Operating Instructions
SIP Phone
Model No.
<KX-UT248>
KX-UT113/KX-UT123
KX-UT133/KX-UT136
KX-UT248
Thank you for purchasing this Panasonic product.
Please read this manual carefully before using this product and save this manual for future use.
KX-UT113/KX-UT123/KX-UT133/KX-UT136/KX-UT248: Software File Version 01.160 or later
In this manual, the suffix of each model number is omitted unless necessary.
Document Version: 2012-06
Introduction
Introduction
Feature Highlights
Easy Operation
You can easily access features using the Navigator key, fixed buttons, and soft buttons.
Also, the Message/Ringer lamp will inform you when you have an incoming call or a message waiting.
High-quality Voice Communication
This unit supports the standard SIP protocol and the G.722 codec, enabling reliable and high-quality voice
communication.
ECO Mode
Enabling ECO mode allows you to use this unit while reducing the amount of electricity consumed
(Page 41).
Compatible with Electric Hook Switch (EHS) Headsets (KX-UT133/
KX-UT136/KX-UT248 only)
The KX-UT133/KX-UT136/KX-UT248 supports EHS headsets (Page 64).
Compatible with Bluetooth® Wireless Headsets (KX-UT248 only)
The KX-UT248 supports Bluetooth wireless headsets (Page 64).
Outline
This manual describes information about the installation and operation of the unit.
Related Documentation
Getting Started
Briefly describes basic information about the installation of the unit.
Administrator Guide
Describes information about the programming and maintenance of the unit.
Manuals and supporting information are provided on the Panasonic Web site at:
http://www.panasonic.com/sip (for users in the United States)
http://panasonic.net/pcc/support/sipphone (for users in Canada)
Note
•
2
The contents and design of the software are subject to change without notice.
Operating Instructions
Document Version 2012-06
Introduction
Notes for Connecting to a Panasonic PBX
•
If KX-UT113/KX-UT123/KX-UT133/KX-UT136 is connected to a Panasonic KX-NS1000 PBX, refer to the
documentation of the KX-NS1000 for information about the operation, programming, and maintenance of
the unit. For details, consult your dealer.
However, please refer to this documentation for details about the following features:
– Phonebook (Page 25, 36)
– Call Log (Page 26)
Other Information
Trademarks
•
•
•
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by
Panasonic Corporation is under license.
Plantronics is a trademark or registered trademark of Plantronics, Inc.
All other trademarks identified herein are the property of their respective owners.
When you ship the product (For users in the United States only)
Carefully pack and send it prepaid, adequately insured and preferably in the original carton. Attach a
postage-paid letter, detailing the symptom to the outside of the carton.
DO NOT send the product to the Executive or Regional Sales offices. They are NOT equipped to make repairs.
Product Service (For users in the United States only)
Panasonic factory service centers for this product are listed in the service center directory.
Consult your authorized Panasonic dealer for detailed instructions.
Document Version 2012-06
Operating Instructions
3
Introduction
For Future Reference
Record the information in the space below for future reference.
Note
•
The serial number and MAC address of this product may be found on the label affixed to the bottom
of the unit. You should note the serial number and MAC address of this unit in the space provided and
retain this manual as a permanent record of your purchase to aid in identification in the event of theft.
MODEL NO.
SERIAL NO.
MAC ADDRESS
DATE OF PURCHASE
NAME OF DEALER
DEALER'S ADDRESS
DEALER'S TEL. NO.
4
Operating Instructions
Document Version 2012-06
Table of Contents
Table of Contents
Important Information ..............................................................................7
For Your Safety .................................................................................................................7
Data Security .....................................................................................................................9
Additional Information ....................................................................................................10
Before Operating the Telephone ..........................................................12
Accessory Information ...................................................................................................12
Location of Controls .......................................................................................................13
Screens ............................................................................................................................19
Status Icons .....................................................................................................................20
Soft Buttons and Soft Button Icons ..............................................................................21
Basic Operations .............................................................................................................23
Confirming Your Extension Number ...............................................................................23
Going off- and on-hook ...................................................................................................23
Adjusting the Volume .....................................................................................................24
Feature Operations ................................................................................25
Making Calls ....................................................................................................................25
Making a Call ..................................................................................................................25
Making a Call from the Phonebook List ..........................................................................25
Dialing by Using Call Logs .............................................................................................26
Redialing the Last Number You Dialed (Redial, Last Number) ......................................26
One-touch Dialing (KX-UT133/KX-UT136/KX-UT248 only) ...........................................26
Receiving Calls ................................................................................................................27
Receiving a Call .............................................................................................................27
Rejecting Calls ...............................................................................................................27
Holding a Call ..................................................................................................................29
Receiving a Second Call (Answering Call Waiting) .....................................................29
Talking to Two Parties Alternately (Call Splitting) .......................................................30
Transferring a Call (Call Transfer) .................................................................................30
To Transfer with One Touch (One-touch Transfer) (KX-UT133/KX-UT136/KX-UT248
only) ................................................................................................................................30
Mute ..................................................................................................................................31
Conference Call (Local Three-way Conference) ..........................................................32
Making a Conference Call ..............................................................................................32
Removing a Party from the Conference .........................................................................32
Ending a Conference Call ..............................................................................................32
Checking Messages ........................................................................................................33
Checking New Messages ...............................................................................................33
Checking Missed Calls ...................................................................................................33
Call Forwarding/Do Not Disturb .....................................................................................34
Logging in to or Logging out of a Group (KX-UT133/KX-UT136/KX-UT248
only) ..................................................................................................................................34
Logging in to or Logging out of an ACD (Automatic Call Distribution) Group .................34
To set/cancel Not Ready mode or to leave Wrap Up mode ...........................................34
Flexible Buttons (KX-UT133/KX-UT136/KX-UT248 only) .............................................35
Customizing the Telephone ..................................................................36
Phonebook List ...............................................................................................................36
Adding a New Phonebook Entry ....................................................................................36
Adding a Phonebook Entry from the Incoming or Missed Call Log ................................36
Editing a Phonebook Entry .............................................................................................36
Document Version 2012-06
Operating Instructions
5
Table of Contents
Searching for a Phonebook Entry ..................................................................................37
Deleting a Phonebook Entry ...........................................................................................37
Export/Import Phonebook Entries ..................................................................................37
User Settings ...................................................................................................................38
Accessing the Settings ...................................................................................................38
Available Settings ...........................................................................................................39
Settings Details ..............................................................................................................41
Entering Characters ........................................................................................................51
Web User Interface Programming .................................................................................59
Installation and Setup ............................................................................60
Attaching/Removing the Stand ......................................................................................60
Connections ....................................................................................................................63
Wall Mounting ..................................................................................................................67
Hooking the Handset ......................................................................................................72
Using a Headset ..............................................................................................................74
Setting Up the Unit ..........................................................................................................75
Maintaining the Unit ........................................................................................................76
Initializing the Unit ..........................................................................................................76
Restarting the Unit ..........................................................................................................76
Cleaning the Unit ............................................................................................................76
Appendix .................................................................................................77
Specifications ..................................................................................................................77
Troubleshooting ..............................................................................................................80
Common Issues and Solutions .......................................................................................80
Error Messages ..............................................................................................................84
Revision History ..............................................................................................................85
KX-UT113/KX-UT123/KX-UT133/KX-UT136 Software File Version 01.025 ..................85
KX-UT113/KX-UT123/KX-UT133/KX-UT136 Software File Version 01.080 ..................86
KX-UT113/KX-UT123/KX-UT133/KX-UT136/KX-UT248 Software File Version
01.160 ............................................................................................................................87
Open Source Software ...........................................................................88
Index..............................................................................................................92
6
Operating Instructions
Document Version 2012-06
Important Information
Important Information
For Your Safety
To reduce the risk of injury, loss of life, electric shock,
fire, malfunction, and damage to equipment or property,
always observe the following safety precautions.
Explanation of symbols
The following symbols are used to classify and describe
the level of hazard and injury caused when the
denotation is disregarded and improper use is
performed.
WARNING
Denotes a potential hazard that could result in
serious injury or death.
CAUTION
Denotes a hazard that could result in minor injury or
damage to the unit or other equipment.
The following symbols are used to classify and describe
the type of instructions to be observed.
This symbol is used to alert users to a specific
operating procedure that must not be
performed.
This symbol is used to alert users to a specific
operating procedure that must be followed in
order to operate the unit safely.
WARNING
General Safety
Do not disassemble this unit. Dangerous
electrical shock could result. The unit must
only be disassembled and repaired by
qualified service technicians.
Never attempt to insert wires, pins, etc. into
the vents or other holes of this unit.
To prevent possible fire or electric shock, do
not expose this unit to rain or moisture.
Do not splash water on the AC adaptor or the
power cord, nor get them wet.
Doing so can result in fire, electric shock, or
injury. If they do get wet, immediately
disconnect the AC adaptor and power cord,
and contact an authorized service center.
Do not touch the AC adaptor for extended
periods of time. Doing so can lead to
low-degree burns.
Unplug this unit from the AC outlet and have
the unit serviced by qualified service
personnel in the following cases:
A. When the power supply cord or plug is
damaged or frayed.
B. If liquid has been spilled on the unit.
C. If the unit has been exposed to rain or
water.
D. If the unit does not work normally by
following the manual. Adjust only controls
covered by the manual. Improper
adjustment may require repair by an
authorized service center.
E. If the unit has been dropped, or damaged.
F. If the unit’s performance deteriorates.
If damage to the unit exposes any internal
parts, immediately disconnect the cable or
cord. If the power is supplied from the network
to the SIP Phone [Power-over-Ethernet],
disconnect the Ethernet cables. Otherwise,
disconnect the AC adaptor cord. Then return
this unit to an authorized service center.
This handset earpiece is magnetized and may
retain small ferrous objects.
The use of excessive sound volume through
earphones, headphones, or headsets may
cause hearing loss.
Document Version 2012-06
Operating Instructions
7
Important Information
Disconnect this unit from power outlet/the
Ethernet cables if it emits smoke, an abnormal
smell, or makes unusual noise. These
conditions can cause fire or electric shock.
Confirm that smoke has stopped and contact
an authorized service center.
Installation
Do not make power connections that exceed
the ratings for the AC outlet or power
equipment. If the power rating of a surge
protector, etc. is exceeded, it can cause a fire
due to heat buildup.
Wall Mounting
Do not mount the unit in a manner other than
that described in this manual.
Make sure that the wall that the unit will be
attached to is strong enough to support the
unit. If not, it is necessary for the wall to be
reinforced. For information about the weight
of the unit, see "Specifications (Page 77)".
Do not bundle up the AC adaptor cord. The
cord may become damaged, which can lead
to a fire, electric shock, or electric short.
Only use the optional wall mount kit with the
unit. The wall mount kit includes the
necessary screws, washers, and wall
mounting adaptor.
The unit should only be connected to a power
supply of the type as shown on the label on
the unit.
When driving the screws into the wall, be
careful to avoid touching any metal laths, wire
laths or metal plates in the wall.
Completely insert the AC adaptor into the AC
outlet. Failure to do so may cause electric
shock and/or excessive heat resulting in a fire.
When this unit is no longer in use, make sure
to detach it from the wall.
Medical (KX-UT248 only)
Do not use the product in health care facilities
if any regulations posted in the area instruct
you not to do so. Hospitals or health care
facilities may be using equipment that could
be sensitive to external RF energy.
Consult the manufacturer of any personal
medical devices, such as pacemakers or
hearing aids, to determine if they are
adequately shielded from external RF (radio
frequency) energy (the product operates in
the frequency range of 2.402 GHz to
2.480 GHz and the power output is 2.5 mW
[max.]).
Placement
Care should be taken so that objects do not
fall onto, and liquids are not spilled into, the
unit. Do not subject this unit to excessive
smoke, dust, moisture, mechanical vibration,
shock, or direct sunlight.
Do not place heavy objects on top of this unit.
Place this unit on a flat surface.
8
Allow 10 cm (3 15/16 in) clearance around the
unit for proper ventilation.
Operating Instructions
CAUTION
Keep the unit away from heating appliances
and devices that generate electrical noise,
such as fluorescent lamps, motors and
televisions. These noise sources can interfere
with the performance of the unit. It also should
not be placed in rooms where the temperature
is less than 0 °C (32 °F) or greater than 40 °C
(104 °F).
Wipe the unit with a soft cloth. Do not clean
the unit with abrasive powders or with
chemical agents such as benzine or thinner.
The handset hook poses a choking hazard.
Keep the handset hook out of reach of
children.
When left unused for a long period of time,
disconnect the unit from the AC outlet. When
the unit receives power from a PoE power
supply, disconnect the Ethernet cables.
When the unit is mounted on a wall, make
sure the cables are securely fastened to the
wall.
Document Version 2012-06
Important Information
Notice
•
•
•
•
•
•
If the unit does not operate properly, disconnect
the AC adaptor cord and Ethernet cables and
then connect again.
If you are having problems making calls,
disconnect the Ethernet cables and connect a
known working SIP Phone. If the known working
SIP Phone operates properly, have the
defective SIP Phone repaired by an authorized
service center. If the known working SIP Phone
does not operate properly, check the SIP server
and the Ethernet cables.
Under power failure conditions, the SIP Phone
may not operate. Please ensure that a separate
telephone, not dependent on local power, is
available for use in remote sites in case of
emergency.
For information regarding network setup of the
SIP Phone such as IP addresses, please see
"Network Settings (Page 45)".
If an error message is shown on your display,
consult your phone system dealer or the
network administrator.
Use only the correct Panasonic handset.
Data Security
We recommend observing the security precautions
described in this section, in order to prevent the
following:
– loss, disclosure, falsification, or theft of user
information
– unauthorized use of the unit
– interference or suspension of use caused by an
unauthorized party
We cannot be responsible for damages resulting
from the misuse of this product.
User information is defined as the following:
– Phonebook names, phone numbers, and IP
addresses
– Forwarding destination numbers
– Numbers stored in One-touch Dialing buttons
– Passwords used to log in to the Web user interface
– Call logs
Preventing Data Loss
•
•
Keep a copy of all important data (such as the
phonebook list) in case the machine malfunctions
and data cannot be recovered.
There is a risk that data stored or saved on the unit
may be changed or deleted when, for instance, the
unit is being repaired. To protect important data
from unexpected damage, see Data Security
(Page 9).
Preventing Data Disclosure
•
•
•
•
•
Document Version 2012-06
Store backups in a secure location.
Do not store sensitive personal information in the
unit.
Personal information (such as the phonebook list
and call log) can be registered and/or saved on this
unit. To prevent data leakage or unexpected
damages, make a record of necessary user
information, etc., and initialize the unit to return it to
its factory settings in the following cases.
– When passing on or disposing of the unit
– When lending the unit
– When having the unit repaired
Make sure the unit is serviced by only a certified
technician.
When user information is sent from the unit to a PC
or other external device, the confidentiality of that
information becomes the responsibility of the
customer. Before disposing of the PC or other
Operating Instructions
9
Important Information
external device, ensure that data cannot be
retrieved from it by formatting the hard disk and/or
rendering it physically unusable.
Preventing Data Disclosure Over the
Network
•
•
•
To ensure the security of private conversations,
only connect the unit to a secure network.
To prevent unauthorized access, only connect the
unit to a network that is properly managed.
Make sure all personal computers that are
connected to the unit employ up-to-date security
measures.
Security Information
•
•
•
•
Security settings, such as passwords, cannot be
undone at Panasonic service centers. Take
measures to prevent passwords from being lost or
forgotten.
If a password is forgotten, initialize the unit and
configure the settings again. For details, consult
your administrator or dealer.
For best security, set passwords that cannot be
guessed easily, and change passwords
periodically.
If using SSL authentication, an NTP server must
also be specified. Furthermore, if SSL
authentication is performed without specifying an
NTP server, authentication will be unconditionally
validated without confirming the validity of the SSL
certificate.
Additional Information
Important Safety Instructions
When using this unit, basic safety precautions should
always be followed to reduce the risk of fire, electric
shock and injury to persons, including the following:
1. Do not use the unit near water, for example, near a
bathtub, washbowl, kitchen sink, or laundry tub, in
a wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote
risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the
vicinity of the leak.
SAVE THESE INSTRUCTIONS
FCC and Other Information
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate this
device.
FCC Declaration of Conformity
Trade Name: Panasonic
10
Operating Instructions
Document Version 2012-06
Important Information
Model Number: KX-UT123/KX-UT133/KX-UT136/
KX-UT248
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094 U.S.A.
Telephone No.: 1-800-211-PANA (7262)
shielding to RF energy commonly emitted by digital
devices.
This equipment complies with Part 68 of the FCC rules
and the requirements adopted by the ACTA. On the
bottom of the cabinet of this equipment is a label that
contains, among other information, a product identifier
in the format
US:ACJ.......
If requested, this number must be provided to the
telephone company.
For KX-UT248 only
This unit features a built-in Bluetooth module that
can be used to wirelessly connect a Bluetooth
headset to the unit.
If trouble is experienced with this equipment, for repair
or warranty information, please contact:
Panasonic Service and Technology Company-BTS
Center
415 Horizon Drive Bldg. 300 Ste. 350-B
Suwanee, GA 30024-3186
Connection to party line service is subject to state tariffs.
Contact the state public utility commission, public
service commission or corporation commission for
information.
If your home has specially wired alarm equipment
connected to the telephone line, ensure the installation
of this equipment does not disable your alarm
equipment. If you have questions about what will
disable alarm equipment, consult your telephone
company or a qualified installer.
For users in Canada only
• This Class B digital apparatus complies with
•
Canadian ICES-003.
This product meets the applicable Industry Canada
technical specifications.
Radio Frequency Exposure Requirements
This product complies with FCC/IC radiation exposure
limits set forth for an uncontrolled environment. To
comply with FCC/IC RF exposure requirements, it must
be installed and operated in accordance with provided
instructions. The unit requires minimum 20 cm (8 in)
spacing must be provided between antennas and all
person’s body (excluding extremities of hands, wrists
and feet) during wireless modes of operation. This
transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
Compliance with TIA-1083 standard
Compatible with
Hearing Aid T-Coil
Telephone handsets identified with
this logo have reduced noise and
interference when used with T-Coil
equipped hearing aids and cochlear
implants.
T
TIA-1083
WHEN PROGRAMMING EMERGENCY NUMBERS
AND (OR) MAKING TEST CALLS TO EMERGENCY
NUMBERS:
a. Remain on the line and briefly explain to the
dispatcher the reason for the call.
b. Perform such activities in the off-peak hours, such
as early morning or late evenings.
This equipment is hearing aid compatible.
When you hold the phone to your ear, noise might be
heard in your Hearing Aid. Some Hearing Aids are not
adequately shielded from external RF (radio frequency)
energy. If noise occurs, use the speakerphone option
(if applicable) when using this phone. Consult with your
audiologist or Hearing Aid manufacturer about the
availability of Hearing Aids which provide adequate
Document Version 2012-06
Operating Instructions
11
Before Operating the Telephone
Before Operating the Telephone
Accessory Information
Included Accessories
*1
Handset (1)
Handset Cord (1)
[Part No.]
Black model: PNLXQ1001Z
White model: PNLXQ1002Z
[Part No.]
Black model: PNJA1066Z
White model: PNJA1067Z
Stand (1)
*1
For KX-UT113/KX-UT123:
For KX-UT133/KX-UT136/KX-UT248:
[Part No.]
Black model: PNYLUT113BM
White model: PNYLUT113M
[Part No.]
Black model: PNYLUT133BM
White model: PNYLUT133M
For extra orders for the accessories, call toll-free: 1-800-332-5368. (For users in the United States only)
Note
•
The illustrations may differ from the appearance of the actual product.
Optional Accessories
*1
12
AC Adaptor*1
•
•
For users in the United States: KX-A239 (PQLV206)
For users in Canada: KX-A239X (PQLV206)
Wall Mount Kit
•
•
For KX-UT113/KX-UT123: KX-A432
For KX-UT133/KX-UT136/KX-UT248: KX-A433
To order an optional AC adaptor, please order using the "KX-A239" or "KX-A239X" model number (not "PQLV206").
Operating Instructions
Document Version 2012-06
Before Operating the Telephone
Location of Controls
Front View
For KX-UT113/KX-UT123:
A B
CDE
F
GHIJ
KL M N O P Q
For KX-UT133:
DE
A B
C
F
GHIJ
Document Version 2012-06
KL M
OPQ R N
Operating Instructions
13
Before Operating the Telephone
For KX-UT136:
DE
A B
C
F
GHIJ
KL M
OPQ R N
For KX-UT248:
AB
DE
G
H C JI
F
R S
Q S R K L MNOP
LCD (Liquid Crystal Display)
KX-UT113 is equipped with a 3-Line LCD.
KX-UT123/KX-UT133 is equipped with a 3-Line LCD and LCD backlight.
KX-UT136 is equipped with a 6-Line LCD and LCD backlight.
KX-UT248 is equipped with a 4.4-inch LCD and LCD backlight.
14
Operating Instructions
Document Version 2012-06
Before Operating the Telephone
Soft Buttons (S1 to S4)
S1 to S4 (located below the display) are used to select the item displayed on the bottom line of the display.
Message/Ringer Lamp*1
When you receive a call or Hold Recall, the lamp flashes green.
When someone has left you a message, the lamp stays on red.
*1
If KX-UT113/KX-UT123/KX-UT133/KX-UT136 is connected to a KX-NS1000 PBX, the Message/Ringer Lamp shows the current
status as follows:
–
–
–
Green flashing: You are receiving an intercom call, or you are receiving a Hold Recall or Transfer Recall from an extension.
Red flashing: You are receiving an outside call, or you are receiving a Hold Recall or Transfer Recall from an outside line.
Red on: You have a message.
Navigator Key
Used to adjust the volume or select desired items.
ENTER
Used to assign the selected item.
Handset Hook
Keeps the handset stable when the unit is mounted on a wall. For details, see "To Lock the Handset Hook
when the Unit is Wall Mounted (Page 72)".
FORWARD/DO NOT DISTURB
Used to set Call Forwarding or Do Not Disturb on your extension.
CONF (Conference)/CONFERENCE
Used to establish a local three-way conference.
REDIAL
Used to redial the last dialed number.
FLASH/RECALL
Used to disconnect the current call and make another call without hanging up.
MESSAGE
Used to access your voice mailbox.
HOLD
Used to put a call on hold.
When a call is on hold, the Hold lamp (KX-UT113/KX-UT123 only) flashes red.
MUTE/AUTO ANSWER
Used to receive an incoming call in hands-free mode or mute the microphone/handset during a
conversation.
MIC
Used for hands-free conversation.
TRANSFER
Used to transfer a call to another party.
SP-PHONE (Speakerphone)/HEADSET
Used for performing hands-free operations. When the SP-PHONE is used, the lamp on the SP-PHONE
(KX-UT133/KX-UT136/KX-UT248 only) or the lamp above the SP-PHONE (KX-UT113/KX-UT123 only)
turns red. When muted, the lamp flashes red.
CANCEL
Used to cancel the selected item.
Flexible Buttons/Flexible Button Lamps (KX-UT133/KX-UT136/KX-UT248 only)
Used to make or receive calls, or perform the feature that has been assigned to the button. The flexible
button lamp shows the status of each flexible button. For details, see "Flexible Buttons (KX-UT133/
KX-UT136/KX-UT248 only) (Page 35)".
Page Keys (KX-UT248 only)
Used to switch the page of flexible buttons displayed. There are three pages of eight flexible buttons. For
details, see "Display of Assigned Flexible Buttons (KX-UT248 only) (Page 20)".
Document Version 2012-06
Operating Instructions
15
Before Operating the Telephone
Left Side View
For KX-UT113/KX-UT123:
A
For KX-UT133/KX-UT136/KX-UT248:
B A
Headset Jack
EHS Jack (KX-UT133/KX-UT136/KX-UT248 only)
16
Operating Instructions
Document Version 2012-06
Before Operating the Telephone
Bottom View
For KX-UT113:
A B
C
A B D
C
For KX-UT123:
For KX-UT133/KX-UT136/KX-UT248:
A B
D
C
DC Jack
Document Version 2012-06
Operating Instructions
17
Before Operating the Telephone
LAN Port
Handset Jack
PC Port (KX-UT123/KX-UT133/KX-UT136/KX-UT248 only)
18
Operating Instructions
Document Version 2012-06
Before Operating the Telephone
Screens
This section explains the buttons and icons that appear on the display.
For KX-UT113/KX-UT123/KX-UT133:
Setting
Call Log
For KX-UT136:
Setting
Call Log
For KX-UT248:
BLF 1
DN 1
BLF 2
DN 2
BLF 3
0123456789
BLF 4
Headset
Setting
Call Log
Status Icons
Indicates the status of various features (Page 20).
Document Version 2012-06
Operating Instructions
19
Before Operating the Telephone
Soft Button Icons
Indicate the functions that will be accessed when the corresponding buttons are pressed. The icons
displayed vary according to the state of the unit. (For example, the icons displayed while on a call are
different from the icons displayed while storing an entry in the phonebook.)
Scroll Indicator
Indicates that [ ], [ ], [ ], or [ ] can be pressed to display the previous or next item.
Note
•
Although the scroll indicator is not shown in the screen sample of the KX-UT136/KX-UT248 above,
it does appear on some screens.
Display of Assigned Flexible Buttons (KX-UT248 only)
Indicates a page of flexible buttons (Page 35). The names assigned to the flexible buttons are displayed
on each page (Page 15).
Status Icons
Icon
Description
FWD/DND
Displayed when Call Forwarding or Do Not Disturb is enabled (Page 34).
AUTO ANS
Displayed when Auto Answer is enabled (Page 27).
Displayed when the ringer is turned off (Page 24).
ECO
Displayed when ECO mode is enabled (Page 41).
Displayed when registration to the SIP server has been lost. If this icon is
displayed, consult your administrator or dealer.
Displayed next to lines that have new messages when checking new messages
(Page 33).
For KX-UT248 only, displayed when a Bluetooth headset is registered and
connected (Page 74).
For KX-UT248 only, displayed when a Bluetooth headset is registered but not
connected (Page 74).
20
Operating Instructions
Document Version 2012-06
Before Operating the Telephone
Soft Buttons and Soft Button Icons
By pressing a soft button (S1 to S4), you can access the function displayed directly above it.
Setting
Call Log
S1
S2
S3
S4
In this manual, soft buttons are referred to by their corresponding icons.
In the example here, "Press Setting ", "Press Call Log ", or "Press
" would indicate pressing S1, S2, or S3,
respectively.
Icon
Description
Setting
Access the user setting menus (Page 38).
Call Log
Access the call log (Page 26).
Access the phonebook (Page 36).
Setup
Access the setup menus (Page 75).
Clear
Erase the number or character above the cursor (Page 25).
Search
Search for a phonebook entry (Page 25).
Menu
Edit a call log or phonebook entry (Page 26, Page 36).
Access the system features of the PBX (System Feature Access).
Note
•
OK
You can access the system features only if KX-UT113/KX-UT123/
KX-UT133/KX-UT136 is connected to a KX-NS1000 PBX. For details,
refer to the documentation of the KX-NS1000.
Confirm a transfer operation (Page 30).
Begin installation of a firmware update (Page 48).
Enter
Save or confirm the information shown on the display.
Note
•
Line
Document Version 2012-06
You can also use the physical ENTER button to perform the same
operation as this soft button.
For KX-UT113/KX-UT123 only, if multiple lines are available at your unit, select
the line to use to make a call (Page 25).
Operating Instructions
21
Before Operating the Telephone
Icon
Answer
Answer an incoming call (Page 23).
Close
Close the incoming call screen and continue pre-dialing (Page 25).
Reject
Reject an incoming call (Page 27).
Blind
Perform a blind transfer (Page 30).
Add
Add an entry, such as to the call rejection list or the phonebook (Page 28,
Page 36).
Erase
Erase the information shown on the display (Page 28, Page 37).
Save
Save the information shown on the display (Page 28, Page 36).
Call
Make a call (Page 25).
Edit
Edit the information shown on the display (Page 26, Page 28, Page 36).
Prefer
Assign the preferred number to dial among multiple registered phone numbers in
the same phonebook entry, when making a call using the phonebook
(Page 36).
Number
Display the telephone number when searching an entry in the phonebook
(Page 25).
Update
Update the firmware (Page 48).
A/a
1/A/?
22
Description
Operating Instructions
Switch between uppercase and lowercase entry when entering characters
(Page 51).
Select the desired character entry mode when entering characters (Page 52).
Document Version 2012-06
Before Operating the Telephone
Basic Operations
•
Press [SP-PHONE/HEADSET] when using a
headset or when you are in hands-free mode.
This section explains the basics of using the unit.
Hands-free Mode
Note
•
If KX-UT113/KX-UT123/KX-UT133/KX-UT136
is connected to a Panasonic KX-NS1000 PBX,
refer to the documentation of the KX-NS1000
for information about the operation of the unit.
In hands-free mode, you can talk and hear the other
party in a conversation without using the handset. This
mode is useful for performing other tasks during a
conversation, such as writing.
Enabling hands-free mode
Confirming Your Extension
Number
In stand-by mode (i.e., when you do not have any active
calls), you can view the extension number and name
registered to the unit.
Going off- and on-hook
There are several ways to go off-hook and on-hook:
• Using the handset
• Using the [SP-PHONE/HEADSET] button
• Using the soft buttons
• For KX-UT133/KX-UT136/KX-UT248, using a DN
button (flexible button)
Going off-hook
In this manual, when you see the phrase "go off-hook",
you can do any of the following:
• Lift the handset off of its cradle.
• Press [SP-PHONE/HEADSET] while the handset is
on its cradle. This enables hands-free mode.
• Press [SP-PHONE/HEADSET] when using a
headset.
• For KX-UT133/KX-UT136/KX-UT248, press a DN
button (flexible button).
Note
•
•
Certain soft buttons, such as Answer , function
like the [SP-PHONE] button.
For details about DN buttons, see "Flexible
Buttons (KX-UT133/KX-UT136/KX-UT248
only) (Page 35)".
Going on-hook
In this manual, when you see the phrase "go on-hook",
you can do any of the following:
• Replace the handset on its cradle.
Document Version 2012-06
You can enable hands-free mode in one of the following
ways:
• In stand-by mode, press [SP-PHONE].
• During a conversation while using the handset,
press [SP-PHONE]. You can then return the
handset to its cradle.
• When receiving an incoming call, press Answer .
• For KX-UT133/KX-UT136/KX-UT248, in stand-by
mode, press an idle DN button (flexible button).
• For KX-UT133/KX-UT136/KX-UT248, when
receiving a call or when a call is on hold, press the
flashing green DN button (flexible button) that
corresponds to the call.
Canceling hands-free mode
You can cancel hands-free operation simply by lifting
the handset off its cradle.
Note
•
For details about DN buttons, see "Flexible
Buttons (KX-UT133/KX-UT136/KX-UT248
only) (Page 35) ".
Off-hook monitor
During a two-party conversation with the corded
handset, you can allow other people to listen to the
conversation through the speaker while you continue
the conversation using the handset.
• Press [SP-PHONE], but do not return the handset
to its cradle.
• Press [SP-PHONE] again to cancel off-hook
monitor.
Note
•
•
When off-hook monitor is active, replacing the
handset to its cradle enables hands-free mode.
During a conference call, pressing
[SP-PHONE] simply enables hands-free mode.
The handset will be disabled.
Operating Instructions
23
Before Operating the Telephone
Adjusting the Volume
You can adjust the ringer, handset, headset, and
speaker volume using [ ] and [ ] on the Navigator key.
Adjusting the ringer volume
When receiving a call, press [ ] or [ ].
You can also adjust the ringer volume in the settings.
For details, see "Ringer (Page 41)".
Note
•
When the ringer volume is turned all the way
down, "Off" is displayed. Also,
is
displayed when the unit is in stand-by mode.
Adjusting the handset/headset/
speaker volume
Press [ ] or [ ] during a conversation when using the
handset, headset, or when you are in hands-free mode.
24
Operating Instructions
Document Version 2012-06
Feature Operations
Feature Operations
•
Note
•
If KX-UT113/KX-UT123/KX-UT133/KX-UT136
is connected to a Panasonic KX-NS1000 PBX,
refer to the documentation of the KX-NS1000
for information about the operation of the unit.
However, please refer to this documentation for
details about the following features:
– Phonebook (Page 25, 36)
– Call Log (Page 26)
Making Calls
This section explains the basic methods for making a
call.
Making a Call
1. In stand-by mode, go off-hook.
2. Enter the number you want to call.
3. Press [ENTER], or wait a few seconds for the
number to be dialed.
4. To end the call, go on-hook.
•
Making a Call from the
Phonebook List
Scrolling through all entries
1.
2.
3.
4.
Press
.
Press [ ] or [ ] to select an entry.
Go off-hook.
To end the call, go on-hook.
Note
•
Note
•
•
For KX-UT113/KX-UT123, if more than one line
is available at your unit, you can press Line
before going off-hook and then select the line
you want to use.
For KX-UT133/KX-UT136/KX-UT248, if more
than one line is available at your unit, you can
press an idle DN button (flexible button)
assigned to the line you want to use before
entering the number. For details about DN
buttons, see "Flexible Buttons (KX-UT133/
KX-UT136/KX-UT248 only) (Page 35)".
Pre-dialing
In stand-by mode, you can start dialing (max. 32 digits)
while still on-hook.
• To delete a number you entered, press Clear .
•
•
To clear the entire number, press and hold Clear .
To connect the call, go off-hook or press [ENTER].
Note
•
For KX-UT133/KX-UT136/KX-UT248, you can
also press an idle DN button (flexible button) to
connect the call. For details about DN buttons,
Document Version 2012-06
see "Flexible Buttons (KX-UT133/KX-UT136/
KX-UT248 only) (Page 35)".
For KX-UT113/KX-UT123, when pre-dialing
you can press Call instead of going off-hook.
If more than one line is available at your unit,
select the line to use, and then press [ENTER].
If you receive an incoming call during
pre-dialing, the display changes to the incoming
call screen. For KX-UT133/KX-UT136/
KX-UT248, you can close the incoming call
screen by pressing Close , and continue
pre-dialing.
•
•
For KX-UT133/KX-UT136/KX-UT248, you can
also press an idle DN button (flexible button) in
step 3 to connect the call. For details about DN
buttons, see "Flexible Buttons (KX-UT133/
KX-UT136/KX-UT248 only) (Page 35)".
For KX-UT113/KX-UT123, you can press
Call instead of going off-hook. If more than
one line is available at your unit, select the line
to use, and then press [ENTER].
In step 2, if multiple phone numbers are stored
for the entry, you can press Number and then
select the phone number to call.
Searching by name
.
1. Press
2. Press Search .
3. Enter the name (max. 12 characters) you want to
search for.
4. Press [ENTER].
The entry that matches your search appears.
5. Go off-hook.
6. To end the call, go on-hook.
Note
•
For KX-UT113/KX-UT123, you can press
Call instead of going off-hook. If more than
Operating Instructions
25
Feature Operations
•
•
•
one line is available at your unit, select the line
to use, and then press [ENTER].
For details about entering characters, see
"Entering Characters (Page 51)".
In step 4, if multiple phone numbers are stored
for the entry, you can press Number and then
select the phone number to call.
If you do not press any buttons for 1 minute, the
unit will return to stand-by mode.
Dialing by Using Call Logs
The last 30 incoming calls and outgoing calls are stored
in their respective logs, in order of newest to oldest call.
Missed incoming calls appear in the missed call log in
addition to the incoming call log.
You can make calls to the numbers listed in the call logs.
1. Press Call Log .
2. Press [ ] or [ ] to select the call log type, and then
press [ENTER].
3. Press [ ] or [ ] to select the desired entry.
4. Go off-hook.
5. To end the call, go on-hook.
4. Do one of the following, depending on your unit:
For KX-UT113/KX-UT123 users
• Press Menu , select "Edit", and then press
[ENTER].
For KX-UT133/KX-UT136/KX-UT248 users
• Press Edit .
5. Edit the number, and then go off-hook or press
Call .
6. To end the call, go on-hook.
Redialing the Last Number You
Dialed (Redial, Last Number)
You can redial the last phone number that you dialed.
1. Press [REDIAL].
2. To end the call, go on-hook.
Note
•
Note
•
•
•
For KX-UT133/KX-UT136/KX-UT248, you can
also press an idle DN button (flexible button) in
step 4 to connect the call. For details about
flexible buttons, see "Flexible Buttons
(KX-UT133/KX-UT136/KX-UT248 only)
(Page 35)".
For KX-UT113/KX-UT123, you can press
Call instead of going off-hook. If more than
one line is available at your unit, select the line
to use, and then press [ENTER].
You can add a call log entry to the phonebook.
See "Adding a Phonebook Entry from the
Incoming or Missed Call Log (Page 36)".
Editing a phone number before
dialing from the incoming or missed
call log
You can edit a phone number in the incoming or missed
call log before using it to dial.
1. Press Call Log .
2. Press [ ] or [ ] to select "Incoming Call Log"
or "Missed Call", and then press [ENTER].
3. Press [ ] or [ ] to select the desired entry.
26
Operating Instructions
•
For KX-UT133/KX-UT136/KX-UT248, to select
a line to use to redial, press the appropriate DN
button (flexible button) before you press
[REDIAL]. For details about DN buttons, see
"Flexible Buttons (KX-UT133/KX-UT136/
KX-UT248 only) (Page 35)".
The unit may be configured to display the
outgoing call log instead of immediately
redialing. You can select an entry from the call
log to make a call (Page 26). For details, consult
your administrator or dealer.
One-touch Dialing (KX-UT133/
KX-UT136/KX-UT248 only)
You can make a call with a One-touch operation if a
One-touch Dialing button has been created for the
desired party. One-touch Dialing buttons can also be
configured to access features of your phone system, if
available.
1. Go off-hook, and then press the One-touch Dialing
button (flexible button).
2. To end the call, go on-hook.
Note
•
•
A BLF (Busy Lamp Field) button (flexible button)
can also be used to call an extension simply by
pressing the button. For details, consult your
administrator or dealer.
For details about flexible buttons such as
One-touch Dialing buttons and BLF buttons,
Document Version 2012-06
Feature Operations
see "Flexible Buttons (KX-UT133/KX-UT136/
KX-UT248 only) (Page 35)".
Receiving Calls
This section explains the basic methods for receiving a
call.
Receiving a Call
1. Go off-hook.
2. To end the call, go on-hook.
Auto answer
You can have the unit automatically answer an
incoming call. The call is connected after a programmed
number of rings.
• To enable Auto Answer:
In stand-by mode, press [AUTO ANSWER] until
"Auto Answer On" appears.
• To disable Auto Answer:
In stand-by mode, press [AUTO ANSWER] until
"Auto Answer Off" appears.
Note
•
When Auto Answer is enabled, AUTO ANS
appears on the display in stand-by mode.
Rejecting Calls
You can reject an incoming call at your unit or set the
unit to reject certain calls.
Rejecting a call while receiving
1. When receiving an incoming call, press
Reject
.
Rejecting anonymous calls
You can set the unit to reject calls when the unit
receives a call without phone number.
To reject anonymous calls, the Block Anonymous Call
setting must be enabled through Web user interface
programming (Page 59). For details, consult your
administrator or dealer.
Note
•
•
Document Version 2012-06
Rejected phone numbers will not be stored in
the incoming or missed call log.
Depending on the line an incoming call is
arriving on, the call may not be rejected.
Operating Instructions
27
Feature Operations
Rejecting specific calls
You can set the unit to reject specific phone numbers.
Note
•
Rejected phone numbers will not be stored in
the incoming or missed call log.
Adding a phone number
You can store a maximum of 30 phone numbers you
want to reject in the rejection list of the unit.
1. In stand-by mode, press Setting .
2. Press [ ] or [ ] to select "Call Block", and then
press [ENTER].
3. Press Add .
4. Enter the telephone number (max. 32 digits), and
then press [ENTER].
Note
•
If you do not press any buttons for 1 minute, the
unit will return to stand-by mode.
Deleting a stored phone number
1. In stand-by mode, press Setting .
2. Press [ ] or [ ] to select "Call Block", and then
press [ENTER].
3. Press [ ] or [ ] to select the phone number you
want to delete, and then press Erase .
4. Press [ ] or [ ] to select "Yes", and then press
[ENTER].
Note
•
If you do not press any buttons for 1 minute, the
unit will return to stand-by mode.
Note
•
To register additional telephone numbers,
repeat the procedure from step 3.
Adding a phone number from the incoming or
missed call log
You can add a phone number by referring to the
incoming or missed call log.
1. In stand-by mode, press Call Log .
2. Press [ ] or [ ] to select "Incoming Call Log"
or "Missed Call", and then press [ENTER].
3. Press [ ] or [ ] to select the entry with the phone
number you want to reject.
4. Press Save .
5. Press [ ] or [ ] to select "Call Block", and then
press [ENTER].
6. Press [ ] or [ ] to select "Yes", and then press
[ENTER].
Note
•
If you do not press any buttons for 1 minute, the
unit will return to stand-by mode.
Editing a stored phone number
1. In stand-by mode, press Setting .
2. Press [ ] or [ ] to select "Call Block", and then
press [ENTER].
3. Press [ ] or [ ] to select the phone number you
want to edit, and then press Edit .
4. Edit the phone number as necessary, and then
press [ENTER].
28
Operating Instructions
Document Version 2012-06
Feature Operations
Holding a Call
You can put a call on hold by holding the call at your
extension.
To hold the current call
1. Press [HOLD], and then go on-hook.
Note
•
For KX-UT133/KX-UT136/KX-UT248, if
Automatic Call Hold is enabled on your unit,
the call will also be put on hold if you press
a DN button (flexible button) other than the
one for the current call. For details, consult
your administrator or dealer.
To retrieve a call on hold at your extension
1. Go off-hook.
2. Do one of the following, depending on your unit:
For KX-UT113/KX-UT123 users
• Press [HOLD].
For KX-UT133/KX-UT136/KX-UT248 users
• Press the green flashing DN button (flexible
button).
Receiving a Second Call
(Answering Call Waiting)
During a conversation, if a second call arrives, you will
hear a call waiting tone.
You can answer the second call by disconnecting or
holding the current call.
To disconnect the current call and then talk to
the new party
1. Go on-hook while hearing the call waiting tone.
2. Go off-hook.
To hold the current call and then talk to the new
party
For KX-UT113/KX-UT123 users
1. Press [HOLD] while hearing the call waiting tone.
For KX-UT133/KX-UT136/KX-UT248 users
1. Press [HOLD] while hearing the call waiting tone.
2. Press the green flashing DN button (flexible button).
Note
•
Note
•
•
If a call is not retrieved within a specified time,
you will hear an alarm as a reminder (Hold
Recall).
For details about DN buttons, see "Flexible
Buttons (KX-UT133/KX-UT136/KX-UT248
only) (Page 35)".
Document Version 2012-06
•
For KX-UT133/KX-UT136/KX-UT248, if
Automatic Call Hold is enabled on your unit, you
do not need to press [HOLD] in step 1. The call
is automatically put on hold when you press the
DN button. For details, consult your
administrator or dealer.
For details about DN buttons, see "Flexible
Buttons (KX-UT133/KX-UT136/KX-UT248
only) (Page 35)".
Operating Instructions
29
Feature Operations
Talking to Two Parties
Transferring a Call (Call
Alternately (Call Splitting) Transfer)
When you are talking to one party and have another
party on hold, you can switch the call on hold and the
current call.
1. Press [HOLD] during a conversation.
2. Call the second party.
3. Do one of the following, depending on your unit:
For KX-UT113/KX-UT123 users
• Press [HOLD].
For KX-UT133/KX-UT136/KX-UT248 users
• Press [HOLD], and then press the green
flashing DN button (flexible button) that
corresponds to the other party on hold.
You can transfer a call to another destination (extension
or outside party).
To transfer
1. Press [TRANSFER] during a conversation.
2. Call the party you want to transfer the call to.
3. Wait until the other party answers to announce the
transfer.
4. Press
•
For KX-UT133/KX-UT136/KX-UT248, if
Automatic Call Hold is enabled on your unit, you
do not need to press [HOLD] in step 3. The call
is automatically put on hold when you press the
DN button. For details, consult your
administrator or dealer.
For details about DN buttons, see "Flexible
Buttons (KX-UT133/KX-UT136/KX-UT248
only) (Page 35)".
.
Note
•
Note
•
OK
•
•
If On-hook Transfer is enabled on your unit, you
can simply go on-hook in step 4 instead of
pressing OK . For details, consult your
administrator or dealer.
If unscreened transfers are supported on your
phone system, step 3 can be omitted. For
details, consult your administrator or dealer.
For KX-UT113/KX-UT123, if a call is on hold
(Page 29), the transfer operation cannot be
performed.
To do a blind transfer
1. Press Blind during a conversation.
2. Call the party you want to transfer the call to.
3. Go on-hook.
Note
•
For KX-UT113/KX-UT123, if a call is on hold
(Page 29), the transfer operation cannot be
performed.
To Transfer with One Touch
(One-touch Transfer)
(KX-UT133/KX-UT136/
KX-UT248 only)
1. Press the BLF button (flexible button) during a
conversation.
2. Wait until the other party answers to announce the
transfer.
3. Press OK .
Note
•
30
Operating Instructions
If On-hook Transfer is enabled on your unit, you
can simply go on-hook in step 3 instead of
Document Version 2012-06
Feature Operations
•
•
pressing OK . For details, consult your
administrator or dealer.
If unscreened transfers are supported on your
phone system, step 2 can be omitted. For
details, consult your administrator or dealer.
For details about flexible buttons, see "Flexible
Buttons (KX-UT133/KX-UT136/KX-UT248
only) (Page 35)".
Mute
You can mute your voice during a conversation. While
the mute feature is turned on, you will be able to hear
the other party, but the other party will not be able to
hear you.
The built-in microphone, handset, and headset are all
muted when the mute feature is turned on.
To mute/unmute
1. Press [MUTE].
Document Version 2012-06
Operating Instructions
31
Feature Operations
Conference Call (Local
Three-way Conference)
During a conversation, you can add an additional party
to your call and establish a conference call.
Notice
•
Your phone system may support advanced
conference features, such as conference calls
with four or more parties. In this case, the
procedures for handling a conference call may
be different from those explained in this section.
For details about your phone system, consult
your administrator or dealer.
Making a Conference Call
1. Press [CONFERENCE]/[CONF] to put the current
call on hold.
2. Call the party you want to add to the conversation.
3. After the called party answers, press
[CONFERENCE]/[CONF] to begin the conference
call.
Removing a Party from the
Conference
For KX-UT133/KX-UT136/KX-UT248 users
1. During a conference call, press [HOLD].
• The other parties are put on hold.
2. Press the DN button (flexible button) that
corresponds to the party you want to disconnect.
• A conversation is established with the party you
want to disconnect.
3. Go on-hook.
• The party is disconnected.
4. Press the DN button (flexible button) that
corresponds to the remaining party.
• You can continue the conversation with the
remaining party.
Note
•
•
To reestablish the conference without removing
either party, press [CONFERENCE]/[CONF]
after step 2.
For details about DN buttons, see "Flexible
Buttons (KX-UT133/KX-UT136/KX-UT248
only) (Page 35)".
Ending a Conference Call
1. Go on-hook during a conference.
During a conference, you can remove other parties from
the conference. However, this operation is available
only during conference calls you initiate.
For KX-UT113/KX-UT123 users
1. During a conference call, press [HOLD].
• The second party is put on hold, but you can
continue talking to the first party.
2. Go on-hook.
• The first party is disconnected.
3. Press [HOLD].
• You can continue the conversation with the
second party.
Note
•
•
32
To disconnect the second party instead of the
first party, press [HOLD] 2 times in step 1.
To reestablish the conference without removing
either party, press [CONFERENCE] after step
1.
Operating Instructions
Document Version 2012-06
Feature Operations
Checking Messages
Checking New Messages
When you receive a voice message, "Message"
appears on the display, and the Message/Ringer lamp
turns red.
You can check your new messages by accessing your
mailbox.
1. Press [MESSAGE].
2. If the unit has multiple lines, press [ ] or [ ] to select
the line on which
is displayed, and then go
off-hook.
Checking Missed Calls
When there are new missed calls, "Missed Call:
XXX" appears on the display. ("XXX" indicates the
number of missed calls.)
1. Press Call Log .
2. Press [ ] or [ ] to select "Incoming Call Log"
or "Missed Call", and then press [ENTER].
3. Press [ ] or [ ] to select the missed call.
Note
•
•
•
Document Version 2012-06
In the incoming call log, "Not Answered" is
displayed on missed calls. For KX-UT113/
KX-UT123/KX-UT133, you must press [ ] to
see this.
For details about making calls from the call log,
see "Dialing by Using Call Logs (Page 26)".
A check mark is displayed next to answered
calls and missed calls that you have already
checked.
Operating Instructions
33
Feature Operations
Call Forwarding/Do Not
Disturb
You can have incoming calls automatically forwarded
to another destination. You can also have incoming
calls rejected (Do Not Disturb).
Logging in to or Logging
out of a Group
(KX-UT133/KX-UT136/
KX-UT248 only)
Note
•
When Call Forwarding or Do Not Disturb is
enabled, FWD/DND appears on the display in
stand-by mode.
To access the FWD/DND settings
1. In stand-by mode, press
2.
3.
4.
5.
Setting
or [FORWARD/DO
NOT DISTURB].
• If you press [FORWARD/DO NOT DISTURB],
continue to step 3.
Press [ ] or [ ] to select "FWD/DND Setting", and
then press [ENTER].
If the unit has multiple lines, press [ ] or [ ] to select
the desired line, and then press [ENTER].
Press [ ] or [ ] to select the type of FWD or DND
setting to apply, and then press [ENTER].
Configure the settings as necessary (Page 43).
Logging in to or Logging out of
an ACD (Automatic Call
Distribution) Group
If the SIP server supports ACD and you are assigned
to an ACD group, you can log in to or log out of the
group.
1. In stand-by mode, press the flexible button
assigned as the ACD Log-in/Log-out button.
Note
•
The flexible button's light indicates the status as
follows:
Off: logged in to the ACD group
Red On: logged out of the ACD group
To set/cancel Not Ready mode
or to leave Wrap Up mode
Press the flexible button assigned as the Wrap Up
button.
The status will change as follows:
Ready ® Not Ready
Not Ready ® Ready
Wrap Up ® Not Ready
Note
•
34
Operating Instructions
The Wrap Up button's light shows the current
status as follows:
Off: Ready mode for incoming calls
Red on: Not Ready mode for incoming calls
Flashing red: Wrap Up mode
Document Version 2012-06
Feature Operations
Flexible Buttons
(KX-UT133/KX-UT136/
KX-UT248 only)
The flexible buttons on the unit can be customized to be
used to make or receive calls or as feature buttons.
These buttons are configured by your administrator or
dealer.
The following types of flexible buttons are available:
DN (Directory Number)
Seizes the line assigned to the DN button. When a
call arrives at the DN button, pressing the button
answers the call.
Lamp Indication
• Off: Idle
• Green on: You are on a call using the DN
button.
• Flashing green rapidly: A call is being
received.
• Flashing green slowly: A call is on hold.
• Red on: A shared line is in use or on hold
(private) at another unit.
• Flashing red slowly: A shared line is on hold
(normal) at another unit.
•
Note
•
BLF (Busy Lamp Field) is an optional
feature and may not be supported on your
phone system.
ACD
Logs in to or logs out of a group when ACD
(Automatic Call Distribution) is enabled (Page 34).
Lamp Indication
• Off: Logged in
• Red on: Logged out
Note
Note
•
BLF (Busy Lamp Field)
Calls the extension assigned to the button. During
a conversation, a BLF button can be used to
transfer calls to the assigned extension (Page 30).
A BLF button’s lamp also shows the current status
of the assigned extension.
Lamp Indication
• Off: The assigned extension is idle.
• Red on: The assigned extension is using the
line.
• Flashing red rapidly: The assigned extension
is receiving an incoming call.
If enabled through Web user interface
programming, pressing the button answers the
call (Directed Call Pickup).
A ringtone can be assigned to each DN
button through Web user interface
programming. When a call arrives at a DN
button, the ringtone assigned to that button
plays. For details, consult your
administrator or dealer.
However, if you select a ringtone through
the unit's settings (Page 41), that ringtone
will play instead of those assigned to DN
buttons.
A shared line is a line that can be used by
multiple units. This is an optional feature
and may not be supported on your phone
system.
One-Touch
Calls the party or accesses a feature assigned to
the button. See "One-touch Dialing (KX-UT133/
KX-UT136/KX-UT248 only) (Page 26)".
•
ACD is an optional feature and may not be
supported on your phone system.
Wrap Up
The Wrap Up button alternates the setting of Wrap
Up mode, Not Ready mode or Ready mode for
incoming calls.
In Wrap Up mode/Not Ready mode for incoming
calls, incoming calls will not be received through the
ACD (Automatic Call Distribution) group.
Lamp Indication
• Off: Ready mode for incoming calls
• Red on: Not Ready mode for incoming calls
• Flashing red: Wrap Up mode
Note
•
Wrap Up is an optional feature and may not
be supported on your phone system.
Headset
Enables or disables talking using the headset.
Lamp Indication
• Off: Headset off
• Red on: Headset on
Document Version 2012-06
Operating Instructions
35
Customizing the Telephone
Customizing the Telephone
Phonebook List
Adding a New Phonebook Entry
You can add a maximum of 500 (for KX-UT123/
KX-UT133/KX-UT136/KX-UT248) or 100 (for
KX-UT113) phonebook entries to the unit.
To make a call from the phonebook, see "Making a Call
from the Phonebook List (Page 25)".
1. Press
.
3. Press [ ] or [ ] to select the desired call log entry,
4.
5.
6.
7.
2. Press Add .
3. Enter a name (max. 24 characters), and then press
4.
5.
6.
7.
[ENTER].
Press [ ] or [ ] to select the phone number type
(A to E) or "Ringtone X", and then press
[ENTER].
Do one of the following, depending on your
selection in the previous step:
If you selected a phone number type
• Enter the phone number (max. 32 digits), and
then press [ENTER].
If you selected "Ringtone X"
• Select a ringtone to play when you receive a call
from this party, and then press [ENTER].
To add another phone number to the entry, repeat
the procedure from step 4.
Press Save .
8.
9.
and then press Save .
Select "Phonebook", and then press [ENTER].
Enter a name (max. 24 characters), and then press
[ENTER].
Press [ ] or [ ] to select the phone number type
(A to E) or "Ringtone X", and then press
[ENTER].
Do one of the following, depending on your
selection in the previous step:
If you selected a phone number type
• Enter the phone number (max. 32 digits), and
then press [ENTER].
If you selected "Ringtone X"
• Select a ringtone to play when you receive a call
from this party, and then press [ENTER].
To add another phone number to the entry, repeat
the procedure from step 6.
Press Save .
Note
•
•
•
If a name is stored in the call log, it is
automatically entered in step 5.
If you store multiple phone numbers in the entry,
you can assign the preferred number to use
when you call this party. In step 6, select the
desired number, and then press Prefer .
If you do not press any buttons for 1 minute, the
unit will return to stand-by mode.
Note
•
•
If you store multiple phone numbers in the entry,
you can assign the preferred number to use
when you call this party. In step 4, select the
desired number, and then press Prefer .
If you do not press any buttons for 1 minute, the
unit will return to stand-by mode.
Adding a Phonebook Entry from
the Incoming or Missed Call Log
You can add new phonebook entries from the incoming
or missed call log.
1. Press Call Log .
2. Press [ ] or [ ] to select "Incoming Call Log"
or "Missed Call", and then press [ENTER].
36
Operating Instructions
Editing a Phonebook Entry
You can edit the information stored in phonebook
entries.
1. Press
.
2. Press [ ] or [ ] to display the desired entry, or press
Search and search for the desired entry (Page 37).
3. Do one of the following, depending on your unit:
For KX-UT113/KX-UT123 users
• Press Menu , select "Edit", and then press
[ENTER].
For KX-UT133/KX-UT136/KX-UT248 users
• Press Edit .
4. Press [ ] or [ ] to select the item you want to edit,
and then press [ENTER].
Document Version 2012-06
Customizing the Telephone
5. Edit the item as necessary, and then press
[ENTER].
6. Press Save .
Note
•
•
If you store multiple phone numbers in the entry,
you can assign the preferred number to use
when you call this party. In step 4, select the
desired number, and then press Prefer .
If you do not press any buttons for 1 minute, the
unit will return to stand-by mode.
Searching for a Phonebook
Entry
You can search the phonebook for the desired entry.
1. Press
.
2. Press Search .
3. Enter the name you want to search for, and then
Also, phonebook entries exported from one unit can be
imported into another, which makes it easy to share
phonebook entries.
To export/import entries, consult your administrator or
dealer.
Notice
•
If you export the phonebook, delete some
entries on your computer, and then import the
phonebook to the unit, the entries deleted on
your computer will not be deleted from the
unit’s phonebook. To erase unnecessary
entries, use the unit’s interface and not the Web
user interface.
Note
•
•
Phone calls cannot be made or received while
phonebook entries are being imported or
exported.
If KX-UT113/KX-UT123/KX-UT133/KX-UT136
is connected to a KX-NS1000 PBX, you cannot
export or import phonebook entries.
press [ENTER].
Deleting a Phonebook Entry
You can delete phonebook entries.
1. Press
.
2. Press [ ] or [ ] to display the desired entry, or press
Search and search for the desired entry (Page 37).
3. Do one of the following, depending on your unit:
For KX-UT113/KX-UT123 users
• Press Menu , select "Erase", and then press
[ENTER].
For KX-UT133/KX-UT136/KX-UT248 users
• Press Erase .
4. Press [ ] or [ ] to select "Yes", and then press
[ENTER].
Export/Import Phonebook
Entries
You can export the phonebook entries through the Web
user interface to your computer as a tab separated
value file. This makes it possible to add and edit
phonebook entries using a spreadsheet application or
text editor on your computer. After editing, the file
should be imported into the unit.
Document Version 2012-06
Operating Instructions
37
Customizing the Telephone
User Settings
You can configure various settings to customize the behavior of the unit.
This section explains how to configure the settings using the unit.
Accessing the Settings
1. In stand-by mode, press Setting .
2. Press [ ] or [ ] to select the desired setting category, and then press [ENTER].
3. Configure the settings as necessary.
38
Operating Instructions
Document Version 2012-06
Customizing the Telephone
Available Settings
Ringer
Ringer Volume
Page 41
Ringtone
Page 41
ECO Mode
Page 41
LCD Contrast
Page 42
Backlight
Page 42
Display Lock
Page 42
Key Click Tone
Page 42
FWD/DND Setting*1
Do Not Disturb
Page 43
FWD All
Page 43
FWD Busy
Page 43
FWD No Ans
Page 43
Language
Page 44
Date and Time
Page 44
Information Display
Page 45
Network Settings
Network
DHCP
Page 45
DNS
Page 46
DNS1*2
Page 46
DNS2*2
Page 46
STATIC
LLDP-MED*4
VLAN
Speed/Duplex
Embedded web*4
Page 46
IP Address
Page 46
Subnet mask
Page 46
Default Gateway
Page 46
DNS1
Page 46
DNS2
Page 46
On/Off
Page 46
Timer
Page 46
PC port
Page 46
Enable VLAN
Page 47
IP Phone
Page 47
PC*3
Page 47
LAN port
Page 47
PC port*3
Page 47
Page 47
Network Test
Page 48
Document Version 2012-06
Operating Instructions
39
Customizing the Telephone
Restart
Page 48
Firmware version
Page 48
Call Block
Page 49
Bluetooth Headset*5
*1
*2
*3
*4
*5
40
Add new device
Enter PIN
Page 50
Disconnect
Page 50
Connect
Page 50
Deregistration
Page 50
For details about the FWD/DND settings when KX-UT113/KX-UT123/KX-UT133/KX-UT136 is connected to a KX-NS1000 PBX, refer
to the documentation of the KX-NS1000.
This setting is available only if "DNS" is set to "Manual".
This setting is available only on KX-UT123/KX-UT133/KX-UT136/KX-UT248.
This setting is not available if KX-UT113/KX-UT123/KX-UT133/KX-UT136 is connected to a KX-NS1000 PBX.
This setting is available only on KX-UT248.
Operating Instructions
Document Version 2012-06
Customizing the Telephone
Settings Details
Ringer
Setting
Description
Value Range
Default
Ringer Volume
Adjust the ringer volume.
Level 0 to 6
Level 3
Ringtone
Select a ringtone to play when you
receive a call. If multiple lines are
configured on your unit, you must first
select which line to use the ringtone
for. You can assign a different
ringtone to each line.
If you select
"Automatic" (KX-UT133/
KX-UT136/KX-UT248 only), the
ringtone assigned through Web user
interface programming (Page 59)
will be used.
Each ringtone will play as you
highlight it.
<KX-UT113/
KX-UT123>
Ringtone 1–
Ringtone 32
<KX-UT113/
KX-UT123>
Ringtone 1
<KX-UT133/
KX-UT136/
KX-UT248>
Automatic, Ringtone
1–Ringtone 32
<KX-UT133/
KX-UT136/
KX-UT248>
Automatic
Note
•
•
•
•
•
The preset melodies in this product are used with permission of © 2009 Copyrights Vision Inc.
Ringtone 20 to Ringtone 24 are the same as Ringtone 1.
Even if you have turned the volume off (level 0), each ringtone will still play when you highlight it.
However, nothing plays when you highlight "Automatic".
Ringtones can also be assigned to individual entries in the phonebook list (Page 36).
For KX-UT133/KX-UT136/KX-UT248, ringtones may also be assigned to individual DN buttons (flexible
buttons, Page 35) through Web user interface programming (Page 59). However, ringtones specified
here override the DN button settings. For details, consult your administrator or dealer.
ECO Mode
Setting
ECO Mode
Description
Enabling this mode reduces the
amount of electricity consumed by
the unit.
Value Range
Default
On, Off
Off
Note
•
When ECO mode is enabled, the Speed/Duplex setting (Page 47) changes as follows:
– Speed/Duplex: "10M-Full"
– PC port cannot be used.
•
•
When the ECO mode setting is changed, the unit will restart.
When ECO mode is enabled, ECO is displayed while the unit is in stand-by mode.
Document Version 2012-06
Operating Instructions
41
Customizing the Telephone
LCD Contrast
Setting
LCD Contrast
Description
Change the contrast of the display.
Value Range
Default
Level 1 to 6
Level 3
Backlight (KX-UT123/KX-UT133/KX-UT136/KX-UT248 only)
Setting
Backlight
Description
Value Range
Default
Change the settings for the backlight.
Always On
Automatic
Always Off
Automatic
<KX-UT123/
KX-UT133/
KX-UT136>
Level 1 to 3
<KX-UT123/
KX-UT133/
KX-UT136>
Level 3
<KX-UT248>
Level 1 to 6
<KX-UT248>
Level 6
If you select "Always On" or
"Automatic", press [ ] or [ ] to
adjust the brightness.
Note
•
When "Automatic" is selected, the backlight turns off when the phone returns to an idle state.
Display Lock
Setting
Display Lock
Description
Lock access to your call log and
phonebook list by entering your
extension PIN (Personal
Identification Number).
Value Range
Default
On, Off
Off
Note
•
The extension PIN can be configured through Web user interface programming. For details, consult
your administrator or dealer.
Key Click Tone
Setting
Key Click Tone
42
Operating Instructions
Description
Value Range
Default
Select whether a tone is heard in
response to key presses. If you
select "Automatic", the setting
assigned through Web user interface
programming (Page 59) will be
used.
Automatic, On, Off
Automatic
Document Version 2012-06
Customizing the Telephone
FWD/DND Setting
If multiple lines are available at your unit, press [ ] or [ ] to select the line to apply the settings to when you
select "FWD/DND Setting".
Setting
Description
Do Not Disturb
Enable DND (Do Not Disturb) to
reject all incoming calls.
FWD All
Forward all incoming calls to a
specified destination.
Value Range
Default
On, Off
Off
—
—
On, Off
Off
On/Off
Enable or disable the "FWD All"
setting.
Phone Number
Specify the number to forward calls
to when "FWD All" is enabled.
1–32 digits
—
Forward incoming calls to a specified
destination when you are on a call.
—
—
FWD Busy
On/Off
Enable or disable the "FWD Busy"
setting.
On, Off
Off
Phone Number
Specify the number to forward calls
to when "FWD Busy" is enabled.
1–32 digits
—
Forward incoming calls to a specified
destination if you do not answer after
a specified number of rings.
—
—
On, Off
Off
FWD No Ans
On/Off
Enable or disable the "FWD No
Ans" setting.
Phone Number
Specify the number to forward calls
to when "FWD No Ans" is enabled.
1–32 digits
—
Ring count
After you specify the phone number
to forward calls to, enter the number
of times the unit will ring before
forwarding the call.
0, 2–20
3
Note
•
For details about the FWD/DND settings when KX-UT113/KX-UT123/KX-UT133/KX-UT136 is
connected to a KX-NS1000 PBX, refer to the documentation of the KX-NS1000.
Document Version 2012-06
Operating Instructions
43
Customizing the Telephone
Language
Setting
Language
Description
Select the language to use for the
display.
Value Range
Default
Bosanski
Čeština
Dansk
Deutsch (DE)
English (UK)
English (US)
Español
Français
Français (Canada)
Hrvatski
Italiano
Magyar
Nederlands
Polski
Português
Română
Slovenčina
Slovenščina
Srpski
Svenska
Türkçe
Ελληνικά
Русский
Українська
English (US)
Value Range
Default
Date*1: dd/mm/yyyy
or mm/dd/yyyy
Time*2: 00:00–23:59
or 12:00–11:59 AM/
PM
—
Date and Time
Setting
Date and Time
*1
*2
Description
Set the date and time.
Pressing [#] switches the date format.
If the time format is not assigned in the configuration data, you can change the time format (12-hour or 24-hour) by pressing [*].
If the time format is set to 12-hour time in the configuration data, you can change the AM/PM setting by pressing [*].
Note
•
44
Daylight-saving time can be set through Web user interface programming. For details, consult your
administrator or dealer.
Operating Instructions
Document Version 2012-06
Customizing the Telephone
Information Display
Setting
Information Display
Description
Value Range
Default
View a variety of information about
the unit. Press [ ] and [ ] to display
the various settings. The following
settings can be viewed:
• Registration status to the SIP
server
• IP address
• Subnet mask address
• Default gateway address
• IP address of the DNS server 1
• IP address of the DNS server 2
• LLDP-MED
• LLDP-Timer
• IP Phone-VLAN ID
• IP Phone-Priority
• PC-VLAN ID
• PC-Priority
• ACS status
• Display lock status
• Firmware version
• Bluetooth headset status
(KX-UT248 only)
• MAC address
—
—
Network Settings
IMPORTANT
We recommend configuring these settings with your administrator or dealer. Network settings can also be
configured through Web user interface programming (Page 59). Contact your administrator or dealer for
further information.
Setting
Network
Description
Value Range
Default
Configure the basic network settings.
If you select "DHCP", you must then
select whether the DNS setting is
configured automatically or
manually. If you select "STATIC",
you must manually specify the IP
address, subnet mask, default
gateway, and DNS servers.
DHCP, STATIC
—
When DHCP is selected
Document Version 2012-06
Operating Instructions
45
Customizing the Telephone
Setting
Description
Value Range
Default
DNS
Select whether the DNS server
information should be obtained
automatically (i.e., provided by the
DHCP server) or if you will specify it
manually.
If you select "Manual", see "DNS1"
and "DNS2" below.
Manual, Automatic
Automatic
DNS1*1 (Manual DNS
only)
Enter the IP address of the primary
DNS server.
xxx.xxx.xxx.xxx
—
DNS2*1 (Manual DNS
only)
Enter the IP address of the
secondary DNS server.
If a secondary DNS server is not
required, leave this item blank.
xxx.xxx.xxx.xxx
—
When STATIC is selected
IP Address*1
Enter the IP address to assign to the
unit.
xxx.xxx.xxx.xxx
—
Subnet mask*1
Enter the subnet mask for your
network.
xxx.xxx.xxx.xxx
—
Default Gateway*1
Enter the IP address of the default
gateway for your network.
xxx.xxx.xxx.xxx
—
DNS1*1
Enter the IP address of the primary
DNS server.
xxx.xxx.xxx.xxx
—
DNS2*1
Enter the IP address of the
secondary DNS server.
If a secondary DNS server is not
required, leave this item blank.
xxx.xxx.xxx.xxx
—
LLDP-MED*3*4
Configure the LLDP-MED settings.
—
—
On/Off
Enable or disable the "LLDP-MED"
setting.
On, Off
On
Timer
Specify the LLDP Interval timer.
1–3600 seconds
30
PC port (KX-UT123/
KX-UT133/KX-UT136/
KX-UT248 only)
Specify the necessary settings for
using a PC over a VLAN.
—
—
0–4094
0
VLAN ID
Specify the VLAN ID.
Priority
Specify the priority of packets sent
from this unit.
0–7
0
Configure the VLAN (Virtual LAN)
settings.
—
—
VLAN
46
Operating Instructions
Document Version 2012-06
Customizing the Telephone
Setting
Description
Value Range
Default
Enable VLAN
Select whether to enable the VLAN
functionality.
Yes, No
No
IP Phone
Specify the necessary settings for
using the phone features over a
VLAN.
—
—
1–4094
2
VLAN ID
Specify the VLAN ID.
Priority
Specify the priority of packets sent
from this unit.
0–7
7
Specify the necessary settings for
using a PC over a VLAN.
—
—
1–4094
1
0–7
0
—
—
PC (KX-UT123/
KX-UT133/KX-UT136/
KX-UT248 only)
VLAN ID
Specify the VLAN ID.
Priority
Specify the priority of packets sent
from this unit.
Speed/Duplex
LAN port*2
Select the connection mode of the
LAN port.
Auto, 10M-Full,
10M-Half,
100M-Full,
100M-Half
Auto
PC port*2
(KX-UT123/
KX-UT133/KX-UT136/
KX-UT248 only)
Select the connection mode of the
PC port.
Auto, 10M-Full,
10M-Half,
100M-Full,
100M-Half
Auto
On, Off
Off
Embedded web*3
*1
*2
*3
*4
Select the connection mode
(combination of link speed and
duplex mode) of the LAN port and PC
port.
Enable or disable Web User
Interface Programming.
Press [ ] and [ ] to switch between these items.
The KX-UT248 supports Gigabit Ethernet. When connecting to a network that supports Gigabit Ethernet, select "Auto". For details,
consult your administrator or dealer.
This setting is not available if KX-UT113/KX-UT123/KX-UT133/KX-UT136 is connected to a KX-NS1000 PBX.
LLDP: Link Layer Discovery Protocol, MED: Media Endpoint Discovery
Document Version 2012-06
Operating Instructions
47
Customizing the Telephone
Network Test
Setting
Network Test
Description
Value Range
Default
Confirm whether other network
devices (e.g., SIP server, routers,
switching hubs) respond to network
requests. When you select this item,
enter the IP address of the device to
which you want to test the
connection.
If a device does not respond, first
check the unit's network settings, and
then check the device's network
settings and connection.
xxx.xxx.xxx.xxx
—
Description
Value Range
Default
—
—
Description
Value Range
Default
View the version of the currently
installed firmware. If a newer version
is available, its version is also
displayed. In this case, press Update
to update the firmware.
—
—
Restart
Setting
Restart
Restart the unit (Page 76).
Firmware version
Setting
Firmware version
Note
•
48
Your phone system dealer may offer new features or an improved version of the unit's software from
time to time. If you set the unit software update setting to manual mode through the Web user interface,
you need to download the update when "Update version. Press OK." is displayed. Contact your
administrator or dealer for further information.
Operating Instructions
Document Version 2012-06
Customizing the Telephone
Call Block
Setting
Call Block
Description
Value Range
Default
Register telephone numbers so that
calls received from those numbers
are blocked. You can also delete
registered numbers.
—
—
To register
1. Press Add .
2. Enter the telephone number to
block, and then press [ENTER].
To edit
1. Press [ ] or [ ] to select the
blocked telephone number to
edit.
2. Press Edit .
3. Edit the number as necessary,
and then press [ENTER].
To delete
1. Press [ ] or [ ] to select the
blocked telephone number to
delete.
2. Press Erase .
3. Select "Yes", and then press
[ENTER].
Document Version 2012-06
Operating Instructions
49
Customizing the Telephone
Bluetooth Headset (KX-UT248 only)
Setting
Bluetooth Headset
Description
Configure the Bluetooth headset
settings.
Value Range
Default
—
—
—
—
1–4 digits
0000
When a Bluetooth headset is not registered
Add new device
Enter PIN
Register a Bluetooth headset on the
unit.
Enter the Pass Key for your
Bluetooth headset.
When a Bluetooth headset is registered
50
Disconnect
Disconnect the Bluetooth headset
from the unit when the Bluetooth
headset is registered to the unit.
—
—
Connect
Connect the Bluetooth headset to the
unit when the Bluetooth headset is
registered to the unit.
—
—
Deregistration
Deregister a Bluetooth headset from
the unit.
—
—
Operating Instructions
Document Version 2012-06
Customizing the Telephone
Entering Characters
The dial keys are used to enter characters and numbers. Each dial key has multiple characters assigned to it.
(For example, A, B and C are assigned to the 1 key.)
To enter a character, press the corresponding dial key until the character you want appears. To enter another
character that is assigned to the same key, first press [ ] to move the cursor to the right.
Example
To enter "DESK", press the keys as follows:
Input:
(right)
Display:
For details about the characters assigned to each key, see "Character Tables (Page 53)".
Deleting characters
Press
Clear
to delete the last character entered.
Note
•
Press and hold
Clear
to delete all entered text.
Switching between uppercase and lowercase
Press
A/a
to switch between uppercase entry and lowercase entry.
Modifying entered text
Use [ ] and [ ] to move the cursor to where you want to modify the text. Then, modify the text as follows:
• Press Clear to delete the character under the cursor.
•
Press a dial key to insert a character at the cursor’s location.
•
Press
A/a
to change the case of the character under the cursor.
Document Version 2012-06
Operating Instructions
51
Customizing the Telephone
Note
•
•
If the maximum number of characters has been entered, entering another character will overwrite the
character under the cursor.
If the entered texts spans two or more lines, you can also move the cursor using [ ] and [ ].
Character entry modes
The six character entry modes let you enter a variety of characters.
The following character modes are available:
• Latin (ABC)
• Numeric (0–9)
• Greek (ΑΒΓ)
• Extended 1 (AÄÅ)
• Extended 2 (SŚŠ)
• Cyrillic (АБВ)
For details about which characters are available in each mode, see "Character Tables (Page 53)".
To select a character mode
1. When entering characters, press 1/A/? .
2. Press [ ] or [ ] to select the desired character entry mode.
3. Press [ENTER].
Note
•
52
Depending on the type of information you are entering, you cannot change character modes. For
example, when you are entering a phone number, only numeric mode is available.
Operating Instructions
Document Version 2012-06
Customizing the Telephone
Character Tables
ABC (Latin)
Button
Characters
Note
•
For each button, the upper row shows the characters entered in uppercase mode, and the lower row
shows the characters entered in lowercase mode.
Document Version 2012-06
Operating Instructions
53
Customizing the Telephone
0–9 (Numeric)
Button
54
Characters
Operating Instructions
Document Version 2012-06
Customizing the Telephone
ΑΒΓ (Greek)
Button
Characters
Note
•
For each button, the upper row shows the characters entered in uppercase mode, and the lower row
shows the characters entered in lowercase mode.
Document Version 2012-06
Operating Instructions
55
Customizing the Telephone
AÄÅ (Latin Extended 1)
Button
Characters
Note
•
56
For each button, the upper row shows the characters entered in uppercase mode, and the lower row
shows the characters entered in lowercase mode.
Operating Instructions
Document Version 2012-06
Customizing the Telephone
SŚŠ (Latin Extended 2)
Button
Characters
Note
•
For each button, the upper row shows the characters entered in uppercase mode, and the lower row
shows the characters entered in lowercase mode.
Document Version 2012-06
Operating Instructions
57
Customizing the Telephone
АБВ (Cyrillic)
Button
Characters
Note
•
58
For each button, the upper row shows the characters entered in uppercase mode, and the lower row
shows the characters entered in lowercase mode.
Operating Instructions
Document Version 2012-06
Customizing the Telephone
Web User Interface
Programming
The unit provides a Web-based interface for configuring
various settings and features, including some that are
not programmable directly from the unit. The following
list contains some useful features that are
programmable through the Web user interface.
For details, consult your administrator or dealer.
• Basic network settings*1 (Page 45)
• User password (for access to Web user interface)
• HTTP authentication settings
• Date and time settings*1 (Page 44)
• Default outgoing line
• Call rejection phone numbers*1 (Page 49)
• Block caller ID
• Block anonymous calls
• Do Not Disturb*1 (Page 43)
• Call forward*1 (Page 43)
• Flexible button settings (Page 35) (DN, One-Touch,
Headset, etc. KX-UT133/KX-UT136/KX-UT248
only)
• Key click tone
• Extension PIN
• Phonebook import and export (Page 37)
*1
These settings can also be configured directly through the unit.
Notice
•
•
Each time you want to access the Web user
interface, you must enable Web programming
(Page 47).
Web user interface programming is not
available if KX-UT113/KX-UT123/KX-UT133/
KX-UT136 is connected to a KX-NS1000 PBX.
Document Version 2012-06
Operating Instructions
59
Installation and Setup
Installation and Setup
Notice
•
Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of
improper installation or operation inconsistent with this documentation.
Attaching/Removing the Stand
Attaching the Stand
Notice
•
If you place the display face down when you attach the stand, be sure to place a soft cloth under the
display. Failure to do so may result in damage to the display.
For KX-UT113/KX-UT123:
1. Insert the catches of the stand into hooks located in the unit.
2. Gently push the stand in the direction indicated until it locks into place.
The stand will be mounted.
For KX-UT133/KX-UT136/KX-UT248:
1. Insert the catches (1) of the stand into hooks located in the unit.
2. Gently push the stand in the direction indicated until it locks into place.
The stand will be mounted in the high position.
A
60
Operating Instructions
Document Version 2012-06
Installation and Setup
Removing the Stand
For KX-UT113/KX-UT123:
1. Remove the stand in the direction indicated while pushing the catches of the stand with both hands as
shown.
For KX-UT133/KX-UT136/KX-UT248:
1. Hold the stand with both hands.
2. Gently rotate the stand in the direction indicated until it is released.
Adjusting from High to Low Position (KX-UT133/KX-UT136/KX-UT248 only)
Document Version 2012-06
Operating Instructions
61
Installation and Setup
1. Tilt the stand in the direction indicated while pushing the PUSH mark with both hands as shown until it
locks into the low position (2).
B
Adjusting from Low to High Position (KX-UT133/KX-UT136/KX-UT248 only)
1. Tilt the stand in the direction indicated while pushing the PUSH mark with both hands as shown until it
locks into the high position (1).
A
62
Operating Instructions
Document Version 2012-06
Installation and Setup
Connections
This section explains the ports and connectors on the unit.
Connections for AC Adaptor/LAN/PC
For KX-UT113/KX-UT123:
Optional AC adaptor
To a Switching Hub
To a PC (KX-UT123 only)
Ethernet cables
To a handset jack
(handset)
Clamp
AC adaptor
Handset
Headset
For KX-UT133/KX-UT136/KX-UT248:
Optional AC adaptor
To a Switching Hub
To a PC
Ethernet cables
To a handset jack
(handset)
A
B
Clamp
AC adaptor
Handset
Headset
A EHS jack
B Headset jack
CAUTION
Optional AC Adaptor
• Use the following Panasonic AC adaptor:
– For users in the United States: KX-A239 (PQLV206)
– For users in Canada: KX-A239X (PQLV206)
Document Version 2012-06
Operating Instructions
63
Installation and Setup
•
The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near
the unit and is easily accessible.
When connecting a headset
• Ensure that the headset cord has slack and is not pulled tight during use to prevent damage to the
connectors.
• Cords used to connect devices to the EHS jack or headset jack must be less than 3 m (9.8 ft) in
length.
Notice
•
The following headsets can be used with this unit. (Not all operations with the headsets can be
guaranteed.)
– Wired headsets
Panasonic KX-TCA400 or KX-TCA430
– EHS headsets (KX-UT133/KX-UT136/KX-UT248 only)
Selected Plantronics®-brand headsets
– Bluetooth headsets (KX-UT248 only)
Selected Plantronics-brand headsets
Selected GN Netcom-brand headsets
For up-to-date information about headsets that have been tested with this unit, refer to the
following web sites:
http://www.panasonic.com/sip (for users in the United States)
http://panasonic.net/pcc/support/sipphone (for users in Canada)
When selecting Ethernet cables (not included)
• Use flexible, high-quality, snagless (without strain relief) cables. Do not use cables with coating
that may tear or crack when bent.
To prevent damage to the cables, use cables that do not protrude from the bottom of the base.
Connect the cables as shown in the following illustration.
Incorrect
Ethernet cable
Correct
Ethernet cable
60 mm (2 3/8 in)
or less
•
•
For KX-UT113/KX-UT123/KX-UT133/KX-UT136: Use a straight CAT 5 (or higher) Ethernet cable
(not included) that is 6.5 mm (1/4 in) in diameter or less.
For KX-UT248: Use a straight CAT 5e (or higher) Ethernet cable (not included) that is 6.5 mm
(1/4 in) in diameter or less.
When connecting to a switching hub
• If PoE is available, an AC adaptor is not needed.
• For KX-UT113/KX-UT123/KX-UT133/KX-UT136: This unit complies with the PoE Class 2 standard.
• For KX-UT248: This unit complies with the PoE Class 3 standard.
64
Operating Instructions
Document Version 2012-06
Installation and Setup
When connecting a PC
• Only a PC can be connected to the PC port. Other SIP phones, or network devices such as routers
or switching hubs, cannot be connected.
• The PC port does not support PoE for connected devices.
When connecting cables and the AC adaptor
• Ensure that the Ethernet cables and the AC adaptor cord are clamped to prevent damage to the
connectors.
When registering a Bluetooth headset (KX-UT248 only)
• One Bluetooth headset can be registered to this unit. For details, see "Registering the Bluetooth
headset (Page 74)".
Document Version 2012-06
Operating Instructions
65
Installation and Setup
Connections for Handset
For KX-UT113/KX-UT123:
For KX-UT133/KX-UT136/KX-UT248:
66
Operating Instructions
Document Version 2012-06
Installation and Setup
Wall Mounting
Before Mounting on a Wall
To mount the unit, it is necessary to remove the stand. For details, see "Removing the Stand (Page 61)".
Mounting the Unit
WARNING
•
•
•
•
•
Do not mount the unit in a manner other than that described in this section.
Make sure that the wall that the unit will be attached to is strong enough to support the unit. If not, it is
necessary for the wall to be reinforced. For information about the weight of the unit, see "Specifications
(Page 77)".
Only use the optional wall mount kit with the unit. The wall mount kit includes the necessary screws,
washers, and wall mounting adaptor.
When driving the screws into the wall, be careful to avoid touching any metal laths, wire laths or metal
plates in the wall.
When this unit is no longer in use, make sure to detach it from the wall.
CAUTION
•
Make sure the cables are securely fastened to the wall.
Notice
•
If you place the display face down when you attach the wall mounting adaptor, be sure to place a soft
cloth under the display before attaching the adaptor. Failure to do so may result in damage to the
display.
1. Insert the 3 tabs (for KX-UT113/KX-UT123) or 5 tabs (for KX-UT133/KX-UT136/KX-UT248) of the wall
mounting adaptor into the designated openings in the base, and then slide the wall mounting adaptor in
the direction of the arrow until it clicks.
For KX-UT113/KX-UT123:
Document Version 2012-06
Operating Instructions
67
Installation and Setup
For KX-UT133/KX-UT136/KX-UT248:
2. Fasten the wall mounting adaptor to the base with 1 screw. (Recommended torque: 0.4 N·m [4.08 kgf·cm/
3.54 lbf·in] to 0.6 N·m [6.12 kgf·cm/5.31 lbf·in])
For KX-UT113/KX-UT123:
68
Operating Instructions
Document Version 2012-06
Installation and Setup
For KX-UT133/KX-UT136/KX-UT248:
3. Connect the cables to the unit, and run the cables through the wall mounting adaptor, as shown in the
illustration below.
For details about connecting the cables, see "Connections (Page 63)".
Note
•
The cables can also be run from the bottom of the unit.
For KX-UT113/KX-UT123:
AC adaptor
Ethernet cables
40 mm (1 37/64 in)
or less
Document Version 2012-06
Operating Instructions
69
Installation and Setup
For KX-UT133/KX-UT136/KX-UT248:
Ethernet cables
AC adaptor
40 mm (1 37/64 in)
or less
4. Drive the 2 screws into the wall either 83 mm (3 1/4 in) or 100 mm (3 15/16 in) apart, and mount the unit on
the wall.
For KX-UT113/KX-UT123:
83 mm
100 mm (3 1/4 in)
(3 15/16 in)
Washer
Drive the screw
to this point.
70
Operating Instructions
Document Version 2012-06
Installation and Setup
For KX-UT133/KX-UT136/KX-UT248:
83 mm
100 mm (3 1/4 in)
(3 15/16 in)
Washer
Drive the screw
to this point.
Note
•
•
You can find a wall mounting template at the end of this manual.
For information about locking the handset, see "Hooking the Handset (Page 72)".
Document Version 2012-06
Operating Instructions
71
Installation and Setup
Hooking the Handset
You can hook the handset with following operations.
To Hook the Handset During a Conversation
1. Hook the handset over the top edge of the unit.
To Lock the Handset Hook when the Unit is Wall Mounted
1. Remove the handset hook from the slot.
2. Turn it up-side-down.
3. Slide the handset hook back into the slot until it locks.
72
Operating Instructions
Document Version 2012-06
Installation and Setup
4. Handset is safely hooked when it is in the cradle.
Document Version 2012-06
Operating Instructions
73
Installation and Setup
Using a Headset
For KX-UT133/KX-UT136/KX-UT248, if a headset is
connected, you must enable Headset mode using the
Headset button (flexible button).
To enable Headset mode, press the Headset button
(flexible button).
Note
•
•
•
For KX-UT113/KX-UT123, the Headset mode is
automatically enabled when connecting a
headset.
The Headset button light shows the current
status as follows:
Off: Headset mode off
Red on: Headset mode on
For details about setting a flexible button as the
Headset button, consult your administrator or
dealer.
For a Bluetooth Headset User
(KX-UT248 only)
A KX-UT248 can be used with a Bluetooth headset.
Before using the Bluetooth headset, you need to
register it to the unit.
Registering the Bluetooth headset
Set the headset to pairing mode by following the
instructions in the headset's documentation.
1. In stand-by mode, press Setting .
2. Press [ ] or [ ] to select "Bluetooth Headset",
and then press [ENTER].
3. Press [ENTER] to select "Add new device".
4. Enter the Pass Key for your Bluetooth headset in
"Enter PIN", and then press [ENTER].
•
is displayed when headset is
disconnected and the unit is in stand-by
mode.
Connecting the Bluetooth headset
1. In stand-by mode, press Setting .
2. Press [ ] or [ ] to select "Bluetooth Headset",
and then press [ENTER].
3. Press [ ] or [ ] to select "Connect", and then
press [ENTER].
Note
•
is displayed when headset is connected
and the unit is in stand-by mode.
Deregistering the Bluetooth headset
1. In stand-by mode, press Setting .
2. Press [ ] or [ ] to select "Bluetooth Headset",
and then press [ENTER].
3. Press [ ] or [ ] to select "Deregistration", and
then press [ENTER].
Switching from your Bluetooth headset to the
handset during a call
1. Lift the handset off of its cradle.
Operating Distance
Please keep units containing Bluetooth modules 3 m or
more apart from each other. Also, if a Bluetooth headset
is in use near a telephone containing a Bluetooth
module other than the one it is registered to, noise may
be heard. To improve the signal, move away from the
telephone and closer to the one it is registered to.
Noise
Note
•
Note
For more information regarding the Pass
Key, see the documentation for your
headset, or consult the Bluetooth headset’s
manufacturer.
Disconnecting the Bluetooth headset
1. In stand-by mode, press Setting .
2. Press [ ] or [ ] to select "Bluetooth Headset",
and then press [ENTER].
3. Press [ ] or [ ] to select "Disconnect", and then
press [ENTER].
Signals are transmitted between the unit and the
Bluetooth headset using radio waves. For maximum
distance and noise free operation, it is recommended
that the unit is situated away from electrical appliances
such as faxes, radios, personal computers, or
microwaves.
• Systems using the 2.4 GHz ISM (Industrial,
Scientific and Medical) band may interfere with this
product. Examples of such systems are cordless
telephones, wireless LAN, Home RF, microwave
ovens and other ISM devices. These systems may
cause minor noise.
Notice
Operation is subject to the following two conditions:
74
Operating Instructions
Document Version 2012-06
Installation and Setup
1. this unit may not cause interference, and
2. this unit must accept any interference, including
interference that may cause undesired
operation of the unit. Privacy of
communications may not be ensured when
using the unit.
Setting Up the Unit
This section explains the settings that you can configure
when you start the unit.
Accessing the start-up settings
1. Connect the unit to an Ethernet cable capable of
delivering power (PoE compliant), or use an
optional AC adaptor to supply power.
2. Connect the unit to the network.
3. On the start-up screen, press Setup .
4. Select the item for the settings you want to
configure.
Start-up menu
You can configure the following start-up settings:
1. Information Display (Page 45)
View a variety of information about the unit.
2. Network Settings (Page 45)
3.
4.
5.
6.
7.
Document Version 2012-06
Assign an IP address in order to connect to the
network and use the unit.
Network Test (Page 48)
Confirm the connection of network devices (e.g.,
the SIP server, routers, switching hubs).
ECO Mode (Page 41)
Enable ECO mode.
Language (Page 44)
If you prefer to use a language other than English,
change your language settings.
Restart (Page 48)
Restart the unit for new settings to take effect.
Firmware version (Page 48)
Check the firmware version of the unit.
Operating Instructions
75
Installation and Setup
Maintaining the Unit
When cleaning the body
• To avoid damaging the unit, disconnect the
Initializing the Unit
Doing an initialization resets some or all settings to their
default values. For details, consult your administrator or
dealer.
Restarting the Unit
When some of the settings on the unit have been
changed via Web user interface programming or
configuration file programming, the unit must be
restarted.
1. In stand-by mode, press Setting .
2. Press [ ] or [ ] to select "Restart", and then press
[ENTER].
3. Press [ ] or [ ] to select "Yes", and then press
[ENTER].
• To cancel, select "No".
•
•
•
Ethernet cable and all other cables from the unit
before cleaning. If the unit is powered with an AC
adaptor, disconnect the AC adaptor from the unit
and power outlet before cleaning.
If the unit becomes particularly dirty, apply a light
kitchen cleanser to a soft cloth, wring the cloth
thoroughly, and then wipe the unit. When finished,
dry the unit with a soft and dry cloth.
To avoid damage or discoloration, do not clean the
unit with the any of following materials or with
cleaners that contain any of the following materials:
– Petroleum
– Scouring powder
– Alcohol
– Paint thinner
– Benzine
– Wax
– Hot water
– Powdered soap
When using chemical cleansers, follow the
instructions on the label carefully.
Cleaning the Unit
Clean the unit periodically by wiping it with a soft and
dry cloth.
When cleaning the unit, observe the following
precautions.
When cleaning the display
• Wipe the display with only the following types of
•
76
materials:
– A soft and dry cloth.
– A soft cloth with very small quantity of neutral
detergent or ethyl alcohol.
Do not press or rub the display with too much force.
Operating Instructions
Document Version 2012-06
Appendix
Appendix
Specifications
For KX-UT113/KX-UT123/KX-UT133/KX-UT136
Specifications
Item
KX-UT113
KX-UT123
LCD Display
242 ´ 55 pixels,
3 lines
—
Flexible Buttons
242 ´ 109 pixels,
6 lines
Always On/Automatic/Always Off
—
24
VoIP Connection
Method
SIP
VoIP Audio Codec
G.722, G.711, G.729A, G.726
Ethernet Interface
10Base-T/100Base-TX
IP Address Mode
Automatic (DHCP), Manual (static)
Speaker
1
Microphone
1
Ethernet Port (LAN)
1 (RJ45)
2 (RJ45)
Headset Jack
1 (ø 2.5 mm [3/32 in])
EHS Jack
Dimensions
(Width ´ Depth ´ Height;
handset on cradle, stand
attached)
Weight (with handset,
handset cord and stand)
PoE
Power Consumption
KX-UT136
Monochrome graphical
LCD Size
LCD Backlight
KX-UT133
—
1 (ø 3.5 mm [1/8 in], for EHS only)
205 mm ´ 160 mm ´ 170 mm
(8.07 in ´ 6.30 in ´ 6.69 in)
860 g (1.90 lb)
"High" position:
267 mm ´ 170 mm ´ 180 mm
(10.5 in ´ 6.69 in ´ 7.09 in)
"Low" position:
267 mm ´ 187 mm ´ 155 mm
(10.5 in ´ 7.36 in ´ 6.10 in)
870 g (1.92 lb)
1120 g (2.47 lb)
IEEE 802.3af Class 2 standard compliant
PoE
Stand-by: approx. 1.8 W (ECO mode off), approx. 1.3 W (ECO mode on)
Talking: approx. 2 W (ECO mode off), approx. 1.5 W (ECO mode on)
AC Adaptor
Stand-by: approx. 1.6 W (ECO mode off), approx. 1 W (ECO mode on)
Talking: approx. 2 W (ECO mode off), approx. 1.5 W (ECO mode on)
Maximum Power
Consumption
Document Version 2012-06
6W
Operating Instructions
77
Appendix
Specifications
Item
KX-UT113
Operating Environment
KX-UT123
KX-UT133
KX-UT136
0 °C to 40 °C (32 °F to 104 °F)
For KX-UT248
Item
LCD Display
LCD Size
LCD Backlight
Specifications
4-level grayscale graphical
4.4 inch
Always On/Automatic/Always Off
Flexible Buttons
24 (Three pages of eight flexible buttons are shown on the display)
VoIP Connection
Method
SIP
VoIP Audio Codec
G.722, G.711, G.729A, G.726
Ethernet Interface
10Base-T/100Base-TX/1000Base-T
IP Address Mode
Automatic (DHCP), Manual (static)
Speaker
1
Microphone
1
Ethernet Port (LAN)
Headset Jack
2 (RJ45)
1 (ø 2.5 mm [3/32 in])
EHS Jack
1 (ø 3.5 mm [1/8 in], for EHS only)
Bluetooth
1 (Bluetooth wireless technology 2.0)
Dimensions
(Width ´ Depth ´ Height;
handset on cradle, stand
attached)
Weight (with handset,
handset cord and stand)
PoE
"High" position:
267 mm ´ 170 mm ´ 180 mm
(10.5 in ´ 6.69 in ´ 7.09 in)
"Low" position:
267 mm ´ 187 mm ´ 155 mm
(10.5 in ´ 7.36 in ´ 6.10 in)
1130 g (2.49 lb)
IEEE 802.3af Class 3 standard compliant
Power Consumption
PoE
Stand-by: approx. 3.5 W (ECO mode off), approx. 2.3 W (ECO mode on)
Talking: approx. 4.1 W (ECO mode off), approx. 2.5 W (ECO mode on)
AC Adaptor
Stand-by: approx. 4.0 W (ECO mode off), approx. 2.2 W (ECO mode on)
Talking: approx. 4.5 W (ECO mode off), approx. 2.7 W (ECO mode on)
Maximum Power
Consumption
78
Operating Instructions
7.5 W
Document Version 2012-06
Appendix
Item
Specifications
Operating Environment
0 °C to 40 °C (32 °F to 104 °F)
Document Version 2012-06
Operating Instructions
79
Appendix
Troubleshooting
Common Issues and Solutions
General Use
Issue
The display is blank.
Possible Cause & Solution
•
Reference
The unit is not receiving power.
→ The unit is not designed to function when there is a power
failure. Make sure that the device supplying PoE is
receiving power and that the Ethernet cable is properly
connected. If an AC adaptor is connected, confirm that the
AC adaptor is connected and receiving power.
Page 63
The display is not shown
well.
•
The display's contrast is too low.
→ Adjust the display's contrast.
Page 42
The unit is not performing
properly.
•
Cables or cords are not connected properly.
→ Check all connections.
Page 63
•
Your connection settings are incorrect.
→ Consult your administrator to confirm that your settings are
correct.
→ If the problem persists, consult your dealer.
Page 38
•
An error has occurred.
→ Restart the unit.
Page 76
is displayed on the
screen.
•
Registration to the SIP server has been lost.
→ Consult your administrator or dealer.
I cannot hear a dial tone.
•
Confirm that the LAN cable is properly connected.
I cannot cancel the display
lock.
•
The PIN number you entered was incorrect.
→ Consult your administrator or dealer.
—
I forgot my PIN number.
•
Consult your administrator or dealer.
—
The date and time are not
correct.
•
Adjust the date and time of the unit.
The Message/Ringer lamp
is lit.
•
You received a voice message while you were on the phone
or away from your desk.
→ Check the voice message.
80
Operating Instructions
—
Page 63
Page 44
Page 33
Document Version 2012-06
Appendix
Making and Receiving Calls
Issue
I cannot make calls.
Possible Cause & Solution
•
Reference
Your phone system/service has disabled service for your unit.
→ On the Information Display screen (Page 45), if "Not
registered" is displayed in "Status", consult your
administrator or dealer.
•
•
•
I cannot make long
distance calls.
•
The unit does not ring
when a call is received.
•
While talking to an outside
party, the line is
disconnected.
•
—
The phone number was entered incorrectly.
→ Confirm that you have entered the phone number of the
other party correctly.
→ Consult your administrator or dealer.
Page 25
The unit is downloading a firmware update.
→ You cannot make calls while the unit is downloading
updates. Wait for the update to finish, and then try making
a call.
—
The phonebook list is being imported or exported.
→ Wait a few minutes for the operation to complete.
→ Confirm with your administrator or dealer.
—
Your telephone service does not allow you to make long
distance calls.
→ Make sure that you have subscribed to your telephone
company’s long distance service.
—
The ringer is turned off.
→ Press [ ] while a call is being received, or change the
ringer volume setting.
Page 41
Your phone system/service may impose a time limit on outside
calls.
→ Consult your dealer to extend the time limit, if necessary.
—
Sound Quality
Issue
The other party cannot
hear my voice.
Document Version 2012-06
Possible Cause & Solution
Reference
•
The unit is muted.
→ Press [MUTE] to turn off the mute feature.
•
If you are using the speakerphone, objects may be obstructing
the microphone.
→ Do not obstruct the unit's microphone during calls. Keep
your hands, as well as common objects such as folders,
cups, and coffee pots away from the unit during calls.
Page 31
—
Operating Instructions
81
Appendix
Issue
Sound cuts out; I can hear
myself through the
speaker.
Possible Cause & Solution
Reference
•
You are too far away from the microphone.
→ Try speaking closer to the microphone.
—
•
The environment is not suited to speakerphone calls.
→ Do not use the unit within 2 m (6.6 ft) of projectors, air
conditioning devices, fans, or other audible or electrical
noise emitting devices.
→ If using the unit in a room with windows, close the curtains
or blinds to prevent echoes.
→ Use the unit in a quiet environment.
—
•
The unit was moved during a call.
→ Do not move the unit while on a call.
—
•
Objects are obstructing the microphone.
→ Do not obstruct the unit during calls. Keep your hands, as
well as common objects such as folders, cups, and coffee
pots away from the unit during calls.
—
The other party is using a half-duplex speakerphone.
→ If the other party is using a half-duplex speakerphone,
sound may cut out occasionally during calls. For best
performance, the other party should use a full-duplex
speakerphone.
—
<KX-UT248 only>
• Just after a call begins, the unit may not have yet adjusted
itself to the call’s environment.
→ Just after a call begins, take turns with the other party
talking to each other. The unit will adjust itself in
accordance with the call environment so that both you and
the other party can hear each other as clearly as possible.
—
Possible Cause & Solution
Reference
•
Phonebook List
Issue
I cannot add or edit entries
to the phonebook list.
82
Operating Instructions
•
The phonebook list is full.
→ Delete any unnecessary entries. The maximum number of
entries in the phonebook list is 500 for the KX-UT123/
KX-UT133/KX-UT136/KX-UT248 and 100 for the
KX-UT113.
Page 36
Document Version 2012-06
Appendix
Bluetooth Headset (KX-UT248 only)
Issue
I cannot have a
conversation using the
Bluetooth headset.
Possible Cause & Solution
•
•
•
Document Version 2012-06
Reference
Make sure that the headset is properly registered to the unit.
Make sure that the headset is properly charged by following
the instructions in the headset's documentation.
Remove the wired headset from the headset jack. Priority is
given to the wired headset when both are connected.
—
Operating Instructions
83
Appendix
Error Messages
During operation, error messages might appear on the unit. The following table lists these messages and
possible causes and solutions.
Message
IP address collision
Possible Cause & Solution
•
Illegal IP address
Reference
The unit’s network settings are incorrect.
→ Consult your system administrator or dealer.
—
Invalid IP address
Check LAN cable.
•
The LAN cable is not connected.
→ Check all connections.
Page 63
Memory Full
•
A new entry for the phonebook or call block list cannot be
stored because the phonebook or call block list is full.
→ Erase unneeded entries.
Page 37
Page 36
Page 28
No Entries
•
The phonebook or call block list contains no entries.
→ Store entries in the phonebook or call block list.
Please wait…
•
The unit is still starting up.
→ If you have a lot of entries in the phonebook list, the unit
may take a while to start up. This is normal.
84
Operating Instructions
—
Document Version 2012-06
Appendix
Revision History
KX-UT113/KX-UT123/KX-UT133/KX-UT136 Software File Version
01.025
Changed Contents
•
Removing a Party from the Conference (Page 32)
•
Ringer (Page 41)
•
Initializing the Unit (Page 76)
Document Version 2012-06
Operating Instructions
85
Appendix
KX-UT113/KX-UT123/KX-UT133/KX-UT136 Software File Version
01.080
New Contents
•
Key Click Tone (Page 42)
Changed Contents
86
•
Dialing by Using Call Logs (Page 26)
•
Rejecting Calls (Page 27)
•
Transferring a Call (Call Transfer) (Page 30)
•
Checking Missed Calls (Page 33)
•
Adding a Phonebook Entry from the Incoming or Missed Call Log (Page 36)
Operating Instructions
Document Version 2012-06
Appendix
KX-UT113/KX-UT123/KX-UT133/KX-UT136/KX-UT248 Software
File Version 01.160
Changed Contents
•
Logging in to or Logging out of a Group (KX-UT133/KX-UT136/KX-UT248 only) (Page 34)
•
Flexible Buttons (KX-UT133/KX-UT136/KX-UT248 only) (Page 35)
•
Available Settings (Page 39)
•
Settings Details (Page 41)
Document Version 2012-06
Operating Instructions
87
Open Source Software
Open Source Software
Parts of this product use Open Source Software. Relevant conditions apply to this software. Panasonic cannot
accept inquiries regarding the content of the following copyright and license information.
<<NetBSD kernel>>
This product uses a part of NetBSD kernel.
The use of a part of NetBSD kernel is based on the typical BSD style
license below.
Copyright (c)
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software
must display the following acknowledgement:
This product includes software developed by the University of
California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its contributors
may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
However, parts of the NetBSD Kernel are provided with the following copyright notices.
Copyright (c) 1980, 1983, 1988, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1980, 1986, 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1980, 1986, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1980, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1985, 1986, 1988, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1988, 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1988, 1990, 1993, 1994, 1995 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1988, 1990, 1993, 1995 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1988, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1988, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1988, 1993, 1995 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1990, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1990, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1991, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1991, 1993, 1995 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1986, 1993, 1994, 1995 The Regents of the University of California. All rights reserved.
88
Operating Instructions
Document Version 2012-06
Open Source Software
Copyright (c) 1982, 1986, 1993, 1995 The Regents of the University of California. All rights reserved.
Copyright (c) 1982, 1988, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1983, 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1983, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1985, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1985, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1987, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1987, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1987, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988 Regents of the University of California. All rights reserved
Copyright (c) 1988 Stephen Deering.
Copyright (c) 1988 University of Utah.
Copyright (c) 1988, 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988, 1992, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1988, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1989 The Regents of the University of California. All rights reserved.
Copyright (c) 1989, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1989, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1989, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1990, 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1990, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1991, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1991, 1993, 1994 The Regents of the University of California. All rights reserved.
Copyright (c) 1992 Regents of the University of California. All rights reserved.
Copyright (c) 1992, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1993 Adam Glass
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Copyright (c) 1994 Gordon W. Ross
Copyright (c) 1994 Winning Strategies, Inc. All rights reserved.
Copyright (c) 1995 The Regents of the University of California. All rights reserved.
Copyright (C) 1995, 1996, 1997, and 1998 WIDE Project. All rights reserved.
Copyright (c) 1996 The Regents of the University of California. All rights reserved.
Copyright (c) 1996 John S. Dyson All rights reserved.
Copyright (c) 1996 Matt Thomas. All rights reserved.
Copyright (c) 1996 Matthew R. Green. All rights reserved.
Copyright (c) 1996 Paul Kranenburg
Copyright (c) 1996, 1997, 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1996, 2000 Christopher G. Demetriou. All rights reserved.
Copyright (c) 1996,1999 by Internet Software Consortium.
Copyright (c) 1996-1999 by Internet Software Consortium.
Copyright (c) 1997 Jonathan Stone and Jason R. Thorpe. All rights reserved.
Copyright (c) 1997 Christos Zoulas. All rights reserved.
Copyright (c) 1997 Manuel Bouyer. All rights reserved.
Copyright (c) 1997, 1998 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 1999, 2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997, 1998, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1997,98 The NetBSD Foundation, Inc. All rights reserved.
Copyright (C) 1997-2000 Sony Computer Science Laboratories Inc. All rights reserved.
Copyright (c) 1997-2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998 Todd C. Miller <Todd.Miller@courtesan.com> All rights reserved.
Copyright (c) 1998, 1999 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 1999, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1998, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999 The NetBSD Foundation, Inc. All rights reserved.
Copyright (C) 1999 WIDE Project. All rights reserved.
Document Version 2012-06
Operating Instructions
89
Open Source Software
Copyright (c) 1999, 2000 Jason L. Wright (jason@thought.net) All rights reserved.
Copyright (c) 1999, 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999, 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2000 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2000, 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2000, 2001, 2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2002 The NetBSD Foundation, Inc. All rights reserved.
Copyright 1998 Massachusetts Institute of Technology. All rights reserved.
Copyright 2001 Wasabi Systems, Inc. All rights reserved.
Portions Copyright (c) 1993 by Digital Equipment Corporation.
Portions Copyright (c) 1995 by International Business Machines, Inc.
Copyright (c) 1983, 1989 The Regents of the University of California. All rights reserved.
Copyright (c) 1996 by Internet Software Consortium. All rights reserved.
Copyright (c) 1980, 1986, 1989 Regents of the University of California. All rights reserved.
Copyright (c) 1988 The Regents of the University of California. All rights reserved.
Copyright (c) 1992, 1993 The Regents of the University of California. All rights reserved.
Copyright (c) 1994 Christopher G. Demetriou. All rights reserved.
Copyright (c) 1997 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1999 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 2001 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1996 Gardner Buchanan <gbuchanan@shl.com> All rights reserved.
Parts of the NetBSD Kernel are provided with the licenses that are slightly different from the
above Berkeley-formed license. Please refer the source code of the NetBSD Kernel about the details.
The source code of the NetBSD Kernel is provided by the NetBSD CVS Repositories
(http://cvsweb.netbsd.org/bsdweb.cgi/), and this product includes parts of the source code in the
following directories.
http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/kern/
http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/net/
http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/netinet/
<<MD5>>
This software uses the Source Code of RSA Data Security, Inc. described in the
RFC1321 (MD5 Message-Digest Algorithm).
----------------------------------------------------------------Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All
rights reserved.
License to copy and use this software is granted provided that it
is identified as the "RSA Data Security, Inc. MD5 Message-Digest
Algorithm" in all material mentioning or referencing this software
or this function.
License is also granted to make and use derivative works provided
that such works are identified as "derived from the RSA Data
Security, Inc. MD5 Message-Digest Algorithm" in all material
mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either
the merchantability of this software or the suitability of this
software for any particular purpose. It is provided "as is"
without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this
documentation and/or software.
----------------------------------------------------------------<<MT19937>>
The MT19937 software that Takuji Nishimura and Makoto Matsumoto developed
is contained, and this product shall be used subject to the following
license conditions.
Copyright (C) 1997 - 2002, Makoto Matsumoto and Takuji Nishimura,
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
90
Operating Instructions
Document Version 2012-06
Open Source Software
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. The names of its contributors may not be used to endorse or promote
products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
"AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
<<thttpd>>
The thttpd software that ACME Labs developed is contained, and this product
shall be used subject to the following license conditions.
Copyright 1995,1998,1999,2000 by Jef Poskanzer <jef@acme.com>.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
Document Version 2012-06
Operating Instructions
91
Index
Index
A
AC adaptor 12
Connection 63
Accessories 12
ACD flexible button 35
ACD Group 34
Add new device (setting) 50
Auto answer 27
AUTO ANSWER/MUTE button 15
Automatic Call Distribution ® ACD 34
B
Backlight (setting) 42
BLF flexible button 35
Bluetooth Headset 64
Bluetooth Headset (setting) 50
Busy Lamp Field ® BLF 35
20
E
ECO Mode (setting) 41
EHS headsets 64
EHS jack 16
Electronic Hook Switch ® EHS
Embedded web (setting) 47
Enable VLAN (setting) 47
ENTER key 15
Enter PIN (setting) 50
Error messages 84
Extension number 23
64
F
C
Call Block (setting) 49
Call Forwarding 34
Call Splitting 30
Call Transfer 30
Call Waiting 29
Calls
From call logs 26
From phonebook list 25
Holding 29
Making 25
Missed 33
Receiving 27
Redialing 26
Rejecting 27
CANCEL button 15
Character entry 51
Cleaning 76
CONF (Conference) button 15
CONFERENCE button 15
Conference call 32
Connect (setting) 50
Connections 63
Controls 13
Bottom view 17
Front View 13
Left view 16
D
Date and Time (setting) 44
DC jack 17
Default Gateway (setting) 46
Deregistration (setting) 50
Dialing 25
Directory Number ® DN 35
Disconnect (setting) 50
Display 14
Contrast 42
92
Display Lock (setting) 42
Display of Assigned Flexible Buttons
DN flexible button 35
DNS (setting) 46
DNS1 (setting) 46
DNS2 (setting) 46
Do Not Disturb 34
Do Not Disturb (setting) 43
Operating Instructions
Firmware version (setting) 48
FLASH/RECALL button 15
Flexible buttons 15, 35
FORWARD/DO NOT DISTURB button
Forwarding 34
FWD All (setting) 43
FWD Busy (setting) 43
FWD No Ans (setting) 43
15
G
Group, Login/Logout
34
H
Handset 12
Connections 66
Hooking 72
Volume 24
Handset cord 12
Handset hook 15
Handset jack 18
Hands-free mode 23
Headset 64
Flexible button 35
Using 74
Volume 24
HEADSET button 15
Headset jack 16
Hold 29
HOLD button 15
I
Information Display (setting)
Initialize 76
Installation 60
IP Address (setting) 46
IP Phone (setting) 47
45
Document Version 2012-06
Index
REDIAL button 15
Rejecting calls 27
Restart 76
Restart (setting) 48
Ring count (setting) 43
Ringer
Volume setting 24
Ringer (setting) 41
Ringer Volume (setting) 41
Ringer/Message Lamp 15
Ringtone (setting) 41
K
Key Click Tone (setting)
42
L
LAN connection 63
LAN port 18
LAN port (setting) 47
Language (setting) 44
Last Number Redial 26
LCD (Liquid Crystal Display) 14
LCD Contrast (setting) 42
LLDP-MED (setting) 46
Local Three-way Conference 32
Login (to a Group) 34
Logout (from a Group) 34
S
Scroll indicator 20
Search, phonebook list 25
Settings 38
Accessing 38
Setup 60
Initial settings 75
Soft buttons 15, 21
Icons 20, 21
Speaker
Volume 24
Speakerphone (SP-PHONE) button
Specifications 77
Speed/Duplex (setting) 47
SP-PHONE (Speakerphone) button
Stand 12
Adjusting 61
Attaching 60
Removing 61
Start-up menu 75
Status icons 19, 20
Subnet mask (setting) 46
M
Maintenance 76
Making calls 25
Calling 25
MESSAGE button 15
Message/Ringer Lamp 15
Messages, checking 33
MIC 15
Missed calls 33
MUTE/AUTO ANSWER button
15
N
Navigator key 15
Network (setting) 45
Network Test (setting)
48
O
Off-hook monitor 23
On/Off (setting) 46
One-touch Dialing 26
One-Touch flexible button
One-touch Transfer 30
15
15
T
Three-way conference 32
Timer (setting) 46
Transfer 30
TRANSFER button 15
Troubleshooting 80
35
P
Page keys 15
PC (setting) 47
PC connection 63
PC port 18
PC port (setting) 46, 47
Phonebook list
Adding 36
Deleting 37
Editing 36
Export 37
Import 37
Searching 25, 37
Priority (setting) 46, 47
Programming, web user interface
U
User settings
38
V
VLAN (setting) 46
VLAN ID (setting) 46, 47
Volume 24
W
59
Wall mount kit 12
Wall mounting 67
Web user interface programming
Wrap Up 35
59
R
Receiving calls
Redial 26
27
Document Version 2012-06
Operating Instructions
93
One screw here
WALL MOUNTING TEMPLATE
1. Drive the screws into the wall as indicated.
2. Hook the unit onto the screw heads.
/
/
100 mm (3 15 16 in)
83 mm (3 1 4 in)
Note:
Make sure to set the print size to
correspond with the size of this page. If the
dimensions of the paper output still deviate
slightly from the measurements indicated
here, use the measurements indicated
here.
One screw at either point
Notes
Document Version 2012-06
Operating Instructions
95
One Panasonic Way, Secaucus, New Jersey 07094
http://www.panasonic.com/sip
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
http://www.panasonic.ca
Copyright:
This material is copyrighted by Panasonic System Networks Co., Ltd., and may be reproduced for internal
use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic
System Networks Co., Ltd.
Panasonic System Networks Co., Ltd. 2011
PNQX3571UA DD0611MK5062
Open as PDF
Similar pages