MODEL FP-BR-10-ZC

VENT-FREE

WARNING: If information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

−

Do not store or use gasoline or other flammable vapors and liquids in vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow gas supplier’s instructions.

• If you cannot reach your gas supplier, call fire department.

−

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to section “ Producing Adequate Air For Combustion And Ventilation” page 14.

This appliance may be installed in an aftermarket, permanently located, manufactured

(mobile) home, where not prohibited by local codes.

This appliance is only for use with type of gas indicated on rating plate. This appliance is not convertible for use with other gases.

NOTE: An unvented room heater having an input rating of more than 6,000 Btu per hour shall not be

installed in a bathroom.

WARNING:

This appliance is equipped for (natural or propane) gas. Field conversion is not permitted.

INSTALLER: Leave this manual with appliance.

CONSUMER: Retain this manual for future reference.

MANUFACTURED BY NEW BUCK CORPORATION

200 ETHAN ALLEN DRIVE,

SPRUCE PINE, N.C. 28777

www.buckstove.com

Revised March 2012

TABLE OF CONTENTS

Safety Information and Warnings ................................................................................................. 3

Installation ..................................................................................................................................... 6

Fireplace and Framing Dimensions .............................................................................................. 7

Fireplace Clearances ..................................................................................................................... 8

Finishing Your Fireplace .............................................................................................................. 9

Mantel Profiles For Zero Clearance ............................................................................................ 10

Mantel Installation ..................................................................................................................... 11

Mobile Home Installation ........................................................................................................... 13

Gas Connection ........................................................................................................................... 13

Producing Adequate Air for Combustion and Ventilation ........................................................ 14

Air For Combustion And Ventilation Air Iinside Building ........................................................ 16

Air For Combustion And Ventilation Air Outdoors ................................................................... 17

Gas Pressure Check ..................................................................................................................... 18

Placement of Logs ....................................................................................................................... 19

Lighting Instructions ................................................................................................................... 20

Flame Check ............................................................................................................................... 24

Wiring Diagrams ......................................................................................................................... 25

Important Safeguards .................................................................................................................. 27

Trouble Shooting ........................................................................................................................ 28

Service/Replacement Parts .......................................................................................................... 32

Warranty ..................................................................................................................................... 35

SAFETY INFORMATION WARNINGS

IMPORTANT: READ THIS OWNER’S MANUAL CAREFULLY AND COMPLETELY

BEFORE TRYING TO ASSEMBLE, OPERATE, OR SERVICE THIS APPLIANCE.

IMPROPER USE OF THESE LOGS CAN CAUSE SERIOUS INJURY OR DEATH FROM

BURNS, FIRE, EXPLOSION AND CARBON MONOXIDE POISONING.

•

NOTE: When burning any unit or appliance that combusts fuel for heat, such as coal, oil, wood or natural and (L.P.) liquid petroleum gas. We highly recommend the use of smoke and carbon monoxide detectors in your home.

Early signs of carbon monoxide poisoning resemble flu, with headaches, dizziness and/or nausea. If you have these signs, heater may not be working properly. Get fresh air at once! Have burner serviced.

Some people-pregnant women, persons with heart or lung disease, anemia, those under influence of alcohol, those at high altitudes-are more affected by carbon monoxide than others.

Make certain you understand and read all Warnings. Keep this manual for reference. It is your guide to safe and proper operation of this heater and logs.

CAUTION:

Strong drafts, such as a ceiling fan placed directly in front of heater

(pulling from either direction) may create sooting. Sooting will discolor

walls.

1. The installation must conform with local codes, or in absence of local codes, with National Fuel

Gas Code, ANSI Z223.1/NFPA54.

2. This appliance may be installed in an After-Market

*

Manufactured (Mobile) Home, where not prohibited by state or local codes.

*

(After-Market: Completion of sale, not for purpose of resale from manufacturer.)

This appliance is only for use with type of gas indicated on rating plate. This appliance is not convertible for use with other gases.

NOTE: See Page 14, for “Producing Adequate Air For Combustion And Ventilation”.

IMPORTANT:

VENT-FREE HEATERS ADD MOISTURE TO AIR. ALTHOUGH THIS IS

BENEFICIAL, INSTALLING HEATER IN ROOMS WITHOUT ADEQUATE VENTILATION

MAY CAUSE MILDEW TO FORM FROM TOO MUCH MOISTURE.

3. Never install this heater:

- in a recreational vehicle, bathroom.

- where curtains, furniture, clothing, or other flammable objects are less than 42" from

front of heater

-in high traffic areas

- in windy areas

4. Two models are available. One specific model for propane(LP), and one for natural gas. Use correct type gas for your home. Do not convert from one gas type to another.

NOTE: This appliance complies with ANSI Z21.11.2b-2010 Unvented Room Heater.

Page 3

5. If this heater is used with propane gas, do not place propane supply tank (s) inside any structure.

6. What To Do IF You Smell Gas:

Shut off gas supply.

- Do not try to light any appliance.

- Do not touch any electrical switch; do not use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone.

Follow gas supplier’s instructions.

- If you cannot reach your gas supplier, call fire department.

7. When operated for first time, the logs may emit a “paper burning” smell. This smell will gradually diminish and will be totally eliminated after first few hours of operation. Do not use blower at this time.

8. “This heater shall not be installed in unusually tight construction unless provisions are

provided for adequate combustion and ventilation air.” See “Producing Adequate Air For

Combustion And Ventilation”, page 14.

9. Surface of gas logs becomes very hot when operating. Keep children and adults away from hot surface. Gas logs will remain hot for sometime after shutdown. Allow surface to cool before touching.

10. Do not place clothing or other flammable material on or near appliance.

11. If equipped, fresh air damper must be closed.

12. Keep appliance area clean and free from combustible materials, gasoline and other flammable

flammable vapors and liquids. .

13. If burner shuts off, do not relight until you provide fresh outside air. If burner continues to shut off, have unit serviced.

14. Do not use this heater if any part has been under water. Immediately call qualified service

technician to inspect room heater and to replace any part of control system and any gas

control which has been under water.

15. Turn off heater and let cool before servicing.

16. These logs are made of bonded fiber. When removing logs and base, do not damage bonded material. If the material is damaged extensively, loose fiber dust could be emitted into air.

17. Any safety screen or guard removed for servicing an appliance must be replaced prior to

operating heater.

18. This appliance is intended for supplemental heating.

19.

“WARNING:

Any change to this heater or its controls can be dangerous.”

20. Installation and repairs should be performed by a qualified service person. The appliance

should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.

It is imperative that control compartments, burners and circulating air passageways of

appliance be kept clean.

Page 4

21. All heater screens must be kept clean when operating gas logs.

22. .

”WARNING:

Failure to keep the primary air openings of burner clean may result in soot and property damage.”

24. Do not use this heater for burning trash or cooking. Never place matches, paper, garbage or any other material on top of logs or into flames.

24.

Do not install or operate this heater in areas where impurities in air exist (such as tobacco smoke or heavy cooking grease). Particles from impurities may discolor walls.

25.

Due to high temperatures, appliance should be located out of traffic and away from furniture and draperies.

26. Children and adults should be alerted to hazards of high surface temperature and should stay away to avoid burns or clothing ignition.

27. Young children should be carefully supervised when they are in same room with appliance.

28. An unvented room heater having an input rating of more than 6,000 Btu per hour shall not be installed in a bathroom.

29. The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressure in excess of 1/2 psi

(3.5 kPa).

30. The appliance must be isolated from the gas supply piping system by closing its equipment shut-off valve during any pressure testing of gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).

31. “

WARNING:

Do not allow fans to blow directly into fireplace. Avoid any drafts that alter burner flame patterns.”

32. “

WARNING:

Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater.”

Page 5

INSTALLATION

The Model FP-BR10-ZC Vent-Free gas fireplace may be installed in any room in a Residential home or an After-Market* Manufactured Home.

(E

xception: This appliance may not be installed in a bathroom.)

* (After Market: Completion of sale, not for the purpose of resale from manufacturer).

For After-Market Manufactured Home installation, check with state and local codes.

This appliance is only for use with type of gas indicated on rating plate. This appliance is not convertible for use with other gases.

NOTE: See page 14 for “Producing Adequate Air For Combustion And Ventilation”.

CHOOSING THE LOCATION FOR YOUR FIREPLACE:

Figure 1 shows some of many ways your fireplace may be installed. Consider traffic pattern in your room and location of doors and windows. Moving air from ceiling fans, open doors and hot air grills may cause the flames to soot. If a disturbance is found that affects the flames, it must be eliminated by turning off ceiling fan, closing the door or closing or moving th hot air register. A corner location may be best where space is limited.

Your fireplace weighs no more than some of your fine furniture. If fireplace is located near a load bearing wall, additional supports to foundation will not be necessary. HEAVY FACINGS, SUCH AS

BRICK, STONE, ETC., MAY REQUIRE ADDITIONAL FOUNDATION SUPPORT.

NOTE: If this appliance is installed directly on carpeting, tile or other combustible material, other than wood flooring, appliance shall be installed on a metal or wood panel extending full width and depth of appliance.

FIGURE 1

GAS LINES

The gas supply line and electrical supply must be installed before framing in fireplace by a licensed installer.

DRAFTS

Do not locate fireplace in high traffic areas or areas exposed to high drafts and winds.

Locate fireplace away from furniture and draperies.

Page 6

Fireplace and Framing Dimensions (ins.)

11 5/8” 20 3/8”

24”

25 1/8”

26 1/8”

26 1/8”

25 1/8”

GAS

LINE

1 3/4”

13 1/2”

8”

FIGURE 2

WARNING:Installation and repairs should be performed by a qualified service person. The appliance should be inspected before use and at least annually by a professional service person.

More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of appliance be kept clean.

Page 7

FIREPLACE CLEARANCES

The fireplace may be placed directly on a combustible floor, against a combustible wall at marked clear-ances or on a raised wooden platform.

If the fireplace is to be installed on a raised wooden platform, platform must be a continuous level surface. The fireplace must be secured in place so it cannot shift positions. The nailing flanges on the sides of firebox make securing it to framing easy. They were designed to allow installation of 1/2" wallboard or plywood flush with face of fireplace.

Only header (see Figure 2) may rest on stand-offs on top of firebox.

When firebox is installed over carpeting, (vinyl) tile or any combustible material other than wood flooring, it must be installed on a metal or wood panel extending its full width and depth. Alternatively, carpeting, (vinyl) tile, etc. may be removed beneath fireplace before installing.

COMBUSTIBLE MATERIALS MUST NOT BE

INSTALLED OVER OR TOUCH ANY BLACK

PAINTED SURFACE. DO NOT BLOCK HEAT

CIRCULATING AIR OUTLETS. DOING SO MAY

RESULT IN POTENTIAL FIRE HAZARDS.

1. Sidewall Clearances: Clearances from side of fireplace opening to any adjacent combustible wall should not be less than 7".

2. Ceiling Clearances: The ceiling height should not be less than 42" from top of fireplace opening.

17-3/4"

1/2"

INSTALLING THE FIREBOX

Figure 3

TOP

VIEW

This list of specific instructions will help you make certain that every installation operation is performed correctly. Complete installation steps in sequence shown. STATE AND LOCAL

BUILDING CODES SHOULD BE CONSULTED IN ALL

CASES AS TO PARTICULAR REQUIREMENTS

CONCERNING INSTALLATION OF A FACTORY BUILT

FIREPLACES. Select location for fireplace by taking into consideration factors previously outlined in “Choosing the

Location.” See page 5.

Framing the Firebox

The width of framed opening must be 26 1/8". The height of framed opening must be 25 1/8". The entire fireplace can be elevated above floor to achieve a raised hearth effect. This can be done by adding a small platform to achieve desired height.

NOTE: The wiring for lower blower must be installed during framing stage. The nailing flanges on both sides were designed to allow installation of 1/2" wallboard or plywood flush with face of fireplace.

When framing is inside, outside wall will be insulated. If framing or chase is outside, thin insulation should be used in framing on back, sides and top. The bottom should be insulated with a hard insulating board. This will prevent cold from going into chase through fireplace to living space.

Install Firebox

Install firebox into framed opening by placing it directly in front of opening and sliding it into proper position.

Level Firebox

Check level of firebox on top edge of fireplace face. Shim if necessary.

Secure Firebox

Secure fireplace to framing. The nailing flanges on firebox will make securing firebox to frame quick and easy. Use appropriate size nails or screws to secure firebox.

7" *

26-1/8"

* Note: Minimum 1/2" clearance

NOT required at this point

SIDE

VIEW

FRAMING

HEADER

25-1/8"

13-1/2"

FRONT

VIEW

26-1/8"

13-1/2"

25-1/8"

Page 8

FINISHING YOUR FIREPLACE

There is a wide variety of finishing material available Check to see whether man-made brick and stone are for your fireplace from formal wall treatments with made of non combustible materials before using them marble and mantels, to rustic wood paneling, stone or on face of fireplace. Some of these products contain installation such as slate, tile, marble, etc. must be at such as paneling or wallboard may not overlap black least 1/2" thick.

IT IS IMPORTANT THAT THE BLACK FACE OF

face of fireplace. The space between wall covering and fireplace should be sealed with a heat resistant material

FIREPLACE NOT BE COVERED WITH ANY

such as rock wool insulation or mortar.

TYPE OF COMBUSTIBLE MATERIAL.

NOTE: An “L” shaped steel lintel must be installed

Non-combustible facing materials such as marble, brick or ceramic tile may overlap black face of fireplace up to across top of firebox opening where facing materials such as brick or stone is used on face of firebox. It acts opening on either side of fireplace. Seal all joints as a support/firestop. It should be attached to face of between black fireplace face and wall covering with a fireplace with screws and sealed to fireplace with a heat heat-resistant material such as rock wool insulation or -resistant sealer. mortar. Be sure to use high temperature adhesive or mortar when anchoring brick, stone or tile to face of fireplace.

CLEARANCES

3. Mantel Clearances: We have provided 4 different

To ensure a safe installation, the following must be

situations to position your mantel. See Figure 5. carefully observed.

4. Floor Clearances: No clearance is required if

1. Sidewall Clearances: Clearances from right or left appliance is installed per these instructions. side of fireplace opening to any adjacent combustible

5. Front Clearances: From Front of fireplace to any wall should not be less than 7", facing unit. combustible materials should not be any less than

2. Ceiling Clearances: The ceiling height should not

24”. be less than 42" from top of fireplace opening.

NOTE: Adequate clearance around air openings must be maintained. Never cover any openings on appliance with any type material.

FIGURE 4

7" MIN.

CLEARANCE

FROM FIREPLACE

OPENING TO SIDE WALL

42" MIN.

CLEARANCE

TO CEILING

SIDE WALL

LEFT SIDE

24” CLEARANCE TO FRONT

RIGHT SIDE

Page 9

MANTEL PROFILES FOR ZERO CLEARANCE CABINET

MUST BE FOLLOWED

MANTELS WITH 3/4" BASE

CEILING

12"

3-1/2"

COMBUSTIBLE

MATERIAL

COMBUSTIBLE

MATERIAL

10"

3-1/2"

3/4"

42"

3"

3"

3/4"

2-1/2"

STAND OFF

FP-BR10-ZC

2"

LOUVERS

HOOD

STAND OFF

FP-BR10-ZC

2"

LOUVERS

HOOD

Bottom of 3/4" Base or Support must be Flush with top of Unit if mantel is 10" wide or less.

Bottom of 3/4" Base or Support must be at least 2-1/2" from top of Unit if mantel is 10" wide or more.

COMBUSTIBLE

MATERIAL

STAND OFF

FP-BR10-ZC

2"

12"

6"

2-1/2"

SUPPORT

3"

LOUVERS

HOOD

Bottom of 2-1/2" Base or Support must be Flush with top of Unit if mantel is 12" wide or less.

MANTELS WITH 2-1/2" BASE

COMBUSTIBLE

MATERIAL

12"

2-1/2"

2-1/2"

3"

SUPPORT

STAND OFF

FP-BR10-ZC

2"

LOUVERS

HOOD

Bottom of 2-1/2" Base or

Support must be at least

2-1/2" from top of Unit if mantel is 12" wide or more.

Page 10

INSTALLATION OF MODEL FP - BR10- ZC

WITH OPTIONAL WOODEN MANTEL

(1) When choosing right location for your heater and mantel keep following in mind:

NOTE: Due to high temperatures, this heater should be located out of traffic and away

from furniture and draperies.

NOTE: Kit No. (PA KDMH10) Deluxe Wooden Mantel for FP-BR10-ZC.

Kit No. (PA KDM10) Standard Wooden Mantel for FP-BR10-ZC

CAUTION: THE INSTALLATION MUST CONFORM WITH LOCAL CODES OR IN

ABSENCE OF LOCAL CODES, WITH NATIONAL FUEL GAS CODES, ANSI Z223.1/

NFPA 54.

NOTE: See page 18 for “Gas Pressure Check”.

WARNING: YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN

THEY ARE IN SAME ROOM WITH THE APPLIANCE. DO NOT PLACE

CLOTHING OR OTHER FLAMMABLE MATERIAL ON OR NEAR APPLIANCE

(2) Screen(s) can not be removed or altered (Position screen in the closed position before leaving heater unattended).

(3) Follow instructions for assembly of (Optional) Wooden Mantel. See instructions supplied with mantel.

(4) After mantel has been assembled, slide heater from rear into opening of mantel.

NOTE: Place a cloth or blanket over front portions of mantel as not to scar wood.

(5) Center heater in opening of mantel. See Figure 6.

(6) Fasten mantel to hearth by using ½" wood screws.

(7) Insert nine (9) ½" wood screws provided with mantel through slots on nailing flange and secure in place. See Figure 6.

(8) Position mantel and fireplace into desired location.

(9) To light heater, see “Lighting Instructions” pages 19 through 30. Make sure you have right gas valve for Natural or LP gas.

NOTE: Hook gas supply line into heater. Check for leaks using soap and water, not an open

flame.

NOTE: When used as a bedroom fireplace, unit must be attached to the wall. Use angle provided with mantel. Also safety screen must be kept mechanically secured to unit as it is when it leaves manufacturer.

Page 11

1/2" WOOD

SCREWS (9)

TOP MANTEL

REAR

OF

HEATER

MANTEL BASE

FIGURE 6

Page 12

INSTALLATION

AFTER-MARKET MOBILE HOMES

THIS APPLIANCE MAY BE INSTALLED IN AN AFTERMARKET*, PERMANENTLY

LOCATED, MANUFACTURED (MOBILE) HOME, WHERE NOT PROHIBITED BY

LOCAL CODES. *After Market: Completion of sale, not for purpose of resale from manufacturer.

THIS APPLIANCE IS ONLY FOR USE WITH TYPE OF GAS INDICATED ON RATING

PLATE. THIS APPLIANCE IS NOT CONVERTIBLE FOR USE WITH OTHER GASES.

NOTE: For mobile home installation follow “Installation”, pages 6-19.

WARNING:

Installation and repairs should be performed by a qualified service person. The appliance should be inspected before use and at least annually by a professional service person.

More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of appliance be kept clean.

GAS CONNECTION

CHECK GAS TYPE

: Use only type of gas indicated on valve rating plate. If type of gas listed on the plate is not your type of gas supply, DO NOT INSTALL . Contact your dealer for proper model.

Always use an external regulator for all LP heaters to reduce supply tank pressure to a maximum of

13” W.C. This in addition to regulator furnished with heater.

WARNING:

Connection directly to an unregulated LP tank can cause an explosion.

The normal gas connection is 3/8” N.P.T. made at right rear side of appliance.

NOTE: The connecting pipe must be internally tinned copper tubing for use with natural gas. Test for leaks using a solution of soap and water after completing connection. DO NOT USE OPEN

FLAME.

INSTALLATION SUPPLIES

Before installing heater, gather following materials:

- external regulator

(supplied by installer for propane)

- piping (check local codes)

- manual shutoff valve*

- test gauge connection*

- ground joint union

- sediment trap

- tee joint

- pipe wrench

- sealant (resistant to LP gas)

WARNING:

ANY CHANGE TO THIS HEATER OR ITS CONTROLS CAN BE DANGEROUS.

Page 13

PRODUCING ADEQUATE AIR FOR

COMBUSTION AND VENTILATION

This section is for residential or manufactured (mobile) installation

“This heater shall not be installed in unusually tight construction or unconfined space unless provisions are adequate for combustion and ventilation air.”

NOTE: This heater shall not be installed in a room or space unless required volume of indoor combustion air is provided by method in National Fuel Gas Code, ANSIZ223.1/NFPA 54, In-

ternational Fuel Gas Code or applicable codes.

The National Fuel Gas Code, ANSI Z223.1/NFPA 54 defines unusually tight construction or unconfined space as a space whose volume is less than 50 cubic feet per 1,000 BTU per hour

(4.8m

3

per kw) of aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 BTU per hour (4.8m

3

per kw) of aggregate input rating of all appliances installed in that space. Rooms communicating directly with space in which appliances are installed, through openings not furnished with doors, are considered a part of unconfined space.

“WARNING: IF AREA IN WHICH HEATER MAY BE OPERATED DOES NOT

MEET REQUIRED VOLUME FOR INDOOR COMBUSTION AIR, COMBUSTION

AND VENTILATION AIR SHALL BE PROVIDED BY ONE OF METHODS DE-

SCRIBED IN NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54, INTERNATIONAL

FUEL GAS CODE, OR APPLICABLE CODES.”

“WARNING: IF AREA IN WHICH HEATER MAY BE OPERATED IS SMALLER

THAN THAT DEFINED AS AN UNCONFINED SPACE OR IF BUILDING IS OF

UNUSUALLY TIGHT CONSTRUCTION, PROVIDE ADEQUATE AIR FOR

COMBUSTION AND VENTILATION BY ONE OF METHODS DESCRIBED IN

NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54 AIR FOR COMBUSTION AND

VENTILATION, OR APPLICABLE LOCAL CODES.”

Unusually tight construction is defined as construction where: a) Walls and ceilings exposed to outside atmosphere have a continuous water vapor retarder with a rating of 1 perm (6 x 10

-11 kg per pa-sec-m

2

) or less with openings gasketed or sealed; b) Weather stripping has been added on openable windows and doors. c) Caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical and gas lines and at other openings.

NOTE:

SOME AREAS IN THE UNITED STATES HAVE HIGHER REQUIREMENTS

FOR CUBIC FEET PER 1000 BTU/ HOUR INPUT. (EX. CINCINNATI, OHIO CODES

REQUIRE 70 CUBIC FEET). CHECK YOUR LOCAL CODE BEFORE

INSTALLATION.

Page 14

DETERMINING FRESH-AIR FLOW FOR

HEATER LOCATION

DETERMINE IF YOU HAVE UNUSUALLY TIGHT CONSTRUCTION OR UNCONFINED SPACE

Use this worksheet to determine if you have unusually tight construction or unconfined space.

SPACE: Includes room in which you will install heater plus adjoining rooms with doorless passageways or ventilation grills between rooms.

1. Determine volume of the space (length x width x height).

Length x Width x Height =_________cu.ft.(volume of space)

EXAMPLE: 20 ft.(Length) x 16 ft.(Width) x 8 ft.(ceiling Height)=

2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add volume of these rooms to total volume of space.

2. Divide the space volume by 50 cubic feet to determine maximum BTU/Hr space can

support.

_________(volume of space)/50 cu. ft. =maximum BTU/Hr space can support)

EXAMPLE: 2560 cu. ft. (volume of space /50 cu. Ft .= 51.2 or

51200 (maximum BTU/Hr space can support)

3. Add BTU/Hr of all fuel burning appliances in space.

Vent-free heater _______________BTU/Hr

Gas water heater* _______________BTU/Hr

Gas furnace _______________BTU/Hr

Vented gas heater _______________BTU/Hr

Gas fireplace logs _______________BTU/Hr

Other gas appliances* + _______________BTU/Hr

Total = _______________BTU/Hr

Example: Gas water heater 40000 BTU/Hr

Vent-free heater + 18000 BTU/Hr

Total = 58000 BTU/Hr

*Does not include direct-vent gas appliances. Direct-vent draws combustion air from outdoors and vents to outdoors.

4. Compare the maximum BTU/Hr the space can support with actual amount of BTU/Hr used.

____________BTU/Hr (maximum the space can support)

____________BTU/Hr (actual amount of BTU/Hr used)

Example: 51200 BTU/Hr (maximum the space can support)

58000 BTU/Hr (actual amount of BTU/Hr used)

The space in above example is unusually tight construction because actual BTU/Hr used is more than maximum BTU/Hr the space can support. You must provide additional fresh air. Your options are as follows:

Page 15

A. Rework worksheet, adding space of an adjoining room. If extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See

“Ventilation Air From Inside Building”, page 21.

B. Vent room directly to outdoors. See “Ventilation Air From Outdoors”, page 22.

C. Install a lower BTU/Hr heater, if lower BTU/Hr size makes room unconfined.

If actual BTU/Hr used is less than maximum BTU/Hr space can support, space is an unconfined space. You will need no additional fresh air ventilation.

WARNING:

YOU MUST PROVIDE ADDITIONAL VENTILATION AIR IN A UNUSU-

ALLY TIGHT CONSTRUCTION.

AIR FOR COMBUSTION

AND VENTILATION FROM INSIDE BUILDING

This fresh air would come from an adjoining unconfined space. When venting to an adjoining space, you must provide two permanent openings: one within 12" of ceiling and one within 12" of floor on wall connecting two spaces. (See Options 1 and 2, Figure 7.) You can also remove door into adjoining room. (See Option 3, Figure 7.)

WARNING

REWORK WORKSHEET, ADDING SPACE OF ADJOINING UNCONFINED SPACE.

COMBINED SPACES MUST ADEQUATE AMOUNT OF AIR TO SUPPLY ALL

APPLIANCES IN BOTH SPACES.

NOTE: Each opening shall have a minimum free area of 1 square inch per 1000 BTU’s per hour of total input ratings of all gas utilization equipment in confined space, but not less than 100 square inches.

Figure 7 Ventilation Air From Inside Building

Page 16

WARNING

THIS HEATER MUST HAVE ADEQUATE AMOUNT OF AIR FOR PROPER

OPERATION. IF NOT, POOR FUEL COMBUSTION COULD RESULT. READ THE

FOLLOWING INSTRUCTIONS TO ENSURE PROPER AMOUNT OF AIR FOR THIS AND

OTHER FUEL-BURNING APPLIANCES IN YOUR HOME.

AIR FOR COMBUSTION AND

VENTILATION FROM OUTDOORS

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of floor. Connect these items directly to outdoors. These spaces include attics and crawl spaces. Follow National Fuel Gas

Code NFPA 54/ANSI Z223.1, Section 5.3, “Air For Combustion and Ventilation” for required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet air into attic if attic has a thermostatcontrolled power vent. Heated air entering attic will activate power unit.

Ventilated Attic

Outlet Air

Outlet Air

Inlet Air

Inlet Air

To Attic

To Crawl

Space

Ventilation

To Crawl Space

Page 17

GAS PRESSURE CHECK

Check inlet pressure to burner to insure that it is as shown in table below.

NOTE: The pressure check point is located on the right side of valve facing burner.

The appliance and its appliance main gas valve must be disconnected from gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa).

The appliance must be isolated from gas supply piping system by closing its equipment shut-off valve during any pressure testing of gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).

Gas Natural Propane

Heat 10000

Gas Inlet Pressure:

Maximum

Minimum

Manifold Pressure

10.5 ins. W.C.

* 5 ins. W.C.

3.5 ins. W.C.

13 ins. W.C.

*11 ins. W.C.

9 ins. W.C.

NOTE: On initial installation it may be necessary to bleed out air in gas lines. Do this by holding control knob and turning knob to pilot position for about 30 seconds.

To check Regulator pressure, remove pressure tag plug at the left side of Regulator facing heater. The pressure should be checked with heater burning and control set on high. After measuring pressure, replace pressure tap plug, ensuring that there are no leaks.

* For the purpose of minimum input adjustment.

WARNING

This appliance is equipped for (natural or propane) gas.

Field conversion is not permitted.

Page 18

LOG PLACEMENT

Logs are shipped secured in unit.

NOTE: When operated for first time, logs may emit a “paper burning” smell. This smell will gradually diminish and will be totally eliminated after first few hours of operation.

Do not use blower at this time.

Front View of Logs

WARNING

“FAILURE TO POSITION PARTS IN ACCORDANCE WITH THESE DIAGRAMS OR

FAILURE TO USE ONLY PARTS SPECIFICALLY APPROVED WITH HEATER

MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.”

WARNING

“DO NOT ALLOW FANS TO BLOW DIRECTLY INTO THE FIREPLACE. AVOID

ANY DRAFTS THAT ALTER BURNER FLAME PATTERN.”

Page 19

OPERATING INSTRUCTIONS

Before operating this appliance, proceed through following checklist

.

1. Read and understand these instructions before operating this appliance.

2. Check that there no leaks. If you smell gas do not attempt to light this appliance.

LIGHTING INSTRUCTIONS

MODULATING VALVE(MAXITROL)

FOR YOUR SAFETY, READ BEFORE LIGHTING

WARNING

IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EX-

PLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY

OR LOSS OF LIFE.

A. This appliance has a pilot which must be lighted by hand. When lighting pilot,

follow these instructions exactly.

B. BEFORE LIGHTING: Smell all around appliance for gas. Be sure to smell next

to floor because gas is heavier than air and will settle on floor.

WHAT TO DO IF YOU SMELL GAS

* Do not try to light any appliance.

* Do not touch any electrical switch; do not use any phone in your building.

* Immediately call your gas supplier from a neighbor’s phone. Follow gas

supplier’s instructions.

* If you cannot reach your gas supplier, call your local fire department.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If knob

will not push in or turn by hand, don’t try to repair it, call a qualified service technician.

Force or attempted repair may result in fire or explosion.

D. Do not use this appliance if any part has been under water. Immediately call a qualified

service technician to inspect the appliance and to replace any part of control system

and any gas control which has been under water.

Page 20

LIGHTING INSTRUCTIONS

1. STOP! Read safety information on the previous page.

2. Make sure manual shutoff valve is fully closed.

3. Open access panel door, located in lower front center of base for access to control knobs.

4. Turn off all electric power to appliance.

5. Set thermostat (flame control) to lowest setting.

6. Push in and turn control knob clockwise to “OFF” position.

ON

PILOT

IGNITE

FLAME

CONTROL

CONTROL

KNOB

FIGURE 3

7. “Wait (5) five minutes to clear out any gas. Then smell for gas, including near floor. If you smell gas, STOP! Follow step “B” in safety information on previous page. If you don’t smell gas, go to next step.”

8. Find Pilot: follow small metal tub from right hand rear of gas control valve. The pilot is located behind burner tube and in front of rear log. Fully open manual shut-off valve.

9. Turn control knob counterclockwise to “PILOT” position. Press in

control knob for (15) fifteen seconds (see figure 3).

10. With control knob pressed in, turn control knob clockwise to IGNITE and then immediately back to PILOT with button still pressed in. This will light pilot. If needed, keep repeating this step until pilot lights.

11. Keep control knob pressed in for one (1) minute after lighting pilot. After (1) minute,

release control knob. If pilot goes out, repeat steps 1 through 9.

•

If knob does not pop up when released, stop and immediately call your service technician or gas supplier.

•

“If pilot will not stay lit after several tries, turn gas control knob to “OFF” and call your service technician or gas supplier.”

12. Turn control knob counterclockwise to “ON” position.

13. “Set thermostat (flame control) to desired setting. Turn clockwise for “LOW” and counterclockwise for “HIGH”.

Page 21

IGNITER ELECTRODE

THERMO-COUPLE

PILOT

O.D.S

PILOT BURNER

13. Close access panel door.

14. “Turn on all electric power to appliance.”

CAUTION

DO NOT TRY TO ADJUST HEATING LEVELS BY USING

MANUAL SHUTOFF VALVE.

TO TURN OFF GAS TO APPLIANCE

SHUTTING OFF UNIT:

1. Open access panel door, located in lower front center of base for access to control knobs.

2. Set thermostat (flame control) to lowest setting.

2. Turn control knob clockwise to full “OFF” position.

3. “Turn off all electrical power to appliance if service is to be performed.”

4. Close access panel door.

SHUTTING OFF BURNER ONLY (pilot stays lit)

1. Open access panel door, located in lower front center of base for access to control knobs.

2. Turn control knob clockwise to “PILOT” position.

2. Close access panel door.

CAUTION:

Hot while in operation. Do Not Touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

CAUTION:

DO NOT TRY TO ADJUST HEATING LEVELS BY USING MANUAL

SHUTOFF VALVE.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury or loss of life. Refer to owner’s information manual provided with this appliance. Installation and service must be performed by a qualified installer, service agency or the gas supplier.

IMPORTANT:

Always operate appliance at completely “ON” or completely “OFF” positions. Never use the heater at a setting between these positions as this can result in improper combustion and excessive carbon monoxide emissions.

Page 22

THERMOSTAT CONTROL OPERATION

The thermostat control used on this heater differs from standard thermostats. Standard thermostats simply turn burner on and off. The thermostat used on this heater senses room temperature and adjusts amount of gas flow to burner. This will increase or decrease flame height. At times, room may exceed set temperature, which will cause burner to shut off. When room temperature drops below thermostat setting, burner will cycle itself on again. The flame control knob can be set to any level between 2 and 7.

NOTE: The thermostat sensing bulb measures temperature of air near heater cabinet.

This may not always agree with room temperature ( depending on housing construction, installation location , room size, open air temperature, etc.). Frequent use of your heater will allow you to determine your personal comfort levels.

MANUAL LIGHTING PROCEDURE

1. If the pilot cannot be ignited with igniter on the control valve, it can be manually lit with use of a paper match and a lighter rod.

2. Place the match in holder and light. With other hand, depress control knob

counterclockwise to PILOT.

3. Use rod to light match and ignite pilot. The pilot is located behind burner tub and in front of rear log. Fully open manual shut-off valve.

4. Continue to hold control knob for an additional (1) one minute to ensure pilot

is completely on.

•

If knob does not pop up when released, stop and immediately call your service technician or gas supplier.

•

“If the pilot will not stay lit after several tries, turn gas control knob to “OFF” and call your service technician or gas supplier.”

5. Turn control knob counterclockwise to “ON” position.

“Set thermostat (flame control) to desired setting. Turn clockwise for “LOW” and counterclockwise for “HIGH”.

6. Close the access panel door.

7. “Turn on all electric power to appliance.”

Page 23

FLAME CHECK

A periodic check of flames should be made. The pilot flame should always be present when gas logs are in operation.

FLAME: Propane (LP) should produce a flame that is 3"-4" above rear log. This flame should

be yellow.

Natural gas should produce a flame that is 3"-4" above rear log. This flame should

be mostly blue except for the top 1/2" which should be yellow.

FLAME

NATURAL

PROPANE

Page 24

WARNING:

CHILDREN AND ADULTS SHOULD BE ALERTED TO

HAZARDS OF HIGH SURFACE TEMPERATURE AND SHOULD STAY AWAY TO

AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE

CAREFULLY SUPERVISED WHEN THEY ARE IN SAME ROOM WITH

APPLIANCE.

WARNING:

DO NOT PLACE CLOTHING OR OTHER FLAMMABLE

MATERIALS ON OR NEAR APPLIANCE.

WIRING DIAGRAM

JUMPER

THERMOSTAT

MOTOR

JUMPER

JUMPER

GREEN

WHITE

BLACK

BLACK

POWER CORD

Figure 10

RHEOST

NOTE: “If any of original wire as supplied with appliance must be replaced, it must be replaced with a wire of at least a 105 o

C. temperature rating.”

NOTE: Installation and repair should be done by a qualified service person. This heater should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.

It is imperative that control compartments and circulating air passageways of heater be kept clean.

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

Verify proper operation after servicing.

Page 25

WARNING:

ELECTRICAL GROUNDING INSTRUCTION: THIS APPLIANCE

IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR YOUR

PROTECTION AGAINST SHOCK HAZARD AND SHOULD BE PLUGGED

DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE.

NOTE: #PESBRO84 Blower Motor

Rating: 120 volts/60HZ/0.54 Amps. 1 P.H

NOTE: For convenience, allow licensed electrician to install properly grounded

3-plug receptacle near unit.

Page 26

IMPORTANT SAFEGUARDS

Although your gas logs are very realistic in appearance, it is not a real burning fireplace and must not be used for burning rejected material.

•

To avoid irreparable damage to heater or personal injury, matches, paper, garbage or any other material must not be placed or thrown on top of logs or into flames.

•

To avoid personal injury, do not touch hot surfaces when heater is operating.

•

Close supervision is necessary when heater is being operated near children.

WARNING:

THE LOGS ARE MANUFACTURED FROM BONDED CERAMIC

FIBER. THIS IS A COMMONLY USED MATERIAL IN INDUSTRY WORLDWIDE.

IN EVENT THAT A LOG SHOULD BE REMOVED, CARE SHOULD BE TAKEN

NOT TO DAMAGE THE BONDED MATERIAL.INTENTIONAL MISUSE OR

DELIBERATELY FRAGMENTING MATERIAL COULD LEAD TO INHALING

FIBERS AND BE HAZARDOUS TO YOUR HEALTH.

THIS HEATER IS INTENDED FOR USE AS A GAS HEATER FIREPLACE AS

DESCRIBED IN THESE INSTRUCTIONS. IT SHOULD NOT BE USED FOR ANY

OTHER PURPOSE.

CLEANING

CAUTION

:

BEFORE CLEANING OR MOVING THESE LOGS OR OTHER PARTS

OF THE HEATER, BE SURE TO READ ABOVE SECTIONS ON “IMPORTANT

SAFEGUARDS.”

The appliance must be turned “OFF” before cleaning inside firebox (burn area), make sure pilot is “OFF” completely and appliance has cooled.

• All cleaning should be carried out when heater is cold. Limited cleaning is required with normal use. Dusting front of base, top of piezo cover or control knob panel may be required occasionally. Do not use cleaning fluids to clean logs or any other part of heater.

• If flames show unusual shapes or behavior or if burner fails to ignite properly, burner holes may require cleaning. If this occurs, contact your nearest dealer to service heater.

• The heater can be cleaned by removing logs. Lift the logs gently, as not to damage fiber pieces. The logs have been spot glued in place for shipping, use caution when removing.

Lift each log by holding it carefully at each end. Use a vacuum cleaner to remove dust and loose particles from base, logs and around burner and ODS/Pilot. Gloves are recommended to prevent fibers from breaking skin. If skin is broken, clean with soap and water.

WARNING:

Failure to keep the primary air openings of the burner clean may result in soot and property damage.

Page 27

TROUBLESHOOTING

WARNING

TURN OFF BURNER, UNPLUG HEATER AND LET COOL BEFORE

SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD

SERVICE AND REPAIR HEATER.

CAUTION

NEVER USE A WIRE, NEEDLE, OR SIMILAR OBJECT TO CLEAN

ODS/PILOT. THIS CAN DAMAGE ODS/PILOT.

OBSERVED

PROBLEM

1. Igniter button is pressed, no spark at ODS/Pilot

2. Igniter button is pressed

Spark at ODS/Pilot

No Ignition

POSSIBLE

CAUSE

1. I g n i t e r e l e c t r o d e positioned incorrectly.

2. Igniter electrode broken

3. Igniter electrode not connected to igniter cable

4. Igniter cable pinched or wet

5. Piezo igniter nut is loose

6. Broken igniter cable

7. Bad piezo igniter

1. Gas supply turned off or manual shutoff valve is closed

2. Control knob not in

“PILOT” position

3. Control knob not pressed in while in “PILOT” position

4. Air in gas lines when installed

SOLUTION

3. Reconnect igniter cable

4. Free igniter cable if pinched by any metal or tubing. Keep igniter cable dry piezo igniter to heater cabinet. Nut is located inside heater cabinet at top

6. Replace igniter cable

7. Replace piezo igniter

1. Turn on gas supply or open manual shutoff valve

2. Turn control knob to

“PILOT” position

3. Press in control knob while in “PILOT” position

4. Continue to hold down control knob. Repeat igniting operation until air is removed.

Page 28

3. ODS/Pilot lights but flame goes out when control knob is released

4. Burner does not light after

ODS/Pilot is lit

5. Delayed ignition of burner

5. Depleted gas supply

6. ODS/Pilot is clogged

7. Gas regulator setting is not correct

5. Contact local propane gas company

6. Clean ODS/Pilot or replace ODS/Pilot assembly

1. Control knob is not fully pressed in

1. Press control knob completely

2. Control knob not pressed in long enough keep control knob pressed 30 seconds

3. Safety interlock system

3. Wait 1 (one) minute for has been triggered (if safety interlock system equipped) to reset

4. Manual shutoff valve not fully open

5. Thermo-couple connection shutoff valve

5. Hand tighten until snug, loose at control valve then tighten 1/4 turn

6. Pilot flame not touching thermo-couple, which allows thermo-couple to

6. Contact local propane gas company. Clean

ODS/Pilot (See cool causing pilot flame to go out. This problem can be caused by one or both

“Cleaning and

Maintenance”), or replace ODS/Pilot of the following: assembly

A) low gas pressure

B) dirty or partially

clogged ODS/Pilot

7. Control valve damaged

7. Replace valve control

1. Burner orifice is clogged

1. Clean burner (See

2. Inlet gas pressure is too low

“Cleaning and

Maintenance”) or replace burner orifice

2. Contact local propane gas company

1. Manifold pressure is too

1. Contact local propane low

2. Burner orifice is clogged gas company

2. Clean burner (“See

Cleaning and

Maintenance”) or replace burner orifice

Page 29

6. Burner backfiring during combustion

7. Slight smoke or odor during initial operation

8. Heater produces a whistling noise when burner is lit

1. Burner orifice is clogged or damaged

3. Gas regulator defective manufacturing process

1. Turning control knob to

“HI” position when burner is cold (if equipped with this type of valve)

2. Air in gas line

3. Air passageways on heater blocked

4. Dirty or partially clogged burner orifice

1. Clean burner (See “Cleaning and Maintenance “) or replace burner orifice

1. Problem will stop after a few hours of operation

1. Turn control knob to

“LOW” position and allow to warm

2. Operate burner until air is removed from line. Call local propane company to check gas line. installation clearances

4. Clean burner or replace orifice

Page 30

WARNING

IF YOU SMELL GAS:

* SHUT OFF GAS SUPPLY

* DO NOT TRY TO LIGHT APPLIANCE

* DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY

PHONE IN YOUR BUILDING

* IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S

PHONE. FOLLOW GAS SUPPLIER’S INSTRUCTIONS.

* IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL FIRE

DEPARTMENT.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements, glues, new carpet or textiles, etc. create fumes. These fumes may mix with combustion air and create odors.

9. Heater produces a clinking/ticking noise just after burner is lit or shut off

10. Heater produces unwanted odors

11. Heater shuts off in use

(ODS operates)

12. Gas odor even when control knob is in “OFF” position

13. Gas odor during combustion

1. Metal expands while heating or contracts while cooling.

1. Heater burning vapors from paint, hairspray, glues, etc. (See

Important above)

2. Low fuel supply

3. Gas leak (See

WARNING above)

1. Not enough fresh air is available.

2. Low line pressure

3. ODS/Pilot is partially clogged

1. Gas leak (See

WARNING above)

2. Control valve defect

1. Foreign matter between control valve and burner

2. Gas leak (See

WARNING above)

1. This is common with most heaters. If noise is excessive, contact a qualified service person.

1. Ventilate room. Stop using odor causing products while heater is running.

2. Refill supply tank.

3. Locate and control all leaks. See “Checking Gas

Connections”.

1. Open window/door for ventilation

2. Contact local propane co.

1. Locate and correct all leaks (See “Checking Gas

Connections”)

2. Replace control valve

1. Remove foreign matter from gas tubing

2. Locate and correct all leaks “See “Checking Gas

Connections”)

Page 31

SERVICING

Repair and replacement work should only be performed by a qualified service technician.

Always shut off the gas supply and make sure heater is cool before beginning any service operation. Check for gas leaks after servicing.

REPAIR PARTS

A parts list with exploded view follows. Always include correct name, part number and model number of heater when ordering service parts. Please contact your local dealer or Distributor when ordering or if one is not available, you may contact:

New Buck Corporation

P.O. Box 69

Spruce Pine, NC 28777

(828)-765-6144

Page 32

PARTS LIST

Maxitrol Valve

PO

3/8"

Burn Single

1

3/8" 1

14 PO 38634ALMTUB 3/8" x 6 - 3/4" Burner Tube 1

15 PO 54ORFHLD Angled Orifice Holder 1

16 PESBRO84 Blower Motor 1

Page 33

BLOWN UP VIEW OF BURNER ASSEMBLY

*16

Not shown on this page. See page 25, figure 10 for wiring diagram.

Page 34

NEW BUCK CORPORATION

We reserve right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We offer no other warranty, expressed or implied.

LIMITED WARRANTY

MODEL FP-BR10-ZC

New Buck warrants this product to be free from defects in materials and components for two

(2) years from date of first purchase, provided that product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty Bill of Sale or canceled check must be presented.

This warranty is extended only to original retail purchaser and covers cost of parts required to restore heater to proper condition. Warranty parts MUST be obtained through an authorized

Buck Stove dealer and/or New Buck, who will provide original factory replacement parts.

Failure to use original factory replacement parts voids this warranty. The heater must be installed by a qualified installer in accordance with all local codes and instructions furnished with unit.

Warranty does not apply to parts that are not in original condition, normal wear and tear or parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation.

WARRANTY DOES NOT COVER:

- Removal and re-installation cost

- Labor costs for replacements or repairs

- Transportation

- Cost of service call to diagnose trouble

- Painted surfaces

- Damage or defect caused by improper installation, accident, misuse, abuse or alteration

TO FULL EXTENT ALLOWED BY LAW OF THE JURISDICTION THAT GOVERNS

SALE OF PRODUCT, THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL

OTHER EXPRESSED WARRANTIES AND LIMITS DURATION OF ANY AND ALL

WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE TO ONE (1) YEAR FROM DATE OF FIRST

PURCHASE. NEW BUCK LIABILITY IS HEREBY LIMITED TO PURCHASE PRICE OF

PRODUCT AND NEW BUCK SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES

WHATSOEVER INCLUDING INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so above limitation on implied warranties or exclusion on damages may not apply to you.

This warranty gives you specific legal rights. Other rights may vary from state to state.

Page 35

OWNER REGISTRATION

The attached owner registration card must be completed in its entirety and mailed within 30 days from date of installation in order for warranty coverage to begin to:

New Buck Corporation

PLEASE NOTE: Owner Registration Card must contain Authorized Buck Stove Dealer

Number and Certified Installer’s number (if applicable) for warranty coverage to begin.

NAME: _____________________________________________________

ADDRESS: __________________________________________________

CITY: ______________________________________________________

STATE: ______________________ ZIP: ________________________

MODEL #: FP-BR10ZC SERIAL #: ___________________________

DATE OF INSTALLATION: ___________________________________

INSTALLER’S NAME: ________________________________________

PURCHASED FROM: ________________________________________