RF CONCEPTS
Outdoor Day/Night Weather-proof
Quick Installation Guide
English
Français
Español
Deutsch
Português
Italiano
Türkçe
Polski
Русский
Česky
Svenska
IP7330
www.rfconcepts.co.uk
This guide describes the basic functions of IP7330.
All detailed
d t il d information
i f
ti is
i described
d
ib d in
i the
th user's
' manual.l
IP Sur veillance
English
RF CONCEPTS
Warning Before Install
Power off the Network Camera as
soon as it is found smoking or smelt
unusual.
Refer to your user’s manual for the
operating temperature.
Contact your distributor when
such cases happen.
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
when it’s lightening.
Do not insert any object into the
Network Camera, such as needles.
Do not drop the Network Camera.
www.rfconcepts.co.uk
EN-1
RF CONCEPTS
1
Package Contents
IP7330
Liquid tight connectors (3 holes, for
backup use)
Silica gel
Camera stand
Silica
gel
Power adapter
RJ45 female/female coupler
Quick installation guide /
Warranty card
Software CD
ST7501
Central Management Software
www.rfconcepts.co.uk
EN-2
English
RF CONCEPTS
2
Physical Description
Front panel
IR LED
Lens
Light sensor
Back panel
Status LED
Reset button
Connectors
General I/O terminal block
Ethernet 10/100 RJ45 plug
Power cord socket (black)
www.rfconcepts.co.uk
EN-3
RF CONCEPTS
3
Hardware Installation
1. Loose the liquid tight connectors, and then remove the rubber.
2. Loose the back cover.
3. Tear down the aluminum foil vacuum bag and take out the silica gel. Attach the
supplied silica gel to the inner side of the Network Camera. (Please replace the silica
gel with a new one if you open the back cover after installation.)
4. Make sure all cable lines are securely connected.
5. Tighten the back cover, rubber and liquid tight connectors.
6. Secure the Network Camera to the wall/ceiling by the supplied camera stand.
2
6
1
5
Wall mount
Ceiling mount
3
Silica
gel
Note
If you want to use your own cable lines, please loose two supplied screws and take out
the power board. Then be careful to make connections as the illustration below.
Power cord
Upper side
Terminal block (from left to right)
1: AV24V (red)
2: AC24V (red)
3: DI (white)
4: GND (black)
Ethernet cable
Screws
Bottom side
www.rfconcepts.co.uk
EN-4
English
RF CONCEPTS
4
Network Deployment
General Connection (without PoE)
1. If you have external devices such as
sensors and alarms, make connections
from general I/O terminal block.
AV24V
AC24V
DI
GND
AV24V: 24V+
AC24V: 24VDI
: Digital Input
GND : Ground
2. Use the supplied RJ45 female/female
coupler to connect the Network Camera
to a switch.
Use Category 5 Cross Cable when
Network Camera is directly connected to
PC.
POWER
LINK
COLLISION
1
2
3
4
5
RECEIVE
PARTITION
3. Connect the power cable from the
Network Camera to a power outlet.
www.rfconcepts.co.uk
EN-5
RF CONCEPTS
Power over Ethernet (PoE)
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data
via single Ethernet cable. See the following illustration to connect the Network
Camera to a PoE-enabled switch via Ethernet cable.
POWER
COLLISION
1
2
3
4
5
LINK
RECEIVE
PARTITION
PoE switch
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and
a non-PoE switch.
PoE power injector
(optional)
non-PoE switch
POWER
www.rfconcepts.co.uk
EN-6
COLLISION
1
2
3
4
5
LINK
RECEIVE
PARTITION
English
RF CONCEPTS
5 Assigning IP Address
1. Install the "Installation Wizard 2" under the Software Utility directory from software
CD.
2. The program will conduct analyses on your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
IW2
Installation
Wizard 2
3. The program will search the VIVOTEK Video Receivers, Video Servers or Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the bottom of your device to connect the Internet Explorer to the
Network Camera.
Network Camera
Model No: IP7330
RoHS
MAC:0002D1733012
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Pat. 6,930,709
Made in Taiwan
0002D1733012
www.rfconcepts.co.uk
EN-7
RF CONCEPTS
6
Ready to Use
1. Access to the Network Camera from the Internet.
2. Retrieve live video through web browsers or recording software.
For further setup, please refer to user’s manual on the software CD.
www.rfconcepts.co.uk
EN-8
RF CONCEPTS
Outdoor Day/Night Weather-proof
Quick Installation Guide
English
ᖅϛ
ᙏϛ
Рҏᇭ
Français
Español
Deutsch
Português
Italiano
Türkçe
Polski
Русский
Česky
Svenska
IP7330
www.rfconcepts.co.uk
This guide describes the basic functions of IP7330.
All d
detailed
t il d iinformation
f
ti iis d
described
ib d iin th
the user's
' manual.l
IP Sur veillance
Open as PDF
Similar pages