Digital Video Recorder
User Manual (V2.2.4)
UD.6L0202B0068A02
User Manual of DS-7100HWI/HVI-SL Series DVR
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply
therefore with the applicable harmonized European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier
or to a designated collection point. For more information see: www.recyclethis.info.
1
User Manual of DS-7100HWI/HVI-SL Series DVR
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact
dealer.
This manual is applicable to DS-7104HWI-SL, DS-7108HWI-SL, DS-7116HWI-SL; DS-7116HVI-SL series
DVR.
This manual may contain several technically incorrect places or printing errors, and the content is subject to
change without notice. The updates will be added into the new version of this manual. We will readily
improve or update the products or procedures described in the manual.
2
User Manual of DS-7100HWI/HVI-SL Series DVR
Preventive and Cautionary Tips
Before connecting and operating your device, please be advised of the following tips:
•
•
•
•
•
Ensure unit is installed in a well-ventilated, dust-free environment.
Unit is designed for indoor use only.
Keep all liquids away from the device.
Ensure environmental conditions meet factory specifications.
Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it
may cause damage to the sensitive electronics within the unit.
•
•
•
•
Use the device in conjunction with an UPS if possible.
Power down the unit before connecting and disconnecting accessories and peripherals.
A factory recommended HDD should be used for this device.
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.
3
User Manual of DS-7100HWI/HVI-SL Series DVR
Product Key Features
General

PAL/NTSC adaptive video inputs.

H.264 video compression with high reliability and superior definition.

Each channel supports dual-stream.

Main stream supports encoding at up to WD1 resolution in real time and sub stream at
CIF/QCIF resolution.

Independent configuration for each channel, including resolution, frame rate, bit rate, image
quality, etc.

The quality of the input and output video is configurable.

Normal and event recording parameters configurable for per individual camera.

Encoding for both audio/video composite stream and video stream; audio and video
synchronization during composite stream encoding.

Watermark technology.
Local Monitoring

VGA output at up to 1920×1080P resolution.

1/4/6/8/9/16-division live view is supported, and the display sequence of screens is adjustable.

Live view screen can be switched in group, and manual switch and automatic cycle view is also
provided, the interval of automatic cycle can be adjusted.

Quick setting menu is provided for live view.

The selected live view channel can be shielded.

Motion detection, tamper-proof and video loss alarm functions.

Privacy mask.
HDD Management

1 SATA hard disk can be connected, with a maximum of 4TB storage capacity.

HDD quota management; different capacity can be assigned to different channels.
Recording and Playback

Holiday recording schedule configuration.

Normal and event video encoding parameters.

Multiple recording types: manual, normal and motion.

8 recording time periods with separated recording types.

Pre-record and post-record for motion detection for recording, and pre-record time for schedule
and manual recording.

Searching record files by event.

Customization of tags, searching and playing back by tags.

Locking and unlocking record files.

Searching and playing back record files by channel number, recording type, start time, end time,
etc.

Smart search for the selected area in the video.

Zooming in when playback.

Playing reversely.

Supports pause, slow forward, fast forward, skip forward, and skip backward when playback,
4
User Manual of DS-7100HWI/HVI-SL Series DVR
locating by dragging the mouse.

Up to 4/8/16-ch synchronous playback.
Backup

Export video data by USB storage device.

Export video clips when playback.

Management and maintenance of backup devices.
Alarm and Exception

Alarm for video loss, motion detection, tampering, video input/output standard mismatch, illegal
login, network disconnected, IP confliction, HDD error, and HDD full, etc.

Alarm event triggers full screen monitoring, audio alarm, notifying surveillance center and
sending email.

Automatic restore when system is abnormal.
Other Local Functions

Operable by mouse.

Three-level user management; admin user is allowed to create many operating accounts and
define their operating permission, which includes the limit to access any channel.

Operation, exceptions and log recording and searching.

Import and export of device configuration information.
Network Functions

1 self-adaptive 10M/100Mbps network interface.

IPv6 is supported.

TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, UPnP™, RTSP are
supported.

TCP, UDP and RTP for unicast.

Remote search, playback, download, locking and unlocking the record files, and downloading
files broken transfer resume.

Remote parameters setup; remote import/export of device parameters.

Remote viewing of the device status, system logs and alarm status.

Remote locking and unlocking of control panel and mouse.

Remote HDD formatting and program upgrading.

Remote system restart.

Alarm event and exception information can be sent to the remote host.

Remotely start/stop recording.

Upgrade by remote FTP server.

Two-way audio and voice broadcasting.

Embedded WEB server.
Development Scalability

SDK for Windows and Linux system.

Source code of application software for demo.

Development support and training for application system.
5
User Manual of DS-7100HWI/HVI-SL Series DVR
TABLE OF CONTENTS
Product Key Features ......................................................................................................... 4
C H A P T E R 1 ........................................................................................................................ 9
Introduction ............................................................................................................................... 9
1.1 Front Panel ................................................................................................................. 10
1.2 USB Mouse Operation ............................................................................................... 11
1.3 Input Method Description .......................................................................................... 11
1.4 Rear Panel .................................................................................................................. 12
1.5 Starting Up and Shutting Down the Device ............................................................... 13
C H A P T E R 2 ...................................................................................................................... 15
Getting Started ....................................................................................................................... 15
C H A P T E R 3 ...................................................................................................................... 20
Live View................................................................................................................................. 20
3.1 Introduction of Live View .......................................................................................... 21
3.2 Operations in Live View Mode .................................................................................. 22
3.2.1 Using the Mouse in Live View ........................................................................ 22
3.2.2 Using an Auxiliary Monitor ............................................................................ 23
3.2.3 Main/Aux Output Switching ........................................................................... 23
3.2.4 Quick Setting Toolbar in Live View Mode ..................................................... 24
3.3 Adjusting Live View Settings ..................................................................................... 27
3.4 Channel-zero Encoding .............................................................................................. 29
3.5 User Logout................................................................................................................ 30
C H A P T E R 4 ...................................................................................................................... 31
Record Settings....................................................................................................................... 31
4.1 Configuring Encoding Parameters ............................................................................. 32
4.2 Configuring Record Schedule .................................................................................... 34
4.3 Configuring Motion Detection Record ...................................................................... 38
4.4 Configuring Manual Record ...................................................................................... 40
4.5 Configuring Holiday Record ...................................................................................... 41
4.6 Files Protection .......................................................................................................... 44
C H A P T E R 5 ...................................................................................................................... 46
Playback .................................................................................................................................. 46
5.1 Playing Back Record Files ......................................................................................... 47
5.1.1 Playing Back by Channel ................................................................................ 47
5.1.2 Playing Back by Time ..................................................................................... 50
5.1.3 Playing Back by Normal Video Search ........................................................... 52
5.1.4 Playing Back by Event Search ........................................................................ 55
5.1.5 Playing Back by Tag ....................................................................................... 58
5.1.6 Playing Back by System Log .......................................................................... 62
5.2 Auxiliary Functions of Playback ................................................................................ 64
5.2.1 Playing Back Frame by Frame ........................................................................ 64
5.2.2 Smart Search ................................................................................................... 64
6
User Manual of DS-7100HWI/HVI-SL Series DVR
5.2.3 Digital Zoom ................................................................................................... 67
C H A P T E R 6 ...................................................................................................................... 68
Backup .................................................................................................................................... 68
6.1 Backing up Record Files ............................................................................................ 69
6.1.1 Quick Export ................................................................................................. 69
6.1.2 Backing up by Normal Video Search .............................................................. 71
6.1.3 Backing up by Event Search ......................................................................... 74
6.1.4 Backing up Video Clips................................................................................... 77
6.2 Managing Backup Devices ........................................................................................ 79
C H A P T E R 7 ...................................................................................................................... 83
Alarm Settings ........................................................................................................................ 83
7.1 Setting Motion Detection ........................................................................................... 84
7.2 Detecting Video Loss ................................................................................................. 86
7.3 Detecting Video Tampering........................................................................................ 87
7.4 Handling Exceptions .................................................................................................. 88
7.5 Setting Alarm Response Actions ................................................................................ 89
C H A P T E R 8 ...................................................................................................................... 90
Network Settings .................................................................................................................... 90
8.1 Configuring General Settings ..................................................................................... 91
8.2 Configuring Advanced Settings ................................................................................. 91
8.2.1 Configuring PPPoE Settings ........................................................................... 91
8.2.2 Configuring DDNS ......................................................................................... 92
8.2.3 Configuring NTP Server ................................................................................. 95
8.2.4 Configuring UPnP™ ....................................................................................... 95
8.2.5 Configuring Remote Alarm Host .................................................................... 97
8.2.6 Configuring Multicast ..................................................................................... 98
8.2.7 Configuring RTSP ........................................................................................... 98
8.2.8 Configuring Server and HTTP Ports ............................................................... 99
8.2.9 Configuring Email ........................................................................................... 99
8.3 Checking Network Traffic........................................................................................ 102
8.4 Network Detection ................................................................................................... 103
8.4.1 Testing Network Delay and Packet Loss ..................................................... 103
8.4.2 Exporting Network Packet .......................................................................... 103
8.4.3 Checking Network Status ............................................................................ 105
8.4.4 Checking Network Statistics ....................................................................... 106
C H A P T E R 9 .................................................................................................................... 107
HDD Management ............................................................................................................... 107
9.1 Initializing HDDs ................................................................................................... 108
9.2 Configuring Quota Mode ......................................................................................... 109
9.3 Checking HDD Status .............................................................................................. 111
9.4 Checking S.M.A.R.T. Information ........................................................................... 112
9.5 Detecting Bad Sector ............................................................................................... 113
9.6 Configuring HDD Error Alarms ............................................................................ 114
C H A P T E R 10 .................................................................................................................. 115
7
User Manual of DS-7100HWI/HVI-SL Series DVR
Camera Settings ................................................................................................................... 115
10.1 Configuring OSD Settings ..................................................................................... 116
10.2 Configuring Privacy Mask ..................................................................................... 117
10.3 Configuring Video Parameters ............................................................................... 118
C H A P T E R 1 1 ................................................................................................................. 119
Device Management and Maintenance .............................................................................. 119
11.1 Viewing System Information ................................................................................. 120
11.1.1 Viewing Device Information ....................................................................... 120
11.1.2 Viewing Camera Information ...................................................................... 120
11.1.3 Viewing Record Information ....................................................................... 120
11.1.4 Viewing Network Information .................................................................... 121
11.1.5 Viewing HDD Information .......................................................................... 121
11.2 Searching & Exporting Log Files .......................................................................... 123
11.3 Importing/Exporting Configuration Files .............................................................. 125
11.4 Upgrading System.................................................................................................. 127
11.4.1 Upgrading by Local Backup Device ........................................................... 127
11.4.2 Upgrading by FTP ....................................................................................... 127
11.5 Restoring Default Settings ..................................................................................... 129
C H A P T E R 1 2 ................................................................................................................. 130
Others .................................................................................................................................... 130
12.1 Configuring General Settings ................................................................................ 131
12.2 Configuring DST Settings...................................................................................... 132
12.3 Configuring More Settings .................................................................................... 133
12.4 Managing User Accounts ....................................................................................... 134
12.4.1 Adding a User ............................................................................................. 134
12.4.2 Deleting a User............................................................................................ 136
12.4.3 Editing a User.............................................................................................. 137
12.4.4 Changing Password of Admin ..................................................................... 137
12.5 Logging out/Shutting down/Rebooting Device ..................................................... 139
C H A P T E R 1 4 ................................................................................................................. 140
Appendix ............................................................................................................................... 140
Glossary ......................................................................................................................... 141
FAQ .............................................................................................................................. 142
8
User Manual of DS-7100HWI/HVI-SL Series DVR
C HAPTE R 1
Introduction
9
User Manual of DS-7100HWI/HVI-SL Series DVR
1.1 Front Panel
The front panel of DS-7100HWI/HVI-SL series DVR is shown in Figure 1.1:
Figure 1.1 Front Panel
Table 1.1 Description of Indicators
No.
Icon
Description
1
Indicator turns red when DVR is powered up.
2
Indicator lights in red when data is being read from or written to HDD.
3
Indicator blinks blue when network connection is functioning properly.
10
User Manual of DS-7100HWI/HVI-SL Series DVR
1.2 USB Mouse Operation
A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this device. To use a USB
mouse:
1. Plug USB mouse into one of the USB interfaces on the rear panel of the device.
2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible
reason may be that the two devices are not compatible, please refer to the recommended device list from
your provider.
The operation of the mouse:
Table 1.2 Description of the Mouse Control
Name
Action
Description
Single-Click
Live view: Select channel and show the quick set menu.
Menu: Select and enter a menu.
Left-Click
Double-Click
Live view: Switch single-screen and multi-screen.
Tamper-proof, privacy mask and motion detection: Select target area.
Click and Drag
Digital zoom-in: Drag and select target area.
Live view: Drag channel/time bar.
Right-Click
Scroll-Wheel
Live view: Show menu.
Single-Click
Menu: Exit current menu to upper level menu.
Live view: Previous screen.
Scrolling up
Right-click Menu: Previous item.
Scrolling down
Live view: Next screen.
Right-click Menu: Next item.
1.3 Input Method Description
Figure 1.2 Soft Keyboard
Description of the buttons on the soft keyboard:
Table 1.3 Description of the Soft Keyboard Icons
Icons
Description
Icons
Description
English
Capital English
Numbers
Symbols
Lowercase/Uppercase
Backspace
Space
Enter
Exit
11
User Manual of DS-7100HWI/HVI-SL Series DVR
1.4 Rear Panel
The rear panel of DS-7108HWI-SL is shown in Figure 1.3.
Figure 1.3 Rear Panel of DS-7108HWI-SL
Note: The DS-7104HWI-SL provides 4 video input interfaces and the DS-7116HWI/HVI-SL provides 16
video input interfaces on the rear panel.
Table 1.4 Description of Rear Panel
No.
Item
Description
1
VIDEO IN
BNC connector for analog video input.
2
VIDEO OUT
BNC connector for video output.
3
AUDIO IN
RCA connector for audio input.
4
LAN Interface
RJ45 10M / 100M Ethernet interface.
5
GND
Ground (needs to be connected when DVR starts up)
6
VGA
DB15 connector for VGA output. Display local video output and menu.
7
AUDIO OUT
RCA connector for audio output.
8
USB Interface
Connects USB mouse or USB flash memory devices.
9
12V
12VDC power supply.
12
User Manual of DS-7100HWI/HVI-SL Series DVR
1.5 Starting Up and Shutting Down the Device
Purpose:
Proper startup and shutdown procedures are crucial to expanding the life of the device.
Before you start:
Check that the voltage of the extra power supply is the same with the device’s requirement, and the ground
connection is working properly.
Starting up the device:
Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an
Uninterruptible Power Supply (UPS) be used in conjunction with the device. The Power indicator LED should
turn red indicating that the unit begins to start up.
Shutting down the device:
Steps:
1. Enter the Shutdown menu.
Menu > Shutdown
Figure 1.4 Shutdown Menu
2. Click the Shutdown button to enter the following dialog box:
Figure 1.5 Dialog Box for Shutdown
3. Click the Yes button. The following message box pops up:
Figure 1.6 Message Box for Power Off
4. Disconnect the power supply of the device.
Rebooting the device
13
User Manual of DS-7100HWI/HVI-SL Series DVR
In the Shutdown menu (Figure 1.4), you can also click Reboot to reboot the device.
14
User Manual of DS-7100HWI/HVI-SL Series DVR
C HAPTE R 2
Getting Started
15
User Manual of DS-7100HWI/HVI-SL Series DVR
The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard
starts once the device has loaded.
Operating the Setup Wizard:
Steps:
1.
Select the system resolution from the drop-down menu. The default resolution is 1280×1024/60Hz.
Click Apply to save the resolution settings.
Figure 2.1 Start Wizard Interface
2.
Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup
wizard.
You can also click Cancel to exit the Setup Wizard, or use the Setup Wizard next time by leaving the
“Start wizard when device starts?” checkbox checked and exit.
Figure 2.2 Start Wizard Interface
3.
Click Next button on the Wizard window to enter the Login window, as shown in Figure 2.3.
1)
Enter the admin password. By default, the password is 12345.
2)
To change the admin password, check the New Admin Password checkbox. Enter the new
password and confirm the password in the given fields.
16
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 2.3 Login Window
4.
Click the Next button to enter the Date and Time settings window, as shown in Figure 2.4.
Set the time zone, date format, system date and system time.
Figure 2.4 Date and Time Settings
5.
Click Next button which takes you back to the Network Setup Wizard window, as shown in Figure 2.5.
Set the network parameters, including the NIC type, IPv4 address, IPv4 subnet mask, default gateway,
etc. You can enable the DHCP to automatically obtain an IP address and other network settings from
that server.
17
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 2.5 Network Configuration
6.
Click Next button to enter the HDD Management window, shown in Figure 2.6.
To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD.
Figure 2.6 HDD Management
7.
Click Next button to enter the Record Settings window, as shown in Figure 2.7.
1)
Select the camera to configure.
2)
Check the checkbox to enable Start Recording.
3)
Select the recording mode to Normal or Motion Detection.
18
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 2.7 Record Settings
4)
Click Copy to copy the record settings of the current camera to other camera (s) if needed, as
shown in Figure 2.8.
Figure 2.8 Copy Record Settings
5)
8.
Click OK to return to the Record Settings window.
Click OK to complete the startup Setup Wizard.
19
User Manual of DS-7100HWI/HVI-SL Series DVR
C HAPTE R 3
Live View
20
User Manual of DS-7100HWI/HVI-SL Series DVR
3.1 Introduction of Live View
Live view shows you the video image getting from each camera in real time. The device automatically enters
Live View mode when powered on. It is also at the very top of the menu hierarchy, thus pressing the ESC
many times (depending on which menu you’re on) brings you to the Live View mode.
Live View Icons
In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the
record and alarm in the channel, so that you can know whether the channel is recorded, or whether there are
alarms occur as soon as possible.
Table 3.1 Description of Live View Icons
Icons
Description
Alarm (video loss, tampering or motion detection alarm)
Record (manual record, schedule record or motion detection record)
Alarm & Record
21
User Manual of DS-7100HWI/HVI-SL Series DVR
3.2 Operations in Live View Mode
In live view mode, the following functions can be realized:
•
•
•
Single Screen: showing only one screen on the monitor.
Multi-screen: showing multiple screens on the monitor simultaneously.
Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each
screen on the configuration menu before enabling the auto-switch.
Menu>Configuration>Live View>Dwell Time.
•
•
•
All-day Playback: play back the recorded videos for current day.
Start Recording: start all-day normal recording or motion detection recording for all channels.
Aux/Main Monitor switch: the DVR will check the connection of the output interfaces to define the
main and auxiliary output interfaces. When both VGA and CVBS are connected, the DVR detects the
VGA as the main video output (live view, playback and men operations) and the CVBS as the auxiliary
video output (live view and recording).
When the aux output is enabled, you can do some basic operation on the live view mode for the Aux output,
while no operation is allowed for the main output.
3.2.1 Using the Mouse in Live View
In the live view mode, use the mouse to right-click on the window to access the following menu:
Figure 3.1 Right-click Menu
Table 3.2 Mouse Operation in Live View
Name
Description
Menu
Enter the main menu of the system by right-clicking the mouse.
Single Screen
Switch to the single full screen by choosing channel number from the dropdown list.
Multi-screen
Adjust the screen layout by choosing from the dropdown list.
Previous Screen
Switch to the previous screen.
Next Screen
Switch to the next screen.
Start/Stop
Enable/disable the auto-switch of the screens.
22
User Manual of DS-7100HWI/HVI-SL Series DVR
Auto-switch
Note: The dwell time of the live view configuration must be set before using Start
Auto-switch.
Start Recording
Start all-day normal recording or motion detection recording for all channels.
Quick Set
Set the video output mode to Standard, Bright, Gentle or Vivid.
All-day Playback
Play back the video of the selected channel.
Aux Monitor
Switch to the auxiliary output mode and the operation for the main output is disabled.
Note: If you enter Aux monitor mode and the Aux monitor is not connected, the mouse
operation is disabled.
Note: If the corresponding camera supports intelligent function, the Reboot Intelligence option is included
when right-clicking mouse on this camera.
3.2.2 Using an Auxiliary Monitor
Certain features of the Live View are also available while in an Aux monitor. These features include:
• Single Screen: Switch to the single full screen by choosing channel number from the dropdown list.
• Multi-screen: Adjust the screen layout by choosing from the dropdown list.
• Previous Screen: Switch to the previous screen.
• Next Screen: Switch to the next screen.
• Quick Set: Set the video output mode to Standard, Bright, Gentle or Vivid.
• Menu Output Mode: Select the menu output mode to VGA, Main CVBS or Auto.
• Main Monitor: Switch to the Main Output mode and the operation for the auxiliary output is
disabled.
Note: In the live view mode of the main output monitor, the menu operation is not available while Aux output
mode is enabled.
3.2.3 Main/Aux Output Switching
When the VGA output is configured as the main output, you can perform the following operation to switch to
CVBS output as the main output.
Steps:
1.
Use the mouse wheel to double-click on the VGA output screen, and the following message box pops up:
Figure 3.2 Switch Main and Aux Output
2.
Use the mouse wheel to double-click on the screen again to switch to the Aux output, or click Cancel to
cancel the operation.
3.
Select the Menu Output Mode to Main CVBS from the right-click menu on the CVBS output monitor.
23
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 3.3 Right-click Menu on CVBS Output Monitor
4.
On the pop-up message box, click Yes to restart the device to enable the CVBS output as the main output.
Note: You can select the Menu Output Mode under Menu>Configuration>More Settings to Auto or VGA and
then restart the device to switch the main output back to VGA output.
3.2.4 Quick Setting Toolbar in Live View Mode
On the screen of each channel, there is a quick setting toolbar which shows when you right-click mouse on the
camera.
Figure 3.4 Quick Settings Toolbar
Table 3.3 Description of Quick Setting Toolbar Icons
Icons
Description
Icons
Enable Manual
Record
Digital Zoom
Description
Instant Playback
Image Settings
Icons
/
Description
Mute/Audio on
Close
Instant Playback
Instant Playback only shows the record in last five minutes. If no record is found, it means there is no
record during the last five minutes.
Digital Zoom
Digital Zoom can zoom in the selected area to the full screen. You can left-click and draw to select the
area for zooming in, as shown in Figure 3.5.
24
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 3.5 Digital Zoom
Image Settings
Image Settings icon can be selected to enter the Image Settings menu.
Steps:
1.
Set the period of a day for configuring independent image parameters so as to satisfy different light
conditions, e.g., daylight and night time. Two periods can be configured. When you have configured
Period 1, the Period 2 is remained as the Other Time.
2.
Select the mode from the drop-down menu according to different light conditions.
Four modes are selectable:

Standard: in general lighting conditions (default).

Indoor: the image is relatively smoother.

Dim Light: the image is smoother than the other three modes.

Outdoor: the image is relatively clearer and sharper. The degree of contrast and saturation is high.
Figure 3.6 Image Settings
3.
Adjust the image parameters including the brightness, contrast, saturation, hue, sharpness level and
denoising level by moving the sliding bar or increasing/decreasing the value.
Note: The adjustable value range is 0~255 for the brightness, contrast, saturation and hue, 0~15 for the
25
User Manual of DS-7100HWI/HVI-SL Series DVR
sharpness level and 0~5 for the denoising level.
4.
Copy image parameters.
1)
If you want to copy the image parameters of the current camera to other camera (s), click the Copy
button to enter the Copy to interface:
Figure 3.7 Copy Image Settings to Other Camera (s)
2)
Select the camera (s) to be configured with the image settings. You can also click the checkbox of
Analog to select all cameras.
3)
Click the OK button to finish the Copy settings.
Note: You can click the Restore button to restore the current image settings to default parameters.
26
User Manual of DS-7100HWI/HVI-SL Series DVR
3.3 Adjusting Live View Settings
Purpose:
Live View settings can be customized according to different needs. You can configure the output interface,
dwell time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc.
Steps:
1. Enter the Live View Settings interface.
Menu> Configuration> Live View
Figure 3.8 Live View-General
The settings available in this menu include:
• Video Output Interface: Select the output to configure the settings for. Two output interfaces
are selectable: VGA and Main CVBS.
• Live View Mode: Select different window-division mode from the drop-down list.
• Dwell Time: The time in seconds to dwell between switching of channels when enabling
auto-switch in Live View.
• Enable Audio Output: Enable/disable audio output for the selected video output.
Notes:
1. When the VGA output interface is used as the main video output and the Audio Output
for the VGA output interface is enabled, the VGA audio and AUDIO OUT can be used for
live view, playback and two-way audio.
2. When the VGA output is used as the main video output and the Audio Output for the
VGA output interface is disabled, the VGA output provides no audio and the AUDIO
OUT is used for two-way audio.
3. When the CVBS output is used as the main video output, the VGA audio is provided for
Aux video output in live view, and the AUDIO OUT is used as the main video output (for
live view, playback or two-way audio).
• Event Output: Select the output to show event video.
• Full Screen Monitoring Dwell Time: The time in seconds to show alarm event screen.
2. Setting Camera Order
27
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 3.9 Live View- Camera Order
To set the camera order:
1)
Click the View tab to enter the camera order settings interface.
2)
Select an output interface and select a screen layout.
3)
Click to select a screen in the right region and double-click to select a channel in the left region.
Thus the selected channel will be displayed in the corresponding screen.
Note:
4)
5)
means the channel will not be displayed.
You can click
to start live view of all channels and click
Click
to go to the previous or next page.
or
Click the Apply button to save the setting.
28
to stop live view of all channels.
User Manual of DS-7100HWI/HVI-SL Series DVR
3.4 Channel-zero Encoding
Purpose:
Sometimes you need to get a remote view of many channels in real time from web browser or CMS (Client
Management System) software, in order to decrease the bandwidth requirement without affecting the image
quality, channel-zero encoding is supported as an option for you.
Steps:
1. Enter the Live View Settings interface.
Menu> Configuration> Live View
2. Select the Channel-Zero Encoding tab.
Figure 3.10 Live View- Channel-Zero Encoding
3. Check the checkbox after Enable Channel-Zero Encoding.
4. Configure the Frame Rate, Max. Bitrate Mode and Max. Bitrate.
After you set the Channel-Zero encoding, you can get a view in the remote client or Web browser of all the
channels in one screen.
29
User Manual of DS-7100HWI/HVI-SL Series DVR
3.5 User Logout
Purpose:
After logging out, the monitor turns to the live view mode and if you want to do some operation, you need to
enter user name and password to log in again.
Steps:
1. Enter the Shutdown menu.
Menu>Shutdown
Figure 3.11 Shutdown
2. Click Logout.
Note: After you have logged out the system, menu operation on the screen is invalid. It is required a user
name and password to login the system.
30
User Manual of DS-7100HWI/HVI-SL Series DVR
C HAPTE R 4
Record Settings
31
User Manual of DS-7100HWI/HVI-SL Series DVR
4.1 Configuring Encoding Parameters
Purpose:
By configuring the encoding parameters you can define the transmission stream type, the resolution and so on.
Before you start:
1. Make sure that the HDD has already been installed. If not, please install a HDD and initialize it.
(Menu>HDD>General)
Figure 4.1 HDD- General
2. Check the storage mode of the HDD
1) Click Advanced to check the storage mode of the HDD.
2) For Quota storage mode, please set the maximum record capacity. For detailed information, see
Chapter 9.2 Configuring Quota Mode.
Figure 4.2 HDD- Advanced
Steps:
1. Enter the Record settings interface to configure the encoding parameters:
Menu>Record>Encoding
32
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 4.3 Encoding Parameters-Main Stream
2. Set encoding parameters for main stream
1)
Select Record to enter the main stream settings interface.
2)
Select the camera for configuration.
3)
Configure the following parameters for the Main Stream (Normal) and the Main Stream (Event):
•
•
•
•
•
•
•
•
Stream Type: Set the stream type to be Video or Video & Audio.
Resolution: Set recording at resolution of WD1, 4CIF, 2CIF, CIF or QCIF.
Bitrate Type: Set the bitrate type to be Variable or Constant.
Video Quality: Set the video quality of recording, with 6 levels configurable.
Frame Rate: Set the frame rate of recording.
Max. Bitrate Mode: Set the mode to General or Customize (32-3072Kbps).
Max Bitrate (Kbps): Select or customize the maximum bit rate for recording.
Max. Bitrate Range Recommended: A recommended Max. bitrate range is provided for
reference.
4)
Configure the pre-record, post-record time and expired time.
• Pre-record: The time you set to record before the scheduled time or event. For example, when
an alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the
camera records it at 9:59:55.
• Post-record: The time you set to record after the event or the scheduled time. For example,
when an alarm triggered the recording ends at 11:00, if you set the post-record time as 5
seconds, it records till 11:00:05.
• Expired Time (day): The expired time is the longest time for a record file to be kept in the
HDD, if the deadline is reached, the file will be deleted. You can set the expired time to 0, and
then the file will not be deleted. The actual keeping time for the file should be determined by
the capacity of the HDD.
33
User Manual of DS-7100HWI/HVI-SL Series DVR
• Record Audio: Check the checkbox to record the sound, or uncheck to record the image
without sound.
• Enable 960Mode: Enable the encoding at WD1 (PAL: 960×576, NTSC: 960×480) resolution.
You can also uncheck the checkbox to disable it.
5)
If you want to copy the current main stream settings to other camera (s), click Copy to enter the
Copy Camera interface. Select the camera (s) and click OK to finish the copy settings.
Figure 4.4 Copy Camera Settings
6)
On the Record settings interface, click Apply to save the settings.
Note: You can click the Restore button to restore the current main stream settings to the default
parameters.
3. Set encoding parameters for sub-stream
1)
Click the Substream tab to enter the Substream settings interface.
Figure 4.5 Encoding Parameters-Sub-stream
2)
Configure the parameters for the sub-stream. Refer to the steps of main stream settings.
3)
Click Apply to save the settings.
Note: You can click the Restore button to restore the current sub-stream settings to the default
parameters.
4)
If you want to copy the current sub-stream settings to other camera (s), click Copy to enter the
Copy Camera interface. Select the camera (s) and click OK to finish the copy settings.
4.2 Configuring Record Schedule
Purpose:
Set the record schedule, and then the camera automatically starts/stops recording according to the configured
schedule.
Steps:
1. Enter the Record Schedule interface.
34
User Manual of DS-7100HWI/HVI-SL Series DVR
Menu>Record>Schedule
2. Configure Record Schedule
1) Click Schedule to enter the record schedule settings interface.
Figure 4.6 Record Schedule
2) Choose the camera you want to configure.
3) Check the check box after the Enable Schedule item.
There are two ways to configure the record schedule.
Task 1: Edit the Schedule
Steps:
1) Click Edit.
2) In the message box, you can choose the day which you want to set schedule.
3) To schedule an all-day recording, check
checkbox to enable all-day recording.
4) Set the Type in the dropdown list, including Normal and Motion.
Note: To enable Motion triggered recording, you must configure the motion detection settings as
well. For detailed information, refer to Chapter 7.1.
Figure 4.7 Edit Schedule
5) To arrange other schedule, leave the All Day checkbox blank and set the Start/End time and Type.
Note: Up to 8 periods can be configured for each day. And the time periods can’t be overlapped each other.
Repeat the above steps 2)-5) to schedule recording for other days in the week. If the schedule can also be set
to other days, click Copy.
35
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 4.8 Copy Schedule to Other Days
Note: The Holiday option is available in the Schedule dropdown list when you have enabled holiday schedule
in Holiday Settings. Refer to Chapter 4.5 Configuring Holiday Record.
Figure 4.9 Holiday Settings
6) Click OK to save setting and back to upper level menu.
Task 2: Draw the Schedule
Steps:
1) Click the icon on the right to select a record type, including Normal, Motion and None.
Note: To enable Motion triggered recording, you must configure the motion detection settings. For
detailed information, refer to Chapter 7.1.
2) Use the mouse to drag and draw time periods.
Note: Up to 8 periods can be configured for each day.
Figure 4.10 Draw the Schedule
3) You can repeat the above steps to set schedule for other channels. If the settings can also be used to
36
User Manual of DS-7100HWI/HVI-SL Series DVR
other channels, click Copy to enter the Copy Camera interface and then choose the channel to
which you want to copy.
Figure 4.11 Copy Schedule to Other Channels
4) Click Apply in the Record Schedule interface to save the settings.
37
User Manual of DS-7100HWI/HVI-SL Series DVR
4.3 Configuring Motion Detection Record
Purpose:
Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event
takes place, the device can analyze it and perform some response actions to handle it. Enabling motion
detection function can trigger certain channels to start recording, or trigger full screen monitoring, audio
warning, notify the surveillance center and so on. In this chapter, you can follow the steps to schedule a record
which triggered by the detected motion.
Steps:
1.
Enter the Motion Detection interface.
Menu>Camera>Motion
Figure 4.12 Motion Detection
2.
Configure Motion Detection:
1) Choose camera you want to configure.
2) Check the checkbox after Enable Motion Detection.
3) Drag and draw the area for motion detection by mouse. If you want to set the motion detection
for all the area shot by the camera, click Full Screen. To clear the motion detection area, click
Clear.
Note: By default, the motion detection is configured in full screen.
Figure 4.13 Motion Detection- Mask
38
User Manual of DS-7100HWI/HVI-SL Series DVR
4) Click Handling, and the message box for channel information will pop up.
Figure 4.14 Motion Detection Handling
5) Select the channels which you want the motion detection event to trigger recording.
6) Click Apply to save the settings.
7) Click OK to back to the upper level menu.
8) Exit the Motion Detection menu.
3.
Enter Schedule settings interface.
Menu> Record> Schedule>Record
Figure 4.15 Record Schedule
1) Check the checkbox after the Enable Schedule item.
2) Click Edit.
Figure 4.16 Edit Schedule- Motion Detection
3) In the message box, you can choose the day to which you want to set schedule.
39
User Manual of DS-7100HWI/HVI-SL Series DVR
4) Set the Type as Motion.
5) To schedule an all-day recording, check the checkbox after the All Day item.
Figure 4.17 Edit Schedule- All Day
6) To arrange other schedule, leave the All Day checkbox blank and set the Start/End time.
Note: Up to 8 periods can be configured for each day. And the time periods can’t be overlapped
each other.
Repeat the above steps3)-6) to schedule motion detection triggered recording for all the week. If
the schedule can also be set to other days, click Copy.
Figure 4.18 Copy Schedule to Other Days
7) Click OK to back to upper level menu.
If you can to copy the same schedule settings to other camera (s), click Copy to enter the Copy Camera
interface, and then select the camera (s) you want to copy.
Figure 4.19 Copy Schedule to Other Channels
4.4 Configuring Manual Record
Purpose:
Follow the steps to set parameters for the manual record. When using manual record, you need to manually
cancel the record. The manual recording is prior to the scheduled recording.
40
User Manual of DS-7100HWI/HVI-SL Series DVR
Steps:
1.
Enter the Manual settings interface.
Menu> Manual
Figure 4.20 Manual Record
2.
Enable recording for camera (s).
Click the status button beside each camera number to change
to
, or you can enable
recording for all cameras by clicking the status bar before Analog to change it to
3.
.
Set recording mode to manual.
By default, the camera is enabled with recording by schedule (
change it to
and click again to enable the recording to manual (
). Click the
status bar to
).
: recording by schedule.
: recording by manual operation.
Note: After rebooting, all the manual records enabled are canceled.
4.
Start all-day normal recording or all-day motion detection recording of all channels.
1) Click
for
or
.
Figure 4.21 Start Normal or Motion Detection Recording
2) Click Yes to enable all-day normal recording or all-day motion detection recording of all
channels.
4.5 Configuring Holiday Record
Purpose:
You may want to have different plan for recording on holiday. Follow the steps to configure the record
schedule on holiday.
Steps:
1.
Enter the Record setting interface.
Menu>Record
2.
Choose Holiday on the left bar.
41
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 4.22 Holiday Settings
3.
Enable Edit Holiday schedule.
1) Click
to enter the Edit interface.
Figure 4.23 Edit Holiday Settings
2) Check the checkbox after Enable.
3) Select Mode from the dropdown list.
There are three different modes for the date format to configure holiday schedule.
4) Set the start and end date.
5) Click Apply to save settings.
6) Click OK to exit the Edit interface.
4.
Enter Record Schedule settings interface.
Menu> Record> Schedule
1) Select Record.
2) Check the checkbox after Enable Schedule.
3) Click Edit.
4) Select Holiday from the Schedule dropdown list.
42
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 4.24 Edit Schedule- Holiday
5) Select Motion or Normal from the Type dropdown list.
6) If you need all day recording, check the All Day checkbox. Otherwise leave it blank.
7) Set start/end time for holiday schedule.
Note: Up to 8 periods can be configured for each day. And the time periods can’t be overlapped each other.
In the time table of the channel, both holiday schedule and normal day schedule are displayed.
Repeat the above steps4)-7) to set Holiday schedule for other channel. If the holiday schedule can also be used
to other channels, click Copy and choose the channel you want to apply the settings.
43
User Manual of DS-7100HWI/HVI-SL Series DVR
4.6 Files Protection
Purpose:
You can lock the recorded files or set the HDD property to Read-only to protect the record files from being
overwritten.
Protect file by locking the record files:
Steps:
1.
Enter Playback setting interface.
Menu> Playback
Figure 4.25 Playback
2.
Select the channels by checking the checkbox to
.
3.
Configure the record type, file type and start/end time.
4.
Click Search to show the results.
Figure 4.26 Playback- Search Result
5.
Protect the record files.
1)
Find the record files you want to protect, and then click the
indicating that the file is locked.
44
icon which will turn to
,
User Manual of DS-7100HWI/HVI-SL Series DVR
Note: The record files of which the recording is still not completed can’t be locked.
2)
Click
to change it to
to unlock the file and the file is not protected.
Figure 4.27 Unlocking Attention
45
User Manual of DS-7100HWI/HVI-SL Series DVR
C HAPTE R 5
Playback
46
User Manual of DS-7100HWI/HVI-SL Series DVR
5.1 Playing Back Record Files
5.1.1 Playing Back by Channel
Purpose:
Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported.
Instant playback by channel:
Steps:
Choose a channel in live view mode using the mouse and click the
button in the quick setting toolbar.
Note: Only record files recorded during the last five minutes on this channel will be played back.
Figure 5.1 Instant Playback Interface
All-day Playback by channel
1. Enter the All-day Playback interface.
Right click a channel in live view mode and select All-day Playback from the menu, as shown in Figure
5.2.
47
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.2 Right-click Menu under Live View
Under multi-screen live view, record files of the selected channel will be played back.
2. Playback management.
The toolbar in the bottom part of Playback interface can be used to control playing progress, as shown in
Figure 5.3.
Figure 5.3 All-day Playback Interface
The channel and time selection menu displays by moving the mouse to the right of the playback interface.
Click the channel(s) if you want to switch playback to another channel or execute simultaneous playback of
multiple channels, as shown in Figure 5.4.
48
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.4 All-day Playback Interface with Channel List
Dates marked in different colors:
: No record files in this day.
: There is record file(s) in this day (not current day).
: There is only event recording file(s) in this day (not current day).
: Mouse cursor is located.
Figure 5.5 Toolbar of All-day Playback
Table 5.1 Detailed Explanation of All-day-playback Toolbar
Button
Operation
Button
/
Audio on /Mute
/
Start/Stop
Add default tag
Pause reverse
Reverse play/
Single-frame
reverse play
Button
Operation
Button
Operation
30s forward
30s reverse
Add customized
Tag
Slow
tag
management
forward
clipping
Pause play/
play/
/
Operation
Play/
/
Single-frame
Stop
Fast
forward
play
Previous day
Next day
Process bar
Video type bar
Hide
Exit
Notes:
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
49
User Manual of DS-7100HWI/HVI-SL Series DVR
2. About video type bar:
recording (motion);
represents normal recording (manual or schedule);
represents event
represents smart search recording.
5.1.2 Playing Back by Time
Purpose:
Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel
switch are supported.
Steps:
1. Enter playback interface.
Menu>Playback
2. Check the checkbox before the channel to select channel(s) and click the Detail button to view the
record information of the channel(s). You can click Previous or Next to select the day for viewing the
record information.
Figure 5.6 Record Information
3. Click Back to return to the playback interface.
4. Set search conditions and click the Playback button to enter Playback interface.
50
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.7 Video Search by Time
In the Playback interface:
The toolbar in the bottom part of Playback interface can be used to control playing process, as shown in
Figure 5.9.
Figure 5.8 Interface of Playback by Time
Figure 5.9 Toolbar of Playback by Time
51
User Manual of DS-7100HWI/HVI-SL Series DVR
Table 5.2 Detailed Explanation of Playback-by-time Toolbar
Button
Operation
Button
Operation
/
Start/Stop clipping
Audio
/
on/Mute
Add default
Button
Add customized tag
tag
Operation
Button
Operation
30s
30s forward
reverse
Tag
Slow
management
forward
Pause
reverse
Pause
play/Reverse
/
play/
/
play/Play/Single-frame
Fast
Stop
forward
play
Single-frame
reverse play
Video search
Exit
Progress
Hide
bar
Video type
bar
Notes:
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
2. About video type bar:
recording (motion);
represents normal recording (manual or schedule);
represents event
represents smart search recording.
5.1.3 Playing Back by Normal Video Search
Purpose:
Play back video files searched out by restricting recording type and recording time. The video files in the
result list are played back sequentially and channel switch is supported. Recording types contain Normal,
Motion and Manual.
Steps:
1. Enter Record File Search interface.
Menu>Playback
Set search condition and click Search button to enter the Search Result interface.
Figure 5.10 Normal Video Search
52
User Manual of DS-7100HWI/HVI-SL Series DVR
2. Choose a record file you want to play back.
If there is only one channel in the search result, clicking
button takes you to Full-screen Playback
interface of this channel.
If more than one channel is optional, clicking
button takes you to step 3 and step 4.
Figure 5.11 Result of Normal Video Search
3. Choose channels for simultaneous playback.
Note: Optional channels for simultaneous playback are the same as the channels chosen to search
record files in step 1. And the channel with the recorded file selected in step 2 is the main channel
during multi-channel playback and it is displayed at the upper left corner.
Figure 5.12 Select Channels for Synchronous Playback
4. Synchronous Playback interface.
The toolbar in the bottom part of Playback interface can be used to control playing process.
53
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.13 4-ch Synchronous Playback Interface
The hidden list of recorded files displays by moving the mouse to the right of the playback interface.
Figure 5.14 4-ch Synchronous Playback Interface with Video List
Figure 5.15 Toolbar of Normal Playback
Table 5.3 Detailed Explanation of Normal Playback Toolbar
Button
Operation
Button
Operation
/
Audio on/Mute
/
Start/Stop clipping
/
Add default tag
Add customized tag
Pause reverse
Pause
play/Reverse play/
Single-frame reverse
/
play/Play/Single-frame
play
54
Button
Operation
30s forward
Tag
management
Stop
Button
Operation
30s reverse
Slow forward
Fast forward
User Manual of DS-7100HWI/HVI-SL Series DVR
play
Previous file
Next file
Hide toolbar
Progress bar
Video search
Exit
Video type
bar
Note:
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
2. About video type bar:
recording (motion);
represents normal recording (manual or schedule);
represents event
represents smart search recording.
5.1.4 Playing Back by Event Search
Purpose:
Play back record files on one or several channels searched out by restricting event type (motion detection).
Channel switch is supported.
Steps:
1. Enter the playback interface.
Menu>Playback
2. Select Event tab to enter the Event Playback interface.
3. Select Motion as the event type.
4. Set the start time and end time of the record files.
5. Select the camera (s) for searching.
Figure 5.16 Video Search by Motion
6. Click Search button to enter the Search Result interface.
The Pre-play and post-play can be configured. The Pre-play refers to the time configured before the
defined start time of event search, and the Post-play refers to the time configured after the defined end
time of event search. For example, when the start time and end time of event search are set to 12:00:00 13:00:00, and the pre-play and post-play time is set to 30s and 20s respectively, then the actual playback
of event video file is 11:59:30 ~ 13:00:20.
55
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.17 Video Search Result by Motion
7. You can select an item from the list and click Details to view detailed information of the record file, e.g.,
start time, end time, file size, etc.
Figure 5.18 Event Details
8. Or you can directly click the
button of each file item to enter its playback interface. The toolbar in
the bottom part of Playback interface can be used to control playing process.
56
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.19 Interface of Playback by Event (1)
The hidden list of events will be displayed by moving the mouse to the right of the playback
interface.
Figure 5.20 Interface of Playback by Event (2)
Figure 5.21 Toolbar of Playback by Event
Table 5.4 Detailed Explanation of Playback-by-event Toolbar
Button
Operation
Button
Operation
/
Audio on/Mute
/
Start/Stop clipping
Add default tag
Add customized tag
57
Button
Operation
30s forward
Tag
management
Button
Operation
30s reverse
Slow forward
User Manual of DS-7100HWI/HVI-SL Series DVR
Pause reverse
Pause
play/Reverse play/
/
/
Single-frame reverse
play/Play/Single-frame
Stop
Fast forward
Event search
Exit
play
play
Previous event
Next event
Hide
Progress bar
Video type
bar
Notes:
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
3. About video type bar:
recording (motion);
represents normal recording (manual or schedule);
represents event
represents smart search recording.
5.1.5 Playing Back by Tag
Purpose:
Video tag allows you to record related information like people and location of a certain time point during
playback. You are also allowed to use video tag(s) to search for record files and position time point.
Before playing back by tag:
1. Enter Playback interface.
Figure 5.22 Interface of Playback by Event
Click
button to add default tag.
Click
button to add customized tag and input tag name.
Note: Max. 64 tags can be added to a single video file.
2. Tag management.
Click
button to check, edit and delete tag(s).
58
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.23 Tag Management Interface
To play back by tag:
Steps:
1. Enter Playback interface.
Menu>Playback
Click Tag tab to enter Playback by Tag interface.
Choose channels, tag type and time, and click Search to enter Search Result interface.
Note: Two tag types are selectable: All and Tag Keyword. Input keyword if you choose Tag Keyword.
Figure 5.24 Video Search by Tag
2. Set playback conditions and tag management.
Choose the tag name of the recorded file you want to play back; it can be edited or deleted.
Pre-play and post-play time can be set according to actual needs.
Note: Pre-play time and post-play time is added to the time point of the tag.
59
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.25 Result of Video Search by Tag
3. Playback by tag.
Choose a tag and click
button to play back the related record file.
Figure 5.26 Interface of Playback by Tag
The hidden list of tags will be displayed by moving the mouse to the right of the playback interface.
60
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.27 Interface of Playback by Tag with Video List
Figure 5.28 Toolbar of Playback by Tag
Table 5.5 Detailed Explanation of Playback-by-tag Toolbar
Button
Operation
Button
Operation
/
Audio on/Mute
/
Start/Stop clipping
Add default tag
Add customized tag
Pause reverse
Single-frame reverse
play
Operation
Button
30s forward
Tag
management
Operation
30s reverse
Slow forward
Pause
play/Reverse play/
/
Button
/
play/Play/Single-frame
Stop
Fast forward
Tag search
Exit
play
Previous tag
Next tag
Hide
Progress bar
Video type
bar
Notes:
1.
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
2.
About video type bar:
recording (motion);
represents normal recording (manual or schedule);
represents smart search recording.
61
represents event
User Manual of DS-7100HWI/HVI-SL Series DVR
5.1.6 Playing Back by System Log
Purpose:
Play back record file(s) associated with channels after searching system logs.
Steps:
1. Enter Log Search interface.
Menu>Maintenance>Log Information
Figure 5.29 System Log Search Interface
2. Set search time and type and click Search button.
Figure 5.30 Result of System Log Search
3. Choose a log with record file and click
button to enter Playback interface.
Note: If there is no record file at the time point of the log, the message box “No result found” will pop up.
The toolbar in the bottom part of Playback interface can be used to control playing process.
62
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.31 Interface of Playback by Log
63
User Manual of DS-7100HWI/HVI-SL Series DVR
5.2 Auxiliary Functions of Playback
5.2.1 Playing Back Frame by Frame
Purpose:
Play video files frame by frame, in order to check image details of the video when abnormal events happen.
Steps:
Go to Playback interface. If you choose playback of the record file: click button
and
until the speed
changes to Single frame and one click on the playback screen represents playback of one frame. If you choose
adverse playback of the record file: click button
and
until the speed changes to Single frame and
one click on the playback screen represents adverse playback of one frame. It is also feasible to use button
in toolbar.
5.2.2 Smart Search
Purpose:
In order to locate motion detection event easily and accurately in the playback progress bar, you are allowed
to analyze a certain area (scene) dynamically, and to get all of the related motion detection events that
occurred in this area.
Steps:
1. Go to normal playback or all-day playback interface.
Note: The smart search function is available for single-channel playback only.
Figure 5.32 Playback Interface
2. Right-click mouse and select Smart Search to go to analysis area selection interface.
64
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.33 Right-click Menu in All-day Playback and Normal Playback Interface
3. You can click button
button
to set the full screen as target searching area. After drawing area(s), click
to execute smart search in this area.
Note: Multi-area and full-screen searching modes are supported.
Figure 5.34 Draw Area of Smart Search
Results of intelligent analysis:
Video type bar:
: Normal record file;
: Event record file;
: Dynamic record file.
The hidden list of record files display when moving the mouse to the right of the playback interface.
65
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 5.35 Smart Search Result with Video List
Figure 5.36 Toolbar of Smart Search Playback
Table 5.6 Detailed Explanation of Smart-search-playback Toolbar
Button
Operation
Button
Operation
/
Audio on/Mute
/
Start/Stop clipping
Add default tag
Add customized tag
Pause reverse
Single-frame reverse
play
Operation
Button
30s forward
Tag
management
Operation
30s reverse
Slow forward
Pause
play/Reverse play/
/
Button
/
play/Play/Single-frame
Stop
Fast forward
Video search
Exit
Video type
Smart search
bar
bar
play
Previous smart
Next smart search
search result
result
Hide
Progress bar
Notes:
1.
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
2.
About video type bar:
recording (motion);
represents normal recording (manual or schedule);
represents smart search recording.
66
represents event
User Manual of DS-7100HWI/HVI-SL Series DVR
5.2.3 Digital Zoom
Steps:
1. Right click the mouse on a channel under playback and choose Digital Zoom to enter Digital Zoom
interface.
2. Use the mouse to draw a red rectangle and the image within it will be enlarged up to 16 times.
Figure 5.37 Draw Area for Digital Zoom
Figure 5.38 Right-click Menu in Playback Mode
Right-click menu:
Note: This menu differs slightly from one playback interface to another.
Table 5.7 Detailed Explanation of Right-click Menu under Playback
Button
Function
Return to Playback interface
Enter Digital Zoom interface
Smart Search against a specified area
Show & hide control interface
Exit the video playback interface
67
User Manual of DS-7100HWI/HVI-SL Series DVR
CHAPTER6
Backup
68
User Manual of DS-7100HWI/HVI-SL Series DVR
6.1 Backing up Record Files
Before you start:
Please insert the backup device(s) into the device.
6.1.1 Quick Export
Purpose:
Export record files to backup device (s) quickly.
Steps:
1. Enter Video Export interface
Menu>Export>Normal
Figure 6.1 Quick Export Interface
2. Choose the channel(s) you want to back up and click Quick Export button.
Notes:
1. The time duration of record files on a specified channel cannot exceed 24 hours. Otherwise, the
message box “Max. 24 hours are allowed for quick export.” will pop up.
2. The number of channels for synchronous export cannot exceed 4. Otherwise, the message box
“Max. 4 channels are allowed for synchronous quick export.” will pop up.
69
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 6.2 Quick Export using USB1-1
3. In the Export interface, choose backup device and click Export button to start exporting.
Note: Here we use USB Flash Drive and please refer to the next section Normal Backup for more
backup devices supported by the device.
4. Stay in the Exporting interface until all record files are exported to the USB flash drive.
Figure 6.3 Export Finished
5. Check backup result.
Choose the record file in Export interface and click button
to check it.
Figure 6.4 Checkup of Quick Export Result Using USB1-1
70
User Manual of DS-7100HWI/HVI-SL Series DVR
6.1.2 Backing up by Normal Video Search
Purpose:
The record files can be backed up to USB devices (USB flash drives, USB HDDs, USB writer).
Backup using USB flash drives, USB HDDs and USB writer.
Steps:
1. Enter Export interface.
Menu>Export>Normal
Figure 6.5 Normal Video Search for Backup
2. Set search conditions and click Search button to enter the search result interface.
3. Select record files you want to back up.
Click button
to play the record file if you want to check it.
Check the checkbox before the record files you want to back up.
Note: The size of the currently selected files is displayed in the lower-left corner of the window.
71
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 6.6 Result of Normal Video Search for Backup
4. Export the record files.
Click Export button and start backup.
Note: If the inserted device is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
You can also format USB flash drives or USB HDDs via the device. USB writer and SATA writer
cannot be formatted.
Figure 6.7 Export by Normal Video Search using USB Flash Drive
72
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 6.8 Export by Normal Video Search using USB Writer
Stay in the Exporting interface until all record files are exported with pop-up message box “Export
finished”.
Figure 6.9 Export Finished
5. Check backup result.
Choose the record file in Export interface and click button
to check it.
Figure 6.10 Checkup of Export Result using USB Flash Drive
73
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 6.11 Checkup of Export Result using USB Writer
6.1.3 Backing up by Event Search
Purpose:
Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), or SATA
writer. Quick Backup and Normal Backup are supported.
Steps:
1. Enter Export interface.
Menu>Export>Event
2. Select Motion as the event type.
3. Set the start time and end time of the record files.
4. Select the camera (s) for searching.
Figure 6.12 Event Search for Backup
5. Click Search button to enter the Search Result interface.
74
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 6.13 Result of Event Search
6. Select record files to export.
You can enter the Export interface by the following two ways:

Select motion detection event (s) from the list and click Quick Export button to enter the Export
interface, as shown in Figure 6.15.

(1) Click the Details button to enter the interface with detailed information of the record file, e.g.,
start time, end time, file size, etc.
Note: The size of the currently selected files is displayed in the lower-left corner of the window.
(2) Select record file (s) from the list and click Export button to enter the Export interface, as
shown in Figure 6.15.
Figure 6.14 Event Details Interface
7. Export the selected record files.
Click the Export button and start backing up.
Note: If the inserted USB device is not recognized:
• Click the Refresh button.
• Reconnect device.
75
User Manual of DS-7100HWI/HVI-SL Series DVR
• Check for compatibility from vendor.
You can also format USB flash drive or USB HDDs via the device.
Figure 6.15 Export by Event Using USB Flash Drive
Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”.
Figure 6.16 Export Finished
8. Check backup result.
Choose the record file in Export interface and click button
to check it.
Figure 6.17 Checkup of Event Export Result Using USB Flash Drive
76
User Manual of DS-7100HWI/HVI-SL Series DVR
6.1.4 Backing up Video Clips
Purpose:
You may also select video clips to export directly during Playback, using USB devices (USB flash drives,
USB HDDs, USB writer).
Steps:
1. Enter Playback interface.
Please refer to Chapter 5.
2. During playback, use buttons
and
in the playback toolbar to start or stop clipping record file(s).
3. Exit Playback interface after finishing clipping and you will then be prompted to save the clips.
Note: A maximum of 30 clips can be selected for each channel.
Figure 6.18 Interface of Playback by Time
4. Click Yes to save video clips and enter Export interface, or click No to quit and do not save video clips.
Figure 6.19 Attention to Video Clip Saving
5. Export the video clips.
Click Export button and start backing up.
Note: If the inserted USB device is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
You can also format USB flash drive or USB HDDs via the device.
77
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 6.20 Export Video Clips Using USB Flash Drive
Stay in the Exporting interface until all record files are exported with pop-up message “Export
finished”.
Figure 6.21 Export Finished
6. Check backup result.
Figure 6.22 Checkup of Video Clips Export Result Using USB Flash Drive
78
User Manual of DS-7100HWI/HVI-SL Series DVR
6.2 Managing Backup Devices
Management of USB flash drives, and USB HDDs.
1.
Enter Search Result interface of record files.
Menu>Export>Normal
Set search condition and click Search button to enter Search Result interface.
Note: At least one channel shall be selected.
Figure 6.23 Normal Video Search
2.
Select record files you want to back up.
Click Export button to enter Export interface.
Note: At least one record file shall be selected.
Figure 6.24 Result of Normal Video Search for Backup
79
User Manual of DS-7100HWI/HVI-SL Series DVR
3.
Backup device management.
Click New Folder button if you want to create a new folder in the backup device.
Select a record file or folder in the backup device and click button
Select a record file in the backup device and click button
if you want to delete it.
to play it.
Click Format button to format the backup device.
Note: If the inserted USB device is not recognized:
• Click the Refresh button.
• Reconnect device.
• Check for compatibility from vendor.
Figure 6.25 USB Flash Drive Management
Management of USB writers
1.
Enter Search Result interface of record files.
Menu>Export>Normal
Set search condition and click Search button to enter Search Result interface.
Note: At least one channel shall be selected.
80
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 6.26 Normal Video Search for Backup
2.
Select record files you want to back up.
Click Export button to enter Export interface.
Note: At least one record file shall be selected.
Figure 6.27 Result of Normal Video Search for Backup
3.
Backup device management.
Click Erase button if you want to erase the files from a re-writable CD/DVD.
Note: There must be a re-writable CD/DVD when you make this operation.
Note: If the inserted USB writer is not recognized:
• Click the Refresh button.
• Reconnect device.
81
User Manual of DS-7100HWI/HVI-SL Series DVR
• Check for compatibility from vendor.
Figure 6.28 USB Writer Management
82
User Manual of DS-7100HWI/HVI-SL Series DVR
CHAPTER7
Alarm Settings
83
User Manual of DS-7100HWI/HVI-SL Series DVR
7.1 Setting Motion Detection
Steps:
1. Enter Motion Detection interface and choose a camera you want to set motion detection.
Menu> Camera> Motion
Figure 7.1 Motion Detection Setup Interface
2. Set motion detection area and sensitivity.
1)
Check the checkbox of Enable Motion Detection to enable motion detection, use the mouse to
draw detection area(s) and drag the sensitivity bar to set sensitivity.
2)
Click the
icon of Handling to set alarm response actions.
Figure 7.2 Set Detection Area and Sensitivity
3. Click Trigger Channel tab and select one or more channels which will start to record or become
full-screen monitoring when motion alarm is triggered.
Figure 7.3 Set Trigger Camera of Motion Detection
84
User Manual of DS-7100HWI/HVI-SL Series DVR
4. Set up arming schedule of the channel.
1)
Select Arming Schedule tab to set the channel’s arming schedule.
2)
Choose one day of a week and up to eight time periods can be set within each day.
Note: Time periods shall not be repeated or overlapped.
Figure 7.4 Set Arming Schedule of Motion Detection
5. Click Handling tab to set up alarm response actions of motion alarm (please refer to Chapter 7.5).
1)
Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy
button to copy an arming schedule to other days.
2)
Click the OK button to complete the motion detection settings of the channel.
6. If you want to set up motion detection for another channel, repeat the above steps or just copy the above
settings to it.
Note: You are not allowed to copy the “Trigger Channel” action.
Figure 7.5 Copy Settings of Motion Detection
85
User Manual of DS-7100HWI/HVI-SL Series DVR
7.2 Detecting Video Loss
Purpose:
Detect video loss of a channel and take alarm response action(s).
Steps:
1. Enter Video Loss interface of Camera Management.
Menu> Camera> Video Loss
Figure 7.6 Video Loss Setup Interface
2. Select a channel you want to detect.
3. Check the checkbox of Enable Video Loss Alarm.
4. Click the
icon of Handling to enter the Handling interface.
5. Set the arming schedule and alarm response actions. Please refer to Step4 and Step5 of Chapter 7.1
Setting Motion Detection.
Figure 7.7 Set Arming Schedule of Video Loss
6. Click Apply to save the video loss alarm settings.
86
User Manual of DS-7100HWI/HVI-SL Series DVR
7.3 Detecting Video Tampering
Purpose:
Trigger alarm when the lens is covered and take alarm response action(s).
Steps:
1. Enter Video Tampering interface of Camera Management.
Menu> Camera> Tamper-proof
Figure 7.8 Tamper-proof Setup Interface
2. Select a channel you want to detect video tampering.
3. Check the checkbox of Enable Tamper-proof.
Note: By default, the tamper-proof detection is configured in full screen.
4. Move the sensitivity bar and choose a proper sensitivity level.
5. Click the
icon of Handling to enter the Handling interface.
6. Set the arming schedule and alarm response actions. Please refer to Step4 and Step5 of Chapter 8.1
Setting Motion Detection.
7. If you want to set tamper-proof handling method for another channel, repeat above steps or click Copy
to copy the above settings to it.
Figure 7.9 Copy Settings of Video Tampering
87
User Manual of DS-7100HWI/HVI-SL Series DVR
7.4 Handling Exceptions
Purpose:
Exception settings refer to the handling method of various exceptions, including:
• HDD Full: The HDD is full.
• HDD Error: Writing HDD error, unformatted HDD, etc.
• Network Disconnected: Disconnected network cable.
• IP Conflicted: Duplicated IP address.
• Illegal Login: Incorrect user ID or password.
• Input / Output Video Standard Mismatch: I/O video standards do not match.
• Record Exception: No space for saving recorded file.
Steps:
Enter Exceptions interface of System Configuration and handle various exceptions.
Menu> Configuration> Exceptions
Please refer to Chapter 7.5 for detailed alarm response actions.
Figure 7.10 Exceptions Setup Interface
88
User Manual of DS-7100HWI/HVI-SL Series DVR
7.5 Setting Alarm Response Actions
Purpose:
The alarm response actions will be activated when an exception occurs, including Full Screen Monitoring,
Audible Warning, Notify Surveillance Center, and Send Email.
Full Screen Monitoring
When an alarm event (motion detection/tamper-proof/video loss detection) is triggered, the local monitor
(VGA or BNC monitor) display in full screen the video image from the alarming channel configured for full
screen monitoring.
If alarms are triggered simultaneously in several channels, their full-screen images will be switched at an
interval of 10 seconds (default dwell time). A different dwell time can be set by going to Menu>
Configuration>Live View>Full Screen Monitoring Dwell Time.
Auto-switch will terminate once the alarm stops and you will be taken back to the Live View interface.
Note: For motion detection alarm, you must select the channel(s) you want to make full screen monitoring
(Menu>Camera>Motion>Handling>Trigger Channel).
Audible Warning
Trigger an audible beep when an alarm is detected.
Notify Surveillance Center
Sends an exception or alarm signal to remote alarm host when an event occurs. The alarm host refers to the
PC installed with Remote Client.
Note: The alarm signal will be transmitted automatically at detection mode when remote alarm host is
configured. Please refer to Chapter 8.2.5 for details of alarm host configuration.
Send Email
Send an email with alarm information to a user or users when an alarm event is detected.
Please refer to Chapter 8.2.9 for details of Email configuration.
89
User Manual of DS-7100HWI/HVI-SL Series DVR
CHAPTER8
Network Settings
90
User Manual of DS-7100HWI/HVI-SL Series DVR
8.1 Configuring General Settings
Purpose:
Network settings must be properly configured before you operate device over network.
Steps:
1. Enter the Network Settings interface.
Menu > Configuration > Network
Figure 8.1 General Network Settings Interface
2. Select the General tab.
3. In the General Settings interface:
You can configure the following settings: NIC Type, IPv4 Address, IPv4 Gateway, MTU and DNS
Server.
If the DHCP server is available, you can click the checkbox of DHCP to automatically obtain an IP
address and other network settings from that server.
Note: The valid value range of MTU is 1280 ~ 1500.
4. After having configured the general settings, click the Apply button to save the settings.
8.2 Configuring Advanced Settings
8.2.1 Configuring PPPoE Settings
Purpose:
Your device also allows access by Point-to-Point Protocol over Ethernet (PPPoE).
Steps:
1.
Enter the Network Settings interface.
Menu > Configuration > Network
2.
Select the PPPoE tab to enter the PPPoE Settings interface.
91
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 8.2 PPPoE Settings Interface
3.
Check the PPPoE checkbox to enable this feature.
4.
Enter User Name and Password for PPPoE access.
Note: The User Name and Password should be assigned by your ISP.
Figure 8.3 PPPoE Settings Interface
5.
Click the Apply button to save and exit the interface.
6.
After successful settings, the system asks you to reboot the device to enable the new settings, and the
PPPoE dial-up is automatically connected after reboot.
You can go to Menu>Maintenance>System Info>Network interface to view the status of PPPoE
connection. Please refer to Chapter 11.1Viewing System Information for PPPoE status.
8.2.2 Configuring DDNS
Purpose:
If your device is set to use PPPoE as its default network connection, you may set Dynamic DNS (DDNS) to
be used for network access.
Prior registration with your ISP is required before configuring the system to use DDNS.
Steps:
1.
Enter the Network Settings interface.
Menu > Configuration > Network
2.
Select the DDNS tab to enter the DDNS Settings interface.
Figure 8.4 DDNS Settings Interface
3.
Check the DDNS checkbox to enable this feature.
4.
Select DDNS Type. Five different DDNS types are selectable: IPServer, DynDNS, PeanutHull,
NO-IP and hkDDNS.
• IPServer: Enter Server Address for IPServer.
Note: The Server Address should be the IP address of the PC that runs IPServer.
92
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 8.5 IPServer Settings Interface
• DynDNS:
1) Enter Server Address for DynDNS (e.g. members.dyndns.org).
2) In the Device Domain Name text field, enter the domain obtained from the DynDNS
website.
3) Enter the User Name and Password registered in the DynDNS website.
Figure 8.6 DynDNS Settings Interface
• PeanutHull: Enter User Name and Password obtained from the PeanutHull website.
Figure 8.7 Peanut Hull Settings Interface
• NO-IP:
Enter the account information in the corresponding fields. Refer to the DynDNS settings.
1) Enter Server Address for NO-IP.
2) In the Device Domain Name text field, enter the domain obtained from the NO-IP website
(www.no-ip.com).
3) Enter the User Name and Password registered in the NO-IP website.
93
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 8.8 NO-IP Settings Interface
• hkDDNS: You need to enter the Server Address and Device Domain Name for hkDDNS, and
other fields are read only.
1) Enter the Server Address of the hkDDNS server: www.hiddns.com.
2) Enter the Device Domain Name. You can register the alias of the device domain name in
the hkDDNS server first and then enter the alias to the Device Domain Name in the DVR;
you can also enter the domain name directly on the DVR to create a new one.
Note: If a new alias of the device domain name is defined in the DVR, it will replace the old
one registered on the server.
Figure 8.9 hkDDNS Settings Interface
Register the device on the hkDDNS server.
1)
Go to the hkDDNS website: www.hiddns.com.
2)
Click
3)
After registration is successful, use the account and password to log in.
to register a user account if you do not have one.
Figure 8.10 Register an Account
4)
In the DDNS Management System interface, click the Device Management tab on the
left menu bar and then click
to register the device.
94
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 8.11 Register the Device
Note: Only lower-case English alphabet, numeric and ‘-’ can be used in the alias of the device and the
alias must be started with letters of the lower-case English alphabet.
5.
Click the Apply button to save and exit the interface.
8.2.3 Configuring NTP Server
Purpose:
A Network Time Protocol (NTP) Server can be configured on your device to ensure the accuracy of system
date/time.
Steps:
1.
Enter the Network Settings interface.
Menu > Configuration > Network
2.
Select the NTP tab to enter the NTP Settings interface.
Figure 8.12 NTP Settings Interface
3.
Check the Enable NTP checkbox to enable this feature.
4.
Configure the following NTP settings:
• Interval: Time interval between the two synchronizing actions with NTP server. The unit is minute.
• NTP Server: IP address of NTP server.
• NTP Port: Port of NTP server.
5.
Click the Apply button to save and exit the interface.
Note: The time synchronization interval can be set from 1 to 10080min, and the default value is 60min. If the
device is connected to a public network, you should use a NTP server that has a time synchronization function,
such as the server at the National Time Center (IP Address: 210.72.145.44). If the device is setup in a more
customized network, NTP software can be used to establish a NTP server used for time synchronization.
8.2.4 Configuring UPnP™
Purpose:
95
User Manual of DS-7100HWI/HVI-SL Series DVR
UPnP™ can permits the device seamlessly discover the presence of other network devices on the network and
establish functional network services for data sharing, communications, etc. If you want to use the UPnP™
function to enable the fast connection of the device to the WAN via a router, you should configure the UPnP™
parameters of the device.
Before you start:
If you want to enable the UPnP™ function of the device, you must enable the UPnP™ function of the router
to which your device is connected. When the network working mode of the device is set as multi-address, the
Default Route of the device should be in the same network segment as that of the LAN IP address of the
router.
Steps:
1. Enter the Network Settings interface.
Menu > Configuration > Network
2. Select the UPnP tab to enter the UPnP™ interface.
Figure 8.13 UPnP™ Settings Interface
3. Check
checkbox to enable UPnP™.
4. Select the mapped type to Auto or Manual.
When you select Auto, the mapping ports can be automatically assigned by the router. When you select
Manual, you should continue Step5 to edit the mapping ports.
5. Click
to open the External Port Settings dialog box. Configure the external port No. for server port,
HTTP port and RTSP port respectively.
Notes:
1)
You can use the default port No., or change it according to actual requirements.
2)
External Port indicates the port No. for port mapping in the router.
Figure 8.14 External Port Settings Dialog Box
6. You can click Refresh to get the latest status of the port mapping.
96
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 8.15 UPnP™ Settings Finished
7. Click the Apply button to save the settings.
8.2.5 Configuring Remote Alarm Host
Purpose:
With a remote alarm host configured, the device will send the alarm event or exception message to the host
when an alarm is triggered. The remote alarm host must have the CMS (Client Management System) software
installed.
Steps:
1.
Enter the Network Settings interface.
Menu > Configuration > Network
2.
Select the More Settings tab to enter the More Settings interface.
Figure 8.16 More Settings Interface
3.
Enter Alarm Host IP and Alarm Host Port in the text fields.
The Alarm Host IP refers to the IP address of the remote PC on which the CMS (Client Management
System) software (e.g., iVMS-4200) is installed, and the Alarm Host Port must be the same as the
alarm monitoring port configured in the software (default port is 7200).
Figure 8.17 Configure Alarm Host
97
User Manual of DS-7100HWI/HVI-SL Series DVR
4.
Click the Apply button to save and exit the interface.
8.2.6 Configuring Multicast
Purpose:
The multicast can be configured to realize live view for more than the maximum number of cameras through
network.
A multicast address spans the Class-D IP range of 224.0.0.0 to 239.255.255.255. It is recommended to use the
IP address ranging from 239.252.0.0 to 239.255.255.255.
Steps:
1.
Enter the Network Settings interface.
Menu > Configuration > Network
2.
Select the More Settings tab to enter the More Settings interface.
3.
Set Multicast IP. When adding a device to the CMS (Client Management System) software, the
multicast address must be the same as the device’s multicast IP.
Figure 8.18 Configure Multicast
4.
Click the Apply button to save and exit the interface.
8.2.7 Configuring RTSP
Purpose:
The RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in entertainment and
communications systems to control streaming media servers.
Steps:
1.
Enter the Network Settings menu by clicking Menu > Configuration > Network.
2.
Select the More Settings tab to enter the More Settings men.
Figure 8.19 RTSP Settings Interface
3.
Enter the RTSP port in the text field of RTSP Service Port. The default RTSP port is 554, and you
can change it according to different requirements.
98
User Manual of DS-7100HWI/HVI-SL Series DVR
4.
Click the Apply button to save and exit the menu.
8.2.8 Configuring Server and HTTP Ports
Purpose:
You can change the server and HTTP ports in the Network Settings menu. The default server port is 8000 and
the default HTTP port is 80.
Steps:
1.
Enter the Network Settings interface.
Menu > Configuration > Network
2.
Select the More Settings tab to enter the More Settings interface.
3.
Enter new Server Port and HTTP Port.
Figure 8.20 Host/Others Settings Menu
4.
Enter the Server Port and HTTP Port in the text fields. The default Server Port is 8000 and the HTTP
Port is 80, and you can change them according to different requirements.
5.
Click the Apply button to save and exit the interface.
Note: The Server Port should be set to the range of 2000-65535 and it is used for remote client software
access. The HTTP port is used for remote IE access.
8.2.9 Configuring Email
Purpose:
The system can be configured to send an Email notification to all designated users if an alarm event is
detected, a motion detection event is detected, etc.
Before configuring the Email settings, the device must be connected to a local area network (LAN) that
maintains an SMTP mail server. The network must also be connected to either an intranet or the Internet
depending on the location of the e-mail accounts to which you want to send notification.
Steps:
1.
Enter the Network Settings interface.
Menu > Configuration > Network
2.
Set the IPv4 Address, IPv4 Subnet Mask, IPv4 Gateway and the Preferred DNS Server in the Network
Settings menu.
99
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 8.21 Network Settings Interface
3.
Click the Apply button to save the settings.
4.
Select the Email tab to enter the Email Settings interface.
Figure 8.22 Email Settings Interface
5.
Configure the following Email settings:
Enable Server Authentication (optional): Check the checkbox to enable the server
authentication feature.
User Name: The user account of sender’s Email for SMTP server authentication.
Password: The password of sender’s Email for SMTP server authentication.
SMTP Server: The SMTP Server IP address or host name (e.g., smtp.263xmail.com).
SMTP Port: The SMTP port. The default TCP/IP port used for SMTP is 25.
Enable SSL (optional): Click the checkbox to enable SSL if required by the SMTP server.
Sender: The name of sender.
Sender’s Address: The Email address of sender.
Select Receivers: Select the receiver. Up to 3 receivers can be configured.
Receiver: The name of user to be notified.
Receiver’s Address: The Email address of user to be notified.
Enable Attached Pictures: Check the checkbox of Enable Attached Picture if you want to send
email with attached alarm images.
100
User Manual of DS-7100HWI/HVI-SL Series DVR
Interval: The interval refers to the time between two actions of sending attached pictures.
Figure 8.23 Configure Email Settings
6.
Click the Apply button to save the Email settings.
7.
You can click the Test button to test whether your Email settings work. The corresponding Attention
message box will pop up.
Figure 8.24 Email Testing Attention
101
User Manual of DS-7100HWI/HVI-SL Series DVR
8.3 Checking Network Traffic
Purpose:
You can check the network traffic to obtain real-time information of device such as linking status, MTU,
sending/receiving rate, etc.
Steps:
1.
Enter the Network Traffic interface.
Menu > Maintenance > Net Detect
Figure 8.25 Network Traffic Interface
2.
You can view the sending rate and receiving rate information on the interface. The traffic data is
refreshed every 1 second.
102
User Manual of DS-7100HWI/HVI-SL Series DVR
8.4 Network Detection
Purpose:
You can obtain network connecting status of device through the network detection function, including network
delay, packet loss, etc.
8.4.1 Testing Network Delay and Packet Loss
Steps:
1.
Enter the Network Traffic interface.
Menu > Maintenance > Net Detect
2.
Click the Network Detection tab to enter the Network Detection menu.
Figure 8.26 Network Detection Interface
3.
Enter the destination address in the text field of Destination Address.
4.
Click the Test button to start testing network delay and packet loss. The testing result pops up on the
window. If the testing is failed, the error message box will pop up as well.
.
Figure 8.27 Testing Result of Network Delay and Packet Loss
8.4.2 Exporting Network Packet
Purpose:
By connecting the device to network, the captured network data packet can be exported to USB-flash disk and
other local backup devices.
Steps:
1. Enter the Network Traffic interface.
Menu > Maintenance > Net Detect
2. Click the Network Detection tab to enter the Network Detection interface.
103
User Manual of DS-7100HWI/HVI-SL Series DVR
3. Select the backup device from the dropdown list of Device Name, as shown in Figure 8.28.
Note: Click the Refresh button if the connected local backup device cannot be displayed. When it fails
to detect the backup device, please check whether it is compatible with the device. You can format the
backup device if the format is incorrect.
Figure 8.28 Export Network Packet
4. Click the Export button to start exporting.
5. After the exporting is complete, click OK to finish the packet export.
Figure 8.29 Packet Export Attention
Note: Up to 1M data can be exported each time.
104
User Manual of DS-7100HWI/HVI-SL Series DVR
8.4.3 Checking Network Status
Purpose:
You can also check the network status and quick set the network parameters in this interface.
Steps:
Click Status on the right bottom of the page.
Figure 8.30 Checking Network Status
If the network is normal the following message box pops out.
Figure 8.31 Network Status Checking Result
If the message box pops out with other information instead of this one, you can click Network button to show
the quick setting interface of the network parameters.
105
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 8.32 Network Parameters Configuration
8.4.4 Checking Network Statistics
Purpose:
You can check the network statistics to obtain the real-time information of the device.
Steps:
1. Enter the Network Statistics interface.
Menu > Maintenance> Net Detect
2. Click the Network Stat. tab to enter the Network Statistics menu.
Figure 8.33 Network Stat. Interface
3. View the bandwidth of Remote Live View, bandwidth of Remote Playback, bandwidth of Net Total Idle
information.
4. Click Refresh button to get the latest bandwidth statistics.
106
User Manual of DS-7100HWI/HVI-SL Series DVR
CHAPTER9
HDD Management
107
User Manual of DS-7100HWI/HVI-SL Series DVR
9.1 Initializing HDDs
Purpose:
A newly installed hard disk drive (HDD) must be initialized before it can be used with your device.
Steps:
1.
Enter the HDD Information interface.
Menu > HDD>General
Figure 9.1 HDD Information Interface
2.
Select the HDD to be initialized.
3.
Click the Init button.
Figure 9.2 Confirm Initialization
4.
Select the OK button to start initialization.
108
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 9.3 Start Initialization
5.
After the HDD has been initialized, the status of the HDD will change from Uninitialized to Normal.
Figure 9.4 HDD Status Changes to Normal
Note: Initializing the HDD will erase all data on it.
9.2 Configuring Quota Mode
Purpose
Each camera can be configured with allocated quota for the storage of recorded files.
Steps
1.
Enter the Storage Mode interface.
2.
Set the Mode to Quota.
Menu > HDD > Advanced
Note: The device must be rebooted to activate the settings.
Figure 9.5 Storage Mode Settings Interface
3.
Enter the storage capacity in the text field of Max. Record Capacity (GB).
109
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 9.6 Configure Record Quota
4.
You can copy the quota settings of the current camera to other cameras if required. Click the Copy button
to enter the Copy Camera menu, as shown below.
Figure 9.7 Copy Settings to Other Camera(s)
5.
Select the camera (s) to be configured with the same quota settings. You can also click the checkbox of
Analog to select all cameras.
6.
Click the OK button to finish the Copy settings and back to the Storage Mode interface.
7.
Click the Apply button to apply the settings.
Note: If the quota capacity is set to 0, then all cameras will use the total capacity of HDD for recording.
110
User Manual of DS-7100HWI/HVI-SL Series DVR
9.3 Checking HDD Status
Purpose:
You may check the status of the installed HDD on device so as to take immediate check and maintenance in case
of HDD failure.
Checking HDD Status in HDD Information Interface
Steps:
1.
Enter the HDD Information interface.
Menu > HDD>General
2.
Check the status of each HDD which is displayed on the list.
Figure 9.8 View HDD Status (1)
Note: If the status of HDD is Normal or Sleeping, it works normally. If the status is Uninitialized or Abnormal,
please initialize the HDD before use. And if the HDD initialization is failed, please replace it with a new one.
Checking HDD Status in HDD Information Interface
Steps:
1.
Enter the System Information interface.
2.
Click the HDD tab to view the status of HDD displayed on the list.
Menu > Maintenance > System Info
Figure 9.9 View HDD Status (2)
111
User Manual of DS-7100HWI/HVI-SL Series DVR
9.4 Checking S.M.A.R.T. Information
Purpose:
The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system for HDD to detect
and report on various indicators of reliability in the hopes of anticipating failures.
Steps:
1.
Enter the S.M.A.R.T. Settings interface.
Menu > HDD >HDD Detect >S.M.A.R.T. Settings
2.
Select the HDD to view its S.M.A.R.T. information list.
Note: If you want to use the HDD even when the S.M.A.R.T. checking is failed, you can check the
checkbox before the Continue to use this disk when self-evaluation is failed item.
3.
Three self-tests of S.M.A.R.T are provided, including Short Test, Expanded Test and Conveyance Test.
You can select a self-test type and click
to start self-test.
Figure 9.10 S.M.A.R.T. Settings Interface
112
User Manual of DS-7100HWI/HVI-SL Series DVR
9.5 Detecting Bad Sector
Purpose:
The bad sectors of a HDD may cause the system to slow down when reading or writing data. You can detect the
bad sectors of the HDD and thus to take immediate measures to repair it.
Steps:
1. Enter the Bad Sector Detection interface.
Menu>HDD>HDD Detect>Bad Sector Detection
Figure 9.11 Bad Sector Detection
2. Click Detect to start detecting.
Figure 9.12 Bad Sector Detecting
3. You can click Pause to pause the detection and click Resume to resume the detection.
4. If there is any error information about the HDD, you can click Error info to view the information.
113
User Manual of DS-7100HWI/HVI-SL Series DVR
9.6 Configuring HDD Error Alarms
Purpose:
You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal.
Steps:
1.
Enter the Exception interface.
Menu > Configuration > Exceptions
2.
Select the Exception Type to HDD Error from the dropdown list.
3.
Click the checkbox(s) below to select the HDD error alarm type (s).
Note: The alarm type can be selected to: Audio Warning, Notify Surveillance Center, and Send Email. Please
refer to Chapter 7.5 Setting Alarm Response Actions.
Figure 9.13 Configure HDD Error Alarm
4.
Click the Apply button to save the settings.
114
User Manual of DS-7100HWI/HVI-SL Series DVR
C H A P T E R 10
Camera Settings
115
User Manual of DS-7100HWI/HVI-SL Series DVR
10.1 Configuring OSD Settings
Purpose:
You can configure the OSD (On-screen Display) settings for the camera, including date /time, camera name, etc.
Steps:
1. Enter the OSD Configuration interface.
Menu > Camera > OSD
2. Select the camera to configure OSD settings.
3. Edit the Camera Name in the text field.
4. Configure the Display Name, Display Date and Display Week by clicking the checkbox.
5. Select the Date Format, Time Format and Display Mode.
Figure 10.1 OSD Configuration Interface
6. You can use the mouse to click and drag the text frame on the preview window to adjust the OSD position.
7. Copy Camera Settings
1)
If you want to copy the OSD settings of the current camera to other cameras, click the Copy button to
enter the Copy Camera interface.
Figure 10.2 Copy Settings to Other Cameras
2)
Select the camera (s) to be configured with the same OSD settings. You can also click the checkbox of
Analog to select all cameras.
3)
Click the OK button to finish the Copy settings and back to the OSD Configuration interface.
8. Click the Apply button to apply the settings.
Note: You can also click the Restore to restore the current OSD settings to the default parameters.
116
User Manual of DS-7100HWI/HVI-SL Series DVR
10.2 Configuring Privacy Mask
Purpose:
You are allowed to configure the four-sided privacy mask zones that cannot be viewed by the operator.
Steps:
1. Enter the Privacy Mask Settings interface.
Menu > Camera > Privacy Mask
2. Select the camera to set privacy mask.
3. Click the checkbox of Enable Privacy Mask to enable this feature.
Figure 10.3 Privacy Mask Settings Interface
4. Use the mouse to draw a zone on the window. The zones will be marked with different frame colors.
Note: Up to 4 privacy mask zones can be configured, and the size of each area can be adjusted.
5. The configured privacy mask zones on the window can be cleared by clicking the corresponding Clear
Zone1-4 icons on the right side of the window, or click Clear All to clear all zones.
Figure 10.4 Set Privacy Mask Area
6. You can click the Copy button to copy the privacy mask settings of the current camera to other cameras.
Please refer to step 7 of Chapter 10.1 Configuring OSD Settings.
7. Click the Apply button to save the settings.
Note: You can also click the Restore to restore the current OSD settings to the default parameters.
117
User Manual of DS-7100HWI/HVI-SL Series DVR
10.3 Configuring Video Parameters
Steps:
1. Enter the Image Settings interface.
Menu > Camera > Image
2. Select the camera to set image parameters.
3. Set the period of a day for configuring independent image parameters so as to satisfy different light
conditions, e.g., daylight and night time. Two periods can be configured. When you have configured Period 1,
the Period 2 is remained as the Other Time.
Figure 10.5 Image Settings Interface
4. Select the mode from the drop-down menu according to different light conditions.
Four modes are selectable:

Standard: in general lighting conditions (default).

Indoor: the image is relatively smoother.

Dim Light: the image is smoother than the other three modes.

Outdoor: the image is relatively clearer and sharper. The degree of contrast and saturation is high.
5. Adjust the image parameters including the brightness, contrast, saturation, hue, sharpness and denoising level
by moving the sliding bar or increasing/decreasing the value.
Note: When you select different mode, corresponding default parameters are available. You can also adjust
the value of the brightness, contrast, saturation and hue to 0~ 255, the sharpness to 0~ 15 and the denoising
level to 0~ 5.
6. You can click the Copy button to copy the image settings of the current camera to other cameras. Please
refer to step 7 of Chapter 10.1 Configuring OSD Settings.
7. On the Image Settings interface, click the Apply button to save the settings.
Note: you can click the Restore button to restore the current image settings to default parameters.
118
User Manual of DS-7100HWI/HVI-SL Series DVR
CHAPTER11
Device Management and Maintenance
119
User Manual of DS-7100HWI/HVI-SL Series DVR
11.1 Viewing System Information
11.1.1 Viewing Device Information
Steps:
1. Enter the System Information interface.
Menu > Maintenance > System Info
2. Click the Device Info tab to enter the Device Information menu to view the device name, model, serial No. ,
firmware version and encoding version.
Figure 11.1 Device Information Interface
11.1.2 Viewing Camera Information
Steps:
1.
Enter the System Information interface.
2.
Click the Camera tab to enter the Camera Information menu to view the status of each camera.
Menu > Maintenance > System Info
Figure 11.2 Camera Information Interface
11.1.3 Viewing Record Information
Steps:
1. Enter the System Information interface.
Menu > Maintenance > System Info
2. Click the Record tab to enter the Record Information menu to view the recording status and encoding
120
User Manual of DS-7100HWI/HVI-SL Series DVR
parameters of each camera.
Figure 11.3 Record Information Interface
11.1.4 Viewing Network Information
Steps:
1. Enter the System Information interface.
Menu > Maintenance > System Info
2. Click the Network tab to enter the Network Information menu to view the network information.
Figure 11.4 Network Information Interface
11.1.5 Viewing HDD Information
Steps:
1. Enter the System Information interface.
Menu > Maintenance > System Info
121
User Manual of DS-7100HWI/HVI-SL Series DVR
2. Click the HDD tab to enter the HDD Information menu to view the HDD status, free space, property, etc.
Figure 11.5 HDD Information Interface
122
User Manual of DS-7100HWI/HVI-SL Series DVR
11.2 Searching & Exporting Log Files
Purpose:
The operation, alarm, exception and information of the device can be stored in log files, which can be viewed and
exported at any time.
Steps:
1. Enter the Log Search interface.
Menu > Maintenance > Log Information
Figure 11.6 Log Search Interface
2. Set the log search conditions to refine your search, including the Start Time, End Time, Major Type and
Minor Type.
3. Click the Search button to start searching log files.
4. The matched log files will be displayed on the list shown below.
Note: Up to 2000 log files can be displayed each time.
Figure 11.7 Log Search Results
5. You can click the
click the
button of each log or double click it to view its detailed information. And you can also
button to view the related video files if available.
123
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 11.8 Log Details
6. If you want to export the log files, click the Export button to enter the Export menu.
You can also export all the log files stored in the HDD.
(1)
Enter the Log Export interface.
Menu > Maintenance > Log Information>Log Export
Figure 11.9 Log Export Interface
(2)
Check
checkbox to select the HDD and click Export to enter the export interface.
124
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 11.10 Export Log Files
7. Select the backup device from the dropdown list of Device Name.
8. Click the Export to export the log files to the selected backup device.
You can click the New Folder button to create new folder in the backup device, or click the Format button
to format the backup device before log export.
Notes:
1) Please connect the backup device to device before operating log export.
2) The log files exported to the backup device are named by exporting time, e.g.,
20110514124841logBack.txt.
11.3 Importing/Exporting Configuration Files
Purpose:
The configuration files of the device can be exported to local device for backup; and the configuration files of one
device can be imported to multiple device devices if they are to be configured with the same parameters.
Steps:
1. Enter the Import/Export Configuration File interface.
Menu > Maintenance > Import/Export
125
User Manual of DS-7100HWI/HVI-SL Series DVR
Figure 11.11 Import/Export Config File
2. Click the Export button to export configuration files to the selected local backup device.
3. To import a configuration file, select the file from the selected backup device and click the Import button.
After the import process is completed, you must reboot the device.
Note: After having finished the import of configuration files, the device will reboot automatically.
126
User Manual of DS-7100HWI/HVI-SL Series DVR
11.4 Upgrading System
Purpose:
The firmware on your device can be upgraded by local backup device or remote FTP server.
11.4.1 Upgrading by Local Backup Device
Steps:
1. Connect your device with a local backup device where the update firmware file is located.
2. Enter the Upgrade interface.
Menu > Maintenance > Upgrade
3. Click the Local Upgrade tab to enter the local upgrade menu.
Figure 11.12 Local Upgrade Interface
4. Select the update file from the backup device.
5. Click the Upgrade button to start upgrading.
6. After the upgrading is complete, reboot the device to activate the new firmware.
11.4.2 Upgrading by FTP
Before you start:
Configure PC (running FTP server) and device to the same Local Area Network. Run the 3rd-party TFTP software
on the PC and copy the firmware into the root directory of TFTP.
Steps:
1. Enter the Upgrade interface.
Menu > Maintenance > Upgrade
2. Click the FTP tab to enter the local upgrade interface.
Figure 11.13 FTP Upgrade Interface
127
User Manual of DS-7100HWI/HVI-SL Series DVR
3. Enter the FTP Server Address in the text field.
4. Click the Upgrade button to start upgrading.
5. After the upgrading is complete, reboot the device to activate the new firmware.
128
User Manual of DS-7100HWI/HVI-SL Series DVR
11.5 Restoring Default Settings
Steps:
1.
Enter the Default interface.
Menu > Maintenance > Default
Figure 11.14 Restore Factory Default
2.
Click the OK button to restore the default settings.
Note: Except the network parameters (including IP address, subnet mask, gateway, MTU and server port), all other
parameters of the device will be restored to factory default settings.
129
User Manual of DS-7100HWI/HVI-SL Series DVR
CHAPTER12
Others
130
User Manual of DS-7100HWI/HVI-SL Series DVR
12.1 Configuring General Settings
Purpose:
You can configure the BNC output standard, VGA output resolution, mouse pointer speed, etc.
Steps:
1.
Enter the General Settings interface.
Menu > Configuration > General
2.
Select the General tab.
Figure 12.1 General Settings Interface
3.
Configure the following settings:
• Language: The default language used is English.
• CVBS Output Standard: Select the CVBS output standard to NTSC or PAL, which must be the
same with the video input standard.
• Resolution: Select the VGA output resolution, which must be the same with the resolution of the
monitor screen.
•
•
•
•
•
•
•
4.
Time Zone: Select the time zone.
Date Format: Set the date format.
System Date: Select the system date.
System Time: Set the system time.
Mouse Pointer Speed: Set the speed of mouse pointer; 4 levels are configurable.
Enable Wizard: Enable/disable the Wizard when the device starts up.
Enable ID Authentication: Enable/disable the use of the login password.
Click the Apply button to save the settings.
131
User Manual of DS-7100HWI/HVI-SL Series DVR
12.2 Configuring DST Settings
Steps:
1.
Enter the General Settings interface.
Menu >Configuration>General
2.
Choose DST Settings tab.
Figure 12.2 DST Settings Interface
You can check the checkbox before the Auto DST Adjustment item.
Or you can manually check the Enable DST checkbox, and then set the date of the DST period.
132
User Manual of DS-7100HWI/HVI-SL Series DVR
12.3 Configuring More Settings
Steps:
1.
Enter the General Settings interface.
Menu > Configuration > General
2.
Click the More Settings tab to enter the More Settings interface.
Figure 12.3 More Settings Interface
3.
Configure the following settings:
• Device Name: Edit the name of device.
• Device No.: Edit the serial number of device. The Device No. can be set in the range of 1~255, and
the default No. is 255.
• CVBS Output Brightness: Adjust the video output brightness.
• Operation Timeout: Set timeout time for menu inactivity. E.g., when the timeout time is set to 5
Minutes, the system will exit from the current operation menu to live view screen after 5 minutes
of menu inactivity.
• Menu Output Mode: Select the menu output mode to Auto, VGA or Main CVBS.
Notes:
1. When you select Auto, the device can automatically detect the VGA output as the main output
and the CVBS output as the auxiliary output when it starts up.
2. After you have changed the output mode, you should restart the device to activate the new
settings.
4.
Click the Apply button to save the settings.
133
User Manual of DS-7100HWI/HVI-SL Series DVR
12.4 Managing User Accounts
Purpose:
There is a default account in the device: Administrator. The Administrator user name is admin and the password is
12345. The Administrator has the permission to add and delete user and configure user parameters.
12.4.1 Adding a User
Steps:
1.
Enter the User Management interface.
Menu > Configuration > User
Figure 12.4 User Management Interface
2.
Click the Add button to enter the Add User interface.
Figure 12.5 Add User Menu
3.
Enter the information for new user, including User Name, Password, Level and User’s MAC Address.
Level: Set the user level to Operator or Guest. Different user levels have different operating permission.
134
User Manual of DS-7100HWI/HVI-SL Series DVR
• Operator: The Operator user level has permission of Local Log Search in Local Configuration,
Remote Log Search and Two-way Audio in Remote Configuration and all operating permission in
Camera Configuration.
• Guest: The Guest user has permission of Local Log Search in Local Configuration, Remote Log
Search in Remote Configuration and only has the local/remote playback in the Camera Configuration.
User’s MAC Address: The MAC address of the remote PC which logs onto the device. If it is configured
and enabled, it only allows the remote user with this MAC address to access the device.
4.
Click the OK button to save the settings and go back to the User Management interface. The added new
user will be displayed on the list.
Figure 12.6 Added User Listed in User Management Interface
5.
Select the user from the list and then click the
button to enter the Permission settings interface.
Figure 12.7 User Permission Settings Interface
6.
Set the operating permission of Local Configuration, Remote Configuration and Camera Configuration for
the user.
Local Configuration
• Local Log Search: Searching and viewing logs and system information of device.
• Local Parameters Settings: Configuring parameters, restoring factory default parameters and
importing/exporting configuration files.
• Local Advanced Operation: Operating HDD management (initializing HDD, setting HDD
135
User Manual of DS-7100HWI/HVI-SL Series DVR
property), upgrading system firmware.
• Local Shutdown /Reboot: Shutting down or rebooting the device.
Remote Configuration
• Remote Log Search: Remotely viewing logs that are saved on the device.
• Remote Parameters Settings: Remotely configuring parameters, restoring factory default
parameters and importing/exporting configuration files.
• Two-Way Audio: Realizing two-way radio between the remote client and the device.
• Remote Advanced Operation: Remotely operating HDD management (initializing HDD),
upgrading system firmware.
• Remote Alarm Control: Remotely arming (notify alarm and exception message to the remote
client).
• Remote Shutdown/Reboot: Remotely shutting down or rebooting the device.
Camera Configuration
• Remote Live View: Remotely viewing live video of the selected camera (s).
• Local Manual Operation: Locally starting/stopping manual recording of the selected camera (s).
• Remote Manual Operation: Remotely starting/stopping manual recording of the selected camera
(s).
• Local Playback: Locally playing back recorded files of the selected camera (s).
• Remote Playback: Remotely playing back recorded files of the selected camera (s).
• Local Video Export: Locally exporting recorded files of the selected camera (s).
Note: You should select the camera (s) on the Camera Configuration interface for the operation
permission configured.
7.
Click the OK button to save the settings and exit interface.
Note: Only the admin user account has the permission of restoring factory default parameters.
12.4.2 Deleting a User
Steps:
1.
Enter the User Management interface.
Menu > Configuration > User
2.
Select the user to be deleted from the list.
Figure 12.8 Delete a User
3.
Click the
icon to delete the selected user.
136
User Manual of DS-7100HWI/HVI-SL Series DVR
12.4.3 Editing a User
Steps:
1.
Enter the User Management interface.
Menu > Configuration > User
2.
Select the user to be edited from the list.
Figure 12.9 Edit a User
3.
Click the
icon to enter the Edit User interface.
Figure 12.10 Edit User Interface
4.
Edit the user information, including user name, password, level and MAC address.
5.
Click the OK button to save the settings and exit the menu.
12.4.4 Changing Password of Admin
Purpose:
The password of the admin user account can be changed in the User Management menu.
137
User Manual of DS-7100HWI/HVI-SL Series DVR
Steps:
1.
Enter the User Management interface.
Menu > Configuration > User
Figure 12.11 Change Password
2.
Select the admin user and click
to change the password.
Figure 12.12 Change Password
3.
Enter the old password, check
checkbox, enter new password and confirm password on the menu.
4.
Click OK to save the settings and exit the menu.
138
User Manual of DS-7100HWI/HVI-SL Series DVR
12.5 Logging out/Shutting down/Rebooting
Device
Steps:
1. Enter the Shutdown interface.
Menu > Shutdown
Figure 12.13 Shutdown Menu
2. Click the Logout button to log out, or
Click the Shutdown button to shut down the device, or
Click the Reboot button to reboot the device.
Note: After you have logged out the system, menu operation on the screen is invalid. It is required a user name and
password to login the system.
139
User Manual of DS-7100HWI/HVI-SL Series DVR
CHAPTER14
Appendix
140
User Manual of DS-7100HWI/HVI-SL Series DVR
Glossary
• Dual Stream: Dual stream is a technology used to record high resolution video locally while transmitting
a lower resolution stream over the network. The two streams are generated by the device, with the main
stream having a maximum resolution of 4CIF and the sub-stream having a maximum resolution of CIF.
• DVR: Acronym for Digital Video Recorder. A DVR is device that is able to accept video signals from
analog cameras, compress the signal and store it on its hard drives.
• HDD: Acronym for Hard Disk Drive. A storage medium which stores digitally encoded data on platters
with magnetic surfaces.
• DHCP: Dynamic Host Configuration Protocol (DHCP) is a network application protocol used by devices
(DHCP clients) to obtain configuration information for operation in an Internet Protocol network.
• HTTP: Acronym for Hypertext Transfer Protocol. A protocol to transfer hypertext request and information
between servers and browsers over a network
• PPPoE: PPPoE, Point-to-Point Protocol over Ethernet, is a network protocol for encapsulating
Point-to-Point Protocol (PPP) frames inside Ethernet frames. It is used mainly with ADSL services where
individual users connect to the ADSL transceiver (modem) over Ethernet and in plain Metro Ethernet
networks.
• DDNS: Dynamic DNS is a method, protocol, or network service that provides the capability for a
networked device, such as a router or computer system using the Internet Protocol Suite, to notify a
domain name server to change, in real time (ad-hoc) the active DNS configuration of its configured
hostnames, addresses or other information stored in DNS.
• Hybrid DVR: A hybrid DVR is a combination of a DVR and NVR.
• NTP: Acronym for Network Time Protocol. A protocol designed to synchronize the clocks of computers
over a network.
• NTSC: Acronym for National Television System Committee. NTSC is an analog television standard used
in such countries as the United States and Japan. Each frame of an NTSC signal contains 525 scan lines at
60Hz.
• NVR: Acronym for Network Video Recorder. An NVR can be a PC-based or embedded system used for
centralized management and storage for IP cameras, IP Domes and other DVRs.
• PAL: Acronym for Phase Alternating Line. PAL is also another video standard used in broadcast
televisions systems in large parts of the world. PAL signal contains 625 scan lines at 50Hz.
• USB: Acronym for Universal Serial Bus. USB is a plug-and-play serial bus standard to interface devices to
a host computer.
141
User Manual of DS-7100HWI/HVI-SL Series DVR
FAQ
• Why does my device make a beeping sound after booting?
The possible reasons for the warning beep on the device are as follows:
a)
There is no HDD installed in the device.
b)
The HDD is not initialized.
c)
HDD error
To cancel the beeping sound and use the device without HDD, enter the Exception Settings interface. For detailed
information, see Chapter 7.4 Handling Exception.
• Why is there no video recorded after setting the motion detection?
If there are no recorded video after setting the motion detection, please check:
a) The recording schedule is set up correctly by following the steps listed in Chapter 4.2 Configuring Record
Schedule.
b) The motion detection area is configured correctly (See Chapter 4.3 Configuring Motion Detection Record).
c) The channels are being triggered for motion detection (See Chapter 4.3 Configuring Motion Detection
Record)).
• Why doesn’t the device detect my USB export device for exporting recorded files?
There’s a chance that the device and your USB device is not compatible. Please refer to our company’s website to
view a list of compatible devices.
• My device is in Live View mode and the menu does not show up. It does not respond to the mouse
operation.
Your device may be in auxiliary mode. Please refer to Chapter 3.2.3 Main/Aux Output Switching for the operation
of main/aux output switching.
142
Open as PDF
Similar pages