Printed in Spain
Gedruckt in Spanien
Imprimé en Espagne
Stampato in Spagna
Gedrukt in Spanje
Impreso en España
Impresso no Espanha
PIN
TÉLÉVISEUR COULEUR À ÉCRAN
CRISTAUX LIQUIDES (LCD)
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
TELEVISOR DE CRISTAL LÍQUIDO
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
: LC-46D65E/LC-52D65E
: LC-46DH65E/LC-52DH65E
: LC-46DH65S/LC-52DH65S
TINS-D808WJZZ
1
08P09-SP-NG
LCD-FARBFERNSEHGERÄT
NEDERLANDS
OPERATION MANUAL / BEDIENUNGSANLEITUNG / MODE D’EMPLOI / MANUALE DI ISTRUZIONI / GEBRUIKSAANWIJZING / MANUAL DE MANEJO /
MANUAL DE OPERAÇÃO
SHARP CORPORATION
LCD COLOUR TELEVISION
ESPAÑOL
D808WJZZ
Polígono Industrial Can Sant Joan
Calle Sena s/n
08174 SANT CUGAT DEL VALLÉS
BARCELONA (ESPAÑA)
LC-52D65E
LC-52DH65E
LC-52DH65S
PORTUGUÊS
LC-46D65E/LC-52D65E
LC-46DH65E/LC-52DH65E
LC-46DH65S/LC-52DH65S
SHARP ELECTRÓNICA ESPAÑA S.A.
LC-46D65E
LC-46DH65E
LC-46DH65S
(
) : LC-46D65E/46DH65E/46DH65S
[
] : LC-52D65E/52DH65E/52DH65S
: LC-46D65E/46DH65E/46DH65S
LC-52D65E/52DH65E/52DH65S
550.0
550,0
(1113.0 )/ [1252.0 ]
(1113,0 )/ [1252,0 ]
(106.6 )
(106,6 )
[111.9 ]
[111,9 ]
(101.4 )
(101,4 )
[95.6 ]
[95,6 ]
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
or )5) and of the same rating as above,
which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains
plug and fit an appropriate type.
(174.3 )
(174,3 )
[145.0 ]
[145,0 ]
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
400.0
400,0
(429.0 )/ [476.0 ]
(429,0 )/ [476,0 ]
(575.6 )/ [651.0 ]
(575,6 )/ [651,0 ]
400.0
400,0
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a
safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric
shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
295.0
295,0
(52.0 )
(52,0 )
[54.5 ]
[54,5 ]
SPECIAL NOTE FOR USERS IN THE U.K.
(704.0 )/ [796.0 ]
(704,0 )/ [796,0 ]
(756.0 )/ [851.0 ]
(756,0 )/ [851,0 ]
(1023.4 )/ [1157.0 ]
(1023,4 )/ [1157,0 ]
ENGLISH
• The illustrations and the OSD (On-Screen Display) in this operation manual are for explanation purposes and may vary slightly
from the actual operations.
• The examples used throughout this manual are based on the LC-52D65E model.
• LC-46DH65E, LC-46DH65S, LC-52DH65E and LC-52DH65S models are compatible with H.264 (MPEG4 H.264, MPEG4
AVC, MPEG4 AVC/H.264) compressed broadcasts.
ENGLISH
OPERATION MANUAL
Contents
Contents ............................................................................. 1
Introduction........................................................................ 2
Dear SHARP customer ................................................. 2
Important Safety Precautions ........................................ 2
Trademarks ................................................................... 2
Remote control unit....................................................... 3
TV (Front view) .............................................................. 4
TV (Rear view) ............................................................... 4
Preparation ........................................................................ 5
Supplied accessories .................................................... 5
Attaching the stand unit ................................................ 5
Inserting the batteries.................................................... 6
Using the remote control unit ........................................ 6
Cautions regarding the remote control unit............... 6
Quick guide ........................................................................ 7
Initial installation overview.............................................. 7
Before turning on the power.......................................... 8
Bundling the cables ................................................. 8
Initial auto installation .................................................... 9
Checking signal strength and channel strength ........ 9
Watching TV ..................................................................... 10
Daily operation ............................................................ 10
Switching on/off ..................................................... 10
Switching between analogue and
digital broadcasts ................................................ 10
Changing channels ................................................ 10
Selecting an external video source ......................... 10
Selecting a sound mode ........................................ 10
EPG (Electronic Programme Guide)............................. 11
EPG Overview............................................................. 11
Useful settings for using EPG ...................................... 11
Selecting a programme using EPG.............................. 12
Timer recording using EPG ......................................... 13
Cancelling the timer recording ..................................... 13
Teletext ....................................................................... 14
Using the MHEG-5 application (UK only) ..................... 14
Connecting external devices .......................................... 15
Introduction to connections......................................... 15
HDMI connection ................................................... 16
Component connection ......................................... 16
VIDEO connection ................................................. 16
SCART connection ................................................ 17
Controlling devices with SCART using AV Link ....... 17
Speaker/amplifier connection ................................. 18
Inserting a CA Card..................................................... 19
AQUOS LINK .................................................................... 20
Controlling HDMI devices using AQUOS LINK ............. 20
AQUOS LINK connection ............................................ 20
AQUOS LINK Setup .................................................... 21
Operating an AQUOS LINK device .............................. 22
Menu operation................................................................ 23
What is the MENU? .................................................... 23
Common operations .............................................. 23
Basic adjustment ............................................................. 24
Picture Settings........................................................... 24
AV MODE .............................................................. 25
Audio Settings ............................................................ 25
Power Save Settings ................................................... 26
Channel Settings......................................................... 27
Auto Installation ..................................................... 27
Digital channel settings .......................................... 27
Analogue channel settings ..................................... 28
Password/Parental lock settings ............................ 29
Language Settings (language, subtitle, multi audio) ..... 29
Useful Viewing functions ................................................ 30
Selecting the picture size ............................................ 30
Selecting the WSS (Wide Screen Signalling)
picture size automatically..................................... 30
Selecting the WSS (Wide Screen Signalling)
picture size manually ........................................... 30
Selecting the picture size manually ......................... 30
Selecting the recording picture size manually ......... 31
Selecting the HDMI picture size automatically ........ 31
Other picture and audio settings ................................. 31
Adjusting image position ........................................ 31
Automatic volume adjustment ................................ 31
Emphasising dialogue ............................................ 31
Outputting audio only............................................. 31
Display Settings .......................................................... 32
Channel display ..................................................... 32
Time and Title display ............................................ 32
Other useful features ...................................................... 33
Setting when using external devices ........................... 33
Input source settings ............................................. 33
Skipping specified inputs ....................................... 33
Colour system settings .......................................... 33
Additional features ...................................................... 33
Connecting a USB device ........................................... 34
USB Photo Viewer/Music Player ................................. 34
Photo Mode........................................................... 34
Music Mode ........................................................... 35
USB device compatibility ............................................ 35
Connecting a PC.............................................................. 36
Connecting a PC ........................................................ 36
Setting audio input ................................................. 36
Displaying a PC image on the screen .......................... 36
Selecting the picture size ....................................... 36
Adjusting the PC image automatically .................... 37
Adjusting the PC image manually ........................... 37
Selecting input resolution ............................................ 37
RS-232C port specifications ....................................... 38
PC compatibility chart ................................................. 39
RS-232C command list............................................... 39
Appendix .......................................................................... 40
Troubleshooting .......................................................... 40
Updating your TV via DVB-T ....................................... 41
Reset .......................................................................... 41
Identification................................................................ 41
Specifications ............................................................. 42
Optional accessory ..................................................... 42
End of life disposal ...................................................... 43
1
Introduction
Dear SHARP customer
Thank you for your purchase of the SHARP LCD colour TV product. To ensure safety and many years of troublefree operation of your product, please read the Important Safety Precautions carefully before using this product.
Important Safety Precautions
• Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners.
• Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, laundry tub,
swimming pool and in a wet basement.
• Do not place vases or any other water-filled containers on this product. The water may spill onto the
product causing fire or electric shock.
• Stand—Do not place the product on an unstable cart, stand, tripod or table. Doing so can cause the
product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When
mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting
hardware recommended by the manufacturer.
• When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops,
excessive force and uneven floor surface can cause the product to fall from the cart.
• Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover or
block these vents and openings since insufficient ventilation can cause overheating and/or shorten the
life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they
can block ventilation openings. This product is not designed for built-in installation; do not place the
product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
• The LCD panel used in this product is made of glass. Therefore, it can break when the product is
dropped or impact applied. If the LCD panel is broken, be careful not to be injured by broken glass.
• Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
• To prevent fire, never place any type of candle or naked flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• There is power consumption always if main plug is connected.
• Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high
voltage and other dangerous conditions. Request a qualified person to perform servicing.
The LCD panel is a very high technology product, giving you fine picture details.
Due to the very large number of pixels, occasionally a few non-active pixels may appear on the screen as a fixed point of
blue, green or red. This is within product specifications and does not constitute a fault.
Precautions when transporting the TV
When transporting the TV, never carry it by holding onto the speakers. Be sure to always carry the TV by two people holding
it with two hands—one hand on each side of the TV.
Trademarks
• “HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.”
• Manufactured under license from Dolby Laboratories.
• “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
• The “HD ready” Logo is a trademark of EICTA.
• The DVB logo is the registered trademark of the Digital Video Broadcasting—DVB—project.
• “x.v.Colour” and
are trademarks of Sony Corporation.
NOTE
• LC-46D65E and LC-52D65E models are compatible with Dolby Digital.
• LC-46DH65E, LC-46DH65S, LC-52DH65E and LC-52DH65S models are compatible with Dolby Digital Plus.
2
Introduction
Remote control unit
B (Standby/On)
(Page 10)
2 Buttons for useful operations
m (Teletext)
ATV: Display analogue teletext (Page
14).
DTV: Select MHEG-5 and teletext for
DTV (Page 14).
k (Reveal hidden Teletext)
(Page 14)
[ (Subtitle)
Switch subtitle languages on/off
(Pages 14 and 29).
3 (Freeze/Hold)
Press to freeze a moving image on
the screen.
Teletext: Stop updating teletext
pages automatically or release the
hold mode.
1 (Subpage)
(Page 14)
v (Top/Bottom/Full)
Set the area of magnification in
teletext mode (Page 14).
3 0–9 numeric buttons
Set the channel.
Enter desired numbers.
Set the page in teletext mode.
• When the five Nordic countries
(Sweden, Norway, Finland,
Denmark, or Iceland) are selected
in the country setting from “Auto
Installation” (page 27), DTV
services are four digits. When
another country is selected, DTV
services are three digits.
4 A (Flashback)
Press to return to the previously
selected channel or external input.
5 DTV
Press to access digital TV mode.
6 ATV
Press to access conventional
analogue TV mode.
7 2 (Sound mode)
Select a sound multiplex mode
(Page 10).
8 ik/l (Volume)
Increase/decrease TV volume.
9 e (Mute)
TV sound on/off.
0 f (WIDE MODE)
Select a wide mode (Pages 30 and
36).
Q AV MODE
Select a video setting (Page 25).
1
1
2
3
4
5
6
7
8
9
10
11
15
16
17
18
19
20
21
22
12
13
23
14
24
25
E END
Exit the “MENU” screen.
R R/G/Y/B (Colour) buttons
The coloured buttons are
correspondingly used to select the
coloured items on the screen (e.g.
EPG, MHEG-5, Teletext).
T b (INPUT SOURCE)
Select an input source (Page 10).
Y EPG
DTV: Display the EPG screen (Pages
11–13).
U RADIO
DTV: Switch between Radio and
Data mode.
• When only data broadcasting (no
radio broadcasting) is transmitted
by DVB, the radio broadcasting
will be skipped.
I P. INFO
Press to display programme
information which is transmitted
through digital video broadcasting in
the upper left corner of the screen
(DTV only).
O Pr/s
Select the TV channel.
P p (Display information)
Press to display the station
information (channel number, signal,
etc.) in the upper right corner of the
screen (Page 32).
A SLEEP
Press to schedule a time for the TV
to automatically standby (Page 26).
S MENU
“MENU” screen on/off.
D 6 (Return)
Return to the previous “MENU”
screen.
F ACTION (Action Mode)
This key does not work on this
model.
G AQUOS LINK buttons
If external equipment such as a
AQUOS BD Player is connected via
HDMI cables and is AQUOS LINK
compatible, you can use these
AQUOS LINK buttons. See pages 20
and 22 for details.
W a/b/c/d (Cursor)
Select a desired item on the setting
screen.
OK
Execute a command within the
“MENU” screen.
ATV/DTV: Display the programme
list when no other “MENU” screen is
running.
3
Introduction
TV (Front view)
Remote control sensor
OPC sensor
OPC indicator
B (Standby/On) indicator
TV (Rear view)
1
11
16
2
4
5
3
12
6
13
14
15
a (Power) button
7 8
9
MENU button
10
WARNING:
Excessive sound pressure from earphones and headphones can cause hearing loss.
EXT4 (ANALOGUE RGB/AUDIO)
terminals*
HDMI1 (HDMI) terminal
HDMI2 (HDMI/AUDIO) terminals*
EXT3 (COMPONENT/AUDIO)
terminals
OUTPUT (AUDIO) terminals
DIGITAL AUDIO OUTPUT terminal
1
2
3
4
5
6
4
7
8
9
10
11
12
13
14
15
16
Antenna terminal
RS-232C terminal
EXT1 (RGB) terminal
EXT2 (RGB) terminal
COMMON INTERFACE slot
EXT8 terminals
HDMI3 (HDMI) terminal
USB terminal
Headphones
AC INPUT terminal
b (INPUT SOURCE)
button
Pr/s
Programme (channel)
buttons
ik/l Volume
buttons
* The HDMI2 and EXT4 terminals
can both use the same audio input
terminal. However, the proper item
must be selected in the “PC Audio
Select” menu (Refer to page 36 for
details).
Preparation
Supplied accessories
Remote control unit
(g1)
AC cord (g1)
Cable clamp (g1)
Stand unit (g1)
Page 8
Page 5
Product shape varies in some countries.
Pages 3 and 6
Page 8
• Operation manual (This publication)
• “AAA” size alkaline battery (g2) ... Page 6
Attaching the stand unit
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work, spread cushioning over the surface on which you will be laying the TV. This will prevent
it from being damaged.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
1
Confirm that there are eight screws (four short
screws and four long screws) with the stand
unit.
2
Attach the supporting post for the stand unit
onto the base using the four long screws with
the hex key (supplied) as shown.
3
Inserting the stand.
1 Insert the stand into the openings on the
bottom of the TV (Hold the stand so it will
not drop from the edge of the base area).
2 Insert and tighten the four short screws into
the four holes on the rear of the TV.
Hex key
Short
screw
Hex key
Soft
cushion
Long
screw
Supporting
post
NOTE
• To detach the stand unit, perform the steps in reverse
order.
5
Preparation
Inserting the batteries
Before using the TV for the first time, insert two supplied “AAA” size alkaline batteries. When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
1 Open the battery cover.
2 Insert two supplied “AAA” size alkaline batteries.
• Place batteries with their terminals corresponding to the
(e) and (f) indications in the battery compartment.
3
Close the battery cover.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you
find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
• When replacing the batteries, use alkaline batteries instead of zinc-carbon ones.
Note on disposing batteries:
The batteries provided contain no harmful materials such as cadmium, lead or mercury.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household
rubbish. Deposit any used batteries free of charge into the designated collection containers set up at commercial
businesses.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control
unit and sensor may prevent proper operation.
5m
30°
30°
Remote control sensor
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock. In addition, do not expose the
remote control unit to liquids, and do not place in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight. The heat
may cause deformation of the unit.
• The remote control unit may not work properly if the remote control sensor of
the TV is under direct sunlight or strong lighting. In such cases, change the
angle of the lighting or the TV, or operate the remote control unit closer to the
remote control sensor.
6
Quick guide
Initial installation overview
Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary
depending on your TV installation and connection.
1
Preparation
n Connect an antenna cable to
the antenna terminal (Page 8).
2
3
Power on and
run the auto
installation
Watch TV
n Turn on the power using a on n Congratulations!
Now you can watch TV.
the TV (Page 10).
o If necessary, adjust the
antenna to attain maximum
signal reception (Page 9).
Connect
external devices
o Run the initial auto installation
(Page 9).
o If necessary, insert a CA card
into the CI slot to watch
scrambled broadcasts (Pages
8 and 19).
✔
Language setting
English
Italiano
Home/Store setting
HOME
(Page 8).
✔
STORE
Country setting
Austria
A
Finland
FIN B/G
Greece
GR B/G
✔
o Connect external
audio devices such as
speakers/amplifier as
instructed (Pages 15
and 18).
B/G
Channel search setting
Digital Search
Product shape varies in some countries.
devices such as a
DVD player/recorder
as instructed (Pages
15–17).
Svenska
✔
p Connect the AC cord to the TV
n Connect external
Analogue Search
Start searching
channels
7
Quick guide
Before turning on the power
1 Carefully insert the CI
Module in the CI slot
with the contact side
forward.
2 The logo on the CI
Module must be
facing outward from
the rear of the TV.
Standard
DIN45325 plug
(IEC 169-2) 75 q
coaxial cable
Supplying power to the antenna
You must supply power to the antenna in order to receive
digitally/terrestrially broadcast stations after connecting the
antenna cable to the antenna terminal on the rear of the TV.
1 Press MENU and the “MENU” screen displays.
2 Press c/d to select “Setup”.
3 Press a/b to select “Antenna Setup-DIGITAL”, and then press
OK.
4 Press a/b to select “Supply Voltage”, and then press OK.
5 Press c/d to select “On”, and then press OK.
Place the TV close to the
AC outlet, and keep the
power plug within reach.
AC cord
Product shape varies in some countries.
Mounting the TV on a wall
• This TV should be mounted on a wall only with the wall mount bracket available from SHARP (Page
42). The use of other wall mount brackets may result in an unstable installation and may cause
serious injuries.
• Mounting the LCD colour TV requires special skills and should only be performed by qualified service
personnel. Customers should not attempt to do the work themselves. SHARP bears no responsibility
for improper mounting or mounting that results in accident or injury.
• You can ask qualified service personnel about using an optional bracket to mount the TV to a wall.
• To use this TV mounted on a wall, first remove the adhesive tape at the two locations on the rear of the TV, and
then use the screws supplied with the wall mount bracket to secure the bracket to the rear of the TV.
• When you mount the TV on a wall, you should attach the supporting post.
When using wall mount bracket AN-52AG4
You can check the centre of the TV screen using the mark engraved on the wall mount bracket when mounting
the TV on the wall.
LC-46D65E, LC-46DH65E, LC-46DH65S: The centre of the TV screen is at the mark “b” on the wall bracket.
LC-52D65E, LC-52DH65E, LC-52DH65S: The centre of the TV screen is 7.3 mm below the mark “f” on the wall bracket.
Bundling the cables
Cable clamp
Bundle the cables with
the clamp.
8
Quick guide
6
Initial auto installation
When the TV is powered on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings
one after another.
Confirm the following before turning
on the power
E Is the antenna cable connected?
E Is the AC cord plugged in?
1
Press a on the TV.
• The initial auto installation wizard appears.
2
Setting the OSD language.
English
Italiano
Svenska
3
Press a/b/c/d to select the desired language,
and then press OK.
Selecting the location of the TV.
HOME
• To abort the initial auto installation in progress, press 6.
NOTE
• If you turn off the power on the TV after performing step 5,
the initial auto installation wizard does not appear. The auto
installation function allows you to execute the installation
again from the “Setup” menu (Page 27).
• The initial auto installation wizard will go off if you leave
the TV unattended for 30 minutes before searching for
channels in step 6.
Checking signal strength and
channel strength
If you install a DVB-T antenna for the first time or
relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking
the antenna setup screen.
1 Press MENU and the “MENU” screen displays.
2 Press c/d to select “Setup”.
3 Press a/b to select “Antenna Setup-DIGITAL”,
and then press OK.
E Checking signal strength
Press a/b to select “Signal Strength”.
STORE
Supply Voltage
Press c/d to select where you will use this TV,
and then press OK.
Signal Strength
Channel Strength
• HOME: “STANDARD” will be the default value for the “AV
MODE” setting.
• STORE: “DYNAMIC (Fixed)” will be the default value for the
“AV MODE” setting. If the “AV MODE” is changed, the TV will
automatically switch back to “DYNAMIC (Fixed)” when there
is no signal input from the TV or remote control unit for 30
minutes.
4
Setting the country.
Austria
A
Finland
FIN B/G
Greece
GR B/G
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
Current
Quality
0
Max
0
Current
0
Max
0
Press a/b to select “Channel Strength”, and
then press OK.
B/G
• You can input a specified frequency band using the 0–9
numeric buttons.
Signal Strength
Press a/b/c/d to select your country or area,
and then press OK.
Channel Strength
Starting channel search.
Analogue Search
Press c/d to select “Digital Search” or “Analogue
Search”, and then press OK.
• If you want to search for more broadcasts, execute
“Additional Search” from the “Programme Setup” menu
(Pages 27 and 28).
• To watch both analogue broadcasts and digital broadcasts,
you should perform the channel search setting for each
format.
4
7
CH No.
4 . 0
MHz
21
Signal Strength
• This setting screen only appears during the first installation.
Digital Search
21
E Checking channel strength
Supply Voltage
5
CH No.
Signal Strength
4
Current
Quality
0
Max
0
Current
0
Max
0
Position and align the antenna so that the
maximum possible values for “Signal Strength”
and “Quality” are obtained.
NOTE
• The values of “Signal Strength” and “Quality” indicate when
to check the appropriate alignment of the antenna.
EXAMPLE
• If you execute “Digital Search” in the initial auto installation
wizard, you should perform “Analogue Search” from “Auto
Installation” under the “Setup” menu (Pages 27 and 28).
9
Watching TV
Daily operation
Selecting an external video source
Switching on/off
Turning on/off the power
Press a on the TV.
Switch it off by pressing a on the TV.
Once the connection is made, press
b to display the “INPUT SOURCE”
screen, and then press a/b to
switch over to the appropriate
external source with OK.
INPUT SOURCE
TV
EXT1
EXT2
EXT3
EXT4
HDMI1
NOTE
• When turning off the power using
a on the TV, EPG data (Electronic
programme guide) will be lost, and
programmed timer recordings will
not be performed by the TV.
Selecting a sound mode
E DTV mode:
If multi sound modes are received, each time you
press 2 the mode switches as follows.
Audio (ENG) : STEREO
L/R
Standby mode
L
R
LR
E To standby mode
Audio (ENG) : CH A
If the TV is switched on, you can switch it to standby
by pressing B on the remote control unit.
CH A
CH B
CH AB
E Switching on from standby
From standby, press B on the remote control unit.
Audio (ENG) : MONO
Press c/d to select L or R sound when the STEREO
or DUAL MONO screen is displayed.
Audio (ENG) : STEREO
TV indicator status
L/R
B indicator
Status
Off
Power off
Green
Power on
Red
Standby
R
LR
NOTE
• The sound mode screen disappears in six seconds.
• Selectable items vary depending on the received broadcasts.
E ATV mode:
Each time you press 2, the mode switches as
shown in the following tables.
NOTE
• If you are not going to use this TV for a long period of time, be sure
to remove the AC cord from the AC outlet.
• A small amount of electric power is still consumed even when a is
turned off.
Switching between analogue and
digital broadcasts
E Watching digital
broadcasts
L
E Watching analogue
broadcasts
NICAM TV broadcasts selection
Selectable items
NICAM STEREO, MONO
NICAM CH A, NICAM CH B, NICAM CH AB, MONO
NICAM MONO, MONO
A2 TV broadcasts selection
Signal
Selectable items
Stereo
STEREO, MONO
Bilingual
CH A, CH B, CH AB
Monaural
MONO
Signal
Stereo
Bilingual
Monaural
NOTE
Changing channels
With Pr/s:
10
With 0–9:
• When no signal is input, the sound mode will display “MONO”.
Watching TV
EPG (Electronic Programme Guide)
EPG (Electronic Programme Guide) is a programme list that is displayed on the screen. With the EPG, you can
check the schedule of DTV/RADIO/DATA, view detailed information about them, tune to an event currently on-air
and set a timer for future events.
EPG Overview
E Basic functions
E Useful functions
E Select a programme using EPG (Page 12)
E Check programme information (Page 12)
E Search for a programme by category (Page 12)
E Search for a programme by date and time
(Page 12)
E Timer recording using EPG (Page 13)
Useful settings for using EPG
Common Operation
1
2
3
EPG display settings
Press MENU and the “MENU” screen displays.
Press c/d to select “Digital Setup”.
Press a/b to select “EPG Setup”, and then
press OK.
Digital Setup
REC Picture Size
[16:9 TV]
Download Setup
[Yes]
If you want to use the EPG for digital stations, select
“Yes”. The EPG data must be automatically captured
while the TV is in standby mode. After setting to “Yes”,
it may take some time to turn off the power using the
remote control unit due to the process of the data
capture.
EPG Setup
NOTE
Subtitle
• If the TV main power is switched off, the EPG data will not
be captured.
CI Menu
4
E EPG Setup (setting for receiving EPG
data)
Press a/b to select the desired item, and then
press OK (Example: “EPG Setup”, “Display
Range Setup”, etc.).
E Display Range Setup
The “Display Range Setup” allows you to select three
types of time spans for display on the screen.
Item
EPG Setup
Display Range Setup
Genre Icon Setup
Yes
No
Mode1: Displays six hours of programme information.
Mode2: Displays three hours of programme information.
Mode3: Changes to the EPG display format with a
vertical time span.
E Genre Icon Setup
5
Press a/b/c/d to select or adjust the desired
item, and then press OK (Example: “Yes”, “No”,
etc.).
You can grey out or place a mark on desired genres
and smoothly search for programmes you frequently
watch.
E Genre Icon List
Icon
Genre
Icon
Genre
Movie/Drama
Music/Ballet/Dance
News/Current affairs
Arts/Culture (without
music)
Show/Game show
Social/Political
Issues/Economics
Sports
Education/Science/
Factual topics
Children’s/Youth
programmes
Leisure hobbies
11
Watching TV
Selecting a programme using EPG
Basic Operation
The illustrations on this page are explained using three digit services.
E Display/Close the EPG screen
EPG
[DTV-TV]
Today
040
BBC News 24
10 : 00AM - 1 : 00 AM
Press EPG.
(Tue)20
(Wed)21
10 AM
BBC TWO
002
BBC THREE
007
BBC FOUR
010
BBC FIVE
012
CBBC Channel
2
061
BB22
062
1 Select the time span
BBC NEWS
BBC NEWS 24
340
BBC NEWS
BBCi
351
BBCi
SIT 1
994
SIT 2
995
SIT 3
996
SIT 4
E Select a programme
11
(Sat)24
(Sun)25 (Mon)26
[Mon]16/04 10:57 AM
1
2
1
3
This is BBC THREE
BBC NEWS
BBC NEWS
BBCi
997
SIT 5
998
BBC ONE
999
: Select
(Fri)23
0 PM
This is BBC THREE
030
BBC 1
(Thu)22
BBC News
OK
: Enter
6
This is BBC THREE
: Back
: Exit R Programme info.
EPG
Press c/d to select the time span you want to search.
G Search By Genre
3
• Continue to press d to display programmes in the next time span.
Y
Search By Date
4
B Timer List
5
2 Select the desired programme
Press a/b to select the desired programme.
• If a or b are displayed on the left of the services, continue to press a/b to display next or previous screen.
Selecting a programme
3 Check programme information
5 Search for a programme by date/time
1
1
2
2
Press a/b/c/d to select the programme you
want to check.
Press R.
Press Y.
Press c/d to select the desired time span, and
then press OK.
Programme Information
040
BBC News 24
10 : 00AM - 1 : 00 AM
Search by Time
Programme Info.
10 AM
B Next
B Next
: Select Time
11
BBC TWO
002
BBC THREE
007
BBC FOUR
010
BBC FIVE
012
CBBC Channel
030
BBC 1
061
BB22
062
BBC NEWS 24
340
BBC NEWS
BBCi
351
BBCi
0 PM
1
2
: Select Time
3
OK
OK
BBC NEWS
BBC TWO
BBC NEWS
BBC NEWS
BBCi
Press G.
Press a/b to select the desired genre, and then
press OK.
Press a/b to select a programme you want to
watch, and then press OK.
Genre
Movie/Drama
[Today] AM
[Today] PM
[Tue] 20 AM
[Tue] 20 PM
Movie/Dramaaffairs
News/Current
CBBC Cahnnel
030
time
Mon 19/05
10 : 50 AM - 11 : 05 AM
News/Current
affairs
Show/Game
show
BBC TWO
002
School is Lock
Mon 19/05
10 : 50 AM - 11 : 10 AM
Show/Game show
Sports
CBBC Cahnnel
030
Words and Pictures
Mon 19/05
11 : 05 AM - 11 : 20 AM
Sports
Children’s/Youth programmes
Children’s/Youth programmes
Music/Ballet/Dance
Music/Ballet/Dance
Arts/Culture (without music)
Arts/Culture (without music)
Social/Political
Social/PoliticalIssues/Economics
Issues/Economics
Education/Science/Factual
Education/Science/FactualTopics
Topics
Leisure
hobbies
Leisure
hobbies
• Refer to page 11 for the genre setting.
3
Today
to EPG
R Back
Back to EPG
: Enter
R
: Enter
11
0 PM -
6 PM -
06PM
PM6 PM
0 PM
10 AM
This is BBC THREE
This is BBC THREE
Press OK to tune to the selected programme.
12
6 AM AM 06PM
6 AM
4 Search a programme in a category
3
0 AM 0 AM 6 AM
The BBC’s rolling news service with headlines every 15 minutes.
R Back to EPG
1
2
Today
Search by Time
The BBC’s rolling news service with headlines every 15 minutes.
Programme Info.
R Back to EPG
3
Date/Time
BBC News
0 PM
6 PM
0 AM
0 AM
Enter
G
G Enter
1
+1 Week
Y
Y +1 Week
2
Next
Next
B
B Next
Next
3
002
BBC THREE
007
BBC FOUR
010
BBC FIVE
012
CBBC Channel
030
BBC 1
061
BB22
062
BBC NEWS 24
340
SIT 1
994
This is BBC THREE
BBC NEWS
BBC NEWS
This is BBC THREE
BBC NEWS
BBC NEWS
Press a/b to select the desired programme,
and then press OK.
NOTE
• When you select a programme outside of the current time
span, the timer setting screen is displayed (Page 13).
Watching TV
Timer recording using EPG
Cancelling the timer recording
You can record TV programmes using data from the
EPG.
1 Press EPG.
2 Press a/b/c/d to select the programme you
want to record, and then press OK.
3 Press c/d to select the preferred timer setting,
and then press OK.
Watch
Record
No
• If you select “No”, the TV returns to the EPG screen.
E Watching a programme at a set time
1
2
Press c/d to select “Watch”, and then press
OK.
Press c/d to select “Yes”, and then press OK.
• The selected TV programme is marked with an icon.
E Recording a programme at a set time
1
2
1
2
3
4
Press EPG.
Press a/b/c/d to select the programme on
timer setup, and then press OK.
Press c/d to select “Cancel”, and then press
OK.
Press c/d to select “Yes”, and then press OK.
E Cancelling using the B button on the
remote control unit
1
2
3
4
5
Press EPG.
Press B to display the timer recording screen.
Press a/b to select a programme with a set
timer recording you want to change, and then
press OK.
Press c/d to select “Cancel” and then press
OK.
Press c/d to select “Yes”, and then press OK.
Press c/d to select “Record”, and then press
OK.
Press c/d to select the preferred timer
recording type, and then press OK.
Item
AQUOS LINK: Records a programme at a set time when
a device compatible with AQUOS LINK is connected.
AV LINK: Records a programme at a set time when a
device compatible with AV LINK is connected.
VHS tape: Records a programme at a set time when a
device compatible with VHS tape is connected.
3
Press c/d to select “Yes”, and then press OK.
• The selected TV programme is marked with an icon.
NOTE
• Refer to pages 15–17 and 20–21 for connecting external
devices.
13
Watching TV
Buttons for teletext operations
Teletext
Buttons
What is Teletext?
Teletext broadcasts pages of information and
entertainment to specially equipped TV. Your TV
receives teletext signals broadcast by a TV network,
and decodes them into graphical format for viewing.
News, weather and sports information, stock
exchange prices and programme previews are among
the many services available.
Turning Teletext on/off
1
2
Select a TV channel or external source providing
a teletext programme.
Press m to display the Teletext.
• Many stations use the TOP operating system, while
some use FLOF (e.g. CNN). Your TV supports both
these systems. The pages are divided into topic
groups and topics. After switching on the teletext, up
to 2,000 pages are stored for fast access.
• Each time you press m, the screen switches as
shown below.
• Press m again to display the teletext on the right
screen and the normal image on the left screen.
• If you select a programme with no teletext signal, “No
Teletext available” displays.
• The same message displays during other modes if no
teletext signal is available.
Description
Pr/s
Increase or decrease the page number.
Colour (R/G/
Y/B)
Select a group or block of pages
displayed in the coloured brackets at the
bottom of the screen by pressing the
corresponding Colour (R/G/Y/B) on the
remote control unit.
0–9
Directly select any page from 100 to 899
by using the 0–9 numeric buttons.
v (Top/
Bottom/Full)
Switch the teletext image to Top, Bottom
or Full.
k (Reveal
hidden
Teletext)
Reveal or hide hidden information such
as an answer to a quiz.
3 (Freeze/
Hold)
Stop updating teletext pages
automatically or release the hold mode.
[ (Subtitle
for Teletext)
Display the subtitle or exit the subtitle
screen.
• Subtitles will not be displayed when
the service does not contain subtitle
information.
1 (Subpage)
Reveal or hide subpages.
• R button: Move to the previous
subpage.
• G button: Move to the following
subpage.
• These two buttons are shown on the
screen by the symbols “e” and “f”.
Using the MHEG-5 application (UK
only)
TELETEXT
Some services bring you programmes with the MHEG
(Multimedia and Hypermedia Expert Group) application
encoded, letting you experience DTV interactively.
When provided, the MHEG-5 application will start
when you press m.
Sample MHEG-5 screen
TELETEXT
NOTE
• Teletext will not work if the selected signal type is
RGB (Page 33).
14
Connecting external devices
E Before connecting ...
• Be sure to turn off the TV and any devices before making any connections.
• Firmly connect a cable to a terminal or terminals.
• Carefully read the operation manual of each external device for possible connection types. This also helps you
get the best possible audiovisual quality to maximise the potential of the TV and the connected device.
• Refer to page 36 for connecting a PC to the TV.
Introduction to connections
The TV is equipped with the terminals as shown below. Find the cable corresponding the TV’s terminal and
connect the device.
NOTE
• The cables illustrated in pages 15–18 are commercially available items.
Audio device (Page 18)
Optical audio cable
or
Audio cable
Component cable
Video recording device
(Pages 16 and 17)
Audio cable
SCART cable
Game console or
camcorder (Page 16)
AV cable
HDMI-certified cable
HDMI device (Page 16)
DVI/HDMI Cable
ø 3.5 mm stereo minijack cable
15
Connecting external devices
HDMI connection
Y
PB
PR
(CB)
(CR)
Component connection
Example of connectable devices
Example of connectable devices
E DVD player/recorder E Blu-ray player/recorder
E Game console
E VCR E DVD player/recorder
E Blu-ray player/recorder
The HDMI connections (High Definition Multimedia
Interface) permit digital video and audio transmission
via a connection cable from a player/recorder. The
digital picture and sound data are transmitted without
data compression and therefore lose none of their
quality. Analogue/digital conversion is no longer
necessary in the connected devices, which also would
result in quality losses.
You will enjoy accurate colour reproduction and
high quality images through the EXT3 terminal when
connecting a DVD player/recorder or other device.
Component
cable
HDMI-certified
cable
ø 3.5 mm
stereo
minijack
cable
Audio cable
DVI/HDMI
cable
R
L
AUDIO
Y
PB
(CB)
PR
(CR)
COMPONENT
VIDEO connection
DVI/HDMI conversion
Using a DVI/HDMI cable, the digital video signals of
a DVD can also be played via the compatible HDMI
connection. The sound must be fed in additionally.
• When connecting a DVI/HDMI cable to the HDMI terminal, the
image may not come in clearly.
• Both HDMI and DVI use the same HDCP copy protection method.
E When using the HDMI2 terminal
You must set the audio signal input source
depending on the type of HDMI cable connected
(Refer to page 36 for details).
HDMI-certified cable
Go to “MENU” > “Option” > “PC Audio
Select” > select “EXT4 (RGB)”.
DVI/HDMI cable
Go to “MENU” > “Option” > “PC Audio
Select” > select “HDMI2”.
NOTE
• If a connected HDMI device is AQUOS LINK compatible, you
can take advantage of versatile functions (Pages 20–22).
• Video noise may occur depending on the type of HDMI cable used.
Make sure to use a certified HDMI cable.
• When playing the HDMI image, the best possible format for the
picture will be detected and set automatically.
Supported video signal:
576i, 576p, 480i, 480p, 1080i, 720p, 1080p
See page 39 for PC signal compatibility.
16
Example of connectable devices
E VCR E DVD player/recorder
E Blu-ray player/recorder
E Game console E Camcorder
You can use the EXT8 terminal when connecting to a
game console, camcorder, a DVD player/recorder or
other device.
AV cable
Connecting external devices
SCART connection
Example of connectable devices
Example of connectable devices
E Decoder
E VCR E DVD player/recorder
E When using the EXT2 (SCART) terminal
If your VCR supports TV-VCR advanced AV Link
systems, you can connect the VCR using a fully wired
SCART cable.
SCART cable
SCART cable
SCART cable
Decoder
VCR
Decoder
NOTE
• In cases when the decoder needs to receive a signal from the TV, make sure to select the appropriate input terminal to which
the decoder is connected in “Manual Adjust” in the “Analogue Setting” menu (Page 28).
• TV-VCR advanced AV Link systems may not be compatible with some external sources.
• You cannot connect the VCR with decoder using a fully wired SCART cable when selecting “Y/C” under “EXT2” in the “Input
Select” menu.
Controlling devices with SCART using AV Link
This TV incorporates four typical AV Link functions for smooth connections between the TV and other audiovisual
equipment.
One Touch Play
While the TV is in standby mode, it automatically turns on and plays back the image from the audiovisual source
(e.g. VCR, DVD player/recorder).
TV Standby
When the TV enters standby mode, the connected audiovisual equipment (e.g. VCR, DVD player/recorder) enters
standby mode as well.
WYSIWYR (What You See Is What You Record)
When the remote control unit of the connected VCR has the WYSIWYR button, you can automatically start
recording by pressing the WYSIWYR button.
Preset Download
Automatically transfers the channel preset information from the tuner on the TV to the one on the connected
audiovisual equipment (e.g. VCR) via the EXT2 terminal.
NOTE
• Refer to the operation manuals of external equipment for details.
• The AV Link function works only when audiovisual equipment is connected to the EXT2 terminal with a fully wired SCART cable.
• The use of the AV Link function is only possible if the TV has enforced a complete auto installation with the connected
audiovisual equipment (Page 9, Initial auto installation).
The availability of the AV Link function depends on the audiovisual equipment used. Depending on the manufacturer and type
of equipment used, it is possible that the described functions may be completely or partially unusable.
17
Connecting external devices
Speaker/amplifier connection
Connect an amplifier with external speakers as shown below.
E Connecting an amplifier with digital audio
input
E Connecting an amplifier with analogue
audio input
Optical audio cable
Audio cable
R
DIGITAL AUDIO IN
Amplifier with
digital audio input
E After connecting
Digital audio output setting
After connecting an amplifier with digital audio
input and external speakers as shown, you should
set an audio output format compatible with
the programme you are watching or the device
connected.
Go to “MENU” > “Option” > “Digital Audio
Output” > select “PCM” or “Dolby Digital”.
NOTE
• LC-46D65E, LC-52D65E:
When you set this to “Dolby Digital”, and you receive
the Dolby Digital audio format, Dolby Digital audio is
output. Otherwise, PCM audio is output.
When you set this to “PCM”, PCM audio is output no
matter what audio formats you receive.
• LC-46DH65E, LC-46DH65S, LC-52DH65E, LC52DH65S:
When you set this to “Dolby Digital”, and you receive
the Dolby Digital or Dolby Digital Plus audio formats,
Dolby Digital audio is output. Otherwise, PCM audio is
output.
When you set this to “PCM”, PCM audio is output no
matter what audio formats you receive.
18
L
AUX OUT
R
L
AUX1 IN
Amplifier with
analogue audio input
Connecting external devices
Inserting a CA Card
Checking CI Module information
In order to receive coded digital stations, a Common
Interface Module (CI Module) and a CA Card must be
inserted in the CI slot of the TV (Page 8).
The CI Module and the CA Card are not supplied
accessories. They are usually available from your
dealers.
NOTE
Inserting the CA Card into the CI Module
3
1
With the side with the gold coloured contact
chip facing the side of the CI Module marked
with the provider’s logo, push the CA Card
into the CI Module as far as it will go. Note the
direction of the arrow printed on the CA Card.
• Make sure that the CI Module is properly inserted.
• This menu is only available for digital stations.
1
2
Press MENU and the “MENU” screen displays.
Press c/d to select “Digital Setup”.
• The content of this menu depends on the provider of
the CI Module.
Press a/b to select “CI Menu”, and then press
OK.
E Module
General information on CI Module displays.
E Menu
Adjustment parameters of each CA Card displays.
E Enquiry
You can input numerical values such as passwords
here.
NOTE
• The content of each screen depends on the provider of
the CI Module.
Inserting the CI Module in the CI slot
2
Carefully insert the CI
Module in the CI slot
with the contact side
forward. The logo on
the CI Module must be
facing outward from the
rear of the TV. Do not use
excessive force. Make
sure the module is not
bent in the process.
19
AQUOS LINK
Controlling HDMI devices using AQUOS LINK
What is AQUOS LINK?
Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you
can interactively operate compatible system devices (AV amplifier, DVD player/recorder,
Blu-ray player/recorder) using a single remote control unit.
NOTE
• AQUOS LINK-compatible AQUOS AUDIO speaker system and AQUOS Recorder are scheduled
to be on sale after the release of this TV (as of September 2008).
What you can do with AQUOS LINK
✔ One Touch Recording (DTV only)
You do not have to search for the remote control unit of your recording device. Press the
REC E or REC STOP H buttons inside the flip cover to start/stop recording what you
see on the recorder.
✔ One Touch Play
When the TV is in standby mode, it will automatically turn on and play back the image
from the HDMI source.
✔ Single remote control operation
AQUOS LINK automatically recognises the connected HDMI devices and you can
control the TV and the devices as if using a universal remote control unit.
✔ Operating Title list of external devices
In addition to displaying the TV’s own Timer list (Page 12), you can also call up the
external player’s Top menu or AQUOS BD Player’s/AQUOS Recorder’s Title list provided
that the devices support AQUOS LINK.
✔ Multiple control of HDMI devices
You can select which HDMI device to operate using the OPTION button.
NOTE
• When you use AQUOS LINK, make sure to use a certified HDMI cable.
• Point the remote control unit toward the TV, not to the connected HDMI device.
• Video noise may occur depending on the type of HDMI cable used. Make sure to use a certified
HDMI cable.
• Up to three HDMI recording devices, one AV amplifier and two players can be connected using
this system.
• These operations affect the HDMI device selected as the current external source. If the device
does not operate, turn on the device and select the appropriate external source using b.
• When you insert/remove HDMI cables or change connections, turn on all connected HDMI
devices before turning on the TV. Confirm that picture and audio are correctly output by selecting
“HDMI1”, “HDMI2” or “HDMI3” from the “INPUT SOURCE” menu.
AQUOS LINK connection
First connect the AQUOS AUDIO speaker system or an AQUOS BD Player/AQUOS Recorder that supports the
HDMI CEC protocol.
NOTE
• Refer to the operation manual of the device to be connected for further details.
• After unplugging connection cables or changing the connection pattern, turn on the power of the TV after all relevant devices’
power have been turned on. Change the external input source by pressing b, select the appropriate external source and
verify the audiovisual output.
• The cables illustrated in the following explanation are commercially available items.
20
AQUOS LINK
Connecting an AQUOS BD Player/AQUOS Recorder via
the AQUOS AUDIO speaker system
Connecting an AQUOS BD
Player/AQUOS Recorder only
Optical audio
cable
HDMI-certified cable
HDMI-certified
cable
HDMI-certified cable
AQUOS BD Player/
AQUOS Recorder
AQUOS AUDIO
speaker system
AQUOS BD Player/
AQUOS Recorder
AQUOS LINK Setup
AQUOS LINK Control
Set to “On” to enable HDMI CEC functions. When
turning on the power while “AQUOS LINK Control” is
set to “On”, the connected HDMI devises’ power will
be turned on in conjunction with the TV.
1 Press MENU and the “MENU” screen displays.
2 Press c/d to select “Option”.
3 Press a/b to select “AQUOS LINK Setup”, and
then press OK.
4 Press a/b to select “AQUOS LINK Control”,
and then press OK.
5 Press c/d to select “On”, and then press OK.
Auto Power On
If this is activated, the One Touch Play function
is enabled. While the TV is in standby mode, it
automatically turns on and plays back the image from
the HDMI source.
1 Repeat steps 1 to 3 in AQUOS LINK Control.
2 Press a/b to select “Auto Power On”, and then
press OK.
3 Press c/d to select “On”, and then press OK.
Selecting Recorder
Here, you can select a recorder for the recording from
several connected recorders.
1 Repeat steps 1 to 3 in AQUOS LINK Control.
2 Press a/b to select “Selecting Recorder”, and
then press OK.
3 Select the recorder, and then press OK.
NOTE
• If you have connected the AQUOS AUDIO speaker system
between the TV and an AQUOS Recorder, the external
source’s indication changes (e.g. from “HDMI1” to “HDMI1
(Sub)”).
Using Genre Info.
This function allows you to automatically switch to
the appropriate sound mode depending on the genre
information included the digital broadcast.
1 Repeat steps 1 to 3 in AQUOS LINK Control.
2 Press a/b to select “Using Genre Info.”, and
then press OK.
3 Press c/d to select “On”, and then press OK.
NOTE
• The factory default for this item is “Off”.
21
AQUOS LINK
Operating an AQUOS LINK device
AQUOS LINK allows you to operate the HDMIconnected device with a single remote control unit.
1 Open the remote control unit’s flip cover.
2 Press PLAY I to start playback of a title.
• See the right column, section “Playback of titles
using AQUOS LINK” if you want to start playback
using the list of the titles of the AQUOS BD Player/
AQUOS Recorder.
3
Press FWD J to fast forward.
Press REV G to reverse.
Press STOP H to stop.
Press B to turn the HDMI-connected device on/off.
Listening with the AQUOS AUDIO speaker system
You can choose to listen to the TV sound only from the
AQUOS AUDIO speaker system.
1 Open the remote control unit’s flip cover, and
then press OPTION.
AQUOS LINK Menu
1
2
NOTE
• If a connected device does not have this function or the
device is in a status where the menu cannot be displayed
(recording, entering standby, etc.), this function may not be
available.
Playback of titles using AQUOS LINK
This section explains how to play back a title in the
AQUOS BD Player/AQUOS Recorder.
1 Open the remote control unit’s flip cover, and
then press OPTION.
2 Press a/b to select “Top Menu/Title List”, and
then press OK.
• The linked recorder now powers on and the TV
automatically selects the appropriate external input
source.
• The title list data from the connected AQUOS BD
Player/AQUOS Recorder displays.
3
Recorder EPG
Top Menu/Title List
Media change
By AQUOS AUDIO SP
By AQUOS SP
Sound mode change
Setup Menu
Model select
2
Press a/b to select “By AQUOS AUDIO SP”,
and then press OK.
• The sound from the TV speaker and headphone
terminal is silenced and only the sound from the
AQUOS AUDIO speaker system is audible.
Listening with the AQUOS TV speaker system
You can choose to listen to the TV sound only from the
AQUOS TV speaker system.
1 Open the remote control unit’s flip cover, and
then press OPTION.
2 Press a/b to select “By AQUOS SP”, and then
press OK.
Manually changing the AQUOS AUDIO
speaker system’s sound mode
1
2
3
Open the remote control unit’s flip cover, and
then press OPTION.
Press a/b to select “Sound mode change”.
The sound mode changes every time you press OK.
• Refer to the operation manual of the AQUOS AUDIO
speaker system for details.
Calling up the menu of an external device
connected with the TV via HDMI
You can call up the menu of an HDMI CEC-compatible
external device (player, recorder, decoder, etc.) using
the “Setup Menu” function.
22
Open the remote control unit’s flip cover, and
then press OPTION.
Press a/b to select “Setup Menu”, and then
press OK.
Select the title with a/b/c/d, and then press
PLAY I.
Selecting media type for CEC-compatible
recorder
If your recorder has multiple storage media, select the
media type here.
1 Open the remote control unit’s flip cover, and
then press OPTION.
2 Press a/b to select “Media change”, and then
press OK.
3 Select the desired medium, such as DVD
recorder or HDD. The media type changes every
time you press OK.
HDMI device selection
If multiple HDMI devices are connected in a daisy
chain, you can specify which device to control here.
1 Open the remote control unit’s flip cover, and
then press OPTION.
2 Press a/b to select “Model select”, and then
press OK. The HDMI device changes every time
you press OK.
Recording via the AQUOS Recorder EPG
(only for recorders)
You can call up the CEC-compatible recorder’s EPG
and preset timer recordings using the TV’s remote
control unit.
1 Open the remote control unit’s flip cover, and
then press OPTION.
2 Press a/b to select “Recorder EPG”, and then
press OK.
• The external input source switches and the recorder’s
EPG is displayed.
3
Select the programme to record.
• Refer to the operation manual of the recorder for details.
Menu operation
What is the MENU?
• You need to call up the OSD to perform settings for the TV. The OSD for the settings is called “MENU”.
• The “MENU” enables various settings and adjustments.
• The “MENU” can be operated with the remote control unit.
Common operations
1
Display the MENU
Screen
2
Select an item
Press a/b/c/d to select/adjust the
desired menu, and adjust the item to
the desired level, and then press OK.
Press MENU and the “MENU”
screen displays.
Picture
Press 6 to return to the previous
“MENU” page.
DYNAMIC
OPC
[Off]
Backlight
[+14]
–16
+16
Contrast
[+30]
0
+40
Brightness
[0]
–30
+30
Colour
[0]
–30
+30
Tint
[0]
–30
+30
Sharpness
[0]
–10
+10
E Selecting in the MENU
Advanced
Reset
ECO
Energy Save
[Off]
No Signal Off
[Disable]
No Operation Off
[Disable]
Sleep Timer
3
E Selecting options
Exit the MENU
screen
The operation will exit the “MENU”
screen if you press END before it is
completed.
Digital Search
Analogue Search
NOTE
• “MENU” options differ in the selected input modes, but the operating procedures are the same.
• The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly from the actual screens.
• Items with 4 cannot be selected for various reasons.
Operation without a remote control unit
This function is useful when there is no remote control
unit within your reach.
1 Press MENU and the “MENU”
screen displays.
2 Press Pr/s instead of a/b
or ik/l instead of c/d to
select the item.
3 Press b to complete the setting.
NOTE
About the Guide Display
The Guide Display at the bottom of the screen shows
operations with the OSD.
: Select
OK
: Enter
6
: Back
MENU
: End
The bar above is an operational guide for the remote
control unit. The bar will change in accordance with
each menu setting screen.
• The “MENU” screen will disappear if left unattended for several
seconds.
23
Basic adjustment
Picture Settings
Picture
Advanced
Picture
DYNAMIC
OPC
[Off]
Backlight
[+14]
–16
+16
Contrast
[+30]
0
+40
Brightness
[0]
–30
+30
Colour
[0]
+30
–30
Tint
[0]
–30
+30
Sharpness
[0]
–10
+10
This TV provides various advanced functions for optimising
the picture quality.
Y [
0] f30
e30
Film Mode
G [
0] f30
e30
Active Contrast
C [
0] f30
e30
DNR
B [
0] f30
e30
3D-Y/C
M [
0] f30
e30
Advanced
Monochrome
Reset
Range of OPC
C.M.S.-Hue
Picture
This function adjusts the hue of a selected colour using a sixcolour adjustment system.
OPC
Automatically adjusts the brightness of the screen.
Item
Off: The brightness is fixed at the value set in “Backlight”.
On: Automatically adjusts.
On:Display: Displays the OPC effect on the screen while
adjusting the brightness of the screen.
Colour Temp.
Adjusts the colour temperature to give the best white image.
Item
NOTE
• When set to “On”, the TV senses the surrounding light and
automatically adjusts the backlight brightness. Make sure
no object obstructs the OPC sensor, which could affect its
ability to sense surrounding light.
Picture
Adjusts the picture to your preference with the
following picture settings.
Adjustment items
c button
High: White with bluish tone.
Mid-High: Intermediate tone between “High” and “Middle”.
Middle: Natural tone.
Mid-Low: Intermediate tone between “Middle” and “Low”.
Low: White with reddish tone.
Film Mode
Picture adjustments
Selectable
items
C.M.S.-Saturation
This function increases or decreases the saturation of a
selected colour using a six-colour adjustment system.
Automatically detects a film-based source (originally encoded
at 24 or 25 frames per second, depending on the vertical
frequency), analyses it and then recreates each still film frame
for high-definition picture quality.
Active Contrast
d button
Backlight
The screen dims
The screen brightens
Contrast
For less contrast
For more contrast
Brightness
For less brightness
For more brightness
Colour
For less colour
intensity
For more colour
intensity
Tint
Skin tones become
purplish
Skin tones become
greenish
Sharpness
For less sharpness
For more sharpness
Automatically adjusts the contrast of an image according to
the scene.
DNR
“DNR” (Digital Noise Reduction) produces a clearer image
(“Off”, “High”, “Middle”, “Low”).
3D-Y/C
Provides high quality images with minimal dot crawl and cross
colour noise by detecting changes in the image.
Item
Standard: Normal adjustment.
Fast: Sets the optimum image quality for fast-moving images.
Slow: Sets the optimum image quality for slow-moving images.
NOTE
• “3D-Y/C” may not operate depending on the input signal type or
when the input signal is noisy.
• “3D-Y/C” has even more effect on composite video signals (CVBS).
24
Basic adjustment
Audio Settings
Monochrome
For viewing a colour video in black & white.
Range of OPC
Audio
DYNAMIC
The brightness level range of the OPC sensor’s
automatic adjustments can be set according to your
preferences. The adjustment range of the OPC sensor
can be set to a maximum of e16 and a minimum of
f16.
Treble
[ 0]
–15
+15
Bass
[ 0]
–15
+15
Balance
[ 0]
L
R
Surround
[Off]
Reset
Selectable
items
Description
Max.
f16 through e16
Min.
f16 through e16
NOTE
• This function is available only when the “OPC” setting is set
to “On” or “On:Display”.
• The maximum setting cannot be set to a smaller number
than the minimum setting.
• The minimum setting cannot be set to a bigger number
than the maximum setting.
• The maximum and minimum settings cannot be set to the
same number.
• Depending on the brightness of the surrounding light, the
OPC sensor might not operate if the adjustment range is
small.
AV MODE
“AV MODE” gives you several viewing options to
choose from to best match the system environment,
which can vary due to factors like room-brightness,
type of programme watched or the type of image input
from external equipment.
1 Press AV MODE.
2 Each time you press AV MODE, the mode
changes.
Audio
Audio adjustment
You can adjust the sound quality to your preference
with the following settings.
Selectable
items
c button
d button
Treble
For weaker treble
For stronger treble
Bass
For weaker bass
For stronger bass
Balance
Decrease audio from
the right speaker
Decrease audio from
the left speaker
Audio
Surround
This function allows you to enjoy realistic live sound.
• You can also switch the mode on the “Picture” and
“Audio” menu screen by pressing AV MODE.
Item
STANDARD: For a highly defined image in a normally
bright room.
MOVIE: For viewing a movie in a darkened room.
GAME: For playing of video games.
PC*: For PC.
x.v.Colour**: Produce realistic colour on the TV screen
unlike any other signal.
USER: Allows you to customise settings as desired. You
can set the mode for each input source.
DYNAMIC (Fixed): For a clear-cut image emphasising
high contrast for sports viewing (The “Picture” and
“Audio” settings cannot be adjusted).
DYNAMIC: For a clear-cut image emphasising high
contrast for sports viewing.
NOTE
• The item marked with * is available only when selecting
“HDMI1”, “HDMI2”, “HDMI3” or “EXT4” from the “INPUT
SOURCE” menu.
• The item marked with ** is available only when accepting
an “x.v.Colour” signal through an HDMI terminal.
• For input source “USB”, you can only select “USER (USB)”,
“DYNAMIC (Fixed)”, “DYNAMIC” and “STANDARD”.
25
Basic adjustment
Power Save Settings
ECO
No Signal Off
ECO
Energy Save
[
Standard]
No Signal Off
[Disable]
No Operation Off
[Disable]
When set to “Enable”, the TV will automatically enter
standby mode if there is no signal input for 15 minutes.
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
Sleep Timer
NOTE
• Even if a TV programme finishes, this function may not
operate because of interference from other TV stations or
other signals.
ECO
Energy Save
ECO
This function enables you to automatically reduce the
backlight brightness in order to decrease the power
consumption and increase the backlight life span.
Item
Standard: Reduces the backlight brightness by 20%.
Advanced: Reduces the backlight brightness by 30%.
Off: The backlight brightness is the same value of your
settings in the selected “AV MODE”.
No Operation Off
The TV will automatically enter standby mode if no
operations are performed during the time span you set
(“30min.” or “3hr.”).
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
NOTE
ECO
• This function does not work when “AV MODE” is set to
“DYNAMIC (Fixed)”.
Sleep Timer
E “Energy Save” status icons
Icon
Allows you to set a time when the TV automatically
enters standby mode.
Description
“Energy Save” is set to “Standard”.
NOTE
“Energy Save” is set to “Advanced”.
When “Energy Save” is set to “Standard” or
“Advanced”, “Energy Save” status icons appear in the
“Picture” menu and channel information windows as
shown below.
EXAMPLE
Picture
DYNAMIC
OPC
[On]
Backlight
[+14]
–16
+16
Contrast
[+30]
0
+40
Brightness
[0]
–30
+30
• When “OPC” is set to “On” or “On:Display”, an “Energy
Save” status icon appears to the left of “OPC” in the
“Picture” menu.
• When “OPC” is set to “Off”, an “Energy Save” status icon
appears to the left of “Backlight” in the “Picture” menu.
EXAMPLE
BBC1
ATV
01
PAL
I
NICAM
STEREO
Subtitle : Teletext Off
New Information
26
• Select “Off” to cancel the sleep timer.
• When the time has been set, countdown automatically
starts.
• Five minutes before the preset of time expires, the
remaining time displays each minute.
Basic adjustment
Channel Settings
Auto Installation
E Manual Adjust
Configure various settings for each service using the
Colour (R, G, B) buttons.
Service
No.
Setup
Auto Installation
The TV automatically detects and stores all available
services in your area. This function also allows you to
perform the channel setting for digital and analogue
individually and reconfigure the settings after the initial
auto installation has been completed.
After selecting “Yes” on the screen, you can set
language and channel search the same as in the
initial auto installation. Follow steps 2, 5 and 6
on page 9.
NOTE
• You cannot set the Home/Store setting and the country
setting in “Auto Installation” in the “Setup” menu. If you
want to reconfigure those settings, automatically execute
initial auto installation after executing “Reset” from the
“Setup” menu.
• The current country setting is displayed on the screen.
Digital channel settings
Setup
Programme Setup
Digital Setting
You can reconfigure the DTV service settings
automatically or manually.
E Additional Search
Use this menu to add new services automatically after
auto installation has been completed.
DTV
993
SIT 3
DTV
994
SIT 2
DTV
995
SIT 1
DTV
999
R
1
2
Service
Name
: Lock
Lock
CH
Skip
Old
LCN
✔
✔
HD Monosco
G
: CH Skip
: Sort
B
Press a/b to select the desired service.
Press the colour button on the remote control unit
corresponding with the item you want to reconfigure.
• The ✔ mark indicates the operation is set to on. Each
time the colour button is pressed, you can switch the
corresponding operation on/off.
Buttons for Manual Adjust operation
Lock: Press R button.
When the service is locked, you must enter your PIN
whenever you tune to the service.
CH Skip: Press G button.
Services with a ✔ mark are passed over when pressing
Pr/s on the TV or remote control unit.
Sort: Press B button.
The item position of services can be sorted.
1 Press a/b to select the service whose item
position you want to move, and then press OK.
DTV
994
SIT 2
DTV
995
SIT 1
✔
✔
2 Press a/b to move it to the desired position,
and then press OK.
DTV
994
SIT 1
DTV
995
SIT 2
✔
✔
3 Repeat steps 1 and 2 until all desired service
items are sorted.
E Manual Search
Add new services within a specified frequency band.
• Enter the frequency using 0–9 numeric buttons.
• You can perform “Manual Search” with a service number
only when the five Nordic countries have been selected in
the country setting.
27
Basic adjustment
Analogue channel settings
Setup
Programme Setup
Analogue Setting
Skip
Channels with “Skip” set to “On” are passed over
when using Pr/s even if selected while watching
the image from the TV.
Decoder
When connecting a decoder to the TV, you need to
select “EXT1” or “EXT2”.
You can reconfigure the analogue TV channels settings
automatically or manually.
NOTE
E Additional Search
Lock
You can block the viewing of any channel.
Use this menu to add new channels automatically after
auto installation has been made.
• Start searching channels after selecting the colour system.
E Manual Adjust
Use this menu to set up analogue TV channels
manually.
After selecting “Yes” on the screen, press a/b/
c/d to select the channel you want to set and
then press OK.
Fine
You can adjust the frequency to the desired position.
• The factory preset value is “Off”.
NOTE
• See “Child Lock” for setting a PIN.
• When “Lock” is set to “On” for a channel, “Child lock has
been activated” displays, and the image and sound of the
channel are blocked.
• When pressing 6 while “Child lock has been activated”
displays, the PIN input window will display. Inputting the
correct PIN unlocks the “Child Lock” temporarily until the
power is turned off.
E Sort
EXAMPLE
Channel positions can be sorted freely.
1 Press c/d to select “Yes”, and then press OK.
2 Press a/b/c/d to select the channel you want
to move, and then press OK.
3 Press a/b/c/d to move it to the desired
position, and then press OK.
4 Repeat steps 2 and 3 until all desired channels
are sorted.
• 179.25 MHz: Press 1 s 7 s 9 s 2 s 5.
• 49.25 MHz: Press 4 s 9 s 2 s 5 s OK.
E Erase Programme
Colour sys.
Select the optimum colour system to receive (“Auto”,
“PAL”, “SECAM”).
Channels can be erased individually.
1 Press c/d to select “Yes”, and then press OK.
2 Press a/b/c/d to select the channel you want
to erase, and then press OK.
Sound sys. (Broadcasting systems)
Select the optimum sound systems (Broadcasting
systems) to receive (“B/G”, “D/K”, “I”, “L/L’”).
3
NOTE
• Adjust while checking the background picture as a
reference.
• Instead of pressing c/d to adjust the frequency, you
can set by directly entering the frequency number of the
channel with 0–9 numeric buttons.
Label
When a TV channel sends its Network Name, the
“Auto Installation” detects the information and assigns
a name to it. However, you can change channel names
individually.
1 Press a/b/c/d to select each character of the
new name for the channel, and then press OK.
2 Repeat step 1 above until the name is fully spelt
out.
NOTE
• The name can be five characters or less.
• If a channel name is less than five characters, select “END”
to set the channel name.
28
• A message window pops up.
4
Press c/d to select “Yes”, and then press
OK to erase the selected channel. All the
subsequent channels move up.
Repeat steps 2 and 3 until all desired channels
are erased.
Basic adjustment
Password/Parental lock settings
Setup
Language Settings (language,
subtitle, multi audio)
Setup
Child Lock
Allows you to use a PIN to protect certain settings
from being accidentally changed.
Change PIN
Register a four-digit password number to use the
“Child Lock” function.
1 Enter the four-digit number as a PIN using 0–9
numeric buttons.
2 Enter the same four-digit number as in step 1 to confirm.
Language
You can select a OSD language from the “Setup”
menu. Select from among 23 languages (Czech,
Danish, Dutch, English, Estonian, Finnish, French,
German, Greek, Hungarian, Italian, Latvian, Lithuanian,
Norwegian, Polish, Portuguese, Russian, Slovak,
Slovene, Spanish, Swedish, Turkish, Ukrainian).
Digital Setup
• “The system PIN has been changed successfully” displays.
Subtitle
NOTE
• To view a locked channel, you must enter the PIN (See pages 27
and 28 for locking channels from viewing in DTV and ATV mode).
When you select a locked channel, a PIN prompt message pops
up. Press 6 to display the PIN input window.
Cancel PIN
Allows you to reset your PIN.
NOTE
• As a precautionary measure, make a note of your PIN on the
back of this operation manual, cut it out and keep it in a safe
place that children cannot reach.
Parental rating
Set up to two preferred subtitle languages (including
subtitles for the hearing impaired) to display if subtitles
are available.
Selectable items
E 1st Language E 2nd Language
E For hearing impaired
E Switching subtitle languages
Each time you press [ on the remote control unit, the
subtitle switches.
Off
This function allows DTV services to be restricted.
It prevents children from watching violent or sexual
scenes that may be harmful.
1st Language
••••••
2nd Language
NOTE
E Set “For hearing impaired” to “Yes”
• “Universal viewing” and “Parental approval pref.” are ratings used
exclusively in France.
• Refer to page 44 for details about ratings.
Subtitles for the hearing impaired have priority over
each of the subtitle language settings (Example: “1st
Language”, “2nd Language”, etc.).
Option
Key Lock
This function allows you to lock the buttons on the TV
or remote control unit in order to prohibit children from
changing the channel or volume.
Item
Off: Unlocks the buttons.
RC Control Lock: Locks all buttons on the remote control unit.
Button Control Lock: Locks the buttons on the TV except the
power switch.
NOTE
EXAMPLE
1st Language
(For hearing impaired)
1st Language
NOTE
• Subtitles will not be displayed when the service does not contain
subtitle information.
Option
Digital Audio Language
• You cannot set both “RC Control Lock” and “Button Control Lock”
at the same time.
Set up to three preferred multi audio languages to
display if the audio languages are available.
E Cancelling the lock
E Switching the multi audio languages
Press the MENU button on the TV and set to “Off” to
cancel the “RC Control Lock”. Press the MENU button
on the remote control unit and set to “Off” to cancel
the “Button Control Lock”.
Each time you press 2 on the remote control unit,
the audio language switches.
• Refer to page 23 for menu operation using the MENU button on
the TV.
29
Useful Viewing functions
Selecting the picture size
Selecting the WSS (Wide Screen
Signalling) picture size automatically
Selecting the picture size manually
You can select the picture size. Selectable picture size
varies with the type of signal received.
Item (for SD [Standard-Definition] signals)
Setup
WSS
The “WSS” allows the TV to switch automatically
among the different picture size.
NOTE
• Use “WIDE MODE” if an image does not switch to the
appropriate picture size. When the broadcast signal
contains no “WSS” information, the function will not work
even if enabled.
Normal: Keeps the original aspect ratio in a full screen
display.
Zoom 14:9: For 14:9 letterbox pictures. A thin side bar
appears on each side, and you may also see bars on
the top and bottom with some programmes.
Panorama: In this mode, the picture is stretched toward
each side of the screen. The picture may appear similar
to “Full” depending on broadcast signals.
Full: For 16:9 squeeze pictures.
Cinema 16:9: For 16:9 letterbox pictures. Bars may
appear on the top and bottom with some programmes.
Cinema 14:9: For 14:9 letterbox pictures. Bars may
appear on the top and bottom with some programmes.
Selecting the WSS (Wide Screen
Signalling) picture size manually
Setup
4:3 Mode
The “WSS” signal has 4:3 auto-switching that allows
you to select between “Normal” and “Panorama”.
Item (for HD [High-Definition] signals)
Full: Displays with an Overscan image. Crops all sides of
screen.
Underscan: Displays with an Underscan image only
when receiving a 720p signal. Displays with the HighDefinition image adjusted optimally. Noise may appear
on the edge of the screen with some programmes.
Dot by Dot: Displays an image with the same number
of pixels on the screen when receiving 1080i/1080p
signals only.
Item
Normal: Normal range keeping 4:3 or 16:9 aspect ratio.
Panorama: Wide image without side bars.
WSS signal 4:3 screen
4:3 mode “Normal”
NOTE
• Some items do not appear depending on the type of
received signal.
1
Press f.
• The “WIDE MODE” menu displays.
• The menu lists the “WIDE MODE” options selectable
for the type of video signal currently received.
4:3 mode “Panorama”
2
Press f or a/b while the “WIDE MODE”
menu displays on the screen.
• As you toggle the options, each is immediately
reflected on the screen. There is no need to press OK.
Basically, if you set “WSS” to “On” in the “Setup”
menu, the optimum “WIDE MODE” is automatically
chosen for every broadcast, VCR or DVD player/
recorder.
NOTE
• Even if you select your desired “WIDE MODE” manually,
the TV may automatically switch to the optimum “WIDE
MODE” depending on the signal received when “WSS” is
set to “On”.
30
Useful Viewing functions
Selecting the recording picture
size manually
Automatic volume adjustment
Option
Digital Setup
Auto Volume
REC Picture Size
You can use this menu to set the appropriate picture
size for viewing a 16:9 format TV programme on a 4:3
TV.
Different sound sources sometimes do not have the
same volume level, such as a programme and its
commercial breaks. The Automatic Volume Control
(Auto Volume) reduces this problem by equalizing
levels.
Emphasising dialogue
Option
Clear Voice
This function emphasises speech against background
noise for greater clarity. It is not recommended for
music sources.
Outputting audio only
Setting to “4:3 TV”
Setting to “16:9 TV”
Option
NOTE
• This function must be set before recording.
Selecting the HDMI picture size
automatically
Setup
HDMI Auto View
Audio Only
When listening to music from a music programme, you
can set the TV off and enjoy audio only.
Item
Off: Both screen images and audio are output.
On: Audio is output without a screen image.
This function allows you to automatically change to the
appropriate picture size when viewing an HDMI signal
using the HDMI1, 2 and 3 terminals.
Other picture and audio settings
Adjusting image position
Setup
Position
For adjusting a picture’s horizontal and vertical
position.
Item
H-Pos.: Centres the image by moving it to the left or
right.
V-Pos.: Centres the image by moving it up or down.
NOTE
• Adjustments are stored separately for each input source.
• Depending on the input signal type or “WIDE MODE”
setting, a position setting may not be available.
• This function is not available for DTV broadcasts with
MHEG signals.
31
Useful Viewing functions
Display Settings
Time and Title display
Channel display
Option
Time Display
You can display the channel information by pressing
p on the remote control unit.
DTV Mode
ATV Mode
DTV
001
Audio (ENG) : STEREO
Video : 1080i
Subtitle : ENG 1/3
New Information
Time Display
BBC1
BBC2
ATV
01
PAL
I
NICAM
STEREO
Subtitle : Teletext Off
New Information
* Four digit numbers (e.g. 0001) are displayed after
selecting the five Nordic countries in the country
setting.
E Time display in channel information
You can display the time information included in DTV
and teletext broadcasts.
This function allows you to display the clock time in the
lower-right corner of the screen.
Item
On: Displays the clock time.
On (half-hourly): Displays the clock time in 30-minute
increments.
Off: Hides the clock time.
Time Format
You can select the time format (either “24HR” or “AM/
PM”) for the clock time.
NOTE
Option
• Skip step 1 if receiving DTV broadcasts.
1
2
3
4
Select a TV channel (The time information is
automatically captured).
Press p. The channel display will appear on
the TV.
Press p again within the several seconds
that the channel display is on the screen. Time
information will be shown in the lower-right
corner of the screen for several seconds.
Even when you change the TV channel, you can
display the time information with steps 2 and 3
above.
NOTE
Game Play Time
This function allows you to display the elapsed time on
the screen when “AV MODE” is set to “GAME”.
Item
On: Under connecting a game console to the TV, the
elapsed time is displayed in 30-minute increments after
you start playing a game.
Off: Hides the time.
NOTE
• This menu is not selectable if the input source is “TV” or
“USB”.
• If acquired successfully, the time information will appear in
the upper-right corner of the screen by pressing MENU.
Option
Programme Title Display
This function allows you to display programme
information such as the title and airtime by tuning a
channel.
NOTE
• This function is available only when the DTV mode is
selected.
32
Other useful features
Setting when using external
devices
Skipping specified inputs
Setup
Input source settings
Option
Input Select
For setting the signal type of external equipment.
Input Skip
This setting allows you to skip the SCART, HDMI or
RGB input on the Input Source Selection operation.
EXT1 (SCART)
EXT2 (SCART)
Item
EXT4 (RGB)
HDMI1
EXT1: Y/C, CVBS, RGB
EXT2: Y/C, CVBS, RGB
HDMI2
Yes
No
HDMI3
NOTE
• If no (colour) image displays, try changing to another
signal type.
• Check the operation manual of the external equipment for
the signal type.
Colour system settings
Setup
Option
Input Label
Colour System
You can label each input source with a custom
description.
1 Press b to select the desired input source.
2 Go to “MENU” > “Setup” > “Input Label”.
3 Press a/b/c/d to select each character of the
new name for the input source, and then press
OK.
You can change the colour system to one that is
compatible with the image on the screen.
NOTE
• The factory preset value is “Auto”.
• If “Auto” is selected, the colour system for each channel
is automatically set. If an image does not display clearly,
select another colour system (e.g. “PAL”, “SECAM”).
Additional features
DVD
A
K
U
0
4
B
L
V
1
C
M
W
2
D
N
X
3
E
O
Y
4
F
P
Z
5
G
Q
+
6
H I J CLEAR
R S T BACK
– . _
7 8 9 END
Repeat until the label is fully spelt out.
Setup
Quick Start
You can reduce the TV’s start-up time after turning on
the power with the remote control unit.
Item
NOTE
• The label can be six characters or less.
• When you want to set an input source label of less than six
characters, select “END” to set the name.
On: The TV quickly starts up from standby. 30 W or more
of power consumption is required during standby.
Off: Power consumption is small during standby.
INPUT SOURCE
TV
EXT1
EXT2
DVD
EXT4
HDMI1
EXT6
NOTE
• You cannot change labels if the input source is “TV” or
“USB”.
33
Other useful features
Connecting a USB device
Photo Mode
Connect an USB device to the TV as shown below.
Viewing thumbnails
Sample
• Depending on the USB device, the TV may not be able to
recognise the contained data.
• Use only alphanumeric characters for naming files.
• File names over 80 characters (may vary depending on
character set) may not be displayed.
• Do not disconnect a USB device or memory card from the
TV while transferring files, using the slide show function,
when a screen is switching to another or before you exit
“USB” from the “INPUT SOURCE” menu.
• Do not connect and disconnect a USB device from the TV
repeatedly.
Demo/Demo 01
Demo.jpg
2007:10:18 13:30:00
600KB
1600X1200
Buttons for thumbnail operations
Buttons
OK
When selecting the folder icon with the
6 mark: Go back to the parent directory.
When selecting a folder icon: Enter this
directory.
When selecting a photo thumbnail:
Display the photo in full screen.
a/b/c/d
(Cursor)
Select a desired item.
6
Return to the top menu.
EXT2
R button
Go back to the previous page.
EXT3
G button
Go to the next page.
Y button
Select BGM for the slide show.
B button
Start the slide show.
USB Photo Viewer/Music Player
In this mode, you can enjoy viewing
photos and listening to music from
external USB devices. Select “USB”
from the “INPUT SOURCE” menu to
enter this mode.
INPUT SOURCE
TV
EXT1
EXT4
NOTE
HDMI1
• You cannot enter this mode when there
HDMI2
is no USB device connected to the TV.
HDMI3
• This mode is not available during DTV
EXT8
timer recording.
• “WIDE MODE” is fixed during this
USB
mode.
• “USER (USB)” is the default value for the “AV MODE”
setting. Each time you press AV MODE, the mode changes
between “USER (USB)”, “DYNAMIC (Fixed)”, “DYNAMIC”
and “STANDARD”.
Selecting modes and devices
NOTE
• When there are invalid photo files, the g mark will be
displayed for the file.
• You can see the file name, shooting date, file size and
pixel size of the selected photo in the lower-left corner of
the screen (shooting date is only available in the EXIF file
format).
Viewing photos in full screen
Select Mode
Buttons for full screen display operation
Buttons
Photo Mode
Music Mode
Select USB drive
1
2
Description
Drive 1
Drive 2
Drive 3
Drive 4
Drive 5
Drive 6
Drive 7
Drive 8
Drive 9
Drive 10
Drive 11
Drive 12
Drive 13
Drive 14
Drive 15
Drive 16
Press c/d to select between “Photo Mode”
and “Music Mode”, and then press OK.
Press a/b/c/d to select the drive where you
want to find your files, and then press OK.
Description
c/d (Cursor)
Go to the previous/next photo in the
same directory.
6
Return to the thumbnail selection screen.
R button
Rotate the photo by 90 degrees to the
left.
G button
Rotate the photo by 90 degrees to the
right.
B button
Reveal/hide the Guide Display.
NOTE
NOTE
• You do not need to select the drive in step 2 when there is
only one drive in the connected USB device.
• 16 is the maximum number of drives that can be displayed.
• Rotating photos only applies to the temporarily selected
item and this setting is not saved.
34
Other useful features
Music Mode
Slide show
E Selecting the BGM
File name
Demo/Demo1
SONGS
CLASSIC
SONG_01.MP3
SONG_02.MP3
SONG_03.MP3
SONG_04.MP3
SONG_05.MP3
SONG_06.MP3
SONG_07.MP3
SONG_08.MP3
SONG_09.MP3
Playing:
SONG_02.MP3
Slide Show BGM:
SONG_03.MP3
Time
3:05
3:15
3:02
6:05
4:52
0:00
3:13
3:23
3:33
1:00 / 3:15
OK
3:05
3:15
3:02
6:05
4:52
0:00
3:13
3:23
3:33
1:00 / 3:15
Description
OK
When selecting the folder icon with the
6 mark: Go back to the parent directory.
When selecting a folder icon: Enter this
directory.
When selecting a music file: Play music.
a/b (Cursor)
Select the desired item.
c (Cursor)
Page up.
d (Cursor)
Page down.
6
Return to the top menu.
R button
Stop music.
Description
When selecting the folder icon with the
6 mark: Go back to the parent directory.
When selecting a folder icon: Enter this
directory.
When selecting a music file: Play music.
Time
Buttons for Music Mode
Buttons
Buttons for slide show BGM select
operation
Buttons
File name
Demo/Demo1
ROOT
CLASSIC
SONG_01.MP3
SONG_02.MP3
SONG_03.MP3
SONG_04.MP3
SONG_05.MP3
SONG_06.MP3
SONG_07.MP3
SONG_08.MP3
SONG_09.MP3
Playing:
SONG_02.MP3
a/b (Cursor)
Select a desired item.
c (Cursor)
Page up.
d (Cursor)
Page down.
G button
Play/Pause music.
6
Return to the thumbnail selection screen.
B button
R button
Stop music.
Turn off the screen image for audio only
output.
G button
Play/Pause music.
Y button
Set the selected music to the slide show
BGM.
B button
Reset the slide show BGM.
NOTE
• Only one song can be set to the slide show BGM.
• Slide show BGM will be reset in the cases below.
• Go back to the top menu.
• Change the “INPUT SOURCE”.
• When there are invalid music files, the g mark will be
displayed for the file.
• The displayed play time may differ slightly from the actual
play time depending on the files.
E Slide show
NOTE
• When there are invalid music files, the g mark will be
displayed for the file.
• The displayed play time may differ slightly from the actual
play time depending on the files.
USB device compatibility
USB device
USB Memory, USB card reader (Mass
Storage class)
File system
FAT/FAT32
Photo file
format
JPEG (.jpg) (DCF2.0 compliant)
Music file
format
MP3 (.mp3)
Bitrate: 32k, 40k, 48k, 56k, 64k, 80k,
96k, 112k, 128k, 160k, 192k, 224k,
256k, 320kbps
Sampling frequency: 32k, 44.1k, 48kHz
Buttons for slide show operation
Buttons
Description
6
Return to the thumbnail selection screen.
B button
Reveal/hide the Guide Display.
NOTE
NOTE
• Progressive format jpeg files are not supported.
• Music files in USB 1.1 devices may not be played properly.
• Operation using USB hubs is not guaranteed.
• The selected BGM is played repeatedly.
• The slide show continues until you press 6.
• The slide show speed is approximately 10 seconds per
photo.
35
Connecting a PC
Connecting a PC
Setting audio input
HDMI Connection
Option
HDMI-certified cable
PC
PC Audio Select
HDMI1, 2* or 3
PC
ø 3.5 mm stereo minijack cable
When using the EXT4 terminal or HDMI2 terminal, you must
select which terminal uses the AUDIO (R/L) jack for analogue
audio input.
HDMI2*
NOTE
DVI/HDMI cable
* When using the HDMI2 terminal, you must select the proper item in
the “PC Audio Select” menu depending on the type of HDMI cable
connected (Refer to the right column for details).
• You must set this to “EXT4 (RGB)” when connecting
devices (including a PC) with an HDMI-certified cable to the
HDMI2 terminal. If “HDMI2” is set, there will be no sound
output.
Displaying a PC image on the
screen
Analogue Connection
RGB cable
PC
Item
HDMI2: When connecting devices (including a PC) with DVI/HDMI
cable to the HDMI2 terminal and inputting analogue audio
signals from the AUDIO (R/L) jack.
EXT4 (RGB): When connecting a PC to the EXT4 terminal, and
inputting analogue audio signals from the AUDIO (R/L) jack.
Selecting the picture size
EXT4*
You can select the picture size.
1 Press f.
• The “WIDE MODE” menu displays.
2
Press f or a/b to select a desired item on the
menu.
NOTE
• Connect the PC before making adjustments.
• Selectable picture size may vary with input signal type.
ø 3.5 mm stereo minijack cable
EXAMPLE
DVI/RGB conversion cable
PC
EXT4*
Normal
Full
Item
ø 3.5 mm stereo minijack cable
* When using the EXT4 terminal, you must select “EXT4 (RGB)” in the
“PC Audio Select” menu (Refer to the right column for details).
NOTE
• The PC input terminals are DDC1/2B-compatible.
• Refer to page 39 for a list of PC signals compatible with the TV.
• A Macintosh adaptor may be required for use with some Macintosh
computers.
• When connecting to a PC, the input signal type is automatically
detected except 1,024 g 768 and 1,360 g 768 signals.
36
Full: An image fully fills the screen.
Cinema: For letterbox pictures. Bars may appear on the
top and bottom with some programmes.
Normal: Keeps the original aspect ratio in a full screen
display.
Dot by Dot: Displays an image with the same number of
pixels on the screen.
NOTE
• Refer to page 30 for AV signals (See below).
HDMI: 480i/480p/576i/576p/720p/1080i/1080p
ANALOGUE RGB: 576p/720p (50Hz)/1080i
• The ANALOGUE RGB terminal (PC) (EXT4) is not
compatible with 480i/576i/1080p signals.
Connecting a PC
Item
Adjusting the PC image
automatically
This function enables the screen to be automatically
adjusted to its best possible condition when the
analogue terminals of the TV and PC are connected
with a commercially available DVI/RGB conversion
cable, etc.
H-Pos.: Centres the image by moving it to the left or
right.
V-Pos.: Centres the image by moving it up or down.
Clock: Adjusts when the image flickers with vertical
stripes.
Phase: Adjusts when characters have low contrast or
when the image flickers.
NOTE
Setup
• For resetting all adjustment items to the factory preset
values, press a/b to select “Reset”, and then press OK.
• “Clock” and “Phase” in the “Fine Sync.” menu can be
adjusted only when inputting analogue signals through the
EXT4 terminal.
Auto Sync.
30%
NOTE
• When “Auto Sync.” is successful, “Auto Sync completed
successfully” displays. If not, “Auto Sync.” failed.
• “Auto Sync.” may fail even if “Auto Sync completed
successfully” displays.
• “Auto Sync.” may fail if the PC image has low resolution,
has unclear (black) edges, or is moved while executing
“Auto Sync.”.
• Be sure to connect the PC to the TV and switch it on
before starting “Auto Sync.”.
• “Auto Sync.” can be executed only when inputting
analogue signals through the EXT4 terminal.
Selecting input resolution
• Some input signals may have to be registered
manually to display properly.
• The pairs of input signals (resolutions) in the list
below are not distinguishable when received. In such
cases, you have to set the correct signal manually.
After setting once, it will display when the same
signal (resolution) is input again.
Setup
Input Signal
1024 x 768
Adjusting the PC image manually
1360 x 768
Ordinarily you can easily adjust the picture as
necessary to change image position using “Auto
Sync.”. In some cases, however, manual adjustment is
needed to optimise the image.
1
2
(Example)
Setup
NOTE
Fine Sync.
• You can only select the “Input Signal” on the “Setup” menu
when receiving one of the two input signals listed above.
Press a/b to select the specific adjustment
item.
Press c/d to adjust the item to the desired
position.
H-Pos.
[ 90]
a
b
V-Pos.
[ 39]
a
b
Clock
[ 90]
a
b
Phase
[ 20]
a
b
Reset
37
Connecting a PC
RS-232C port specifications
PC Control of the TV
• When a programme is set, the TV can be controlled
from the PC using the RS-232C terminal. The input
signal (PC/video) can be selected, the volume
can be adjusted and various other adjustments
and settings can be made, enabling automatic
programmed playing.
• Use an RS-232C serial control cable (cross type)
(commercially available) for the connections.
Parameter
Input the parameter values, aligning left, and fill with
blank(s) for the remainder (Be sure that four values are
input for the parameter).
When the input parameter is not within an adjustable
range, “ERR” returns (Refer to “Response code
format”).
0
0
0
0
NOTE
–
3
0
• This operation system should be used by a person who is
accustomed to using PCs.
1
0
0
0
0
5
?
Communication conditions
Set the RS-232C communications settings on the PC
to match the TV’s communications conditions. The
TV’s communications settings are as follows:
9,600 bps
Data length:
8 bits
Parity bit:
None
Stop bit:
1 bit
Flow control:
None
?
?
?
Normal response
O
K
Return code (0DH)
Send the control commands from the PC via the RS232C connector.
The TV operates according to the received command
and sends a response message to the PC.
Do not send multiple commands at the same time.
Wait until the PC receives the OK response before
sending the next command.
Make sure to send “A” with the carriage return and
confirm that “ERR” returns before operating.
Command format
Eight ASCII codes eCR
C1 C2 C3 C4 P1 P2 P3
Parameter
four digits
P4
Return code
Command four digits: Command. The text of four
characters.
Parameter four digits: Parameter 0–9, blank, ?, minus
38
?
Response code format
Communication procedure
Command
four digits
5
When “?” is input for some commands, the present
setting value responds.
RS-232C serial control cable
(cross type)
Baud rate:
9
Problem response (communication error or incorrect
command)
E
R
R
Return code (0DH)
After sending the return code (0DH), make sure to
send the line feed (0AH) as well.
Connecting a PC
PC compatibility chart
Resolution
Horizontal
Frequency
Vertical
Frequency
Analogue (DSub)
Digital (HDMI)
VESA
Standard
VGA
640 g 480
31.5 kHz
60 Hz
✔
✔
✔
SVGA
800 g 600
37.9 kHz
60 Hz
✔
✔
✔
XGA
1,024 g 768
48.4 kHz
60 Hz
✔
✔
✔
WXGA
1,360 g 768
47.7 kHz
60 Hz
✔
✔
✔
SXGA
1,280 g 1,024
64.0 kHz
60 Hz
✔
✔
✔
SXGA+
1,400 g 1,050
65.3 kHz
60 Hz
✔
✔
VGA, SVGA, XGA, WXGA, SXGA and SXGA+ are
registered trademarks of International Business
Machines Corporation.
NOTE
• This TV has only limited PC compatibility, correct operation
can only be guaranteed if the video card conforms exactly
to the VESA 60 Hz standard. Any variations from this
standard will result in picture distortions.
RS-232C command list
CONTROL ITEM
COMMAND
PARAMETER
CONTROL CONTENTS
CONTROL ITEM
_
_
_
POWER OFF
INPUT SELECTION A
I
T G D
_
_
_
_
INPUT SWITCHING (TOGGLE)
V
P O S
*
*
*
_
V-POSITION (AV/PC)
I
T
V D
_
_
_
_
TV (CHANNEL FIXED)
C
L
*
*
*
_
CLOCK (0–180)
I
D
T
V
_
_
_
_
DTV (CHANNEL FIXED)
PHASE (0–40)
I
A
V D
*
_
_
_
EXT1–4, 8 (1–4, 8), HDMI1–3
(5–7)
D C C H
*
*
_
_
TV DIRECT CHANNEL (1–99)
_
_
_
_
CHANNEL UP
C H D W _
_
_
_
CHANNEL DOWN
D
*
*
_
THREE DIGIT DTV DIRECT
CHANNEL (1–999) (Non-Nordic
countries)
D
INPUT SELECTION B
T
V D
V D
*
*
*
*
*
T
U P
_
_
_
_
DTV CHANNEL UP
D
T
D W _
_
_
_
DTV CHANNEL DOWN
I
N P
_
_
_
EXT1 (Y/C)
1
0
I
N P
1
1
_
_
_
EXT1 (CVBS)
I
N P
1
2
_
_
_
EXT1 (RGB)
I
N P
2
0
_
_
_
EXT2 (Y/C)
I
N P
2
1
_
_
_
EXT2 (CVBS)
I
N P
2
2
_
_
_
EXT2 (RGB)
V M D
0
_
_
_
TOGGLE
A
V M D
1
_
_
_
STANDARD
A
V M D
2
_
_
_
MOVIE
A
V M D
3
_
_
_
GAME
A
V M D
4
_
_
_
USER
A
V M D
5
_
_
_
DYNAMIC (Fixed)
A
V M D
6
_
_
_
DYNAMIC
A
V M D
7
_
_
_
PC
A
V M D
8
_
_
_
x.v.Colour
A
P H S
WIDE MODE
FOUR DIGIT DTV DIRECT
CHANNEL (1–9999) (Nordic
countries only)
D
AV MODE SELECTION A
VOLUME
T
V M D
?
?
?
?
1–8
V O L M
*
*
_
_
VOLUME (0–60)
C K
MUTE
SURROUND
AUDIO CHANGE
SLEEP TIMER
TEXT
*
*
*
_
CONTROL CONTENTS
0
C H U P
H P O S
PARAMETER
P O W R
CHANNEL
POSITION
COMMAND
POWER SETTING
H-POSITION (AV/PC)
E
*
*
_
_
W
I
D E
0
_
_
_
TOGGLE (AV)
W
I
D E
1
_
_
_
NORMAL (AV)
W
I
D E
2
_
_
_
ZOOM 14:9 (AV)
W
I
D E
3
_
_
_
PANORAMA (AV)
W
I
D E
4
_
_
_
FULL (AV)
W
I
D E
5
_
_
_
CINEMA 16:9 (AV)
W
I
D E
6
_
_
_
CINEMA 14:9 (AV)
W
I
D E
7
_
_
_
NORMAL (PC)
W
I
D E
8
_
_
_
CINEMA (PC)
W
I
D E
9
_
_
_
FULL (PC)
W
I
D E
1
0
_
_
DOT by DOT (AV/PC)
W
I
D E
1
1
_
_
UNDERSCAN (AV)
M U
T
E
0
_
_
_
TOGGLE
M U
T
E
1
_
_
_
MUTE ON
M U
T
E
2
_
_
_
MUTE OFF
A C S U
0
_
_
_
SURROUND TOGGLE
A C S U
1
_
_
_
SURROUND ON
A C S U
2
_
_
_
SURROUND OFF
A C H A
_
_
_
_
TOGGLE
O F
T M 0
_
_
_
OFF
O F
T M 1
_
_
_
SLEEP TIMER 30 MIN
O F
T M 2
_
_
_
SLEEP TIMER 1 HOUR
O F
T M 3
_
_
_
SLEEP TIMER 1 HOUR 30 MIN
O F
T M 4
_
_
_
SLEEP TIMER 2 HOUR
O F
T M 5
_
_
_
SLEEP TIMER 2 HOUR 30 MIN
T
E
X
T
0
_
_
_
TEXT OFF
T
E
X
T
1
_
_
_
TEXT ON (TOGGLE)
D C P G
*
*
*
_
DIRECT PAGE JUMP (100–899)
39
Appendix
Troubleshooting
Problem
Possible Solution
• No power.
• Check if you pressed B on the remote control unit.
If the indicator on the TV lights up red, press B.
• Is the AC cord disconnected?
• Check if you pressed a on the TV.
• The TV cannot be operated.
• External influences such as lightning, static electricity, etc., may cause improper operation. In this
case, operate the TV after first turning off the power, or unplugging the AC cord and re-plugging
it in after one or two minutes.
• Remote control unit does not operate.
•
•
•
•
• Picture is cut off.
• Is the image position correct?
• Are screen mode adjustments (WIDE MODE) such as picture size made correctly? (Pages 30
and 36)
• Strange colour, light colour, or dark
colour, or colour misalignment.
• Adjust the picture tone.
• Is the room too bright? The picture may look dark in a room that is too bright.
• Check the “Colour System” setting (Pages 28 and 33).
• Power is suddenly turned off.
• The TV’s internal temperature has increased.
Remove any objects blocking the vent or clean.
• Is the “Sleep Timer” set? Select “Off” from the “Sleep Timer” menu (Page 26).
• Is “No Signal Off” or “No Operation Off” activated?
• No picture.
•
•
•
•
•
•
•
Are connections to external equipment correct? (Pages 15–17)
Is the input signal type selected correctly after connection? (Page 33)
Is the correct input source selected? (Page 10)
Is a non-compatible signal being input? (Page 39)
Is the picture adjustment correct? (Pages 24–25)
Is the antenna connected properly? (Page 8)
Is “On” selected in “Audio Only”? (Page 31)
• No sound.
•
•
•
•
Is the volume too low?
Make sure that headphones are not connected.
Check if you pressed e on the remote control unit.
Is the proper item selected in the “PC Audio Select” menu when connecting devices to the
HDMI2 terminal or the EXT4 terminal? (Pages 16 and 36)
• The TV sometimes makes a cracking
sound.
• This is not a malfunction. This happens when the cabinet slightly expands and contracts
according to changes in temperature. This does not affect the TV’s performance.
Are batteries inserted with polarity (e, f) aligned?
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminating to the remote control sensor?
Cautions regarding use in high and low temperature environments
• When the TV is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the TV will recover when the temperature returns to normal.
• Do not leave the TV in a hot or cold location. Also, do not leave the TV in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: e5 °C to e35 °C.
Information on the software license for this product
Software composition
The software included in this product is comprised of various software components whose individual copyrights are held by
SHARP or by third parties.
Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that were developed
or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant
laws. This product also makes use of freely distributed software and software components whose copyrights are held by
third parties. These include software components covered by a GNU General Public License (hereafter GPL), a GNU Lesser
General Public License (hereafter LGPL) or other license agreement.
Obtaining source code
Some of the open source software licensors require the distributor to provide the source code with the executable software
components. GPL and LGPL include similar requirements. For information on obtaining the source code for the open source
software and for obtaining the GPL, LGPL, and other license agreement information, visit the following website:
http://www.sharp-eu.com/gpl/
We are unable to answer any questions about the source code for the open source software. The source code for the
software components whose copyrights are held by SHARP is not distributed.
Acknowledgements
The following open source software components are included in this product:
• linux kernel • busy box • uClibc • zlib • libpng • libjpeg
40
Appendix
Updating your TV via DVB-T
Ensure that your TV software version is always up to
date. From time to time SHARP will make updated TV
base software and DVB software available.
Digital Setup
Download Setup
Searching for updates*
Information
Receiver Report
Display reports regarding failures and changes for
timer settings.
Reset
If complex adjustments are made so that the settings
cannot be restored to normal, you can reset the
settings to the factory preset values.
* All countries except UK and Sweden are set to “No”
for this function.
The TV automatically determines whether a new
software version is available when the TV is in standby
mode.
Item
Yes: Automatically searches for new software updates
available when the TV is in standby mode.
No: Does not search for update information.
Now: Checks if there is new software immediately.
Setup
Reset
1
2
Go to “MENU” > “Setup” > “Reset”.
Press c/d to select “Yes”, and then press OK.
• “Now, TV will restart automatically. OK?” displays on
the screen.
3
Press c/d to select “Yes”, and then press OK.
• “Now initialising...” displays on the screen and blinks.
• After the reset has completed, the power shuts
off and then comes back on. The screen will have
returned to its original settings.
Downloading the software
You can select the method of update.
1 If the software is updated, the confirmation
message “New download information has been
detected.” appears.
• If the TV receives the update service while in standby
mode, a confirmation message displays after turning
on the power.
2
Now initialising...
Follow the screen prompts.
Item
Yes: Starts downloading immediately. It takes
approximately one hour to update. You cannot carry
out other operations while downloading.
• Cancels the download by pressing OK on the remote
control unit when “Discontinue” is displayed on the
screen during the update.
No: Starts downloading automatically several minutes
after entering standby mode.
NOTE
• The TV must remain in standby mode for download. Do not
turn off the power using a on the TV.
• Updating the software may take some time.
Information
Identification
Setup
Identification
You can check the TV ID on the screen for reporting to
customer service.
CLEARING THE PIN
1
2
Go to “MENU” > “Setup”.
Press a/b to select “Auto Installation”,
“Programme Setup”, “Child Lock” or “Reset”,
and then press OK. The PIN input window will
display.
3
Press and hold both Pr and ik on the TV
simultaneously until the message appears on
the screen.
Message List
When new software is detected, you can confirm the
update information and download the software from
“Message List”.
NOTE
• When the TV succeeds at downloading new software,
the message is updated in the “Message List” of the
“Information” menu.
• The software update will not be carried out if there is no
new software available at the specified download time.
41
Appendix
Specifications
46o LCD COLOUR TV,
Model: LC-46D65E, LC-46DH65E,
LC-46DH65S
52o LCD COLOUR TV,
Model: LC-52D65E, LC-52DH65E,
LC-52DH65S
LCD panel
46o Advanced Super View & BLACK TFT LCD
52o Advanced Super View & BLACK TFT LCD
Resolution
2,073,600 pixels (1,920 g 1,080)
Item
Video Colour System
TV Function
TV-Standard
Receiving
Channel
PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
Analogue
CCIR (B/G, I, D/K, L/L’)
Digital
DVB-T (2K/8K OFDM)
VHF/UHF
E2–E69 ch, F2–F10 ch, I21–I69 ch, IR A–IR J ch (Digital: IR A ch–E69 ch)
CATV
Hyper-band, S1–S41 ch
TV-Tuning System
STEREO/BILINGUAL
Auto Preset 999 ch: non-Nordic / 9999 ch: Nordic (ATV: 99 ch), Auto Label, Auto Sort
NICAM/A2
Brightness
450 cd/m2
Backlight life
60,000 hours (when “Backlight” is set to the default position)
Viewing angles
H: 176°, V: 176°
Audio amplifier
10 W g 2
(40 mm g 110 mm) g 2
Speaker
Terminals
Antenna
UHF/VHF 75 q Din type (Analogue & Digital)
RS-232C
D-Sub 9 pin male connector
EXT1
SCART (AV input, Y/C input, RGB input, TV output)
EXT2
SCART (AV input/monitor output, Y/C input, AV Link, RGB input)
EXT3
COMPONENT IN: Y/PB(CB)/PR(CR), RCA pin (AUDIO R/L)
EXT4
15 pin mini D-sub, Ø 3.5 mm jack*
HDMI1 (EXT5)
HDMI
HDMI2 (EXT6)
HDMI, Ø 3.5 mm jack*
HDMI3 (EXT7)
HDMI
EXT8
RCA pin (AV input)
USB
USB 2.0
DIGITAL AUDIO OUTPUT
Optical S/PDIF Digital audio output
C. I. (Common Interface)
EN50221, R206001
OUTPUT
RCA pin (AUDIO R/L)
Headphones
Ø 3.5 mm jack (Audio output)
OSD language
Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian,
Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish,
Swedish, Turkish, Ukrainian
Power Requirement
AC 220–240 V, 50 Hz
Power Consumption
(Method IEC62087)
LC-46D65E
217 W (0.5 W Standby) LC-52D65E
266 W (0.5 W Standby)
LC-46DH65E
LC-46DH65S
220 W (0.5 W Standby) LC-52DH65E
LC-52DH65S
269 W (0.5 W Standby)
Weight
21.2 kg (Without stand), 24.2 kg (With stand)
Operating temperature
0 °C to e40 °C
24.7 kg (Without stand), 28.3 kg (With stand)
* The HDMI2 and EXT4 terminals can both use the same audio input terminal.
• As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
NOTE
• Refer to the inside back cover for dimensional drawings.
Optional accessory
The listed optional accessories are available for this LCD
colour TV. Please purchase them at your nearest shop.
• Additional optional accessories may be available in the near
future. When purchasing, please read the newest catalogue for
compatibility and check the availability.
42
No.
1
Part name
Wall mount bracket
(LC-46D65E, LC-46DH65E,
LC-46DH65S, LC-52D65E,
LC-52DH65E, LC-52DH65S)
Part number
AN-52AG4
End of life disposal
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!
Attention: Your product
is marked with this
symbol. It means that
used electrical and
electronic products
should not be mixed
with general household
waste. There is a
separate collection
system for these
products.
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires
proper treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used
electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local
retailer may also take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately
beforehand according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery
and recycling and thus prevent potential negative effects on the environment and human health which could otherwise
arise due to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for
the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local
collection facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used
products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
Information on Battery Disposal
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste!
There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with
legislation. Please contact your local authority for details on the collection and recycling schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method of disposal of the used battery.
43
Rating table for Child Lock
Broadcasted
rating
Useradjusted rating
AGE
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Universal viewing
✔
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Parental approval pref.
✔
✔
✔
✔
✔
—
—
—
—
—
—
—
—
—
—
X-rated
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Broadcasted
rating
Universal viewing
Parental approval pref.
X-rated
Universal viewing
—
—
—
Parental approval pref.
✔
—
—
X-rated
✔
✔
—
Useradjusted rating
44
(
) : LC-46D65E/46DH65E/46DH65S
[
] : LC-52D65E/52DH65E/52DH65S
: LC-46D65E/46DH65E/46DH65S
LC-52D65E/52DH65E/52DH65S
550.0
550,0
(1113.0 )/ [1252.0 ]
(1113,0 )/ [1252,0 ]
(106.6 )
(106,6 )
[111.9 ]
[111,9 ]
(101.4 )
(101,4 )
[95.6 ]
[95,6 ]
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
or )5) and of the same rating as above,
which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains
plug and fit an appropriate type.
(174.3 )
(174,3 )
[145.0 ]
[145,0 ]
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
400.0
400,0
(429.0 )/ [476.0 ]
(429,0 )/ [476,0 ]
(575.6 )/ [651.0 ]
(575,6 )/ [651,0 ]
400.0
400,0
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a
safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric
shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
295.0
295,0
(52.0 )
(52,0 )
[54.5 ]
[54,5 ]
SPECIAL NOTE FOR USERS IN THE U.K.
(704.0 )/ [796.0 ]
(704,0 )/ [796,0 ]
(756.0 )/ [851.0 ]
(756,0 )/ [851,0 ]
(1023.4 )/ [1157.0 ]
(1023,4 )/ [1157,0 ]
Printed in Spain
Gedruckt in Spanien
Imprimé en Espagne
Stampato in Spagna
Gedrukt in Spanje
Impreso en España
Impresso no Espanha
PIN
TÉLÉVISEUR COULEUR À ÉCRAN
CRISTAUX LIQUIDES (LCD)
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
TELEVISOR DE CRISTAL LÍQUIDO
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
: LC-46D65E/LC-52D65E
: LC-46DH65E/LC-52DH65E
: LC-46DH65S/LC-52DH65S
TINS-D808WJZZ
1
08P09-SP-NG
LCD-FARBFERNSEHGERÄT
NEDERLANDS
OPERATION MANUAL / BEDIENUNGSANLEITUNG / MODE D’EMPLOI / MANUALE DI ISTRUZIONI / GEBRUIKSAANWIJZING / MANUAL DE MANEJO /
MANUAL DE OPERAÇÃO
SHARP CORPORATION
LCD COLOUR TELEVISION
ESPAÑOL
D808WJZZ
Polígono Industrial Can Sant Joan
Calle Sena s/n
08174 SANT CUGAT DEL VALLÉS
BARCELONA (ESPAÑA)
LC-52D65E
LC-52DH65E
LC-52DH65S
PORTUGUÊS
LC-46D65E/LC-52D65E
LC-46DH65E/LC-52DH65E
LC-46DH65S/LC-52DH65S
SHARP ELECTRÓNICA ESPAÑA S.A.
LC-46D65E
LC-46DH65E
LC-46DH65S