Briefed with the idea of “The Super intelligent Design Concept”
Sanji engineers developed the ZX Range of professional vehicle
security alarm and immobiliser systems. The SL range
represents the 'state of the art' in vehicle security. Read these
instructions for correct system operation. All points marked
are optional features.
*
1) SETTING THE
ALARM
2) DOOR / BOOT /
BONNET OPEN
WARNING
3) ALARM DELAY
PERIOD
To enable the
immobiliser
and full
alarm
features.
Press the lock button, the unit
will sound 2 soft chirps and the
indicators will flash twice. If
fitted with central locking the
doors will lock and the sensor
will switch on.
To warn the
driver that a
door or boot
is open when
setting the
alarm.
The unit will sound two
additional loud chirps and flash
the indicators twice when
setting the alarm. If a door is
still open when the unit fully
arms, the doors will be
bypassed. The system will
assume a faulty door switch.
25 second
arming delay.
The dash led will flash rapidly
during the 20 second delay
period. After the delay, the dash
led will start to flash slowly. The
alarm and immobiliser is now
fully armed.
8) SELECTIVE
UNLOCK ON
ALARM
RESET
To reset the
alarm and
open the
driver’s door
only.
Press the unlock button. The unit
will reset and selectively only
open the driver’s door. To open
the passenger doors press the
unlock button again.
9) AUTO ZONE
BYPASS
Automatically
bypass a
defective
zone.
If the unit detects a permanently
faulty zone, e.g. door or sensor
during alarm set, the system will
sound 3 times then isolate
the faulty zone.
*
10) VIOLATION
CHIRPS
11) STARTING
THE
VEHICLE
dash led
flashing
rapidly
5) ALARM ARMED
CONFIRMATION
To start the
vehicle after
the alarm has
been reset.
When the alarm is reset the
dash led will be off, the vehicle
can be started within 30
seconds. After 30 seconds the
immobiliser will be armed, dash
led on. Press the unlock button
the dash led will turn off, the
vehicle can now be started.
Automatic
locking of all
doors when
ignition is
turned on.
When the ignition is turned on, if
all the doors, boot and bonnet
are closed, the doors will lock.
To lock or
unlock the
doors from
the remote
while the car
is running.
Press the unlock button to
unlock the doors. Press the lock
button to lock the doors.
dash led
off
To skip the 25
second delay
period.
After the alarm has been set
press the lock button again. The
unit will now go to fully armed
and the dash led will flash
slowly.
dash led
flashing
slowly
To confirm
alarm armed
mode.
Press the lock button, the
indicators will flash once to
confirm that the alarm is fully
set.
When the alarm is reset, the
unit will sound 4 loud chirps
if the alarm had triggered during
the alarm set mode.
12) DOOR LOCK
ON START
*
13) DOOR LOCK
/ UNLOCK
IN DRIVE
UNLOCK
To temporarily
disable hi-jack.
In drive, (ignition on, dash led
off), press the lock and unlock
buttons simultaneously, the siren
will chirp once. Hi-jack is now
disabled. When the ignition is
turned on to drive, the unit will
flash the indicators once to warn
the user that the unit is in hijack service mode. To reactivate
hi-jack repeat the above
procedure, the siren will chirp
twice.
Forced hi-jack
in drive.
When you start the vehicle, the
unit will enter hi-jack, the dash
led will give a 1 second pulse.
Refer to point 21 to reset hi-jack.
If you start the vehicle with the
hidden button pressed, the unit
will not enter forced hi-jack.
To activate
hi-jack.
In drive open then close driver’s
door. If all doors, bonnet and
boot are closed the dash led will
give a 1 second pulse. The unit
has entered hi-jack phase.
Hi-jack mode.
Countdown period is 90 sec. If
ignition is turned off during this
time, the timer will stop. When
the ignition is turned on again
the timer will continue. If you try
to set the alarm during the
countdown period, the unit will
sound 4 loud chirps to warn you
that you are in hi-jack mode.
Hi-jack
warning
mode.
After the countdown period the
unit will enter the 20second
warning period. The unit will
chirp and flash the indicators.
After this period the unit will
enter the 8 second slow down
period. At any point in time you
can reset hi-jack by pressing the
hidden button.
To reset the
unit back to
normal drive
mode.
Press the hidden push button at
any time for +/- 2 seconds, the
unit will chirp once to confirm
that hi-jack has been reset.
To confirm
what phase
the unit is in.
In final hi-jack the siren will
sound on and off at 5 second
intervals and the indicators will
flash. The immobiliser will be
armed. The unit can be reset by
pushing the hidden button for
+/- 2 seconds.
*
Dash led
off
17) FORCED
HI-JACK
MODE
*
18) DRIVER’S
DOOR
HI-JACK
dash led
flashing
rapidly
4) ALARM FAST
ARM
To indicate to
user that the
alarm has
triggered
in his/her
absence.
16) HI-JACK
SERVICE
MODE
*
19) HI-JACK
OPERATION
*
20) HI-JACK
WARNING
PERIOD
*
LOCK
6) SENSOR SHUT
DOWN
7) RESETTING
THE ALARM
To disable the
interior sensor
so that a pet
or person can
remain inside
the vehicle
when the
alarm is set.
Press both buttons together
when setting the alarm. The
siren will sound 4 loud chirps
and the indicators will flash
twice. The sensor has now
been disabled (green LED will
turn off). After 25 seconds the
system will be fully armed.
To reset the
immobiliser
and alarm.
Press the unlock button. The
unit will sound 1 soft chirp and
the indicators will flash once. If
fitted with central locking the
doors will unlock.
14) DOOR
UNLOCK
ON IGNITION
OFF
To open the
doors when
the ignition is
turned off.
*
15) REMOTE
PANIC
To enable the
siren to
sound and the
indicators to
flash under
emergency
conditions.
Switch the ignition off. All the
doors will unlock. If fitted with
selective unlock, only the driver’s
door will open. Press the unlock
button to open the passenger
doors.
Press either button continuously
for +/- 3 seconds. When in panic,
the unit can be driven. Press the
unlock button to reset panic.
21) RESETTING
HI-JACK
*
22) FINAL
HI-JACK
*
23) ONE EVENT
OVERRIDE
24) PERMANENT
OVERRIDE
25) 1 WIRE
OVERRIDE
(speak to your
fitment center)
26) REMOVE
SET/RESET
CHIRPS
27) CARFINDER
To override
the
immobiliser
or alarm, in
the event of a
flat remote
battery.
To put the
unit into
permanent
override.
To put the
unit into
permanent
override.
Set / reset
chirps OFF.
Light up the
surrounding
area after
unlocking the
vehicle
In any mode, turn the Ignition on
and press the hidden push button
for +/- 2 seconds until the unit
chirps once, the system will be
reset. This is a once off
override.
In drive mode, press and hold the
hidden button (+/-10sec) until the
unit chirps once. The unit is now
in permanent override. The dash
led will flash continuously. The
alarm and immobiliser features
will now be dormant. If you try to
set the alarm you will hear 8
chirps. Repeat this procedure to
exit service mode.
NB: function only active when
Override wire connected.
Once override wire is connected
turn the ignition on and wait 2
seconds until the unit chirps once.
The unit is now in permanent
override. The dash led will flash
continuously. The alarm and
immobiliser features will now be
dormant. If you try to set the
alarm you will hear 8 chirps.
Simply disconnect the override
wire to exit service mode.
In drive mode press the hidden
button and turn the ignition off
immediately. Continue to press
the button until the unit chirps
once. The set / reset chirps have
now been removed. To turn the
set / reset chirps back on repeat
the above procedure, the unit will
chirp twice.
NB: Hardwire fitment option.
Press the unlock button
(ignition off). The vehicle will
unlock and turn the headlights or
indicators or interior dome light
on for 15 seconds. The lights will
switch off If ignition is switched
on within the 15 seconds.
28) AUTO ARM /
AUTO REARM
Automatically
arm the vehicle
and protect
your valuables
against
frequency
jammers
Once the auto arm feature has
been activated, the Sl300 will
auto arm from any state after
30 seconds.
1. From Set - If the alarm was set and the unlock
button was pressed with no doors opened, the
alarm will set the alarm and lock the doors.
FITMENT CENTER STAMP:
2. From Set - If the alarm was set and the unlock
button was pressed with a door opened, the
alarm will set the alarm but not lock the doors.
3. From Drive - once ignition is turned off, the
alarm will wait for the first door to be opened
then start the auto arm process.
NB: The driver can sit in the vehicle without the
alarm arming as long as the ignition is on. The
ACC (accessory) setting on the key switch does
not provide the ignition state required, the auto
arm feature will start if ignition is turned to ACC.
SL300-USER-REV0
Specifications subject to change without notice.
Sl300
The auto arm function looks for movement in the vehicle and will
always auto arm your vehicle. If you want to lock your vehicle
with someone or an animal in the vehicle, lock the vehicle
using the sensor shutdown option*.
*refer to point 6 of this manual.
ISO9001
Quality Company
SANJI SECURITY SYSTEMS (PTY) LTD
106 16TH ST MIDRAND GAUTENG, SOUTH AFRICA
TEL +27 11 266 7500 FAX +27 11 266 7501
E Mail : sales@sanji.co.za
http://www.sanji.co.za
Open as PDF
Similar pages