Installation instructions for part 99-8257
Scion Multi-kit 2004-2015
99-8257
KIT FEATURES
• DIN radio provision with pocket
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
TOOLS REQUIRED
• Cutting tool • Phillips screwdriver
• 10mm socket wrench • Grinder • Panel removal tool
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-1761
Antenna Adapter: • Not required
KIT COMPONENTS
• A) Radio housing • B) Bracket Set 1 • C) Bracket Set 2 • D) ISO DIN brackets • E) ISO DDIN radio brackets
• F) ISO DIN trim plate • G) DIN spacer
REV. 6/28/2016 INST99-8257
A
E
B
F
C
D
G
CAUTION! All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
APPLICATIONS
See application list inside cover
METRA. The World’s best kits.™
metraonline.com
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
99-8257
Applications
SCION
tC2005-2010
tC2011-2016*
xA2004-2006
Table of Contents
Dash Disassembly.............................................................................................3-8
xB2004-2015
xD2008-2014
–. tC 2005-2010..................................................................................................... 3
–. tC 2011-2016..................................................................................................... 4
–. xA 2004-2006..................................................................................................... 5
* ISO DDIN radio provision only
–. xB 2004-2006.................................................................................................... 6
–. xB 2008-2015.................................................................................................... 7
–. xD 2008-2014.................................................................................................... 8
Kit Assembly
–. DIN radio provision with pocket........................................................................... 9
–. ISO DIN radio provision with pocket................................................................... 10
–. ISO DDIN radio provision................................................................................... 11
2
99-8257
Dash Disassembly
Scion tC 2005-2010
1. Unsnap trim from around shifter
(not necessary to be removed).
(Figure A)
2. Unclip and remove panel from
around radio. (Including climate
controls and radio door). (Figure B)
3. Remove (2) 10mm nuts from the
top B mounting locations and
(2) 10mm bolts from the bottom
mounting locations to remove the
radio. (Figure C)
(Figure B)
(Figure A)
4. If installing a ISO DDIN aftermarket
radio, remove factory brackets
from radio. Retain brackets for use
during kit assembly.
Continue to kit assembly
3
(Figure C)
99-8257
Dash Disassembly
Scion tC 2011-2016
1. Unclip and remove the radio trim
panel. (Figure A)
2. Remove (4) 10mm bolts securing
the radio. (Figure B)
3. If installing a ISO DDIN aftermarket
radio, remove factory brackets
from radio. Retain brackets for use
during kit assembly.
Continue to kit assembly
(Figure A)
(Figure B)
4
99-8257
Dash Disassembly
Scion xA 2004-2006
1. Pull outward on the (3) climate
control knobs and remove. (Figure A)
OFF
HI
OFF
HI
2. Remove (2) Phillips screws from
behind the outer two climate
knobs. (Figure B)
3. Unsnap and remove the trim
pieces on each side of the climate
control/ashtray/pocket assembly.
(Figure C)
4. Remove (2) phillips screws from
the bottom of the climate control/
radio trim panel and unsnap and
remove the entire panel. (Figure D)
(Figure A)
(Figure C)
OFF
HI
5. Remove (4) Phillips screws to
remove the factory radio.
OFF
HI
6. If installing a ISO DDIN aftermarket
radio, remove factory brackets
from radio. Retain brackets for use
during kit assembly.
Continue to kit assembly
(Figure B)
(Figure D)
5
99-8257
Dash Disassembly
Scion xB 2004-2006
1. Pull outward on the (3) climate
control knobs and remove. (Figure A)
OFF
OFF
HI
2. Remove (2) Phillips screws from
behind the outer (2) knobs. (Figure B)
HI
OFF
HI
3. Unsnap and remove the entire
panel B surrounding the climate
controls and the radio. (Figure C)
4. Remove (4) Phillips screws to
remove the factory radio.
(Figure A)
(Figure B)
5. If installing a ISO DDIN aftermarket
radio, remove factory brackets
from radio. Retain brackets for use
during kit assembly.
Continue to kit assembly
6
(Figure C)
99-8257
Dash Disassembly
Scion xB 2008-2015
1. Unclip and remove the trim panel
around the radio including the a/c
vents. (Figure A)
2. Unclip and remove the trim panel
at the bottom edge of the dash
cavity. (Figure B)
3. Remove (4) 10mm bolts securing
the radio. (Figure C)
4. If installing a ISO DDIN aftermarket
radio, remove factory brackets
from radio. Retain brackets for use
during kit assembly.
(Figure A)
(Figure B)
Continue to kit assembly
7
(Figure C)
99-8257
Dash Disassembly
Scion xD 2008-2014
1. Unclip radio trim panel. Unplug and
remove panel. (Figure A)
2. Remove (4) Phillips screws
securing the radio. Unplug and
remove radio. (Figure B)
3. If installing a ISO DDIN aftermarket
radio, remove factory brackets
from radio. Retain brackets for use
during kit assembly. (Figure C)
(Figure A)
(Figure C)
Continue to kit assembly
(Figure B)
8
99-8257
Kit Assembly
DIN radio provision with pocket
1. Slide the mounting brackets onto the sides of the radio
housing until the side clips engage. (Figure A)
Note: Use Bracket Set 1 for xA, xB 2004-2006, and tC
2005-2010. Use Bracket Set 2 for the xB 2008-2015 and
xD 2008-2014.
2. For Bracket Set 1 cut and remove all mounting tabs
except the tabs being used for your application. (Figure B)
Note: Tabs are marked xA, xB and tC. For Bracket Set 2
skip to step 3.
3. Remove the metal DIN sleeve from the aftermarket radio.
4. Slide the sleeve into the radio housing and secure by
bending the metal locking tabs outward. (Figure C)
Note: A DIN spacer has been provided if extra depth is
required. This will go into the radio housing before the sleeve.
Side clips
(Figure A)
(Figure C)
Bracket
Set 1
5. Slide the aftermarket radio into the sleeve until it snaps
into place. (Figure D)
6. Locate the factory wiring harness and antenna connector in
the dash and complete all necessary connections to the radio.
Metra recommends using the proper mating adapter from
Metra and/or AXXESS. Test the radio for proper operation.
7. Secure the completed assembly into the dash, and then
reassemble the dash in reverse order of disassembly.
(Figure B)
(Figure D)
9
99-8257
Kit Assembly
ISO DIN radio provision with pocket
1. Slide the mounting brackets onto the sides of the radio
housing until the side clips engage. (Figure A)
Note: Use Bracket Set 1 for xA, xB 2004-2006, and tC 20052010. Use Bracket Set 2 for the xB 2008-2015 and xD 20082014.
2. For Bracket Set 1 cut and remove all mounting tabs except the
tabs being used for your application. (Figure B)
Note: Tabs are marked xA, xB and tC. For Bracket Set 2
skip to step 3.
3. Remove the metal DIN sleeve and trim ring from the
aftermarket radio.
4. Mount the ISO DIN brackets to the radio using the screws
supplied with the radio. (Figure C)
5. Slide the bracket/radio assembly into the radio housing until it
snaps into place. (Figure D)
6. Snap the ISO DIN trim plate onto the front of the radio housing.
(Figure D)
7. Locate the factory wiring harness and antenna connector in
the dash and complete all necessary connections to the radio.
Metra recommends using the proper mating adapter from
Metra and/or AXXESS. Test the radio for proper operation.
8. Secure the completed assembly into the dash, and then
reassemble the dash in reverse order of disassembly.
Side clips
(Figure A)
(Figure C)
Bracket
Set 1
(Figure B)
(Figure D)
10
99-8257
Kit Assembly
ISO DDIN radio provision
1. For Scion tC and xA models only: Cut off the front upper
section of the ISO DDIN brackets as shown. (Figure A)
2. Secure the factory mounting brackets, and the ISO DDIN
brackets to the radio with the screws supplied with the
radio. (Figure B)
Note: Remove the locating pins from the factory brackets
with a grinder.
3. Locate the factory wiring harness and antenna connector
in the dash and complete all necessary connections to
the radio. Metra recommends using the proper mating
adapter from Metra and/or AXXESS. Test the radio for
proper operation.
(Figure A)
(Figure B)
4. Secure the completed assembly into the dash, and then
reassemble the dash in reverse order of disassembly.
11
Installation instructions for part 99-8257
IMPORTANT
If you are having difficulties with the
installation of this product, please call our
Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a
second time, and make sure the installation
was performed exactly as the instructions
are stated. Please have the vehicle apart
and ready to perform troubleshooting steps
before calling.
KNOWLEDGE IS POWER
REV. 6/28/2016 INST99-8257
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
METRA. The World’s best kits.™
metraonline.com
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
Open as PDF
Similar pages