Noirot Panel Heater Digital Timer Instructions

Noirot
Spot Plus
Digital Timer
Electric Convection Panel Heater
Operating & Installation
Instructions
In Order To Qualify For Your
Lifetime Warranty
Please Visit our Website and complete the Online Registration
www.noirot.com.au
RECOMMENDATION FOR WALL INSTALLATION
This heater is sold ready for DIY installation, with Wall bracket and flexible cord supplied. To
remove the wall bracket from the heater you need to push down on the spring loaded clips
located at the top of the bracket. This can be done by using your fingers or, if preferred, a
screwdriver (No: 1 Fig.1). Fit the wall bracket to the wall with suitable fixing method according to
the surface you mount the heater on (not included). Place the heater on to the bracket and clip
into position.
Note: To centre your appliance laterally on the wall, use the hole marked 2.
Fig. 1
Model
7358-3T
7358-5T
7358-7T
7358-8T
Height
440
440
440
440
A
420
580
745
900
B
208
178
320
405
C
106
201
210
248
The heater must not be located immediately below a socket outlet (as per requirement of
Clause 7.12 of AS/NZS 60335.2.30).
2
www.noirot.com.au
For maximum efficiency, this heater is to be
wall mounted between a minimum height of
100mm and a maximum height of 150mm off
the floor. This is to allow the necessary
volume of air to flow freely through the vents.
It is also important to allow a minimum of
100mm clearance at the top and sides of the
heater and 500mm from the front (Fig. 2) so
as not to force the air back into the heater
and activate the Over Temperature Safety
Thermal Cut-Out Switch.
WARNING: IN
ORDER
TO
AVOID
OVERHEATING,
DO
NOT
COVER THE HEATER
Fig. 2
If the “Over Temperature Safety Thermal Cut-Out Switch” is activated, the heater will
automatically switch off to limit the temperature to a safe value. To reset the thermal cut-out,
simply switch the heater off, unplug it from the power point and remove the obstruction(s). Plug
the heater back in and switch it on. The thermal cut-out switch will reset after a few minutes and
the heater will function normally.
PANEL LOCATIONS
This heater is suitable for use in all rooms including Zone 2 in Bathrooms (Fig.3) in accordance
with AS/NZS 3000: 2000 (Wiring Rules). Although this heater is double insulated and does not
require earthing, for use in the bathroom it must be located so that the controls cannot be
touched by a person in the bath or shower.
Fig. 3
www.noirot.com.au
3
RECOMMENDATION FOR USE WITH CASTORS
This heater is tested and approved for use with the optional “Easy Glide Castors”. Please follow
the fitting instructions (supplied with the castors) closely, ensuring the BLACK CLIPS are
correctly installed. Note that once the BLACK CLIPS are fixed into position, the castors
CANNOT be removed without breaking them.
WARNING: DO NOT use the heater on the floor without the “Easy Glide Castors”.
ELECTRICAL CONNECTION
This heater is fitted with an Australian Approved Flexible Cord and Plug. For wall-mounted
installations connection can be either by plugging into an existing 10 amp power point (DIY) or
direct wired by a Licensed Registered Electrical Contractor, who is required to issue a Certificate
of Electrical Safety.
PLEASE NOTE: For safety reasons the Flexible Cord must not be modified or repaired in any
way. If the Cord is damaged, it must be replaced by a Noirot appointed and approved service
agent. If there are any concerns, contact Noirot Australia Pty Ltd on 1 300 664 768 before
plugging it in.
IMPORTANT:
DO NOT plug heater into a Power Board, Double Adaptor or Extension
Lead.
USING YOUR HEATER FOR THE FIRST TIME
Remove the heater from its packaging (please dispose of packaging responsibly).
Contents should be as follows:
1. Heater
2. Wall bracket (pre-attached to the back of the heater)
3. Instructions for installation and use (8 page booklet)
Ensure the heater is correctly mounted on the wall or fitted to the castors prior to turning it on.
Remove the white plastic protective covers from the plug pins and insert the plug into the wall
socket.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
NOTE: When the heater is turned on for the first time, or after it has been off for a long period,
such as during the summer months, you may experience a slight burning smell. This is quite
common and should disappear after a few minutes. If it should persist, switch the heater off and
have it inspected.
4
www.noirot.com.au
THE MR190 DIGITAL CONTROLLER
On/Standby
Increase
Program
Mode Selector
On/Standby:
Mode Selector:
Decrease
Press
to turn the heater ON or return it to STANDBY Mode
The MODE button enables the heater to operate in the following 3 modes
(shown by the different symbols along the bottom of the display:
Mode
TIMER
Display
Description
Heater operates only during heating
periods
COMFORT
Heater operates continuously at the set
temperature
FROST-PROTECTION
Heater operates continuously at 7°C
(frost-protection)
MANUAL HEATER OPERATION
Ensure your heater is correctly installed or mounted on castors, plugged in and turned on at the
power point on.
Press
to turn the heater ON and ensure the mode is set to COMFORT.
Use the
and
buttons to set the required room temperature. The temperature is
increased or decreased in 0.5°C increments and ranges from 11°C to a maximum of 27°C.
The
symbol on the display indicates that the element is energised. Once the room
temperature has stabilised, the heating element will cycle on and off to maintain the room
temperature.
Press
to return the heater to STANDBY mode
SETTING THE TIME
Press the
button.
Press the
button for 2 seconds to enter the programming mode
The Day will now be blinking
Press the
button again, this time for 3 seconds to enter the time setting mode
The Hour will now be flashing
Use the
and
buttons to set the current hour, then press
to confirm
The Minutes will now be flashing.
Use the
and
buttons to set the current hour, then press
www.noirot.com.au
to confirm
5
The Day will now be flashing.
Set the current day (i.e. 1 for Monday, 2 for Tuesday, etc.), then press
to confirm.
The time and day are now set.
To display the current time during normal operation, briefly press the
button.
The time will be displayed for 3 seconds.
PROGRAMMING THE TIMER
It is possible to set up to 3 On/Standby periods per day using the timer mode. Each day can be
programmed individually or all days can be programmed at once.
Press the
button for 2 seconds to enter the programming mode
The Day will now be blinking
Use the
and
buttons scroll to the required day. Note that after Day 7, ‘ALL’ will be
displayed. Use this setting to program every day.
Press the
button to confirm
No. of the
period
Period 1 settings are now displayed
Use the
and
buttons to select the time that you
want the heater is to turn ON.
When a time is displayed a red triangle appears on the
display below FROM
Press the
button to confirm
Use the
button to select the time that you want the
heater is to return to STANDBY
The red triangle in now displayed below TO, indicating the
time the heater is set to revert to STANDBY mode.
Press the
button to confirm
Period 2 settings are now displayed. Repeat the above steps for Period 1 to set the times that
the heater is to turn ON and return to STANDBY.
If no more On/Standby periods are required for the day, continue to
again displayed.
press until the Day is
Repeat the above steps for each day heating periods are required.
To exit to programming mode press
until EXIT is display on the display.
Press the
until the DAY is displayed. Press the
button
button to confirm to exit programming
Briefly pressing the
button when the heater is in AUTO Mode will display the time left in a
heating period or the lapsed time until the next heating period starts. No Pr is displayed if no
more heating periods are programmed for that day.
Note:
6
The temperature can be adjusted at any time during a heating period. Simply press the
or
buttons to adjust the room temperature.
www.noirot.com.au
CHILD LOCK
Press both the
and
buttons together until the
is displayed on the screen.
This indicates that the child lock is activated, disabling the buttons on
keypad.
To re-activate the keypad, press both
the
and buttons together
disappears
the
until
the
key
MAINTENANCE
Your Noirot Electric Panel Heater requires very little maintenance. To remove surface dust use a
soft cloth; to remove marks use a damp cloth. Never use abrasives or metal scourers which
could damage the polyester coating. It is recommended to periodically clean the air vents using
the soft brush on your vacuum cleaner, as dense accumulation of dust will cause the heater to
over-heat and trigger the safety thermal cut-out switch.
SPECIFICATIONS:
Model
Power (W)
Current (A)
Height
A
B
C
7358-3T
1000
4.2
440
420
208
106
7358-5T
1500
6.3
440
580
178
201
7358-7T
2000
8.3
440
745
320
210
7358-8T
2400
10.0
440
900
405
248
Please note:
Heater temperature settings will vary from house to house according to the
building type and its level of insulation. They will also vary from room to room, depending on
factors such as room orientation (facing north or south) and window sizes. Items such as
computers and lights (which generate heat) and people will also affect a room’s temperature.
Running costs are not wholly governed by the temperature setting on the panel heater. The
same maximum power is used to reach 11° or 27°. Where the energy efficiency and economy is
obtained is in the sizing of the heater to the particular room where it is to be used. If the heater
is sized correctly, then the thermostat will cycle on & off as required to maintain your comfort
level, no matter where on the scale your comfort setting is.
www.noirot.com.au
7
WARRANTY REGISTRATION:
IMPORTANT: To validate your product warranty, you are required to do the following:
1. Register your product online at www.noirot.com.au, click on “Product Registration” and
fill out the required fields.
2. You must also retain your receipt of purchase
WARRANTY CONDITIONS
Your Noirot Spot Plus electric panel heaters comes with a LIFETIME WARRANTY, therefore
any replacement of faulty parts or repairs of any kind must be carried out by a qualified person
and authorised by Noirot Australia Pty Ltd or their approved representative. Failure to do so will
VOID the WARRANTY.
Noirot Australia Pty. Ltd. reserve the right to reject any warranty claim deemed to be false.
Retailers must have warranty claims authorised by a representative of Noirot Australia.
If you believe your product to be faulty and under warranty you are required to do the following:
1. Return the product, at your expense, to the place of purchase for assessment by an
authorised representative of Noirot Australia.
2. This may require leaving the product at the place of purchase.
3. If the product is deemed faulty and under warranty, the place of purchase of the
product will order a replacement heater to which Noirot Australia, at our cost, will
deliver the heater to the place of purchase.
4. The consumer will then be required, at their cost, to pick up the replacement heater
from the place of purchase.
5. If the heater is faulty but not deemed to be under warranty, an explanation will be
provided to the consumer and that the faulty heater can be picked up by the customer
from the place of purchase.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
If you have any queries regarding your product or its warranty please contact:
Noirot Australia Pty Ltd
80-84 Burlington St
Oakleigh Victoria 3166
Australia
P: 1 300 664 768
E: sales@noirot.com.au
8
Noirot New Zealand Pty Ltd
19B Orbit Drive
Rosedale Auckland 0622
New Zealand
P: (09) 476-7981
E: sales@noirot.co.nz
www.noirot.com.au
Open as PDF
Similar pages