GO-E2
HOPPER CAR GATE OPENER
The GO-E2 is an electric-powered Gate Opener with a rotating platform (for a full 360° swivel) on a rolling carriage
(to mount and slide along a secured-to-ground W-beam), utilizing pendant-controlled, instant Forward-Reverse
action, and a telescoping drive shaft with both vertical and horizontal adjustment (to follow traveling gate and
accommodate varied height capstans). The GO-E2 is well suited for worksites that experience: 1. Railcars that vary
from easy-to-open to moderately-difficult because they are well maintained and regularly repaired; 2. railcars with
either fixed position or traveling gate mechanisms; 3. limited or no compressed air supply; 4. railcars with varied
height capstan / gate mechanisms; 5. rough or uneven trackside terrain making Opener maneuverability an issue.
The GO-E2 uses a 5-HP motor to generate a constant
speed of 34-RPM and a power output of 2,000 ft-lbs
during surge and 875 ft-lbs during operation.
CAPSTAN DRIVE FITTING
TELESCOPING DRIVESHAFT
Telescopes 40” to 82” (longer lengths
Precision machined, 4140 tool steel, 1-piece
available) and angles 50° vertical and
step-tapered drive tip 1-1/4” x 1-1/2” sq
shank using HD set-screw retainer will last horizontal to accommodate both traveling
gate mechanisms and varied height gates.
through hundreds of gate openings.
PENDANT CONTROL MOTOR STARTER
Pushbutton control up to 20’ from
railcar gate enables instantaneous
forward/reverse jog of gear motor to
rock-open even stubborn gates.
ROTATING PLATFORM ON
ROLLING CARRIAGE
180° pivot enables opening
hopper car gates on parallel
tracks, and a 90° pivot enables
safe, out-of-the-way drive shaft
protection when not in use. The
Rolling Carriage locates and
locks-down the Opener directly
opposite every gate, anywhere
along the unloading site.
Master Distributor
284 Three Tun Rd Malvern, PA 19355-3981
Ph: 800.332.9770 Int: +1.215.333.5600
Fx: 888.964.3866 +1.215.331.9770
www.airmatic.com
Ph: 800.332.9770
Int: +1.215.333.5600
Fx: 888.964.3866
WMGOE2122015
www.workmaster.net
Ph: 866.476.9217
www.workmaster.net
284 Three Tun Rd
Malvern, PA 19355-3981
info@workmaster.net
GO-E2
HOPPER CAR GATE OPENER
SPECIFICATIONS
MODEL GO-E2 Beam Mounted Gate
Opener w/ Telescoping Drive
Shaft
POWER Electric; 230 / 460VAC / 60Hz
WORKING TORQUE 2000 ft-lb at 34 RPM
MOUNT ASSEMBLY Beam Mount: Fixed Position or
Rolling Carriage
DIMENSIONS Motor: 24”W x 26”L x 13”H; TDS*:
40” compressed to 82” extended
HEIGHT ADJUSTMENT TDS* Lift-on to accommodate
any Capstan height
1-WORKER POSITIONING & OPERATION
To enable greater productivity and reduced man-power
planning.
EASY-LIFT, MANUAL HEIGHT ADJUSTMENT
To easily compensate for differing height gates, or
variations in unloading site docks or platforms.
INVERTER DUTY 5-HP MOTOR
To provide low noise, low maintenance, and high
durability. Manufactured to AGMA Class 3 standards
allows 275% momentary overload capacity.
FINISH COATING Acrylic Enamel over
Polyurethane
INCLUDED (1) Drive Fitting; (1) Manual
GATE OPENER WEIGHT Motor: 150 lbs; TDS*: 68 lbs;
Control Package: 21 lbs
ECONOMICAL TO PURCHASE
To meet even the tightest budget when an electric
powered Gate Opener is required.
OPERATES AT 66dBA
SHIPPING WEIGHT 290 lbs
*TDS: Telescoping Drive Shaft
To accommodate noise restrictions at plant and
unloading site operations.
HEAVY DUTY, CUSTOM TELESCOPING DRIVE SHAFT
To meet the high torque, long life, and ease of
maintenance requirements of a Hopper Car Gate
Opener.
Master Distributor
284 Three Tun Rd Malvern, PA 19355-3981
Ph: 800.332.9770 Int: +1.215.333.5600
Fx: 888.964.3866 +1.215.331.9770
www.airmatic.com
The Workmaster® line of Hopper Car Unloading Products, from
our wide selection of gate openers and pneumatic pocket vibrators
to our pocket-to-undertrack-conveyor connectors, offers total
solutions to the vexing problems of unloading hopper cars.
Ph: 800.332.9770
284 Three Tun Rd
Int: +1.215.333.5600
Malvern, PA 19355-3981
Fx: 888.964.3866
WMGOE2122015
www.workmaster.net
info@workmaster.net
Open as PDF
Similar pages