HandyTone-701 User's Manual
Ver2.0.1 2016/02/08 created Ver2.0.2 2016/08/23 revised
Copyright © 2015 cloudippbx.com.
Thank you for purchasing Grandstream HT-­‐701. Before using the product, please read the manual carefully. AQer reading, store the manual in an accessible place. Check if all the accessories/aXachments are included in the package. ・ HT-­‐701 ・ AC Adaptor ・ Ethernet cable ・ User’s manual
DISCLAIMER ・ Features and specificaDons may be updated without prior noDce. Please bear with us. ・ The company will not be responsible for the development of noise and volume interrupDon and disconnecDon of calls that arise from the customer and this company’s network system. Please be advised that call quality is not guaranteed. ・ The company will not be responsible for inconsistency in call quality brought about by individual listening skills. ・ The company will not be responsible for the device damage that occurred outside Japan. ・ Please acknowledge that services in HandyTone-­‐701 may stop temporarily without prior noDce due to HT-­‐ 701’s scheduled maintenance. ・ Please acknowledge that the company will not be responsible in the event that the phone can no longer be used for calling due to damage or malfuncDon. ATTENTION ・ Wipe the device with soQ and dry cloth. Do not use wet towel. ・ Do not use products with chemicals as these may cause damage to the device. ・ If chemical dust cloth is used, read the accompanying direcDons carefully. Copyright © 2015 cloudippbx.com.
2
・ HandyTone-­‐701 HandyTone-­‐701 is an adaptor used to connect an analog phone device to Agile Phone. To use the device, the customer needs to subscribe to an Internet Service Provider. Customer with no broadband router features needs to provide a separate broadband router. Port
INTERNET
Descrip7on
Connects LAN cable’s (Ethernet) accessory.
DC 12V
Connects special AC adaptor accessory.
PHONE
Connects analog phone device. ※ Use appropriate phone cable accessory to analog phone when connecDng.
RESET
Use when restarDng the device.
・Connec7on Method 1. Switch the analog phone device’s line type to tone. 2. Connect the phone cable with HandyTone-­‐701’s Phone and analog phone device. 3. Connect Ethernet cable with HandyTone-­‐701’s Internet to a broadband router. 4. Connect AC Adaptor to HandyTone-­‐701’s DC 12VI and plug to an electric socket. ※ Perform the procedure in correct order. Make sure that cable and adaptor were plugged in properly. It takes a couple of minutes to place a call aQer connecDon. Please wait a moment. Copyright © 2015 cloudippbx.com.
3
・SeMng from Web Browser ① Confirm HandyTone-­‐701 device’s IP address. 1. AQer picking-­‐up the handset of the phone device that is connected to HandyTone-­‐701, dial ***. 2. If seeng is not yet performed, E103E, an English voice, will be played from the handset. AQer dialing #, confirm whether an English voice saying ENTER A MENU OPTION is played. ※ If already set, a voice saying ENTER A MENU OPTION will be played. 3. AQer ENTER A MENU OPTION is played, dial 02. An English voice telling HandyTone-­‐701’s IP address will be played. Example: 1-­‐9-­‐2.1-­‐6-­‐8.1.2 ② From web browser, open SeMng page. 1. From the HandyTone-­‐701 and computers connected within the same network, when launching Internet Explorer, etc. web browser, IP address should be entered following the format below. hOp://(IP Address)/ Example: If 192.168.1.2 is displayed, it should be entered as hXp://192.168.1.2/ 2. The above page will be displayed. Enter password and click Login. The iniDal password is admin. ③ Click the BASIC SETTINGS tab found at the upper por7on of the page. Time Zone: Select GMT+9:00 (Japan,Korea,Yakutsk). Once done, click Update and Apply respecDvely.
Copyright © 2015 cloudippbx.com.
4
・SeMng from Web Browser ④ Click the FXS PORT tab found at the upper por7on of the page. Copyright © 2015 cloudippbx.com.
5
・SeMng from Web Browser Copyright © 2015 cloudippbx.com.
6
・SeMng from Web Browser Primary SIP Server : Enter VoIP server. Outbound Proxy : Enter VoIP server. NAT Traversal : Select keep-­‐alive. SIP User ID : Enter Unique (10 numeric characters) AuthenDcate ID : Enter Unique (10 numeric characters) AuthenDcate Password : Enter device password. Name : Enter Unique (10 numeric characters) Local SIP Port: any Port number in range of 50000~60000
*Please allocate different port number to each devices without overlapping.
Ex.) Device A : 50000, Device B : 500001 Check SIP User ID for Incoming INVITE : [Yes]
*It will be blocked unauthorized access to the devices.
Preferred DTMF method: Supply Priority 1, 2 and 3 with the same informaDon as below: Priority 1: RFC2833 Priority 2: In-­‐audio Priority 3: SIP INFO *Set [in-­‐audio] as Priority 1 in case [DTMF inband] are set on Unique Management Page.
Disable Call-­‐WaiDng: ・ SelecDng Yes will noDfy new caller that line is busy when the callee is sDll at the middle of the call. ・ SelecDng No will noDfy new caller to assume that the line is ringing/acDve even when the callee is at the middle of a call. ※ This is an opDonal seeng. No seeng required if no need.
※ Default is [No]. Factory seeng by the company : [Yes] SUBSCRIBE for MWI : Select [Yes, send periodical SUBSCRIBE for Message WaiDng IndicaDon]
Caller ID Scheme: Set using the example below. ・ NTT Japan : Select when connecDng to a phone device that supports number display ※ It is important to set phone that supports number display. Please refer to the device’s instrucDon manual for the setup method. ・ Bellcore/Telcordia : Select this when using phone other than NTT Japan. ※ The prescribed value is Bellcore/Telcordia. The default factory seeng is NTT Japan. If the device does not support number display, change the seeng to Bellcore/Telcordia. Once done, click Update and Apply respecDvely.
Copyright © 2015 cloudippbx.com.
7
・SeMng from Web Browser ⑤ Click the ADVANCED SETTINGS tab found at the upper por7on of the page.
NTP Server: Enter ntp.jst.mfeed.ad.jp. Once done, click Update and Apply respecDvely. Click Reboot. The device will be restarted and seengs will be applied. ・ Important points when using Agile Network Always disable the alert info header seeng in Unique that you are using on the device. Incoming call will be blocked when this seeng is enabled. From website, open Unique Management page. Click Unique Seeng, then, go to General Seeng. In Alert Info Header Seeng, select DISABLE.
Copyright © 2015 cloudippbx.com.
8
・ Confirma7on SeMng from English Voice Guidance 1. Pick-­‐up the handset. 2. From HandyTone-­‐701 connected phone device, enter * * *. From the handset, a voice guidance saying ENTER A MENU OPTION will be played. When you dial *, confirming the status, DHCP mode or STATIC IP mode, is possible. 3. Enter menu number from phone device and perform confirmaDon of seeng. 4. As needed, dial 9 and set the operaDon.
Menu Number
English Voice Guidance
Opera7ng procedure/Contents
01
DHCP MODE ( Dynamic Host ConfiguraDon Protocol Mode ) and STATIC IP MODE
Warning: StaDc IP mode is not supported in Agile Phone service.
02
IP ADDRESS
Voice guidance for the current HandyTone’s IP address will be played.
03
SUBNET
The current subnet mask’s IP address will be played in voice guidance.
04
GATEWAY Voice guidance for the current gateway’s IP address will be played. 05
DNS SERVER
Voice guidance for the current DNS server’s IP address will be played.
INVALID ENTRY Returns to Main Menu automaDcally. Copyright © 2015 cloudippbx.com.
9
Safety Precau,ons This manual contains precauDons to assure user’s safety while using this product.
If the precauDons are disregarded, the extent of consequences is presented below. WARNING
This indicates that ignoring or mishandling of this noDce might result to death or serious injury to the person.
This indicates that ignoring or mishandling of this noDce might result to harm to the person.
CAUTION
WARNING
Immediately unplug the device from the power supply if there is a strange smell and smoke. Don’t use the device and immediately contact the dealer for repair. This may cause fire or explosion. Do not disassemble or modify. The device may malfuncDon, cause electric shock and fire.
Do not insert metal to the opening or drop the product. If in case a metal is inserted to the device, unplug the device and contact the dealer. The device may malfuncDon, cause electric shock and fire.
Do not pour water or any foreign object inside the device. If in case water or any foreign object is poured or inserted to the device, unplug the device and contact the dealer. Do not touch the device when lightning occurs. This may cause electric shock.
Do not use in bathroom or shower room. The device may malfuncDon, cause electric shock and fire.
Don’t place in a damp, dusty or direct sunlight. The device may malfuncDon, cause electric shock and fire. This device is not waterproof. If in case water entered the device, unplug the device and contact the dealer. CAUTION
Immediately unplug the device from the power supply if there is a strange smell and smoke. Don’t use the device and immediately contact the dealer for repair. This may cause fire or explosion. Do not disassemble or modify. The device may malfuncDon, cause electric shock and fire.
Do not insert metal to the opening or drop the product. If in case a metal is inserted to the device, unplug the device and contact the dealer. The device may malfuncDon, cause electric shock and fire.
Do not pour water or any foreign object inside the device. If in case water or any foreign object is poured or inserted to the device, unplug the device and contact the dealer. Do not touch the device when lightning occurs. This may cause electric shock.
Do not use in bathroom or shower room. The device may malfuncDon, cause electric shock and fire.
Copyright © 2015 cloudippbx.com.
10
Troubleshooting
PROBLEM
CAUSE SOLUTION
General Failure
Please plug and unplug from the power source. (Do this a few times).
Please wait at least one minute before you again plug the device to the power source.
No ringer sound
Ethernet cable is disconnected.
AC adapter is disconnected.
Did you change the volume settings?
Did you change the settings on the display”
Please check the connection of the Ethernet cable.
Please check the connection of the AC adapter.
Please adjust the volume on the button.
Revert the change settings.
Disconect the Ethernet cable (reboot).
Are there ani abnormalities in the network environment?
Please check your network environment.
Call is interrupted
by noise
1. From web browser, open Setting page and Login.
2. Click BASIC SETTINGS tab found at the upper portion of the page. 3. Reset Type: Immediately after selecting Full Reset, press the Reset button. 4. The phone device will be restarted and the phone will be initializing. Copyright © 2015 cloudippbx.com.
11
Open as PDF
Similar pages