Quick Start Guide - EcoTech Marine Asia

Quick Start Guide
MP40w ES
MP10 ES/ MP10w ES
This is the VorTech Quick Start Guide only.
For the full VorTech Pump manual, please visit our website at
www.ecotechmarine.com/cust-serv/downloads
• Read this manual before installing or using your Vortech Propeller pump.
• This manual guides you through safe and proper installation, operating procedures and
•
•
•
techniques.
All information contained in this manual is current at the time of printing.
Because EcoTech Marine, LLC, is commited to continuous product development, we
reserve the right to make product, design, and informational changes without notice.
For further instruction, additional, supplemental, or new information on advanced
functionality, troubleshooting and the service and maintenance of your pump please
visit EcoTech Marine’s website, located at www.ecotechmarine.com
This quick start guide is designed to get you started using your new VorTech Propeller Pump.
This is not intended to provide adequate information on the advanced features and modes of the
pump. For these features, please refer to our full instruction manual at www.ecotechmarine.com
Before You Start
Preparation
Once you have chosen the location where you want to install your VorTech pump, clean away any algae, using an
aquarium scraper. Use caution when handling an aquarium scraper.
Notes on placement
Take care to place the VorTech in a suitable location where corals are not directly in the line of flow. Place the
pump sufficiently high enough above a fine sand bed so that sand is not blown around by the output or undertow
created by the VorTech.
Protect the pump from water
The VorTech’s motor housing and driver are NOT WATERPROOF. Any water allowed into these components can
damage them enough to require replacement. This kind of damage is NOT covered in the VorTech’s warranty.
Protect these components from splashes, drips or other contact to water.
Break-in
The VorTech pump is engineered to adapt to its aqueous environment. During the first week of use, your pump
may run noisy or stall. The noise should subside after 24 hours of use and any stall condition can safely be reset
by manually cycling the power to your pump.
Warnings
•
•
•
•
•
•
The VorTech utilizes extremely powerful magnets and can cause severe personal injury.
NEVER connect the two halves of this device without proper spacer in-between.
NEVER place either half of this device near magnetically attractive surfaces or sensitive electronics.
The motor and driver can become HOT. Be cautious around these surfaces.
Never run the pump dry as the heat build up may cause damage to its components.
Do Not Drop Your VorTech Pump - The VorTech is highly engineered to be as powerful as possible. As a result the
VorTech is fragile. All precautions must be taken to avoid dropping the wet-side and dry-side components. After a
fall onto the floor, both the wet-side and dry-side can be permanently damaged. Evidence of this includes cracking of the advanced ceramic axle within the wet-side or the dry-side running loudly. The VorTech pump SHOULD
NEVER BE ALLOWED TO FALL to the floor. Damage from dropping will not be covered under warranty.
Maintenance
Cleaning Your VorTech
The VorTech may need thorough cleaning of the components periodically to keep it running optimally. This can
be accomplished by dissassembling the wet side of the pump and gently brushing the components with a soft
brush under running water. Soaking these parts in a mild acid solution such as vinegar may be necessary if there is
debris build up. Do not use strong acids as this may damage the components.
1
Your VorTech MP40w ES
Specifications and Operating Parameters
Flow: 1,000-3,200 gallons/hour (3,785-12,100 liters/hour)
Maximum Motor Temp: 122-140 degrees (50-60 degrees C)
Aquarium Wall Thickness: 3/16” to 3/4” (5mm to 19mm)
Power: 6-30 watts
Washer
O-Ring
Ceramic Bearing
Drive Shaft Nut
Nozzle
Wet -Frame
1.Push
To remove the nozzle from the wet-frame, remove the entire wethalf of the pump from the aquarium and place it on a non-metallic
surface. Gently but firmly press down on the nozzle with your palm
and twist counter-clockwise. The nozzle should become free of the
wet-frame. It may then be cleaned of any obstructions.
Adjust the Pin Spacer (MP40w ES Only)
Frame Cover
Plastic Coated Magnet
Drive Shaft
Propeller
Drive Shaft Screw
3.Remove
2.Twist
The VorTech pump is designed to operate with a constant gap between both
halves of the device. The pin spacer is used to ensure the proper spacing for
various aquarium wall thicknesses.
- Make sure to measure your aquarium’s glass thickness using a ruler or
contact the aquarium manufacturer in order to determine the exact thickness.
- To adjust the proper aquarium thickness, pull the rubber pin spacer from the
motor housing. Then align the VorTech’s power cord emerging from the motor
with your aquarium’s wall thickness to achieve the proper offset from your
aquarium.
NOTE: 3/4” (19mm) thick aquariums do not use the pin spacer at all.
IMPORTANT: When adjusting the pin spacer, be sure not to bend the rubber
pins as they are inserted into the holes within the heat sink as this may
permantly damage your VorTech. Bent pins WILL NOT be covered under
warranty.
For video tutorials, visit www.ecotechmarine.com/about/media-gallery
2
Attach the MP40w ES
Attach the motor assembly
• Apply the rubber gasket at the chosen location for the VorTech pump, on the
outside of your aquarium.
• Apply the cord mounting tab approximately 2” (50mm) above this location. Make
sure the glass is clean and free of any grease or dirt prior to applying this tab.
• Place the VorTech motor, with or without the pin spacer attached, upon the
black gasket, and secure the cord to the mounting tab using one of the provided
wire-ties.
• The cord must be positioned pointing upwards so that if the VorTech were to fall
off the aquarium, it does not swing and damage your aquarium or pump. When
operating, make sure the gasket is properly recessed within the pin spacer.
Attach the wetside assembly
• Place the wet side into the aquarium, making sure to allow ALL air to escape from
the propeller housing.
• Carefully connect both halves of the pump together and visually align both halves
of the pump.
Your VorTech MP10/MP10w ES
Specifications and Operating Parameters
Flow: 200-1575 gallons/hour (750 - 5,962 liters/hour)
Aquarium Wall Thickness: 1/8” to 3/8” (3mm to 10mm)
Power: 6-18 watts
Motor
Ceramic Washer
Nozzle
Rotor
O-Ring
To remove the nozzle from the wet frame, remove the entire wet
half of the pump from the aquarium and place it on a non-metallic
surface. Gently but firmly press down on the nozzle with your palm
and TWIST CLOCKWISE. The nozzle should become free of the wet
frame. It may then be cleaned of any obstructions. Be careful to
minimize force when twisting the wet frame.
Wet Frame
with Axle
1.Push
3.Remove
2.Twist
3
For video tutorials, visit www.ecotechmarine.com/about/media-gallery
Attach the MP10/MP10w ES
Attach the motor assembly
• Apply the cord mounting tab approximately 2” (50mm) above the desired location
of your VorTech pump. Make sure the glass is clean and free of any grease or dirt
prior to applying this tab.
• Place the VorTech motor upon the tank wall in your pre-determined location, and
secure the cord to the mounting tab using one of the provided wire-ties.
• The cord must be positioned pointing upwards so that if the VorTech were to fall
off the aquarium, it does not swing and damage your aquarium or your pump.
Attach the wet side assembly
• Place the wet side into the aquarium, making sure to allow ALL air to escape from
the propeller housing.
• Carefully connect both halves of the pump together and visually align both halves
of the pump.
IMPORTANT: For glass thicknesses of 1/8” (3mm) and 3/16” (5mm) you must use the
included rubber spacer in between the motor and the glass. There is no need to use
this spacer on glass thicknesses of 1/4” (6mm) or 3/8” (10mm). Failure to use the
included rubber spacer on glass thicknesses of 1/8” (3mm) and 3/16” (5mm) can damage your pump. Damage of this sort will not be covered under warranty.
Align Your Vortech Pump (All Versions)
• Turn the VorTech pump to constant speed mode (indicated by a green LED)
by pressing the mode button which is located on the driver, then set to the
maximum speed by using the speed control knob on the driver.
• Plug the power supply into the driver. If vibration or excessive noise is detected, carefully adjust the propeller housing by moving it VERY slightly left,
right, up or down, until the noise/vibration is eliminated or minimized as much
as possible.
• After alignment has been ensured, adjust to the mode of your choice and turn
the speed control knob to achieve the desired flow rate within your aquarium.
IMPORTANT: If the VorTech is not properly aligned, a strong vibration will be
heard. If the alignment is not corrected, this can cause increased electrical consumption, excessive wear on the components, excessive heat and excessive noise.
For video tutorials, visit www.ecotechmarine.com/about/media-gallery
4
Programming Multiple Pumps
NOTE: When using a single VorTech pump, no wireless configuration is necessary
A pump group consists of one master pump and at least one slave pump. There can only be one master pump per
group which can include an unlimited number of slave pumps. In order to set a pump as a master or a slave, the
aquarist must first enter the VorTech Pump’s configuration mode. Within configuration mode one can do one of
three different things:
• Reset the pump’s memory back to independent mode
• Set the pump as a master
• Set the pump as a slave
Masters and slaves must be set as groups and each group must be programmed separately. You must perform the
following steps in the order listed to correctly program your EcoSmart driver. You may setup a maximum of seven
separate groups, each having a unique master pump.
EcoSmart Pump Positioning
Master Pump
*Shown here in Constant Speed mode.
Sync/Anti-Sync Pump Setup
Can Operate in Constant Speed, Random,
EcoSmart, Short Pulse and Long Pulse Modes.
Slave Pumps (Orange, White, Turquoise)
White
Constant, Random, Short & Long Pulse modes: Sync
EcoSMART mode: Same side as master
EcoSmart Setup
Orange
Random, Short & Long Pulse modes: Anti-Sync
In EcoSMART mode: Opposite side as master
Back of Tank
Turquoise (EcoSmart only)
EcoSMART Mode: Back of the Tank
5
Detailed instructions and How To Videos on EcoSmart function available for
download at www.ecotechmarine.com/customer-service/how-to-videos
Assigning Master/Slave
hold
Step 1: Clear Driver Memory
The internal memory of each unit must be cleared before setting up
a group.
M
o de
+
hold
Set
o de
M
All pumps in a group must then be set into configuration mode before
the assignment of slave or master status. This configuration must
be performed with the drivers in close proximity to ensure proper
assignment. The drivers will blink red, white and blue in this mode.
Step 3: Assign the Master
Set the master pump by pressing the mode button. The LED will then
blink blue and green.
Step 4: Assign the Slaves
Set all the slave pumps by pressing the set button on each driver. The
LED will then blink blue and yellow.
NOTE: If any slave blinks blue and red, it was too far away from the
master driver and could not communicate properly.
Step 5: Complete Master/Slave Assignment
Hold the mode button on the master pump after completing ALL the
master/slave assignments. Your master pump will return to the mode
you were previously in and your slave pump will default to white
(sync). You have successfully completed assigning Master/Slave.
M
o de
+
Set
Pump
Resets
hold
Step 2: Enter Configuration Mode
hold
Set
tap
Mo
de
tap
Set
hold
Mo
de
Pump
Resets
Step 6: Toggle Slave pumps between Sync/Anti-Sync/EcoSmart
Press the mode button to toggle your slave pumps between Sync/Anti-Sync/EcoSmart slave modes.
Note: EcoSmart slave mode only available when Master Pump is in EcoSmart TSM or EcoSmart NTM modes.
Step 7: Begin Normal Operation
Use the controls on the Master Pump to operate all pumps in the group. Slave pumps can only be set to sync or antisync modes, or the three options in EcoSmart modes.
Step 8: Program Subsequent Groups
Now that the first group is programmed, repeat steps 1-5 on the next group of pumps, if so desired.
NOTE: The subsequent pump groups must be programmed near the original group. For example, if running
two different groups in separate areas of your house, the second group must be programmed within 5 feet
the first group to ensure proper communication.
Detailed instructions and How To Videos on assigning master and slave modes
available for download at www.ecotechmarine.com/customer-service/how-to-videos
6
General Operational Modes
Constant Speed Mode
When a pump is in Constant Speed Mode, the dial is used to set the operational speed. If this pump is a master, the associated slave pumps will replicate
the master whether in sync or anti-sync mode.
EcoSmart TSM (Tidal Swell Mode)
In this EcoSmart mode water is circulated to
create a harmonic balance in your aquarium reminiscent of the changing flow
conditions that would be found in nature. Over the course of several hours,
the flow pattern will go from very chaotic with an emphasis on left to right
flow direction to an emphasis on right to left flow direction, all the while
experiencing calm period in between and followed by a great surge of flow
at the very end of the cycle. Adjusting the dial changes the maximum speed
achieved at any time during this mode. Slave pumps should be positioned
opposite the master and on the back of the tank to take full advantage of the
EcoSmart modes.
EcoSmart NTM (Nutrient Transport Mode)
In this EcoSmart mode, water is circulated in a
two phase program consisting of wave motion to stir up detritus and surging
motion to move the detritus into your overflow where it can be skimmed out.
This effect promotes maximum health and nutrient export, as well as increased
growth for sensitive corals such as SPS. Adjusting the dial changes the maximum
speed achieved at any time during this mode. Slave pumps should be positioned
opposite the master and on the back of the tank to take full advantage of the
EcoSmart modes.
Random Mode
In random mode you can toggle between two
different modes, Reef-Crest and Lagoonal. When a pump is in Lagoonal Random
Mode, the dial is used to set the maximum operational speed, and the driver
will automatically randomize the pumps output to simulate either a high (ReefCrest) or low (Lagoonal) energy reef environment. If this pump is a master, the
associated slave pumps will replicate the master in sync or anti-sync modes.
Lagoonal
Reef Crest
Short Pulse Mode
When a pump is first entered into Pulse Mode, you must set the maximum
pump speed by adjusting the dial. When the desired speed is achieved, press the
Set button to lock this speed. The LED will now begin to ramp. This ramping LED
represents the pulsing frequency between 0.2 seconds and two seconds. Now
adjust the dial to make the pump pulse faster or slower. To save this wave, press
and hold Set until the LED flashes and then breathes blue, indicating that the
wave is saved. This saved wave will also be input into EcoSmart NTM.
Long Pulse Mode (Gyre Functionality)
When the pump is entered into Long Pulse Mode, the maximum speed of the
pump is set by adjusting the dial. When the desired speed is achieved, press
the Set button to lock this speed. The LED will now begin to ramp, the ramping
LED represents the pulsing frequency between 2 seconds and two hours. Now
adjust the dial to make the frequency increase or decrease. The first six LED lights
represent two seconds to two minutes. The seventh through twelfth LED lights
represent five minutes, ten minutes, 20 minutes, sixty minutes, ninety minutes
and two hours, respectively. To save this wave, press and hold the Set button until
the LED flashes and then breathes pink, indicating that the wave is saved. In this
mode the low pulse speed is the configured feed mode speed.
7
For further information on operational modes, download the full manual
available at www.ecotechmarine.com/customer-service/downloads
Feed Mode
To enter Feed Mode,
press and hold the mode
button for three seconds.
The LED will now blink
white indicating that the
pumps are in feed mode.
Regardless of your system’s
master/slave pump
configuration, all pumps will
enter feed mode when that
mode is selected on any one
pump. The pumps will spin
very slowly for ten minutes
and then resume their prior
operating conditions.
Constant
de
EcoSMART Driver General Operational Modes
EcoSMART *
Short Pulse
Random*
Speed
M
Set
Mo
Mo
Speed Set
Reef Crest
Speed Set
Set
Set
Set
Set
Short Pulse
Long Pulse
Freq. Set
*
Random*
NTM
Lagoon
Freq. Set
Set
Set
Set
Op
tio
/Pw n
r
de
(Hold) - Feed mode
Op
tio
/Pw n
r
(Hold) - Powers Off
Mo
Control Dial
Long Pulse
de
Mo
TSM
EcoSMART
ode
de
de
Mo
(Hold)
Set
Saved
Saved
Wave
Wave
(Hold)
*Note: LED bar will indicate change between modes
Battery Backup Mode
When a battery backup accessory is added to the VorTech pump, the pump will automatically switch to Battery Backup mode
during a power outage. The pumps will run at the minimum speed to maximize their run time during this critical period.
Wave Motion Warning
The generation of waves within your aquarium places additional stress on the aquarium glass and joints. Not all aquarium tanks are
designed to withstand this stress, and failure of the glass and/or joints could result. You are encouraged, before generating waves, to
consult with your aquarium tank manufacturer to determine if the tank construction is adequate to withstand the additional stress generated by the wave motion. You are also encouraged to assure that your aquarium stand or furniture is adequately stable to withstand the
additional stress resulting from wave generation.
EcoTech Marine DISCLAIMS AND WILL NOT BE LIABLE FOR, damage to aquarium tanks or their surroundings, water damage, or any other
consequential damages resulting from wave generation. MAKE WAVES AT YOUR OWN RISK.
Error Codes
Over Temperature Condition - In the event of a motor overheating, the pump will automatically shut down for a
period to allow for cooling. Once the motor has cooled, the driver will automatically restart and resume normal
operation. You may experience an overheating error from a misalignment.
Stall Condition - In the event of a motor stall, the pump may have stopped for a few possible reasons. You should
first check that there is not something blocking the propeller from spinning.
For further information on error codes, download the full manual
available at www.ecotechmarine.com/customer-service/downloads
8
Warranty
EcoTech Marine warrants to the original purchaser only that the VorTech propeller pump will be free from defects in material and
workmanship under normal use for a period of (1) year from the date of original purchase if the product is installed and used properly
and consistent with the User Manual. The VorTech propeller pump consists of a wet side operating unit that will be fully submerged in
the aquarium and a motor and driver that must not be exposed to water at any time. EcoTech Marine’s warranty shall not apply: (i) to
any damaged VorTech propeller pump that has been subjected to accident, misuse, neglect, alteration, acts of God, improper handling,
improper transport, improper storage, improper use or application, improper installation, improper testing or unauthorized repair, (ii)
to any VorTech propeller pump where the motor and/or driver have been exposed to water or (iii) to cosmetic problems or defects that
result from normal wear and tear under ordinary use, and do not affect the performance or use of the product. EcoTech Marine’s warranty applies only to a product that is manufactured by or for EcoTech Marine and identified by the EcoTech Marine trademark, trade
name or product identification logo affixed to the product. If you notice a problem with your VorTech propeller pump, do not attempt
to repair it yourself. Any attempts at self repair shall void this limited warranty. EcoTech Marine shall not be held liable for damage to
any aquarium, aquarium life forms, or other personal objects due to improper use of the device. If the product develops a covered defect within the one-year period, EcoTech Marine will, at its option, either repair or replace the VorTech propeller pump without charge,
provided that the VorTech propeller pump is returned during the warranty period.
The VorTech pump operates at high temperatures and produces forces within the aquarium that can cause extreme loading and
fatigue. Due to this, caution must be used when installing this device on any aquarium. Because the construction of aquariums varies
from each manufacturer and the operating conditions of each individual aquarist is different, there is a possibility that the VorTech
propeller pump may cause damage to your aquarium. Please contact your aquarium manufacturer to determine if your aquarium is
properly built and recommended for VorTech pumps. If you notice any damage to your aquarium, including but not limited to crazing,
cracking, bending, scratching, etc, immediately discontinue the use of the VorTech propeller pump. EcoTech Marine will not be liable
for any damage caused to your aquarium resulting from the use of the VorTech propeller pump.
To obtain warranty service or technical support, please contact EcoTech Marine’s customer service department at (610) 954-8480. You
will receive instructions on how to return the product for repair or replacement. To take advantage of this Limited Warranty you will be
required to supply an original point of purchase receipt.
ECOTECH MARINE DISCLAIMS ALL OTHER WARRANTIES WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED, TO THE FULLEST EXTENT
ALLOWED BY APPLICABLE LAW. NO IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY SHALL APPLY
EXCEPT AS REQUIRED BY APPLICABLE LAW. ECOTECH MARINE DOES NOT AUTHORIZE ANY PERSON OR BUSINESS ENTITY, INCLUDING
ITS AUTHORIZED DEALERS, TO CREATE FOR IT ANY OBLIGATIONS, LIABILITIES, OR OTHER WARRANTIES IN CONNECTION WITH THIS
PRODUCT.
ALL WARRANTIES ARE VOID IF THERE IS DAMAGE TO THE VORECH PROPELLER PUMP THAT IS NOT A RESULT OF A DEFECT IN THE
MATERIALS OR WORKMANSHIP. THE SOLE AND EXCLUSIVE REMEDY FOR ALL CLAIMS THAT YOU MAY HAVE ARISING OUT OF OR IN
CONNECTION WITH YOUR USE OF THIS PRODUCT, WHETHER MADE OR SUFFERED BY YOU OR ANOTHER PERSON AND WHETHER
BASED IN CONTRACT OR TORT, SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ECOTECH MARINE BE LIABLE
TO YOU OR ANY OTHER PARTY FOR ANY DIRECT, INDIRECT, GENERAL, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR OTHER
DAMAGES ARISING OUT OF THE USE OR INABILITY OF TO USE THE PRODUCT (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION OR ANY OTHER PECUNIARY LOSS, DAMAGE TO YOUR
AQUARIUM OR ANY AQUARIUM INHABITANTS), OR FROM ANY BREACH OF WARRANTY, EVEN IF ECOTECH MARINE HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. IN NO CASE SHALL ECOTECH MARINE’S LIABILITY EXCEED THE AMOUNT YOU PAID FOR THE
PRODUCT. IF YOU DISAGREE WITH THESE TERMS AND CONDITIONS DO NOT USE THE VORTECH PROPELLER PUMP.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusions may not apply to
you. EcoTech Marine’s warranty is governed by the laws of the Commonwealth of Pennsylvania, excluding its conflict of laws principles
and excluding the provisions of the United Nations Convention on Contracts for the International Sale of Goods. This warranty gives
you specific legal rights, and you may also have other rights, which vary from state to state.
9
FCC and CE Warnings
• This product carries an ingress protection rating of IPX0 and must not be
• To avoid injury, do not contact moving parts or hot parts such as heaters,
immersed in water.
reflectors, lamp bulbs, and the like.
• Danger: To avoid possible electrical shock, special care should be taken
• Always unplug an appliance from an outlet and battery backup when not in use,
since water is employed in the use of aquarium equipment. For each of the
before putting on or taking off parts, and before cleaning.
following situations, do not attempt repairs yourself; return the appliance to the • Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.
manufacturer for service or discard the appliance.
• Do not use an appliance for other than intended use. The use of attachments
• DO NOT immerse in water. If the appliance falls into the water, DON’T reach for not recommended or sold by the appliance manufacturer may cause an unsafe
it! First unplug it and then retrieve it. If electrical components of the appliance get condition.
wet, unplug the appliance immediately. (Non-immersible equipment only)
• Do not install or store the appliance where it will be exposed to weather or to
• Carefully examine the appliance after installation. It should not be plugged in if temperatures below freezing.
there is water on parts not intended to be wet.
• Make sure an appliance mounted on a tank is securely installed before operating
• Do not operate any appliance if it has a damaged cord or plug, or if it is
it. Read and observe all the important notices on the appliance.
malfunctioning or if it is dropped or damaged in any manner. The power cord of • If an extension cord is necessary, a cord with a proper rating should be used. A
this appliance cannot be replaced: If the cord is damaged, the appliance should be cord rated for less amperes or watts than the appliance rating may overheat. Care
discarded. Never cut the cord.
should be taken to arrange the cord so that it will not be tripped over or pulled.
• To avoid the possibility of the appliance plug or receptacle getting wet, position • Prior to servicing ensure the appliance is unplugged from the mains as well as
aquarium stand and tank to one side of a wall mounted receptacle to prevent
the battery backup.
water from dripping onto the receptacle or plug. The “drip-loop” should be
• The VorTech pump utilizes extremely powerful magnets and can cause severe
arranged by the user for each cord connecting an aquarium appliance to a
personal injury.
receptacle. A “drip-loop” is that part of the cord below the level of the receptacle, • NEVER place either half of this device near magnetically attractive surfaces or
or the connector if an extension cord is used, to prevent water travelling along the sensitive electronics.
cord and coming in contact with the receptacle. If the plug or receptacle does get • The motor and driver can become HOT. Be cautious around these surfaces.
wet, DON’T unplug the cord. Disconnect the fuse or circuit breaker that supplies • DO NOT stick fingers or anything else into the fan. Keep out of reach from young
power to the appliance, then unplug and examine for presence of water in the
children.
receptacle.
• NEVER run the pump dry as the heat build up may cause damage to its
• Close supervision is necessary when an appliance is used by or near children
components.
RF Module Important Information:
The product you have purchased contains the EcoTech Marine RF Module, part number 10169. This module gives your product
the ability to communicate wirelessly to other EcoTech Marine products as well as certain other manufacturer’s products that
were designed in compliance with the specifications for our RF Module. Use of this module in products not consented by
EcoTech Marine is prohibited. This product is for indoor usage only.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received including interference that may cause undesired
operation. Any changes or modifications not expressly approved by EcoTech Marine
could void the user’s authority to operate the RF module, and/or the product that
incorporates the RF Module. The user is cautioned to maintain a 20cm (8 inch) spacing
from the product to ensure compliance with FCC regulations.
European Union - Disposal Information:
This symbol means that according to local laws and regulations your product
should be disposed of separately from household waste. When this product
reaches its end of life, take it to a collection point designated by local authorities.
Some collection points accept products for free. The separate collection and
recycling of your product at the time of disposal will help conserve natural
resources and ensure that it is recycled in a manner that protects human health
and the environment.
This device contains:
EcoTech Marine’s RF Module
Part Number: 10169
FCC ID: VKB271829
IC: 7349A-271829
CE Declaration of Conformity
The equipment complies with the RF exposure Requirement 1999/5/EEC,
Council Reccomendation on the limitation of exposure of the general
public to electromagnetic fields (0-300 GHz). This equipment meets the
following conformance standards:
EN 300 328, EN 301 489-17
For France:
Français: Cet équipement est prévu uniquement pour un usage à
l’intérieur des bâtiments
English: This device is intended for indoor use only.
VorTech Pump can be used in the following countries:
AT
EE
IE
NL
ES
CH
BG
FI
IT
PL
SE
BE
FR
LV
PT
GB
CY
DE
LT
RO
IS
CZ
GR
LU
SK
LI
DK
HU
MT
SL
NO
10
Customer Support
United States & Canada
Contact manufacturer directly for all warranty service and returns.
www.ecotechmarine.com/customer-support
International
Contact your local distributor directly for all warranty service and returns.
www.ecotechmarine.com/where-to-buy/international-distributors
Contact Us
service@ecotechmarine.com
(610) 954-8480
toll free - (800) 785-0338
Open as PDF
Similar pages