Owner`s Manual DS/DSV/RS S010-080 Series

Owner’s Manual
DS/DSV/RS S010-080 Series Dehumidifier
Controller Interface
Startup
When illuminated, indicates the displayed
variable is the indoor temperature.
Flashes to indicate there
is an active alarm.
Press SERVICE button
to view code.
When illuminated,
indicates dehumidification mode is ON.
When illuminated, indicates the displayed
variable is the indoor relative humidity.
When illuminated,
indicates auxiliary
heating is ON.
When illuminated,
indicates ventilation
mode is ON.
When illuminated, indicates the displayed
variable is the pool water inlet temperature.
When illuminated, indicates the displayed
variable is the spa water inlet temperature.
When illuminated,
indicates spa heating
mode is ON.
When illuminated,
indicates cooling
mode is ON.
When illuminated, indicates the displayed
variable is the outdoor temperature.
When illuminated,
indicates pool heating
mode is ON.
When illuminated,
indicates unit is ON.
When illuminated, indicates the
displayed variable is the air flow rate.
HT800 CONTROLLER
ENERGY RECYCLING DEHUMIDIFIER
DEHUMIDIFY
POOL HEAT
INDOOR
VENTILATION
SPA HEAT
HUMIDITY
COOL
AUX. HEAT
POOL
SYSTEM ON
SERVICE
SPA
SYSTEM
ON/OFF
SERVICE
OUTDOOR
%
Value of
selected
variable
AIR FLOW
C
F
DISPLAY
Press and hold for 5
seconds to toggle
between ON and OFF.
DRY-O-TRON® blower
may not stop in OFF.
See Options.
When illuminated,
indicates the
displayed variable
has the units %.
Press to display
alarm codes.
When illuminated,
indicates the
displayed variable
has the units °C.
Press repeatedly to
select different values to
be displayed.
Press to display set
points. Press again to
lower set points.
Press to display set
points. Press again to
raise set points.
When illuminated,
indicates the
displayed variable
has the units °F.
Data subject to change without notice.
Dectron, Inc.
May 2005
49
DS/DSV/RS 010-080 Series Dehumidifier
Owner’s Manual
Startup
Interface Map
HT800 C ON TR OLLER
ENERG Y RECYC LING D EHUMIDIFIER
SYSTEM
ON/OFF
DEHUMIDIFY
POOL HEAT
INDO OR
VEN TILATION
SPA H EAT
HUMIDITY
CO OL
AUX. H EAT
POOL
SYSTEM ON
SER VICE
SYSTEM
ON/OFF
SPA
SERVICE
OU TDOOR
%
AIR FLOW
C
F
DISPLAY
SYSTEM ON
INDOOR
Displayed variable is indoor temperature.
Displayed variable is indoor temperature set point.
Press
to increase the set point, or press
to decrease the set point.
In the event of a failure,
SERVICE
will flash. Press
SERVICE to view the alarm code.
DISPLAY
HUMIDITY
Displayed variable is indoor relative humidity.
Displayed variable is indoor relative humidity set point.
Press
to increase the set point, or press
to decrease the set point.
After the cause of the alarm
has been corrected, press and
hold SERVICE to clear the alarm
code.
DISPLAY
POOL
Displayed variable is pool inlet water temperature. This
will be skipped if programming does not allow for a pool.
Displayed variable is pool water temperature set point.
Press
to increase the set point, or press
to decrease the set point.
DISPLAY
SPA
Displayed variable is spa inlet water temperature. This
will be skipped if programming does not allow for a spa.
Displayed variable is spa water temperature set point.
Press
to increase the set point, or press
to decrease the set point.
DISPLAY
OUTDOOR
Displayed variable is outdoor air temperature. This will be
skipped if programming does not allow for an outdoor air
temperature sensor.
DISPLAY
AIRFLOW
Displayed variable is return air flow rate in % of maximum.
This will be skipped if programming does not allow for an
air flow sensor.
See calibration section for setup information.
DISPLAY
Data subject to change without notice.
50
Dectron, Inc. May 2005
Owner’s Manual
DS/DSV/RS S010-080 Series Dehumidifier
Change Temperature Display Mode
Startup
HT800 C ON TR OLLER
ENERG Y RECYC LING D EHUMIDIFIER
Your HT800 controller comes pre-programmed from the factory for the conditions determined at time of sale. If it is desired to change the temperature display mode, e.g. from °F to °C, follow the steps below. Choose one of the display codes according to the chart.
NOTE: “+” indicates pressing two buttons at the same time.
Press
1.
DISPLAY
DEHUMIDIFY
POOL HEAT
INDO OR
VEN TILATION
SPA H EAT
HUMIDITY
CO OL
A UX. HEAT
POOL
SYSTEM ON
SER VICE
SYSTEM
ON/OFF
SERVICE
SPA
OU TDOOR
%
AIR FLOW
C
F
DISPLAY
Screen
hold 3 seconds
+
x approx. 9 times
2.
3.
DISPLAY
existing
display code
4.
5.
OR
temperature
units
default
display
room temperature
measured by
Recommended-Factory default
°F
room
temperature return air sensor
Recommended
for a remote location
°F
room
temperature thermostat sensor
°F
set point
return air sensor
°F
set point
thermostat sensor
Recommended-Factory default
°C
room
temperature return air sensor
Recommended
for a remote location
°C
room
temperature thermostat sensor
°C
set point
return air sensor
°C
set point
thermostat sensor
The temperature display mode is now set. The display will return to normal approximately 35 seconds
after the last button is pressed.
Data subject to change without notice.
Dectron, Inc.
May 2005
51
DS/DSV/RS 010-080 Series Dehumidifier
Startup
Owner’s Manual
Set Pools
Set Pool Priority
Set Starting Delays
Your HT800 controller comes pre-programmed from the factory for the conditions determined at time of sale. If it is desired to change
a. the number of pools with water flow thorugh the DRY-O-TRON®, or
b. the heating priority of the pools, or
c. the starting delays, then
choose one of the display codes according to the chart below. For other conditions, consult Dectron or a Dectron-certified service technician.
HT800 C ON TR OLLER
ENERG Y RECYC LING D EHUMIDIFIER
DEHUMIDIFY
POOL HEAT
INDO OR
VEN TILATION
SPA H EAT
HUMIDITY
CO OL
AUX. H EAT
POOL
SYSTEM ON
SER VICE
SPA
SYSTEM
ON/OFF
SERVICE
OU TDOOR
%
AIR FLOW
C
F
DISPLAY
NOTE: “+” indicates pressing two buttons at the same time.
NOTE: Pool water should be connected to DRY-O-TRON DS/RS units in order
to re-cycle the lost pool heat. Lack of such connection and the necessary
adjustments below should be temporary.
Press
1.
DISPLAY
+
for 3 seconds
x approx. 9 times
2.
3.
DISPLAY
existing
display code
4.
5.
Screen
OR
If the relative humidity
is above 60% on compressor start, ignore
evaporator tempera- Pool water is Spa water is
ture sensor and force connected to connected to
the DRY-Opool heating mode for the DRY-O20 minutes.
TRON®.
TRON®.
Give the spa
heating
priority.
NO
NO
NO
NO
YES
NO
NO
NO
YES
NO
YES
YES
NO
YES
NO
YES
YES
YES
NO
NO
YES
YES
NO
YES
NO
YES
YES
YES
YES
NO
YES
YES
YES
YES
The controller will return to normal approximately 35 seconds
after the last button is pushed.
Data subject to change without notice.
52
Dectron, Inc. May 2005
Owner’s Manual
DS/DSV/RS S010-080 Series Dehumidifier
Set Auxiliary Pool Water Heater
Set Outdoor Temperature Sensor
Set Air Flow Sensor
Startup
Your HT800 controller comes pre-programmed from the factory for the conditions
determined at time of sale. If conditions have changed so that it is necessary to change
whether or not the unit will have an auxiliary pool water heater connected (see Installation
- Wiring - Control Signals), or whether or not the unit will have an outdoor air temperature sensor connected (see Installation - Wiring - Control Signals), or whether or not the
unit has an airflow sensor, follow these steps. Choose one of the
display codes according to the chart.
NOTE: “+” indicates pressing two buttons at the same time.
Press
1.
DISPLAY
+
3.
INDOOR
VENTILATION
S PA HEAT
HUMIDITY
COOL
AUX. HEAT
POOL
SYSTEM ON
SERV ICE
SYSTEM
ON/OFF
SERVICE
OUTDOOR
SPA
%
AI R FLOW
C
F
DISPLAY
for 3 seconds
DISPLAY
existing
display code
4.
5.
POOL HEAT
Screen
x approx. 9 times
2.
HT800 CONTROLLER
ENERGY RECYCLING DE HUMIDIFIER
DEHUMIDIFY
OR
latentsensible
heating
mode
latentsensible
auxiliary
heating
pool water
mode &
auxiliary auxiliary heater also A/C
pool water pool water works as option
heater 2nd stage installed
heater
outdoor
airflow
sensor temperature
option sensor option
installed
installed
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
YES
NO
NO
NO
NO
NO
YES
NO
NO
NO
NO
NO
NO
YES
YES
NO
NO
NO
NO
YES
NO
NO
NO
NO
NO
NO
YES
NO
YES
NO
NO
NO
NO
YES
YES
NO
NO
NO
NO
NO
YES
YES
YES
NO
NO
YES
NO
NO
NO
NO
NO
NO
YES
NO
NO
NO
YES
NO
NO
YES
NO
NO
YES
NO
NO
NO
YES
NO
NO
YES
YES
NO
NO
YES
NO
YES
NO
NO
NO
NO
YES
NO
YES
NO
YES
NO
NO
YES
NO
YES
YES
NO
NO
NO
YES
NO
YES
YES
YES
NO
NO
YES
YES
NO
NO
NO
NO
NO
YES
YES
NO
NO
YES
NO
NO
YES
YES
NO
YES
NO
NO
NO
YES
YES
NO
YES
YES
NO
NO
YES
YES
YES
NO
NO
NO
NO
YES
YES
YES
NO
YES
NO
NO
YES
YES
YES
YES
NO
NO
NO
YES
YES
YES
YES
YES
The display will return to normal approximately 35 seconds after the last button is pressed.
Data subject to change without notice.
Dectron, Inc.
May 2005
53
DS/DSV/RS 010-080 Series Dehumidifier
Owner’s Manual
Setup
This page is intentionally left blank.
Data subject to change without notice.
54
Dectron, Inc. May 2005
Owner’s Manual
DS/DSV/RS S010-080 Series Dehumidifier
Enable Operation
Startup
IMPORTANT!
This energy recycling dehumidification system has been completely tested under design conditions at the factory.
Start-up must be performed by a qualified factory trained service and installation technician.
Once start-up is completed, all portions of the “Start-up Report and Warranty Registration” form must
be completely filled in and a copy must be sent to the Dectron representative or to the Dectron factory in
order to register and validate the warranty.
Important!
Do NOT turn on the electric power unless the power supply voltage matches that specified on the unit
nameplate.
Be certain that there is no construction dust in the space or in the return duct.
1. Apply electric power
If the disconnect switch for the remote condenser is not already ON, turn it ON now.
This starts the compressor crankcase
heaters.
HT800 C ON TR OLLER
ENERG Y RECYC LING D EHUMIDIFIER
2. Start blower
On some units, the blower runs whenever electric power is applied to the unit.
On other units, it will be necessary to press
SYSTEM
ON/OFF
on the controller display until
DEHUMIDIFY
POOL HEAT
INDO OR
VEN TILATION
SPA H EAT
H UMIDITY
C OOL
A UX. HEAT
POOL
SYSTEM ON
SER VICE
SYSTEM
ON/OFF
SERVICE
SPA
OU TDOOR
%
AIR FLOW
C
F
DISPLAY
illuminates. The blower will start after a short delay.
If the blower does not turn the proper direction, a qualified person should disconnect electric power and interchange any two of the branch circuit wires at the DRY-O-TRON® input lugs. Do not
move any factory installed wires.
SYSTEM ON
3. Check Air Distribution
Be sure the air flow rate is correct before proceeding. Be sure that the air flow at each diffuser is correct. See
Installation - Air Distribution - Adjust Airflow.
STOP
This is necessary for the compressor crankcase heater function.
4. Enable compressor 1
For units with external overloads for the compressor, press START on the overload. For other units, turn ON the
compressor emergency switch.
Data subject to change without notice.
Dectron, Inc.
May 2005
55
DS/DSV/RS 010-080 Series Dehumidifier
Startup
Owner’s Manual
Read Primary Sensors
Indoor temperature is displayed by default. Other sensors may
be read by following the instructions below:
HT800 C ON TR OLLER
ENERG Y RECYC LING D EHUMIDIFIER
DEHUMIDIFY
POOL HEAT
INDO OR
VEN TILATION
SPA H EAT
HUMIDITY
CO OL
AUX. H EAT
POOL
SYSTEM ON
SER VICE
SPA
SYSTEM
ON/OFF
To read sensors other than INDOOR temperature, press
DISPLAY
SERVICE
OU TDOOR
%
AIR FLOW
C
F
DISPLAY
as necessary to cause the LED next to the
name of the desired quantity to illuminate. The numerical value in the screen is then the value of the indicated
sensor. The display will return to INDOOR if
DISPLAY
is pressed again after the last available sensor has been
shown. The display will return to INDOOR if no buttons are pushed for a preset time.
INDOOR
Displayed variable is present indoor temperature.
DISPLAY
HUMIDITY
Displayed variable is present indoor relative humidity.
DISPLAY
POOL
Displayed variable is present pool inlet water temperature.
This will be skipped if programming does not allow for a pool.
DISPLAY
SPA
Displayed variable is present spa inlet water temperature.
This will be skipped if programming does not allow for a spa.
DISPLAY
OUTDOOR
DISPLAY
AIRFLOW
Displayed variable is present outdoor air temperature. This
will be skipped if programming does not allow for an outdoor
air temperature sensor.
Displayed variable is return air flow rate in % of maximum.
This will be skipped if programming does not allow for an air
flow sensor.
DISPLAY
Data subject to change without notice.
56
Dectron, Inc. May 2005
Owner’s Manual
DS/DSV/RS S010-080 Series Dehumidifier
Read Secondary Sensors
Startup
HT800 C ON TR OLLER
ENERG Y RECYC LING D EHUMIDIFIER
DEHUMIDIFY
POOL HEAT
INDO OR
VEN TILATION
SPA H EAT
HUMIDITY
CO OL
A UX. HEAT
POOL
SYSTEM ON
SER VICE
SYSTEM
ON/OFF
To access the secondary sensors, press
SERVICE
and
DISPLAY
SERVICE
SPA
OU TDOOR
%
AIR FLOW
C
F
DISPLAY
at the same time, and hold them until
SERVICE
illuminates. Use the table below to interpret the display.
SERVICE
+
DISPLAY
SERVICE
INDOOR
Displayed variable is indoor temperature as measured at the return duct.
DISPLAY
HUMIDITY
Displayed variable is the temperature of the air leaving the evaporator.
DISPLAY
POOL
Displayed variable is pool outlet water temperature. This will be skipped if
programming does not allow for a pool.
DISPLAY
SPA
Displayed variable is spa outlet water temperature. This
will be skipped if programming does not allow for a spa.
DISPLAY
OUTDOOR
Displayed variable is supply air temperature.
DISPLAY
AIRFLOW
Future use
DISPLAY
If no buttons are pressed for a pre-set time, the display will automatically return to the primary sensors.
Data subject to change without notice.
Dectron, Inc.
May 2005
57
DS/DSV/RS 010-080 Series Dehumidifier
Startup
Owner’s Manual
View and Change Set Points
Some primary sensors have set points associated with them. To view and/or
change these set points, follow the chart below:
At any time, you may cease pressing buttons, and the display will return to
normal after a delay.
HT800 C ON TR OLLER
ENERG Y RECYC LING D EHUM IDIFIER
DEHUMIDIFY
POOL HEAT
INDO OR
VEN TILATION
SPA H EAT
H UMIDITY
C OOL
A UX. HEAT
POOL
SYSTEM ON
SER VICE
SYSTEM
ON/OFF
INDOOR
SPA
SERVICE
OU TDOOR
%
AIR FLOW
C
F
DISPLAY
Displayed variable is indoor temperature.
Displayed variable is indoor temperature set point.
Press
to increase the set point, or press
to decrease the set point.
DISPLAY
HUMIDITY
Displayed variable is indoor relative humidity.
Displayed variable is indoor relative humidity set point.
Press
to increase the set point, or press
to decrease the set point.
DISPLAY
POOL
Displayed variable is pool inlet water temperature. This
will be skipped if programming does not allow for a pool.
Displayed variable is pool water temperature set point.
Press
to increase the set point, or press
to decrease the set point.
DISPLAY
SPA
Displayed variable is spa inlet water temperature. This
will be skipped if programming does not allow for a spa.
Displayed variable is spa water temperature set point.
Press
to increase the set point, or press
to decrease the set point.
DISPLAY
OUTDOOR
Displayed variable is outdoor air temperature. This will be
skipped if programming does not allow for an outdoor air
temperature sensor.
DISPLAY
AIRFLOW
Displayed variable is return air flow rate in % of maximum.
This will be skipped if programming does not allow for an
air flow sensor.
See calibration section for setup information.
DISPLAY
Data subject to change without notice.
58
Dectron, Inc. May 2005
Open as PDF
Similar pages