HP
JetDirect
Print Servers
HP JetDirect
External Print
Servers
300X, 500X, 170X, EX Plus
Hardware Installation
Guide
Hardware Installation Guide
HP JetDirect External
Print Servers
©Copyright
Hewlett-Packard Company 1999.
All rights reserved.
For warranty service information, see
appendix C at the back of this manual.
Reproduction, adaptation or
translation without prior written
permission is prohibited, except as
allowed under the copyright laws.
Publication number 5969-3466
Hewlett-Packard has support services
available to help you in case of
difficulties with your HP JetDirect
300X, 500X, 170X, and EX Plus external
print servers.
August 1999
Safety Considerations
Applicable Products:
Prior to the installation and use of this
product, review all safety markings and
instructions.
HP J2591A, HP J3258B,
HP J3263A, HP J3264A, HP J3265A
Trademark Credits
®,
MS-DOS®,
Windows™,
Microsoft
Microsoft Windows NT™ are
trademarks or U.S. registered
trademarks of Microsoft Corporation.
Novell® and NetWare® are registered
trademarks of Novell Corporation. IBM
LAN Server® is a registered trademark
of International Business Machines
Corp. Ethernet is a registered
trademark of Xerox Corporation.
PostScript™ is a trademark of Adobe
Systems, Incorporated, which may be
registered in certain jurisdictions.
UNIX® is a registered trademark in the
United States and other countries,
licensed exclusively through X/Open
Company Limited.
Warranty
The information contained in this
document is subject to change without
notice.
HEWLETT-PACKARD COMPANY
MAKES NO WARRANTY OF ANY
KIND WITH REGARD TO THIS
MATERIAL, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED
WARRANTIES OF
MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
Hewlett-Packard shall not be liable for
errors contained herein or for incidental
or consequential damages in connection
with the furnishing, performance or use
of this material.
A copy of the specific warranty terms
applicable to your HP product and
replacement parts can be obtained from
your HP Sales and Service Office or
Authorized dealer.
Customer Support
!
Instruction Manual
Symbol. If the product
is marked with this
symbol, refer to the
product manuals to
protect the product from
damage.
WARNING
Denotes a hazard that
can cause injury.
CAUTION
Denotes a hazard that
can damage equipment
or data.
Do not proceed beyond a WARNING or
CAUTION notice until you have
understood the hazard and have taken
appropriate steps.
Servicing. Any service, adjustment,
maintenance, or repair of this product
must be performed only by authorized
service-trained personnel.
Power. These products do not have a
power switch; they are powered on
when either the power cord or AC
adapter is plugged into a power outlet.
The power outlet shall be installed near
the equipment and shall be easily
accessible for quick disconnect.
Hewlett-Packard Company
8000 Foothills Boulevard
Roseville, California
95747-6588
Contents
1 Product Overview
Supported Printers, Plotters, and HP All-in-One
Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Network Management . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Network Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Components and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Transmission Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Switches (HP JetDirect 300X and 500X). . . . . . . . . . . . . . . . 1-9
2 Hardware Installation
Verifying the Hardware Installation . . . . . . . . . . . . . . . . . . . 2-3
Selecting a Configuration Page Language . . . . . . . . . . . . 2-3
Resetting to Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . 2-4
A Specifications
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Acoustic Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Electromagnetic Emissions . . . . . . . . . . . . . . . . . . . . . . A-4
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
B Regulatory Statements
FCC Statement (U.S.A) . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . B-2
3
4
1
Product Overview
This hardware guide covers the following Hewlett-Packard print
servers:
Three-Port Print Servers
One-Port Print Servers
HP JetDirect 500X
J3265A
HP JetDirect 170X
J3258B
HP JetDirect 500X
J3264A
HP JetDirect EX Plus
J2591A
HP JetDirect 300X
J3263A
These print servers send data to printers at speeds of up to
360 kilobytes per second, which is as fast or faster than many
internal print servers. The external print servers enhance
workgroup capability by letting you place your printers, plotters, or
HP All-in-One peripherals1 at convenient locations directly on the
network, and by increasing network printer performance and
management.
The one-port print servers connect one printer, plotter, or
All-in-One peripheral with a parallel port to the network. These
print servers have one high-speed, bidirectional parallel port
(IEEE 1284 standard) that supports multiple network operating
systems (NOSs) (Figure 1.1).
Figure 1.1 Use an HP JetDirect 300X, 170X, or EX Plus external print
server to connect one peripheral to your network.
1.The scanning functionality of HP All-in-One peripherals is not
supported by J2591A.
1-1
The HP JetDirect 300X provides connectivity to 10Base-T and
100Base-TX networks. The HP JetDirect 170X provides
connectivity to 10Base-T networks. The HP JetDirect EX Plus
provides connectivity to 10Base-T and 10Base2 networks.
The HP JetDirect three-port print servers have three high-speed,
bidirectional parallel ports (IEEE 1284) that support multiple
network operating systems (NOSs). Each port operates
independently which, in effect, gives you three print servers in one
(Figure 1.2).
Figure 1.2 Use the HP JetDirect 500X print server to connect up to three
peripherals to your network.
There are two models of the HP JetDirect 500X: one for 10Base-T,
100Base-TX, and 10Base2 networks (J3265A) and the other for
Token Ring networks (J3264A). The 500X connects up to three
printers, plotters, or HP All-in-One peripherals with parallel ports
to a network.
Supported Printers, Plotters, and HP All-in-One Peripherals
The HP JetDirect external print servers support almost any
printers1, plotters, or HP All-in-One peripherals2 with a parallel
port, including those made by HP and other companies. To connect
a serial printer, use a parallel-to-serial adapter.
1. GDI printers are not supported by HP JetDirect print servers.
2. J3263A, J3264A, J3265A, and J3258B support the following
HP All-in-One peripherals: HP LaserJet 1100A, the
HP OfficeJetPro Series, and the OfficeJet R40 and R60.
1-2 Product Overview
Network Management
Peripherals connected to an HP JetDirect external print server
appear as intelligent nodes on the network and are accessible
through various diagnostic utilities using the SNMP/IPX and
SNMP/IP protocols. These print servers also collect network
statistics and error messages to aid in network management and
troubleshooting.
Network Configuration
The HP JetDirect 300X, 170X, and 500X print servers provide an
embedded web server that can be accessed through a supported web
browser. For more information, see the Quick Start Guide (hardcopy
manual) shipped with your print server or the HP JetDirect
Administrator’s Guide shipped on the HP JetDirect CD-ROM with
your print server.
Product Overview 1-3
1 Product Overview
The HP JetDirect external print servers support the Simple
Network Management Protocol (SNMP), which enables remote
printer management and troubleshooting. A standard SNMP agent
resides on these print servers. Any standard SNMP-based
application can be used to access and manage these print servers.
Eh1ovw.fm Page 4 Wednesday, July 7, 1999 6:59 PM
Components and Features
HP JetDirect 300X (J3263A):
●
Bidirectional parallel port (IEEE 1284).
●
Network port (Ethernet or Fast Ethernet): RJ-45 for 10Base-T
or 100Base-TX.
●
Test button (sends print server configuration page).
●
2 LEDs on front indicate LAN activity/status.
●
2 LEDs on back indicate 10 or 100 Mbps.
HP JetDirect EX Plus (J2591A):
●
Bidirectional parallel port (IEEE 1284).
●
Network port (Ethernet): RJ-45 (10Base-T) or BNC
(10Base2).
●
Test button (sends print server configuration page).
●
2 LEDs on front indicate LAN activity/status.
HP JetDirect 170X (J3258B):
●
Bidirectional parallel port (IEEE 1284).
●
Network port (Ethernet): RJ-45 (10Base-T).
●
Test button (sends print server configuration page).
●
2 LEDs on front indicate LAN activity/status.
HP JetDirect 500X (J3265A, J3264A):
●
3 bidirectional parallel ports (IEEE 1284).
●
Network port:
J3265A (Ethernet): RJ-45 (10Base-T, 100Base-TX) and
BNC (10Base2).
J3264A (Token Ring): DB9 (shielded twisted-pair) and
RJ-45 (unshielded twisted-pair).
●
Test button (sends print server configuration page to Port 1).
●
2 LEDs on front indicate LAN activity/status.
●
J3265A: 2 LEDs on back indicate 10 or 100 Mbps.
●
J3264A: switch for 4 or 16 Mbps.
HP JetDirect Quick Start Guide:
Included with every external print server. Explains how to install
the print server and configure it for Novell or Microsoft NOSs.
(For other NOSs, refer to the user manuals on the HP JetDirect
CD-ROM.)
Power Module:
Included with every external print server: Provides power to the
HP JetDirect external print servers.
1-4 Product Overview
Included with every external print server: Contains software for
configuring the print server for network printing, online software
and hardware manuals, and product literature. (The software
on the CD is the most current at the time of release; to see if
there is a later version, check http://www.hp.com/cposupport/.)
Product Overview 1-5
1 Product Overview
HP JetDirect CD-ROM:
Transmission Media
IEEE 802.3
Ethernet
10Base2
Thin coaxial cable with BNC connector.
IEEE 802.3
Ethernet
10Base-T
Four pairs of unshielded twisted-pair
Category 3, 4, or 5 cable with RJ-45
connector.*
IEEE 802.3
100Base-TX
Fast Ethernet
Four pairs of unshielded twisted-pair
Category 5 cable with RJ-45 connector
for 10 or 100 Mbps operation.
IEEE 802.5
Token Ring
Shielded twisted-pair cable with 9-pin D-connector
(operating at 4 Mbps or 16 Mbps).
IEEE 802.5
Token Ring
Four pairs of unshielded twisted-pair cable with RJ-45 connector (operating at 4 Mbps or 16 Mbps).
*For 10Base-T, the print server works only with a 10Base-T LAN hub or
concentrator that supports link beat (link test pulse) signals.
1-6 Product Overview
HP JetDirect 300X
J3263A (Ethernet 10Base-T or 100Base-TX)
HP JetDirect 170X
J3258B (Ethernet 10Base-T)
HP JetDirect EX Plus
J2591A (Ethernet 10Base-T or 10Base2)
HP JetDirect 500X
J3265A (Ethernet 10Base-T, 100Base-TX, or
10Base2)
J3264A (Token Ring): DB9 (shielded twistedpair) or RJ-45 (unshielded twisted-pair)
Printer, plotter, or
HP All-in-One
peripheral
Bidirectional parallel port (IEEE 1284)
Recommended HP
cables and part
numbers
2 meter A-to-B parallel cable (C2950A)
(or parallel-to-serial adapter for serial ports)
3 meter A-to-B parallel cable (C2951A)
3 meter A-to-C parallel cable (C2946A)
10 meter A-to-C parallel cable (C2947A)
Power Module
(Included)
See Appendix A for the power module for your
country
Product Overview 1-7
1 Product Overview
Hardware Requirements
LEDs
On the top of the print server are Status and LAN Activity LEDs:
If the
Status
LED is...
And the
Activity
LED is...
Then the print server is...
Off
Off
Not receiving power.
On
Off
On; no LAN activity detected.
On
Blinking
On; LAN activity detected.
Off
On (Solid)
Encountering a fault during self-test or
operation.
Blinking
Off
Encountering one of the following conditions:
●
●
●
On
On
running a self-test
not configured.
not able to attach to the network.
On; heavy LAN activity detected.
Between the Status and LAN Activity LEDs is the Test button, used
to print a configuration page. See Chapter 2 for more information.
On the back of the HP JetDirect 300X (J3263A) and 500X (J3265A)
Print Servers, there are LEDs that indicate the operating speed
(10 Mbps or 100 Mbps) (Figure 1.3). (This applies to 10Base-T and
100Base-TX networks only.)
If the
10 (left)
LED is...
And the
100 (right)
LED is...
Off
Off
No link established.
On
Off
Link established at 10 Mbps.
Off
On
Link established at 100 Mbps.
Auto-negotiation
Switches
Then the print server has...
10 & 100
LEDs
Figure 1.3 Back of HP JetDirect 300X Print Server. (For the HP JetDirect
500X, the LEDs are also located next to the RJ-45 port.)
1-8 Product Overview
The HP JetDirect 300Xand 500X Print Servers have configuration
switches that should be used only if the print server fails to link on
the network. The factory-default setting of all 3 switches down will
suit most installations. These switches only apply to 10Base-T and
100Base-TX networks only.
When the first switch is set to Auto, the other two switch settings
are ignored; the server auto-negotiates the link speed and duplex
setting with the connected switch or hub device. Even with devices
that don’t auto-negotiate, the print server detects the network link
speed and uses half duplex.
Although nearly always unnecessary, you can control the settings
directly by positioning the switches as shown in the table below,
only if you are certain of the duplex setting and speed at which the
switch or hub is operating.
If the auto
switch is
set to...
And if the
speed switch
is set to...
And if the
duplex switch
is set to...
Then the
settings are...
AUTO
(down)
either position
(default=down)
either position
(default=down)
Auto-negotiated
(factory default)
MANUAL
(up)
10 (up)
HALF (down)
10Base-T
Half-duplex
MANUAL
(up)
100 (down)
HALF (down)
100Base-TX
Half-duplex
MANUAL
(up)
10 (up)
FULL (up)
10Base-T
Full-duplex
MANUAL
(up)
100 (down)
FULL (up)
100Base-TX
Full-duplex
Note
In Auto mode, you can see the network speed being
used by checking the LEDs at the RJ-45 connector.
See p.1-8.
Product Overview 1-9
1 Product Overview
Switches (HP JetDirect 300X
and 500X)
1-10 Product Overview
2
Hardware Installation
To install the HP JetDirect external print servers, you need to
complete these steps.
●
●
●
Verify that your printer parallel port(s) work properly.
Connect the print server to the network and printer(s) and plug
in the print server.
Generate a configuration page from the print server.
After you install the print server, the next step will be to configure
it. For information about configuring, refer to either the Quick Start
Guide shipped with your print server (for Novell or Microsoft NOSs)
or to the HP JetDirect Software Installation Guide on your
HP JetDirect CD-ROM.
Follow these instructions to install the HP JetDirect external print
servers. (“Printer” refers to any peripheral you are connecting to the
print server.)
1. To ensure your printer(s) work properly, do one of the following:
■
send data through the parallel port of each printer you are
connecting to the print server, or
■
generate a printer self-test page (refer to your printer manual
for instructions).
2. Switch off the power for each printer.
3. For a Token Ring print server (J3264A), set the data-rate switch
to the appropriate speed (4 Mbps or 16 Mbps) (Figure 2.1). To do
this, take a pen or similar object and slide the switch up for
16 Mbps or down for 4 Mbps.
Data-rate switch
Figure 2.1 Token Ring data-rate switch set at 16 Mpbs on the J3264A
2-1
4. For the 300X or 500X Ethernet print servers (J3263A or
J3265A), verify that the auto-negotiation switches are in their
default positions—all down. (For other options, see page 1-9.)
Figure 2.2 Hardware connections using a U.S. power module for the
HP JetDirect J3265A Print Server
Note
In the following steps, the circled numbers
correspond to those in Figure 2.2. The HP JetDirect
300X, 170X, and EX Plus have one printer port ➌.
The HP JetDirect 500X Token Ring and 300X have
no BNC port ➊. On the HP JetDirect 500X and
300X, the RJ-45 connector ➋ is used for either 10 or
100 Mbps operation. The JetDirect 170X has no
BNC port ➊.
5. Connect the print server to the network ➊ or ➋.
6. Connect the print server to the printer(s) ➌, ➍, and ➎.
If you are attaching only one printer to the 500X, HP
recommends that you attach that printer to Port 1 ➌.
If you are using DLC/LLC network protocols, your printer must
be connected to Port 1 (the DLC/LLC protocol is supported only
on Port 1).
7. Plug the power module into the power receptacle in the back of
the print server ➏.
2-2 Hardware Installation
8. Plug the power module into the wall outlet ➐. Since there is no
power switch, the print server is switched on after you plug it in.
9. Check the LEDs on the front of print server. The Status LED
should be green—either steady or blinking.
If the internal self-test failed, the Activity LED will be on and
the Status LED will be off. For troubleshooting information, see
the Troubleshooting chapter in the software guide shipped with
your print server.
11. Switch on the power on your printer(s) to begin printing.
Verifying the Hardware Installation
To verify the installation of the HP JetDirect external printer
server, generate a configuration page. This page is generated from
Port 1 of the printer server.
To generate a configuration page, follow these steps:
1. Print a configuration page by pressing and releasing the Test
button on the print server.
2. If the configuration page displays the message I/O CARD
READY, you have successfully completed the hardware
installation. (If not, see the Troubleshooting chapter in the
HP JetDirect Print Server Administrator’s Guide shipped on the
HP JetDirect CD-ROM.)
Refer to this configuration page when you are configuring the
software. For sample configuration pages, see the
Troubleshooting chapter in the HP JetDirect Print Server
Administrator’s Guide shipped on the HP JetDirect CD-ROM.
Selecting a Configuration Page Language
The configuration page for the HP JetDirect external print server
is sent to the printer attached to Port 1. The printer language is
auto-detected the first time the print server is powered up and after
each cold reset.
Hardware Installation 2-3
Hardware
2 Installation
10. Wait about 10 seconds. For 10Base-T and 100Base-TX networks,
check the 10 and 100 LEDs on the back to verify that the correct
one is lit. See p.1-8.
If you want to change the detected printer language, use the LEDs
and Test button to select a PDL for the configuration page. When
you hold down the Test button for three seconds, the LEDs begin to
cycle through four configurations, as outlined in the following table.
Release the Test button when you get the right PDLs, and the
configuration page will be printed.
For PDL...
The Status
LED is...
And the Activity
LED is...
HP PCL (default)
Off
Off
ASCII
Off
On
Postscript
On
Off
HP-GL/2
On
On
When you first press the Test button, the Status and Activity LEDs
are on and solid for about 3-4 seconds. Then they switch off,
indicating they are cycling through the PDLs.
Resetting to Factory Defaults
Once you have configured the HP JetDirect external print server,
the configuration settings are retained in memory unless you
manually reset them.
(The firmware is not affected when you reset the configuration
settings.)
To reset the configuration settings to their factory defaults, follow
these steps:
1. Unplug the power cord from the print server.
2. While holding down the Test button on the print server, plug the
power module into the print server and continue to hold down
the Test button for five seconds. All previous configuration
settings will be erased.
2-4 Hardware Installation
A
Specifications
Physical Specifications
Product
Number
Width
Height
Depth*
Weight
J2591A
178 mm
(7.0 in.)
31 mm
(1.2 in.)
124 mm
(4.9 in.)
269 g
(0.59 lbs.)
J3263A
178 mm
(7.0 in.)
31 mm
(1.2 in.)
112 mm
(4.4 in.)
241 g
(0.53 lbs.)
J3264A
280 mm
(11 in.)
31 mm
(1.2 in.)
127 mm
(5.0 in.)
454 g
(1 lb.)
J3265A
280 mm
(11 in.)
31 mm
(1.2 in.)
141 mm
(5.6 in.)
440 g
(0.97 lbs.)
J3258B
180 mm
(7.09 in.)
33 mm
(1.3 in.)
115 mm
(4.53 in.)
224 g
(0.49 lbs.)
*Measurement includes any protrusions for connectors, legs, etc.
A-1
Power Requirements
Power Modules for J3264A and J3265A
Note: If two parts are listed for one country/region, either part can be used.
Country
Part Num.
Input Rating
Output Rating
Australia, New
Zealand, Argentina
9100-5172
230-240VAC
50 Hz
13 VDC @625 ma
0950-3358
230-240VAC
50 Hz
13 VDC @800 ma
0950-2808
230-240VAC
50 Hz
13 VDC @625 ma
0950-3347
230-240VAC
50 Hz
13 VDC @800 ma
9100-5166
220-240V
50 Hz
13 VDC @625 ma
0950-3349
220-240V
50 Hz
13 VDC @800 ma
9100-5169
90-110V
50/60 Hz
13 VDC @625 ma
0950-3352
90-110V
50/60 Hz
13 VDC @800 ma
9100-5168
220-240V
50 Hz
13 VDC @625 ma
0950-3351
220-240V
50 Hz
13 VDC @800 ma
9100-5171
220-250V
50 Hz
13 VDC @625 ma
0950-3354
220-250V
50 Hz
13 VDC @800 ma
United Kingdom,
Singapore, Ireland,
Hong Kong
9100-5167
220-240V
50 Hz
13 VDC @625 ma
0950-3350
220-240V
50 Hz
13 VDC @800 ma
USA, Canada, Latin
America, Taiwan
9100-5165
110-127V
60 Hz
13 VDC @625 ma
0950-3348
110-127V
60 Hz
13 VDC @800 ma
China
Continental Europe
Japan
South Korea
South Africa, India
A-2 Specifications
Power Modules for J2591A, J3263A, and J3258B
Note: If two parts are listed for one country/region, either part can be used.
Part Num.
Input Rating
Output Rating
Australia, New
Zealand, Argentina
0950-3172
230-240VAC
50 Hz
13 VDC @300 ma
9100-5172
230-240VAC
50 Hz
13 VDC @625 ma
0950-2806
230-240VAC
50 Hz
13 VDC @300 ma
0950-2808
230-240VAC
50 Hz
13 VDC @625 ma
0950-3170
220-240V
50 Hz
13 VDC @300 ma
9100-5166
220-240V
50 Hz
13 VDC @625 ma
0950-3173
90-110V
50/60 Hz
13 VDC @300 ma
9100-5169
90-110V
50/60 Hz
13 VDC @625 ma
South Korea
9100-5168
220-240V
50 Hz
13 VDC @625 ma
South Africa, India
9100-5171
220-250V
50 Hz
13 VDC @625 ma
United Kingdom,
Singapore, Ireland,
Hong Kong
0950-3171
220-240V
50 Hz
13 VDC @300 ma
9100-5167
220-240V
50 Hz
13 VDC @625 ma
USA, Canada, Latin
America, Taiwan
0950-3169
110-127VAC
60 Hz
13 VDC @300 ma
9100-5165
110-127V
60 Hz
13 VDC @625 ma
China
Continental Europe
Japan
Specifications A-3
A Specifications
Country
Environmental
Operating
Non-Operating
Temperature
0°C to 55°C
(32°F to 131°F)
-40°C to 70°C
(-40°F to 158°F)
Relative Humidity
15% to 95% at 40°C
(104°F), non-condensing
90% at 65°C
(149°F)
Altitude
4.6 km (@15,000 ft.)
4.6 km (@15,000 ft.)
Acoustic Noise
Not applicable
Electromagnetic Emissions
FCC part 15 Class A (U.S.A.), ICES-003 (Canada), VCCI Class 1 (in
Japan), CISPR-22/EN55022 Class A, CNS 13438 (Taiwan), AS/NZS
3548 (Australia/New Zealand), GOST 29216 (Russia)
Note
For EU compliance, see the Declaration of
Conformity in Appendix B.
Safety
Products comply with:
IEC 950: (1991)+A1,A2,A3,A4/EN60950 (1992)+A1,A2,A3,A4
UL 1950
CSA 950
NOM-019-SCFI-1994 and NOM-001-SCFI-1993
A-4 Specifications
B
Regulatory Statements
FCC Statement (U.S.A)
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
interference to radio communications. Operation of this equipment in a
residential area is likely to cause interference in which case the user will
be required to correct the interference at their own expense.
Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to
this equipment not expressly approved by the Hewlett-Packard Company,
may cause interference and void the FCC authorization to operate this
equipment.
Attaching this product in an FCC Level B product results in an FCC Level A
Composite System as defined in the FCC Rules and Regulations.
The Federal Communications Commission has prepared a booklet titled
Interference Handbook (1986), which may be helpful to you. This booklet
stock number 004-000-004505-7) may be purchased from the Superintendent
of Documents, U.S. Government Printing Office, Washington, D.C. 20402.
European Community
This equipment complies with CISPR22/EN55022 Class A.
Note
This is a class A product. In a domestic
environment, this product may cause radio
interference, in which case the user may be required
to take adequate measures.
B-1
Declaration of Conformity
The following Declaration complies with ISO/IEC Guide 22 and EN 45014.
It identifies the product, the manufacturer's name and address, and
applicable specifications recognized in the European community.
B-2 Regulatory Statements
Australia. This equipment complies with Australian EMC
requirements.
Canada. Complies with Canadian EMC Class-A requirements.
Japan: VCCI Class 1.
Korea: RRL Statement.
Taiwan: Class A.
Regulatory
B Statements
Regulatory Statements B-3
Chinese Safety Statement:
B-4 Regulatory Statements
©Copyright 1999
Hewlett-Packard Company
8/99
Manual Part Number
5969-3466
*5969-3466*