Swing Door Operators EMSW EMO

TM
Swing Door Operators
EMSW EMO
Silent and Suitable Everywhere
The EMSW EMO is one of the most silent operators in
the market. It is an ideal solution for i.e. healthcare, residential, office & public service environments where both
low-noise and ease of access are important. Its low-energy performance is compliant with DDA requirements.
The operator functions reliably under varying conditions
and climate changes.
World–class Safety
The EMSW EMO is a perfect choice for hospitals and
assisted living facilities for the elderly or disabled. Its
power-assist feature allows the door to be opened with
only a slight push. The highly intelligent operator senses
the presence of an obstruction during opening and stops
or reverses direction. These features provide a high
degree of safety at a very reasonable cost.
If optionally equipped with external safety sensors, the
EMSW EMO operator monitors the sensors every time it
opens or closes the door. If the sensors are not functioning properly, the automation is deactivated and the door
will function as a manual swing door with a door closer.
Intelligent locking technology
Want to use an electronic lock? There are several intel-
ligent functions that ensure that the EMO senses if the
door is fully closed and properly locked. When it detects
that the door has not completely closed, the EMSW
EMO will prompt the door to open again and close fully.
The operator also features intelligent double-door functionality for use with rebated (overlapping) swing doors
and will always close the doors in the right order so that
they are fully closed, latched and can be locked.
Cost Efficiency
The EMSW EMO’s motor is equipped with an electronic
door brake that controls the door’s speed when it is unexpectedly blown or forcefully pushed toward the open or
closed position. This unique feature reduces the wear and
tear, limiting breakdowns.
The modern motor control in the EMSW EMO minimizes
the energy consumption so that the power required to open
a 90 kg door is even lower than to light a 25W lamp!
Back-Up when Power Failure
In the event of a power failure, the operator can be activated by battery power via a key impulse that opens
the door once, then closes and locks it before switching
off. This unique technology ensures that the entrance is
accessible independent of power.
110 mm
130 mm
Pushing arm system, PUSH
110 mm
130 mm
Models
- Single operator – one drive unit and one
control unit fitted un­der a cover
- Double operator – two drive units with
control units fitted un­der the same cover
for ope­ration of two doors
Arm systems
- Pushing arm system PUSH – The
operator is installed on the wall on the
opposite side of the door swing. Door
open­ing angle adjustable up to 110°
- Pulling arm system PULL – The operator is installed on the wall on the same
side as the door swing. Door ­open­ing
angle adjustable up to 110°
- Pulling arm system ST-V/H – Used in
windy conditions when the operator is
installed on the wall on the same side
as the door swing. Door opening angle
adjustable up to 90°
- Drive shaft extensions – Allow the ope­
rator to be fitted higher on the wall or
the arm lower on the door leaf
Standard equipment
- Cover – manufactured in clear anodized
aluminium. End plates made of black
painted steel sheet
Dimensions:
Height 110 mm
Depth 130 mm
Single operator: Length 716 mm
Special length covers up to 1600 mm
Double operator: Length optional
- Control unit CU-ESD – with possibility to connect manual and auto­matic
activation units, position switches and
overhead presence detectors (OPD)
- “Push and go” – the door opens automatically from closed position if manually pushed
- Power assist – the motor gives power
assist when the door is opened by hand
Accessories
- Extension unit EXU-SI – Used if additional functions are required, e.g. electro-mechanical lock, program selector,
emergency battery, kill function open/
close, key opening and outer impulse
- Extension unit EXU-SA – Has inputs
for both monitored /non monitored door
mounted sensors, which can give presence impulse and/or presence detection.
Relay output for error or door indication
is also integrated.
- Sync cable – Used on double doors to
select the opening and closing order
- Finger trap protection devices
- Manual and automatic activation units
- Impulse and presence detection s­ ensors
- Programme selectors
- Monitored battery backup unit: 24 VDC
1200 mA
- Electromechanical locking connection:
12 VDC max 500 mA or 24 VDC max
250 mA
Technical specifications
- Power supply: 100-240 V AC, +10/15%, 50/60 Hz
- Power consumption: max. 75 W
- Auxiliary voltage: 24 V DC, max. 400 mA
- Internal control fuse: 2 x T 6.3 AH 250 V
- Door leaf width: max. 1200 mm
- Recommended door weight: max. 90 kg
- Door opening angle: 80 - 110°
- Reveal: Push 0 - 100 mm (300 mm with
longer telescopic part) / Pull 0 - 130 mm
- Opening and closing time: variable
between 3 - 6 sec.
- Hold open time: 1.5 - 30 sec.
- Ambient temperature: -20°C to +45°C
- Relative humidity (non-condensing)
max 85%
- Class of protection: IP20 - to be
installed internally or externally with
suitable weather protection
Authority Approval
The EMSW EMO meets the following
requirements;
- SITAC SC0840-09
- TÜV B 09 09 70555 002
TM
DITEC Entrematic Nordic AB, Box 669, SE‑261 25 Landskrona Phone: +46 418 514 50 Fax: +46 418 511 63
info@ementrematic.se • www.ementrematic.com
1006856-EMEI-1.0 – Issue 2010-03-04 – Rights reserved for changes without prior notice.
© All rights in and to this material are the sole property of Entrematic AB. Copying, scanning, alterations or modifications are expressly forbidden without the prior written consent of Entrematic AB.
Pulling arm system, PULL
Open as PDF
Similar pages