2009 Xterra Quick Reference Guide

SHIFT_your limits
2009
XTERRA
QUICK REFERENCE GUIDE
LOW TIRE PRESSURE WARNING
LIGHT
TRIP COMPUTER
STEERING WHEEL SWITCHES FOR
AUDIO CONTROL/BLUETOOTH姞
CRUISE CONTROL
INSTRUMENT BRIGHTNESS
CONTROL/TRIP CHANGE BUTTON
HEADLIGHT AND TURN SIGNAL
CONTROL
WINDSHIELD WIPER/WASHER
SWITCH
MIRROR CONTROL SWITCH*
*See your Owner’s Manual for more information.
OFF ROAD LAMPS SWITCH (behind
steering wheel)
STEERING WHEEL TILT ADJUSTMENT*
HOOD RELEASE*
AUDIO SYSTEM
MANUAL CLIMATE CONTROL
FRONT-PASSENGER AIR BAG STATUS LIGHT
FOUR-WHEEL DRIVE (4WD) SHIFT
SWITCH
E-LOCK SWITCH
HILL DESCENT CONTRO
L SWITCH
VEHICLE DYNAMIC CONTROL
(VDC) OFF SWITCH
AUXILIARY AUDIO INPUT JACK
(if so equipped)*
TABLE OF CONTENTS
Remote Keyless Entry System (if so equipped) . . . . . . . . .
Automatic Door Locks . . . . . . . . . . . . . . . . . . . . . . .
Windshield Wiper/Washer Switch . . . . . . . . . . . . . . . .
Headlight and Turn Signal Control . . . . . . . . . . . . . . . .
Off Road Lamps (if so equipped) . . . . . . . . . . . . . . . . .
Steering Wheel Switches for Audio Control/Bluetooth姞
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Climate Control . . . . . . . . . . . . . . . . . . . . . .
FM/AM/XM姞* Radio with CD Changer (if so equipped). . . .
Clock Set/Adjustment . . . . . . . . . . . . . . . . . . . . . . .
Trip Computer (if so equipped) . . . . . . . . . . . . . . . . . .
Instrument Brightness Control/Trip Change Button . . . . . .
Four-Wheel Drive (4WD) Shift Switch (if so equipped) . . . .
Vehicle Dynamic Control (VDC) Off Switch (if so equipped) .
E-Lock Switch (if so equipped) . . . . . . . . . . . . . . . . . .
Hill Descent Control Switch (if so equipped) . . . . . . . . . .
Hill Start Assist (if so equipped). . . . . . . . . . . . . . . . . .
Front-Passenger Air Bag Status Light . . . . . . . . . . . . . .
Tire Pressure Monitoring System (TPMS) . . . . . . . . . . . .
Seat Belt Warning Light and Chime . . . . . . . . . . . . . . .
Child Safety Rear Door Lock . . . . . . . . . . . . . . . . . . .
Front Seat Adjustments . . . . . . . . . . . . . . . . . . . . . .
Fold Flat Front Passenger Seat (if so equipped) . . . . . . . .
Folding the Second Row Bench Seat . . . . . . . . . . . . . .
Channel Tie Down Hooks (if so equipped) . . . . . . . . . . .
Bluetooth姞 Hands-Free Phone System (if so equipped). . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.2
.2
.3
.3
.4
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .4
. .5
. .6
. .7
. .9
. .9
.10
.10
.10
.11
.11
.11
.12
.12
.12
.13
.13
.13
.14
.14
.14
This easy-to-use Quick Reference Guide is intended to help you more fully
appreciate some of the unique features and functions of your new vehicle.
However, it is not intended to replace your Owner’s Manual. The Owner’s
Manual contains more detailed information to help you better understand the
important safety warning, features, operation and maintenance of your
vehicle. All information, specifications, photographs and illustrations in this
publication are those in effect at the time of printing. NISSAN reserves the
right to change specifications or design without notice and without obligation.
REMOTE KEYLESS ENTRY SYSTEM (if so equipped)
LOCK DOORS
button to lock all doors.
Press the
UNLOCK DOORS
button once to unlock the driver’s
Press the
door only. Press the button again within 5 seconds
to unlock all doors.
USING THE PANIC ALARM
Press and hold the
button for longer than 0.5 seconds. The panic alarm will
sound and the headlights will stay on for 25 seconds. The panic alarm stops when
it has run for 25 seconds or when any button is pressed on the keyfob.
SILENCING THE HORN BEEP FEATURE
䡲 To deactivate: Press and hold the
䡲 To activate: Press and hold the
and
and
buttons for at least 2 seconds.
buttons for at least 2 seconds.
AUTOMATIC DOOR LOCKS
䡲 All doors will be locked automatically when the vehicle speed reaches 15 MPH (24
km/h).
䡲 All the doors will unlock automatically when the ignition switch is placed in the OFF
position.
The automatic lock and unlock functions can be deactivated or activated independently of each other. To deactivate or activate the automatic door lock or unlock
system, perform the following procedure:
1. Close all doors.
2. Place the ignition switch in the ON position.
3. Do one of the following within 20 seconds of performing Step #2:
● To change AUTO UNLOCK settings: push and hold the power door lock switch to
the
position (UNLOCK) for more than 5 seconds.
● To change AUTO LOCK settings: push and hold the power door lock switch to
the
position (LOCK) for more than 5 seconds.
4. When activated, the hazard indicator will flash twice. When deactivated, the hazard
indicator will flash once.
5. The ignition switch must be placed in the OFF and ON position again between each
setting change.
2
WINDSHIELD WIPER/WASHER SWITCH
䡲 The ignition switch must be in the ON position to
activate the windshield wipers.
䡲 Move the lever to the following positions to operate the windshield wipers:
Intermittent (INT) – Front wipers operate
intermittently and can be further adjusted by
.
twisting the time control ring
Low Speed (LO) – Continuous low-speed
operation of front wipers.
High Speed (HI) – Continuous high-speed
operation of front wipers.
Mist (MIST) – Lift the lever up for one sweep of the front wipers.
Rear Wipers (REAR) – Twist the end section to operate the first (INT) or second
(ON) speed settings for the rear wipers.
䡲 The washer function activates the washer fluid and several sweeps of the wipers:
● For FRONT WASHER, pull lever toward you.
● For REAR WIPER, push lever away from you.
HEADLIGHT AND TURN SIGNAL CONTROL
HEADLIGHT CONTROL SWITCH
䡲 Turn the headlight control switch
to the
position to turn on the front parking, tail, license plate
and instrument panel lights.
䡲 Turn the headlight control switch
to the
po-
sition to turn on the headlights. All other lights remain
on.
FOG LIGHT OPERATION (if so equipped)
䡲 Turn the switch (inside collar)
to the
䡲 Turn the switch (inside collar)
to the OFF position to turn off the fog lights.
position to turn on the fog lights.
3
HIGH BEAM
䡲 Push the headlight control switch forward
to se-
lect the high beam function. The blue
indicator
light illuminates. Pull the headlight switch back to the
original position to select the low beam. The blue
indicator light goes off.
䡲 Pull and release the headlight control switch
to flash the headlight high beams on
and off.
OFF ROAD LAMPS (if so equipped)
The roof rack mounted off road lamps are designed
to increase visibility when driving during off road
conditions. The off road lamps should not be used on
public roads.
To turn on the off road lamps:
䡲 The covers must be removed from the off road
lamps.
䡲 The headlights must be set to the high beam
function.
䡲 Push the OFF ROAD LAMPS switch.
To turn off the off road lamps:
䡲 Push the OFF ROAD LAMPS switch again.
䡲 If the high beam function of the headlights is turned off at any time, the
off road lamps will turn off as well.
䡲 If the high beam function is turned back on, the OFF ROAD LAMPS switch must be
pressed again for the off road lamps to turn on.
STEERING WHEEL SWITCHES FOR AUDIO CONTROL/
BLUETOOTH姞 (if so equipped)
䡲 Press the MODE button to turn the radio system on.
䡲 To choose Preset A, B, C, CD, AUX or XM姞 (if so equipped)
press MODE repeatedly.
䡲 The tuning up or down
switch can be used to perform the
following:
● Push the
switch for less than 1.5 seconds to change to a
preset station.
4
● Push and hold the
switch for more than 1.5 seconds to seek the next or previous
broadcasting radio station.
● Push the
switch while playing a CD (if so equipped) for less than 1.5 seconds to
change tracks on the CD.
● If the vehicle is equipped with a CD changer, push and hold the
switch for more
than 1.5 seconds to change between CDs.
䡲 Push the VOL control switch up or down to increase or decrease the volume.
CRUISE CONTROL
䡲 To activate the cruise control, push the ON·OFF switch. The
indicator light in the instrument panel will illuminate.
䡲 To set cruising speed, accelerate the vehicle to the desired
speed, push the COAST/SET switch and release it. The SET
indicator light in the instrument panel will illuminate.
䡲 To reset at a faster cruising speed, push and hold the
ACCEL/RES switch. When the vehicle attains the speed you
desire, release the switch.
䡲 To reset at a slower cruising speed, push and hold the COAST/SET switch. Release
the switch when the vehicle slows to the desired speed.
䡲 To cancel cruise control, push the CANCEL switch or tap the brake pedal. The SET
indicator light in the instrument panel will go out.
䡲 To resume a preset speed, push and release the ACCEL/RES switch. The vehicle
returns to the last set cruising speed when the vehicle speed is over 24 MPH (38 km/h).
䡲 To turn off cruise control, push the ON·OFF switch. Both the CRUISE indicator light and
the SET indicator light in the instrument panel will go out.
5
04
05
06
01
02
03
07
08
MANUAL CLIMATE CONTROL
FAN SPEED CONTROL DIAL
Turn the fan speed control dial
to the left (slow) or right (fast) to control fan speed.
TEMPERATURE CONTROL DIAL
Turn the temperature control dial for the desired temperature. Turn the control dial to the
left for cold air or right for hot air.
AIR FLOW CONTROL BUTTONS
Press the corresponding buttons to select the following air flow outlets:
Air flows from the center and side vents.
Air flows from the defroster outlets and the front and rear floor outlets.
Air flows from the center and side vents and the front and rear floor outlets.
Air flows mainly from the front and rear floor outlets.
DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
䡲 Press the defroster button
. The A/C automatically turns on when the defroster
mode is selected.
䡲 Turn the temperature control dial left or right to set the desired temperature.
䡲 To set the defroster on high, turn the fan speed dial all the way to the right.
DEFROSTING/DEFOGGING REAR WINDOW
Press the rear window defroster button
to turn the rear defroster on. Press the
button again to manually turn the defroster off. This function automatically turns off in
approximately 15 minutes.
6
AIR RECIRCULATION BUTTON
䡲 Press the air recirculation button
to recirculate air inside the vehicle.
䡲 Press the air recirculation button
again to turn air recirculation off.
䡲 The air recirculation mode can only be selected if the air flow control mode is in the
following positions:
or
.
A/C ON/OFF BUTTON
Press the A/C button to manually turn the A/C on or off.
MAX A/C ON/OFF BUTTON
Press the MAX A/C button for maximum cooling. Air flows from the center and side
vents.
FM/AM/XM姞* RADIO WITH CD CHANGER (if so equipped)
PRESET A·B·C BUTTON
Press the PRESET A·B·C button until you reach the desired setting. The radio is
equipped with three separate banks, each with six station presets. You may store any
combination of FM, AM or XM姞 radio presets on each bank.
SEEK/TRACK BUTTON
䡲 To scan quickly through each broadcasting station, press the SEEK/TRACK button.
䡲 To skip from one track to another on a CD, press the SEEK/TRACK button. Each
time the button is pressed, the CD will advance or skip back one track.
7
AUX BUTTON
Press the AUX button to play a compatible device such as an MP3 player when it is
plugged into the auxiliary jack.
NOTE: You may need to adjust the volume on any compatible device plugged into the
auxiliary jack to find the most desired sound level of the audio system.
SCAN/RPT BUTTON
Press the SCAN/RPT button to stop at each broadcasting station (FM, AM or XM姞) for
5 seconds. Pressing the button again during this 5-second period will stop scan tuning
and the radio will remain tuned to that station. If the SCAN/RPT button is not pressed
within 5 seconds, scan tuning moves to the next station.
CAT/FOLDER BUTTON
䡲 To manually tune the radio, press the CAT/FOLDER button.
䡲 When the CAT/FOLDER button is pressed while a CD is playing, it will fast forward
or rewind. When the button is released, the CD will play at normal speed.
䡲 MP3 PLAYBACK (if so equipped)
In addition to playing audio CDs, the audio system can play MP3 files recorded on
CD-ROM, CD-R, and CD-RW discs. Each disc can have a maximum of 8 folder
levels and 255 folders. A total of 512 MP3 files can be played back. During MP3
playback, some recorded ID3 tag information can be displayed by pressing the DISP
CLOCK button. Use the CAT/FOLDER button to navigate the MP3 folders.
EJECT BUTTON
䡲 EJECT A SINGLE DISC - Press the
button for less than 1.5 seconds. Select the
eject slot by pressing the CD insert select button (1 - 6 ). The CD will then eject.
䡲 EJECT ALL DISCS - Press and hold the
button for more than 1.5 seconds. The
CDs will be ejected one after another.
TUNING AND AUDIO CONTROL KNOB (Bass, Treble, etc.)
To manually tune the radio, turn the TUNE knob. To adjust the Bass, Midrange, Treble,
Fade, Balance, and Speed Sensitive Volume (SSV) (if so equipped), press the AUDIO
knob until the desired mode appears in the display. Then turn the TUNE knob to adjust
to the desired level.
STATION AND CD SELECT BUTTONS
䡲 To store a station in a preset you must first select A, B, or C memory bank by pressing
the PRESET A·B·C button and tune to the desired FM, AM or XM姞 station. Then
press and hold the desired station select button for at least 2 seconds. When the
preset indicator illuminates, a beep will sound, indicating memorization is complete.
To retrieve a previously set station, select the memory bank where the preset was set,
then press the corresponding station select button.
䡲 While playing a CD, to select a different CD loaded into the CD changer; press one
of the CD select buttons (1 - 6 ).
8
LOAD BUTTON
䡲 LOAD A SINGLE DISC - Press the
button for less than 1.5 seconds. Select
the loading slot by pressing one of the CD insert select button (1 - 6 ), then insert the
CD.
䡲 LOAD UP TO 6 DISCS - Press and hold the
button for more than 1.5 seconds.
The slot numbers (1-6) will illuminate on the display when CDs are loaded into the
changer.
*XM姞 Satellite Radio is only available on vehicles equipped with optional XM姞 satellite
subscription service.
CLOCK SET/ADJUSTMENT
䡲 Press and hold the DISP CLOCK button until it beeps. The hours will start flashing.
䡲 Press the CAT/FOLDER or SEEK/TRACK button to adjust the hours.
䡲 Press the DISP CLOCK button to switch to the minute adjustment.
䡲 Press the CAT/FOLDER or SEEK/TRACK button to adjust the minutes.
䡲 Press the DISP CLOCK button to store the time and exit clock set mode.
TRIP COMPUTER (if so equipped)
The trip computer readout is in the speedometer display. With
the ignition key in the ON position or the vehicle running, you
can select an item by pressing the CHANGE button on the
instrument panel. It can show the following items:
䡲 TRIP “A” – Measures the distance of one specific trip.
䡲 TRIP “B” – Measures the distance of a second specific
trip.
䡲 DISTANCE TO EMPTY (dte) – Estimates the distance that can be driven before
refueling.
䡲 AVERAGE SPEED (km/h or mph) – Shows the average speed since the last reset.
䡲 AVERAGE FUEL CONSUMPTION (l/100km or mpg) – Shows the average fuel
consumption since the last reset.
䡲 JOURNEY TIME – Shows the time since the last reset.
䡲 RESET – Press the CHANGE button on the instrument panel for more than 1 second to
reset the trip odometer to zero.
9
INSTRUMENT BRIGHTNESS CONTROL/TRIP CHANGE BUTTON
䡲 The instrument brightness control operates when the headlight control switch is in the
or
position.
䡲 Turn the control to adjust the brightness of the instrument panel lights.
䡲 Press the change button to select trip computer features.
FOUR-WHEEL DRIVE (4WD) SHIFT SWITCH (if so equipped)
䡲 This system provides three positions so the driver can select
the desired drive mode according to driving conditions.
䡲 2WD – Dry, paved roads.
䡲 4H – Rocky, sandy or snow-covered roads. (Before placing
4WD shift switch in 4H position from 2WD, ensure vehicle
speed is less than 62.5 MPH [100 km/h]).
䡲 4LO – When maximum power and traction are required
(steep grades, rocky, sandy or muddy roads).
NOTE: The vehicle must be stopped and in N (Neutral) with the brake pedal depressed
when shifting into and out of 4LO.
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped)
The Vehicle Dynamic Control (VDC) system monitors driver inputs and
vehicle motion. Under certain conditions, it controls braking and engine
output to help improve traction or handling. VDC may need to be
temporarily shut off if you are trying to free a vehicle stuck in snow or mud.
䡲 Push the Vehicle Dynamic Control (VDC) OFF switch to deactivate
the VDC system. The
gauge area.
light will illuminate in the instrument panel
䡲 Push the Vehicle Dynamic Control (VDC) OFF switch again to activate the VDC system.
The
light in the instrument panel gauge area will turn off.
䡲 The VDC system is active while the vehicle is running, until the switch is pressed to turn
it off.
10
E-LOCK SWITCH (if so equipped)
The Electronic Locking Rear Differential (E-Lock) system can
help provide added traction if the vehicle is stuck or becoming
stuck.
To activate the system:
䡲 The 4WD switch must be in the 4LO position (4-wheel
drive vehicles),
䡲 The vehicle must be stopped or moving at 4 mph or less,
and
䡲 The E-Lock system switch must be turned on.
Once the vehicle is free, the system should be turned off.
HILL DESCENT CONTROL SWITCH (if so equipped)
The hill descent control system is designed to reduce driver
workload when going down steep hills. The hill descent control
system helps to control vehicle speed so the driver can concentrate on steering the vehicle.
To activate the hill descent control system:
䡲 The automatic transmission selector lever must be in forward or reverse gear,
䡲 The 4WD switch must be in the 4L position and the vehicle
speed must be under 15 MPH (25 km/h), or
䡲 The 4WD switch must be in the 4H position and the vehicle speed must be under 21
MPH (35 km/h), and
䡲 The hill descent control system switch must be on.
䡲 The hill descent control indicator light will come on when the system is activated. Also,
the stop/tail lights illuminate while the hill descent control system applies the brakes to
control vehicle speed. To turn off the hill descent control system, push the switch to the
off position. The hill descent control system is temporarily disabled when the brake or
accelerator pedal is depressed.
HILL START ASSIST (if so equipped)
The hill start assist system automatically keeps the brakes applied to help prevent the vehicle
from rolling backwards in the time it takes the driver to release the brake pedal and apply the
accelerator when the vehicle is stopped on a hill. The maximum holding time is 2 seconds.
Hill start assist will operate automatically under the following conditions:
䡲 The selector lever is shifted to a forward or reverse gear.
䡲 The vehicle is stopped completely on a hill by applying the brake.
11
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air Bag System.
Under some conditions, depending on the type of occupant or object
detected in the front passenger seat by the occupant classification
sensor, the front-passenger air bag is designed to automatically turn
OFF. When the front-passenger air bag is OFF, the front-passenger
air bag status light will illuminate*. For example:
䡲 When the system detects that the front-passenger’s seat is
occupied by a small adult, child or child restraint as outlined in
will illuminate to indicate that the front-passenger air
the Owner’s Manual, the
bag is OFF and will not inflate in a crash.
䡲 When the front-passenger’s seat is occupied and the passenger meets the conditions
will not illuminate to indicate that the
outlined in the Owner’s Manual, the
front-passenger air bag is operational.
*When the system detects that the front-passenger’s seat is unoccupied, the
passenger air bag status light will not illuminate even though the front-passenger
air bag is OFF.
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tire pressure. If the low tire pressure warning
light illuminates, check the tire pressure in all four tires.
Adjust the low tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label located in the
driver’s door opening. After tire pressures are adjusted, the vehicle
will need to be driven at speeds above 16 MPH (25 km/h) to activate
the TPMS and turn off the low tire pressure warning light.
SEAT BELT WARNING LIGHT AND CHIME
䡲 The light and chime remind you to fasten your seat belts.
The light illuminates whenever the ignition switch is placed
in the ON or START position and remains illuminated until
the driver’s seat belt is fastened. At the same time, the
chime sounds for approximately 6 seconds unless the
driver’s seat belt is securely fastened.
䡲 The seat belt warning light may also illuminate if the front
passenger’s seat belt is not fastened when the front passenger’s seat is occupied (if so equipped). For 7 seconds
after the ignition switch is in the ON position, the system does not activate the warning
light for the front passenger.
12
CHILD SAFETY REAR DOOR LOCK
䡲 The child safety lock levers are located on the edge of the rear doors.
䡲 Child safety locks help prevent the rear doors from being opened
accidentally, especially when small children are in the vehicle.
䡲 When the lever is in the LOCK position, the door can only be opened
from the outside.
FRONT SEAT ADJUSTMENTS
䡲 Pull up on the lever under the front of the
seat and slide forward or backward. Release the lever to lock the seat in position.
䡲 Lift the lever
on the side of the seat to
adjust your seatback forward or backward;
release when you have found a comfortable
angle and the seat belt fits properly.
SEAT LIFTER (if so equipped)
䡲 Turn either dial
to adjust the angle and height of the seat cushion to the desired
position.
LUMBAR SUPPORT (if so equipped)
Move the lever
forward or backward to
adjust the lumbar support.
FOLD FLAT FRONT PASSENGER SEAT (if so equipped)
To fold the front passenger’s seatback flat for
extra storage length when transporting long
items:
䡲 Slide the seat to the rearmost position. Lift
, located on the
up on the recline lever
outside edge of the seat, and fold the seatback forward as far as it will go.
䡲 Lift up on the latch
located on the upper corner of the seatback to release the back
of the seat.
䡲 Once the seatback is released, it will enable you to fold the front passenger seatback flat
over the seat cushion.
13
FOLDING THE SECOND ROW BENCH SEAT
To fold the 2nd row bench seat flat for maximum
cargo hauling:
䡲 Lower the head restraints to the full “down”
located in the
position. Pull the strap
center of each seat cushion forward, and
fold each seat cushion toward the front of
the vehicle.
䡲 Then pull the straps
located on the
outside edge of each seatback to fold the
seatbacks forward.
CHANNEL TIE DOWN HOOKS
The adjustable channel tie-down hook system
allows you to move the tie-down hooks in the
cargo area to the best location to secure a load.
BLUETOOTH姞 HANDS-FREE PHONE SYSTEM (if so equipped)
With an overhead microphone and sound
transmitted through the audio system
speaker, the Bluetooth姞 Hands-Free Phone
System utilizes Bluetooth姞 wireless technology and voice recognition to provide handsfree cellular phone communication.
SYSTEM OPERATING TIPS
䡲 Close all windows. Surrounding noises
may interfere with system operation and
performance.
䡲 Press the
14
button on the steering wheel to activate voice recognition.
䡲 Wait for the tone before speaking.
䡲 Begin speaking a command within 5 seconds of the tone.
䡲 To go back to the previous command, say “Go back” or “Correction.”
䡲 To cancel a voice recognition session, simply wait 5 seconds, say “Cancel” or “Quit,” or
press the
button.
䡲 To increase or decrease the volume of the voice prompts, push the VOL (volume) control
switch up or down on the steering wheel or turn the VOL knob on the audio system while
the system is responding.
䡲 Speak in a clear and natural voice without pausing between words.
䡲 If the Voice Recognition system does not recognize your voice commands, train the
system using the Speaker Adaptation Mode. Refer to your Owner’s Manual for a list of
commands and further instructions.
䡲 Some commands are not available while the vehicle is in motion.
䡲 The “Help” command can be used in any menu to hear a list of available commands.
䡲 Please refer to the cellular phone manufacturer Owner’s Manual for detailed information
regarding your Bluetooth姞 phone.
䡲 For recommended phones and detailed instructions, please visit
www.nissanusa.com/bluetooth .
PAIRING YOUR PHONE
To use the hands-free feature, you need to set-up, or pair, the system to recognize your
compatible cellular phone(s). Five Bluetooth姞-enabled phones can be paired. After set-up,
the system automatically connects with a paired phone when the ignition is in the ACC or ON
position, as long as the phone is on and in the vehicle.
PAIRING PROCEDURE
NOTE: The vehicle must be stationary when pairing the phone.
1. Press the
button on the steering wheel and wait for the tone.
2. Say “Setup”.
3. Wait for the tone, then say “Pair phone”.
4. Wait for the tone, then say “New phone”.
5. Initiate pairing from the phone.
䡲 The pairing procedure varies according to each cellular phone model. For detailed
pairing instructions and a list of compatible phones, please visit
www.nissanusa.com/bluetooth .
䡲 When prompted for a PASSKEY code, enter “1234” from the handset. (The PASSKEY code is assigned by NISSAN and cannot be changed.)
6. Say a name for the phone when the system asks you to provide one. You can give the
phone a name of your choice.
15
7. Say a number between 1 and 5 when the system asks you for a priority level. The
priority level determines which phone interacts with the system when two or more
paired phones are active in the vehicle at the same time. Choose 1 if this is the only
phone or the primary phone.
8. Say “Yes” or “No” when the system asks if you would like to select a custom ring tone.
Follow the instructions provided by the system to choose a ring tone.
SETTING UP YOUR PHONEBOOK – ADDING NEW ENTRIES
Each paired phone has its own dedicated phonebook. Each phonebook can store up to 40
names. Each name can have up to 4 locations/numbers: Home, Office, Mobile, and Other.
NOTE: The vehicle must be stationary when adding new entries.
1. Press the
button and wait for the tone.
2. Say “Phonebook”.
3. Wait for the tone, then say “New entry”.
4. When prompted, say the name for the new entry. For example, say “Michelle”. If the
name is too short or too long, or if it sounds too much like a name that is already
stored in the phonebook, the system tells you and prompts you to say a name again.
Choose a new name.
5. Say “Yes” or “No” when the system asks you to confirm the name is correct.
6. Say a location (“Home,” “Office,” “Mobile” or “Other”) when the system asks you to
provide one. The system acknowledges the location.
䡲 By Voice command - When prompted, say a phone number for the location. For
example, say “five five five one two one two”. The system repeats the number and
prompts you for the next command.
䡲 By Bluetooth姞 transfer - Say “Transfer entry”. The system acknowledges the command and asks you to initiate the transfer from the phone handset. The new contact
phone number will be transferred from the cellular phone via the Bluetooth姞 communication link. The transfer procedure varies according to each cellular phone. See the
cellular phone owner’s manual for details.
7. Say “Store” when you are finished entering numbers. The system confirms the name,
location, and number.
8. Say “Yes” or “No” when the system asks if you would like to store another location for
the same name. If you do not respond to the system prompt, the system ends the
New Entry session.
MAKING A PHONE CALL
1. Press the
button.
2. After the tone, do one of the following:
䡲 Say “Call [name] [location]”. For example, say “Call Michelle Home”.
䡲 Say “Call [number]”. For example, say “Call 123-456-7891”.
䡲 Say “Redial” to redial the previous phone number called by the system.
16
䡲 Say “Call International” to dial more than 10 digits or any special characters.
RECEIVING/ENDING A PHONE CALL
When you receive a phone call, a ring tone sounds through the audio system.
䡲 To accept the call, press the
button. To reject the call, press the
button.
䡲 To hang up the phone at the end of a call or to disconnect during call placement, press
the
button.
HOW TO SAY NUMBERS
NISSAN voice recognition permits numbers to be spoken in a variety of ways.
䡲 Say “zero” or “oh” for “0”. Example: 1-800-662-6200 – Say “one eight zero zero six six
two six two oh oh”.
䡲 Say “pound” for “#”. Say “star” for “*” (available when using the “Call International”
command, and the “Send” command during a call).
䡲 Say “plus” for “+” (available only when using the “Call International” command).
䡲 Say “pause” for a 2 second pause (available only when storing a phonebook number).
17
SHIFT_
Nissan, the Nissan Brand Symbol, ⬙SHIFT_⬙ tagline, Z and Nissan model names are Nissan trademarks.
© 2008 Nissan North America, Inc.
QR9E-0N50U0
Printing: June 2008 (08)
Open as PDF
Similar pages