Newstar NS-411KA User manual

Add to my manuals
10 Pages

advertisement

Newstar NS-411KA User manual | Manualzz
NEWSTAR 4-PORT KVM SWITCH, AUDIO
One Keyboard, Monitor, Mouse, Speaker, and
Microphone control 4PCs
User Manual
www.newstar.nl
T ABLE OF CONTENTS
INTRODUCTION --------------------------------------------------------- P1
FEATURES ---------------------------------------------------------------- P1
SPECIFICATIONS-------------------------------------------------------- P2
PACKAGE CONTENTS-------------------------------------------------- P2
HARDWARE INSTALLATION------------------------------------------- P3
FRONT PANEL LAYOUT------------------------------------------------- P3
REAR PANEL LAYOUT -------------------------------------------------- P3
USING THE NS-411KA -------------------------------------------------- P7
SELECT BUTTON-------------------------------------------------------- P7
KEYBOARD HOT KEY COMMANDS---------------------------------- P7
TROUBLESHOOTING--------------------------------------------------- P9
KEYBOARD---------------------------------------------------------------- P9
MOUSE--------------------------------------------------------------------- P9
VIDEO----------------------------------------------------------------------- P11
NS-411KA
NS-411KA
Specifications
Introduction
Thank you for purchasing the NEWSTAR KVM Switch, this product
will ensure easy and accurate control over 4 PCs through a single
console. The KVM Switch is compatible with 15 pin HDDB style
computers and comes with advanced features. It has keyboard,
mouse and video emulation for error free boot-ups and support is also
provided for the Microsoft Intellimouse. The KVM Switch supports
resolutions up to 2048 x 1536 without any deterioration of the
image quality. Switching between PCs can be accomplished in two
ways: through keyboard Hot Key commands or by using the convenient
front-panel Select push button controls. No other KVM switch lets you
control 4 computers from a control consoles simultaneously this
conveniently.
Features
6 Allows a user to control 4 computers from one console.
6 Built-in microphone and speaker jacks.
6 Works with Windows 95/98/2000/ME/NT/XP, Free BSD.
6 No drivers or other additional software required.
6 Keyboard and mouse emulation allows error-free boot-up.
6 The status of the (CAPS LOCK),( SCROLL LOCK) and (NUM LOCK)
keys is stored for each of the computers.
6 Uses inexpensive and commonly available cables.
6 Supports Monitor resolutions of up to 2048 x 1536.
6 Supports VGA, SVGA and MultiSync monitors.
6 Select Push-button or keyboard Hot Key control.
6 Comes with AutoScan mode for convenient automatic switching.
6 Front panel status LEDs give a clear indication of the active PC.
-1-
Physical Properties:
Width:
119mm
Height:
46mm
Depth:
105mm
Weight:
727g
Operation and Storage parameters:
Operating Temperature: 0~40 Degrees C
(32 to 104 Degrees F)
Storage Temperature: -20~60 Degrees C
(-4~140 Degrees F)
Humidity:
0~80% RH non condensing
PC port connections
All in one HDDB 15 pin Female (keyboard, mouse, monitor)
Audio Input/Output (3.5 mm jack)
Microphone Input/Output (3.5 mm jack)
Console connections
All in one HDDB 15 pin Female(keyboard, mouse, monitor)
Audio Input/Output (3.5 mm jack)
Microphone Input/Output (3.5 mm jack)
Package Contents
Item
Qty
NS-411KA
User Manual
KVM Cable
Cable Converter
1 piece
1 piece
4 pieces
1 piece
Remark
KVM
-2-
NS-411KA
NS-411KA
Hardware Installation
Hardware Installation
Here we will explain how to connect the console and the computers to
the NS-411KA switch unit. First the layout of front and rear panel will
be shown.
Please follow the steps below closely and in the order as shown.
Otherwise keyboard, mouse, audio, microphone and video errors may
occur.
Before starting with connecting your computers and console devices to
the NS-411KA make sure that everything is powered off. Connecting
devices while power is not off may lead to damage to your computers or
the NS-411KA. We will not be held responsible for damage caused.
Front Panel Layout
1.Place the NS-411KA in a convenient location, its small size makes it
easy to place it on the desktop. Do take the length of the cables in
consideration while placing the KVM switch unit.
2.Connect your keyboard, mouse and monitor to the NEWSTAR's
cable converter turns 15 pin HDDB.
.
Cable
Conventer
Rear Panel Layout
3.Connect your audio and microphone to the Rear of the NS-411KA. The
male 3.5mm plug to the speaker and microphone on the console of
your NS-411KA as shown below.
Microphone
Audio
3
4
NS-411KA
NS-411KA
Hardware Installation
Hardware Installation
4.Now the PC connections will be made with the PS/2 keyboard ,
mouse and 15-pin monitor (VGA) connections to the NEWSTAR 3 in
1 cable converter. Connect a cable with the male side to the rear
panel of the NS-411KA unit to the connector labeled PC1. Repeat
this for all PCs.
6.To finish the hardware installation, connect the microphone cables
from your computers to the NS-411KA unit. Using a second audio
cable, connect one end of the male 3.5mm plug to the microphone Out
jack of your sound card or computer and connect the other end to the
Microphone In jack of your NS-411KA. Repeat this for all PCs.
Audio
Keyboard
VGA
Mouse
Microphone
Microphone
5. Using the audio cable, connect one end of the male 3.5mm plug to
the speaker out jack of your sound card or computer and connect
the other end to the speaker in jack of your NA-411KA. Repeat this
for all PCs.
7. Now make sure to verify all cables. Especially keyboard and mouse
cables should be checked because they are easily switched due to
use of the same type of connector.
8. Attach the power supply to the NS-411KA unit and plug it into the
mains. Now you will see the LED for Port 1 light up,and you will hear
a beep. Switch on your monitor.
DC9V,600mA9 adaptor(optional)
Audio
9.Now power up all computers simultaneously, the first computer will
be shown on the monitor. You may check if the mouse and keyboard
work after the system has booted up. If this is OK, use the select
button to select the other computer and verify the functionality in the
same way. In case you find errors, first check all cables for proper
connections.
5
6
NS-411KA
NS-411KA
Using the NS-411KA
The NS-411KA switch unit provides two ways to select which computer
is the active system. Use either the Select button on the unit, or make
use of the keyboard Hot Key commands.
You may notice that the mouse can not be used for around 2 seconds
when the NS-411KA switches to another computer. This is normal and is
caused by synchronization that makes sure the mouse operates
properly.
every 10 seconds. This means that all computers will be shown on the
monitor in a row, starting with the first computer after the last one has
been shown.
In this mode there is no mouse or keyboard control, which is necessary
to prevent errors. Erratic input will result if a mouse move or keyboard
key press was to be given just as the unit switches to the next computer.
To exit Auto-Scan mode press the SPACE BAR. Now the NS-411KA will
stop at the last computer shown.
Select button
Pressing the Select button cycles through computers 1 ~ 4
Port Status
Keyboard Hot Key commands
To send Hot Key commands to the NS-411KA unit, press the SCROLL
LOCK Key twice within 2 seconds. Now you will be given a beep as
confirmation, now press a command key to give a Hot Key command.
The following commands are supported:
In Auto-Scan mode the NS-411KA unit will switch to the next computer
First Key
Second Key
Third Key
SCROLL LOCK
SCROLL LOCK
1
Switch to First PC
SCROLL LOCK
SCROLL LOCK
2
Switch to Second PC
SCROLL LOCK
SCROLL LOCK
↑
Switch to Previous PC
SCROLL LOCK
SCROLL LOCK
↓
Switch to Next PC
SCROLL LOCK
SCROLL LOCK
0
Go to Auto-Scan mode
7
Command
8
NS-411KA
NS-411KA
Troubleshooting
Keyboard
My keyboard is not detected, or a keyboard error is given during
boot-up.
6 Please verify that the keyboard cables are inserted properly.
6 Check to make sure that power cord is plugged in and is working
properly.
The computers all boot up properly, but the keyboard is not
functional.
6 Make sure the keyboard is plugged into the NS-411KA unit properly.
6 Verify that the keyboard works when plugged into the computer
directly. (You will have to shut down your computer first to do this).
6 Try using a different keyboard.
6 Make sure that the power adapter is plugged into the mains and that
it is working correctly. Its rating must be DC9V 600mA.
Mouse
My mouse is not detected during boot up.
6 Please verify that all mouse cables are inserted properly. Check
especially for a mix-up with the PS/2 keyboard cable, they have the
same kind of connector and are therefore easily confused.
6 Read your motherboard documentation and make sure that the PS/2
mouse IRQ is enabled. (This can for most computers be set in the
BIOS setup pages)
The computers boot properly but I can not use the mouse.
6 Please verify that the mouse is plugged into the NS-411KA unit
properly.
9
6 Make sure the mouse works proper when plugged into a computer
directly, you will need to reboot the system to test this.
6 Try using a different mouse.
6 Verify that the mouse complies with the PS/2 standard. A combination
mouse will work, but it must be set to PS/2 mode and the correct
serial mouse to PS/2 adapter must be used. A serial mouse with a
serial - PS/2 adapter will not work, since the mouse signals do not
comply with the PS/2 standard.
6 Make sure that the power adapter is plugged into the mains and that it
is working correctly. Its rating must be DC9V 600mA.
When I switch between computers mouse movement becomes
random.
6 Verify that your computers do not have more than one mouse driver
installed. Make sure that the driver is for a standard PS/2 or Microsoft
compatible PS/2 mouse. Also check with the mouse vendor to verify
you are using the latest mouse driver.
6 Check your config.sys and autoexec.bat files (if you run Windows
that is) and verify that only one mouse driver is loaded.
6 If a special mouse is used, such as cordless or scrolling mice, make
sure you use generic PS/2 mouse drivers. A non-standard PS/2
mouse may have extensions on the PS/2 protocol that are not
supported by the NS-411KA unit.
6 Do not move the mouse or press any mouse buttons while switching
from one system to the other.
6 Try resetting the mouse by unplugging it from the KVM4C unit for
about 3 seconds. Now mouse movement will be correct again.
6 Before booting up any PCs, the NS-411KA unit must be powered-up.
But before powering the NS-411KA unit up, the mouse and keyboard
must be connected first. Any deviation from this power-up sequence
may lead to erratic behavior of the systems.
10
NS-411KA
NS-411KA
Video
The image on my monitor is not clear.
6 Please verify that all video cables are inserted properly.
6 It may be that your resolution or refresh rate is too high. Try a lower
refresh rate, or try lowering the resolution.
6 Your video cable may be too long. Video signals are high frequency
signals and are therefore subject to interference. Please use video
cables that are as short as possible.
6 Make sure that the power adapter is plugged into the mains and that
it is working correctly. Its rating must be DC9V 600mA.
11
NS-411KA
FCC Certifications
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
6 Reorient or relocate the receiving antenna.
6 Increase the separation between the equipment and receiver.
6 Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
6 Consult the dealer or an experienced radio/TV technician for help.
6 Shielded interface cables must be used in order to comply with
emission limits.
6 You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void your
authority to operate the equipment.
6 This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
CE Mark Warning
This is a Class B product. In a domestic environment, this product
may cause radio interference, in which case the user may be required
to take adequate measures.
VCCI Warning
NS-411KA
LImited Warranty
NEWSTAR provides this limited warranty for its product only to the
person or entity who originally purchased the product from NEWSTAR
or its authorized reseller or distributor.
Limited Hardware Warranty:
NEWSTAR warrants that the hardware portion of the NEWSTAR
products described below ( Hardware ) will be free from material
defects in workmanship and materials from the date of original retail
purchase of the Hardware, for the period set forth below applicable to
the product type ( Warranty Period ) if the Hardware is used and
serviced in accordance with applicable documentation; provided that
a completed Registration Card is returned to an Authorized
NEWSTAR Service Office within ninety (90) days after the date of
original retail purchase of the Hardware. If a completed Registration
Card is not received by an authorized NEWSTAR Service Office within
such ninety (90) period, then the Warranty Period shall be ninety (90)
days from the date of purchase.
Product Type
PeriodProduct (excluding power supplies and fans)
YearsPower Supplies and Fans
parts and spare kits
Warranty
Three (3)Years
One (1) YearSpare
Ninety (90) days
NEWSTAR's sole obligation shall be to repair or replace the defective
Hardware at no charge to the original owner. Such repair or
replacement will be rendered by NEWSTAR at an Authorized
NEWSTAR Service Office. The replacement Hardware need not be
new or of an identical make, model or part; NEWSTAR may in its
discretion may replace the defective Hardware (or any part thereof)
w i t h a n y r e c o n d i t i o n e d p r o d u c t t h a t N E W S TA R r e a s o n a b l y
determines is substantially equivalent (or superior) in all material
respects to the defective Hardware.The Warranty Period shall extend
for an additional ninety (90) days after any repaired or replaced
Hardware is delivered. If a material defect is incapable of correction,
or if NEWSTAR determines in its sole discretion that it is not practical
to repair or replace the defective Hardware, the price paid by the
original purchaser for the defective Hardware will be refunded by
NEWSTAR upon return to NEWSTAR of the defective Hardware. All
Hardware (or part thereof) that is replaced by NEWSTAR, or for which
the purchase price is refunded, shall become the property of
NEWSTAR upon replacement or refund.
NS-411KA
Governing Law:
This Limited Warranty shall be governed by the Haarlem, city of The
Netherlands. Some states do not allow exclusion or limitation of
incidental or consequential damages, or limitations on how long an
implied warranty lasts, so the foregoing limitations and exclusions may
not apply. This limited warranty provides specific legal rights and the
product owner may also have other rights which vary from state to
state.
Trademarks:
Copyright 2003 NEWSTAR Europe. Contents subject to change without
prior notice. NEWSTAR is a registered trademark of NEWSTAR
Europe, All other trademarks belong to their respective proprietors.
Copyright Statement:
No part of this publication may be reproduced in any form or by any
means or used to make any derivative such as translation,
transformation, or adaptation without permission from NEWSTAR
Europe, as stipulated by the European Copyright.
NS-411KA
Registration Card
Print, type or use block letters.
Your name: Mr./Ms_________________________________________________________
Organization:________________________________Dept. ________________________
Your title at organization:____________________________________________________
Telephone:______________________________ Fax:_____________________________
Organization's full address:__________________________________________________
Country:_________________________________________________________________
Date of purchase (Month/Day/Year):___________________________________________
Product Model
Product
Serial
* Product installed in type of computer
* Product installed
(E.g.,Compaq(486)
incomputer serial Number
(* Applies to adapters only)
Product was purchased from:
Reseller's name:__________________________________________________________
Telephone:_______________________________________ Fax:____________________
Reseller's full address:_____________________________________________________
Answers to the following questions help us to support your product:
1. Where and how will the product primarily be used?
Home Office Travel Company Business Home Business Personal Use
2. How many employees work at installation site?
1 employee 2-9 10-49 50-99 100-499 500-999 1000 or more
3. What network protocol(s) does your organization use ?
XNS/IPX TCP/IP DECnet Others_____________________________
4. What network operating system(s) does your organization use ?
COMET LANsmart Novell NetWare NetWare Lite SCO Unix/Xenix PC NFS 3Com 3+Open
Banyan Vines DECnet Pathwork o Windows NT o Windows NTAS o Windows '95
o Others__________________________________________
5. What network management program does your organization use ?
o D-View o HP OpenView/Windows o HP OpenView/Unix o SunNet Manager o Novell NMS
o NetView 6000 o Others________________________________________
6. What network medium/media does your organization use ?
o Fiber-optics o Thick coax Ethernet o Thin coax Ethernet o 10BASE-T UTP/STP
o 100BASE-TX o 100BASE-T4 o 100VGAnyLAN o Others________________________________
7. What applications are used on your network?
o Desktop publishing o Spreadsheet o Word processing o CAD/CAM
o Database management o Accounting o Others________________________________________
8. What category best describes your company?
o Aerospace o Engineering o Education o Finance o Hospital o Legal o Insurance/Real Estate
o Manufacturing o Retail/Chainstore/Wholesale o Government
o Transportation/Utilities/CommunicationVAR o System house/company
o Other________________________________________________________________________
9. Would you recommend your NEWSTAR product to a friend?
o Yes o No o Don't know yet
10.Your comments on this product?
______________________________________________________________________________

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement