/White
Red (+48V)
White/Orange
Gray/White
White/Gray
Brown/White
To Antenna
Wire Color/Stripe Color
SmartSwitch
Controller
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
Maintenance
RS232
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Meets
requirements
WiFi
Tested to comply
with FCC Standards
Fuse 3.15A 250V ~ Fast Acting
Power
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
KVH and TracVision are registered
trademarks of KVH Industries, Inc.
SmartSwitch
Controller
Ferrite Clamp
18V
13V
13V/
18V/
22KHz 22KHz
Connect Cable End with
Ferrite Clamp to ACU
SmartSwitch
PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT
TO ACU
18V
18V
13V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 1
13V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 3
13V
To ACU
18V/22KHZ 13V/22KHZ
11
A Continued Wiring Diagrams
Wiring SmartSwitch Input: Two TracVision HD11 Antennas/ACUs
Starboard Antenna (B)
Port Antenna (A)
Power/Data
Power/Data
13V/
22KHz
18V
18V/
22KHz
13V
SmartSwitch
18V/
22KHz
13V
13V/
22KHz
18V
18V/
22KHz
13V
18V/
22KHz
13V
13V/
22KHz
18V
13V/
22KHz
18V
PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT
TO ACU
18V
13V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 1
18V
13V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 3
13V
To ACU
18V/22KHZ 13V/22KHZ
Ferrite Clamp
Port ACU (A) (Master)
Terminal Strip
Connect Cable End with
Ferrite Clamp to ACU
A (–)
B (+)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA
Blue/White
White/Blue
Orange/White
White/Orange
Gray/White
White/Gray
Red (+48V)
Black (Gnd)
SmartSwitch
Controller
Brown/White
To Antenna
Wire Color/Stripe Color
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
Maintenance
RS232
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Meets
requirements
WiFi
Tested to comply
with FCC Standards
Fuse 3.15A 250V ~ Fast Acting
Power
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
KVH and TracVision are registered
trademarks of KVH Industries, Inc.
SmartSwitch
Controller
Network
Starboard ACU (B) (Slave)
Terminal Strip
A (–)
B (+)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA
Blue/White
White/Blue
Orange/White
White/Orange
Gray/White
White/Gray
Black (Gnd)
Red (+48V)
SmartSwitch
Controller
Brown/White
To Antenna
Wire Color/Stripe Color
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
Maintenance
RS232
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Meets
requirements
Tested to comply
with FCC Standards
Fuse 3.15A 250V ~ Fast Acting
Power
Network
12
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device must not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
KVH and TracVision are registered
trademarks of KVH Industries, Inc.
WiFi
A Continued Wiring Diagrams
Wiring SmartSwitch Output: Overview
SmartSwitch
Example: Wiring two non-SWM-compatible
receiver/DVR groups and one SWMcompatible receiver/DVR group
PORT/A ANTENNA INPUT
18V
13V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 1
13V
18V/22KHZ 13V/22KHZ
Multiswitch Out 1
Region/Service Provider #1
STARBOARD/B ANTENNA INPUT
TO ACU
18V
18V
18V
32-Output Multiswitch*
13V
18V/22KHZ 13V/22KHZ
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 3
18V
Multiswitch Out 2
Region/Service Provider #2
Power
Supply
13V
MULTISWITCH OUT 2
13V
18V/22KHZ 13V/22KHZ
Multiswitch Out 3
DIRECTV SWM Hardware
Power
Supply
16-Tuner
SWM
Expander**
32-Output Multiswitch*
Power
to SWM
SWM-E2
GND
24 VDC IN
+
18V
Non-SWM Receivers/DVRs
(Linear, DIRECTV Latin America, DISH
Network®, Bell TV, and legacy DIRECTV
receivers)
13V
18V/22kHz
Sat 99°/101°
Sat 103°/110°/119°
Flex
13V/22kHz
Sat 103°/110°/119° Port 1
Flex
Port 2
Non-SWM Receivers/DVRs
(DIRECTV Latin America, DISH
Network, Bell TV, and legacy DIRECTV
receivers)
8-Way Splitter
SWM Receivers/DVRs
8-Way Splitter
SWM Receivers/DVRs
*NOTE: Similar connections apply to 16-output and 8-output multiswitches
**NOTE: Similar connections apply to 32-tuner SWM expanders
13
A Continued Wiring Diagrams
Wiring SmartSwitch Output: 32 Non-SWM-compatible Tuners
SmartSwitch
PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT
TO ACU
18V
18V
13V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 1
13V
18V/22KHZ 13V/22KHZ
18V 13V
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 3
13V
18V/22KHZ 13V/22KHZ
13V/
22KHz
18V/
22KHz
18V/ 13V/
13V 22KHz 22KHz
18V
32-Output Multiswitch
NOTE: Connections shown on this multiswitch also
apply to 16-output and 8-output multiswitches
Additional Receivers/DVRs
Receiver
Satellite In
TV/ANTENNA/
CABLE IN
SATELLITE IN
14
R AUDIO
L
VIDEO
ETHERNET
DIGITAL AUDIO
OUTPUT
TV SET
OUT
Pb
Pr
Y
S-VIDEO
USB
PHONE
Power
Supply
A Continued Wiring Diagrams
Wiring SmartSwitch Output: 16 SWM-compatible Tuners and 32 Non-SWM-compatible Tuners
16-Tuner SWM Expander
SWM1/PWR
SWM1/PWR
Legacy 1
Optional - To 8-Way Splitter
Legacy 2
24 VDC IN
+
Power
to SWM
Refer to the
instructions in the
SWM Expander Kit
for complete wiring
information
GND
SWM-E2
18V
Input
18V 13V
Splitter
Flex
Port 2
Splitter
Out
Out
13V/
22KHz
18V/
22KHz
Out
SmartSwitch
PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT
TO ACU
18V
18V
13V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 1
13V
18V
13V
18V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 3
13V
18V/22KHZ 13V/22KHZ
13V/
22KHz
18V/
22KHz
18V/ 13V/
13V 22KHz 22KHz
Power
Supply
32-Output Multiswitch
NOTE: Connections shown on this multiswitch also
apply to 16-output and 8-output multiswitches
8-Way Splitter
Non-SWM Receivers/DVRs
(DIRECTV Latin America, DISH Network,
Bell TV, and legacy DIRECTV receivers)
Satellite In DIRECTV
(SWM-1) SWM Receiver
COMPONENT OUT
SATELLITE IN
(SWM-1)
S-VIDEO OUT
USB
VIDEO OUT
Out
Flex
13V/22kHz
Sat 103°/110°/119° Port 1
13V
18V/22kHz
Sat 99°/101°
Sat 103°/110°/119°
Input
DIGITAL AUDIO
OUT OPTICAL
AUDIO OUT
ETHERNET
PHONE JACK
HDMI OUT
Supports up to 7 Additional Tuners
Each SWM Receiver = 1 Tuner
Each DVR = 2 Tuners
15
A Continued Wiring Diagrams
Wiring SmartSwitch Output: 32 SWM-compatible Tuners and 32 Non-SWM-compatible Tuners
32-Tuner SWM Expander
SWM1/PWR
SWM1/PWR
Legacy 1
Optional - To 8-Way Splitter
Legacy 2
Optional - To 8-Way Splitter
24 VDC IN
+
Refer to the
instructions in the
SWM Expander Kit
for complete wiring
information
24 VDC IN
+
Power
to SWM
Power
to SWM
GND
SWM-E4
18V
Flex
13V/22kHz
Sat 103°/110°/119° Port 1
13V
18V/22kHz
Sat 99°/101°
Sat 103°/110°/119°
18V 13V
Flex
Port 2
13V/
22KHz
Optional - To 8-Way Splitter
18V/
22KHz
Legacy 2
Legacy 1
SWM1/PWR
SWM1/PWR
SmartSwitch
PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT
TO ACU
18V
18V
13V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 1
13V
18V
13V
18V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ
MULTISWITCH OUT 3
13V
18V/22KHZ 13V/22KHZ
13V/
22KHz
18V/
22KHz
18V/ 13V/
13V 22KHz 22KHz
Power
Supply
32-Output Multiswitch
NOTE: Connections shown on this multiswitch also
apply to 16-output and 8-output multiswitches
8-Way Splitter
COMPONENT OUT
SATELLITE IN
(SWM-1)
S-VIDEO OUT
USB
VIDEO OUT
Non-SWM Receivers/DVRs
(DIRECTV Latin America, DISH Network,
Bell TV, and legacy DIRECTV receivers)
Satellite In DIRECTV
(SWM-1) SWM Receiver
DIGITAL AUDIO
OUT OPTICAL
AUDIO OUT
HDMI OUT
Supports up to 7 Additional Tuners
Each SWM Receiver = 1 Tuner
Each DVR = 2 Tuners
16
ETHERNET
PHONE JACK
Open as PDF
Similar pages