USER MANUAL

MCR-50

WWW.DENVER-ELECTRONICS.COM

Please read this user manual carefully before start using the product.

CLEANING THE CABINET

If the wooden cabinet becomes dusty please wipe it with a soft, non-abrasive dust cloth. Also don’t use water or spray cleaners as this can damage the cabinet and the plastic/metal parts of the unit.

TECHNICAL SPECIFICATION

 Turntable speed: 33/45/78 RPM (Disc size 17.5/25/30cm)

 CD can play CD/CD-R/CD-RW/MP3

 USB can play MP3

 Cassette: C60 & C90 (C120 cassette is not recommended)

 Output power: 2x2.5W

PREPARATION FOR USE

 Carefully remove the unit from the carton and remove all packing material from the unit.

 Unwind the AC power cord and extend it to its full length.

 Unwind the FM Antenna wire and extend to it to its full length.

 Raise the lid to expose the turntable. The turntable has been secured for shipment with a transit screw. Use a coin or a screwdriver to turn the transit screw clockwise. This will allow the turntable to “float”.

 Remove the opaque white plastic stylus cover from the phonograph stylus by sliding it in the direction of the arrow.

 Please pay attention to the stylus during operation because stylus damage is not covered by the warranty.

 Remove the the twist-tie that was used to secure the tone arm during shipment.

 Release the tone arm lock lever.

 Connect the power plug to your AC 220V, 50HZ outlet.

IMPORTANT: RAISING AN LOWERING THE TURNTABLE LID

To open the lid. Raise it as far as it can go until the lid support bracket locks in the position.

To close the lid. Pull forward the lid support bracket to release and then gently lower the lid.

TO AVOID DAMAGING THE CABINET OR THE LID, NEVER FORCE THE LID CLOSED. ALWAYS RAISE

THE LID TO RELEASE THE LID SUPPORT BRACKET.

LOCATIONS OF CONTROLS AND INDICATORS

1. TURNTABLE LID

2. TURNTABLE LID SUPPORT BRACKET

3. SPEAKERS

4. USB

5. POWER BUTTON

6. RECORD BUTTON

7. FUNCTION BUTTON

8. VOLUME CONTROL

9. TUNER BACKLIGHT

10. LCD DISPLAY

11. REMOTE CONTROL SENSOR

12. POWER INDICATOR

13. FM ST./REC INDICATOR

14. FM DIAL SCALE

15. AM DIAL SCALE

16. TUNING POINTER

17. AM BUTTON (MW)

18. FM BUTON (UKW)

19. CD/USB BUTTON

20. TAPE BUTTON

21. PHONO/AUX IN BUTTON

22. CD DRAWER

23. TUNING CONTROL

24. PLAY/PAUSE BUTTON ( )

25. STOP BUTTON ( )

26. DN/F.R BUTTON ( )

27. UP/F.F BUTTON ( )

28. PLAY MODE BUTTON ( )

29. OP/CL BUTTON ( )

(CD OPEN/CLOSE BUTTON)

30. CASSETTE EJ/F.F BUTTON

(EJECT/FAST FORWARD)

31. CASSETTE PLAYER SLOT

32. TRACK+10

33. TRACK-10

34. DELETE

35. REPEAT

36. DN/FB (Skip Reverse)

37. UP/FF (Skip Forward)

38. RANDOM

39. PROGRAM

Note 1: All buttons on the remote control have the same function as the buttons on the unit. Thie remote control is just used for CD/MP3 and USB mode.

Note 2: Long pressing PLAY/PAUSE on remote control for 2 seconds will change between CD and

USB.

Note 3: Long pressing DELETE on remote control for 2 seconds will delete file in USB mode.

40. FM antenna

41. AC power cord

42. LINE OUT (L/R)

43. AUX IN

INFORMATION

The AM antenna is inside the cabinet. IF AM reception is unsatisfactory try repositioning the cabinet slightly until the internal antenna is picking up the strongest signal.

The FM wire is located back of the cabinet. If necessary adjust the position and direction of this antenna until you find the position that provides the best reception.

44. Turntable

45. 45 rpm adapter

46. Cue lever

47. Auto Stop control

48. Speed selctor (33/45/78 rpm)

49. Tone arm lock

50. Tone arm with stylus

POWER ON/OFF

1. Press POWER to turn the system on. The power indicator lights up.

2. Press the function selector buttons (AM/FM/CD/USB/TAPE/PHONO/AUX IN) to select the desired function.

3. Start to adjust the volume by using the volume control button.

4. When finished listening press POWER again to turn off the system. The power indicator goes off.

RADIO OPERATION

1. Press POWER to turn the system on.

2. Make sure you connected the FM antenna cable on the rear side of the unit.

3. Press MW button for AM or UKW button for FM radio.

4. Rotate the TUNING control to tune the desired radio station, the FM ST/REC indicator will light.

CD OPERATION

1. Press the CD/USB button to enter CD mode, the “---“ and ‘DISC’ icon will be shown on the screen. The unit can play CD, CD-R and CD-RW.

2. Press the OP/CL button top open the CD drawer.

3. Place your disc in the CD drawer with the label side facing up.

4. Press the OP/CL button again to close the CD drawer. Playback will automatically start from the first track.

5. MP3 icon will be shown if MP3 file is detected in the disc.

PLAYING CASSETTE

Note: Before inserting the tape in the player be sure that there is no excess slack in the cassette that could jam the mechanism.

1. Press POWER to turn the system on.

2. Press TAPE button to enter TAPE mode.

3. Insert your cassette into the slot loacated on the right side of the cabinet, as shown in the illustration, with the side you wish to play facing up and the open end on the right side.

4. Cassette playback begins as soon as the tape is inserted. Adjust the VOLUME control to the desired level.

5. To advance the tape rapidly, depress the button approximately half way. The tape will move forward rapidly as long as the button is depressed. Normal playback will resume when the button is released.

6. When the tape ends, the player stops automatically. Depress the button completely to remove the tape from the player. You may depress button to stop playing the tape at any time.

7. Press POWER again to turn the system off.

PLAYING VINYLS RECORDS

The system includes a full-size, 3 speed, belt-drive turntable. You can play 33, 45 and 78rpm records.

1. Press POWER to turn the system on.

2. Press the PHONO button to enter the PHONO mode.

3. Make sure you have removed the stylus cover from the stylus and have released the tone arm lock that secured the tone arm to the tone arm rest.

4. Set the turntable speed selector to appropriate speed 33, 45 or 78rpm. If you are playing

45 rpm singles, place the 45rpm adapter on the centre spindle.

5. Place your record on the the centre spindle.

6. Raise the cue lever to lift the tone arm of its rest. Move the tone arm to the edge of the record. The turntable starts automatically. Use the cue lever to gently lower the tone arm onto the record.

7. Adjust the volume control to the desired level.

8. When the tone arm reaches the end of the record it automatically returns to the tone arm rest and the record player stops.

9. Press POWER again to turn the system off. The POWER indicator goes OFF.

Note: Do not turn or stop the turntable manually. Moving or jarring the turntable without securing the tone arm clamp could result in damage to the tone arm.

AUX IN OPERATION

Conenct the audio system into the AUX IN jack on the rear panel, Press the PHONO/AUX IN button. Start playing from the connected device.

USB OPERATION

1. Press the CD/USB button first and the FUNCTION button to enter USB mode. The ‘---‘ and

USB icon will be shown.

2. Insert a USB flash device into the USB socket.

3. PLAY/PAUSE, DN/UP and stop functions are the same as CD functions.

Note: You may press the FUNCTION on the panel or long press PLAY/PAUSE button on the remote control for 2 seconds to change the playing mode between CD and USB.

PLAYING IN MP3 MODE (CD/USB)

1. Press PLAY/PAUSE button to start or pause playback selected track.

2. While playing the song, the song number and folder number of the slected track will be shown in the display.

3. You can stop the playback at any time by pressing the STOP button.

TRACK SKIP AND HIGH SPEED TRACK SEARCH IN CD/USB MODE

During CD/USB playback press UP/F.F ( ) or DN/F.R ( ) button on the unit front panel or on the remote control repeatedly to change track. To rapidly search forward or backwards within a track press and hold UP/F.F ( ) or DN/F.R ( ) button. To skip 10 tracks back or forth then press

TRACK-10 or TRACK+10 on the remote control.

USB RECORDING

1. CD recording

Insert USB flash drive into the USB socket. Then press CD/USB button. Place CD into the CD drawer and play the track which will be recorded. Press RECORD button twice to start recording. If all CD is played, Then all tracks will be recorded.

NOTE: Recording will fail if pressing STOP button during recording

2. MP3 DISC recording

Insert USB flash drive into the USB socket. Then press CD/USB button. Place CD with MP3 files into the CD drawer and play the MP3 track which will be recorded. Press RECORD button twice to start recording. If all MP3 files is played, Then all tracks will be recorded.

NOTE: Recording will fail if pressing STOP button during recording

3. Cassette recording

Insert USB flash drive into the USB socket. Then press TAPE button. Place the cassette into the socket. Play cassette. Press RECORD button twice to start recording. Press STOP button to stop recording.

4. Vinyl recording

Insert USB flash drive into the USB socket. Then press PHONO/AUX IN button. Play the vinyl and press RECORD button twice to start recording. Press STOP button to stop recording.

5. AUX IN recording

Insert USB flash drive into the USB socket. Connect the external audio device into the AUX jack on the rear panel. Then press PHONO/AUX IN button and play audio and press

RECORD button twice to start recording.

DELETE TRACKS FROM USB DISC

Press CD/USB button on the front panel or long press PLAY/PAUSE on remote control to select USB mode. Select the track and press delete for 2 seconds and the track is deleted.

ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S

Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and the environment, if the waste material

(discarded electric and electronic equipment and batteries) is not handled correctly.

Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen below. This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other household waste, but should be disposed of separately.

As the end user it is important that you submit your used batteries to the approriate and designated facility. In this manner you make sure that the batteries are recycled in accordance with legislature and will not harm the environment.

All cities have established collection points, where electric and electronic equipment and batteries can either be submitted free of charge at recycling stations and other collection sites, or be collected from the households. Additional information is available at the technical department of your city.

Imported by:

DENVER ELECTRONICS A/S

Stavneagervej 22

DK-8250 Egaa

Denmark www.facebook.com/denverelectronics