Biostar A780L3C AMD Motherboard Setup Manual

A780L3C Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee that
interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the contents
here and specially disclaims any implied warranties of merchantability or fitness
for any purpose. Further the vendor reserves the right to revise this publication
and to make changes to the contents here without obligation to notify any party
beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and we
will not be responsible for any mistakes found in this user’s manual. All the brand
and product names are trademarks of their respective companies.
Dichiarazione di conformità
sintetica
Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives
2004/108/CE, 2006/95/CE and
1999/05/CE
whenever these laws may be applied
Table of Contents
Chapter 1: Introduction.......................................... 3
1.1
1.2
1.3
1.4
1.5
Before You Start ............................................................................ 3
Package Checklist ........................................................................ 3
Motherboard Specifications.......................................................... 4
Rear Panel Connectors ................................................................ 5
Motherboard Layout...................................................................... 6
Chapter 2: Hardware Installation ........................... 7
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Install Central Processing Unit (CPU) ......................................... 7
Install a Heatsink........................................................................... 8
Connect Cooling Fans .................................................................. 9
Installing System Memory .......................................................... 10
Expansion Slots........................................................................... 12
Jumper Setting ............................................................................ 13
Headers & Connectors ............................................................... 14
Chapter 3: BIOS & Software ................................. 18
3.1
3.2
3.3
BIOS Setup.................................................................................. 18
BIOS Update ............................................................................... 18
Software....................................................................................... 23
Chapter 4: Useful Help ......................................... 26
4.1
4.2
4.3
Driver Installation ........................................................................ 26
Troubleshooting........................................................................... 27
RAID Functions ........................................................................... 29
Appendix: Specifications In Other Languages ...... 32
German............................................................................................................ 32
French.............................................................................................................. 34
Italian ............................................................................................................... 36
Spanish ............................................................................................................ 38
Portuguese ...................................................................................................... 40
Polish ............................................................................................................... 42
Russian............................................................................................................ 44
Arabic............................................................................................................... 46
Japanese ......................................................................................................... 48
A780L3C
CHAPTER 1: INTRODUCTION
1.1
Before You Start
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„ Prepare a dry and stable working environment with sufficient
lighting.
„ Always disconnect the computer from power outlet before
operation.
„ Before you take the motherboard out from anti-static bag,
ground yourself properly by touching any safely grounded
appliance, or use grounded wrist strap to remove the static
charge.
„ Avoid touching the components on motherboard or the rear
side of the board unless necessary. Hold the board on the
edge, do not try to bend or flex the board.
„ Do not leave any unfastened small parts inside the case after
installation. Loose parts will cause short circuits which may
damage the equipment.
„ Keep the computer from dangerous area, such as heat
source, humid air and water.
„ The operating temperatures of the computer should be 0 to
45 degrees Celsius.
„ To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit
1.2
Package Checklist
;
;
;
;
Serial ATA Cable x2
Rear I/O Panel for ATX Case x1
Installation Guide x1
Fully Setup Driver DVD x1
Note: The package contents may be different due to the sales region or models in which it was sold.
For more information about the standard package in your region, please contact your dealer or sales
representative.
3
Motherboard Manual
1.3
Motherboard Specifications
SPEC
Socket AM3
AMD 64 Architecture enables 32 and 64 bit computing
CPU
AMD Sempron / Phenom II / Athlon II processors
Supports Hyper Transport 2.0
(Maximum Watt: 95W)
Support Hyper Transport 3.0
FSB
Supports up to 3.2 GT/s Bandwidth
AMD 760G
Chipset
AMD SB710
Low Pin Count Interface
ITE 8728F-BX
Super I/O
Environment Control initiatives
Provides the most commonly used legacy Super
H/W Monitor
I/O functionality
ITE's "Smart Guardian" function
DDR3 DIMM Slots x 2
Dual Channel Mode DDR3 memory module
Main
Max Memory Capacity 16GB
Memory
Each DIMM supports 512MB/1GB/
Supports DDR3 800/1066/1333/1600(OC)
Registered DIMM and ECC DIMM is not supported
2GB/4GB/8GB DDR3
Graphics
Integrated in AMD 760G Chipset
SATA II
Integrated Serial ATA Controller
Max Shared Video Memory is 1024MB
Data transfer rates up to 3 Gb/s
SATA Version 2.0 specification compliant
LAN
Realtek RTL 8105T
Sound
VT1708B
10 / 100 Mb/s auto negotiation
5.1 channels audio out
High Definition Audio
Slots
On Board
Connectors
4
PCI Express X16 slot
x1
Supports PCI-E X16 expansion card
PCI slot
x1
Supports PCI expansion cards
SATA Connector
x4
Each connector supports 1 SATA device
IDE Connector
x1
Each connector supports 2 IDE device
Front Panel Connector
x1
Supports front panel facilities
Front Audio Connector
x1
Supports front panel audio function
CPU Fan Header
x1
CPU Fan power supply (with Smart Fan function)
A780L3C
SPEC
System Fan Header
x1
System Fan Power supply
CMOS Clear Jumper
x1
Restore CMOS data to factory default setting
USB Connector
x2
Each connector supports 2 front panel USB ports
Power Connector (24pin)
x1
Connects to Power supply
Power Connector (4pin)
x1
Connects to Power supply
Printer Port Connector
x1
Each connector supports 1 Printer port
PS/2 Keyboard
x1
Connects to PS/2 Keyboard
PS/2 Mouse
x1
Connects to PS/2 Mouse
Back Panel
VGA port
x1
Connect to D-SUB monitor
I/O
LAN port
x1
Connect to RJ-45 Ethernet cable
USB Port
x4
Connect to USB devices
Audio Jack
x3
Provide Audio-In/Out and microphone connection
Board Size
182 mm(W) x 225 mm(L)
Special
Features
RAID 0 / 1 / 10 support
Biostar reserves the right to add or remove support for any
OS Support
Windows XP / Vista / 7 / 8
OS With or without notice.
1.4
Rear Panel Connectors
5
Motherboard Manual
1.5
Motherboard Layout
Note: ■ represents the 1st pin.
6
A780L3C
CHAPTER 2: HARDWARE INSTALLATION
2.1
Install Central Processing Unit (CPU)
Step 1: Locate the CPU socket on the motherboard
Step 2: Pull the socket locking out from the socket and then raise the lever up to a
90-degree angel.
Step 3: Look for the white triangle on socket, and the gold triangle on CPU should
point towards this white triangle. The CPU will fit only in the correct
orientation.
Note: The CPU fits only in one correct orientation. Do not force the CPU into the socket
to prevent damaging the CPU.
7
Motherboard Manual
Step 4: Hold the CPU down firmly, and then close the lever to locked the position
2.2
Install a Heatsink
Step 1: Place the heatsink and fan assembly onto the retention frame. Match the
heatsink clip with the socket mounting-lug. Hook the spring clip to the
mounting-lug.
Step 2: On the other side, push the retention clip straight down to lock into the
plastic lug on the retention frame, and then press down the locker until it
stops.
Note1: Do not forget to connect the CPU fan connector.
Note2: For proper installation, please kindly refer to the installation manual of your CPU
heatsink.
8
A780L3C
2.3
Connect Cooling Fans
These fan headers support cooling-fans built in the computer. The fan cable and
connector may be different according to the fan manufacturer. Connect the fan
cable to the connector while matching the black wire to pin#1.
CPU_FAN1: CPU Fan Header
Pin
Assignment
1
2
3
Ground
+12V
4
Smart Fan Control
(By Fan)
FAN RPM rate sense
SYS_FAN1: System Fan Header
Pin
1
2
3
Assignment
Ground
+12V
FAN RPM rate sense
Note: CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be connected to pin#2, and the black wire is Ground and should be connected to
GND.
9
Motherboard Manual
2.4
Installing System Memory
A. DDR3 Memory Modules
Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM
on the slot such that the notch on the DIMM matches the break on the slot.
Step 2: Insert the DIMM vertically and firmly into the slot until the retaining chip snap
back in place and the DIMM is properly seated.
Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
10
A780L3C
B. Memory Capacity
DIMM Socket
Location
DDR3 Module
DDR3_A1
512MB/1GB/2GB/4GB/8GB
DDR3_B1
512MB/1GB/2GB/4GB/8GB
Total Memory
Size
Max is 16GB.
C. Dual Channel Memory installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status DDR3_A1 DDR3_B1
Disabled
O
X
Disabled
X
O
Enabled
O
O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or x16)
11
Motherboard Manual
2.5
Expansion Slots
PEX16_1: PCI-Express X16 Slot
-
PCI-Express 2.0 compliant.
Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
PCI1: Peripheral Component Interconnect Slot
This motherboard is equipped with 1 standard PCI slot. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
12
A780L3C
2.6
Jumper Setting
The illustration shows how to set up jumpers. When the jumper cap is placed on
pins, the jumper is “close”, if not, that means the jumper is “open”.
Pin opened
Pin closed
Pin1-2 closed
JCMOS1: Clear CMOS Jumper
Placing the jumper on pin2-3 allows user to restore BIOS safe setting and
CMOS data. Pease carefully follow the procedures to avoid damaging the
motherboard.
1
3
Pin 1-2 Close:
Normal Operation
(default).
1
3
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Load Optimal Defaults and save settings in CMOS.
13
Motherboard Manual
2.7
Headers & Connectors
ATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
ATXPWR2: ATX Power Source Connector
This connector provides +12V to CPU power circuit.
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
Note1: Before you power on the system, please make sure that both ATXPWR1 and
ATXPWR2 connectors have been plugged-in.
Note2: Insufficient power supplied to the system may result in instability or the peripherals
not functioning properly. Use of a PSU with a higher power output is recommended when
configuring a system with more power-consuming devices.
14
A780L3C
PANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
Pin
1
2
3
4
5
6
7
8
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
Assignment
N/A
N/A
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
N/A
N/A
Power LED
Power-on button
SATA1~SATA4: Serial ATA Connectors
These connectors connect to SATA hard disk drives via SATA cables. It satisfies
the SATA 2.0 spec and with transfer rate of 3Gb/s.
Pin
1
2
3
4
5
6
7
Assignment
Ground
TX+
TXGround
RXRX+
Ground
15
Motherboard Manual
IDE1: Hard Disk Connector
The motherboard has a 32-bit Enhanced IDE Controller that provides PIO Mode
0~4, Bus Master, Multi-word DMA, and Ultra DMA 33/66/100/133 functionality.
F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
16
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
NC
Key
A780L3C
F_AUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
J_PRINT1: Printer Port Connector
This header allows you to connector printer on the PC.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
Pin
14
15
16
17
18
19
20
21
22
23
24
25
26
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
17
Motherboard Manual
CHAPTER 3: BIOS & SOFTWARE
3.1
„
„
3.2
BIOS Setup
For better system performance, the BIOS firmware is being continuously
updated. The BIOS information described below in this manual is for your
reference only and the actual BIOS information and settings on board may
be different from this manual
For further information of setting up the BIOS, please refer to the BIOS
Manual in the Setup DVD.
BIOS Update
There are three ways to update the BIOS:
BIOS Update Utility, BIOS Online Update Utility and BIOS Flasher.
1. BIOS Update Utility
1. Installing BIOS Update Utility from the DVD Driver.
2. Download the proper BIOS from www.biostar.com.tw .
AWARD BIOS
Show current BIOS information
Clear CMOS function
(Only for AWARD BIOS)
Save current BIOS
to a .bin file
Update BIOS
with a BIOS file
18
AMI BIOS
A780L3C
<Backup BIOS>
Once click on this button, the saving
dialog will show. Choose the position to
save file and enter file name. (We
recommend that the file name should be
English/number and no longer than 7
characters.) Then click Save.
After the saving process, finish dialog
will show. Click on OK to complete the
BIOS Backup procedure.
<Update BIOS>
Before doing this, please download the proper BIOS file from the website.
For AWARD BIOS, update BIOS
procedure should be run with Clear
CMOS function, so please check on
Clear CMOS first.
Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.
After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.
19
Motherboard Manual
The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.
After the BIOS Update process, click on
OK to restart the system.
While the system boots up and the full screen logo shows, press
key to enter BIOS setup.
<Delete>
In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.
2. Online Update Utility
1. Installing BIOS Update Utility from the DVD Driver.
2. Please make sure the system is connected to the internet before using this
function.
3. Open BIOS Update Utility and
click the Online Update button
on the main screen.
4. An open dialog will show up to
request your agreement to
start the BIOS update. Click
Yes to start the online update
procedure.
20
A780L3C
5. If there is a new BIOS version,
the utility will ask you to
download it. Click Yes to
proceed.
6. After the download is
completed, you will be asked
to program (update) the BIOS
or not. Click Yes to proceed.
7. After the updating process is
finished, you will be asked you
to reboot the system. Click
OK to reboot.
8. While the system boots up and the full screen logo shows up, press
<Delete> key to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.
21
Motherboard Manual
3. BIOSTAR BIOS Flasher
BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and
simple way to update your BIOS via USB pen drive.
Note1: This utility only allows storage device with FAT32/16 format and single partition.
Note2: Shutting down or resetting the system while updating the BIOS will lead to system
boot failure.
The BIOSTAR BIOS Flasher is built in the BIOS ROM. To enter the utility, press
<F12> during the Power-On Self Tests (POST) procedure while booting up.
Updating BIOS with BIOSTAR BIOS Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, save the BIOS file into a USB pen
drive or a floppy disk.
3. Insert the USB pen drive or the floppy disk
that contains the BIOS file to the USB port
or the floppy disk drive.
4. Power on or reset the computer and then
press <F12> during the POST process. A
select dialog as the picture on the right
appears. Select the device contains the
BIOS file and press <Enter> to enter the
utility.
5. The utility will show the BIOS files and their respective information. Select
the proper BIOS file and press <Enter> then <Y> to perform the BIOS
update process.
6. After the update process,
the utility will ask you to
reboot the system.
Press <Y> to proceed.
BIOS update completes.
22
A780L3C
3.3
Software
Installing Software
1.
Insert the Setup CD to the optical drive. The drivers installation program would
appear if the Autorun function has been enabled.
2.
Select Software Installation, and then click on the respective software title.
3. Follow the on-screen instructions to complete the installation.
Note1: All the information and content about following software are subject to be changed without
notice. For better performance, the software is being continuously updated.
Note2: The information and pictures described below are for your reference only. The actual
information and settings on board may be slightly different from this manual.
Launching Software
After the installation process, you will see the software icon “eHOT Line” / “BIOS
Update” appears on the desktop. Double-click the icon to launch the utility.
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our Tech-Support system.
This utility will collect the system information which is useful for analyzing the problem
you may have encountered, and then send these information to our tech-support
department to help you fix the problem.
Note: Before you use this utility, please set Outlook Express as your default e-mail client application program.
represents i mportant
information that you
must provide. Without
this information, you may
not be able to send out
the mail .
*
This block wi ll show
the information which
would be collected in
the mail.
condition
* Describe
of your system.
your area or
* Select
the area close to you.
Provide the e-mail
address that you woul d
like to send the copy to.
the name of
* Provide
the memory module
manufacturer.
Provide the name of
the power supply
manufacturer and the
model no.
Send the mail out.
Exit this dialog.
Save these information to a .txt fi le
23
Motherboard Manual
After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.
If you want to save this information to a .txt file, click “Save As…” and then you will see
a saving dialog appears asking you to enter file name.
Enter the file name and then click “Save”.
Your system information will be saved to
a .txt file.
Open the saved .txt file, you will see your
system information including
motherboard/BIOS/CPU/video/
device/OS information. This information
is also concluded in the sent mail.
Note1: We will not share customer’s data with any other third parties, so please feel free to
provide your system information while using eHot-Line service.
Note2: If you are not using Outlook Express as your default e-mail client application, you may
need to save the system information to a .txt file and send the file to our tech support with other
e-mail application. Go to the following web http://www.biostar.com.tw/app/en/about/contact.php for
getting our contact information.
24
A780L3C
BIOScreen Utility (Optional)
This utility allows you to personalize your boot logo easily. You can choose
BMP as your boot logo so as to customize your computer.
Please follow the following instructions to update boot logo:
1. Load Image:Choose the picture as the boot logo.
2. Transform:Transform the picture for BIOS and preview the result.
3. Update Bios:Write the picture to BIOS Memory to complete the update.
25
Motherboard Manual
CHAPTER 4: USEFUL HELP
4.1
Driver Installation
After you installed your operating system, please insert the Fully Setup Driver
DVD into your optical drive and install the driver for better system performance.
You will see the following window after you insert the DVD
The setup guide will auto detect your motherboard and operating system.
Note: If this window didn’t show up after you insert the Driver DVD, please use file browser
to locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will list the
compatible driver for your motherboard and operating system. Click on each
device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide will list
the software available for your system, click on each software title to launch the
installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver DVD.
Click on the Manual icon to browse for available manual.
Note: You will need Acrobat Reader to open the manual file. Please download the latest
version of Acrobat Reader software from http://get.adobe.com/reader/
26
A780L3C
4.2
Troubleshooting
Probable
1.
There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work
2.
Indicator light on keyboard does
not shine.
System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.
System does not boot from a hard disk
drive, but can be booted from optical
drive.
Solution
1.
2.
3.
Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
1.
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from an optical
1.
Back up data and applications
drive. Hard disks can be read,
files.
applications can be used, but system 2.
Reformat the hard drive.
fails to boot from a hard disk.
Re-install applications and data
using backup disks.
Screen message shows “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
System cannot boot after user installs a 1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
27
Motherboard Manual
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
28
A780L3C
4.3
RAID Functions
Operating System
z
Supports Windows XP, Windows Vista, and Windows 7.
Raid Arrays
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write
times for many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.
How RAID Works
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It
breaks up a large file into smaller blocks and performs disk reads and writes
across multiple drives in parallel. The size of each block is determined by the
stripe size parameter, which you set during the creation of the RAID set based
on the system environment. This technique reduces overall disk access time
and offers high bandwidth.
Features and Benefits
-
Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the
platform.
Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
Benefits: provides increased data throughput, especially for large files.
No capcity loss penalty for parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
Fault Tolerance: No.
Total Capacity: (Minimal. HDD Capacity) x (Connected HDDs Amount)
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
29
Motherboard Manual
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a
RAID 1 array system. The mirrored (backup) copy of the data can reside on the
same disk or on a second redundant drive in the array. RAID 1 provides a
hot-standby copy of data if the active volume or drive is corrupted or becomes
unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive
and less reliable media.
Features and Benefits
-
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
Fault Tolerance: Yes.
Block 1
Block 2
Block 3
30
Block 1
Block 2
Block 3
A780L3C
RAID 10:
RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10
solution for improved resiliency, performance and rebuild performance.
Features and Benefits
-
-
Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID
levels in an array, and allows for spare disks.
Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
Fault Tolerance: Yes.
Block 1
Block 3
Block 5
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Block 2
Block 4
Block 6
31
Motherboard Manual
APPENDIX: Specifications In Other Languages
German
Spezifikationen
CPU
Sockel AM3
Die AMD 64-Architektur unterstützt eine 32-Bit- und
AMD Sempron / Phenom II / Athlon II
64-Bit-Datenverarbeitung
Prozessoren (Maximales Watt: 95W)
Unterstützt Hyper Transport 2.0
Unterstützt Hyper Transport 3.0 mit einer
FSB
Bandbreite von bis zu 3.2 GT/s
AMD 760G
Chipsatz
AMD SB710
Low Pin Count-Schnittstelle
ITE8728F-BX
Umgebungskontrolle,
Super E/A
Bietet die häufig verwendeten alten Super
Hardware-Überwachung
E/A-Funktionen.
"Smart Guardian"-Funktion von ITE
DDR3 DIMM-Steckplätze x 2
Dual-Kanal DDR3 Speichermodul
Arbeitsspeiche Max. 16GB Arbeitsspeicher
r
Unterstützt DDR3 800/1066/1333/1600(OC)
Jeder DIMM unterstützt 512MB/1GB/
registrierte DIMMs. ECC DIMMs werden nicht unterstützt.
2GB/4GB/8GB DDR3.
Grafik
Integrierter AMD 760G-Chipsatz
SATA
Integrierter Serial ATA-Controller
Max. 1024MB gemeinsam benutzter Videospeicher
Datentransferrate bis zu 3 Gb/s
Konform mit der SATA-Spezifikation Version 2.0.
LAN
Realtek RTL 8105T
10 / 100 Mb/s Auto-Negotiation
HD
5.1-Kanal-Audioausgabe
Audio-Unterstü VT1708B
Unterstützt High-Definition Audio
tzung
Steckplätze
PCI Express X16 Steckplatz
x1
PCI-Steckplatz
x1
Onboard-Ansc SATA-Anschluss
x4
Jeder Anschluss unterstützt 1 SATA-Laufwerk
hluss
IDE-Anschluss
x1
Jeder Anschluss unterstützt 2 IDE-Laufwerke
Fronttafelanschluss
x1
Unterstützt die Fronttafelfunktionen
32
A780L3C
Spezifikationen
Front-Audioanschluss
x1
CPU-Lüfter-Sockel
x1
Unterstützt die Fronttafel-Audioanschlussfunktion
CPU-Lüfterstromversorgungsanschluss (mit Smart
Fan-Funktion)
System-Lüfter-Sockel
x1
"CMOS löschen"-Sockel
x1
USB-Anschluss
x2
Stromanschluss (24-polig)
x1
Stromanschluss (4-polig)
x1
Druckeranschluss Anschluss
x1
PS/2-Tastatur
x1
PS/2-Maus
x1
Rückseiten-E/
VGA-Anschluss
x1
A
LAN-Anschluss
x1
USB-Anschluss
x4
Audioanschluss
x3
Platinengröße
System-Lüfter-Stromversorgungsanschluss
Jeder Anschluss unterstützt 2 Fronttafel-USB-Anschlüsse
Jeder Anschluss unterstützt 1 Druckeranschluss
182 mm (B) X 225 mm (L)
Sonderfunktion
en
Unterstützt RAID 0 / 1 / 10
Biostar behält sich das Recht vor, ohne Ankündigung die
OS-Unterstütz
ung
Windows XP / Vista / 7 / 8
Unterstützung für ein Betriebssystem hinzuzufügen oder zu
entfernen.
33
Motherboard Manual
French
SPEC
Socket AM3
UC
L'architecture AMD 64 permet le calcul 32 et 64 bits
Processeurs AMD Sempron / Phenom II /
Prend en charge Hyper Transport 2.0
Athlon II (Watt maximum : 95W)
Bus frontal
Prend en charge Hyper Transport 3.0 jusqu'à
une bande passante de 3.2 GT/s
Chipset
AMD 760G
AMD SB710
Interface à faible compte de broches
ITE 8728F-BX
Super E/S
Initiatives de contrôle environnementales,
Fournit la fonctionnalité de Super E/S
Moniteur de matériel
patrimoniales la plus utilisée.
Fonction "Gardien intelligent" de l'ITE
Fentes DDR3 DIMM x 2
Module de mémoire DDR3 à mode à double voie
Mémoire
Capacité mémoire maximale de 16Go
Prend en charge la DDR3 800/1066/1333/1600(OC)
principale
Chaque DIMM prend en charge des DDR3 de
Les DIMM à registres et DIMM avec code correcteurs
512Mo/1Go/2Go/4Go/8Go
d'erreurs ne sont pas prises en charge
Graphiques
Integré dans la chipset AMD 760G
Mémoire vidéo partagée maximale de 1024 Mo
SATA
Contrôleur Serial ATA intégré
Taux de transfert jusqu'à 3 Go/s.
Conforme à la spécification SATA Version 2.0
LAN
Realtek RTL 8105T
10 / 100 Mb/s négociation automatique
Prise en
Sortie audio à 5.1 voies
charge audio VT1708B
Prise en charge de l'audio haute définition
HD
Fentes
Connecteur
embarqué
Fente PCI Express X16
x1
Fente PCI
x1
Connecteur SATA
x4
Chaque connecteur prend en charge 1 périphérique SATA
Connecteur IDE
x1
Chaque connecteur prend en charge 2 périphériques IDE
Connecteur du panneau avant
x1
Prend en charge les équipements du panneau avant
Connecteur Audio du panneau avant x1
34
Prend en charge la fonction audio du panneau avant
A780L3C
SPEC
Alimentation électrique du ventilateur UC (avec fonction de
Embase de ventilateur UC
x1
ventilateur intelligent)
Embase de ventilateur système
x1
Embase d'effacement CMOS
x1
Connecteur USB
x2
Alimentation électrique du ventilateur système
Chaque connecteur prend en charge 2 ports USB de panneau
avant
Connecteur d'alimentation
x1
(24 broches)
Connecteur d'alimentation
x1
(4 broches)
E/S du
panneau
arrière
Dimensions
de la carte
Fonctionnalit
és spéciales
Support SE
Connecteur de Port d'imprimante
x1
Clavier PS/2
x1
Souris PS/2
x1
Port VGA
x1
Port LAN
x1
Port USB
x4
Fiche audio
x3
Chaque connector prend en charge 1 Port d'imprimante
182 mm (l) X 225 mm (H)
Prise en charge RAID 0 / 1 / 10
Biostar se réserve le droit d'ajouter ou de supprimer le support
Windows XP / Vista / 7 / 8
de SE avec ou sans préavis.
35
Motherboard Manual
Italian
SPECIFICA
CPU
Socket AM3
L’architettura AMD 64 abilita la computazione 32 e 64
Processori AMD Sempron / Phenom II /
bit
Athlon II (Watt massimo: 95W)
Supporto di Hyper Transport 2.0
Supporto di HyperTransport 3.0 fino a 3.2
FSB
GT/s di larghezza di banda
AMD 760G
Chipset
AMD SB710
Interfaccia LPC (Low Pin Count)
ITE 8728F-BX
Funzioni di controllo dell’ambiente:
Super I/O
Fornisce le funzionalità legacy Super I/O
Monitoraggio hardware
usate più comunemente.
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR3 x 2
Modulo di memoria DDR3 a canale doppio
Memoria
Capacità massima della memoria 16GB
principale
Ciascun DIMM supporta DDR3
Supporto di DDR3 800/1066/1333/1600(OC)
DIMM registrati e DIMM ECC non sono supportati
512MB/1GB/2GB/4GB/8GB
Grafica
Integrata nel Chipset AMD 760G
SATA
Controller Serial ATA integrato
La memoria video condivisa massima è di 1024 MB
Velocità di trasferimento dei dati fino a 3 Gb/s.
Compatibile specifiche SATA Versione 2.0.
LAN
Realtek RTL 8105T
Negoziazione automatica 10 / 100 Mb/s
Uscita audio 5.1 canali
Supporto
audio HD
Alloggi
Connettori
su scheda
36
VT1708B
Supporto audio High-Definition (HD)
Alloggio PCI Express X16
x1
Alloggio PCI
x1
Connettore SATA
x4
Ciascun connettore supporta 1 unità SATA
Connettore IDE
x1
Ciascun connettore supporta 2 unità IDE
Connettore pannello frontale
x1
Supporta i servizi del pannello frontale
Connettore audio frontale
x1
Supporta la funzione audio pannello frontale
Collettore ventolina CPU
x1
Alimentazione ventolina CPU (con funzione Smart Fan)
A780L3C
SPECIFICA
Collettore ventolina sistema
x1
Collettore cancellazione CMOS
x1
Connettore USB
x2
Alimentazione ventolina di sistema
Ciascun connettore supporta 2 porte USB pannello
frontale
Connettore alimentazione
x1
(24 pin)
Connettore alimentazione
x1
(4 pin)
Connettore Porta stampante
x1
Tastiera PS/2
x1
Mouse PS/2
x1
I/O pannello Porta VGA
x1
posteriore
Porta LAN
x1
Porta USB
x4
Connettore audio
x3
Ciascun connettore supporta 1 Porta stampante
Dimensioni
scheda
182 mm (larghezza) x 225 mm (altezza)
Caratteristic
he speciali
Supporto RAID 0 / 1 / 10
Biostar si riserva il diritto di aggiungere o rimuovere il
Sistemi
operativi
supportati
Windows XP / Vista / 7 / 8
supporto di qualsiasi sistema operativo senza
preavviso.
37
Motherboard Manual
Spanish
Especificación
Conector AM3
La arquitectura AMD 64 permite el procesado de 32 y 64 bits
CPU
Procesadores AMD Sempron / Phenom II /
Soporta las tecnologías Hyper Transport 2.0
Athlon II (Vatio máximo: 95W)
Admite HyperTransport 3.0 con un ancho de
FSB
banda de hasta 3.2 GT/s
Conjunto de AMD 760G
chips
AMD SB710
Interfaz de cuenta Low Pin
ITE 8728F-BX
Iniciativas de control de entorno,
Súper E/S
Le ofrece las funcionalidades heredadas de uso
Monitor hardware
más común Súper E/S.
Función "Guardia inteligente" de ITE
Ranuras DIMM DDR3 x 2
Módulo de memoria DDR3 de canal Doble
Memoria
Capacidad máxima de memoria de 16GB
principal
Cada DIMM admite DDR de
Admite DDR3 de 800/1066/1333/1600(OC)
No admite DIMM registrados o DIMM compatibles con ECC
512MB/1GB/2GB/4GB/8GB
Gráficos
Integrados en el conjunto de chips AMD 760G
SATA
Controlador ATA Serie Integrado
Memoria máxima de vídeo compartida de 1024 MB
Tasas de transferencia de hasta 3 Gb/s.
Compatible con la versión SATA 2.0.
Red Local
Realtek RTL 8105T
Negociación de 10 / 100 Mb/s
Salida de sonido de 5.1 canales
Soporte de
sonido HD
Ranuras
Conectores
en placa
38
VT1708B
Soporte de sonido Alta Definición
Ranura PCI Express X16
X1
Ranura PCI
X1
Conector SATA
X4
Cada conector soporta 1 dispositivos SATA
Conector IDE
X1
Cada conector soporta 2 dispositivos IDE
Conector de panel frontal
X1
Soporta instalaciones en el panel frontal
Conector de sonido frontal
X1
Soporta funciones de sonido en el panel frontal
A780L3C
Especificación
Cabecera de ventilador de CPU
X1
Fuente de alimentación de ventilador de CPU (con función
Smart Fan)
Cabecera de ventilador de sistema
X1
Cabecera de borrado de CMOS
X1
Conector USB
X2
Conector de alimentación
X1
Fuente de alimentación de ventilador de sistema
Cada conector soporta 2 puertos USB frontales
(24 patillas)
Conector de alimentación
X1
(4 patillas)
Conector Puerto de impresora
X1
Teclado PS/2
X1
Ratón PS/2
X1
Panel trasero Puerto VGA
X1
de E/S
Puerto de red local
X1
Puerto USB
X4
Conector de sonido
X3
Cada conector soporta 1 Puerto de impresora
Tamaño de
la placa
182 mm. (A) X 225 Mm. (H)
Funciones
especiales
Admite RAID 0 / 1 / 10
Soporte de
sistema
operativo
Biostar se reserva el derecho de añadir o retirar el soporte de
Windows XP / Vista / 7 / 8
cualquier SO con o sin aviso previo.
39
Motherboard Manual
Portuguese
ESPECIFICAÇÕES
CPU
FSB
Socket AM3
A arquitectura AMD 64 permite uma computação de 32 e 64
Processadores AMD Sempron / Phenom II /
bits
Athlon II (Watt máximo: 95W)
Suporta as tecnologias Hyper Transport 2.0
Suporta a tecnologia HyperTransport 2.0 com
uma largura de banda até 3.2 GT/s
Chipset
AMD 760G
AMD SB710
Interface LPC (Low Pin Count).
ITE 8728F-BX
Especificaçã
o Super I/O
Iniciativas para controlo do ambiente
Proporciona as funcionalidades mais utilizadas
Monitorização do hardware
em termos da especificação Super I/O.
Função "Smart Guardian" da ITE
Ranhuras DIMM DDR3 x 2
Módulo de memória DDR3 de canal duplo
Capacidade máxima de memória: 16GB
Memória
principal
Suporta módulos DDR3 800/1066/1333/1600(OC)
Cada módulo DIMM suporta uma memória
Os módulos DIMM registados e os DIMM ECC não são
DDR3 de 512MB/1GB/
suportados
2GB/4GB/8GB
Placa gráfica Integrada no chipset AMD 760G
SATA
Memória de vídeo máxima partilhada: 1024 MB
Velocidades de transmissão de dados até 3 Gb/s.
Controlador Serial ATA integrado
Compatibilidade com a especificação SATA versão 2.0.
LAN
Realtek RTL 8105T
Auto negociação de 10 / 100 Mb/s
Suporte para
Saída de áudio de 5.1 canais
áudio de alta VT1708B
Suporta a especificação High-Definition Audio
definição
Ranhuras
Conectores
na placa
40
Ranhura PCI Express X16
x1
Ranhura PCI
x1
Conector SATA
x4
Cada conector suporta 1 dispositivo SATA
Conector IDE
x1
Cada conector suporta 2 dispositivos IDE
Conector do painel frontal
x1
Para suporte de várias funções no painel frontal
Conector de áudio frontal
x1
Suporta a função de áudio no painel frontal
A780L3C
ESPECIFICAÇÕES
Conector da ventoinha da CPU
x1
Alimentação da ventoinha da CPU (com a função Smart Fan)
Conector da ventoinha do sistema
x1
Alimentação da ventoinha do sistema
Conector para limpeza do CMOS
x1
Conector USB
x2
Conector de alimentação
x1
Cada conector suporta 2 portas USB no painel frontal
(24 pinos)
Conector de alimentação
x1
(4 pinos)
Entradas/Saí
das no painel
traseiro
Tamanho da
placa
Característic
as especiais
Conector da para impressora
x1
Teclado PS/2
x1
Rato PS/2
x1
Porta VGA
x1
Porta LAN
x1
Porta USB
x4
Tomada de áudio
x3
182 mm (L) X 225 mm (A)
Suporta as funções RAID 0 / 1 / 10
Sistemas
operativos
suportados
Cada conector suporta 1 Porta para impressora
A Biostar reserva-se o direito de adicionar ou remover suporte
Windows XP / Vista / 7 / 8
para qualquer sistema operativo com ou sem aviso prévio.
41
Motherboard Manual
Polish
SPEC
Socket AM3
Architektura AMD 64 umożliwia przetwarzanie 32 i 64 bitowe
Procesor
AMD Sempron / Phenom II / Athlon II Procesory
Obsługa Hyper Transport 2.0
(Maksymalny Watt: 95W)
Obsługa HyperTransport 3.0 o szerokości
FSB
pasma do 3.2 GT/s
AMD 760G
Chipset
AMD SB710
Gniazda DDR3 DIMM x 2
Moduł pamięci DDR3 z trybem podwójnego kanału
Pamięć
Maks. wielkość pamięci 16GB
główna
Każde gniazdo DIMM obsługuje moduły
Obsługa DDR3 800/1066/1333/1600(OC)
Brak obsługi Registered DIMM oraz ECC DIMM
512MB/1GB/2GB/4GB/8GB DDR3
Interfejs Low Pin Count
ITE 8728F-BX
Super I/O
Funkcje kontroli warunków pracy,
Zapewnia najbardziej powszechne funkcje
Monitor H/W
Super I/O.
Funkcja ITE "Smart Guardian"
Grafika
Zintegrowana w chipsecie AMD 760G
SATA
Zintegrowany kontroler Serial ATA
Maks. wielkość współdzielonej pamięci video wynosi 1024 MB
Transfer danych do 3 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2.0.
LAN
Realtek RTL 8105T
10 / 100 Mb/s z automatyczną negocjacją szybkości
5.1 kanałowe wyjście audio
Obsługa
audio HD
Gniazda
Złącza
wbudowane
VT1708B
Obsługa High-Definition Audio
Gniazdo PCI Express X16
x1
Gniazdo PCI
x1
Złącze SATA
x4
Każde złącze obsługuje 1 urządzenie SATA
Złącze IDE
x1
Każde złącze obsługuje 2 urządzenia IDE
Złącze panela przedniego
x1
Obsługa elementów panela przedniego
Przednie złącze audio
x1
Obsługa funkcji audio na panelu przednim
Złącze główkowe wentylatora procesora x1
42
Zasilanie wentylatora procesora (z funkcją Smart Fan)
A780L3C
SPEC
Złącze główkowe wentylatora systemowego x1 Zasilanie wentylatora systemowego
Złącze główkowe kasowania CMOS
x1
Złącze USB
x2
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Złącze Port drukarki
x1
Klawiatura PS/2
x1
Mysz PS/2
x1
Back Panel
Port VGA
x1
I/O
Port LAN
x1
Port USB
x4
Gniazdo audio
x3
Każde złącze obsługuje 2 porty USB na panelu przednim
Każde złącze obsługuje 1 Port drukarki
Wymiary
płyty
182 mm (S) X 225 mm (W)
Funkcje
specjalne
Obsługa RAID 0 / 1 / 10
Obsluga
systemu
operacyjneg
o
Biostar zastrzega sobie prawo dodawania lub odwoływania
Windows XP / Vista / 7 / 8
obsługi dowolnego systemu operacyjnego bez
powiadomienia.
43
Motherboard Manual
Russian
СПЕЦ
CPU
(центральн
ый
процессор)
FSB
Гнездо AM3
Архитектура AMD 64 разрешать обработка данных на 32 и
Процессоры AMD Sempron / Phenom II /
64 бит
Athlon II (Максимальный ватт: 95W)
Поддержка Hyper Transport 2.0
Поддержка HyperTransport 3.0 с пропускной
способностью до 3.2 GT/s
Набор
AMD 760G
микросхем
AMD SB710
Слоты DDR3 DIMM x 2
Модуль памяти с двухканальным режимом DDR3
Основная
Максимальная ёмкость памяти 16ГБ
Поддержка DDR3 800/1066/1333/1600(OC)
память
Каждый модуль DIMM поддерживает
Не поддерживает зарегистрированные модули DIMM and
Super I/O
Графика
SATA
Локальная
сеть
512МБ/1ГБ/2ГБ/4ГБ/8ГБ DDR3
ECC DIMM
ITE 8728F-BX
Интерфейс с низким количеством выводов
Обеспечивает наиболее используемые
Инициативы по охране окружающей среды,
действующие функциональные
Аппаратный монитор
возможности Super I/O.
Функция ITE "Smart Guardian" (Интеллектуальная защита)
Встроенная в набор микросхем AMD 760G
Максимальная совместно используемая видео память
составляет 1024 МБ
Встроенное последовательное устройство
скорость передачи данных до 3 гигабит/с.
управления ATA
Соответствие спецификации SATA версия 2.0.
Realtek RTL 8105T
Автоматическое согласование 10 / 100 Мб/с
Звуковая
поддержка
жесткого
Звуковая поддержка High-Definition
VT1708B
5.1канальный звуковой выход
диска
Слоты
Слот PCI Express X16
x1
Слот PCI
x1
Встроенный Разъём SATA
x4
разъём
44
Каждый разъём поддерживает 1 устройство SATA
Каждый разъём поддерживает 2 встроенных интерфейса
Разъём IDE
x1
Разъём на лицевой панели
x1
Поддержка устройств на лицевой панели
Входной звуковой разъём
x1
Поддержка звуковых функций на лицевой панели
накопителей
A780L3C
СПЕЦ
Контактирующее приспособление
Источник питания для вентилятора центрального
вентилятора центрального
процессора
x1
Контактирующее приспособление
вентилятора системы
x1
процессора (с функцией интеллектуального вентилятора)
Источник питания для вентилятора системы
Открытое контактирующее
приспособление CMOS
x1
USB-разъём
x2
Разъем питания (24 вывод)
x1
Разъем питания (4 вывод)
x1
Разъём Порт подключения
Каждый разъём поддерживает 1 Порт подключения
принтера
x1
Клавиатура PS/2
x1
Мышь PS/2
x1
панель
Порт VGA
x1
средств
Задняя
Порт LAN
x1
ввода-выво USB-порт
да
Гнездо для подключения
x4
наушников
x3
Размер
панели
Каждый разъём поддерживает 2 USB-порта на лицевой
панели
принтера
182 мм (Ш) X 225 мм (В)
Специальн
ые
технические Поддержка RAID 0 / 1 / 10
характерист
ики
Biostar сохраняет за собой право добавлять или удалять
Поддержка
OS
Windows XP / Vista / 7 / 8
средства обеспечения для OS с или без
предварительного уведомления.
45
‫‪Motherboard Manual‬‬
‫‪Arabic‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪AM3‬ﻡﻘﺒﺲ‬
‫إﺟﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺑﻴﺔ ﺑﺴﺮﻋﺔ ‪ 32‬و‪ 64‬ﺑﺖ‪AMD 64‬ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ‬
‫وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫اﻟﻤﺮآﺰیﺔ‬
‫‪AMD Sempron / Phenom II / Athlon II‬ﻡﻌﺎﻟﺠﺎت‬
‫و ‪Hyper Transport2.0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫)و‪: 95‬ﻗﺼﻮى واط(‬
‫اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ اﻟﺠﺎﻥﺒﻲ‬
‫‪ 3.2 GT/s‬ﺑﺘﺮدد یﺼﻞ إﻟﻰ‪HyperTransport 3.0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪AMD 760G‬‬
‫ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫‪AMD SB710‬‬
‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪ITE 8728F-BX‬‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻡﺎً‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬
‫ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺡﺎﻟﺔ اﻷﺟﻬﺰة‬
‫‪Super I/O‬‬
‫‪ ITE‬ﻡﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫ﻓﺘﺤﺔ ‪DDR3 DIMM‬‬
‫ﻋﺪد‪2‬‬
‫ﻡﺰدوﺟﺔ اﻟﻘﻨﺎة‪DDR3‬وﺡﺪة ذاآﺮة‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 16‬ﺟﻴﺠﺎ ﺑﺎیﺖ‬
‫ﺳﻌﺎت ‪DDR3 (OC)1600/1333/1066/800‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع‬
‫ﻡﻴﺠﺎ ﺑﺎیﺖ ‪ /512‬ﺳﻌﺔ ‪ DDR3‬ﺗﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫ﻡﻴﺠﺎ ﺑﺎیﺖ‬
‫و‪ /1‬و‪ /2‬و‪ /4‬و‪ 8‬ﺟﻴﺠﺎ ﺑﺎیﺖ‬
‫‪ ECC‬وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻡﻊ ‪DIMM‬ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت‬
‫‪ AMD 760G‬ﻡﺪﻡﺠﺔ ﻓﻲ رﻗﺎﺋﻖ‬
‫أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪیﻮ اﻟﻤﺸﺘﺮآﺔ ‪ 1024‬ﻡﻴﺠﺎ ﺑﺎیﺖ‬
‫‪SATA‬‬
‫ﻡﺘﻜﺎﻡﻞ‪Serial ATA‬ﻡﺘﺤﻜﻢ‬
‫ﺵﺒﻜﺔ داﺥﻠﻴﺔ‬
‫‪Realtek RTL 8105T‬‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫ﺟﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪3.‬ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ‬
‫‪ 2.0.‬اﻹﺹﺪار ‪SATA‬ﻡﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬
‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻡﻴﺠﺎ ﺑﺎیﺖ ‪ /‬ﺙﺎﻥﻴﺔ‬
‫ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‪5.1‬‬
‫دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ‬
‫اﻟﺘﻌﺮیﻒ‬
‫اﻟﻔﺘﺤﺎت‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫اﻟﻠﻮﺡﺔ‬
‫‪VT1708B‬‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻡﻦ‬
‫ﻓﺘﺤﺔ ‪PCI Express x16‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد‪1‬‬
‫ﻡﻨﻔﺬ ‪SATA‬‬
‫ﻋﺪد‪4‬‬
‫‪SATA‬یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺡﺪ ﻡﻦ أﺟﻬﺰة‬
‫ﻡﻨﻔﺬ ‪IDE‬‬
‫ﻋﺪد ‪1‬‬
‫‪IDE‬یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺟﻬﺰة‬
‫ﻡﻨﻔﺬ اﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‬
‫‪46‬‬
‫‪A780L3C‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫وﺹﻠﺔ ﻡﺮوﺡﺔ وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ‬
‫ﻋﺪد ‪1‬‬
‫‪Smart Fan‬ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺡﺔ وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔ‬
‫وﺹﻠﺔ ﻡﺮوﺡﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪1‬‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺡﺔ اﻟﻨﻈﺎم‬
‫وﺹﻠﺔ ﻡﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ‪USB‬‬
‫ﻋﺪد ‪2‬‬
‫ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺡﺔ ﻡﻔﺎﺗﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﺎﻓﺬ دﺥﻞ‪/‬ﺥﺮج‬
‫ﻡﻨﻔﺬ ‪VGA‬‬
‫ﻋﺪد ‪1‬‬
‫اﻟﻠﻮﺡﺔ اﻟﺨﻠﻔﻴﺔ‬
‫ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻡﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﺎﻓﺬ ‪USB‬‬
‫ﻋﺪد‪4‬‬
‫ﻡﻘﺒﺲ ﺹﻮت‬
‫ﻋﺪ‪3‬‬
‫ﺡﺠﻢ اﻟﻠﻮﺡﺔ‬
‫‪ 182‬ﻡﻢ )ﻋﺮض( ‪ 225 X‬ﻡﻢ )ارﺗﻔﺎع(‬
‫ﻡﺰایﺎ ﺥﺎﺹﺔ‬
‫‪RAID 0 / 1 / 10‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫‪Windows XP / Vista / 7 / 8‬‬
‫ﺑﺎﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‪USB‬یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ‬
‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أو ‪Biostar‬ﺗﺤﺘﻔﻆ‬
‫ﺑﺪون إﺥﻄﺎر‪.‬‬
‫‪47‬‬
Motherboard Manual
Japanese
仕様
AMD 64アーキテクチャでは、
32ビットと64ビット計算が可能
Socket AM3
CPU
です
AMD Sempron / Phenom II / Athlon II プロセッ
ハイパートランスポート2.0とクールアンドクワイアットをサ
サ (最高のワット: 95W)
ポートします
3.2 GT/sのバンド幅までハイパートランスポー
FSB
ト3.0をサポートします
チップセッ
AMD 760G
ト
AMD SB710
DDR3 DIMMスロット x 2
デュアル チャンネルモードDDR3メモリモジュール
メインメモ
最大メモリ容量16GB
リ
各DIMMは 512MB/1GB/2GB/4GB/8GB DDR3
DDR3 800/1066/1333/1600(OC) をサポート
登録済みDIMMとECC DIMMはサポートされません
をサポート
低ピンカウントインターフェイス
ITE 8728F-BX
Super I/O
環境コントロールイニシアチブ、
もっとも一般に使用されるレガシーSuper I/O
H/Wモニター
機能を採用しています。
ITEの「スマートガーディアン」機能
グラフィッ
クス
AMD 760Gチップセットに統合
最大の共有ビデオメモリは1024MBです
最高3Gb/秒のデータ転送速度
SATA
統合シリアルATAコントローラ
SATAバージョン2.0仕様に準拠。
LAN
Realtek RTL 8105T
10 / 100 Mb/秒のオートネゴシエーション
HDオーディ
オのサポー
5.1チャンネルオーディオアウト
VT1708B
ハイデフィニションオーディオのサポート
ト
PCI Express X16スロット
x1
PCIスロット
x1
SATAコネクタ
x4
各コネクタは1つのSATAデバイスをサポートします
IDEコネクタ
x1
各コネクタは2つのIDEデバイスをサポートします
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
スロット
オンボード
コネクタ
48
A780L3C
仕様
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x1
システムファン電源装置
CMOSクリアヘッダ
x1
USBコネクタ
x2
各コネクタは2つのフロントパネルUSBポートをサポートし
ます
電源コネクタ(24ピン)
x1
電源コネクタ(4ピン)
x1
プリンタポートコネクタ
x1
PS/2キーボード
x1
PS/2マウス
x1
背面パネル
VGAポート
x1
I/O
LANポート
x1
USBポート
x4
オーディオジャック
x3
各コネクタは1つのプリンタポートをサポートします
ボードサイ
ズ
特殊機能
182 mm (幅) X 225 mm (高さ)
RAID 0 / 1 / 10 のサポート
Biostarは事前のサポートなしにOSサポートを追加または削
OSサポート Windows XP / Vista / 7 / 8
除する権利を留保します。
2012/07/20
49
Open as PDF
Similar pages