Camera
Camera MAC ID
Model WCO200NX
Installation Guide
twelve (12) characters (Will contain 0-9 and A-F only)
DO NOT plug in Ethernet or power until instructed during Nexia enrollment!
Front Panel View
3
1.Light Sensor. Detects light level to
enable night vision when required
2.Lens. No physical adjustment is
possible for the lens. Ensure lens
cover remains clean. Image quality
is degraded if lens cover is dirty or
smudged.
3.PIR Sensor. Detects motion
12v, 1.5A
Power Supply
Mounting Stand
USB to Ethernet Adapter
Anchor Screws
Rear Panel View
1. DC Power Input. Use supplied 12V / 1.5A
adapter.(Use seal and cap for weather resistance)
1
1
2
1. Log in to your account at www.mynexia.com.
2. Click Video tab.
3. Click the Edit Settings button next to the camera to be edited.
Rubber Seal
Screw Cap
Camera
3
4
2
You must have an active Nexia account. Verify Ethernet cable and
power cable are not plugged into the camera.
1. Log in to your account at www.mynexia.com.
2. Click Add Device button.
3. Click Cameras.
4. Click Enroll for the proper camera, and follow on-screen
instructions to complete the connection. (Note: Do not
disconnect cables during firmware update.)
5. Once connected, click Live Video to confirm successful video
connection.
6. To connect to WiFi, click Set up Wireless button . (Or you can
use WPS if your router supports this.).
7. Mount camera in desired viewing location.
Editing Camera Settings
Package Contents:
WCO200NX
Wireless HD Camera
FCC Statement
Enrolling Your Camera
5
6
2.
Microphone. Not supported by Nexia.
3.
Power LED.
On (Green) : Power on
Blinking (Green): Startup in process.
Blinking (Amber): Firmware update in process
On (Amber): Firmware update failed.
4.
Network LED. (Green, Amber)
On (Green): Connected to network.
Blinking (Green): Sending/receiving data
Off: Not connected to network.
Blinking (Amber): WPS in process
On (Amber): On for 5 seconds, WPS failed.
5.
WPS & Reset Button.
Use WPS to connect your camera to WiFi automatically. (Not supported on all routers.)
WPS: Tap WPS button on router, then tap and release camera’s WPS button
Reset: Not recommended unless instructed by Nexia. Press and hold button for 15 seconds. Camera will return to factory default
and will be unable to connect to its Nexia
account until added again.
6.
USB port. (Port at bottom of camera) Use
with supplied Ethernet adapter. Allows wired
connection to router.
Moving Your Camera to a Different Nexia Account
A camera cannot be on more than one Nexia account at the same. To
move a camera to a new account, follow these steps.
1. Go to www.mynexia.com and log in to the account to which the
camera is currently enrolled.
2. Click Video.
3. Click Remove This Camera for the camera you want to move.
4. After the camera has been successfully removed from this
account, it can be added to the new account using the Enroll
Camera steps above.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
the following measures:
●● Reorient or relocate the receiving antenna.
●● Increase the separation between the equipment and receiver.
●● Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
●● Consult the dealer or an experienced radio/TV technician for
help.
To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could void
the user’s authority to operate this equipment. (Example - use only
shielded interface cables when connecting to computer or peripheral
devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
Start Using Your Camera
●● View and record live video
●● View and download recorded videos
●● Automate video recording using Modes and Automations
●● For more information at mynexia.com, see Help, Cameras &
Video
Connection Troubleshooting
For a current list of camera connection and troubleshooting tips:
●● Go to www.mynexia.com
●● Click Help
●● Click Troubleshooting
●● Click Camera Troubleshooting
Mobile App Troubleshooting
If the camera is not displayed on the mobile app:
1. Log in to your account at www.mynexia.com
2. On the Dashboard, click on Mobile Devices
3. Click Edit Mobile Device
4. Click the selection box next to the camera
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
CE Approval
CE Standards
This product complies with the 99/5/EEC directives, including the
following safety and EMC standards:
●● EN55022/24
NexiaHome.com
U.S.A. /Canada
(877) 288-7707
Specifications
Dimensions (mounted)
3.3” (W) x 4.8” (H) x 3”(D)
Operating Temperature
-4°F (-20°C)* to 104°F (40°C)
Video compression
H.264 and MJPEG
Image resolution
1280x720, 640x480, 320x240
Storage Temperature
-40°F (-40°C) to 158°F (70°C)
Wireless interface
802.11 b/g/n, WEP 64/128,
WPA/WPA2
Power Adapter
12V/1.5A, 100~240 VAC,
50/60HZ input, Adapter
designed for indoor use only
IR Lighting
Approx 6’ range at low light
* Onboard heater operates automatically below 43F (6 C). Low temperature operates
to -40 F (-40C) with onboard heater.
© 2016 Ingersoll Rand
Printed in Country.
18-HD74D1-1-EN Rev. 08/16
Open as PDF
Similar pages