CODES - THE BASICS
• The KitLock has four code levels
available:
i) Master Code
ii) Sub-Master Code
iii) User Code
iv) Technician Code
• The KitLock is supplied with two
factory set codes:
Master Code: 11 33 55 77
User Code: 22 44
• When fitted immediately change
the Master Code and User Code.
• All Master Codes and Sub-Master
Codes are 8 digits long.
• All User Codes are 4 digits long.
• All Technician Codes are
6 digits long.
• The lock ‘open’ time is set
at 4 seconds.
OPERATING INSTRUCTIONS
FUNCTIONS
Before programming select the most
appropriate function for the application.
A)PRIVATE USE
Important Note: This is the default
function and is already
pre-programmed in new locks.
This is the most common function
and is used where the same code
will be repeatedly used.
B) PUBLIC USE
The user enters their own personal
four-digit code. This locks the lock.
The same code is entered to open the
lock before being erased and ready
for the next new user.
This function is used for short term,
multi occupancy applications,
e.g. a locker in a leisure centre.
The KitLock 1200 has a 10 button
keypad and a # bar.
The # bar is only used for programming
functions when lock is in A) Private Use
Function.
Blue LED = Code accepted
Red LED = Code rejected
CODES The lock has the following code levels:
A) MASTER CODE
The Master Code can:
• Open the lock
• Change the Master Code
• Set the Sub-Master and User Code
• Change the Sub-Master and User Code
• Delete the Sub-Master and User Code
• Select between Private and Public
Functions
• Set or delete Technician Code
• Disable or enable the sounder
B) SUB-MASTER CODE
The Sub-Master Code can:
• Open the lock
• Change the Sub-Master
• Set / Change / Delete / the User Code
C) USER CODE
The User Code can:
• Open the lock
• Change the User Code
D) TECHNICIAN CODE
The Technician Code can:
• Open the lock in Technician mode
without erasing User Code when in
B) Public Use Function.
The same code cannot be programmed
into more than one level.
LOST CODE PROCEDURE
Note: The procedure requires the door to
be open.
• Remove the rear fixing bolts and
remove the lock from the door.
• Remove one battery.
• Press and hold the 1 button, replace
the battery, the Blue LED will flash
twice, release the 1 button. Within
three seconds press the 1 button
three times.
T he Blue LED will flash twice and the
lock will have reverted to the factory
Master Code 11 33 55 77 and all other
stored settings will be erased.
PENALTY TIME
• Entering three incorrect codes will
cause the lock to shutdown for 10
seconds.
BATTERY POWER
• The KitLock should provide well
in excess of 50,000 openings, of 4
seconds each, from 2 x AAA 1.5v cells.
LOW BATTERY
• When the battery power is low the Red LED will flash three times
before the
Blue LED lights accepting
the code. Fit new batteries as soon as
this happens. The lock will operate for
100 times with low battery.
•
•
Code rejected
• low
battery indication
• Code accepted
BATTERY FAILURE OVERRIDE
The KitLock has been designed so an
external PP3 battery can be placed against
the external contacts beneath the handle
so that the lock can be opened to replace
batteries should they fail.
THE PROCEDURE IS AS FOLLOWS:
• Place the contact points of the PP3
battery against the contact points
at the base of the lock, making firm
maintained contact.
• The positive + PP3 terminal against the
+ contact on the lock, and the negative
– PP3 terminal against the negative
contact on the lock. See image.
• Enter the Master Code.
• The lock will now withdraw the locking
pin allowing the lock to open.
• Fit new batteries by removing the lock
from the door. Refit the lock.
Every program command must commence
by pressing the # bar when in A) Private
Use Function (factory default), followed by
either the Master Code, Sub-Master Code
or User Code.
• When in B) Public Use Function the # bar is not required for
programming. Ensure lock is
free of User Code.
• If necessary the # bar may be
used to clear a previous entry if
a mistake is made.
• To enter a valid code, 10
seconds are allowed between
each button input; otherwise the
program will once again clear.
KitLock is a
Codelocks Ltd brand
www.codelocks.com
www.kitlock.com
SET OR CHANGE THE USER CODE
#Master Code
02
User Code
Example: #11335577
02
1455
Result: New User Code 1455 now operative.
• •
••
• • ••
DELETE USER CODE
#Master Code
03
Example: #11335577
03
Result: User Code deleted.
• ••
• ••
SET OR CHANGE THE SUB-MASTER CODE
#Master Code
04
Sub-Master Code
Sub-Master Code
Example: #11335577
04
22446688
22446688
Result: Sub-Master Code 22446688 now operative.
Note: # prefix not required when in B) Public Use.
• •
• •
•
•
DELETE THE SUB-MASTER CODE
#Master Code
05
05
Example: #11335577
05
05
Result: Sub-Master Code deleted.
Note: # prefix not required when in B) Public Use.
• • ••
• • ••
••
••
A) PRIVATE USE: CHANGING THE USER CODE
#User Code
New User Code
New User Code
Example: #2244
5541
5541
Result: User Code now 5541.
• •
• •
•
•
••
••
SET OR CHANGE THE USER CODE
#Sub-Master Code
07
User Code
Example: #11335500
07
9999
Result: New User Code 9999 now operative.
• •
• •
••
••
DELETE USER CODE
#Sub-Master Code
08
Example:#11335500
08
Result: User Code deleted.
• ••
• ••
•
•
•
•
••
••
B) PUBLIC USE: SET THE USER CODE
Enter personal four-digit code to lock Re-enter same code to open Note:
1. When the lock is opened the User Code will be erased and ready for
the next new user to enter their code. 2. When locked in B) Public Use Function the
LED will flash every two seconds indicating locked status. 3. Keypad in this function is only active when lever is in closed position.
•
••
•
CHANGING FROM B) PUBLIC USE TO A) PRIVATE USE
Master Code 11
Example: 11335577 11
Result: Lock will revert to A) Private Use with the default User Code 2244 active until
reprogrammed.
Note: When the program is changed from B) Public Use above to A) Private Use.
Use A) Private Use Function, the locking pin should now move to the locked position
and previous single User Code erased. The # bar will now be required for programming.
CHANGING FROM A) PRIVATE USE TO B) PUBLIC USE WITHOUT
A TECHNICIAN CODE
#Master Code
09
Example: #11335577
09
Result: The lock will now work in B) Public Use.
Note:
1. The locking pin is now programmed to be withdrawn when using the above
code string and is waiting and ready to accept a User Code. Please note that the
keypad is now inactive when the lever is in the open position.
2. Only the Master Code and Sub-Master Code will be retained from A) Private
Use Function.
SET THE LOCK IN TECHNICIAN MODE
Master Code 12 Technician Code Technician Code
Example: 11335577 12
555555
555555
Result: The lock set into Technician mode with Technician Code 555555
Note:
1. Technician Code only available when lock is set in B) Public Use.
2. The Technician Code is able to open the lock without the entered User Code
being erased.
3. Opening the lock with the Master Code will erase the User Code.
• •
• •
•
•
••
••
• ••
• ••
RESTRICT THE LOCKED TIME
Master Code
10
(number of hours lock to remain locked)
Example: 11335577
10
04
Result: The lock will auto open after 4 hours. If a new User Code is entered it
will once again relock for 4 hours.
If the lock is opened during the 4 hour period then the lock remains open until
a new User Code is entered as normal.
Note: This program will only work when the lock has been set into B) Public
Use Function. The two digits number of hours lock to remain locked is 02, 04,
06, 08, 10 or 12.
• •
• • ••
••
• ••
• ••
• •
• •
•
•
••
••
DELETE THE TECHNICIAN CODE
Master Code
13
13
Result: Technician Code deleted.
• • ••
DISABLE/ENABLE SOUNDER
The default is for the sounder to activate at every button press.
To disable the sounder enter the following toggle code string:
Master Code
14
14
Result: No sound when buttons pressed. To enable the sounder repeat above
code sequence.
• • ••
Vertical
••
CHANGING FROM A) PRIVATE USE TO B) PUBLIC USE WITH
TECHNICIAN CODE ENABLED
#Master Code
12
Technician Code
Technician Code
Example: #11335577
12
555555
555555
Result: The lock is automatically set into function B) Public Use AND allows
the programmed Technician Code to open the lock WITHOUT the entered User
Code being erased.
Note: If lock is opened with a Master Code the User Code will be erased.
KL12OO
••
SPECIAL MASTER CODE COMMANDS
•
•
SUB-MASTER CODE COMMANDS
CODELOCKS INC US
Tel: +1 714 979 2900
Fax: +1 714 979 2902
sales@codelocks.us
• •
• •
CHANGE THE SUB-MASTER CODE
#Sub-Master Code 06 New Sub-Master Code New Sub-Master Code
Example: #22446688
06
11335500
11335500
Result: Sub-Master Code has been changed to 11335500.
Note: # prefix not required when in B) Public Use.
USER CODE COMMANDS
Helpline, service & spares
FREEPHONE 0800 393 405
MASTER CODE COMMANDS
POI-KL1200- v2:0813
CODELOCKS LTD UK
Tel: +44 (0) 1635 239645
Fax: +44 (0) 1635 239644
sales@codelocks.co.uk
CHANGE THE MASTER CODE
#Master Code
01
New Master Code
New Master Code
Example: #11335577
01 12345678
12345678
Result: Master Code has been changed to 12345678.
Note: # prefix not required when in B) Public Use.
Programming
& Operating
Instructions
Open as PDF
Similar pages