Laminators PRO MS-A5 PRO MS-A4 PRO MS-A3 - pro

Laminators
PRO
PRO
PRO
PRO
PRO
USER MANUAL
MS-A5
MS-A4
MS-A3
MS-A3 +
MS-A2
PRO INTELLECT TECHNOLOGY LLC presents a series of professional laminators PRO
OFFICE LINE, designed for paper, document, photo laminating of A2, A3, A3 +, A4 Formats.
Laminators are with hot shafts of external heating, that provides uniform heating of the surface of
the shaft and the high quality lamination. Short heating time, the reverse function, the auxiliary
indicators of readiness, a smooth temperature adjustment knob provides ease of management
and use of a laminator. Metal housing "is guarantee of reliability and safety when working with
laminator. All laminators can do foiling. Models PRO MS A2; PRO MS A3 and PRO MS A3 +
have cold lamination function.
Specifications
Technical
characteristics:
PRO MS-A5
PRO MS-A4
PRO MS-A3
PRO MS-A3+
PRO MS-A2
Format
A5
A4
A3
A3+
A2
Width of lamination
160mm
230mm
310mm
330mm
450mm
Rate
lamination
350mm/min
650mm/min
650mm/min
650mm/min
650mm/min
Number of shafts
4
4
4
4
4
Voltage
220V/50Hz
220V/50Hz
220V/50Hz
220V/50Hz
220V/50Hz
Power
320W
420W
620W
620W
820W
Weight
5.3kg
6.2kg
7.7kg
8.0kg
11.0kg
Dimensions, mm
340x200x110
400x200x110
500x200x110
500x200x110
630x200x110
2
Appearance
the upper lid
Input tray
control panel
PRO MS-A2, PRO MS-A3+, PRO MS-A3
2
PRO MS-A4, PRO MS-A5
2
3
1
6
5
3
1
4
1. Temperature controller
2. The power indicator.
3. Indicator of readiness.
4. Power switch.
5. Switch feed direction (FWD "forward, REV" reverse).
6. The switch-type lamination (HOT "Hot, COLD" cold) *.
* Here and further: only models PRO MS "A2, PRO MS" A3 +, PRO MS "A3.
3
5
4
Instruction
• Before operating the laminator should be familiar with this instruction and comply with the
requirements.
• When removing the unit from its packaging must remove the tape (if available), fixing the power
cord.
• Be very careful to matches to the set temperature and the thickness used the film as otherwise
may lead to melting of the film.
• Do not place anything on top cover of the laminator and not touch the hot roll laminator and hot
parts of the body.
• Do not place the laminator at the following locations:
• on an inclined plane
• Damp location
• Where the equipment is subjected to vibration
• In a dusty room
• Where it is exposed to direct sunlight or direct exposure lighting
• Do not operate the laminator with wet hands
• Take precautions against falling into the laminator liquid foreign objects, insects
• Take precautions against accidental fall of the laminator
• Keep children away from laminator
• Do not leave the laminator power on unattended the operator.
• Before changing the location of the laminator cleaning or turn it off from the network and Wait
until it cools down (at least 1 hour).
• Do not operate the laminator if it is open the top cover is damaged body or the power cord
• To avoid accidents, do not expose hair, neckties, clothing and jewelry in the laminator.
• If you pull clothing, hair, and so on. Etc. a laminating machine, quickly move power switch to
"OFF" position or switch directions lamination in position "REV" or unplug the power cord.
• Do not open or attempt to repair the laminator yourself.
• Do not place in the output tray laminator nothing but paper documents
• Use a laminator at ambient temperature "of 18 to 25 ° C.
• If you experience the presence of strangers (tinny) sound may be bad an upper cover unit.
Replace the cover correctly. Attention! In continuous operation laminator more than 2 hours is
recommended to de at break for 20 minutes. Do not use the laminator for continuous operation
more than 4 hours. Improper operation of the laminator may overheat 4 parts of the laminator and
failure. Remember! For the possible consequences and problems resulting from incorrect
operation of the laminator manufacturer is not liable. Hot lamination. 1. Turn on the laminator,
turning the switch network in position "ON", while indicator lights up "POWER". In accordance
with the film thickness (See Table 1) Set the thermostat to the desired position (for models PRO
MS "A2, A3, A3 +, you must also set the type of lamination (hot or cold) through switch 6). Make
sure that the switch the direction of lamination was in position "FWD" (forward). After the green
LED "READY" (ready), the laminator is ready. 2. Insert laminiruemy sheet and place the package
in the output tray laminator exactly, glued edge first (see figure), the laminator will automatically
captures the packet and lamination. Laminations pack size smaller than the format laminator
need to install the package in output tray, aligning the center of the front edge of the package and
the middle of the receiver tray.
4
3. If you want to return the package back out of the laminator, click direction in the position "REV"
(reverse).
4. After completion of the work, slide the network in the "OFF"
Notes:
• listed in the table are average values and may vary Depending on the quality of the used film.
• The thickness of the film using should be chosen depending on the thickness of laminating
document for documents using a thick the film. For laminating photographs and film thickness
should be chosen 100mkm and above. For laminating photos, printed on matte textured paper
(canvas, satin) should be set to the temperature 10 "200C above.
• If the document is poorly laminated (sheets of film are not stuck or poorly stuck to each other,
the film does not become transparent), then increase the temperature
• If the output under the film turned out to be small air bubbles or film turned undulating surface,
then reduce heat.
• Hot lamination can be started only after the green
LED "READY". In the lamination process, he may flash as the unit equipped with a thermostat
that controls heating of the shaft during operation.
• The inner parts of the laminator are covered with a special compound, why, particularly, during
the first time, you may receive a characteristic smell.
• Try not to touch the inner surface of the film
Temperature dependence of the thickness of the film used
lamination and laminate package again.
Film Thickness (mm)
Temperature ° C
2х60
95-105
2х80
105-115
2х100
115-125
2х125
125-130
2х150
130-135
2х175
135-145
2х250
145-160
• Do not laminate the coins and other objects of the thick
• To extend the life of the laminator before turning off to leave the unit turned on at the lowest
temperature controller (80 ° C) or in a cold lamination for 3 "5 minutes (for laminators PRO "MS
A3, PRO MS" A3 +, PRO MS "A2).
1. Set the temperature to 120-140 degrees. And wait indicator lights up when ready "READY"
2. Place the foil is not color side on a sheet with the image or text the top. At the top of the foil
also put any piece of paper so that it fully covers it. Place the bag in the front pocket of the
laminator.
3. Remove the top sheet and gently not glued to a sheet of foil with image or text.
Cold lamination *
1. Set the temperature at the position of "COLD". Make sure that switch the direction of lamination
was in position "FWD" (forward).
5
2. Insert laminiruemy sheet in the package and place it in front "pocket" laminator glued edge first,
the unit will proceed to lamination.
3. If you want to return the package back out of the laminator, click direction in the position "REV".
4. After completion of the work, slide the network in the "OFF" Prophylaxis.
• Turn the switch network to the OFF position
• Unplug the power cord.
• Allow to cool laminator for 60 minutes.
• Remove the top cover, taking her two hands on the edge. On the format laminator A2 to remove
the cover to unscrew the 4 top screws.
• Clean the shaft using a special solution in alcohol, soft cloth.
• Do not use scouring powder or other abrasive cleaners.
• Do not wipe that "other than shafts.
• Place the lid on the apparatus. Indentations on ears cover should coincide with
projections on the walls of the housing.
• The unit can be used within 30 minutes.
WARRANTY
The manufacturer guarantees the correct operation unit during the warranty period from the date
of sale, subject to the rules of consumer usage and storage, outlined in this manual. After
extracting the device from the packaging store, please pack and User's Guide. Warranties are
void if the unit not sent in their original packaging or have been violated requirements operation
and maintenance. For device malfunction due to improper transportation of non-compliance with
the instructions, as well as non-compliance with safety precautions or of "mechanical damage,
Manufacturer is not liable. In the case of the device inoperable during the warranty period owner
is entitled to free repair service center. Equipment accepted in warranty repairs free of dust and
dirt. Cleaning equipment from the jammed piece of paper or foreign objects and dirt do not
warranty and is performed for a fee. The warranty does not include training in the use and
performance and functions to ensure the health technology (Connection, testing, adjustment,
maintenance work, etc.), which owner can perform, independently, in accordance with the
attached the instruction manual. Warranty service is not available in the following cases: "If there
is no warranty card incorrectly filled coupon and coupon having a fix. "If you violate the rules of
use of the product specified in the rules of operation and maintenance. "If there is mechanical
damage to the product. "If there are traces of tampering on the sealed product. "If the poor quality
of the lamination is the result of wrong the selected temperature. This warranty does not cover:
the network adapters, power supplies, adapters, cigarette lighters, lamps, batteries, belts, fuses,
brush, magnifying glass, remote design elements, part of the body products and any other parts
that have a limited period of natural efficiency, as well as any defects arising out of "the instability
of external conditions or accidents outlet. Replaced defective parts are our property. Delivery of
defective equipment to the Service Centre by dealers and at his expense.
6
7
Open as PDF
Similar pages