Programmable Digital Thermostat with RF Boiler Control

Programmable Digital
Thermostat with RF Boiler Control
Instruction Manual
Model No RT500BC
PRODUCT COMPLIANCE
SALUS Controls Plc hereby declares that the radio equipment type
868Mhz is in compliance with Directives 1999/5/EC, 2014/53/EU,
2006/95/EC, 2004/108/EC, 2011/65/EU, 2009/125/EC and 93/68/
EEC. The full text of the EU declaration of conformity is available at
the following internet address: www.saluslegal.com
SAFETY INFORMATION
These instructions are applicable to the SALUS Controls model stated on the
front cover of this manual only, and must not be used with any other make or
model.
These instructions are intended to apply in the United Kingdom only, and should
be followed along with any other statutory obligations.
This accessory must be fitted by a competent person, and installation must
comply with the guidance provided in the current editions of BS7671 (IEE Wiring
Regulations) and Part ‘P’ of the Building Regulations. Failure to comply with the
requirements of these publications could lead to prosecution.
Always isolate the AC Mains supply before opening or removing the unit
from the wall or wall box.
When fitting batteries don’t mix old and new batteries together. Do not
use rechargeable batteries.
Please leave these instructions with the end user where they should be kept in a
safe place for future reference.
ErP RATING
This product has been rated as: Class 1, Efficiency 1%
2
RT500BC INSTRUCTION MANUAL
What is a programmable room thermostat?
... an explanation for householders
A programmable room thermostat is both a programmer and a room thermostat.
A programmer allows you to set ‘On’ and ‘Off’ time periods to suit your own lifestyle.
A room thermostat works by sensing the air temperature, switching on the heating
when the air temperature falls below the thermostat setting, and switching it off once
this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you want the heating
to be on, and what temperature it should reach while it is on. It will allow you to select
different temperatures in your home at different times of the day (and days of the
week) to meet your particular needs.
Turning a programmable room thermostat to a higher setting will not make the room
heat up any faster. How quickly the room heats up depends on the design of the
heating system, for example, the size of boiler and radiators.
Neither does the setting affect how quickly the room cools down. Turning a
programmable room thermostat to a lower setting will result in the room being
controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to find the lowest
temperature settings that you are comfortable with at the different times you have
chosen, and then leave it alone to do its job. The best way to do this is to set low
temperatures first, say 18°C, and then turn them up by one degree each day until
you are comfortable with the temperatures. You won’t have to adjust the thermostat
further. Any adjustments above these settings will waste energy and cost you more
money.
If your heating system is a boiler with radiators, there will usually be only one
programmable room thermostat to control the whole house. But you can have different
temperatures in individual rooms by installing thermostatic radiator valves (TRVs) on
individual radiators. If you don’t have TRVs, you should choose a temperature that is
reasonable for the whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then prevent any
overheating in other rooms by adjusting the TRVs.
RT500BC INSTRUCTION MANUAL
3
The time on the programmer must be correct. Some types have to be adjusted in
spring and autumn at the changes between Greenwich Mean Time and British Summer
Time.
You may be able to temporarily adjust the heating programme, for example, ‘Override’,
‘Advance’ or ‘Boost’. These are explained in the manufacturer’s instructions.
Programmable room thermostats need a free flow of air to sense the temperature, so
they must not be covered by curtains or blocked by furniture. Nearby electric fires,
televisions, wall or table lamps may prevent the thermostat from working properly.
INTRODUCTION
The RT500 programmable room thermostat from SALUS Controls is a stylish and
accurate 5/2 or 7 day programmable electronic thermostat with a large, easy to
read display. This programmable thermostat has been specifically designed to be
used for both Volt Free and AC heating applications. This programmable thermostat
can replace most common residential thermostats and is designed to be used with
electric, gas or oil heating boilers. Unlike ordinary single unit design thermostats,
this is a new type of thermostat separating the operational functions into two units.
The RF Boiler Control is used for wiring connections and heat on/off control. The
RT500 provides the user interface and temperature sensing / control. The two units
are linked together by a Radio Frequency (RF) signal.
Features
• 5/2 or 7 day programming flexibility
• Built-in start up programming for quick installation
• Large, easy to read display with blue backlight
• Frost protection
• Burner on symbol
• Easy to use programming
• User friendly
4
RT500BC INSTRUCTION MANUAL
INSTALLATION
Please read the important safety information at the start of this manual before you
begin to install the device.
The RT500 programmable room thermostat is easily installed using the Industry
Standard back plate supplied with the unit – this is used purely for mounting
purposes, as no wiring is needed for the RT500. The back plate can be mounted
directly to the wall surface.
The ideal position to locate the RT500 is about 1.5m above floor level. It should be
mounted in a location where the thermostat is accessible, reasonably lit and free from
extremes of temperature and draughts. Do not mount the thermostat on an outside
wall, above a radiator or in a location where it may be subjected to direct sunlight.
To ensure trouble free operation of the Radio Frequency (RF) signal, always ensure
that the programmable thermostat is mounted away from any possible sources of
interference (such as radios, TV sets, computers, etc.), and is not mounted on or in
close proximity to large metal objects. Installing the RT500 in enclosed areas such as
cellars and basements is not recommended.
CONNECTING THE RT500 BOILER CONTROL
NOTE: All electrical installation work should be carried out by a suitably
qualified electrician or other competent person.
If you are not sure how to install the Boiler Control consult either with a qualified
electrician, heating engineer or your boiler / heating system supplier for advice on
how to continue.
INSTALLING THE RF BOILER CONTROL
1. Remove the front panel from the boiler.
2. Pull out the mechanical timer.
3. Do not remove link wire.
4. Connect the electrical plug.
5. Push fit boiler control into housing.
6. Replace the front panel
ensuring a good seal is made.
7. Power up the boiler and check
the correct operation.
RT500BC INSTRUCTION MANUAL
5
RF Boiler Control
LED indicator for learning / output status
Recessed button for ID learning
Max. ambient temperature 55°C
Transmitter link via radio frequency
Current rating 5A (resistive) @ 230V AC
Connections:
1 - Neutral input
2 - Live input
3 - Common input
4 - Normally open output
BOILER CONTROL WIRING TERMINALS
Terminal Identifier Description
1
N Neutral
2
L
3
COM
Linked Live feed
Live feed (230V AC)
4
N.O.
Switched Live (Normally Open [N.O.] contact)
TYPICAL WIRING INSTALLATION
Boiler Control
Boiler
* Do NOT remove link
6
RT500BC INSTRUCTION MANUAL
RT500 THERMOSTAT DEFAULT SETTINGS
Changes to the default settings should only be made by the Engineer
carrying out the installation or other qualified person.
The installer should select the “jumper” positions required if changes
need to be made to the factory default
settings. The “jumpers” are found on the
rear of the RT500.
Jumper
Function
Span
Movable jumper for selecting temperature span
of ± 0.5°C (factory default setting) or ± 1.0°C
1,2,3,4,5
Removable jumpers for altering the RF address
code when used in conjunction with the
teaching mode of the boiler control.
Program
Jumper for 5-2 (factory default setting) or 7
individual days programming.
NOTE: The Reset button must be pressed after changing jumper positions.
RT500BC INSTRUCTION MANUAL
7
CHANGING THE BATTERIES ON THE RT500
1. Open the front flap on the right hand side of the unit, this reveals the SET & SELECT buttons
2. On the bottom right hand side pull the small flap down which will
reveal the batteries as shown above.
3. Remove the old batteries
4. Now insert the new batteries, insert bottom battery with the“+” end
first followed by the top battery “ – “first .
Note:
When changing the batteries the RT500 will save your settings for 10
seconds. After 10 seconds your settings will be lost.
8
RT500BC INSTRUCTION MANUAL
RF ID CODE SETTING
Normally, the RT500 can link with the Boiler Control the ID code setting. If
there is another unit being used nearby, e.g. in the next house, your Boiler
Control may be triggered by the other RT500. You can change the RF ID
Code to help prevent this problem.
Each Boiler Control can only respond to RF transmissions from a RT500
with the same RF ID code setting.
To adjust the RF ID code of the RT500,
remove one or more of the jumper
caps located on the back of the unit
(labelled 1 to 5 as shown in this
picture): Then follow the steps below
to resync the RF communication.
Change ID code settings if you are experiencing communication loss
between the thermostat and the receiver.
RT500BC INSTRUCTION MANUAL
9
SYNCHRONISING THE BOILER CONTROL
(a) RT500 Thermostat
-First change the thermostat RF ID code
by removing one or more of the address
code jumpers as described in page 9.
(Changing from the default RF ID reduces the
risk of error-switching from another
thermostat locally).
- With the Boiler Module LED flashing, press
the thermostat SELECT button for 3 seconds
until ‘10SY’ appears on its screen. (The 10
indicates a 10min countdown whilst
synchronising). Once the receiver LED stops
flashing the synchronisation procedure is
complete. Pressing any button on the
thermostat will return it to normal mode (or
it will time out when the 10mins is expired).
Select
Flashing Red LED
(a) Boiler Module
- Press the sync button on the Boiler Module
for 3 seconds until its red LED starts flashing Sync
(this indicates it’s in sync mode).
(c)
Now test the RF connection as per page 11.
10
RT500BC INSTRUCTION MANUAL
TESTING THE RF TRANSMISSION
It is important to site the RT500 in locations where the RF signal cannot be
interrupted.
The receiving range between the RT500 and the Boiler Control is 70 metres
in open air, however many factors can affect the RF transmission and
shorten the operating distance, e.g. shielding by thick walls, foil backed
plasterboard, metal objects such as filing cabinets, general RF interference,
and so on.
The operating range in most household applications is around 30 metres,
which should be more than adequate in most cases. It is advisable to test
the RF transmission from the intended RT500 location to the Boiler Control
location, particularly if you intend to fix the RT500 to the wall. To check the
RF reception, follow the following steps:
1. Press the UP button on the RT500 programmable room thermostat until
the set point temperature is higher than room temperature by a few
degrees.
2. Wait for a few seconds. The “boiler on” (heat call) indicator
should appear on the bottom left of the display on the RT500.
3. Check the LED (light) on the Boiler control - it should be lit.
4. Press the DOWN button to adjust the set point temperature
to be lower than room temperature.
5. Wait for a few seconds, and the “boiler on” (heat call) indicator should
disappear and the LED (light) on the Boiler Control should switch off.
6. Repeat steps 1 to 5 to make sure the LED (light) on the Boiler Control can
turn on and turn off each time.
If you are unable to get a stable RF connection between the Boiler Control
and RT500, check that the Boiler Control has a mains supply. If this isn’t the
problem you can also alter the RF address code by following the ‘RF ID Code
Setting’ section of this manual, and then repeat steps 1 to 5.
RT500BC INSTRUCTION MANUAL
11
BOILER CONTROL MANUAL OVERRIDE
The AUTO/MANUAL switch allows you to turn on the
Boiler Control manually if required.
SYNC
Button
AUTO MANUAL
When the switch on the Boiler Control is in the AUTO (normal) position, the
Boiler Control will automatically receive the RF signal from the RT500 and
control the boiler based on the programming of the RT500.
The user can also move the switch to the MANUAL position; when in this
mode, the boiler will be always turned on and the LED indicator will also be
lit constantly. The manual mode is only to be used as a temporary control if
problems develop with the communication from the RT500.
12
RT500BC INSTRUCTION MANUAL
AFTER INSTALLATION
The following table shows the settings of the RT500 programmable
thermostat after Power on, or after RESET is pressed:
Function
Operation Mode
Room Temperature
°C indicator
Clock
AM/PM indicator
Day of Week indicator
Program
Set Point Temperature
Program Number indicator
SET indicator
PROG indicator
Frost Protection indicator
Heat indicator
Low-Battery Warning indicator
Output Relay
Status After Reset or Power On
Normal mode
22.0 °C, updated within 5 seconds
On
12:00
AM
M
Default factory setting
Default factory setting
5
Off
Off
Off
Off
Off, updated within 5 seconds
Off
After Power on, the thermostat will operate in Normal mode (Normal mode is
when the thermostat is displaying the room temperature):
• The set point temperature is reset to the default setting
• The room temperature display is updated within 5 seconds
• The control process starts
• The programme number is updated to indicate the running program
If the Reset Button is pressed, the RT500 will behave in the same way as
described above, user settings stored in the internal memory will be deleted and
overwritten with the default settings, and all programmable thermostat control
settings will be returned to default values.
RT500BC INSTRUCTION MANUAL
13
USER INTERFACE
The status and operation of the RT500 is clearly
shown on the display.
This display allows the user to see at a glance the
current status of the heating system, the current
time and day of the week, as well as a clear
indication of the current room temperature.
There are few user controls for the RT500,
making the programmable thermostat very
easy to operate. These controls are shown
below, along with a description of each of their
functions.
USER CONTROL FUNCTION SUMMARY
Key / Operation
UP key
Symbol
Functions
DOWN key
Decreases the selected setting
BACKLIGHT /
FROST key
SELECT key
SET key
Increases the selected setting
Manually turns on the LCD backlight
for 5 seconds, or activates /
deactivates Frost Protection
SELECT
Selects a clock or programme setting
and enters learning mode
Sets a clock or programme setting
SET
RESET button 14
Resets the programmable thermostat to default (original factory) settings
RT500BC INSTRUCTION MANUAL
OPERATION
The RT500 is configured and adjusted by
the use of a minimal number of user
controls.
SETTING THE TIME
Press and hold SET and SELECT when the
RT500 is in Normal mode for a few seconds
to enter the Clock setting mode. Release
both keys and the display will look like the
image below:
The Time and Day are displayed along with a SET indicator, with all other
indicators cleared from the display. The hour part of the time is flashing to
indicate that it is the currently selected item and is ready to be adjusted.
• Press the UP or DOWN keys to increase or decrease the ‘hour’ setting –
the
selected item will stop flashing while a key is pressed, and will resume
flashing when you release the key.
• Press the SELECT key to select the ‘minutes’ section of the time. Set the
minutes in the same way as the hour by using the UP and DOWN keys.
• Press SELECT again to select the Day, and again change the setting with
the UP and DOWN keys.
• Press the SET key to confirm the new time and day settings. This will store
the changes and return the RT500 to Normal mode.
The RT500 will also return to Normal mode (and save the clock settings) if
RT500BC INSTRUCTION MANUAL
15
PROGRAMMING THE RT500
The RT500 offers great versatility with its programming options, allowing
the user to programme the unit to operate on a 5/2 or 7 day control cycle.
The programmable thermostat has a default set of Programmes that have
been designed to meet the needs of most users. If these default programmes
are not suitable for your particular situation, reprogramming the RT500
with your own settings is a very straightforward operation.
Selection of the default programming mode (5/2 or 7 day) is made by
changing the jumper setting on the rear of the RT500 Control Unit, as
previously described within the Installation section of this manual.
5/2 DAY MODE
5/2 day mode is the default programming mode for the RT500. With this
mode selected, five different sets of time and set point temperatures can be
set for Weekdays or Weekends.
To review or change a programme, press the SET key when the RT500 is in
Normal mode. This will change the unit status to Programme Setting mode.
The LCD display will display programme number 1 and SET PROG, with all
other indicators cleared. The weekdays will be flashing to indicate they are
the selected item and are ready to be adjusted:
16
RT500BC INSTRUCTION MANUAL
Press the UP or DOWN key to select the programme set for either Weekday or
Weekend to be reviewed or adjusted. Pressing the SET key at any time when
in programming mode will return the RT500 into Normal mode.
Press the SELECT key to confirm the Weekday or Weekend selection. Once
this is set, the ‘Hour’ will flash to indicate that it is the selected item and is
the next item to be adjusted:
Press the UP or DOWN key to adjust the
hour setting to the desired value, and
confirm your selection by pressing the
SELECT key.
Pressing the SELECT key allows you
to step through each of the items to
be reviewed or adjusted within the
programmes in the following sequence:
Programme
Function Sequence
1
Hour
Minutes
Set point temperature
2
Hour
Minutes
Set point temperature
3
Hour
Minutes
Set point temperature
4
Hour
Minutes
Set point temperature
5
Hour
Minutes
Set point temperature
…before then allowing you to cycle back to Programme 1. Pressing the SET
key at any time will confirm the setting and return to the programme set
selection.
RT500BC INSTRUCTION MANUAL
17
7 DAY MODE
The RT500 also offers a 7 day programming mode, which allows you to
programme five different sets of time and set point temperatures for each
day of the week to give a total of 35 separate programme settings.
To review or change a programme, press the SET key when the RT500 is
in Normal mode. This will change the unit status to Programme Setting
mode.
The LCD display will display programme number 1 and SET PROG, with all
other indicators cleared. The weekdays will be flashing to indicate they are
the selected item and are ready to be adjusted.
Press the UP or DOWN key to change the
display to indicate the single day you
want to programme:
Pressing the SET key at any time when in programming mode will return the
RT500 into Normal mode. Press the SELECT key to confirm the Day selection.
Once this is set, the ‘Hour’ will flash to indicate that it is the selected item
and is the next item to be adjusted:
18
RT500BC INSTRUCTION MANUAL
Press the UP or DOWN key to adjust the hour setting to the desired value,
and confirm your selection by pressing the SELECT key.
Pressing the SELECT key allows you to step through each of the items to be
reviewed or adjusted within the programmes.
Pressing the SET key at any time will confirm the setting and return to the
programme set selection. Each programme for all the other days of the
week is set in exactly the same way – just repeat the steps shown above,
after entering programming mode and selecting the day you want to
programme.
Regardless of which programming mode the RT500 is set for (5/2 or
7 day), not pressing any keys for 15 seconds will automatically save any
programming changes and exit to Normal mode. You can also review or
change programme settings when Frost Protection is enabled.
RT500BC INSTRUCTION MANUAL
19
FROST PROTECTION
To enable the Frost Protection mode, press and hold the BACKLIGHT /
FROST button for a few seconds with the RT500 in Normal mode. Once
Frost Protection is enabled, the set point temperature is automatically set
to 5°C to provide protection from the risk of freezing.
Whenever Frost Protection is activated, the Frost Protection indicator will
flash in the sequence shown below:
While Frost Protection is activated, it will override any programme settings
until the mode is changed. To turn off Frost Protection mode, press and hold
the BACKLIGHT / FROST button for a few seconds.
REVIEWING SET POINT TEMPERATURE
You can view the set point temperature at any time by pressing either the
UP or DOWN key.
When any programme is running, the
LCD display will show the programme set
point temperature with the SET indicator
displayed:
20
RT500BC INSTRUCTION MANUAL
When operating in Frost Protection mode,
the LCD display will show a reading of 5
°C and also display the Frost Protection
indicator:
When operating in Temporary Override
mode, the LCD display will show the
temporary set point temperature:
To exit from the set point review, press any
key except the UP or DOWN keys, or don’t press any keys for a few seconds
– either of these actions will return the RT500 to Normal mode.
TEMPORARY OVERRIDE
It is possible to temporarily override the current set temperature of the
RT500. There are two ways to do this:
• While reviewing set point temperature: Pressing the UP or DOWN key
will increase or decrease the set point temperature in 0.5 °C steps.
• In normal mode press and hold either the up or down key to display the
set point temperature. After a few seconds the RT500 will enter temporary
override mode and will allow increase or decrease of the set point
temperature.
RT500BC INSTRUCTION MANUAL
21
Once in Temporary Override mode, the
clock and day are displayed, along with
the SET indicator; all other indicators are
cleared from the display. The set point
temperature will flash to indicate that it can
be changed:
The set point temperature can be adjusted within 5 °C to 35 °C.
Temporary Override mode remains active until the new set point settings
are adjusted, Frost Protection is activated or the next programme time /
temperature set point is reached.
On/Off Control
When the RT500 is operating in NORMAL mode, if the Boiler Control has
not received a signal from the RT500 after 1 hour, the Boiler Control will
turn off the boiler, and the LED indicator will flash constantly (two times
every second).
Once the Boiler Control receives a valid ON or OFF signal, the Boiler Control
will control the heating system accordingly.
22
RT500BC INSTRUCTION MANUAL
OTHER FUNCTIONS AND CONTROLS
Backlight
The backlight of the RT500 is switched on automatically whenever any of
the keys are pressed. The backlight will remain illuminated for a few seconds
after the last key press.
The backlight will not illuminate if the battery voltage is low.
Battery Status
The RT500 checks the battery voltage frequently during normal operation.
If the battery voltage is sensed as being low, the low battery indicator
will be displayed on the screen.
Although the programmable thermostat will continue to operate normally
at this stage, you should replace the batteries as soon as possible to prevent
any possible operating problems.
Reset Button
The Reset Button is provided as a way to restore the programmable
thermostat to its default factory settings. Pressing this button will delete
any previously entered settings.
Sleep Mode
By pressing both the UP and DOWN keys together for a few seconds, the
RT500 will enter SLEEP mode. In this mode, all of the functions will be
paused to save battery power, with the exception of the clock which will
continue to run in the background.
While in SLEEP mode:
• The LCD display will be blank.
• All output from the RT500 will be turned off immediately.
Press any key to wake up the RT500 and exit SLEEP mode.
RT500BC INSTRUCTION MANUAL
23
ENERGY TIP
One way to set and use your room thermostat is to find the lowest
temperature setting that you are comfortable with, and then leave it set
at this temperature. You can do this by setting the room thermostat to a
low temperature, (for example 17 °C) and then increasing the setting by
one degree each day until you are comfortable with the room temperature
- you won’t have to adjust the thermostat further, as adjustment above this
setting will waste energy 1 °C increase in temperature is equal to 3% of
your heating costs.
MAINTENANCE
The RT500 programmable thermostat requires no special maintenance.
Periodically, the outer casing can be wiped clean using a dry cloth (please
DO NOT use solvents, polishes, detergents or abrasive cleaners, as these can
damage the thermostat).
Should the RT500 programmable thermostat fail to function correctly,
check:
• The batteries are the correct type, fitted correctly and are not exhausted
- fit new batteries if in doubt.
• Heating system is switched on.
• If the RT500 is still not functioning correctly, press the Reset Button.
WARRANTY
SALUS Controls warrants that this product will be free from any defect
in materials or workmanship, and shall perform in accordance with its
specification, for a period of two years from the date of installation.
SALUS Controls sole liability for breach of this warranty will be (at its option)
to repair or replace the defective product.
24
RT500BC INSTRUCTION MANUAL
PRODUCT SPECIFICATION
Model:RT500BC
Type:
Electronic programmable thermostat with RF
Boiler Control, designed for Volt Free and AC
heating applications.
Programming
Programming Modes:
Number of Programmes:
Override Facility:
User selectable for 5/2 or 7 day option.
Five (5) user programmes plus factory
default programme.
User selectable programme override facility.
Default Programmes
Programme
1
2
3
4
5
Output
ON
TEMP
ON
TEMP
ON
TEMP
ON
TEMP
ON
TEMP
Weekday
6:00 AM
21 ºC
8:00 AM
14 ºC
4:00 PM
21 ºC
6:00 PM
21 ºC
10:00 PM
14 ºC
Weekend
6:00 AM
21 ºC
8:00 AM
21 ºC
4:00 PM
21 ºC
6:00 PM
21 ºC
10:00 PM
14 ºC
Note: The RT500BC is time and temperature controlled. A low temperature
set point can be used if an ‘OFF’ time period is required.
RT500BC INSTRUCTION MANUAL
25
Temperature
Scale:Celsius
Display Range:
5 ºC to 35 ºC
Display Resolution:
0.5 ºC
Tolerance:
Less than ± 0.5 ºC at 25 ºC
Setpoint Range:
5 ºC to 35 ºC
Measured Air Temperature Range: 5 ºC to 45 ºC
If room temperature is higher than 45ºC,display
will show HI. If it is lower than 5ºC, it will show LO.
Clock
Accuracy:
Display Format:
Frost Protection
± 1 minute per month
12 hour
Setting:5 ºC
RT500
Power Source:
Radio Frequency:
2 x AA alkaline batteries
(do not use rechargeable batteries)
868 MHz
Power Source:
Radio Frequency:
Switching Voltage:
Switching Current:
230V AC / 50Hz
868 MHz
0-230V AC / 50Hz
5A resistive, 1A inductive
Operating Temperature:
Storage Temperature:
0 ºC to + 40 ºC
- 20 ºC to + 60 ºC
Boiler Control
Environment
26
RT500BC INSTRUCTION MANUAL
RT500BC Warranty
SALUS Controls warrants that this product will be free from any defect
in materials or workmanship, and shall perform in accordance with
its specification, for a period of two years from the date of installation.
SALUS Controls sole liability for breach of this warranty will be (at its
option) to repair or replace the defective product.
Customer Name: ...................................................
Customer Address: ................................................
..............................................................................
Post Code: ..................... Tel No: ...........................
Email: ....................................................................
Engineers Company: .............................................
Tel No: ...................................................................
Email: ....................................................................
Date of Instalation: ................................................
Engineers Name: ...................................................
Engineers Signature: .............................................
RT500BC INSTRUCTION MANUAL
27
www.salus-tech.com
Sales:
Email: sales@salus-tech.com Tel: 01226 323961
Technical: Email: tech@salus-tech.com Tel: 01226 323961
SALUS Controls plc, SALUS House, Dodworth Business Park South,
Whinby Road, Dodworth, Barnsley S75 3SP
Open as PDF
Similar pages