SSA-EB Series Emergency Stop Push Buttons

SSA-EB Series Emergency Stop Push Button
Datasheet
Non-illuminated 30 mm mount electro-mechanical push buttons
•
•
•
•
•
•
•
•
•
•
•
Rugged design; easy installation with no assembly or individual wiring required
Push-to-stop, twist-to-release, or pull-to-release operation per IEC60947-5-5
Models with the washdown cover are push-to-stop and pull-to-release operation per
IEC60947-5-5
Latching design complies with ISO 13850; direct (positive) opening operation per IEC
60947-5-1
Compliant with ANSI B11.19, ANSI NFPA79, and IEC/EN 60204-1 Emergency Stop requirements
“Safe Break Action” ensures N.C. contacts will open if the contact block is separated from the
actuator
4-, 5-, or 8-pin M12/Euro-style Quick Disconnect
Models designed to interface with Safety BUS nodes/gateways
"Emergency Stop" legend included
U.S. Patent No. Des. 700,149
FDA-grade silicone cover withstands high pressure, high temperature washdown, and
increases the product rating to IP69K; the cover is ECOLAB® certified to withstand aggressive
cleaning procedures with chemicals used in the food processing industry
Models SSA-EB… series are "mushroom-style" electro-mechanical emergency stop push buttons. When the button is armed, the switch's
safety contacts (N.C.) are closed and its monitoring contacts (N.O.), if present, are open. When the button is pushed, the switch's safety
contacts open and the monitoring contacts close. The contacts remain in this condition until the push button is manually rearmed by
pulling or twisting clockwise the red push button actuator.
The SSA-EB1P.. and SSA-EB2P..ECQ.. series has a 30 mm mounting base similar to Banner’s OTB, VTB, and STB Optical Touch Buttons for
ease of mounting without requiring an additional enclosure.
Models
Model
SSA-EB1P-02ECQ4
SSA-EB1P-11ECQ4
Push Button
Standard 40 mm
E-Stop Contacts
2 N.C.
1 N.C. / 1 N.O.
Connection
4-pin M12 QD
Safety BUS node compatible1
SSA-EB1P-02ECQ5A
Standard 40 mm
SSA-EB2P-02ECQ5A
Large 60 mm
SSA-EB1P-02ECQ5B
Standard 40 mm
SSA-EB2P-02ECQ5B
Large 60 mm
SSA-EB1P-22ECQ8
Standard 40 mm
2 N.C. / 2 N.O.
SSA-EB2P-04ECQ8
Large 60 mm
4 N.C.
2 N.C.
5-pin M12 QD
CH1 = pins 1 & 2, CH2 = pins 4 & 5
Safety BUS node compatible2
2 N.C.
5-pin M12 QD
CH1 = pins 1 & 4, CH2 = pins 2 & 5
8-pin M12 QD
Washdown Cover Model
For Push Button Models
Description
SSA-EB1P-ECWC
Standard 40 mm
FDA-grade silicone cover
To order a model with the washdown cover installed, add "-WC" to the model number. For example, SSA-EB1P-02ECQ4-WC.
Important... Read this before proceeding!
The user is responsible for satisfying all local, state, and national laws, rules, codes, and regulations relating to the use of this product
and its application. Banner Engineering Corp. has made every effort to provide complete application, installation, operation, and
maintenance instructions. Please contact a Banner Applications Engineer with any questions regarding this product.
1 Compatible with AllenBradley ArmorBlock® 1732DS Safe DeviceNet remote I/O.
2 Compatible with Siemens ET 200pro PROFIsafe gateway.
Original Document
162755 Rev. F
15 March 2017
162755
SSA-EB Series Emergency Stop Push Button
The user is responsible for making sure that all machine operators, maintenance personnel, electricians, and supervisors are thoroughly
familiar with and understand all instructions regarding the installation, maintenance, and use of this product, and with the machinery it
controls. The user and any personnel involved with the installation and use of this product must be thoroughly familiar with all
applicable standards, some of which are listed within the specifications. Banner Engineering Corp. makes no claim regarding a specific
recommendation of any organization, the accuracy or effectiveness of any information provided, or the appropriateness of the provided
information for a specific application.
WARNING: Not a Safeguarding Device
An Emergency Stop Device is not considered a safeguarding device because it requires an overt action by an
individual to stop machine motion or hazards.
A safeguarding device limits or eliminates an individual's exposure to a hazard without action by the individual or
others. Because an individual must actuate the device for it to function, these devices do not fit the definition of a
safeguarding device and cannot be substituted for required safeguarding. Refer to the relevant standards to
determine those requirements.
Emergency Stop Considerations
ANSI NFPA 79, ANSI B11.19, IEC/EN 60204-1, and ISO 13850 specify emergency stop requirements, including the following:
• Emergency-stop push buttons shall be located at each operator control station and at other operating stations where
emergency shutdown is required.
• Stop and emergency-stop push buttons shall be continuously operable and readily accessible from all control and operating
stations where located. Do not mute or bypass E-stop buttons.
• Actuators of emergency-stop devices shall be colored red. The background immediately around the device actuator shall be
colored yellow (where possible). The actuator of a push-button-operated device shall be of the palm or mushroom-head type.
• The emergency-stop actuator shall be a self-latching type.
WARNING: Emergency Stop Functions
Do not mute or bypass any Emergency Stop device. ANSI B11.19, ANSI NFPA79 and IEC/EN 60204-1 require that
the Emergency Stop function remain active at all times.
WARNING: Multiple Switching Devices
Whenever two or more devices are connected to the same safety module (controller):
• Contacts of the corresponding pole of each switch must be connected together in series. Never connect
the contacts of multiple switches in parallel. Such a parallel connection defeats the switch contact
monitoring ability of the Module and creates an unsafe condition which may result in serious injury or
death.
• Each device must be individually actuated (engaged), then released (or re-armed) and the safety module
reset. This allows the module to check each switch and its wiring to detect faults.
This check must be performed during the prescribed checkouts. Failure to test each device individually in this
manner may result in undetected faults and create an unsafe condition which may result in serious injury or
death.
Installation and Maintenance
The device must not be affected by environmental conditions. Install the device so that operation is not impeded, but should be
protected against inadvertent operation (for example, accidental actuation by being bumped or leaned against). Do not operate the
switch using a tool. Do not expose the switch to excessive shocks and vibrations, otherwise the switch may be deformed or damaged,
causing malfunction or operation failure. Hardware includes jam nut, lock washer, lock ring, and seal washer. The lock ring may be used
to prevent switch rotation if a 5mm hole keyway is provided.
Electrical installation must be made by qualified personnel3 and must comply with NEC (National Electrical Code), ANSI/NFPA 79 or
IEC/EN 60204-1, and all applicable local standards. It is not possible to give exact wiring instructions for a device that interfaces to a
multitude of machine control configurations. The following is general in nature; it is recommended to perform a risk assessment to
ensure appropriate application, interfacing/hookup, and risk reduction (see ISO 12100 or ANSI B11.0).
3 A Qualified Person possesses a recognized degree or certificate or has extensive knowledge, training, and experience to solve problems relating to the emergency stop installation.
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 162755 Rev. F
SSA-EB Series Emergency Stop Push Button
WARNING: Shock Hazard and Hazardous Energy
Always disconnect power from the safety system (for example, device, module, interfacing, etc.) and the
machine being controlled before making any connections or replacing any component.
Electrical installation and wiring must be made by Qualified Personnel4 and must comply with the relevant
electrical standards and wiring codes, such as the NEC (National Electrical Code), ANSI NFPA79, or IEC 60204-1, and
all applicable local standards and codes.
Lockout/tagout procedures may be required. Refer to OSHA 29CFR1910.147, ANSI Z244-1, ISO 14118, or the
appropriate standard for controlling hazardous energy.
Table 1: SSA-EB1P-02ECQ4 (2 N.C.) and SSA-EB1P-11ECQ4 (1 N.C./1 N.O.)
Pin
Color
Function
Contacts
02ECQ4
1
Brown
CH1b
N.C.
N.C.
2
White
CH2a
N.C.
N.O.
3
Blue
Ch2b
N.C.
N.O.
4
Black
CH1a
N.C.
N.C.
5
n.a.
Pinout
11ECQ4
Male
1
2
4
5
3
n.a.
Table 2: SSA-EB1(2)P-02ECQ5A (2 N.C.) 5 and SSA-EB1(2)P-02ECQ5B (2 N.C.) 6
Pin
Color
1
02ECQ5A
02ECQ5B
Function
Contacts
Function
Contacts
Brown
CH1a
N.C.
CH1b
N.C.
2
White
CH1b
N.C.
CH2a
N.C.
3
Blue
n.c.
4
Black
CH2a
5
Gray
n.c.
N.C.
CH2b
N.C.
CH1a
CH2b
N.C.
N.C.
Pinout
Male
1
2
4
5
3
Table 3: SSA-EB2P-04ECQ8 (4 N.C.) and SSA-EB1P-22ECQ8 (2 N.C./2 N.O.)
Pin
Color
1
2
SSA-EB2P-04ECQ8
SSA-EB1P-22ECQ8
Function
Contacts
Function
Contacts
White
CH3a
N.C.
AUX1a
N.O.
Brown
CH4a
N.C.
AUX2a
N.O.
3
Green
CH3b
N.C.
AUX1b
N.O.
4
Yellow
CH2a
N.C.
CH2a
N.C.
5
Gray
CH2b
N.C.
CH2b
N.C.
6
Pink
CH1a
N.C.
CH1a
N.C.
7
Blue
CH4b
N.C.
AUX2b
N.O.
8
Red
CH1b
N.C.
CH1b
N.C.
Pinout
Male
1
2
3
4
7
6
8
5
Checkout
At machine set up, a Designated Person7 should test each emergency stop push button for proper machine shutdown response. A
Designated Person should check the emergency stop buttons for proper operation, physical damage, button looseness, and excessive
environmental contamination. This should take place on a periodic schedule determined by the user, based on the severity of the
4 A person who, by possession of a recognized degree or certificate of professional training, or who, by extensive knowledge, training and experience, has successfully demonstrated the ability
to solve problems relating to the subject matter and work.
5 Compatible with AllenBradley ArmorBlock® 1732DS Safe DeviceNet remote I/O
6 Compatible with Siemens ET 200pro PROFIsafe gateway
7 A Designated Person is identified in writing by the employer as being appropriately trained to perform a specified checkout procedure. A Qualified Person possesses a recognized degree or
certificate or has extensive knowledge, training, and experience to solve problems relating to the emergency stop installation.
P/N 162755 Rev. F
www.bannerengineering.com - Tel: +1-763-544-3164
3
SSA-EB Series Emergency Stop Push Button
operating environment and the frequency of switch actuations. Adjust, repair, or replace components as needed. If inspection reveals
contamination on the switch, thoroughly clean the switch and eliminate the cause of the contamination. Replace the switch and/or
appropriate components when any parts or assemblies are damaged, broken, deformed, or badly worn; or if the electrical/mechanical
specifications (for the environment and operating conditions) have been exceeded. Always test the control system for proper
functioning under machine control conditions after performing maintenance, replacing the emergency stop device, or replacing any
component of the device.
Installing the Silicone Cover
Follow these instructions to properly install the FDA-grade silicone cover.
1.
2.
3.
4.
Turn the cover inside-out, except for the top portion the button fits into.
Place the cover on top of the emergency stop unit.
Roll the cover onto the e-stop unit.
Continue rolling the cover down, around the base of the e-stop unit, until the
entire unit is covered.
Note: This cover is suitable for applications with pull-to-release
resetting methods.
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 162755 Rev. F
SSA-EB Series Emergency Stop Push Button
Specifications
Housing/Button
Polycarbonate / Polyamide
Threaded base has M30 x 1.5 external threads; Max. Tightening Torque: 4.5
N·m (40 in·lbf)
Operating Conditions
Temperature: –25 °C to +55 °C (−13 °F to +131 °F)
Humidity: 45% to 85% RH (no condensation)
Pollution Degree
3
Output Configuration
See Installation and Maintenance on page 2
Overvoltage Category
II
Environmental Rating
IP65 (IEC60529)
IEC IP67, IP69K per DIN 40050-9, and Type 4X (with SSA-EB1P-ECWC cover
installed)
Insulation Resistance
100 MΩ minimum (500 V dc megger)
Electrical Life
100,000 operations minimum, 250,000 operations minimum at 24 V AC/DC,
100 mA
Mechanical Life
250,000 operations
Shock Resistance
Operating extremes: 150 m/s2 (15G)
Impulse Withstand Voltage
2.5 kV
Vibration Resistance
Operating extremes: 10 to 500 Hz, amplitude 0.35 mm acceleration 50 m/s2
Contact Material/Bounce8
Gold plated silver / 20 ms
Required Overcurrent Protection
WARNING: Electrical connections must be made
by qualified personnel in accordance with local
and national electrical codes and regulations.
Overcurrent protection is required to be provided by end product application
per the supplied table.
Overcurrent protection may be provided with external fusing or via Current
Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
20
5.0
22
3.0
24
2.0
26
1.0
28
0.8
30
0.5
Electrical Rating
Minimum load: 1 mA at 5 V ac/dc
SSA-EB1(2)xx-..Q4 and -..Q5: 3 A at 250 V maximum
SSA-EB1(2)xx-..Q8: 2 A at 60 V ac/75 V dc maximum
UL Applications: 1.5 A at 250 V ac, 1 A at 30 V dc (pilot duty)
CE Applications: AC-15: 1.5 A at 250 V ac, DC-13: 1 A at 30 V dc
Rated Insulation Voltage (Ui)
250 V
Rated Current (Ith)
3A
B10d
100,000 (based on ISO13849-1(2006))
Design and Application Standards
Compliant with EN/IEC 60497-1 / -5-1, ISO 13850, ANSI B11.19 , ANSI NFPA79,
IEC 60204-1
Date code format (U.S. Standard Format)
YYWWX: 2-digit year, 2-digit week, "X” internal code
Certifications
Rated Operating Current and Voltage (Ue)
Safety Contact (N.C.)
30 V
125 V
250 V
Resistive Load (AC-12)
-
-
3A
Inductive Load (AC-15)
-
3A
1.5 A
AC 50/60 Hz
Resistive Load (DC-12)
2A
0.4 A
0.2 A
Inductive Load (DC-13)
1A
0.22 A
0.1 A
30 V
125 V
250 V
DC
Monitor Contacts (N.O.)
Resistive Load (AC-12)
-
1.2 A
0.6 A
Inductive Load (AC-14)
-
0.6 A
0.3 A
AC 50/60 Hz
Resistive Load (DC-12)
2A
0.4 A
0.2 A
Inductive Load (DC-13)
1A
0.22 A
0.1 A
DC
The operating current is classified according to IEC 60947-5-1 making and breaking capacities and are measured at resistive/inductive load types specified in IEC
60947-5-1. See "Electrical Rating" above for specific model and UL/CE maximum ratings.
8 When the button is reset, the normally closed contacts will chatter. When pressing the button, the normally open contacts will chatter. When designing a control circuit, take the contact chatter
time into consideration. Do not expose the switch to external shocks, otherwise the contacts will bounce.
P/N 162755 Rev. F
www.bannerengineering.com - Tel: +1-763-544-3164
5
SSA-EB Series Emergency Stop Push Button
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
33
[1.30]
59,5
[2.34]
80
[ 3.15 ]
5,0
[0.19]
30,0
[1.19]
Preferred
1/2 -14 NPSM
19
[.75]
12,7
[0.50]
32,8
[1.29]
119,8
[4.72]
10,0
[0.38]
Alternative
Hole Dimensions
M30 X 1.5
M12 X 1
Figure 1. Standard 40 mm Push Button
33
[1.30]
59,5
[2.34]
19
[.75]
80
[ 3.15 ]
5,0
[0.19]
12,7
[0.50]
32,8
[1.29]
119,8
[4.72]
1/2 -14 NPSM
10,0
[0.38]
30,0
[1.19]
Preferred
Alternative
Hole Dimensions
M30 X 1.5
M12 X 1
Figure 2. Large 60 mm Push Button
Dimensions of Washdown Silicone Cover SSA-EB1P-ECWC
6
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 162755 Rev. F
SSA-EB Series Emergency Stop Push Button
Accessories
Mounting Brackets
60
85
SSA-MBK-EEC1
• Single 30 mm hole
• 8 gauge steel, black finish
(powder coat)
• Front surface for customer
applied labels
80
45
B
A
SSA-MBK-EEC2
• Two 30 mm holes
• 8 gauge steel, black finish
(powder coat)
• Front surface for customer
applied labels
60
170
45
B
80
A
Hole size: A = ø 7 , B = ø 30
Hole size: A = ø 7 , B = ø 30
SSA-MBK-EEC3
• Three 30 mm holes
• 8 gauge steel, black finish
(powder coat)
• Front surface for customer
applied labels
60
255
B
80
A
Hole size: A = ø 7 , B = ø 30
60
85
45
SSA-MBK-EEC1-SS
• Single 30 mm hole
• 8 gauge 316 stainless steel
• Front surface for customer
applied labels
80
45
B
A
Hole size: A = ø 7 , B = ø 30
The SSA-MBK-EECx brackets offer:
• Horizontal and vertical (post) mounting
• Interchangeable positions of mounted devices (e.g. OTB/STB/VTB, EStop, K50s)
Cordsets
4-Pin Threaded M12/Euro-Style Cordsets
Model
Length
MQDC-406
1.83 m (6 ft)
MQDC-415
4.57 m (15 ft)
MQDC-430
Style
Dimensions
P/N 162755 Rev. F
M12 x 1
ø 14.5
15.2 m (50 ft)
www.bannerengineering.com - Tel: +1-763-544-3164
3
4
Straight
MQDC-450
2
1
44 Typ.
9.14 m (30 ft)
Pinout (Female)
1 = Brown
2 = White
3 = Blue
4 = Black
7
SSA-EB Series Emergency Stop Push Button
5-Pin Threaded M12/Euro-Style Cordsets—Double Ended
Model
Length
DEE2R-51D
0.31 m (1 ft)
DEE2R-53D
0.91 m (3 ft)
DEE2R-58D
2.44 m (8 ft)
DEE2R-515D
4.57 m (15 ft)
DEE2R-525D
7.62 m (25 ft)
DEE2R-550D
15.2 m (50 ft)
DEE2R-575D
22.9 m (75 ft)
Style
Dimensions
Pinout
Male
1
40 Typ.
2
4
5
3
Female Straight/
Male Straight
M12 x 1
ø 14.5
Female
2
44 Typ.
1
3
4
DEE2R-5100D
M12 x 1
ø 14.5
30.5 m (100 ft)
5
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Green/Yellow
8-Pin Threaded M12/Euro-Style Cordsets with Open-Shield
Model
Length
MQDC2S-806
1.83 m (6 ft)
MQDC2S-815
4.57 m (15 ft)
Style
Dimensions
Pinout (Female)
2
44 Typ.
MQDC2S-830
9.14 m (30 ft)
Straight
M12 x 1
ø 14.5
MQDC2S-850
3
4
1
7
6
15.2 m (50 ft)
8
1 = White
2 = Brown
3 = Green
4 = Yellow
5
5 = Gray
6 = Pink
7 = Blue
8 = Red
8-Pin Threaded M12/Euro-Style Cordsets―Double Ended
Model (8-pin/8-pin )9
Length
DEE2R-81D
0.31 m (1 ft)
DEE2R-83D
0.91 m (3 ft)
DEE2R-88D
2.44 m (8 ft)
DEE2R-815D
7.62 m (25 ft)
DEE2R-850D
15.2 m (50 ft)
Dimensions
Pinout
Female
2
Female Straight/
Male Straight
8
1
44 Typ.
2
3
4
22.9 m (75 ft)
1 = White
2 = Brown
3 = Green
4 = Yellow
30.5 m (100 ft)
5
Male
M12 x 1
ø 14.5
M12 x 1
ø 14.5
DEE2R-8100D
3
4
1
7
6
40 Typ.
4.57 m (15 ft)
DEE2R-825D
DEE2R-875D
Style
7
6
8
5
5 = Gray
6 = Pink
7 = Blue
8 = Red
See Banner Engineering catalog or www.bannerengineering.com for additional models and complete information.
Series Hookup Cordset Solution
This interconnection solution allows for quick hookup of a series of string emergency stop buttons. For the models listed below, Branch
#1 and Branch #2 are 300 mm (12 in) in length and the length of the trunk is listed below.
9 Standard cordsets are yellow PVC with black overmold. For black PVC and overmold, add suffix "B" to model number (example, DEE2R-81DB)
8
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 162755 Rev. F
SSA-EB Series Emergency Stop Push Button
WARNING: Intentional Defeat
The CSS Series Hookup Cordsets must be installed so that they cannot be easily defeated. Ensure that mounting
and routing of the cordsets that are connected to the Trunk, Branch #1, Branch #2, and the E-Stop QD connector
does not allow access to the QD connectors or allow improper connection bypassing the function of the Emergency
Stop.
+24V dc
0V dc
ES-FA-11AA
A2
A1
6 = CH1a (Pink)
5 = CH2b (Gray)
4 = CH2a (Yel)
8 = CH1b (Red)
1 = NO AUX1a (Wht)
2 = NO AUX2a (Brn)
S11
S21
S22
S12
13
Machine
Control
3 = NO AUX1b (Grn)
7 = NO AUX2b (Blu)
Model
Length
CSS-M12F41M12M41M12F41
0.30 m (1 ft)
CSS-M12F43M12M41M12F41
0.91 m (3 ft)
CSS-M12F48M12M41M12F41
2.44 m (8 ft)
S34
K1 K2
14
23
24
31
32
n.c.
M1
M2
M1
M2
Description
4-pin M12 QD splitter cordset for use with SSAEB1P-02ECQ4
SSA-EB1P-O2ECQ4
E-Stop # 1
SSA-EB1P-O2ECQ4
E-Stop # 2
3 1
3 1 5 4 2
4 2
4-Pin M12 Female TRUNK
CSS-M12F41M12M41M12F41
CSS-M12F43M12M41M12F41
CSS-M12F48M12M41M12F41
5-Pin M12 Female
DEE2R-5xxD
5-Pin M12
Male
2
4
5
1
3
P/N 162755 Rev. F
S33
RESET
Monitoring Circuit
4-Pin M12
Female
BRANCH #2
4-Pin M12
Male
BRANCH #1
4-Pin M12
Female/Flying Leads
MQDC-4xx
2
4
2
4
2 = CH2a (White)
4 = CH1a (Black)
1
3
1
3
1 = CH1b (Brown)
3 = CH2b (Blue)
www.bannerengineering.com - Tel: +1-763-544-3164
9
SSA-EB Series Emergency Stop Push Button
Model
Length
CSS-M12F81M12M81M12F81
0.30 m (1 ft)
CSS-M12F83M12M81M12F81
0.91 m (3 ft)
CSS-M12F88M12M81M12F81
2.44 m (8 ft)
SSA-EB1P-22ECQ8
E-Stop # 2
3 1 5 8
Description
8-pin M12 QD splitter cordset for use with SSAEB1P-22ECQ8
SSA-EB1P-22ECQ8
E-Stop # 1
3 1 5 8
6 4 2 7
6 4 2 7
8-Pin M12 Female TRUNK
CSS-M12F81M12M81M12F81
CSS-M12F83M12M81M12F81
CSS-M12F88M12M81M12F81
8-Pin M12 Female
DEE2R-8xxD
8-Pin M12
Male
8-Pin M12
Female
BRANCH #2
8-Pin M12
Male
BRANCH #1
4
6
2
7
8
5
1
3
4
6
2
7
8
5
1
3
4
6
2
7
8
5
1
3
Ø4.5
[0.18"]
44 Typ.
[1.73"]
18.0
[0.71"]
8-Pin M12
Female/Flying Leads
MQDC25-8xx
4 = CH2a (Yel)
6 = CH1a (Pink)
2 = NO AUX2a (Brn)
7 = NO AUX2b (Blu)
8 = CH1b (Red)
5 = CH2b (Gray)
1 = NO AUX1a (Wht)
3 = NO AUX1b (Grn)
44 Typ.
[1.73"]
Ø14.5 [0.57"]
Ø14.5 [0.57"]
Ø14.5 [0.57"]
M12 x 1
35 [1.38"]
43.0
[1.69"]
40 Typ.
[1.58"]
M12 x 1
U.S. Application Standards
ANSI B11.0 Safety of Machinery; General Requirements and Risk Assessment
ANSI B11.19 Performance Criteria for Safeguarding
ANSI NFPA 79 Electrical Standard for Industrial Machinery
International/European Standards
ISO 12100 Safety of Machinery – General Principles for Design — Risk Assessment and Risk Reduction
ISO 13850 (EN 418) Emergency Stop Devices, Functional Aspects – Principles for Design
IEC 62061 Functional Safety of Safety-Related Electrical, Electronic and Programmable Control Systems
ISO 13849-1 Safety-Related Parts of Control Systems
10
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 162755 Rev. F
SSA-EB Series Emergency Stop Push Button
IEC 60204-1 Electrical Equipment of Machines Part 1: General Requirements
IEC 60947-1 Low Voltage Switchgear – General Rules
IEC 60947-5-1 Low Voltage Switchgear – Electromechanical Control Circuit Devices
IEC 60947-5-5 Low Voltage Switchgear – Electrical Emergency Stop Device with Mechanical Latching Function
EU Declaration of Conformity (DoC)
Banner Engineering Corp. herewith declares that the SSA-EB1P.. and SSA-EB2P.. Emergency Stop Push Button is in conformity with the
provisions of the Machinery Directive (Directive 2006/42/EC), Low Voltage Directive (2014/35/EU) and all essential health and safety
requirements have been met.
Representative in EU: Peter Mertens, Managing Director Banner Engineering Europe. Address: Park Lane, Culliganlaan 2F, 1831 Diegem,
Belgium.
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover
damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY
OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT
DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the
product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the
product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time.
Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to:
www.bannerengineering.com.
© Banner Engineering Corp. All rights reserved
Open as PDF
Similar pages