Digital High Definition Satellite Receiver SRT 7100

Picture similar
Digital High Definition
Satellite Receiver SRT 7100
User Manual
1
3
2
Fig. 1
1
Fig. 2
Fig. 3
2
3
6
4
5
9
7
8
10
SCART
Fig. 4
A
B
C
HDMI
Fig. 5
A
B
A
Fig. 6
C
A
B
C
PART 1 • English
2
2
2
3
3
3
2.0 Your Receiver
2.1 DEFAULT PIN-CODE: 0000
2.2 Front Panel
2.3 Rear Panel
2.4 Remote Control Unit
3
3
3
4
4
3.0 Connections
3.1 Basic connection using a Scart cable
3.2 Basic connection using an HDMI cable
3.3 Connecting multiple fixed dishes using a DiSEqC 1.0 switch
3.4 Connecting and using the IR extender
5
5
5
5
5
4.0 Starting up for the first time
4.1 Language selection
4.2 System Setup
4.3 Satellite Selection
4.4 Scan Mode
4.5 Signal Adjust
4.6 Channel Setup
6
6
6
6
6
6
7
5.0 Quick guide to using your receiver
7
6.0 Operation
6.1 Changing channels
6.2 Info Banner
6.3 Selection of audio language
6.4 Teletext
6.5 Subtitles
6.6 Changing the video format
6.7 EPG (Electronic Programme Guide)
6.8 Instant Recording
6.9 Timeshift
7
7
8
8
8
8
8
8
9
9
7.0 Main Menu
7.1 Installation
7.2 Setup
7.3 Channel
7.4 Advanced
7.5 Games
9
9
11
13
16
17
8.0 TROUBLESHOOTING
17
9.0 SPECIFICATIONS
19
STRONG declares that this item complies with the basic requirements and other relevant regulations of
directives CE 2004/108/EEC and 73/23EEC; RoHS 2002/95EEC
Subject to alterations. In consequence of continuous research and development technical specifications,
design and appearance of products may change. ASTRA is a registered trade mark of SES ASTRA,
Eutelsat and HOT BIRD are registered trademarks of Eutelsat Communications, all other product names
are trademarks or registered trademarks of their respective owners.
© STRONG 2010. All rights reserved. 04/2010
* €0,14/Min. from German wired line
* €0.42/Min. max. from mobile network
* €0,12/Min. from Austrian wired line
per March 2010
1.0 INTRODUCTION
1.1 Safety Instructions
1.2 Storage
1.3 Equipment Set-up
1.4 Accessories
1.5 Usage of external USB devices
English
Table of Contents
* €0,14/Min. from French wired line
1
PART 1 • English
1.0 INTRODUCTION
1.1 Safety Instructions
DO NOT INSTALL YOUR RECEIVER:
In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface
which might obstruct the ventilation slots.
DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:
„„
To direct sunlight or any other equipment that generates heat; to rain or intense moisture; to
intense vibration and to any shock which may cause permanent damage to your receiver or to
any magnetic objects, such as loudspeakers, transformers, etc.
„„
Do not use a damaged power cord. It may cause a fire or an electrical shock. Do not touch a
power cord with wet hands. It may cause an electric shock.
„„
When the receiver is not used for a long period of time, you should unplug the power cord
from the wall socket.
„„
Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you may clean
your receiver with a soft lint-free cloth slightly made damp with a mild soap solution, only after
disconnecting from the mains voltage supply. Make sure no foreign objects fall through the
ventilation slots because this could cause fire or an electric shock.
„„
Do not place any objects on top of the receiver because this might prevent proper cooling of
the components inside.
Safety Precautions
„„
Never open the receiver cover. It is dangerous to touch the inside of the receiver due to high
voltage currents and possible electrical hazards and your warranty will be void. Refer all
maintenance or servicing to suitably qualified personnel.
„„
When you are connecting cables, be sure that the receiver is disconnected from the mains
supply voltage. Wait a few seconds after switching off the receiver before you move the receiver
or disconnect any equipment.
„„
It is a necessity that you only use an approved extension and compatible wiring that is suitable
for the electrical power consumption of the installed equipment. Please ensure that the
electrical power supply corresponds with the voltage on the electrical identification plate at the
back of the receiver.
„„
If the receiver does not operate normally even after strictly following the instructions in this
user manual, it is recommended to consult your dealer.
1.2 Storage
Your receiver and its accessories are stored and delivered in a packaging designed to protect against
electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep
the packaging away from children. For transporting the receiver from one place to another or if you are
returning it under warranty conditions, make sure to repack the receiver in its original packaging with its
accessories. Failing to comply with such packaging procedures could void your warranty.
2
PART 1 • English
1.3 Equipment Set-up
English
We recommend you consult a professional installer to set up your equipment. Otherwise, please follow
the instructions below:
Refer to the user manual of your TV and your antenna.
Make sure that the SCART cable and outdoor components are in a good condition and the SCART
connections are well shielded
This manual provides complete instructions for installing and using this receiver. The following symbols
will serve as follow.
WarningIndicates warning information.
TipsIndicates any other additional important or helpful information.
MENURepresents a button on the remote control or the receiver (Bold Character)
Move toRepresents a menu item within a window. (Italic Character)
1.4 Accessories
„„
User’s
Manual
Remote control unit
„„
IR Extender
„„
2x Batteries (AAA type)
„„
1
Note:The batteries should not be recharged, disassembled, electrically shortcircuited, be mixed or used with other types of batteries.
1.5 Usage of external USB devices
It is recommended to use USB 2.0 storage devices. If your device is not compatible to USB 2.0 specifications,
recording, playback and other multimedia functions of the receiver would not work properly.
STRONG cannot guarantee compatibility to all types of USB storage devices.
It is advised not to store important information on USB storage devices used with the receiver. Always
make backups of data on your USB storage device before using it with this receiver. STRONG will not
take responsibility for any loss of information or circumstances caused by loss of information.
Please ensure that either the USB device is already formatted to FAT/FAT32, or format the USB device via
your receiver, refer to chapter 7.3.3 File Explorer for details.
2.0 Your Receiver
2.1 DEFAULT PIN-CODE: 0000
2.2 Front Panel
Fig.1
1. Standby/ON switchturns the receiver ON or to Standby
2. USB connectorconnect your USB device (stick, HDD, etc.) to this port
3. 4 digit LED displaydisplays channel number or time, depending on settings.
3
PART 1 • English
2.3 Rear Panel
Fig 2.
1. SAT INTo connect to the LNB of your satellite dish for reception of satellite
broadcast signal
2. SAT OUTTo loop through the satellite signal to a second receiver
3. IR
To connect the IR extender
4. AUDIO (L/R)To connect to the audio input of your HIFI or television
5. S/PDIFTo connect to a digital or home cinema audio amplifier
6. VIDEO (RCA)To connect to the RCA video input of your TV or VCR using an RCA cable
7. TV SCARTTo connect to TV using a SCART cable
8. HDMITo connect to the HDMI input of your TV using a good quality HDMI cable.
9. Power switchTo switch the mains power ON or OFF
10. Power cordThe receiver requires a mains voltage of 100~240V AC 50~60Hz (auto
selecting). Please check the local power conditions before connecting
the receiver to the mains supply.
2.4 Remote Control Unit
Fig. 3.
qTurns the receiver ON/Standby
!Mutes the audio output of the receiver
[0~9]Channel number and numeric value input
SATSatellite selection in normal viewing and channel mode
TV/RToggles between TV and Radio mode
MENUDisplays the menu in viewing mode or to go back one step in the menu
EXITGo back one step in the menu/cancellation of current process/exit
from main menu to viewing mode
8. pqSwitches to the next/previous channel in viewing mode or moving the
highlight up/down in the menu
9. tuIncreasing/decreasing of the volume level in viewing mode or
changing values of settings in the menu
10. OK
Viewing mode:Displays the channel list. Menu: activation of the
highlighted item
11. FAVToggles between available favourite groups and all channels list
12. EPGViewing mode:
Displays the EPG (Electronic Program Guide)
13. V+/V-Increasing/decreasing of the volume level
14. INFOPress once to display channel number/name and now/next info.
Press twice to display frequency/signal strength information.
15. AUDIODisplays the audio selection menu with selections for available
languages and audio modes
16. V.FToggles between available HDMI screen resolutions
17. P+/P- Switches to next/previous channel in viewing mode
18. RED/RCLToggles between the current channel and the previous channel in
viewing mode
1.
2.
3.
4.
5.
6.
7.
4
PART 1 • English
English
19. GREEN/PAUSEFreezes/resumes the current broadcast
20. YELLOW/SUBDisplays a list of available subtitling for the current channel
21. BLUE/TEXTDisplays the teletext browser
22. 2Freezes/resumes the playback of recordings or music files
23. :Jumps to the previous track during MP3 playback
24. "Jumps to the next track during MP playback
25. 4Starts recording of the current broadcast
26. 1Starts playback of the selected file in File Explorer
27. 6Fast forward
28. 5Fast rewind
29. 3Stop
3.0 Connections
3.1 Basic connection using a Scart cable
Fig. 4.
AConnect the LNB of your satellite dish to the SAT IN connector of your receiver using a good
quality coax cable and suitable ‘F-connector’ plugs.
BConnect one end of a good quality Scart cable to the TV SCART connector on your receiver and
the other end to the SCART input of your TV.
CPlug the power cord to a suitable wall outlet.
3.2 Basic connection using an HDMI cable
Fig. 5.
AConnect the LNB of your satellite dish to the SAT IN connector of your receiver using a good
quality coax cable and suitable ‘F-connector’ plugs.
BConnect one end of a good quality HDMI cable to the HDMI output on your receiver and the
other end to the HDMI input of your TV.
CPlug the power cord to a suitable wall outlet.
3.3 Connecting multiple fixed dishes using a DiSEqC 1.0 switch
Fig. 6.
AConnect the LNB’s of your fixed dishes to the inputs of a DiSEqC 1.0 switch
BConnect the output or “to receiver” connector of the DiSEqC 1.0 switch to the SAT IN connector
on your receiver.
CRefer to section 3.1 or 3.2 for TV and mains connections.
3.4 Connecting and using the IR extender
The included IR extender allows you to place the receiver out of sight (e.g. in a closed cabinet) while
still being able to control it. Plug the IR extender into the IR connector on the back of the receiver.
Locate the extender on a position giving it direct sight to the remote control. Once a suitable location is
found, remove the protecting foil from the adhesive tape on the back of the extender and fix it by slightly
pressing it down on the surface it should be placed on.
5
PART 1 • English
4.0 Starting up for the first time
Ensure that your satellite signal is of good quality and that all connections are sound. In case of
difficulties or questions, please ask you local dealer for assistance. It is recommended to follow the Setup
Wizard step by step. It will guide you through the basic installation and channel searching process. You
can enjoy digital HD broadcasts within just a few minutes.
4.1 Language selection
After turning on the power for the first time, the language selection menu will appear. Choose your language
with pq and confirm with OK. A welcome screen will now be displayed. Once you are ready, press OK to
start the wizard. During any stage of the Setup Wizard, you can press EXIT to get back to the previous screen.
4.2 System Setup
Here you can set the Country, Aspect Ratio, Conversion Mode and Subtitle Language. Use pq to move
the highlight and tu to change settings. To see a list of all possible settings for the highlighted option,
press OK. Once all settings are made, move the highlight to NEXT and press OK to continue.
4.3 Satellite Selection
Use pq to highlight the satellite your dish is aimed at and press OK to confirm.
If your dish is aimed at Astra 1C, 1E, 1F, select ASTRA 19.2E. The SCAN MODE screen will appear.
If your dish is aimed at HOT BIRD, select HOTBIRD 13E.The SCAN MODE screen will appear.
If your dish is aimed at another satellite, select OTHER. You will be guided to the Satellite Settings menu.
Refer to chapter 7.1.1 for instructions.
Note:If Germany is chosen as country and ASTRA 19.2E as satellite, German preinstalled channels are available. An extra screen will then be displayed giving a
choice between Preinstalled & Scan and Satellite Scanning. Choose Preinstalled &
Scan to install the German pre-installed channels and continue with the Setup
Wizard as described from point 4.4 or choose Satellite Scanning to continue
without pre-installed channels.
4.4 Scan Mode
Use pq to highlight the desired option and press OK to confirm.
All:
Will scan all available channels on the chosen satellite.
Free:
Will scan FTA (Free-To-Air) channels only.
4.5 Signal Adjust
This screen allows you to fine tune the alignment of your dish antenna for optimum reception.
Use tu to select the switch input the dish is connected to. (If the LNB of your dish is directly connected
to the receiver, choose Switch Input 1) The bars on the bottom of the screen indicate the current signal
strength and quality. A red bar indicates a bad signal. Green bars indicate a good signal. Yellow bars
indicate that the signal condition is nearly acceptable.
Adjust your dish for maximum possible signal quality and strength. Once the signal cannot be improved
anymore, fix the dish on this position and press OK to continue.
6
PART 1 • English
4.6 Channel Setup
English
Your receiver will now perform an automatic channel search. Once the process is finished, all found
channels will be stored and the receiver will switch to the first found channel. You are now ready to enjoy
your new receiver.
Note:If no channels were found during the automatic channel scan, the receiver will
display the Satellite Settings menu. Please refer to chapter 7.1.1 for instructions.
5.0 Quick guide to using your receiver
We at STRONG understand that you can’t wait to enjoy your new HD receiver. The following quick guide
will make you familiar with the basic operation of this device. We do, however, advice you to read the full
manual to get the best performance from your STRONG HD receiver.
To turn your receiver ON or to Standby, use the q button on the remote control or the button on the left
side of the front panel.
Choose the desired channel with the pq buttons or the P+/P- buttons. Alternatively, you can digit the
channel number with the [0~9] buttons on the remote control. Or press OK in viewing mode to display
the channel list.
The volume can be adjusted with the V+/V- buttons or the tu buttons.
6.0 Operation
In viewing mode, several features are available to make watching TV a true pleasure. This paragraph
describes these features. Please also read chapter 7.0 to get familiar with the menu of your new receiver.
6.1 Changing channels
Your new receiver is equipped with three ways to change channels.
„„
via direct access
„„
via the channel list and
„„
via the P+/P- keys.
6.1.1 Direct access
To gain direct access to a certain channel, simply input its number with the [0~9] key’s on the remote
control. Channel numbers can be up to four digits long. Entering a number with less than four digits is
possible. Just wait a few seconds and your receiver will switch to the selected channel.
6.1.2 Channel list
Press OK in viewing mode to display the Channel List. Use pq in the Channel List to highlight your
channel of choice and press OK once to select the highlighted channel. Press OK again to leave the
Channel List. The Channel List is equipped with a filter function to make finding your favourite channels
easier. While in the Channel List, press RED. An alphabet banner will now be displayed. Use pq to select
the first letter of the desired channel and OK to confirm. All channels beginning with the chosen letter
will now be displayed.
7
PART 1 • English
The following keys are available in the Channel list and viewing mode:
TV/R:Toggles between TV and radio channels
SAT:changes the satellite
FAV:to switch to one of the available favourite lists.
6.1.3 Using the P+/P- keys
P+ or p will switch to a higher channel.
P- or q will switch a lower channel.
6.2 Info Banner
At any time during viewing mode you can press the INFO button to get info about the current channel
and program*. Press INFO twice to see technical details about the current channel.
* Program information is displayed when available. Availability depends from broadcast.
6.3 Selection of audio language
Some channels support a choice of different audio formats and/or languages. To select another audio
stream, press AUDIO in viewing mode. A list with available audio streams will now be displayed. Use
pq to select the desired stream and confirm with OK.
6.4 Teletext
Your receiver includes a fully featured Teletext. To access Teletext, press the BLUE button in viewing mode
and use the [0~9] buttons to input the number of the page you wish to see. The coloured buttons of the
remote control allow you to jump to selected pages directly, as indicated on the bottom of the teletext
screen. Press EXIT to go back to viewing mode.
6.5 Subtitles
Some channels support a choice of different DVB subtitle languages. Press SUB in viewing mode to
display a list of available subtitle languages.
6.6 Changing the video format
To change the video format while watching TV, simply press the V.F key in viewing mode. A list with available
HDMI resolutions will pop up. Select the desired resolution using pq. It is also possible to change the
Aspect Ratio or Conversion Mode from the Video Format banner. Use the tu buttons to select the option of
choice and use pq to change to the setting. Once all settings are made, press OK to apply.
6.7 EPG (Electronic Programme Guide)
The Electronic Programme Guide is a very useful function that allows you to watch programme schedules
and information on screen and to mark programs for recording. Use pq to select the desired channel
and u to move the highlight to the program list. In the program list, use pq to select or scroll through
programs. Use OK to display detailed information about the selected program. Use RED to display
program information for the next day and GREEN to get back one day. Simply press YELLOW to get back
to today’s information.
Note:Availability of EPG data depends on broadcast.
8
PART 1 • English
6.8 Instant Recording
Your new receiver allows you to make an instant recording of the program you are watching. Simply press
4 to start the recording. To enter the duration for the recording, press 4 again. Use the [0~9] keys to
input the desired recording time.
During the recording a banner showing the elapsed recording time will be shown on the upper right of
your TV screen. To stop the recording, press 3.
* Please connect an USB storage device with sufficient free space before you start a recording. For
recording HD broadcast, a high speed device is needed.
6.9 Timeshift
The Timeshift function allows you to pause live broadcasts and resume normal watching without missing
anything. Press 2 to freeze the current broadcast. Press 2 again to start time shifted playback. To stop
Timeshift, press 3.
Note:The Timeshift will only work correctly when a fast USB storage device such as
an USB2.0 HDD is connected to the receiver. Distorted picture and / or audio
during Timeshift indicate a low USB device speed. STRONG cannot guarantee
for USB devices used. Especially when Timeshift is activated at channels with
high data rate (High quality SD/HD), STRONG cannot guarantee an accurate
Playback of the Timeshift file.
7.0 Main Menu
All important settings and features of your receiver can be operated from the Main Menu. It consists
of the following sub-menus: Installation, Setup, Channel, Advanced and Games. Use tu to select a
sub-menu and pq to choose an option. Press OK to advance to the chosen submenu. Press MENU in
viewing mode to display the Main Menu.
7.1 Installation
The installation menu allows you to change satellite settings and to search for channels. It consists of the
following sub-menus: Satellite Settings, Auto Scan, Manual Scan and Satellite Edit. Choose the desired sub
menu with pq and press OK to advance.
7.1.1 Satellite Settings
Use this menu to change the settings for a given satellite and to configure the parameters for the used
antenna Use pq to highlight Satellite and tu to set the satellite you wish to change the settings for.
To see a list with all available satellites, press OK when the highlight is on Satellite. Use pq to highlight
9
English
Booking a program from EPG
Select a program as described above. Once the desired program is selected, press BLUE. This will lead
you to the timer menu. All details are already filled in for you. Make a choice between Play or Record
action and save the timer. Please refer to section 7.3.4 for details.
PART 1 • English
Transponder and tu to set the desired transponder. Signal bars indicating signal quality and strength
can be found on the bottom of the screen. These bars show the signal conditions for the chosen satellite
and transponder. You can now adjust the following settings: LNB type, LO Frequency, LNB power, Band
(22 kHz), Switch Type, Switch Input, Dish Mode and Dish Position. Once all settings are made, press exit
to get to the previous menu or use pq to highlight Go To and tu to select Auto Scan or Manual Scan
to advance to Auto Scan or Manual Scan.
A confirmation banner will now be displayed. Press OK to confirm the made changes or EXIT to discard.
7.1.2 Auto Scan
Use this menu to perform an automatic channel search on one or more satellites.
On the left of the screen, a list with satellites is displayed. Use pq to highlight the satellite(s) you wish
to scan and press OK to mark the highlighted satellite. Press OK again to unmark a marked satellite.
Note:you can mark multiple satellites. Auto Scan will search all marked satellites for
available channels.
Now select the desired scanning options on the right of the screen. Use u pq to highlight and OK to
set an option.
Scan Mode All:scan all channels
Free:scan Free-To-Air channels only
Scrambled:scan scrambled channels only.
Service Type All:scan TV and Radio channels
TV scan:TV channels only
Radio:scan radio channels only.
Network Search Disabled:no network search
Enabled:network search will be performed.
Once all settings are made, press the GREEN button on the remote control to start the scan or EXIT to
quit without scanning. All newly found channels will be stored at the end of the channel list.
Tip:Network Search: If Disabled is selected, the receiver will search only for
channels available from the preset transponder list of the selected satellite. If
it is set to Enabled, the receiver will perform an additional search for channels
from the NIT table (NIT= Network Identification Table). Use this option to
receive new launched channels from the selected satellite.
7.1.3 Manual Scan
Use this menu to scan a single transponder only.
The following can be set: Satellite, Transponder, Frequency, Polarisation, Symbolrate, Scan Mode, Service
Type and Network search. Use pq to move the highlight to the chosen setting and tu to change its
value. Once all settings set correct, press the GREEN button to start scanning or EXIT to quit. All newly
found channels will be stored at the end of the channel list.
10
PART 1 • English
7.1.4 Satellite Edit
Here you can edit transponder data or add a new satellite.
On the left of the screen, a list with all available satellites is displayed. The right of the screen displays a
list will all available transponders for the highlighted satellite.
Adding or editing a transponder
Use pq to highlight the desired satellite. Press u to move the highlight to the transponder list. Press
YELLOW to add a transponder or use pq to highlight the transponder to be edited and then press
BLUE to enter the edit screen. Use pq to navigate in the edit screen and use tu respectively [0~9] to
change the settings. Once all settings are made, press GREEN to save or EXIT to quit without saving.
Editing an existing satellite
Use pq to highlight the satellite you wish to edit. Press BLUE to go to the Satellite Edit screen. To edit
the name of the satellite, use pq to highlight the name and press OK. A keyboard will pop up. Use pq
tu to navigate and OK to input the chosen character. Once finished press GREEN to save the changes
or EXIT to quit without saving. To edit the position of the satellite, use pq to move the highlight
to Position and use the [0~9] buttons to input the new position. To change the location, use pq to
highlight Location and use tu to change the location. Possible settings are: East and West. Once all
settings are made press GREEN to save or EXIT to quit without saving.
Adding a satellite
To add a satellite, make sure the highlight is not in the transponders list (press t in case of doubt) and
press YELLOW. The procedure for adding a satellite is the same as for editing a satellite.
7.2 Setup
Use the Setup menu to configure the system settings of your receiver. The following sub-menus are
available: Language, Output Options, Time Setting, Parental Control and OSD Display. Choose the desired
submenu with pq and press OK to advance.
7.2.1 Language
Here you can set the preferred Display, Audio and Subtitle languages and Country setting. Use pq to
highlight the setting you wish to change and tu to change the value of the highlighted setting. Press
OK for a list with all available options for the chosen setting.
Display:This setting affects the menu language of your receiver. All menu’s and
messages will be displayed in this language.
Audio:is the preferred audio language. The receiver will automatically switch audio to
the preferred language whenever available.
Subtitle:Whenever available, subtitles will be displayed in the selected language.
Country:Here you can set your country of residence.
11
English
Note:Press YELLOW in the Manual Scan menu to make settings for a PID search.
Scan mode, Service type and Network search will then be replaced by settings for
Video PID, Audio PID and PCR PID. For information on PID values, please visit
websites like: www.lyngsat.com or www.kingofsat.net
PART 1 • English
Once all settings are made, press EXIT to leave the Language menu. A confirmation banner will be
shown. Press OK to save your settings or EXIT to discard.
7.2.2 Output Options
This is the menu to configure the audio and video outputs of your receiver. Use pq to highlight the
setting you wish to change and tu to change the value of the highlighted setting. Press OK for a list
with all available options for the chosen setting.
TV Standard:Set the standard corresponding to your TV set. Available options are: Auto,
NTSC, PAL and SECAM.
Aspect Ratio:Use this option to set the aspect ratio of your TV set. Available options are: 4:3
and 16:9.
Conversion mode:Use this option to set the preferred way of converting 16:9 broadcasts to 4:3 TV
format. You can choose between the following options: Letter-box (the full 16:9
picture will be displayed on your 4:3 TV set with black bars above and below the
picture.), Pan and scan (The centre of the 16:9 picture will be displayed full-screen
on your 4:3 TV) and Combined (Combination of Letter-box and Pan and scan.)
SCART Mode:Select RGB for the best picture quality or CVBS in case your TV doesn’t support RGB.
Digital Audio:Defines the format available on the S/PDIF output of your receiver. When set
to PCM, the digital output will always output PCM stereo regardless of the
broadcasted audio format. The Auto setting will pass all incoming digital audio
through the digital output. Use this option if you have your receiver connected
to a digital surround amplifier. The digital output can be switched off by setting
Digital Audio to Off.
Video Format:This setting is only active when the receiver is connected to the TV set via
HDMI. It allows you to set the preferred HDMI screen resolution. Available
options depend from your TV set.
Once all settings are made, press EXIT to leave the Output Options menu. A confirmation banner will be
shown. Press OK to save your settings or EXIT to discard.
7.2.3 Time Setting
This menu allows you to set the way the receiver collects and adjusts the time. You can also adjust the Auto
Power Down function here. Use pq to highlight the setting you wish to change and tu or [0~9] to change
the value of the highlighted setting. Press OK for a list with all available options for the chosen setting.
Time Display:
Defines when the front panel display will show the clock. Possible settings are:
Off and Stand-by only.
Use GMT:On: the receiver will use broadcast time. Use the Time Zone setting to define
the deviation from GMT time. Summer Time can be set to On or Off.
Use GMT:Off: Allows you to enter the time settings manually. Use the [0~9] buttons to set
the current time in the Local Time option. Use pq to move the highlight to
Local Date and press OK. A calendar will be displayed. Use pqtu to select
the actual date and press GREEN to confirm.
12
PART 1 • English
English
Auto power down
Auto Power Down is a new, power saving feature that helps you with reducing power consumption.
It will switch off the receiver when no command is given for at least the set time. Possible settings
are: 1~6 hours with one hour steps and Disabled.
Once all settings are made, press EXIT to leave the Time Setting menu. A confirmation banner will
be shown. Press OK to save your settings or EXIT to discard.
7.2.4 Parental Control
In this menu you can enable or disable the menu lock function and change the PIN code. Use pq to
highlight the setting you wish to change and tu or [0~9] to change the value of the highlighted setting.
Menu Lock:If Menu Lock is set to Enabled, items in the Main Menu are only accessible
after entering the PIN. (Default PIN: 0000) When set to Disabled, all menu
items are freely accessible.
Change PIN Code:Use this function to set your own personal PIN code. Highlight Change
PIN Code with pq and press OK to advance. A banner with three fields
pops up: Enter your old PIN at PIN Code. (Default PIN: 0000) Enter your
new PIN at Enter New and again at Reconfirm. A successful change of
PIN is confirmed by an on screen message. Use EXIT to go back to the
previous menu.
Once all settings are made, press EXIT to leave the Parental Control menu. A confirmation banner
will be shown. Press OK to save your settings or EXIT to discard.
7.2.5 OSD Display
This menu allows you to set the OSD (On Screen Display) functionality of your receiver according
to your wishes. Use pq to highlight the setting you wish to change and tu or [0~9] to change the
value of the highlighted setting. Press OK for a list with all available options for the chosen setting.
Banner Show:When set to On, the info banner displaying channel name, channel
number and Now/Next information will be shown every time you change
channels. To disable the banner, set this item to Off.
Banner time (sec.):defines the time after which the OSD banners time out. Possible settings
are: 1~10 seconds.
Transparency:Defines how transparent the On Screen Display and banners are. Possible
settings are: 0%, 25%, 50% and 100%.
Once all settings are made, press EXIT to leave the OSD Display menu. A confirmation banner will
be shown. Press OK to save your settings or EXIT to discard.
Tip:For detailed information about the “Info banner” please refer to
chapter 6.2 Info Banner
7.3 Channel
Within this menu you can manage channels and configure favourites, play files from a connected USB
storage device and to set timers. The Channel menu consists of the following sub-menus: Sort and Edit,
Favourite, File Explorer and Timer. Choose the desired sub menu with pq and press OK to advance.
13
PART 1 • English
7.3.1 Sort and Edit
Use this menu to manage channels in the channel list. Set the satellite you wish to manage channels on
in the left column. Select All Sat to display the channel list with channels from all installed satellites.
Sorting a channel list
Use pq to select the desired satellite and TV/R to toggle between TV and radio channels. Press YELLOW to
display the Sort in Order banner. Use pq to select the sorting method of your choice and OK to confirm.
(Un) locking or deleting all channels in the current list
Use pq to select the desired satellite and TV/R to toggle between TV and radio channels.
To delete all channels in the chosen list, press RED. All channels in the chosen list will be marked for
deletion. Press GREEN to confirm this action.
To lock all channels in the chosen list, press OK. All channels in the chosen list will be marked as locked.
Press GREEN to confirm this action. Locked channels can only be accessed after entering the correct PIN
code. (Default PIN: 0000)
Deleting, editing or moving one channel only
Use pq to select the desired satellite and TV/R to toggle between TV and radio channels. Use u to
move the highlight to the channel list on the right of the screen. Select the channel you wish to move
or edit with pq. To mark the selected channel for deletion, press RED. Press RED again to unmark the
channel. Press OK to lock the selected channel. One more press on OK will unlock the channel again. To
move a channel to another position on the channel list, press YELLOW. Now use the pq keys to select
a new location for the chosen channel. Press OK to confirm the move. To rename a channel, press BLUE.
A banner showing a keyboard will now be displayed. Use pq tu to navigate and OK to input the
chosen character. Once finished, press GREEN to save the changes or EXIT to quit without saving.
7.3.2 Favourite
Your new receiver allows you to store channels in up to 8 favourite lists. Due to the large number of
channels available on satellite nowadays, this can be a very useful function.
Use TV/R to toggle between TV and radio channels. Select the channel you wish to add to a group with
pq. Now select the group you wish to add the channel to with FAV. Press the FAV button multiple
times to move through all available favourite groups. The following groups are available: News, Movie,
Music, Sport, Education, Life, Child and Leisure. Press OK to place the highlighted channel in the selected
favourite group. To remove a channel from a group, use pqtu to highlight the desired channel in the
group and press OK.
Once all settings are made, press EXIT to leave the menu. A confirmation banner will be shown. Press
OK to save your settings or EXIT to discard.
Note:Removing a channel from a favourite group doesn’t remove the channel from
the channel list.
7.3.3 File Explorer
The File Explorer can be used for the playback of previously recorded programs, to show photos or for
playing MP3 music files.
14
PART 1 • English
English
When the File Explorer is opened, the name of your connected USB device will be shown on the right
side of the window. Press OK or u to access the USB device. The content of the device will now be
displayed. Only files suitable for playback on your receiver will be displayed. Use pq to select a
file or folder. Press OK to start playback or to open the selected folder. To get back to the previous
folder, use EXIT or t. Alternatively you can also select the folder marked with two points “..” and
press OK.
To format the connected USB device, press the YELLOW button when in the root folder of the
connected device. Please note that the format function will only work on Hard Disk Drives.
Before disconnecting your USB device, please press the GREEN button to “Safely remove USB device”.
Warning:The Format function will delete all records, data and information from
your USB device. STRONG will not take any responsibility for damaged or
lost data on the USB device. Please make a backup copy of important data
on your USB device before using it with your receiver.
Playback of previously recorded programs
All recorded programs will be placed in the DVR folder on your USB device. Open this folder
as described above and select the desired recording. Press OK to start playback. The following
functions are available during playback: Press 2 to pause the playback. Press 2 again to resume
playback. Use 6 and 5 for fast forward or fast rewind playback. Press EXIT or 3 to get back to the
File Explorer.
Viewing photos
Your receiver allows you to watch a slide show with all photo’s available in the chosen folder. To use the
slide show: choose a folder with photo files. Press YELLOW to open the slide show settings window.
Here you can adjust the Transition mode and Duration. To disable the slideshow mode, set Duration to
Disabled. Once all settings are made, press GREEN to save and exit the Slideshow settings banner.
Select the desired Photo file and press OK to view. Press EXIT to get back to the File Explorer.
Listening to MP3 music
Select the desired MP3 file and press OK to start playback.
During playback, the following functions are available:
:
starts playback of the next MP3.
"
starts playback of the previous MP3.
3
stops playback.
5 shuffle:
All files in the directory will be played back in random order.
6 repeat:
Press once for single track repeat or twice to repeat all files.
To exit the file explorer: Use EXIT to get back to the Root directory of your USB device.
Press EXIT once more to leave the File Explorer.
Note:Please consider that File Explorer needs a correctly formatted USB device
in order to work with your receiver.
15
PART 1 • English
Playback of MP3 music will continue as long as the File Explorer is active. This allows you to listen to MP3
music while watching photos.
Tip:The File Explorer will only show files when a correctly formatted USB device is
connected to the receiver.
7.3.4 Timer
Timers can be used to schedule recordings or to switch to a certain channel at a desired moment. It will
help you not to miss your favourite events.
Use pq to select one of the eight available timers. Press OK to advance. The Edit Timer screen will now
be displayed. Use pq to switch between settings and tu or [0~9] to adjust the value of a setting.
Cycle:
Choose between Once, Everyday or Weekly.
Date:With Cycle set to Once: press OK to display the calendar. Use pqtu to pick
the date for the recording and confirm with OK.
With Cycle set to Weekly: Use tu to select the day of the week at which the
timer will start.
Time:Use the [0~9] buttons to enter the time at which the timer will start.
Action:Use tu to choose between Play or Record. Select Record to set a timed recording.
Channel:Press OK to display the channel list and use pq to select the channel that the
receiver should use for the timed action.
Duration:Use the [0~9] buttons to digit the duration of the timer.
Once all settings are made, press EXIT to leave the menu. A confirmation banner will be shown. Press
OK to save the timer or EXIT to discard.
Deleting a timer
In order to delete a set timer, select it with pq and press RED. A confirmation banner will now be
shown. Press OK to delete or EXIT to cancel.
Note:In case one timer is in conflict with another or if the set time has already passed,
the receiver will display a warning and asks you how to solve the conflict.
7.4 Advanced
This sub menu gives you access to advanced functions such as updating and factory reset. The following
options are available: System Info, USB Update, OTA and Factory Reset.
7.4.1 System Info
Displays valuable information about the software and hardware version of your receiver and our web
address www.strong.tv . A customer support agent might ask for the information given in this screen.
Press EXIT to leave the System Info screen.
7.4.2 USB Update
This function allows you to perform a system upgrade from an USB device. You can also use it to export
your channel list to a connected USB device.
16
PART 1 • English
Exporting channel data
To export all channel data, enter USB Update and press BLUE. Follow the directions on screen. This
function requires a correctly formatted USB storage device to be connected to the receiver.
English
Software upgrade
The software files should be placed in the root directory of the device. Connect the USB device to
the receiver and enter USB update. An attention banner will now be displayed. Press OK to start the
update.
Warning:NEVER power off the receiver or remove the USB device during the
software update process. Doing so might cause irreparable damage to
your receiver and will void your warranty.
7.4.3 OTA
The OTA (Over the Air) function allows you to search for software updates available on satellite.
Please ask your local Strong dealer or visit our website for according information.
In the OTA menu make all necessary settings (Satellite, Frequency, Polarisation and Symbolrate) and
press GREEN to start the update process.
Warning:NEVER power off the receiver or pull the mains plug during the software
upgrade process. Doing so might cause irreparable damage to your
receiver and will void your warranty.
7.4.4 Factory Reset
A factory reset will restore your receiver to the factory default settings. To reset the receiver, you have
to enter your PIN code (Default PIN:0000). After the reset, the receiver will start up in the Setup
Wizard.
Warning:A factory reset will permanently delete all your personal settings, timers and
stored channels. Please consider this before you perform a factory reset.
7.5 Games
Your receiver is equipped with 4 games.
To play a game, select one of the four available games (Sudoku, Tetris, Snake or Box) and press OK to
enter the game. Please follow the directions on screen.
8.0 TROUBLESHOOTING
There may be various reasons for abnormal operation of the receiver. Please check the receiver
according to the procedures shown below. If the receiver does not work properly after checking
it, please contact your local Serviceline or STRONG dealer. Alternatively you can send a support
mail via our website: www.strong.tv. NEVER open or disassemble your receiver. This may cause a
dangerous situation and will void the warranty.
17
PART 1 • English
Symptom
The display on front
panel does not light
up.
Cause
The power cord is not plugged in.
Remedy
Check that the power cord is plugged
in to the wall outlet. Make sure power
switch on rear panel is in ON position.
Receiver switched to STBY and the
display function is switched OFF.
Check if receiver is in STBY and the
setting within the menu Setup>Time
Setting>Time Display is set to OFF
Wrong connection or setting of the
Audio/Video output of the receiver
to TV.
The batteries of the remote control
are not inserted, wrongly inserted or
exhausted.
The USB storage device Wrong formatted.
is not working properly.
The external USB
Power consumption is too high.
HDD does not start.
Connect the Audio/Video output of
the receiver to TV correctly and check
the adjusted settings in the menu
Setup> Output Options.
Press the MUTE button.
Turn TV on.
Check the antenna cable, replace the
cable, or connect the cable to the
receiver tightly.
Set the values of tuner parameters
correctly in menu Installation>
Satellite Settings.
Check the signal strength with a
spectrum analyzer and adjust your
dish correctly.
Check whether the batteries are inserted
correctly or exhausted, if so replace the
batteries in the remote control.
Format USB device by receiver in
menu Channel>File Explorer.
Connect an extra power supply
adapter to your USB HDD device.
The receiver switches Auto Power Down function is
to STBY automatically. activated and reached the adjusted
time (default 3h).
In the menu Setup>Time Setting you
can adjust the Auto Power Down time
or disable it.
No picture or sound
No picture
Audio muting.
TV power off.
The receiver can’t receive the signal.
Incorrect values of some tuner
parameters.
Wrong direction of the dish.
The remote control
does not work
18
PART 1 • English
9.0 SPECIFICATIONS
English
Demodulator
Demodulation:QPSK, 8 PSK
Input Symbol Rate:DVB-S QPSK:1~45 Ms/s
DVB-S2 8PSK/QPSK:10~30 Ms/s
FEC Decoder:Auto,1/2, 2/3, 3/4, 5/6, 7/8 in DVB-S mode;
1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10 in DVB-S2 mode
2/3, 3/5, 3/4, 5/6, 8/9, 9/10 in DVB-S2 8PSK mode.
Video Decoder
Profile Level:MPEG-2 MP@ML, MP@HL, MPEG-4 H.264/AVC
Input Rate:Max. 90 Mbit/s
Aspect Ratio:4:3, 16:9, Pan & Scan, Letterbox, Combined
Frame Rate:25 Hz for PAL, 30 Hz for NTSC
Video Resolution:576p, 720p, 1080i
Audio Decoder
Audio Decoding:MPEG-1 Layer 1&2, MPEG 4 H.264 AAC, AC3 Downmix
Audio Mode:Mono L/R, Stereo, AC 3
Frequency Response:20 Hz~20 kHz, <+/-2 dB
60 Hz ~ 18 kHz <+/- 0.5 dB
Sampling Rate:32, 44.1, 48 kHz
Tuner
Connector:1xF Type , IEC169-24, Female
Input Frequency Rage:950-2150 MHz
RF Impedance:75 Ohm unbalanced
Signal Level:-75 to -25 dBm
LNB Power:13 / 18 V DC (+/-5%)
Max. 0.5 A max, overload protected
DiSEqC Versions:1.0, 1.1, 1.2, GOTO X, Tone Burst.
System & Memory
CPU:STi7111
Flash Memory:
8 MBytes
System Memory:256 MBytes
19
PART 1 • English
Connectors
SAT IN; SAT OUT
TV SCART (RGB, CVBS, Audio L/R Output with volume control)
HDMI (V/A-Output) Type A Version 1.0 HDCP 1.1
RCA Output - Audio L/R & Video Output
S/PDIF Out (Coaxial, Optical)
IR Extender input
USB 2.0, Type A Connector
05 Jul 2013 18:21
General Data
Input Voltage Range:100 - 240 V AC, 50/60 Hz
Power Consumption:max. 20 W, typ. 7.1 W (without external device)
Power consumption in stand-by:
0.83 W (without external device)
Operating Temperature:0° ~ +40°C
Storage Temperature:-10° ~ +70°C
Operating Humidity Range: 25 - 75%, RH, non-condensing
Size (W × H × D) in mm:230 x 168 x 40
Weight:0.78 kg
20
Open as PDF
Similar pages