Jeppesen FliteDeck Pro User Guide

Bring in an image from Corp Comm at 300 DPI and then shrinkwrap the
anchored frame (ESC + m + P).
Jeppesen FliteDeck Pro User Guide
Jeppesen
55 Inverness Drive East
Englewood, Colorado 80112-5498
This document supports version 2.1 of Jeppesen FliteDeck Pro.
Minimum operating system requirement for Jeppesen FliteDeck Pro 2.1 is iOS 6.0
and later.
Copyright © 2013 Jeppesen. All rights reserved.
September 2013
Revision 1.5
Copyright © 2013 Jeppesen. All rights reserved.
Except as otherwise provided and authorized in a written agreement between both Jeppesen and your company, Jeppesen's
copyrighted information and materials may not be processed, reformatted, reproduced, stored in a retrieval system, or
transmitted in whole or in part, in any form or by any means, whether electrical, mechanical, photocopying, recording or
otherwise, without prior written permission of Jeppesen.
iPad is either a registered trademarks or trademark of Apple in the United States and/or other countries.
Product or brand names may be trademarks or registered trademarks of their respective owners.
Contents
Jeppesen FliteDeck Pro User Guide
1
Jeppesen Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Working in Enroute View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Working in Terminal Charts View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
2
2
3
4
Viewing Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Chart Change Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing GPS Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performing Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Understanding Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
5
5
6
7
7
8
9
Enroute View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Creating a Route from the Route Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adding Alternate Airports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adding Route Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adding a SID and a STAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Editing Your Route from the Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adding and Removing Route Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Rubber-Band Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Viewing High and Low Enroute Themes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Viewing Enroute Map Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Contents
Viewing Map Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Searching in Enroute View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling the Moving Map and Displaying the Ownship . . . . . . . . . . . . . . . . . . . . .
Viewing North Up or Track Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Present Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Distance Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
16
17
17
17
18
Using the Offset Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Accessing Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Removing Current Flight Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Saving Flight Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Viewing Saved Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Saved Flight Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Saved Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sorting Saved Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting Saved Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
21
21
22
22
Alternate Access to Flight Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Loading a MyFlitePlan Online Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Terminal Charts View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing Terminal Charts for Your Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting Charts for Your Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigating Between Selected Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Charts for Airports in Your Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Charts for Airports Not In Your Route . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching to an Airport Diagram upon Landing . . . . . . . . . . . . . . . . . . . . . . . . . . .
Highlighting a Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rotating a Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Terminal Weather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JeppFD-Pro Global Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing JeppFD-Pro Global Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
24
25
26
26
27
27
28
28
29
29
29
Sleep Mode Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enroute View Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Charts View Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
METAR and TAF Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Account Info Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Support Information and Reset and Deactivate Settings . . . . . . . . . . . . . . . . . . . . . . . . .
30
30
30
31
31
32
Learn More . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
vi
Jeppesen FliteDeck Pro
User Guide
Jeppesen Support
United States Toll Free: 800-978-9186
United States: 303-328-6175
International: +49-6102-508290
Email: techsupport@jeppesen.com
Jeppesen Support
Working in Enroute View
The Views
Jeppesen FliteDeck Pro helps you increase your situational
awareness by viewing your flight with respect to both the
terminal and enroute air structures.
The two main views in Jeppesen FliteDeck Pro are the Enroute
view and the Terminal Charts view. You enter origin, destination,
and any alternate airports in the Enroute view, and then you
retrieve the terminal charts for those route airports in the
Terminal Charts view.
Working in Enroute View
To plan, create, and edit your route:
• Tap the Enroute view button.
From this view you can also view map details, search for map
information, view your aircraft position on the enroute map, view
distance calculations, load saved flights, and access notes and
chart change notices.
Working in Terminal Charts View
To access terminal charts for your route:
• Tap the Terminal Charts view button.
From this view, you can also track your aircraft position on georeferenced airport diagrams and approach procedures, highlight
and rotate your terminal chart, view chart change notices, print
terminal charts, and view terminal weather.
NOTE After you create a route in the Enroute view, the first
time that you tap the Terminal Charts view button, the taxi
diagram appears for the origin airport of your current flight.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
2
The Basics
Working in Terminal Charts View
The Basics
Pinch to Zoom - Zoom in and out of the display by moving your
thumb and finger in a pinching gesture.
Touch, Hold, then Release – When interacting with the enroute
map, you can touch, hold, and then release any object on the map
to add it to your route, delete it from your route, or view more
information about it.
Double-tap to Zoom Out - Double-tap one finger to zoom out to
the full extent of your route (in Enroute view) or to the full extent
of the chart (in Terminal Charts view).
Two-finger Swipe to Navigate - Swipe two fingers to flip
through your selected terminal charts, like flipping through pages
in a book.
Four-finger Swipe between Open Apps - Swipe four fingers to
move back and forth between one open app and another. For
example, you can do this gesture to navigate back and forth
between an open PDF reader and Jeppesen FliteDeck Pro.
Four- finger Swipe Up and Down – Swipe four fingers up and
down to show and hide the iPad taskbar. This gesture is helpful
when you want to go back and forth between iPad Settings and
Jeppesen FliteDeck Pro.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
3
The Basics
The Toolbar
The Toolbar
Viewing Manuals
You must have a PDF reader app installed on your iPad to view
your manuals.
To view manuals:
1. Tap the Manuals button.
2. Tap to select the manual that you want to view.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
4
The Basics
The Toolbar
3. Tap to select the PDF reader app of your choice.
You can use a four-finger swipe to move between the PDF
reader app and Jeppesen FliteDeck Pro.
NOTE If your company subscribes to Jeppesen Document
Management Services, you can also access company manuals
from within Jeppesen FliteDeck Pro by following the same
steps.
Viewing Chart Change Notices
Chart change notices highlight changes that affect Jeppesen
enroute or terminal charts that have not yet been published.
To view chart change notices:
1. Tap the Manuals button.
2. Tap the Notices button at the bottom of the Manuals
popover.
NOTE Chart change notices are displayed based on your
current view. In the Enroute view, notices for the coverage area
display. In the Terminal Charts view, notices for the selected
airport display.
Adjusting Brightness
To adjust the display brightness:
1. Tap the Brightness button.
2. Slide the brightness control to increase or decrease
brightness.
To adjust for optimal viewing in low-light conditions:
• Switch the Night Theme to ON.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
5
The Basics
The Toolbar
Viewing GPS Status Information
The GPS Status button appears on the toolbar when Enable
Moving Map or either one of the two Display Ownship settings
in the JeppFD-Pro global settings are ON.
Tap the GPS Status button to view:
• Ground Speed.
• GPS Altitude.
• Coordinates for the Last Position Received, including date
and time received.
• GPS Accuracy information.
NOTE The GPS Status button appears on the toolbar when
Enable Moving Map or any one of the Display Ownship
settings in the JeppFD-Pro global settings are ON.
A badge appears over the GPS Status button if the GPS signal
does not meet the minimum accuracy requirements for the
current view.
The minimum accuracy requirement to display the ownship on
an enroute map is 200 meters, and on an airport diagram it is
17 meters.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
6
The Basics
The Toolbar
Accessing Settings
From the Settings popover, you can:
• Perform updates. See see “Performing Updates” on page 7
for more information.
• View help.
• Print the displayed terminal chart.
• Show or hide the terrain legend on the enroute map. (The
terrain legend is displayed only if the terrain filter button is
toggled ON to show terrain in the Enroute view).
• Enable or disable the automatic display of the taxi diagram
on landing. See “Switching to an Airport Diagram upon
Landing” on page 27 for more information.
Performing Updates
Whenever data updates are available, a badge appears on the
Settings button.
To perform updates:
1. Tap the Settings button.
2. Tap the Updates button to view available updates.
3. Tap the Update button.
4. Tap the Done button when the update is complete.
NOTE The download time depends on your connection to the
Internet and the size of the required updates. At anytime during
the update, you can tap the Cancel button to cancel the
download and continue to use the data that was already
installed.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
7
The Basics
The Toolbar
Understanding Updates
The data delivery system for Jeppesen FliteDeck Pro can track,
audit, and report on updates to devices globally.
When more than one version of Jeppesen terminal chart or
enroute data is available, the current version is displayed and an
amber tag indicates multiple versions.
Mid-Cycle Terminal Chart Updates
Jeppesen FliteDeck Pro updates terminal charts according to your
company’s subscription. When a terminal chart is revised midcycle, the revision date appears along with the amber tag next to
the chart title on the chart list.
To change terminal chart versions when more than one version of
the chart is available:
1. Tap the amber tag from the chart list to display the revision
popover.
2. Tap the chart title to view a different version of the chart.
Enroute Database Effectivity
Jeppesen FliteDeck Pro updates the enroute database every 28
days. Jeppesen FliteDeck Pro automatically switches to the
current database when it takes effect. Since you can also
download enroute data up to seven days before the effective date,
two versions of the enroute database can be loaded on your iPad
at the same time. When two enroute databases are available, the
effective date of the database in use appears in the amber tag on
the map. You can manually switch back to the expired database,
or ahead to the future effective database to support situations like
flying across international datelines.
To manually change enroute database versions:
1. Tap the Settings button.
2. Tap the Updates button.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
8
The Basics
The Toolbar
3. Tap the Enroute Issue Date fly-out.
4. Tap to select the database that you want to view.
5. Tap the Updates button.
6. Tap Done.
Locking the Display
The display lock feature prevents you from accidentally panning
or zooming away from your current display.
To lock or unlock your display:
• Tap the Display Lock button.
When the display is locked, the Display Lock button is red and
you cannot access any other buttons, or pan or zoom. You can
still perform a four-finger swipe to move between open
applications.
NOTE When the display is locked, the enroute map will still
move (when Enable Moving Map is ON in the JeppFD-Pro
global settings) and the automatic switch to the airport diagram
will occur (when it is set to ON from the Settings popover).
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
9
Enroute View
Creating a Route from the Route Drawer
Enroute View
Creating a Route from the Route Drawer
You can plan, create and edit your route from the Route Drawer,
including adding multiple alternate airports, route points, and
SIDs and STARs.
To create a route using the Route Drawer:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap in the Origin field. and enter the four-letter airport
ICAO identifier or city name for the origin airport.
3. Tap the in Destination field and enter the four-letter airport
ICAO identifier or city name for the destination airport.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
10
Enroute View
Creating a Route from the Route Drawer
4. Tap Done on the keyboard.
NOTE If you enter an invalid airport ICAO identifier, a
message appears at the bottom of the route box stating that the
airport is invalid and was not found.
To search for an origin or destination airport:
1. In the origin or the destination airport field, enter two or
three characters of the airport ICAO identifier or the city
name.
2. Tap Search on the keyboard.
3. Tap the desired airport from the search results.
Adding Alternate Airports
Jeppesen FliteDeck Pro supports your need to add multiple
alternate airports. After you add them, the alternate airports are
highlighted on the map.
To add alternate airports to your route:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap in the Alternate Airports field.
3. Enter the four-letter airport ICAO identifier or city name.
4. Tap the space bar on the keyboard to validate the airport
and add additional alternate airports.
If the entry is not valid, a message displays at the bottom of
the route box.
If there is more than one option available, a list displays
multiple airports from which you can choose.
5. Tap Done on the keyboard when you finish adding alternate
airports.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
11
Enroute View
Creating a Route from the Route Drawer
Adding Route Points
To add route points (Navaids, waypoints, airports, and/or
airways) from the Route Drawer:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap in the route box.
3. Using the keyboard, or by copying and pasting, enter the
route points into the route box.
4. Tap Done on the keyboard when you finish.
When entering route points from the Route Drawer, both plain
language and dot-notation formats are supported. For example:
• N37 56.6 W122 21.4 SAC V23 RBL (plain language)
• N37.56.6.W122.21.4.SAC.V23.RBL (dot-notation)
When using dot-notation, use:
• Two dots to indicate direct-to points. For example:
FXV..FWA..CR
• One dot between via routings (points that begin and end
airway segments). For example:
LULOX.UN12.IDOKI.UM25.INGOR.UM25.DVL
In addition, the following latitude and longitude coordinates are
supported in the route box:
• Nxx Wxxx (N 37 W122)
• Nxx.x Wxxx.x (N37.5 W122.2)
• Nxx xx.x Wxxx xx.x (N37 56.6 W122 21.4)
• Nxx xx.xx Wxxx xx.xx (N37 56.60 W122 21.40)
• Nxxxx.xWxxxxx.x (N3756.6W12221.4)
• NxxxWxxxx (N375W12221)
• N xx.xxxxx W xxx.xxxxx (N 37.56600 W 122.21400)
• N xx xx W xxx xx (N 37 56 W 122 21)
• N xx xx xx W xxx xx xx (N 37 56 60 W 122 21 40)
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
12
Enroute View
Creating a Route from the Route Drawer
Adding a SID and a STAR
Before you can enter a SID or a STAR, you must first enter the
corresponding origin or destination airport.
To enter a SID or a STAR:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap in the route box.
3. Using the keyboard, or by copying and pasting, enter the
SID or STAR (or both) into the route box in the appropriate
format.
• For SIDs the format is: SID.Transition
For example: REBAS5.REBAS
• For STARs the format is: Transition.STAR
For example: OLM.OLM7
NOTE Only transitional points of a SID or STAR are depicted
on the enroute map.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
13
Enroute View
Creating a Route from the Route Drawer
Editing Your Route from the Map
You can plan, create, and edit your route directly from the map.
Some ways that you can edit your route from the map include
adding and removing route points and rubber-band routing.
Adding and Removing Route Points
To add or remove route points from your route by interacting
with the map:
1. Touch, hold, and then release the desired route point on the
map.
2. Tap the Add To Route, Direct To (if available), or
Remove From Route button.
NOTE Tapping the unfilled star next to a user-created
waypoint fills the star and ensures that the waypoint persists on
the map after the route has been cleared. You can clear the
user-created waypoint by tapping the star again.
Rubber-Band Routing
To edit your route with rubber-band routing:
1. Touch and hold a point along your existing route line.
2. Drag the route line to the desired location and release.
3. Tap the Add To Route button or, if it is available, the
Direct To button.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
14
Enroute View
Viewing Enroute Map Features
Viewing High and Low Enroute Themes
The same high and low themes as depicted on precomposed paper
enroute charts are available for the enroute map.
To change enroute map themes:
1. Tap the Enroute Theme button.
2. Tap the desired theme.
Viewing Enroute Map Features
Depending on the zoom level, certain enroute map features are
automatically filtered to declutter the map. When a feature is
available for display, you can manually show or hide it by
tapping on its corresponding filter button.
To show or hide an enroute map feature:
• Tap the filter button that corresponds to the specific enroute
map feature.
The map features that you can show or hide are:
• Airports
• Airways
• Waypoints
• Navaids
• Airspace
• Terrain
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
15
Enroute View
Searching in Enroute View
Viewing Map Details
To view map details:
• Touch, hold, and then release an object on the map.
The selected object is highlighted and a popover displays
the object detail.
Depending on the type of object that you select, you might have
the option to review additional information about the object. For
example, when you view the details of an airport on the map, a
popover displays airport information including:
• Runways information.
• Communication information.
• METAR and TAF weather information, if available.
• The Go To Airport Diagram button, which switches to the
selected airport’s airport diagram.
Searching in Enroute View
To search for map information:
1. Tap the Search button.
2. Enter two or more characters in the search field.
3. Tap the Search key on the keyboard.
4. Tap to select the object and view it on the map.
NOTE Search results are ordered from nearest to farthest,
either from the chart center or your aircraft location. Distance is
indicated in nautical miles.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
16
Enroute View
Enabling the Moving Map and Displaying the Ownship
Enabling the Moving Map and Displaying the Ownship
The ownship appears on the enroute map when Enable Moving
Map and Display Ownship on Enroute in the JeppFD-Pro
global settings are ON. These settings are OFF by default. The
minimum required GPS accuracy to display the ownship on an
enroute map is 200 meters.
NOTE Operators may require additional authorizations to use
this functionality in flight. Refer to your operational procedures
for more information.
Viewing North Up or Track Up
To change the enroute map orientation:
• Tap the Compass Rose button.
NOTE To view the enroute map in Track Up orientation,
Enable Moving Map in the JeppFD-Pro global settings must be
ON.
Viewing Present Position
To recenter the map over your aircraft position after you have
panned away:
• Tap the Present Position button.
NOTE To recenter the map over your aircraft position, Enable
Moving Map in the JeppFD-Pro global settings must be ON.
Operators may require additional authorizations to use this
functionality in flight. Refer to your operational procedures for
more information.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
17
Enroute View
Viewing Present Position
Viewing Distance Calculations
The distance measuring tool is a set of rings or arcs that provide
constant awareness of your distance to features on the map at a
glance. As you zoom in or out of the map, the range rings change
with the map scale.
To show and hide the distance measuring tool:
• Tap the Range Rings button.
The center-most ring includes a compass rose that indicates true
north, south, east, and west. The center is called the reference
point. Tic marks are drawn at intervals in between the cardinal
points of the compass.
Depending on the map orientation, the range rings are centered at
a different location within the view.
• In North Up orientation, the range rings are centered on a
point in the middle of the map window.
• In Track Up orientation, the arcs are centered on a point that
bisects the mid-point of the horizontal axis, and placed 25%
from the bottom edge of the map on the vertical axis. In
Track Up orientation, the compass rose rotates as your
aircraft changes direction.
Using the Offset Indicator
To determine the distance and direction from your aircraft to any
other object on the map:
1. Tap the Range Rings button to show the range rings.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
18
Enroute View
Accessing Notes
2. Pan the map so that the map object in question is in the
center of the inner range ring.
A magenta offset indicator appears which shows the
distance and direction to your aircraft position.
NOTE To use the offset indicator, you must have both Enable
Moving Map and Display Ownship on Enroute ON in the
JeppFD-Pro global settings. Also, if you toggle range rings off,
the offset indicator is no longer displayed.
Accessing Notes
All of the notes provided on precomposed paper charts are
available:
• Operational: Tactically important information regarding
specific navigation elements. These notes are equivalent to
Ball Flag notes on paper charts and are indicated visually on
the enroute map by blue “i” icons.
• Regional: Procedures, conditions, or requirements for a
specific geographical region. These notes are equivalent to
Floating notes on paper charts.
• Reference: Aeronautical reference information for large
charted areas. These notes are equivalent to End Panel notes
on paper charts.
Notes are based on your current view, and you must be zoomed in
to a level of 100 NM or less to access them.
To access notes along your route:
1. Tap the Notes button.
2. Tap the button that corresponds to the type of note that you
want to view.
3. Tap the desired note.
The object on the map to which the note applies is highlighted.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
19
Enroute View
Removing Current Flight Information
Removing Current Flight Information
To clear the current route, airports, and any associated terminal
chart selections:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap the New Flight button.
3. Tap OK to confirm.
Saving Flight Information
Any route can be saved as long as it has at least one airport
(origin, destination, or alternate). Saved flights include the route
definition and any terminal charts you have selected for the flight.
The flight is named using the origin and destination airports, and
there is no limitation to how many routes you can save.
To save your flight:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap the Save button in the Route Drawer.
If a route with the same origin and destination airport
exists, you are given two options to Save (to overwrite the
existing route), or Save as New (to create a new route).
Viewing Saved Flights
To view your saved flights:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap the Flights button.
You can view saved flights in List view (default) or Card view.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
20
Enroute View
Saving Flight Information
Flight information for both views includes the:
• Flight name (identified by origin and destination airports).
• Date that the flight was last updated.
• Route definition.
• Alternate airports, if any.
In addition, in Card view, the selected terminal charts for the
saved flight are listed.
Switching Saved Flight Views
To switch the saved flights view:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap the Flights button.
3. Tap either the List or Card view button.
Loading Saved Flights
To load a saved flight:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap the Flights button.
3. Tap the Load button next to the flight that you want to load.
NOTE If you already have a flight displayed and you load
another flight, you will be given the option to either Save Before
Loading (so you won’t lose your current flight information),
Load Without Saving (which removes your current flight
information) or Cancel (which cancels the Load).
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
21
Enroute View
Alternate Access to Flight Information
Sorting Saved Flights
To sort your saved flights:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap the Flights button.
3. Tap the Sort By down arrow.
4. Tap to select either Flight By Name or Date Updated.
Deleting Saved Flights
To delete a saved flight:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap the Flights button.
3. Tap the Edit button.
4. Tap the flight that you want to delete.
5. Tap the Delete button.
6. Tap Delete Flight(s).
7. Tap the Done button.
8. Tap the Done button to return to the Enroute view.
Alternate Access to Flight Information
Your configuration of Jeppesen FliteDeck Pro affects what you
can do and what you see in the Route Drawer. With certain
configurations you can import saved flights from Jeppesen
MyFlitePlan Online.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
22
Enroute View
Alternate Access to Flight Information
Loading a MyFlitePlan Online Route
With an Internet connection and your MyFlitePlan Online user
name and password entered in the JeppFD-Pro global settings,
you can load routes from your Jeppesen MyFlitePlan Online
account.
To load a MyFlitePlan Online route:
1. Tap the route drawer bar to open the Route Drawer.
2. Tap the Flights button.
3. Tap the FPO button at the top of the Saved Flights popover.
4. Tap the Load button next to the route that you want to load.
NOTE The FPO button appears only if you have entered
account information under Services in the JeppFD-Pro global
settings.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
23
Terminal Charts View
Accessing Terminal Charts for Your Route
Terminal Charts View
Accessing Terminal Charts for Your Route
Terminal charts are organized by chart type categories. You can
tap a chart type button to display charts in a category.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
24
Terminal Charts View
Selecting Charts for Your Flight
The chart type buttons include:
• REF (Reference)—Nonprocedural charts, sorted
alphabetically by title.
• CO (Company): If you subscribe to Jeppesen Tailored
Charting Services, you will see a Company category, which
includes your company’s tailored charts.
• STAR (Standard Terminal Arrival)—Arrival charts, sorted
alphabetically by title.
• APP (Approach)—Approach procedures, grouped by
runway and sorted by index number.
• TAXI (Taxi)—Taxi charts, sorted by index number.
• SID (Standard Instrument Departure)—Departure
procedures, sorted alphabetically by title.
Selecting Charts for Your Flight
You can select multiple charts for easy access during critical
phases of flight.
After you have selected a chart, whenever you tap that chart type
button, the last viewed, selected chart from that category
displays. If no charts are selected in a chart type, the chart list
opens.
To begin selecting charts:
1. Tap the chart type button for the type of chart that you want
to view. You can tap the chart title to preview the chart
before selecting it.
2. Tap the chart selector button to place a check next to the
chart to select it and add it to the selected charts bar.
3. Tap the chart to close the chart list or tap another chart title
to preview another chart from that category.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
25
Terminal Charts View
Viewing Charts for Airports in Your Route
Navigating Between Selected Charts
Each selected chart is represented by a pagination dot on the
selected charts bar at the bottom of the chart display window.
Chart category labels also appear above the dots.
The highlighted dot indicates the chart that is currently displayed
in the series of selected charts.
You can navigate between selected charts a number of different
ways. You can:
• Use a two-finger swipe in the direction of the charts you
want to view.
• Tap the chart type button to jump across multiple selected
charts.
• Tap outside on the left or right side the selected charts bar to
move to the previous or next chart.
Viewing Charts for Airports in Your Route
After you create a route in the Enroute view, the first time that
you tap the Terminal Charts view button, the airport diagram
appears for the origin airport. To view other chart types for the
origin airport, tap a chart type button for the category of charts
that you want to view.
To view terminal charts for another airport that is in your route
(including any alternate airports that you entered):
1. Tap the Airport button.
2. Tap to select the desired airport from the list of airports in
your route.
Jeppesen FliteDeck Pro auto-selects the airport diagram for
that airport.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
26
Terminal Charts View
Viewing Charts for Airports Not In Your Route
Viewing Charts for Airports Not In Your Route
To access terminal charts for an airport that is not in your current
route:
1. Tap the Airport button.
2. Tap the All Airports button at the bottom of the Airports
popover.
3. Tap in the Search field to access the keyboard, and then
enter the ICAO identifier or the city name.
4. Tap to select the desired airport from the list of airports.
Jeppesen FliteDeck Pro auto-selects the airport diagram for
that airport.
Switching to an Airport Diagram upon Landing
The automatic switch to an airport diagram upon landing is OFF
by default in Jeppesen FliteDeck Pro. The switch to an airport
diagram upon landing is based on the speed threshold that you
specify in the Arpt Diagram (10-9) Speed Threshold JeppFDPro global setting. The default speed threshold is 40 knots.
To enable the automatic display of an airport diagram upon
landing:
1. Tap the Settings button.
2. Switch Show Taxi On Landing to ON.
NOTE Operators may require additional authorizations to use
this functionality. Refer to your operational procedures for more
information.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
27
Terminal Charts View
Highlighting a Chart
Highlighting a Chart
You can highlight your terminal charts to highlight specific
information.
To highlight information on a terminal chart:
• Tap the Highlight button.
In highlight mode, your finger acts as a highlighter on the
chart.
Highlights persist on the chart until you remove them or the
chart is updated.
To remove the last highlight or mark:
• Tap the Undo button.
To clear all highlights on the displayed terminal chart:
• Tap the Clear All button.
To exit the highlight mode:
• Tap the Highlight button again.
Rotating a Chart
There are instances when the optimal view for your terminal chart
is when it is rotated.
To rotate your terminal chart clockwise 90 degrees:
• Tap the Rotate button.
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
28
JeppFD-Pro Global Settings
Viewing Terminal Weather
Viewing Terminal Weather
To view text weather from the Terminal Charts view:
• Tap the Weather button.
• Tap Raw or Decoded.
METAR and TAF updates occur separately.
If the weather data is expired, a warning appears in red in the
same location as the weather age. The warning indicates how
long ago the weather data expired.
JeppFD-Pro Global Settings
Accessing JeppFD-Pro Global Settings
To adjust the JeppFD-Pro global settings:
• Tap Settings on your iPad Home screen.
• Tap JeppFD-Pro.
NOTE Global settings can be defined by each operator.
Displaying ownship or aircraft position may not be approved for
use in your operation. See your company policies for specific
settings.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
29
JeppFD-Pro Global Settings
Accessing JeppFD-Pro Global Settings
Sleep Mode Setting
To set Sleep Mode:
• Sleep Mode is ON by default. Switch Sleep Mode to OFF
to ensure that the iPad stays powered on during flight.
(Setting Sleep Mode to OFF reduces battery life.)
Enroute View Settings
The default settings for Enroute View are:
• Enable Moving Map is OFF by default. Switch it ON to
track your aircraft, display the ownship, view the map in a
Track Up orientation, or recenter the enroute map over your
aircraft location after panning away.
• Display Ownship on Enroute is OFF by default. Switch it
ON to display ownship position over the enroute map. The
minimum GPS accuracy requirement to display ownship on
the enroute map is 200 meters.
NOTE Enabling the moving map without displaying ownship
allows you to have a Track Up orientation without the ownship
showing on the map.
Terminal Charts View Settings
The default settings for Terminal Charts View are:
• Display Ownship on Airport Diagram is OFF by default.
Switch it ON to display ownship position over the airport
diagram. The minimum GPS accuracy requirement to
display ownship on the airport diagram is 17 meters.
• Default Chart Zoom Level is Fit Full Chart by default.
This scales the chart to fit the iPad display screen. No
horizontal or vertical panning is needed to view the entire
chart. Fit to Width scales the width of the chart to match
the width of the iPad display screen. No horizontal panning
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
30
JeppFD-Pro Global Settings
Accessing JeppFD-Pro Global Settings
is needed to view the entire width of the chart but if the
chart is longer than the display, you can pan up and down to
view the whole length of the chart.
• Arprt Diagram (10-9) Speed Threshold is 40 knots by
default. This is the speed threshold at which the automatic
display of a taxi diagram occurs. You can optimize the
settings for your aircraft by adjusting the threshold speed.
Values range from 30 to 80 knots.
METAR and TAF Settings
Change the METAR and TAF settings to reflect your preferences
for viewing terminal weather.
• The Temperature Unit are Fahrenheit (default) or Celsius.
• The Default Format options are Raw (default) or Decoded.
Account Info Settings
Account Info includes the Version and Registration number for
the Jeppesen FliteDeck Pro application in use, and a Services flyout.
• Version displays the application ID and the build number.
• Registration displays the recipient name.
• Services includes an option for entering your MyFlitePlan
Online and Company Manuals account information.
FlitePlan Online Account Information is used so that you
can load MyFlitePlan Online routes. The Company
Manuals Account Information is used to so that you can
view your company manuals from the Manuals button on
the toolbar.
September 2013
Jeppesen FliteDeck Pro User Guide
Copyright © 2013 Jeppesen. All rights reserved.
31
Learn More
Accessing JeppFD-Pro Global Settings
Support Information and Reset and
Deactivate Settings
The Jeppesen Support fly-out displays contact information for
the Jeppesen support team.
The Terms & Conditions fly-out displays links to both the
current application and data Terms and Conditions.
To restore all application settings to their default values, switch
Reset User Settings to ON.
To remove all Jeppesen data and clear the activation information
(including the site key), switch Deactivate to ON, and then
relaunch the application.
Learn More
To learn more about Jeppesen FliteDeck Pro, please visit our
website for video tutorials, FAQs, and e-learning. Jeppesen also
provides the following resources:
• Frequently Asked Questions
• Jeppesen Mobile Apps & iPad Mini
• Jeppesen FliteDeck Pro iOS Features
• Authorization Support
Jeppesen FliteDeck Pro User Guide
September 2013
Copyright © 2013 Jeppesen. All rights reserved.
32
Open as PDF
Similar pages