TileVision® Interface Connections and Control Codes TV/19/FR1

TileVision® Interface Connections
and Control Codes
TV/19/FR1 & TV/26/FR1
IR Link Out & In
These enable control of external equipment via the IR sensor on
the TileVision® and control of the TileVision® from a remote location.
RJ12 Connector
This connector allows the TileVision® to be integrated with Interactive Hotel TV Systems.
RS-232 Port
This DB9 connector allows the TileVision® to receive command codes from
Home Automation Systems.
TileVision® Interface Connections
IR Links and RJ12 Connections
IR Link Out
IR Links
The IR Link Out is a 3.5mm mono jack socket. The IR signal sensed by the TileVision® is outputted from this socket to an
IR emitter. This will enable the remote control of external equipment, such as a DVD player, from the TileVision®.
IR Link Out Connections – IR Emitter
Tip Sleeve
IR emitter LED positive terminal to the Tip.
IR emitter LED negative terminal to the Sleeve.
3.5 mm mono jack plug
IR Link In
The IR Link In is a 3.5mm stereo jack socket. This socket allows an auxiliary IR sensor to be connected to the TileVision®
to enable remote control of the TileVision® from a different point other than the front of the TileVision®.
IR Link In Connections – IR Receiver
Tip
The TileVision® interface will supply +5v DC to power the IR sensor.
IR sensor +5v DC terminal to the Tip.
Ring
Sleeve
3.5 mm stereo jack plug
IR sensor signal output terminal to the Ring.
IR sensor negative terminal to the Sleeve.
RJ12 Connector
RJ12 Connections
This connector is for Hotel TV System Integration. The RJ12 allows command codes to pass to and from the TileVision®.
The RJ12 pin assignment is internally configurable, to allow the connection of various Hotel TV Systems.
RJ12 Connector – Standard Configuration
Pin No
1
2
3
4
5
6
Function
Not Connected
Command code from the external equipment to the TileVision® (0V/5V nominal)
Not Connected
TileVision® On signal from the TileVision® to the external equipment (On = 5V, Standby = 0V nominal)
0V – DC ground
Demodulated IR signal from the TileVision® IR sensor to the external equipment (0v/5v nominal)
1 6
1 6
Connector on the Interface PCB
1 6
Male RJ12 connector – front view
Male RJ12 connector – top view
IR Remote Control
IR Remote Control
The IR remote control uses the NEC protocol.
For a full listing of the IR remote control codes refer to page 4.
1
TileVision® Interface Connections
RJ12 Command Code Format
Command Codes via the RJ12 Connector
RJ12 Command Code Format
The codes in the table below are the codes that will be sent to the TileVision via the RJ12 connector.
The voltage levels that are accepted as an input on pin 2 of the RJ12 connector (command code from external
equipment to the TileVision®) are:
HIGH + 5 volts DC LOW 0 volts DC
Important: When the input on pin 2 of the RJ12 connector is inactive/idle it must be held HIGH. If pin 2 of the RJ12
connector is held low, all subsequent command codes via the RJ12 connector and via the TileVision® IR receiver (sent
from the TileVision® IR remote control) will fail and the TileVision® will be non responsive.
Pin 5 of the RJ12 connector is DC ground.
The code sequence sent to the RJ12 connector is a DEMODULATED NEC protocol format.
First Start Pulse LOW 9.0 ms.
Second Start Pulse HIGH 4.5 ms.
Logic 1 = LOW 560 µs HIGH 1.69 ms.
Logic 0 = LOW 560 µs HIGH 560 µs.
Stop Pulse LOW 560 µs.
Logic 1 – 2.25 ms
Logic 0 – 1.12 ms
Stop 560 µs
Inactive/idle
HIGH
Inactive/idle
HIGH
560 µs
Address
00FF
9 ms
Code
8D72
4.5 ms
2
TileVision® Interface Connections
RJ12 Command Codes – Address 00FF
Function
RJ12 Command Codes – Address 00FF
Power ON
Power Toggle ON/OFF (see note)
DTV
ATV
SCART
Component
PC – RGB
HDMI
Composite
S-Video
Input
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 9
Channel 0
CH + Channel Up
CH – Channel Down
Vol + Volume Up
Vol – Volume Down
Mute
Menu
U Navigation Up
D Navigation Down
L Navigation Left
R Navigation Right
Enter/OK
Exit
EPG
Red (Fast Text)
Green (Fast Text)
Yellow (Fast Text)
Blue (Fast Text)
Fav (Favourites)
Info (Information)
Pic (Picture Mode)
Sound (Sound Mode)
Aspect (Aspect Ratio)
Return (PLP/Previous Channel)
Audio
Subtitle
Sleep
Text
Index (Text)
List (Text)
Hold (Text)
Size (Text)
Reveal (Text)
Subpage (Text)
TV/Radio (DTV only)
Nicam (ATV only)
Note:
Hex Code
8
C
8
7
A
6
9
B
C
5
7
4
6
5
0
2
1
C
E
D
C
9
5
B
F
8
8
A
8
7
7
6
A
0
D
9
1
5
8
C
E
A
2
9
3
7
E
3
6
2
A
B
E
F
0
4
D
1
E
E
E
E
E
E
E
E
1
5
1
1
5
1
1
4
0
0
0
0
0
4
4
0
1
1
4
4
0
0
0
4
5
5
5
5
5
5
4
4
0
4
5
5
1
0
5
5
5
5
5
5
1
1
7
3
7
8
5
9
6
4
3
A
8
B
9
A
F
D
E
3
1
2
3
6
A
4
0
7
7
5
7
8
8
9
5
F
2
6
E
A
7
3
1
5
D
6
C
8
1
C
9
D
5
4
1
0
F
B
2
E
1
1
1
1
1
1
1
1
E
A
E
E
A
E
E
B
F
F
F
F
F
B
B
F
E
E
B
B
F
F
F
B
A
A
A
A
A
A
B
B
F
B
A
A
E
F
A
A
A
A
A
A
E
E
There is no discrete Power Off code, the
Power Toggle On/Of must be used to set
the TileVision® to standby.
Power Toggle On/Off will set the opposite
condition of the TileVision® as below.
TileVision® On – Power Toggle On/Off –
TileVision® set to Standby.
TileVision® Off – Power Toggle On/Off –
TileVision® set to On.
3
TileVision® Interface Connections
IR Remote Control Codes – NEC Protocol – Address 00FF
Function
IR Remote Control Codes – NEC Protocol – Address 00FF
Power ON
Power Toggle ON/OFF (see note)
DTV
ATV
SCART
Component
PC – RGB
HDMI
Composite
S-Video
Input
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 9
Channel 0
CH + Channel Up
CH – Channel Down
Vol + Volume Up
Vol – Volume Down
Mute
Menu
U Navigation Up
D Navigation Down
L Navigation Left
R Navigation Right
Enter/OK
Exit
EPG
Red (Fast Text)
Green (Fast Text)
Yellow (Fast Text)
Blue (Fast Text)
Fav (Favourites)
Info (Information)
Pic (Picture Mode)
Sound (Sound Mode)
Aspect (Aspect Ratio)
Return (PLP/Previous Channel)
Audio
Subtitle
Sleep
Text
Index (Text)
List (Text)
Hold (Text)
Size (Text)
Reveal (Text)
Subpage (Text)
TV/Radio (DTV only)
Nicam (ATV only)
Hex Code
D
1
E
E
E
E
E
E
E
E
1
5
1
1
5
1
1
4
0
0
0
0
0
4
4
0
1
1
4
4
0
0
0
4
5
5
5
5
5
5
4
4
0
4
5
5
1
0
5
5
5
5
5
5
1
1
8
C
8
7
A
6
9
B
C
5
7
4
6
5
0
2
1
C
E
D
C
9
5
B
F
8
8
A
8
7
7
6
A
0
D
9
1
5
8
C
E
A
2
9
3
7
E
3
6
2
A
B
E
F
0
4
2
E
1
1
1
1
1
1
1
1
E
A
E
E
A
E
E
B
F
F
F
F
F
B
B
F
E
E
B
B
F
F
F
B
A
A
A
A
A
A
B
B
F
B
A
A
E
F
A
A
A
A
A
A
E
E
7
3
7
8
5
9
6
4
3
A
8
B
9
A
F
D
E
3
1
2
3
6
A
4
0
7
7
5
7
8
8
9
5
F
2
6
E
A
7
3
1
5
D
6
C
8
1
C
9
D
5
4
1
0
F
B
To program an IR remote control to
transmit an IR signal to operate the
TileVision the codes in the table (left) must
be entered.
Note:
There is no discrete Power Off code, the
Power Toggle On/Of must be used to set
the TileVision® to standby.
Power Toggle On/Off will set the opposite
condition of the TileVision® as below.
TileVision® On – Power Toggle On/Off –
TileVision® set to Standby.
TileVision® Off – Power Toggle On/Off –
TileVision® set to On.
4
TileVision® Interface Connections
The RS-232 Port
RS-232 Port
The RS-232 Port
The RS-232 port is a DB9 male connector. This connector allows Home Automation Systems to send command codes
directly to the TileVision®.
The TileVision® will only receive RS-232 codes, it does not transmit codes. Only pin 2 (receive) and pin 5 (ground) are
connected in the DB9 male connector.
To connect to the RS-232 port a DB9 female connector must be used.
If a standard RS-232 port is to be connected to the TileVision® RS-232 port, pins 2 and 3 must be cross wired. So pin 3
(transmit) of the external equipment will be connected to pin 2 (receive) of the TileVision®.
RS-232 Protocol
Command Code Sequence
Baud Rate: 38400
A0 F0 55 FF <IR Code> <Check Sum>
Bits:
8
The time of the command sequence must be < 500 ms.
Parity:
None
The interval time of two continuous command sequences must be > 500 ms.
Stop Bit:
1
RS 232 Code Listing (Hex)
Function
Power ON
Power OFF
0
1
2
3
4
5
6
7
8
9
VOL+
VOLCH+
CHINPUT
DTV
ATV
HDMI
COMPONENT
S-VIDEO
SCART
COMPOSITE
PC
MUTE
MENU
IR Code
61
62
0C
54
16
15
50
12
11
4C
0E
0D
4B
4F
09
05
17
E8
E7
EB
E6
E5
EA
EC
E9
08
18
Check Sum
9F
9E
F4
AC
EA
EB
B0
EE
EF
B4
F2
F3
B5
B1
F7
FB
E9
18
19
15
1A
1B
16
14
17
F8
E8
Function
UP
DOWN
LEFT
RIGHT
ENTER
RETURN
EXIT
SOUND
PIC
ASPECT
SLEEP
TEXT
INFO
FAV
EPG
RED
GREEN
YELLOW
BLUE
REVEAL
HOLD
LIST
INDEX
SUBPAGE
SIZE
AUDIO
NICAM (ATV)
SUBTITLE (DTV)
IR Code
1A
48
47
07
06
49
0A
4A
4E
02
1E
03
5C
58
40
5D
59
51
55
5E
5A
52
56
5F
5B
53
14
57
Check Sum
E6
B8
B9
F9
FA
B7
F6
B6
B2
FE
E2
FD
A4
A8
C0
A3
A7
AF
AB
A2
A6
AE
AA
A1
A5
AD
EC
A9
5
Porter Lancastrian Limited
Lower Healey Business Park · Froom Street · Chorley · Lancashire · UK · PR6 9AR
Tel: 0870 871 0111 · Fax: 0870 871 0112
Sales: sales@porta.co.uk · Web: www.tilevision.tv
Control Codes 09/10
Open as PDF
Similar pages