OPERATING INSTRUCTIONS - Tanning-Bed

04.09.2006
14:32 Uhr
Seite 1
ERGOLINE AFFINITY
1001700
1001700.qxd
OPERATING INSTRUCTIONS
SUN ERGOLINE, A DIVISION OF JK-PRODUCTS & SERVICES, INC.
2905 Northwest Blvd., Suite 40 . Plymouth, MN 55441, USA
E-Mail: ergoline@sunergoline.com · Fax: 763.551.3607
Phone: 888.771.0996 · Website: www.sunergoline.com
Ergoline AFFINITY
1000516-00- / us / 09.2006
AFFINITY 500 Turbo Power
AFFINITY 600 Turbo Power Air Condition
AFFINITY 800 Turbo Power Temptronic
OPERATING INSTRUCTIONS
Identify your tanning device . . . . . . . . . . . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2
Identify your tanning device
Customer Service
For contact with Customer Services, please write down
the device number of your tanning device.
5
Global Service USA
A Div of JK Products & Services, Inc.
#1 Walter Kratz Drive
Jonesboro, AR 72401
800-445-0624
870-935-9046
e-mail: support@jkamerica.com
http://support.jkamerica.com
3
Skin types
Skin types
Tanning times
For the recommended exposure schedule (see page 5).
Skin type I (Sensitive):
Invariably gets sunburn, accepts little natural sunlight and does not tan.
Skin type II (Fair):
This is the individual that usually burns easily and severely, tans
minimally or lightly and peels.
Skin type III (Average):
Often referred to as “Average” complexion, burns moderately and tans
about average.
Skin type IV (Brown):
This individual burns minimally, tans easily and above average with each
exposure.
Skin type V (Dark Brown):
This individual’s system rarely burns, tans easily and substantially.
4
Tanning times
Tanning times
Note:
Description of skin types see
Page 4.
07270 / 0
“This product is in conformity with performance standards for sunlamp products under CFR21 Part 1040.”
5
Foreword
Foreword
Dear Customer,
The Ergoline device you have purchased is a technically advanced and
powerful product. Your device was manufactured with the greatest care
and precision. It went through numerous quality and safety checks in order to guarantee trouble-free, safe operation. Nonetheless, you can also
make a significant contribution to your long-term satisfaction with your
device. Following the tips and instructions in the instruction manual will
ensure you enjoyment and pleasure with your device.
If you have any questions, we are always available to answer them.
Yours sincerely
JK-Products, Inc.
1) (800) 643 0086
6
1)
• Read and observe the information in this instruction manual. This will
enable you to prevent accidents and provide you with a reliable device ready for use.
• Always observe current legal and other regulations and legal requirements as well as the applicable environmental protection regulations.
Note:
We reserve the right to make technical changes to the illustrations and specifications in this instruction manual.
Reprinting and reproduction, in whole or in part, of this manual is only permitted with our previous written approval and
with the source specified.
Table of Contents
Skin types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operation: overview AFFINITY 800 . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Tanning times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Important safety notes and information. . . . . . . . . . . . . . . . . 9
Safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Obligations of the studio operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Instructions pertaining to a risk of fire, electric shock, or injury . . . . . . 11
Instructions pertaining to a risk of damage to the machine . . . . . . . . . 13
Meaning of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Environmental protection information . . . . . . . . . . . . . . . . . . . . . . . . . 20
Use the sunbed – but use it properly! . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
To interrupt tanning session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Settings during start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Running time of accent lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
IR function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Regulating facial tanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Switching shoulder tanner off and on1) . . . . . . . . . . . . . . . . . . . . . . . . 33
AFFINITY 800: Regulating Temptronic . . . . . . . . . . . . . . . . . . . . . . . . 34
AFFINITY 600: Switching air condition off and on . . . . . . . . . . . . . . . 36
Regulating body cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Regulating facial cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
AFFINITY 800: Switching AROMA RELAX or VITAL on and off. . . . . 39
AFFINITY 800: Switching AQUA MIST body nozzle on and off . . . . . 40
AFFINITY 800: Switching AQUA MIST head nozzle on and off . . . . . 41
Voice Guide1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
INFO text1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Selecting music channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Operation: overview AFFINITY 500/600 . . . . . . . . . . .Fold-out page 24
1) optional
7
Table of Contents
Table of Contents
Table of Contents
Adjusting volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table of Contents
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Cleaning filter mats in the canopy. . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Cleaning filter mats in the shoulder tanner . . . . . . . . . . . . . . . . . . . . . 86
Maintenance instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
AFFINITY 600/800: Temptronic/Air Condition: cleaning/replacing filter
and filter mat, emptying condensate container . . . . . . . . . . . . . . . . . . 88
De-energize device and secure against being switched on again. . . . 51
AFFINITY 800: AROMA system: replacing aroma container . . . . . . . 91
Maintenance: overview AFFINITY 500/600 . . . . . . . . .Fold-out page 52
AFFINITY 800: AQUA MIST system: replacing canister . . . . . . . . . . 93
Maintenance: overview AFFINITY 800 . . . . . . . . . . . . . . . . . . . . . . . . 53
Presettings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Cleaning intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Maintenance intervals, installed lamps and order numbers. . . . . . . . . 55
Relamping/maintenance instructions. . . . . . . . . . . . . . . . . . . . . . . . . . 61
Changing presettings with the control panel. . . . . . . . . . . . . . . . . . . . 96
Changing presettings with a hand-held unit . . . . . . . . . . . . . . . . . . . . 98
Cleaning/replacing UV low-pressure lamps in sunbed base . . . . . . . . 62
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Cleaning/replacing UV low-pressure lamps in shoulder tanner . . . . . . 64
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Cleaning/replacing UV low-pressure lamps in side section . . . . . . . . . 66
Cleaning/replacing UV low-pressure lamps in canopy . . . . . . . . . . . . 68
Cleaning/replacing interior lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Cleaning/replacing UV high-pressure lamps and filter panels in
the side section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cleaning/replacing UV high-pressure lamps and filter panels in the
canopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Cleaning/replacing accent light in the canopy . . . . . . . . . . . . . . . . . . . 79
Cleaning/replacing accent light in the frontpanel . . . . . . . . . . . . . . . . . 81
Option: Cleaning/replacing ambient lights . . . . . . . . . . . . . . . . . . . . . . 82
Cleaning filters in the sunbed base . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
8
JK-Products, Inc. – Limited Warranty . . . . . . . . . . . . . . . . 107
Timer operation – see manual “Intellitan Remote Timer”,
Order no. 801129-..
Please read and observe ...
Important safety notes and information
Description of warning signs
Danger notices, damage to persons:
Type and source of danger, e.g. “DANGER – High voltage!”
Description of the consequences, e.g. “You can be killed or
DANGER! injured by an electric shock!”
Countermeasures:
– Disconnect device from power supply before opening.
Caution notices, damage to property:
Caution!
The word “Caution” with this label points out that danger for
devices, materials and the environment can be expected
here.
Important information:
Note:
This symbol does not identify safety notices, but states information for a better understanding of the processes.
– Do not reach into the inside with the device switched on.
Warning notices, damage to persons:
Type and source of danger, e.g. “Warning – hot surface!”
Description of the consequences, e.g. “You can burn your
WARNING! hand (skin, face)!”
Countermeasures:
– Do not touch hot parts and nearby surfaces.
– Wait until hot parts and surfaces have cooled down.
9
Safety notes
Safety notices
Safety notes
Please read and observe ...
Intended use
Obligations of the studio operator
The tanning device is intended exclusively for cosmetic tanning of the human skin.
• As the operator you are responsible for informing users on possible
risks during tanning.
• The device is meant for commercial use only, not for home use.
• This device is used for tanning one adult person at a time.
• All danger and safety labels attached to the device must be observed!
Do not remove them!
• The user wears suitable eye protection that blocks UV radiation during tanning.
• No safety equipment (e.g. panel switch) may be removed or deactivated which can impair the safe operation of the device!
Any other use shall be considered improper. The manufacturer cannot be
held liable for damage or injuries resulting from this. The operator bears
the sole risk for this.
• The device may only be operated in a serviceable condition!
The proper use also includes compliance with the manufacturer’s instructions, operating and maintenance conditions. This device may only be
operated, maintained and repaired by persons familiar with these tasks
and who have been informed of the dangers involved.
10
• The operator is bound to ensure that the equipment is handled correctly.
Please read and observe ...
Instructions pertaining to a risk of fire, electric shock, or injury
You can be killed or injured by an electric shock!
Assembly and electrical connection must comply with naDANGER!
tional and local regulations.
– The device may only be assembled, installed, upgraded
or repaired by specially trained and instructed personnel.
WARNING – ultraviolet radiation!
WARNING!
Unprotected tanning may result in eye injury and eye diseases.
The unprotected eye can become inflamed on the surface,
and in certain cases the retina can be damaged by excessive radiation. Cataracts can form after frequently repeated
exposure to radiation.
– Inform users to use the included protective goggles
that block UV (Order No. 84592-..).
WARNING – ultraviolet radiation! Follow instructions!
Failure to use protective eyewear may result in severe
burns or other eye injury. If discomfort develops, discontinWARNING! ue use and consult a physician.
– A person who does not tan in the sun most likely will not
tan from the use of this device. Persons with very sensitive skins (skin type I) must not use the unit, as with this
skin type tanning is impossible without damaging the
skin (e.g. sunburn).
– Individuals with acute sunburn, individuals who have
had or have skin cancer, or individuals who are at increased risk of skin cancer, must not use the system.
– UV devices must not be used without taking medical advice if unexpected effects, such as itching, occur within
48 hours of the first session.
– The sunbed must never be used if a filter panel is missing or damaged, or the timer is defective!
– UV light from the sun or UV systems can cause injuries
to the skin or eyes. This biological effect is dependent
on the sensitivity of the individual's skin and on the type
and amount of UV light.
– As with natural sunlight, overexposure can cause eye
and skin injury, sunburn, and allergic reactions.
11
Safety notes
DANGER – High voltage!
Please read and observe ...
Safety notes
– Repeated exposure may cause premature aging of the
skin and skin cancer.
– Medications or cosmetics applied to the skin, may inWARNING!
crease sensitivity to ultraviolet light.
– A person having a history of skin problems should consult a physician before use.
WARNING – ultraviolet radiation!
Danger of long-term consequences.
WARNING! – Overexposure should be avoided.
– The elderly should not use this equipment.
– Nursing infants and small children through age 7 years
may not use this device.
– The following applies to minors under the age of
18 years: Only use tanning devices in agreement with a
parent or guardian, or after consulting a physician.
– While there is no immediate clinical evidence of UVA exposure and its effects upon expectant mothers, it is
strongly advised that expectant mothers be discouraged
from using the tanning unit.
12
WARNING – risk of infection!
Infections can be transferred through skin contact.
WARNING! All items/equipment components, with which the user can
come into contact during tanning, must be disinfected after
every tanning session:
• Protective goggles
• Headrest
• Acrylic sunbed
• Handles and control panel
Please read and observe ...
Occasionally, persons using the tanning device will experience a slight reddening of the skin – usually in small patches – after the second or third session. This redness is often
accompanied by an itching sensation. This may be nothing
more than a heat “rash” caused by heat from the lamps
within the device. It is generally very limited and caused by
constant contact of the skin with the acrylic surface. It
should go away within approximately 24 hours and should
not reappear. This rashing can be lessened or prevented by
applying moisturizer lotion to the affected area after the tanning session is completed.
– Follow instructions.
Instructions pertaining to a risk of damage to the
machine
CAUTION – danger of overheating!
Danger of overheating by obstruction of the air routing.
– Do not change, obstruct or block the air inflow and outflow area to the device or make any unauthorized
changes to the device. The manufacturer shall bear no
liability for damage or injuries resulting from such actions.
– Before putting a tanning device into operation, the transport pallet must be removed from under the device.
Danger of overheating by obstruction of the air routing.
– The time between the first two tanning sessions must be
at least 24 hours.
– Increasing tanning also requires an extension of the exposure time (= radiation time) or after a certain degree
of tanning has been achieved, a further intensification is
not possible. However, the radiation time may not be extended as desired within the scope of the permissible radiation doses! Therefore, only a certain degree of final
tanning dependent on the skin type can be achieved
without endangering your health.
– Inform users about proper tanning.
13
Safety notes
Note:
Please read and observe ...
Meaning of symbols
Symbols
General symbols
Filter panels
Inform Customer Services
Cleaning and disinfectant agents
Ergoline key
Part/item number (for orders)
Do not touch, hot surface!
14
Operation
Suction cup
Display of tanning time
Low-pressure lamp(s)
Display of run-on time (fan run-on)
UV low-pressure lamp(s)
Fault display (example),
see separate manual
Starter for low-pressure lamp(s)
Display of Info Track 1 (from 1-17)
UV high-pressure lamp(s)
Display of Music Channel 1 (Channel 1)
Factory setting: 1 channel
Customer service can set up to 7 channels
Please read and observe ...
e.g.
2s
0-3 min
Headphone connection
Description
Technical Data
Accent lights
Maintenance
Symbols
Display when adjusting volume
Body cooling by
AQUA SOLAR WITH SKIN+ ADDITIVE
Caution, safety switch!
Aroma “Relax”, “Vital”, “Cabin”
Unscrew/release screw
Press button
Tighten/lock screw
Press button for 2 seconds
Cleaning
Duration: 3 minutes
Replacing
Loudspeaker
Clean or replace depending on soiling
15
Please read and observe ...
Guidelines / Export / …
Draining
Air condition / Temptronic
Visual inspection
Filter/filter mat
Filter and filter mats must not be damp.
...
Continuation of work steps on next page
End of work step
Presettings
Troubleshooting
16
Guidelines
This device was built conforming to UL STD 482, and is certified to CAN/
CSA STD C22.2 2 No. 224.
Export
We would like to point out that these devices are exclusively intended for
use in the USA and Canada and may not be exported to other countries
and operated there! The manufacturer assumes no liability whatsoever
in the event of non-compliance! We explicitly emphasize that high liability
risks may occur for the exporter and/or the operator in the event of noncompliance.
Please read and observe ...
The equipment of the devices differs depending on the model.
In this instruction manual all standard and optional components/functions
are taken into account which must be observed during operation and/or
when performing maintenance.
The control panel is also affected by the differing equipment: Only those
buttons are visible that can be operated, i.e. the corresponding function
must be part of the equipment of the device.
Accessories
Some accessory parts are taken into account in the maintenance schedule beginning on Page 54, however this does not automatically mean that
your device is provided with this equipment.
An overview of the possible accessories is provided in the sales documentation and the planning manual. See page 26 for a selection of these.
Product information
Acrylic glass panels
The acrylic glass panels for the tanning devices are produced of acrylic
glass developed especially for this application. The acrylics used are
characterized by a particularly high UV permeability and resistance, as
well as an easy-care, hygienic surface that is gentle to the skin.
The acrylic glass panels are formed to their shapes for the specific devices in a technically complex production process. Despite state-of-the-art
production know-how, the presence of minor spots, air bubbles or
streaks in the acrylic panels is unavoidable. In addition, microfine hairline
cracks can occur on the bed surface during operation.
These occurrences are material-dependent and are unavoidable in processing, however have no significant effect on the use or value and can
therefore not be recognized as defects.
CAUTION!
Cosmetics or sun screen products must be removed prior to
using the sunbed as they can cause damage (e.g. fine
cracks on the surface) when used continuously.
17
Product information
Equipment
Please read and observe ...
Maintenance and care
Maintenance and care
Extreme danger! High voltage!
DANGER!
During maintenance work there is a risk of touching live
parts and receiving a fatal electric shock.
– Disconnect device from power supply before opening –
also see Page 51.
– Do not reach behind covers and do not open the device
with the device switched on.
– Refit any safety devices (e.g. switches) after the work
has been completed.
Maintenance and care play a major role in deciding whether the device
meets the requirements placed on it in a satisfactory manner. The compliance with the specified maintenance intervals and the careful conducting of the maintenance and care work are therefore absolutely necessary
– see Page 52.
The current operating hours of the parts requiring maintenance can be
displayed in the Presetting mode – see Page 96 ff.
CAUTION!
Only use genuine spare parts of the same type!
The use of other parts may limit or void your manufacturer’s
warranty!
Any liability is excluded in case of damage or injury proven
to be the result of the use of non-genuine spare parts.
18
Please read and observe ...
Cleaning
CAUTION!
Do not rub with a dry cloth – danger of scratching!
For fast, hygienic proper cleaning of acrylic glass surfaces,
use a specially developed fast disinfectant cleaner.
Other cleaning agents, especially concentrated disinfectants or solvents (e.g. Lysoform, ethyl alcohol or other liquids containing alcohol) must never be used for cleaning.
Failure to observe this voids all warranty claims.
Plastic surfaces
For cleaning the other plastic surfaces, it is best to use warm water and
a leather cloth. Never use aggressive cleaning agents containing alcohol
or essential oils. These may lead, in the long run, to damage not covered
by the warranty.
During cleaning, a slight discoloration of the leather cloth by the rubber
seals must be expected for production-related reasons.
Note:
Prevent damage to plastic surfaces. Remove rings, watches, bracelets etc. before the start of cleaning work.
02756 / 0
19
Cleaning
Acrylic glass surfaces
Please read and observe ...
Environmental protection
information
Environmental protection information
Environmental Declaration – The JK Corporate Group
The JK corporate group is subject to the strict regulations of EC Directive
761/2001 and the ISO 14001 standard, and undergoes regular internal
and external environment audits performed by trained auditors.
Environmental regulations – disposal of lamps
UV low-pressure lamps and UV high-pressure lamps contain fluorescent
materials and other waste containing mercury.
According to the national waste disposal laws and in accordance with the
municipal waste regulations, proof must be provided of the proper disposal of UV lamps.
Your local environmental agency will be happy to assist you with the disposal of UV lamps.
Packaging
All packaging consists of 100 % recyclable materials.
Disposal of recyclable materials
The device has been produced of recyclable materials. When being
scrapped later, the device must be disposed of properly. Sun Ergoline
will provide you with information on the content or potential hazards of
the materials used.
20
Please read and observe ...
A few things need to be noted to get maximum enjoyment from a sunbed.
Here are some answers to some frequently asked questions.
Make-up on the sunbed?
Please remove make-up or don't use make-up while tanning. Clean skin
absorbs UV light better.
A wide variety of ingredients are found in cosmetics. Again, whether
these are emulsifiers, greases, or so-called scents – in conjunction with
UV radiation, these can cause allergic reactions of the skin.
Accordingly, a must before using a sunbed is: Remove all make-up. This
is essential. Make-up clogs the pores in the face. The UV light from a
sunbed re-opens these clogged pores so that not only does the light penetrate the skin, but also the allergenic components of the make-up.
A further negative consequence of make-up is that the appearance of the
skin deteriorates irreversibly over a period of time. However good a decent make-up might be – in conjunction with UV light, it causes more
harm than good. Therefore: Remove all make-up before a session on
your sunbed – it will be much better applied afterwards.
Are medications and the sunbed compatible?
It is known that some medications increase the skin's sensitivity to UV
light. This probability is particularly high with antibiotics, sulphonamides,
psychiatric drugs, tranquillizers, anti-diabetes treatments and diuretics.
Sun creams which contain psorale or kumarin also increase skin sensitivity. If you are in any doubt, first ask your doctor - then you can enjoy
the sun at no risk.
Contact lenses on the sunbed?
The answer is: Yes! Like any other sunbed user, contact lens wearers
should also wear special protective goggles which protect the eyes
against UV radiation. To guarantee better protection, wearers of spectacles and contact lenses can ask their optician for exchange contact lenses with UV protection. The UV-A and UV-B filters built into exchange
contact lenses will protect the cornea and the internal parts of the eye
against almost 100% of the energy in UV radiation.
This will benefit sunbed users not only in the open air, but on the sunbed
itself. For more information, ask your optician or optometrist.
Showering after leaving the sunbed?
The browning is in the skin, not on it. Therefore you cannot wash it off.
Treat your skin to a moisturizing cream after showering.
21
Use the sunbed properly
Use the sunbed – but use it properly!
Use the sunbed properly
Please read and observe ...
22
Operation
Operation
Mandatory reading
• to use provided UV-blocking protective eyewear whenever the equipment is energized.
When describing the operation, the tanning device is often
shown with the canopy open. During tanning the canopy
must always be closed.
Proper operation is not possible with the canopy open.
• to follow the exposure schedule in accordance with their skin type.
Failure to do so may result in overexposure.
A tanning system is not a toy. You cannot vary the strength of the lamps
in your unit.
Should you have any questions regarding the proper use of your tanning
system, contact Global Service USA at:
800 445 0624
7:00 a.m. to 7:00 p.m. (CT)
Warning – ultraviolet radiation!
Danger of skin injuries and skin diseases!
• The sunbed must never be used when a filter panel is
WARNING! missing or damaged, or the timer is defective!
23
Operation
Inform users
Please open this fold-out page.
Note:
Operation
Always read and follow all instructions for proper usage prior to allow
anybody using a tanning device. The operating instructions included with
this device must always be followed to prevent possible injuries or to reduce them to a minimum.
Optional:
AFFINITY 500 Turbo Power / AFFINITY 600 Turbo Power Air Condition
AFFINITY 500 Turbo Power
AFFINITY 600 Turbo Power Air Condition
98
AFFINITY 800 Turbo Power Temptronic
only AFFINITY 600
98
08512 / 0
24
Operation
AFFINITY 800 Turbo Power Temptronic
98
98
25
Operation
Accessories
26
Tanning
Start of tanning
The device is started automatically with an internal or external timer.
Note:
Operation
Timer instructions: see separate manual1).
Preparation time
Before the UV lamps turn on, you have a few minutes to prepare yourself.
During the preparation time you can switch on the UV lamps at any time
by pressing the START/STOP button.
– Remove your clothes and all jewelry.
– Remove make-up and other cosmetics.
– Remove glasses. Contact lenses can be worn under the protective
goggles.
– Put on the protective goggles.
– Lie down on the bed surface.
– Close the canopy.
– Press the START/STOP button.
...
1) Order no 801129-..
27
Interrupt or end tanning session
AFFINITY 500: Settings during start-up
The tanning session ends automatically after the preset time has run
down. The internal fan continues to run for approx. three (3) minutes to
sufficiently cool the device.
– To interrupt a tanning session, press button START/STOP anytime
during a session.
Operation
– Press START/STOP again to restart the lamps.
optional:
...
28
AFFINITY 800 Temptronic: Settings during start-up
Operation
AFFINITY 600 Air Condition: Settings during start-up
optional:
optional:
29
Stand-by
IR Function
Operation
Running time of accent lighting
The accent lights are automatically switched
on at the end of the tanning session after the
set operating time and are switched off again at
the beginning of the next tannings session.
The running time of the accent lights in the
Standby mode can be changed with the presettings – see from Page 96 on.
96
30
Regulating facial tanners
1
2
3
Operation
1
Press for two (2) seconds.
Switching the facial tanners OFF:
– Press button
1
for two (2) seconds.
Switching the facial tanners on again:
2
2
– Press button
. It takes approx. one (1)
minute until the facial tanners reach their
full output.
Adjusting the intensity:
– Press button
.
– While the button
flashes, press + or –
to adjust the intensity of the facial tanners.
...
31
1 min
Operation
4
One (1) minute delay.
5
+ 1 min
32
Optional
Switching shoulder tanner off and on
Press for two (2) seconds.
Operation
1
2
33
AFFINITY 800 Turbo Power Temptronic
Temptronic – Adjust coolness
1
2
3
Operation
1
Press for two (2) seconds.
1
During start-up the lightlevel of 8 is active.
– Press button
(Temptronic).
While the button flashes, press the plus or minus button to change the cooling intensity.
2
2
Switching Temptronic OFF:
– Press button
for 2 seconds.
Switching Temptronic on again:
– Press button
again. It takes approx.
3 minutes until the cooling effect of the air
condition is reestablished.
34
...
AFFINITY 800 Turbo Power Temptronic
Three (3) minutes delay.
Note:
If the automatic climate control
(Temptronic) fails, the sunbed will be
cooled without any control. In this
case, the user can only switch the
cooling on and off.
Operation
4
5
35
AFFINITY 600 Turbo Power Air Condition
Air condition – Switching off and on
Press for two (2) seconds.
3
Operation
1
Three (3) minutes delay.
During start-up the air condition is active.
Switching the air condition OFF:
– Press button
for 2 seconds.
Switching the air condition on again:
– Press button
again. It takes approx.
3 minutes until the cooling effect of the air
condition is reestablished.
36
2
Surround cooling body ventilator – Adjust
speed
1
2
1
2
Operation
1
– Press button
.
2
– While the button flashes, press the plus or
minus button to change the intensity of the
air stream.
37
Surround cooling head nozzles – Adjust
speed
1
2
1
2
Operation
1
– Press button
.
– While the button flashes, press the plus or
minus button to change the intensity of the
air stream.
38
2
Switching AROMA RELAX or VITAL on and
off (Example: RELAX)
1
Press to activate.
3
Operation
1
2
The AQUA MIST AROMA system includes aromas with the scents “Relax” and “Vital”, which
are distributed via the head nozzles.
A third aroma “Cabin” is distributed in the cabin
(no operation possible).
Press button
(or
1
2
2
Press for two (2) seconds.
4
).
Together with the aroma, AQUA MIST (see
Page 40) is also switched on for the face and
body.
While the button (RELAX or VITAL) flashes,
press the plus or minus button to change the intensity of AROMA and AQUA MIST.
39
Switching AQUA MIST body nozzle on and
off
1
Press to activate.
3
Operation
1
The AQUA MIST function sprays a fine mist of
AQUA SOLAR WITH SKIN+ ADDITIVE in the
interior of the sunbed for body cooling.
– Press button
.
– While the button flashes, press the plus or
minus button to change the intensity of
AQUA MIST body.
40
1
2
2
4
2
Switching AQUA MIST head nozzle on and
off
1
Press to activate.
3
Operation
1
2
1
The AQUA MIST function sprays a fine mist of
AQUA SOLAR WITH SKIN+ ADDITIVE in the
interior of the sunbed for face cooling.
– Press button
2
2
4
.
– While the button flashes, press the plus or
minus button to change the intensity of
AQUA MIST head.
41
Voice Guide
1
…
…
Operation
…
…
…
…
…
2
…
…
…
…
…
…
42
Info text
1
Press 5 s to
activate.
3
Operation
1
2
1
When you press the
on tanning are played.
– Press button
button, general texts
2
Press for two (2) seconds.
2
4
for 5 seconds.
– While the button flashes, press the plus or
minus button to change between info
tracks.
43
Selecting music channel
Press to activate.
2
1
2
3
Operation
1
1
1
– Press button
.
– While the button flashes, press the plus or
minus button to change the channel.
means: no Channel selected, there is
no sound, music is “OFF”.
44
2
2
4
Adjusting volume
1
Press to activate.
3
Operation
1
2
96
1
– Press button
.
2
2
– While the button flashes, press the plus or
minus button to change the volume.
45
Technical data
Ergoline AFFINITY 500
Turbo Power
Ergoline AFFINITY 600
Turbo Power Air Condition
Ergoline AFFINITY 800
Turbo Power Temptronic
12100 W
13700 W
17000 W
Rated voltage:
230V
230V
230V
Rated frequency:
60 Hz
60 Hz
60 Hz
40 amp 3-pole or
80 amp 2-pole
50 amp 3-pole or
80 amp 2-pole
50 amp 3-pole or
80 amp 2-pole
Model:
Rated power consumption:
Technical
Data
Rated fusing:
Conformity mark:
46
Powerinput 1-pole
(max. 90 amp)
230V AC 60 Hz
Technical
Data
Powerinput 3-pole
(max. 50 amp)
230V AC 60 Hz
04045 / 1
47
Technical
Data
B
A
Bed tolerance in room
C
03411 / 1
AFFINITY 500/600
68 1/2 in
A =
52 3/4 in
B =
C =
55 7/8 in
D =
78 3/4 in
E1 =
89 in
E2 =
92 1/2 in
F
=
31 7/8 in
?
=
300 lb
8 ft
BK =
TK =
7 1/2 ft
48
1740 mm
1340 mm
1420 mm
2000 mm
2260 mm
2350 mm
810 mm
135 kg
2400 mm
2300 mm
AFFINITY 800
73 1/4 in
A =
53 9/16 in
B =
C =
60 1/4 in
D =
78 3/4 in
E1 =
89 in
E2 =
92 1/2 in
F
=
35 7/16 in
?
=
300 lb
8 ft
BK =
TK =
7 1/2 ft
1860 mm
1360 mm
1530 mm
2000 mm
2260 mm
2350 mm
900 mm
135 kg
2400 mm
2300 mm
Maximum room temperature / Humidity
Acoustic level during tannig
AFFINITY 800
1m
LpA
< 81 dB (A)
68,9 dB (A)
07393 / 0
07394 / 0
AFFINITY 500/600
1m
LpA
1m
67,2 dB (A)
08587 / 0
07394 / 0
49
Technical
Data
1m
50
Technical
Data
Maintenance instructions
De-energize device and secure against being switched on again
Extreme danger!
• A strip of adhesive tape with the wording
"DANGER do not switch ON!" may be applied
over the actuation levers of circuit breakers
which cannot be removed.
If work is to be performed on the devices,
they must be powered off. That means that
DANGER! all live lines must be switched off.
Switching off the device alone is insufficient,
as certain points may remain energized.
Therefore, switch off and lockout circuit
breakers before performing any work.
Please open this fold-out page.
01510 / 1
Severe accidents can occur if the device is mistakenly
switched on again.
DANGER! Immediately after powering off, secure all switches or fuses
used for power against being switched on again.
A prohibition sign with the text:
“Work in progress!”
• “Place: ..............................”
• “Sign may only be removed by: ............”
must always be securely mounted immediately.
Extreme danger!
01511 / 1
Prohibition signs must not be hung on or touch live parts.
DANGER!
51
Maintenance
Extreme danger!
Maintenance
04049 / 0
AFFINITY 500 Turbo Power
AFFINITY 600 Turbo Power Air Condition
52
Maintenance
AFFINITY 800 Turbo Power Temptronic
53
Scheduled cleaning
Note:
Clean after every use.

WARNING – risk of eye irritation!
Protective goggles may only be cleaned with an approved disinfectant.
Maintenance
WARNING!
-

Note:
Clean/drain if necessary!

54

/50 h

4x
51937-..
83

2x
800601-..
85

1x
51975-..
88

1x
51937-..
88
1)
2x
800278-..
86
Maintenance
Scheduled cleaning – filters, filter mats
1) = Shoulder tanner, optional
55
Scheduled maintenance – AROMA, AQUA MIST
6000 ml
Maintenance

1)

300 h

a) b) c)
1) Intervalls, see «AQUA SYSTEM Product Information»
(Order-Number 801 610).
56
365 2603
100 ml
a) Relax: 365 2003
b) Vital: 365 2103
c) Cabin: 365 2203
93
91
1,000 h
a)
2x
blue
36 W
11792-..
79
b)
1x
blue
58 W
12063-..
81
c)
2x
blue2)
18 W
11797-..
82
d)
1x
blue
30 W
11377-..
70
a) b)
d)
4x
S10
10 047-..
70, 79, 81
c)
2x
S2
10 013-..
82
1) Standard equipment: blue lamps.
More colors are available from Global Service USA, see Page 5
2) optional
57
Maintenance
Scheduled replacement – accent lights1)
AFFINITY 500 Turbo Power
Scheduled replacement – UV lamps, starters, filter panels
Maintenance
500 h
1000 h
3000 h
e)
3x
Ergoline ultra
520 W
12645-..
72, 75
f)
17 x
Ergoline VHP 12 Turbo Power
160 W
12557-..
62
g)
8x
Ergoline VHP 12 Turbo Power
160 W
12557-..
66
h)
18 x
Ergoline VHP 12 Turbo Power
160 W
12557-..
68
i)
7x
Ergoline VHP™ 251)
25 W
12562-..
64
f) g)
h)
43 x
S12
10002-..
62, 66, 68
i)
7x
S10
10047-..
64
e)
3x
1001069-..
72, 75
Note:
The UV high-pressure lamps used, Ergoline ultra, can be operated with different wattages.
1) = Shoulder tanner, optional
58
UV low-pressure lamps: Clean with plain water (damp cloth).
Filter panels: Clean with plain water (damp cloth).
AFFINITY 600 Turbo Power Air Condition
500 h
1000 h
3000 h
e)
3x
Ergoline ultra
520 W
12645-..
72, 75
f)
17 x
Ergoline VHP 12 Turbo Power
160 W
12557-..
62
g)
8x
Ergoline VHP 12 Turbo Power
160 W
12557-..
66
h)
21 x
Ergoline VHP 12 Turbo Power
160 W
12557-..
68
i)
7x
Ergoline VHP™ 251)
25 W
12562-..
64
f) g)
h)
46 x
S12
10002-..
62, 66, 68
i)
7x
S10
10047-..
64
e)
3x
1001069-..
72, 75
Note:
The UV high-pressure lamps used, Ergoline ultra, can be operated with different wattages.
1) = Shoulder tanner, optional
UV low-pressure lamps: Clean with plain water (damp cloth).
Filter panels: Clean with plain water (damp cloth).
59
Maintenance
Scheduled replacement – UV lamps, starters, filter panels
AFFINITY 800 Turbo Power Temptronic
Scheduled replacement – UV lamps, starters, filter panels
Maintenance
500 h
1000 h
3000 h
e)
4x
Ergoline ultra
520 W
12645-..
72, 75
f)
19 x
Ergoline VHP 12 Turbo Power
160 W
12557-..
62
g)
8x
Ergoline VHP 12 Turbo Power
160 W
12557-..
66
h)
24 x
Ergoline VHP 12 Turbo Power
160 W
12557-..
68
i)
7x
Ergoline VHP™ 251)
25 W
12562-..
64
f) g)
h)
51 x
S12
10002-..
62, 66, 68
i)
7x
S10
10047-..
64
e)
4x
1001068-..
72, 75
Note:
The UV high-pressure lamps used, Ergoline ultra, can be operated with different wattages.
1) = Shoulder tanner, optional
60
UV low-pressure lamps: Clean with plain water (damp cloth).
Filter panels: Clean with plain water (damp cloth).
Relamping / maintenance instructions
CAUTION – Damage due to improper maintenance!
Improper maintenance can cause the device to be damaged or to become unusable.
WARNING!
Danger: of burns from hot lamps and device parts!
If the tanning device was operated before being switched
off and opened, lamps and housing parts may be hot.
– Before replacing lamps or other spare parts, wait until
lamps and metal parts of the device have cooled down
sufficiently.
Danger of pinching!
When opening and closing the tray, panels and covers, you
can pinch your fingers.
Maintenance
It is imperative that you, the owner and/or operator, check all components for any signs of wear which may occur through normal use.
Observe the cleaning and maintenance schedule specified in the maintenance table on Page 55 to 60.
Only replace UV low-pressure lamps with the original lamp type or with
compatible lamps.
Only replace UV high-pressure lamps with the original lamp type or with
compatible lamps.
Should you require any assistance or need additional information, please
call Global Service USA at 800 445 0624, Monday through Friday 7:00
a.m. - 7:00 p.m. CT, Saturday 8:00 a.m. to 3:00 p.m.
– Always comply with the specified maintenance intervals.
– Follow the cleaning instructions.
– If the maintenance intervals for the UV lamps are exceeded or incompatible UV lamps are installed, the share of harmful UVB radiation
may increase. Sunburn and other skin damage may result.
61
Cleaning/replacing UV low-pressure lamps, sunbed base
AFFINITY 600/800
Maintenance
2
Power Off!
1
4
AFFINITY 500
AFFINITY 600/800
3
5
03519 / 0
62
03517 / 0
...
6
2
3
7
1
Maintenance
03099 / 0
03098 / 0
Close:
7
8
63
Maintenance
Cleaning/replacing UV low-pressure lamps in the optional shoulder tanner
2
4
3
5
Power Off!
1
03519 / 0
64
...
1
8
2
03099 / 0
03108 / 0
Maintenance
6
Close:
7
9
65
Cleaning/replacing UV low-pressure lamps, side section
Maintenance
2
4
Power Off!
1
3
1
2
03108 / 0
66
...
5
Maintenance
03099 / 0
Close:
6
67
Cleaning/replacing UV low-pressure lamps, canopy
Maintenance
Caution!
Canopy panel may break if allowed to fall or if pressure is exerted on the reverse side of an open
canopy. Such failure is not covered by manufacturer's warranty.
2
Power Off!
Danger of injury from the
canopy panel!
The canopy panel is heavy and
WARNING! falls down by itself after unscrewing the 3 screws.
1
3
1
2
– Support canopy panel.
– Loosen screws in the specified order.
03108 / 0
68
...
6
Maintenance
4
5
03099 / 0
69
Cleaning/replacing interior lighting
Maintenance
Caution!
Canopy panel may break if allowed to fall or if pressure is exerted on the reverse side of an open
canopy. Such failure is not covered by manufacturer's warranty.
2
Power Off!
Danger of injury from the
canopy panel!
The canopy panel is heavy and
WARNING! falls down by itself after unscrewing the 3 screws.
– Support canopy panel.
– Loosen screws in the specified order.
1
3
1
2
1
2
1
2
03347 / 0
70
...
4
6
2
03099 / 0
03299 / 0
Maintenance
1
Close:
5
7
71
Cleaning/replacing UV high-pressure lamps, side section
2
4
3
2
1
Maintenance
07226 / 0
Power Off!
1
3
5
07225 / 0
72
07227 / 0
...
DANGER! Fire hazard!
High pressure lamps that have
not been approved by Ergoline
DANGER! can explode. Hot lamp components can set other parts on fire.
People can be killed or severely
injured due to smoke and fume inhalation.
CAUTION!
Do not touch the glass bulbs of
the UV high-pressure lamps with
your bare fingers! Remove soiling
thoroughly.
– Only touch new UV high-pressure lamp on the gripping surface – see Figures 8 and 9.
– Only fit high pressure lamps
recommended by Ergoline.
– Clean the inside of the device
regularly. Fluff is inflammable!
07228 / 0
7
Maintenance
6
9
8
04044 / 1
07229 / 0
73
...
– Check safety switch.
10
Close:
12
14
2
Maintenance
13
03699 / 0
74
1
07231 / 0
07230 / 0
11
3
07232 / 0
Cleaning/replacing UV high-pressure lamps, canopy
Caution!
Canopy panel may break if allowed to fall or if pressure is exerted on the reverse side of an open
canopy. Such failure is not covered by manufacturer's warranty.
2
Danger of injury from the
canopy panel!
The canopy panel is heavy and
WARNING! falls down by itself after unscrewing the 3 screws.
1
Maintenance
Power Off!
3
– Support canopy panel.
– Loosen screws in the specified order.
07225 / 0
75
...
4
DANGER! Fire hazard!
High pressure lamps that have
not been approved by Ergoline
DANGER! can explode. Hot lamp components can set other parts on fire.
People can be killed or severely
injured due to smoke and fume inhalation.
6
3
2
1
– Only fit high pressure lamps
recommended by Ergoline.
Maintenance
5
7
07227 / 0
76
– Clean the inside of the device
regularly. Fluff is inflammable!
07228 / 0
07226 / 0
8
04044 / 1
...
– Check safety switch.
CAUTION!
Do not touch the glass bulbs of
the UV high-pressure lamps with
your bare fingers! Remove soiling
thoroughly.
10
12
2
– Only touch new UV high-pressure lamp on the gripping surface – see Figures 8 and 9.
9
1
07231 / 0
Maintenance
07230 / 0
3
11
07229 / 0
...
03699 / 0
77
13
Maintenance
07232 / 0
Close:
14
78
Cleaning/replacing accent light, canopy
Power Off!
1
3
1
2
Caution!
Paint damage possible!
When screwing, maintain a separation from the bottom edge.
2
Maintenance
03350 / 0
4
...
79
5
Maintenance
03099 / 0
6
80
Cleaning/replacing accent light, frontpanel
2
4
Maintenance
03099 / 0
Power Off!
1
3
81
Cleaning/replacing ambient lights (optional)
Maintenance
2
1
3
1
2
03350 / 0
82
03099 / 0
Cleaning filters, sunbed base
Hand-wipe lightly, dry or with water,
or use a vacuum cleaner.
2
4
Power Off!
1
3
Attention! The system can be
damaged by moisture!
When re-assembling, the cleaned
filters must be dry.
Maintenance
03319 / 0
...
83
Close:
Maintenance
5
6
84
7
Cleaning/replacing filter mats, canopy
Rinse with water or replace.
2
3
1
Maintenance
04047 / 0
Attention! The system can be
damaged by moisture!
When re-assembling, the cleaned
filter mats must be dry.
85
Maintenance
Cleaning/replacing filter mats, shoulder tanner
2
4
3
5
Power Off!
1
03519 / 0
86
...
Close:
Attention! The system can be
damaged by moisture!
When re-assembling, the cleaned
filters and filter mats must be dry.
9
Maintenance
6
Rinse with water or replace.
8
7
04047 / 0
87
AFFINITY 600/800
Air condition/Temptronic: Cleaning/replacing the filter mat, cleaning the cooling fins
Power Off!
Maintenance
1
2
Attention! Risk of damage to the
system!
Check the filter mat and the cooling
fins on the air conditioner regularly
and clean as necessary.
3
...
88
Clean carefully (vacuum
or wash) or replace.
6
8
03244 / 4
08101 / 1
Hand-wipe lightly, dry or with water,
or use a vacuum cleaner.
5
7
07464 / 0
Attention! The system can be
damaged by moisture!
When re-assembling, the cleaned
filters and filter mats must be dry.
Maintenance
4
Clean carefully.
...
03319 / 0
89
9
11
2
1
Maintenance
07465 / 0
Close:
10
12
04841 / 2
90
AFFINITY 800
Replacing AROMA container
2
4
BIS
AR RE
LTB EFO
HAST B
BE 007
02
/2
ON
ED
N
OPE
Maintenance
03354 / 1
Power Off!
1
3
5
2
1
BIS
AR RE
LTB EFO
HAST B
BE 007
02
/2
NE
N
DO
OPE
1
03246 / 0
3/2
08/0
06488 / 0
91
...
Close:
6
8
2
1
2
Maintenance
03355 / 0
7
92
AFFINITY 800
AQUA MIST SYSTEM: Replacing canister
2
3
5
3
AQUA M
IST
AQUA M
IST
4
6
Maintenance
04185 / 0
Power Off!
1
Health hazard!
Impurities in the AQUA MIST can
present a health hazard.
WARNING! – Use only original Sun Ergoline
AQUA MIST!
– Replace the entire canister.
– Do not top up or mix with tap
water or other liquids!
4
8
7
AQUA M
IST
– Do not swallow!
04186 / 0
93
...
5
7
Note:
For venting after canister replacement you must enter presetting
mode and choose function 18 (see
Page 100.
1
2
Maintenance
04101 / 1
Close:
6
8
04102 / 1
94
...
10
Maintenance
9
95
Changing presettings with the control panel
The setting mode enables you to call up operating states and make alterations to current settings.
Changing presettings
Changing to Presetting mode
– Press and hold the START/STOP button while simultaneously pressing the
button.
– Press the buttons
and
simultaneously for at least five
seconds outside a tanning process.
appears in the display.
– Enter the code (see Page 97).
Presettings
– Press the START/STOP button four times when you run the Presetting mode for the first time.
briefly appears in the display, then
(Function 1)
and the presetting value are displayed alternately (see column "On
delivery").
– By pressing the
-01- to -20-).
button you scroll up to the next function (from
– By pressing the
(from -20- to -01-).
button you scroll down to the next function
96
Increase the preset value:
Decrease the preset value:
– Press and hold the START/STOP button while simultaneously pressing the
button.
Reset to the last value set:
– Press the START/STOP button.
Reset to the delivered state:
– See function
Note:
.
The sunbed will automatically return to 'idle' mode 30 seconds
after the last button was pressed.
The presettings are listed beginning on Page 99.
Defining a code
– Select Function
.
– Press the START/STOP button for 3 seconds until
appears.
– Press the desired buttons consecutively:
– Press the buttons in the same sequence when
again.
–
appears
appears in the display. The set code has been saved.
– Please note the code for Customer Service.
Presettings
If you know the old code, you can define a new code at any time. We recommend that you already set a new access code during the initial startup.
97
Changing presettings with a hand-held unit
Some data can also be displayed and changed with a commercially available hand-held unit (e.g. from Palm). For this purpose you require special software (available in German and English). Please call 1-866-2439861 for more details.
Caution!
The code for access via the infrared interface is preset in the
software of the hand-held unit, and can therefore be used with
any unit. Anyone, who downloads the software from the Internet can access the unit date with a hand-held unit. Please note that Customer Service changes the preset access code during initial start-up – see software operating manual. Please
note the new code for future use!
Presettings
This code is independent of the access code for the presettings via the control panel.
Note:
Please read the operating manual for the Ergoline software
for instructions on how to display or change data with a handheld unit.
98
Information on operating the hand-held unit is contained in the manufacturer's documentation.
Description
on delivery
Total number of operating hours
Remaining operating time of UV low-pressure lamps (hours)
Remaining operating time of UV high-pressure lamps (hours)
Remaining operating time of shoulder tanner lamps (hours)
Remaining operating time of filter mats (hours)
Air conditioning operating hours
Decorative lighting operating hours (minutes)
When the maximum value is exceeded: Display
Presettings
No.
= continuous operation
Fan run-on time (minutes)
To set the time
To reset the device to ex-works setting (all functions)
99
No.
Description
To set the access authorisation code to enter setting mode (see page 97)
Adjust volume for voice output (Voice Guide)
Adjust volume for music output (Sound System)
Ambient temperature setpoint value (°C)
Recycle air during fan run-on time (+ = on / – = OFF)
Demand control unit (AQUA SYSTEM pump). Stated as percentages
Presettings
AQUA MIST running time (operating hours until canister replacement)/
Venting after canister replacement
Lower temperature limit of air conditioner
AQUA SYSTEM interval at start
-5: Shortest space between the sprays, 5: Longest space between the sprays
100
on delivery
Troubleshooting
In the case of a fault, a fault code appears on the display to simplify localizing of the fault cause:
• If a fault occurs, the fault code flashes in the display.
• If several faults occur, the fault messages are displayed alternately.
• The fault remedy is acknowledged by pressing the
button.
If the fault cannot be eliminated, inform Customer Service:
Troubleshooting
Global Service USA
A Div of JK Products & Services, Inc.
#1 Walter Kratz Drive
Jonesboro, AR 72401
800-445-0624
870-935-9046
e-mail: support@jkamerica.com
http://support.jkamerica.com
101
Error
Meaning
Fault in temperature sensor for UV low-pressure lamps
Temperature sensor for room
Panel switch for shoulder tanner
Air-vane switch does not switch on with fan running
Air-vane switch does not switch off 1 minute after fan switches off
Fault in front face tanner
Troubleshooting
Fault in center face tanner
Fault in rear face tanner
Fault in face tanner side section
Panel safety switch on decorative panel on canopy
102
Correction
Meaning
Correction
Emergency switch-off time exceeded
I²C bus fault
Switching error in series circuit of safety switch
Auxiliary controller
Heating controller
Face tanner controller
Speed control 1
Troubleshooting
Error
Speed control 2
Audio amplifier
Channel selection
103
Error
Meaning
Real-time clock
Parameter memory
Troubleshooting
Incorrect equipment of controller
104
Correction
Index
Index
B
Body ventilator, speed ................................ 37
C
Cabin lighting, cleaning/replacing ............... 82
Care ............................................................ 18
Changing presettings .................................. 96
Cleaning ...................................................... 19
Cleaning schedule....................................... 54
Cleaning/replacing accent light, frontpanel . 79
Code, defining, presettings ......................... 96
Conformity mark.......................................... 46
Contact lenses ............................................ 21
Container AROMA ...................................... 91
Cooling fins, air condition ............................ 88
D
Description of tanning device................ 24, 25
Disinfection.................................................. 19
Disposal of lamps........................................ 20
E
Ending tanning session............................... 28
Environmental protection ............................ 20
Equipment................................................... 17
Error codes................................................ 101
F
Facial tanners, regulating............................ 31
Fault codes................................................ 101
Filter mat, air condition................................ 88
Filter mats
Canopy ...............................................85
Shoulder tanner ..................................86
Filter panels, maintenance schedule...........58
Filters, sunbed base ....................................83
Frequency ...................................................46
Fusing..........................................................46
G
Glasses .......................................................21
Global Service USA, address........................3
Guidelines ...................................................16
H
Hand-held unit, changing presettings..........98
Head nozzles, speed...................................38
I
Info text........................................................43
Intended use................................................10
Interior lighting.............................................70
Interrupting tanning session ........................28
L
Lamps, disposal ..........................................20
Index
A
Accent lights
Cleaning/replacing ............................. 81
Maintenance schedule ....................... 57
Accessories .......................................... 17, 26
Acrylic glass, cleaning ................................ 19
Air condition
Filter mat ............................................ 88
Air condition, switching off .......................... 36
Allergies ...................................................... 21
Ambient lights, cleaning/replacing .............. 82
AQUA MIST
Body nozzle ....................................... 40
Head nozzle ....................................... 41
Replacing canister ............................. 93
AROMA
Replacing container ........................... 91
Switching on and off........................... 39
105
Index
M
Maintenance
Maintenance and care ....................... 18
Maintenance schedule ....................... 55
Overview AFFINITY 500 .................... 52
Overview AFFINITY 600 .................... 52
Overview AFFINITY 800 .................... 53
Safety information .............................. 61
Make-up...................................................... 21
Medication .................................................. 21
Music channel............................................. 44
Index
O
Operator commitments ............................... 10
Overview, operating elements .............. 24, 25
P
Packaging ................................................... 20
Plastic surfaces........................................... 19
Power consumption .................................... 46
Power, switching off.................................... 51
Preparation time ......................................... 27
Presettings.................................................. 96
Changing with a hand-held unit ......... 98
Changing with the control panel......... 96
Proper use .................................................. 10
Protective goggles ................................ 21, 27
106
R
Relamping ................................................... 61
RELAX, VITAL ............................................ 39
Running time of accent lighting ................... 30
S
Safety information, maintenance................. 61
Scheduled cleaning..................................... 54
Scheduled maintenance.............................. 55
Settings during start-up ......................... 28, 29
Showering ................................................... 21
Skin sensitivity............................................. 21
Skin types...................................................... 4
Spare parts.................................................. 18
Starters, maintenance schedule.................. 58
Starting tanning........................................... 27
Sunbed, how to use it.................................. 27
Surround cooling, adjust speed............. 37, 38
Switching shoulder tanner off and on.......... 33
T
Tanning ....................................................... 27
Tanning instructions .................................... 21
Technical data............................................. 46
Temptronic, adjust coolness ....................... 34
Timer ........................................................... 27
Troubleshooting ........................................ 101
U
Using the sunbed ........................................27
UV high-pressure lamps
Canopy ...............................................75
Side section ........................................72
UV lamps, maintenance schedule...............58
UV low-pressure lamps
Canopy ...............................................68
Side section ........................................66
Sunbed base ......................................62
UV low-pressure lamps, shoulder tanner ....64
V
VITAL, RELAX.............................................39
Voice Guide.................................................42
Voltage ........................................................46
Volume ........................................................45
Warranty
JK-Products, Inc. – Limited Warranty
This Limited Warranty applies only to the original purchaser of the equipment through JK-Products, Inc. or its authorized dealer or distributor, and
is not transferable.
Global Service USA obligations under this warranty are limited to repair
or replacement of any defective part without charge for that part to the
original purchaser, with the following exceptions:
A Fluorescent lamps are warranted against defects for a period of thirty
(30) days from date of sale.
B Only parts obtained through JK-Products, Inc., its authorized dealers
or distributors may be used. Transportation costs for parts shipped to
the consumer and the return of defective parts to Global Service USA
are not included.
C Labor will be furnished without charge for ninety (90) days from date
of purchase only. All labor and related charges must be authorized by
Global Service USA prior to start of repairs, and must coincide with
Global Service USA established rates and time allotment policy.
D Acrylic: Refer to Manufacturer's Acrylic Warranty Policy.
If the warranty card is not registered, proof of purchase from JK-Products, Inc. or its authorized dealer or distributor will be required prior to any
consideration on warranty claims. This could result in service delays.
This warranty is extended to the individual or legal entity, whose name
appears on the warranty registration card filed with Global Service USA,
or whose name appears on the original sale document and may not be
transferred to any other individual or legal entity.
This warranty does not apply to any failure of the product, or any parts of
the product due to alterations, modifications, misuse, abuse, accident,
improper maintenance, improper installation, acts of God or if the serial
number on the product has been removed, altered or defaced. Adequate
packaging must be used for returned goods to prevent freight damage.
There are no warranties which extend beyond the description on
the face hereof. There is no express or implied warranty of fitness
of merchantability.
The remedies provided in this limited warranty are the exclusive remedies provided to the purchaser by Global Service USA and are
provided in substitution of all other remedies. Consequential and
incidental damages are excluded.
No person, firm or corporation is authorized to obligate JK-Products, Inc.
for any liability in connection with the sale or use of these goods.
Limited warranty
JK-Products, Inc. warrants its products to be free from defects in materials and workmanship under intended normal use as described in the
unit's Operation and Instruction Manual, for a period of three (3) years
from date of sale.
It is imperative that the original customer completes and returns the enclosed warranty card within 10 days after purchase to insure valid registration and coverage for potential claims.
107
Warranty
Limited Acrylic Warranty
JK Products, Inc. warrants its acrylic sheets to be free from defects in material and workmanship, under intended normal use, for a period of one
(1) year from date of sale of the tanning bed. Due to the tanning lotions,
cosmetics, disinfectant and improper cleaners used on tanning surfaces
that cannot be controlled by JK Products, Inc., after the first thirty (30)
days of warranty period acrylic will be subject to a prorated cost to the
consumer.
JK Products, Inc. obligations do not include transportation charges on replacement acrylic.
JK Products, Inc. assumes no liability for the cost of removing defective
sheets or installing replacement sheets, nor for damage to persons or
property.
To make a claim, contact an authorized dealer or distributor of JK-Products, Inc. or Global Service USA with the model number, the serial number, and the date of purchase of the bed in which the acrylic will be used.
Limited warranty
There are no warranties which extend beyond the description on
the face hereof. There is no express or implied warranty of fitness
or merchantability.
The remedies provided in this limited warranty are the exclusive remedies provided to the purchaser by Global Service USA and are
provided in substitution of all other remedies. Consequential and
incidental damages are excluded.
108
Global Service USA
A Div of JK Products & Services, Inc.
#1 Walter Kratz Drive
Jonesboro, AR 72401
800-445-0624
870-935-9046
e-mail: support@jkamerica.com
http://support.jkamerica.com
Warranty
Policy & Procedures
1. When to file a Warranty Claim:
In the event that your tanning system is not functioning properly under intended normal use as described in the unit's Operation an Instruction
Manual, you may then have established cause to file a Warranty Claim.
NOTE:
Both the tanning system and legal registered owner must
meet the criteria established under JK Products, Inc. Limited Warranty as described in this manual before any Warranty Claim will be considered.
2. Where to call to place a Warranty Claim:
JK-Products, Inc. is supported nationwide by an extensive dealer/distributor network through whom the majority of our units are sold. These dealers/distributors are required by contract to stock sufficient parts to meet
the various warranty and nonwarranty needs of their customers.
Therefore, in order for you to properly file a Warranty Claim, you must locate the name and phone number of the dealer/distributor through whom
you purchased your unit. Normally this information can be easily located
either on your paid invoice or other proof of purchase documentation that
you received when taking delivery of the unit.
Next, notify the dealer/distributor of the serial number, model number and
date unit was purchased. This will initiate the Warranty Claim process.
Upon determination of the problem, your dealer/distributor can then supply you with the part(s) and proper instructions to return your unit to working order.
Each dealer/distributor has their own internal procedure for handling
Warranty Claims and credits.
NOTE:
JK-Products, Inc., the manufacturer, does not involve itself
in the direct handling of a Warranty Claim except where mitigating circumstances apply and where required by law.
NOTE:
If part returned to Global Service USA proves to be operational and not defective, or if product code numbers on part
do not correspond with individual unit date on file with Global Service USA, then a 30% restocking fee will be charged
in addition to the retail purchase price of part.
Acknowledgment of the Agreement is not required for acceptance of the
foregoing stipulations.
Labor Warranty Claim/Credit Procedures
Global Service USA furnishes labor without charge for a period of 90
days from date of purchase. All labor and related charges must be authorized by Global Service USA prior to start or repairs, and must coincide
with Global Service USA established rates and time allotment policy.
Please contact our Service Department for authorization and billing procedures.
109
Warranty Claims
Warranty Claims
Warranty
Limited Lifetime Warranty
Global Service USA warrants specific individual components of the tanning system against defects in materials and workmanship for the life of
the product. Coverage is limited to units purchased after November 1,
1994.
This warranty is restricted by the following components only:
• Steel Back Panels
• Structural Steel Frame Components
• Exterior Steel Body.
NOTE:
Components are warranted on an individual basis and not
as they may effect the complete product.
Warranty coverage does not include cosmetic abnormalities such as
scratches, nicks, dents, rust, oxidation of paint or other cosmetic changes that do not interfere with the designed function of the unit.
This warranty does not include failure of the product due to alteration,
modifications, misuse, abuse, improper maintenance, improper installation or repair.
Warranty Claims
This warranty is not transferable and is only applicable to the original purchaser named on a completed and registered warranty record at JKProducts, Inc. headquarters.
JK Products, Inc. obligations do not include transportation charged on
the shipping of new components to the customer or on the return of de-
110
fective components of the manufacturer. All freight charges must be paid
by the customer.
There are no warranties which extend beyond the description on the face
hereof. There is no express or implied warranty of fitness or merchantability.
The remedies provided in this limited warranty are the exclusive remedies provided to the purchaser by Global Service USA and are provided
in substitution of all other remedies. Consequential and incidental damages are excluded.
NOTE:
Any misuse, abuse, modification, alteration, improper maintenance, improper installation, etc. of this product or its intended use will subject said party to direct responsibility and
liabilities for any and all consequences resulting from such
action. Furthermore, such actions will void all warranties
and may relieve Global Service USA of any liabilities relating to said product.
Separate here
04.09.2006
14:32 Uhr
Seite 1
ERGOLINE AFFINITY
1000516
1001700.qxd
OPERATING INSTRUCTIONS
SUN ERGOLINE, A DIVISION OF JK-PRODUCTS & SERVICES, INC.
2905 Northwest Blvd., Suite 40 . Plymouth, MN 55441, USA
E-Mail: ergoline@sunergoline.com · Fax: 763.551.3607
Phone: 888.771.0996 · Website: www.sunergoline.com
Open as PDF
Similar pages