Sharp LC-37D44E-BK LCD TV

Printed on environmentally friendly paper
Auf ökologischem Papier gedruckt
Imprimé sur papier écologique
Stampato su carta ecologica
Afgedrukt op ecologisch papier
Impreso en papel ecológico
Impresso sobre papel ecológico
PIN
Printed in Poland
Gedruckt in Polen
Imprimé en Pologne
Stampato in Polonia
Gedrukt in Polen
Impreso en Polonia
Impresso na Polónia
TINS-D792WJZZ
1
08P07-PL-NG
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
ESPAÑOL
OPERATION MANUAL / BEDIENUNGSANLEITUNG / MODE D'EMPLOI / MANUALE DI ISTRUZIONI / GEBRUIKSAANWIJZING / MANUAL DE MANEJO /
MANUAL DE OPERAÇÃO
SHARP CORPORATION
PORTUGUÊS
D792WJZZ
Sonninstraße 3, D-20097 Hamburg
LCD COLOUR TELEVISION
LCD-FARBFERNSEHGERÄT
TÉLÉVISEUR COULEUR À ÉCRAN
CRISTAUX LIQUIDES (LCD)
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
TELEVISOR DE CRISTAL LÍQUIDO OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
ENGLISH
LC-37D44E
LC-37D44S
SHARP ELECTRONICS (Europe) GmbH
LC-37D44E
LC-37D44S
LC-37D44E/LC-37D44S
89.6
89,6
903.8
903,8
95.3
95,3
52.0
52,0
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a
safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric
shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
100.0
100,0
200.0
200,0
DANGER:
465.0
465,0
200.0
200,0
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
or )5) and of the same rating as above,
which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains
plug and fit an appropriate type.
366.9
366,9
463.8
463,8
637.0
637,0
585.0
585,0
824.4
824,4
270.0
270,0
ENGLISH
• The models LC-37D44E-BK and LC-37D44S-BK feature a black cabinet.
• The models LC-37D44E-GY and LC-37D44S-GY feature a silver cabinet.
• The illustrations and the OSD (On-Screen Display) in this operation manual are for explanation purposes and may vary slightly
from the actual operations.
• The factory preset PIN is “1234”.
TV only
TV/AV only
TV/DTV/AV only
AV only
PC only
ENGLISH
OPERATION MANUAL
: these icons used throughout this manual indicate
the menu item can be set or adjusted only in the
selected input mode.
Contents
Contents .........................................................................................1
Dear SHARP customer..................................................................2
Important Safety Precautions ......................................................2
Trademarks ....................................................................................2
Supplied accessories ....................................................................3
Quick guide ....................................................................................3
Attaching the stand ...................................................................3
Setting the TV ...........................................................................4
Inserting the batteries................................................................5
Using the remote control unit ....................................................5
Cautions regarding the remote control unit...........................5
Remote control unit...................................................................6
TV (Front view) ..........................................................................7
TV (Rear view) ...........................................................................7
Turning on the power ................................................................8
Standby mode ..........................................................................8
Initial auto installation (Analogue) ...............................................8
Using the analogue programme list ...........................................8
Initial auto installation (DTV) .......................................................8
Using external equipment.............................................................9
Connecting a VCR ....................................................................9
Connecting a game console or camcorder................................9
Connecting a DVD player ..........................................................9
Connecting a decoder ............................................................10
Connecting a PC ....................................................................10
Using AV Link function ............................................................10
Menu operations..........................................................................11
Menu operation buttons ..........................................................11
Operation without a remote control ....................................11
On-Screen Display ..................................................................11
Common operations ...............................................................12
Picture menu ..........................................................................13
AV Mode............................................................................13
Picture adjustments ...........................................................13
Advanced ..........................................................................14
Colour Temp. ................................................................14
Black ............................................................................14
3D-Y/C .........................................................................14
Monochrome ................................................................14
Film Mode.....................................................................14
Audio menu ............................................................................14
AV Mode............................................................................14
Audio adjustments .............................................................14
Surround ...........................................................................15
Auto Vol. ............................................................................15
Clear Voice ........................................................................15
Power Control menu ...............................................................15
No Signal Off .....................................................................15
No Operation Off................................................................15
Power Management ..........................................................15
Setup menu ............................................................................15
Auto Installation .................................................................15
Programme Setup .............................................................16
Auto Search..................................................................16
Manual Adjust ...............................................................16
Fine .........................................................................16
Colour sys. ..............................................................16
Sound sys. (Broadcasting system) ...........................16
Label .......................................................................16
Skip .........................................................................16
Decoder ..................................................................16
Lock ........................................................................17
Sort ..............................................................................17
Erase Programme .........................................................17
Child Lock .........................................................................17
Input Label.........................................................................17
Position .............................................................................18
WSS (Wide Screen Signalling) ............................................18
4:3 Mode ...........................................................................18
Fine Sync. ..........................................................................18
XGA Mode .........................................................................18
Language ..........................................................................18
Supply Voltage ...................................................................18
Option menu ...........................................................................18
Audio Only .........................................................................18
DNR (Digital Noise Reduction) ............................................19
HDMI Setup .......................................................................19
Input Select .......................................................................19
Colour System ...................................................................19
Useful features.............................................................................20
WIDE MODE ...........................................................................20
Still image ...............................................................................21
Teletext function ......................................................................21
DTV menu operations .................................................................22
DTV menu operation buttons ..................................................22
DTV On-Screen Display ..........................................................22
DTV common operations ........................................................22
About using the character set screen .................................23
Language................................................................................23
Programme Setup...................................................................23
Favourite.......................................................................24
Lock .............................................................................24
Move ............................................................................24
Move To........................................................................24
Skip ..............................................................................24
Select ...........................................................................25
Erase ............................................................................25
Label ............................................................................25
View .............................................................................25
Installation...............................................................................25
Auto Installation .................................................................25
Carrier Scan.......................................................................25
Carrier Setup .....................................................................26
System Setup .........................................................................26
OSD Setup ........................................................................26
Child Lock .........................................................................27
Accessories ............................................................................27
Version (Software Version) ..................................................27
Software Upgrade..............................................................27
Common Interface ..................................................................28
Inserting a CA card ...........................................................28
Supplying power to the antenna..............................................28
Useful features (DTV) ..................................................................29
About EPG..............................................................................29
Using the EPG ...................................................................29
Using the EPG Timer ........................................................29
Using the ESG ........................................................................30
Using the digital programme list ..............................................30
Viewing a service banner ........................................................30
Using the multi audio function .................................................31
Displaying subtitles .................................................................31
Using the MHEG5 application (UK only) ..................................31
Appendix ......................................................................................32
Troubleshooting ......................................................................32
PC compatibility chart .............................................................33
RS-232C port specifications ...................................................33
Specifications .........................................................................35
Optional accessory .................................................................35
End of life disposal ..................................................................36
1
LC-37D44E-gb.indd 1
2008/06/16 13:38:04
Dear SHARP customer
Thank you for your purchase of the SHARP LCD colour TV product. To ensure safety and many years of troublefree operation of your product, please read the Important Safety Precautions carefully before using this product.
Important Safety Precautions
• Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners.
• Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, laundry tub,
swimming pool and in a wet basement.
• Do not place vases or any other water-filled containers on this product.
The water may spill onto the product causing fire or electric shock.
• Stand—Do not place the product on an unstable cart, stand, tripod or table. Doing so can cause
the product to fall, resulting in serious personal injuries as well as damage to the product. Use only
a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product.
When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the
mounting hardware recommended by the manufacturer.
• When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops,
excessive force and uneven floor surface can cause the product to fall from the cart.
• Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover or
block these vents and openings since insufficient ventilation can cause overheating and/or shorten the
life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can
block ventilation openings. This product is not designed for built-in installation; do not place the product
in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions
are followed.
• The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or impact
applied. If the LCD panel is broken, be careful not to be injured by broken glass.
• Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
• To prevent fire, never place any type of candle or naked flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• There is power consumption always if main plug is connected.
• Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high
voltage and other dangerous conditions. Request a qualified person to perform servicing.
The LCD panel is a very high technology product, giving you fine picture details.
Due to the very large number of pixels, occasionally a few non-active pixels may appear on the screen as a
fixed point of blue, green or red.
This is within product specifications and does not constitute a fault.
Precautions when transporting the TV
When moving the TV, it should always be carried by two people, using both hands, be careful not to apply
pressure to the display.
Trademarks
• “HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.”
• The “HD ready” Logo is a trademark of EICTA.
• The DVB logo is the registered trademark of the Digital Video Broadcasting - DVB - project.
2
LC-37D44E-gb.indd 2
2008/06/16 13:38:05
Supplied accessories
Remote control unit
(g1)
AC cord (g1)
Cable clamp (g1)
Stand unit (g1)
Page 4
Page 3
Product shape varies
in some countries.
Pages 5 and 6
Page 4
• “AA” size battery (g2) ........ Page 5
• Operation manual (This publication)
Quick guide
Attaching the stand
Before performing work spread cushioning over the base area to lay the TV on, making sure the area is
completely flat. This will prevent it from being damaged.
Before attaching (or detaching) stand, unplug the AC cord from the AC INPUT terminal.
1
Confirm the 10 screws supplied with the TV.
Screws (m10)
2
3
1 Insert the stand into the opening on the
bottom of the TV.
2 Insert and tighten the 4 screws on the rear of
the TV as shown.
Attach the two parts of the stand unit to each
other using the 6 screws as shown.
NOTE
• To detach the stand, perform the above steps in reverse
order.
3
LC-37D44E-gb.indd 3
2008/06/16 13:38:06
Quick guide
Setting the TV
Place the TV close
to the AC outlet, and
keep the power plug
within reach.
Standard DIN45325 plug
(IEC 169-2)
75-ohm coaxial cable
Antenna
Connect the antenna cable from your antenna/cable socket or the (room-/roof) antenna for
antenna input terminal on the back of your TV set to
receive digitally/terrestrially broadcast stations.
An indoor antenna can also be used under good
reception conditions. Passive and active room
antennas are offered commercially. In an active
antenna its power is supplied via the antenna input
terminal.
The supply voltage (5V) must be correspondingly
set under “Supply Voltage”. (See page 18.)
Product shape varies
in some countries.
AC cord
Bundling the cables
Bundle the cables
with the clamp.
Cable clamp
Setting the TV on the wall
• This TV should be mounted on the wall only with the wall mount bracket available from SHARP. (See page 35.)
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
• The centre of the TV screen is 6 mm above “A” engraved onto the metal plate angle used for affixing to a wall.
• Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting
or mounting that results in accident or injury.
• You can ask a qualified service personnel about using an optional bracket to mount the TV to the wall.
4
LC-37D44E-gb.indd 4
2008/06/16 13:38:09
Quick guide
Inserting the batteries
Before using the TV for the first time, insert two “AA” size batteries (supplied). When the batteries become depleted
and the remote control unit fails to operate, replace the batteries with new “AA” size batteries.
1
Hold in the tab on the battery cover and pull the
cover towards the direction of the arrow.
2
Insert two supplied “AA” size batteries.
• Place batteries with their terminals corresponding
to the (e) and (f) indications in the battery
compartment.
3
Insert the smaller tab of the battery cover into
the opening (1), and press down on the cover
until it clicks in place (2).
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any
chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control
unit and sensor may prevent proper operation.
5m
30°
30°
Remote control sensor
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not place in an area with high
humidity.
• Do not install or place the remote control unit under direct sunlight. The heat may cause deformation
of the unit.
• The remote control unit may not work properly if the remote control sensor of the TV is under direct
sunlight or strong lighting. In such case, change the angle of the lighting or TV, or operate the remote
control unit closer to the remote control sensor.
5
LC-37D44E-gb.indd 5
2008/06/16 13:38:11
Quick guide
Remote control unit
1
2
3
B (Standby/On)
Enter standby mode or turn on the
power. (See page 8.)
AV MODE
Select a video setting. (See page 13.)
0–9
Set the channel in TV and DTV mode.
Set the page in Teletext mode.
When one of the 4 Nordic countries
(Sweden, Norway, Finland or
Denmark) is selected in the country
setting of Auto Installation, DTV
channels are 4 digits. When another
country is selected, DTV channels
are 3 digits.
4
5
6
7
8
9
10
11
12
13
A (Flashback)
Press to return to the previous selected
channel or external input mode.
f (WIDE MODE)
Select the wide mode. (See page 20.)
2 (Sound mode)
Select the sound multiplex mode.
(See below.)
EPG
DTV: To display EPG (Electronic
Programme Guide) screen.
ESG
DTV: To display ESG (Electronic Service
Guide) screen. (See page 30.)
m (Teletext)
Select the TELETEXT mode. (See pages
21 and 31.)
DTV: Select DTV data broadcasting and
TELETEXT.
a/b/c/d (Cursor)
Select a desired item on the setting
screen.
END
Exit the menu screen.
k (Reveal hidden Teletext)
(See page 21.)
3 (Freeze/Hold)
(See page 21.)
14
1
2
15
16
17
18
3
19
4
5
20
21
22
23
6
7
8
9
24
25
10
11
26
12
27
13
28
29
14 SURROUND
Switch the surround effects on and off.
(See page 15.)
15 RADIO
DTV: Switch between RADIO and DTV
mode.
16 e (Mute)
Switch the sound on and off.
E Using 2 on the remote control unit
DTV mode:
Press 2 to open the multi audio screen. (See page 31.)
17 DTV
Press to access DTV mode while
watching other input sources, and vice
versa.
(This button will not work if you were
watching DTV immediately before
turning off the TV. In this case first select
any other input source except DTV
using the b button.)
18 i (k/l) (Volume)
i (k) Increase the volume.
i (l) Decrease the volume.
19 P (r/s)
TV/DTV: Select the channel.
External: Switch to TV or DTV input
mode.
Teletext: Move to the next/previous
page.
20 b (INPUT SOURCE)
Select an input source.
(TV, DTV, EXT1, EXT2, EXT3, EXT4,
EXT5, EXT6, EXT7) (See page 9.)
21 SLEEP
Set the sleep timer on (in units of 30
min. up to max. 2 hr. 30 min) and off.
22 p (Display information)
(See pages 21, 29 and 30.)
23 DTV MENU
DTV: Display DTV Menu screen.
24 MENU
Display the MENU screen.
(See page 11.)
25 OK
Execute a command within the menu
screen.
TV/DTV: Display the programme list.
(See pages 8 and 30.)
26 RETURN
Return to the previous menu screen.
27 1 (Subpage)
(See page 21.)
28 [ (Subtitle for Teletext)
TV/External: To turn the subtitles on and
off. (See page 21.)
DTV: Display the subtitle selection
screen. (See page 31.)
29 Colour (Red/Green/Yellow/Blue)
TELETEXT: Select a page. (See page
21.)
DTV: The coloured buttons are used to
select correspondingly to the coloured
items in the menu screen.
Analogue TV mode:
Each time you press 2, the mode switches as illustrated in the following
tables.
NICAM TV broadcasts selection
Signal
Selectable items
A2 TV broadcasts selection
Signal
Selectable items
Stereo
NICAM STEREO, MONO
Stereo
STEREO, MONO
Bilingual
NICAM CH A, NICAM CH B,
NICAM CH AB, MONO
Bilingual
CH A, CH B, CH AB
Monaural
MONO
Monaural
NICAM MONO, MONO
NOTE
• When no signal is input, the sound mode will display “MONO”.
6
LC-37D44E-gb.indd 6
2008/06/16 13:38:13
Quick guide
TV (Front view)
B (Standby/On) indicator
Remote control sensor
TV (Rear view)
a (Power button)
i (l/k) (Volume buttons)
MENU button
P (s/r)
(Programme [channel] buttons)
b (Input Source) button
10
6
7
1
8
13
2
9
3
4
11
5
12
1
2
3
4
5
6
RS-232C terminal
EXT 4 (ANALOGUE RGB/AUDIO)
terminals
EXT 5 (COMPONENT) terminals
EXT 1 (RGB) terminal
EXT 2 (RGB) terminal
Antenna input terminal
(DVB-T 5V=/80 mA)
7
8
9
10
11
12
13
OUTPUT (AUDIO) terminals
EXT 6 (HDMI/AUDIO) terminals
EXT 7 (HDMI) terminal
COMMON INTERFACE slot
EXT 3 terminals
Headphone jack
AC INPUT terminal
WARNING:
Make sure that the volume is turned
down before using or connecting
earphones and headphones.
Listen to audio at moderate levels.
Excessive sound pressure from
earphones and headphones can
cause hearing loss.
NOTE
• Only if you use an active terrestrial antenna, select “On (5V)” under “Supply Voltage”. (See page 18.)
7
LC-37D44E-gb.indd 7
2008/06/17 10:26:25
Quick guide
Turning on the power
Press a on the TV or B on the remote control unit.
Standby mode
Press B on the remote control unit when the TV is
on.
• The TV enters standby mode and the image on the screen
disappears.
• The B indicator on the TV changes from green to red.
• To completely turn off the power to the TV, unplug the AC
cord from the AC outlet. However, do not unplug the AC
cord unless otherwise instructed.
Display status indicator
Off
Power off.
Red
The TV is in standby mode.
Green
The TV is on.
NOTE
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when a is
turned off.
• In DTV input mode, if the power is turned off immediately
after a setting change from the menu screen, the new
setting or channel information may not be memorised.
Initial auto installation (Analogue)
When the TV is powered on for the first time after
purchase, the initial auto installation (Analogue) is
invoked. You can automatically set language, country
and channels in successive operations.
NOTE
• The initial auto installation functions only once. If the initial
auto installation is not completed (ex: When menu screen
disappeared by not operating for a few minutes, when the
power shut down, etc.), try Auto Installation from the Setup
menu. (See page 15.)
• The initial auto installation stops by pressing RETURN.
1
2
Setting the on-screen display language
1 Press a/b/c/d to select the desired language
listed on the screen.
2 Press OK to enter the setting.
Setting the country or area
1 Press a/b/c/d to select your country or area
listed on the screen.
2 Press OK to enter the setting.
• The programme auto search starts at the same time.
After this setting, auto search starts with the following
order:
1
2
3
4
Programme auto search
Auto labelling
Auto sorting
Preset download
Using the analogue programme list
You can also select the desired channel from
programme list instead of using 0 - 9 numeric buttons
or P (r/s).
1
Press OK when no other menu screen is
displayed. (Except when an external input
source is selected.)
2
Press a/b to select the desired channel to
tune in, and then press OK.
3
Press END to exit the Programme List.
Initial auto installation (DTV)
Digital Video Broadcasting is a transmission scheme.
It is much more than a simple replacement for existing
analogue television transmission. DVB provides more
stations, clearer picture quality and other services
displayed on the screen. It also allows a range of new
features and services including subtitles and multiple
audio tracks.
To watch DTV broadcasts, follow the procedures below
to scan all available services in your area.
1
2
Press DTV or b to access the DTV mode.
3
4
Press c/d to select “Installation”.
Press DTV MENU and the DTV Menu screen
displays.
Press a/b to select “Auto Installation”, and
then press OK.
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
• See page 17 for setting PIN.
• A confirmation message displays. Press c/d to
select “Yes”, and then press OK to start the search.
5
The TV starts scanning all available DTV and
radio services in your area.
NOTE
• The language and country settings used in this operation
are the settings you have already set while executing
the Initial auto installation (Analogue). If you want to
reconfigure the country setting, for instance after moving to
another country, conduct “Auto Installation” from the Setup
menu again.
• The services are stored according to the channel number
information embedded in the stream (if available). If
the information is not available, the services are stored
according to the order in which they were received.
If you would like to sort the order, it is possible to arrange it
as explained in page 24.
• To cancel the scan in progress, press END.
• You cannot select any DTV-related menu items unless
“Auto Installation” has been completed.
You do not need to do anything during the auto search.
The setup menu disappears and you can watch the
programme on channel 1.
8
LC-37D44E-gb.indd 8
2008/06/16 13:38:16
Using external equipment
Setting the input source
To view external source images, select the input source using b on the remote control unit or the TV.
NOTE
• The cables marked with * are commercially available items.
Connecting a VCR
Connecting a DVD player
You can use the EXT 1 or 2 terminals when connecting
a VCR and other audiovisual equipment.
If your VCR supports TV-VCR advanced AV Link
systems, you can connect the VCR to the EXT 2
terminal of the TV using the fully-wired SCART cable.
SCART cable*
You can use the EXT 2, 3, 5, 6 (HDMI) or 7 (HDMI)
terminals when connecting to a DVD player and other
audiovisual equipment.
AV OUTPUT
S-video cable*
SCART cable*
or
Composite
video cable*
AUDIO cable*
VCR
Decoder
EXT 3
EXT 1 or 2
DVD player
NOTE
• TV-VCR advanced AV Link systems may not be compatible
with some external sources.
• TV-OUT from EXT 1 is not outputted when EXT 6 (HDMI),
EXT 7 (HDMI) or DTV is selected as the input.
NOTE
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
terminals.
Y
Connecting a game console or
camcorder
Component cable*
PB
PR
A game console, camcorder and some other
audiovisual equipment are conveniently connected
using the EXT 3 terminals.
L-AUDIO-R
COMPONENT
AUDIO cable*
AV OUTPUT
S-video cable*
or
EXT 5
Composite
video cable*
When using an HDMI-DVI
conversion adapter/cable,
input the Audio signal here.
If not, use EXT 7.
AUDIO cable*
DVD player
EXT 3
Game
console
HDMI-DVI conversion adapter/
cable*
Camcorder
EXT 6
NOTE
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
terminals.
DVD player
HDMI-certified cable*
EXT 7
DVD player
NOTE
• When connecting an HDMI-DVI conversion adapter/cable
to the HDMI terminal, the image may not come in clearly.
9
LC-37D44E-gb.indd 9
2008/06/16 13:38:16
Using external equipment
Connecting a decoder
Using AV Link function
You can use the EXT 1 terminal when connecting a
decoder and other audiovisual equipment.
EXT 1
This TV incorporates three typical AV Link functions
for smooth connections between the TV and other
audiovisual equipment.
One Touch Play
While the TV is in standby mode, it automatically turns
on and plays back the image from the audiovisual
source (e.g. VCR, DVD).
SCART cable*
WYSIWYR (What You See Is What You Record)
Decoder
NOTE
• In cases when the decoder needs to receive signal from
the TV, make sure to set “Decoder” to “EXT1” in the
Programme Setup “Manual Adjust” menu. (See page 16.)
• Do not connect the decoder to the EXT 2 terminal.
Connecting a PC
Use the EXT 4 terminals to connect a PC.
EXT 4
PC
RGB cable*
ø 3.5 mm stereo minijack cable*
PC
EXT 4
RGB/DVI conversion cable*
When the remote control unit of the connected VCR
has the WYSIWYR button, you can automatically start
recording by pressing the WYSIWYR button.
Preset Download
Automatically transfers the channel preset information
from the tuner on the TV to the one on the connected
audiovisual equipment (e.g. VCR) via the EXT 2
terminal.
NOTE
• Refer to operation manuals of each external equipment for
the details.
• Only works when the audiovisual equipment is connected
to the EXT 2 terminal on the TV with AV Link via a fully
wired SCART.
• The use of the AV Link function is only possible if the
TV-set has enforced a complete auto-installation with the
connected audiovisual equipment (page 8, Initial auto
installation).
The availability of the AV Link function depends on
the audiovisual equipment used. Depending on the
manufacturer and type of equipment used, it is possible
that the described functions may be completely or partially
unusable.
ø 3.5 mm stereo minijack cable*
NOTE
• The cables marked with * are commercially available items.
• The PC input terminals are DDC1/2B-compatible.
• Refer to page 33 for a list of PC signals compatible with the
TV.
• When connecting to a PC, the correct input signal type is
automatically detected.
10
LC-37D44E-gb.indd 10
2008/06/16 13:38:20
Menu operations
Menu operation buttons
Use the following buttons on the remote control unit to
operate the menu.
On-Screen Display
Example
MENU
[Option ... Colour System]
Option
1
Audio Only
DNR
[Off]
Input Select
[CVBS]
Colour System
[AUTO]
2
3
4
1
Item displayed in white
• This indicates an item can be selected.
2
Item displayed in yellow
• This indicates the item currently selected.
3
Item in brackets
• This indicates the current setting for the item.
4
Item with 4 displayed in grey
• This indicates the item cannot be selected for various
reasons.
NOTE
• Menu options differ in the selected input modes, but the
operating procedures are the same.
• The screens in the operation manual are for explanation
purposes (some are enlarged, others cropped) and may
vary slightly from the actual screens.
MENU:
Press to open or close the menu screen.
a/b/c/d:
Press to select a desired item on the screen
or adjust a selected item.
OK:
Press to go to the next step or complete the
setting.
RETURN:
Press to return to the previous step.
DTV MENU:
Press to open or close the DTV Menu
screen.
END:
Press to exit the menu item.
Operation without a remote control
This function is useful when there is no remote control
within your reach.
1
Press MENU and the “MENU”
screen displays.
2
Press P (s/r) instead of a/b
or i k/l instead of c/d to
select the item.
3
Press b to complete the setting.
NOTE
• The “MENU” screen will disappear if left unattended for
several seconds.
11
LC-37D44E-gb.indd 11
2008/06/16 13:38:21
Menu operations
Common operations
Menu Operation: A
Menu Operation: B
1
Press MENU and the MENU screen displays.
1
Press MENU and the MENU screen displays.
2
Press c/d to select the desired menu.
2
Press c/d to select the desired menu.
3
Press a/b to select the desired menu item,
and then press OK (Example: AV Mode, etc.).
3
Press a/b to select the desired menu item
(Example: Backlight, Contrast, etc.).
• Select “Reset” to reset all adjustment items to the
factory preset values.
4
Press c/d to adjust the item to your desired
position.
MENU
• Select “Reset” to reset all adjustment items to the
factory preset values.
[Picture]
Picture
Audio
AV Mode
MENU
[STANDARD]
Backlight
[+6]
Contrast
[+30]
–8
+8
[Picture ... Backlight]
Picture
Audio
0
+40
AV Mode
Brightness [0]
–30
+30
Backlight
[+6]
–8
[STANDARD]
+8
Colour
[0]
–30
+30
Contrast
[+30]
0
+40
Tint
[0]
–30
+30
Brightness [0]
–30
+30
Sharpness [0]
0
+10
Colour
[0]
–30
+30
Advanced
Tint
[0]
–30
+30
Reset
Sharpness [0]
0
+10
Advanced
4
Press a/b/c/d to select the desired item,
and then press OK.
Reset
Menu Operation: C
1
Press MENU and the MENU screen displays.
STANDARD
2
Press c/d to select the desired menu.
SOFT
3
Press a/b to select the desired menu item,
and then press OK (Example: Advanced, etc.).
4
Press a/b to select the desired menu item,
and then press OK (Example: Colour Temp.,
Black, etc.).
ECO
USER
DYNAMIC
• Select “Reset” to reset all adjustment items to the
factory preset values.
Colour Temp.
Black
3D - Y/C
Monochrome
Film Mode
High
Mid-High
Middle
Mid-Low
Low
5
Press a/b/c/d to select or adjust the desired
item, and then press OK.
12
LC-37D44E-gb.indd 12
2008/06/16 13:38:23
Menu operations
Picture menu
MENU
Picture adjustments
Menu Operation: B (page 12)
Adjust the picture to your preference with the following
picture settings.
[Picture]
Picture
Audio
AV Mode
[STANDARD]
Backlight
[+6]
Contrast
[+30]
Brightness [0]
Colour
Tint
[0]
[0]
Sharpness [0]
–8
+8
0
+40
–30
+30
–30
–30
0
Adjustment items
Selectable
items
c button
d button
Backlight
The screen dims
The screen brightens
Contrast
For less contrast
For more contrast
Brightness
For less brightness
For more brightness
Colour
For less colour
intensity
For more colour
intensity
Tint
Skin tones become
purplish
Skin tones become
greenish
Sharpness
For less sharpness
For more sharpness
+30
+30
+10
Advanced
Reset
AV Mode
Menu Operation: A (page 12)
“AV Mode” gives you several viewing options to choose
from to best match the system environment, which
can vary due to factors like room-brightness, type of
programme watched or the type of image input from
external equipment.
Item
STANDARD: For a highly defined image in a normally
bright room. (Enhanced Picture Contrast: On)
SOFT*: Creates a softer image. (Enhanced Picture
Contrast: On)
ECO*: Reduces power consumption. (Enhanced
Picture Contrast: Off)
USER: Allows the user to customise settings as
desired. You can set the mode for each input source.
(Enhanced Picture Contrast: Off)
DYNAMIC*: For a clear-cut image emphasising high
contrast for sports viewing. (Enhanced Picture
Contrast: On)
NOTE
• You can also select AV Mode options by pressing AV
MODE on the remote control unit.
• You can adjust the factory preset parameters given in
“STANDARD”, “SOFT”, “ECO” and “DYNAMIC”. The
parameters chosen affect each of the input sources.
• The items marked with * are only available for TV/DTV/AV
input mode.
• Enhanced Picture Contrast technology detects the source
video characteristics and smoothly adjusts the screen
brightness accordingly, enabling deeper black levels.
13
LC-37D44E-gb.indd 13
2008/06/16 13:38:24
Menu operations
Advanced
TV/DTV/AV only
Menu Operation: C (page 12)
This TV provides various advanced functions for
optimising the picture quality.
Colour Temp.
Automatically detect a film-based source (originally
encoded at 24/25 frames/second, depending on the
vertical frequency), analyses it then recreates each still
film frame for high-definition picture quality.
Audio menu
Black
High
3D - Y/C
Monochrome
Film Mode
MENU
Mid-High
Film Mode
[Audio]
Audio
Power Control
Middle
AV Mode
[STANDARD]
Mid-Low
Treble
[0]
–15
+15
Bass
[0]
–15
+15
Balance
[0]
L
Low
Colour Temp.
Adjust the colour temperature to give the best white
image.
R
Surround
[Off]
Auto Vol.
[Off]
Clear Voice
[Off]
Reset
Item
High: White with bluish tone
Mid-High: Intermediate tone between High and Middle
Middle: Natural tone
Mid-Low: Intermediate tone between Middle and Low
Low: White with reddish tone
Black
For easier viewing, change the viewing depth by
selecting a level for automatically adjusting the dark
portion of an image.
3D-Y/C
Provide high quality images with minimal dot crawl and
cross colour noise by detecting changes in the image.
Item
Off: No detecting
Standard: Normal adjustment
Fast: Set the optimum image quality for fast-moving
images.
Slow: Set the optimum image quality for slow-moving
images.
AV Mode
Menu Operation: A (page 12)
This option links to AV Mode in the Picture menu. (See
page 13.)
Audio adjustments
Menu Operation: B (page 12)
You can adjust the sound quality to your preference
with the following settings.
Selectable
items
c button
d button
Treble
For weaker treble
For stronger treble
Bass
For weaker bass
For stronger bass
Balance
Decrease audio from
the right speaker
Decrease audio from
the left speaker
NOTE
• 3D-Y/C may not operate depending on the input signal
type or noisy input signal.
• 3D-Y/C has even more effect on composite video signals
(CVBS).
Monochrome
For viewing a video in monochrome.
NOTE
• When Monochrome is set to “On”, the DTV Menu screen
displays in monochrome.
14
LC-37D44E-gb.indd 14
2008/06/16 13:38:24
Menu operations
Surround
Power Management
Menu Operation: A (page 12)
Surround function allows you to enjoy realistic “live”
sound.
NOTE
• You can also choose surround effects by pressing
SURROUND on the remote control unit.
Auto Vol.
TV/DTV/AV only
Menu Operation: A (page 12)
Different sound sources, fairly often do not have the
same volume level, for example the changing from
movie to the advertisements. The Automatic Volume
Control (Auto Vol.) solves this problem and equalises
the volume levels.
Clear Voice
Menu Operation: A (page 12)
This function emphasises speech voice against the
background noise for more intelligibility. It is not
recommended for music sources.
Menu Operation: A (page 12)
When set, the TV will automatically enter the standby
mode.
Item
Off:
• No power management.
• Factory preset value.
Mode1: • If there is no signal input for 8 minutes, the
TV enters the standby mode.
• Even if you start using the PC and the
signal inputs again, the TV stays in standby
mode.
• The TV turns on again by pressing a on
the TV or B on the remote control unit.
(See page 8.)
Mode2: • If there is no signal input for 8 seconds, the
TV enters the standby mode.
• When you start using the PC and the signal
inputs again, the TV turns on.
• The TV turns on again by pressing a on
the TV or B on the remote control unit.
(See page 8.)
Setup menu
Power Control menu
MENU
MENU
[Setup]
Setup
[Power Control]
Power Control
PC only
Setup
Option
Auto Installation
No Signal Off
[Disable]
Programme Setup
No Operation Off
[Disable]
Child Lock
Position
No Signal Off
WSS
TV/AV only
4:3 Mode
Menu Operation: A (page 12)
When set to “Enable” the TV will automatically enter the
standby mode if there is no signal input for 15 minutes.
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
NOTE
• When a TV programme finishes, this function may not
operate.
• This function is not available in DTV mode.
No Operation Off
TV/DTV/AV only
Menu Operation: A (page 12)
When set to “Enable” the TV will automatically enter
the standby mode if no operations are performed for 3
hours.
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
[On]
[Panorama]
Language
[English]
Supply Voltage
[Off (0V)]
Auto Installation
TV only
You can run Auto Installation again, even after setting
up the preset channels.
1
2
3
Press MENU and the MENU screen displays.
Press c/d to select “Setup”.
Press a/b to select “Auto Installation”, and
then press OK.
If you have already set the PIN under “Child
Lock”, enter it here.
• See page 17 for setting PIN.
4
5
Press c/d to select “Yes”, and then press OK.
You can set language and country the same
as in the Initial auto installation (Analogue).
Follow steps 1 and 2 on page 8.
15
LC-37D44E-gb.indd 15
2008/06/16 13:38:25
Menu operations
4
Press a/b to select the desired menu item,
and then press OK.
This section describes how to set up analogue TV
channels manually.
5
Press a/b/c/d to select or adjust.
1
2
3
NOTE
• When you exit Programme Setup “Manual Adjust”
menu, preset download automatically runs if you change
information on that menu.
Programme Setup
TV only
Press MENU and the MENU screen displays.
Press c/d to select “Setup”.
Press a/b to select “Programme Setup”, and
then press OK.
If you have already set the PIN under “Child
Lock”, enter it here.
• See page 17 for setting PIN.
4
Press a/b to select “Auto Search”, “Manual
Adjust”, “Sort” or “Erase Programme”, and then
press OK.
Fine
You can adjust the frequency to your desired position.
NOTE
• Adjust while checking the background picture as a
reference.
• Instead of pressing c/d to adjust the frequency in step
5 above, you can set by directly entering the frequency
number of the channel with 0 – 9.
Auto Search
EXAMPLE
• 179.25 MHz: Press 1 s 7 s 9 s 2 s 5.
• 49.25 MHz: Press 4 s 9 s 2 s 5 s OK.
Manual Adjust
Sort
Erase Programme
No
Colour sys.
Yes
Select the optimum colour systems to receive. (AUTO,
PAL, SECAM)
Sound sys. (Broadcasting system)
Auto Search
You can automatically search for and download TV
channels by performing the procedure below. This is
the same function as from programme auto search to
preset download in Auto Installation.
1
2
Repeat steps 1 to 4 in Programme Setup.
Press c/d to select “Yes”, and then press OK.
1
2
3
4
Programme auto search
Auto labelling
Auto sorting
Preset download
You can set some channel items manually.
[Setup ... Programme Setup]
Fine
1
2
3
1
2
Repeat steps 1 to 4 in Manual Adjust.
Press a/b/c/d to select each character of
the new name for the channel, and then press
OK.
Repeat step 2 above until the name is fully spelt
out.
• The name can be 5 characters or less.
• If a channel name is less than 5 characters, select
“END”, then press OK.
[179.25]
Colour sys.
[AUTO]
Sound sys.
[B/G]
Label
Label
When a TV channel sends its Network Name, the Auto
Installation detects the information and assigns a name
to it. However, you can change individual channel
names.
3
Manual Adjust
MENU
Select the optimum sound systems (Broadcasting
systems) to receive. (B/G, D/K, I, L, L’)
Skip
179.25
MHz
[SAT.1]
Skip
[Off]
Decoder
[Off]
Lock
[Off]
Repeat steps 1 to 4 in Programme Setup.
Press c/d to select “Yes”, and then press OK.
Press a/b/c/d to select the channel you
want to edit, and then press OK.
Channels with “Skip” set to “On” are passed over when
using P (r/s) even if selected while watching the
image from the TV.
Decoder
When connecting a decoder to the unit, you need to
select EXT1.
NOTE
• “Off” is factory preset value.
• The selected channel information displays.
16
LC-37D44E-gb.indd 16
2008/06/16 13:38:26
Menu operations
4
5
Lock
You can block the viewing of any channel.
NOTE
• See “Child Lock” for setting PIN.
• When Lock is set to “On” for a channel, “Child lock has
been activated.” displays, and the image and sound of the
channel are blocked.
• When pressing OK while “Child lock has been activated.”
displays, PIN input menu will display. Inputting the correct
PIN lifts the child lock temporarily until the power is turned
off.
Enter the 4-digit number as a PIN using 0 – 9.
Enter the same 4-digit number as in step 4 to
confirm.
• “The system PIN has been changed successfully”
displays.
NOTE
• To view a locked channel, you must enter a PIN. (See this
page and page 27 for locking channels from viewing in
analogue TV and DTV mode.) When you select a locked
channel, a PIN prompt message pops up. Press OK to
display the PIN input window.
Resetting the PIN
Sort
Channel positions can be sorted freely.
Allow you to reset your PIN to the factory preset
“1234”.
1
2
3
1
2
3
Repeat steps 1 to 4 in Programme Setup.
Press c/d to select “Yes”, and then press OK.
Press a/b/c/d to select the channel you
want to move, and then press OK.
4
Press a/b/c/d to move it to the desired
position, and then press OK.
5
Repeat steps 3 and 4 until all desired channels
are sorted.
Erase Programme
An individual programme can be erased.
1
2
3
Repeat steps 1 to 4 in Programme Setup.
Press c/d to select “Yes”, and then press
OK.
Press a/b/c/d to select the channel you
want to erase, and then press OK.
• A message screen pops up.
4
Press c/d to select “Yes”, and then press
OK to erase the selected programme. All the
subsequent programmes move up.
5
Repeat steps 3 and 4 until all desired channels
are erased.
Child Lock
TV only
Allow you to use a PIN to protect certain settings from
being accidentally changed.
Changing the PIN
1
2
3
Press MENU and the MENU screen displays.
4
Repeat steps 1 to 3 in Changing the PIN.
Enter the PIN.
Press a/b to select “Reset”, and then press
OK.
Press c/d to select “Yes”, and then press OK.
NOTE
• As a precautionary measure, make a note of your PIN
on the back of this operation manual, cut it out and
keep it in a safe place that children cannot reach.
• See page 32 for resetting the current PIN to the
factory preset “1234” if you lose or forget your PIN.
Input Label
You can assign each input source a label you like.
1
2
3
4
Press b to select the desired input source.
Press MENU and the MENU screen displays.
Press c/d to select “Setup”.
Press a/b to select “Input Label”, and then
press OK.
5
Press a/b/c/d to select each character of
the new name for the input source, and then
press OK.
6
Repeat step 5 above until the name is fully spelt
out, and then press OK.
• The name can be 6 characters or less.
• If a label name is less than 6 characters, select
“END”, then press OK.
NOTE
• You cannot change the label if the input source is TV or
DTV.
Press c/d to select “Setup”.
Press a/b to select “Child Lock”, and then
press OK.
Change PIN
Reset
New PIN
– – – –
Reconfirm
– – – –
17
LC-37D44E-gb.indd 17
2008/06/16 13:38:26
Menu operations
Position
TV/DTV/AV only
Menu Operation: C (page 12)
For adjusting a picture’s horizontal and vertical position.
Item
H-Pos.: Centres the image by moving it to the left or
right.
V-Pos.: Centres the image by moving it up or down.
NOTE
• Adjustments are stored separately according to input
source.
• Depending on the input signal type a position setting may
not be available.
WSS (Wide Screen Signalling)
TV/DTV/AV only
Menu Operation: A (page 12)
WSS allows a television to switch automatically among
the different screen formats.
NOTE
• Use WIDE MODE if an image does not switch to the
correct screen format. When the broadcast signal contains
no WSS information, the function will not work even if
enabled. (See page 20.)
4:3 Mode
TV/DTV/AV only
Menu Operation: A (page 12)
The WSS signal has 4:3 auto-switching that allows you
to select between Normal and Panorama.
Item
Normal: Normal range keeping 4:3 or 16:9 aspect ratio
Panorama: Wide image without side bars
WSS signal 4:3 screen
4:3 mode “Normal”
4:3 mode “Panorama”
XGA Mode
PC only
Menu Operation: C (page 12)
You can select one of the 3 input signals listed below
to adjust the picture resolution when the PC input is an
XGA signal.
1024 g 768
1280 g 768
1360 g 768
NOTE
• Depending on the graphics card, resolutions of 1360 g
768 may not display correctly.
Language
Menu Operation: A (page 12)
You can select a language from the Setup menu.
Select desired language listed on the screen.
Supply Voltage
TV/DTV/AV only
Menu Operation: A (page 12)
Switch on or off the power to the antenna connected
to the antenna input terminal. (See page 4.)
Option menu
MENU
[Option]
Option
Audio Only
DNR
[Off]
Input Select
[CVBS]
Colour System
[AUTO]
NOTE
• “HDMI Setup” is displayed only when “EXT6” or “EXT7” is
selected from the INPUT SOURCE menu.
Audio Only
Fine Sync.
PC only
Menu Operation: C (page 12)
Ordinarily, the TV automatically adjusts image positions
coming from PC (Auto Sync. function). In some cases,
however, manual adjustment is needed to optimise the
image.
Menu Operation: A (page 12)
When listening to music from a music programme, you
can set the TV off and enjoy audio only.
Item
Off: Both screen images and audio are output.
On: Audio is output without screen image.
Item
H-Pos.: Centres the image by moving it to the left or
right.
V-Pos.: Centres the image by moving it up or down.
Clock: Adjusts when the image flickers with vertical
stripes.
Phase: Adjusts when characters have low contrast or
when the image flickers.
NOTE
• If you need to adjust the image position, adjust the position
using your PC.
18
LC-37D44E-gb.indd 18
2008/06/16 13:38:27
Menu operations
DNR (Digital Noise Reduction)
TV/DTV/AV only
Menu Operation: A (page 12)
Produce a clearer image. (Off, High, Low)
HDMI Setup
Menu Operation: A (page 12)
For setting the signal type of external equipment.
AV only
HDMI (High-Definition Multimedia Interface) terminal
selection.
1
To watch an HDMI equipment image, select
“EXT6” or “EXT7” (the terminal which you are
using) from “INPUT SOURCE” menu using b
on the remote control unit or TV.
2
3
4
Press MENU and the MENU screen displays.
Press c/d to select “Option”.
Press a/b to select “HDMI Setup”, and then
press OK.
• “HDMI Setup” is displayed only when “EXT6” or
“EXT7” is selected from the INPUT SOURCE menu.
MENU
[Off]
HDMI Setup
5
Press a/b to select the desired item, and then
press OK.
6
Press a/b/c/d to select the desired setting,
and then press OK.
Selectable items
Signal type
Y/C, CVBS, RGB
EXT 2
Y/C, CVBS, RGB
NOTE
• If no (colour) image displays, try to change the other
signal type.
• Check the operation manual of the external equipment for
the signal type.
• TV, EXT3, EXT4, EXT5, EXT6 and EXT7 are not displayed in
Input Select.
• If both CVBS and RGB signals are input to EXT 1 or EXT
2 using a SCART cable, the TV may output an RGB signal
even though you have designated CVBS for the respective
terminal. This happens due to the setting of your external
equipment.
TV/AV only
Menu Operation: A (page 12)
You can change the colour system to one that is
compatible with the image on the screen. (AUTO, PAL,
SECAM, NTSC3.58, NTSC4.43, PAL-60)
Audio Only
HDMI Setup
items
Input source
EXT 1
Colour System
[Option ... HDMI Setup]
Option
DNR
Input Select
Description
Signal Type*
RGB/YCbCr 4:4:4/
YCbCr 4:2:2
Select the video signal
type from the HDMI
terminal.
Colour Matrix*
ITU601/ITU709
Select the internal
colour space
conversion method
when an RGB signal
is input.
Dynamic
Range*
Normal/Enhanced
Select the signal
amplitude range.
Usually, select
“Normal”.
Auto View
Disable/Enable
Set whether or not
to use WIDE MODE
based on signal
recognition, including
an HDMI signal.
Audio Select**
Digital/Analogue
Select “Digital” for
audio signal via the
HDMI terminal. Select
“Analogue” for audio
signal via the AUDIO
jack.
NOTE
• Factory preset value is “AUTO”.
• If “AUTO” is selected, colour system for each channel is
automatically set. If an image does not display clearly,
select another colour system (e.g. PAL, SECAM).
• “NTSC3.58”, “NTSC4.43” and “PAL-60” cannot be
selected in TV tuner mode.
NOTE
• Refer to your external equipment operation manual for the
signal type.
• Items marked * may be greyed out (with 4) depending on
the type of signal input from the external equipment.
• Item marked ** is only available when EXT6 is selected.
19
LC-37D44E-gb.indd 19
2008/06/16 13:38:28
Useful features
WIDE MODE
TV/AV only
You can select the picture size. Selectable picture size
varies with the type of signal received.
Item (for SD (Standard-Definition) signal)
Normal: For 4:3 “standard” pictures. A side bar
appears on each side.
Zoom 14:9: For 14:9 letterbox pictures. A thin side bar
appears on each side, and you may see bars on the
top and bottom with some programmes.
Panorama: In this mode the picture is progressively
stretched toward each side of the screen.
Full: For 16:9 squeeze pictures.
Cinema 16:9: For 16:9 letterbox pictures. Bars
may appear on the top and bottom with some
programmes.
Cinema 14:9: For 14:9 letterbox pictures. Bars
may appear on the top and bottom with some
programmes.
Item (for HD (High-Definition) signal)
Full: Display with the Overscan image. Crop all sides of
screen.
Manual Selection
1
Press f.
• The WIDE MODE menu displays.
• The menu lists the wide mode options selectable for
the type of video signal currently received.
2
WIDE MODE
PC only
You can select the picture size.
1
Press f.
• The WIDE MODE menu displays.
2
Press f or a/b to select a desired item on
the menu.
NOTE
• Connect the PC before making adjustments. (See page
10.)
• Selectable picture size may vary with input signal type.
EXAMPLE
Normal
Full
Item
Normal: Keeps the original aspect ratio in a full screen
display.
Full: An image fully fills the screen.
Press f or a/b while the WIDE MODE menu
displays on the screen.
• As you toggle down the options, each is immediately
reflected on the screen. No need to press OK.
Auto Selection
If you set WSS and 4:3 Mode in the Setup menu on
page 18, the optimum WIDE MODE is automatically
chosen for every broadcast, VCR or DVD containing
the WSS information.
WSS menu
To enable Auto Selection, set WSS in the Setup menu
to “On”. (See page 18.)
4:3 Mode menu
To set the type of the wide screen, select “Normal” or
“Panorama” in the 4:3 Mode menu. (See page 18.)
4:3 Mode set to “Normal”
4:3 Mode set to “Panorama”
NOTE
• If the signal contains no WSS information, Auto Selection
will not function even when the WSS option is enabled.
20
LC-37D44E-gb.indd 20
2008/06/16 13:38:28
Useful features
Time display
Still image
You can freeze a motion picture on the screen.
1
2
Press 3.
You can display the time information included in the
DTV and Teletext broadcasts.
NOTE
• Skip step 1 if receiving DTV broadcasts.
Press 3 again to exit still image.
NOTE
• When this function is not available, “No still image display
available.” will display.
• The still image automatically goes out after 30 minutes.
Teletext function
1
Select a TV channel providing Teletext
information. (The time information is
automatically captured.)
2
Press p. The channel display will appear on
the TV.
3
Press p again within the several seconds that
the channel display is on the screen.
Time information will display below the channel
display for several seconds.
4
Even when you change the TV channel, you can
display the time information with steps 2 and 3
above.
What is Teletext?
Teletext broadcasts pages of information and
entertainment to specially equipped television sets.
Your TV receives Teletext signals broadcast by a TV
network, and decodes them into graphical format for
viewing. News, weather and sports information, stock
exchange prices and programme previews are among
the many services available.
1
Select a TV channel or external input source
providing the Teletext programme.
NOTE
• The time display cannot be stored once the power is
turned off. When you turn on the power, perform steps 1 to
4 again.
• If acquired successfully, the time information will appear in
the upper-right corner of the screen by pressing MENU.
2
3
Press m to display the Teletext.
Button functions
Turning on and off Teletext
Press m again to display the Teletext on the
right screen and normal image on the left
screen.
Buttons
P (r/s)
Increase or decrease the page number.
• Each time you press m, the screen switches as
shown below.
Colour (Red/
Green/Yellow/
Blue)
Select a group or block of pages displayed in
the coloured brackets at the bottom of the
screen by pressing the corresponding Colour
(Red/Green/Yellow/Blue) on the remote
control unit.
0–9
Directly select any page from 100 to 899 by
using 0 – 9.
DATA*
TELETEXT
Description
Reveal or hide hidden information such as an
k (Reveal
hidden Teletext) answer to a quiz.
TELETEXT
* May appear in DTV input mode.
• If you select a programme with no Teletext signal,
“No Teletext available.” displays.
• The same message displays during other modes if no
Teletext signal is available.
NOTE
• Teletext will not work if the selected signal type is RGB.
(See page 19.)
3 (Freeze/
Hold)
Stop updating Teletext pages automatically or
release the hold mode.
[ (Subtitle for
Teletext)
Display the subtitle or exit the subtitle screen.
• Subtitle will not be displayed when the
service does not contain the subtitle
information.
1 (Subpage)
Reveal or hide subpages.
• Red button: Move to the previous subpage.
• Green button: Move to the following
subpage.
• These two buttons are shown on the screen
by the signs l and k.
21
LC-37D44E-gb.indd 21
2008/06/16 13:38:30
DTV menu operations
DTV menu operation buttons
Use the following buttons on the remote control unit to
operate the DTV Menu.
DTV On-Screen Display
Example
DTV MENU / Language
1
2
3
4
5
6
7
Select
1
DTV MENU
OK
END
Language
• To customise the language preference for audio and
MHEG5 application.
2
[:
Press to display the subtitle selection
screen.
m:
Press to display TELETEXT or start the
MHEG5 presentation, if available.
-
:
Aside from direct channel entry, each of the
numeric buttons have a unique
function assigned in the Programme Setup
screen.
DTV:
Press to access DTV mode.
EPG:
Press to open the EPG screen.
ESG:
Press to open the ESG screen.
RADIO:
Press to switch between TV and RADIO
mode.
• Due to the large variation in transmitted
volume levels in RADIO mode, some
stations will produce distortion if the
volume level is set too high.
2:
Press to open the multi audio screen.
DTV MENU:
Press to open or close the DTV Menu
screen.
p:
Press to open the service banner or view
detailed information from the EPG/ESG
screen.
a/b/c/d:
Press to select a desired item on the screen
or adjust a selected item.
OK:
Press to go to the next step or complete the
setting.
Press to open the Programme List when no
other menu screen is active. (Except when
an external input source is selected.)
END:
Press to exit the current menu screen
without saving the changes.
Colour:
Each of the coloured buttons have a unique
function assigned in the menu screen.
RETURN:
Press to return to the previous step.
Programme Setup
• To configure various settings for each service. These
include: Fav(ourite), Lock, Move, Move To, Skip,
Select, Erase, Label, and View functions.
3
Installation
• To scan all services available in your area, or to label/
erase/re-scan the selected carrier.
4
System Setup
• To configure On-Screen Display and Child Lock
settings.
5
Accessories
• To display the current version of the software or to
allow the software upgrade to take place.
6
Common Interface
• To display the current Common Interface details.
7
Navigation buttons
• To navigate within the DTV Menu screen.
DTV common operations
DTV common menu operation
1
Press DTV or b to access the DTV mode.
2
Press DTV MENU and the DTV Menu screen
displays.
3
Press c/d to select the desired menu, and
then press OK if necessary.
• From this point, menu operations differ depending on
the item you are going to adjust. See the respective
section of the menu operation.
• You cannot select any DTV-related menu items
unless “Auto Installation” has been completed.
• Press RADIO to switch between DTV and Radio
mode.
• To exit the current screen without saving the change,
press END.
22
LC-37D44E-gb.indd 22
2008/06/16 13:38:32
DTV menu operations
About using the character set screen
In some cases you may be prompted to enter
characters. See below for details.
Sample Alpha Numerical Character Set screen
1
2
Alpha Numerical Character Set
1
2
FAV
!
~
#
$
%
&
‘
(
)
*
+
,
-
.
/
0
1
2
3
4
5
6
7
8
9
;
:
<
_
>
?
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
`
=
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
4
3
3
Select
0...9
5
1
Input area
2
Space
3
4
Character select area
YELLOW (Select) button
OK
Language
Select language settings for audio (if a programme is
broadcast in more than one language) and MHEG5
service.
END
6
To add or overwrite with a space.
Press OK while the cursor is on “Language”.
Press a/b to select “1st Pref. Audio”, “2nd
Pref. Audio”, “3rd Pref. Audio” or “MHEG”.
Select a desired language for each item.
NOTE
• See page 18 to change the language displayed on-screen.
• See page 31 to change the subtitle language.
• See page 31 for details on the MHEG5 service.
Basque
Catalan
Croatian
Czech
Danish
Dutch
English*
Finnish
French
Gaelic*
Gallegan
German
Available language list
Greek
Italian
Norwegian
Polish
Portuguese
Russian
Serbian
Slovak
Spanish
Swedish
Turkish
Welsh*
* Languages available for MHEG5 service
Press to move between the input area and character
select area.
5
a/b/c/d button
Press to move the cursor.
6
OK button
While in the input area:
Confirms the new name.
Once OK is pressed to confirm, a confirmation
message displays.
Press c/d to select “Yes”, and then press OK.
While in the character select area:
Confirms the input of a character.
Programme Setup
Configure various settings for each service. Press the
numeric buttons to access each
preassigned
of the functions explained below.
Press OK while the cursor is on “Programme
Setup”.
Sample Programme Setup screen
Programme Setup
Sample operation using Alpha Numerical
Character Set
S.No Services
1
Call up the character set screen while in the
“Label” or “Carrier Setup” screen. (See pages
25 and 26.)
2
Press YELLOW (Select) to move the cursor to
the character select area.
3
Press a/b/c/d to select the desired
character, and then press OK. Repeat until the
new name is fully entered.
• Use space to add a space or overwrite.
4
To register the new name, press YELLOW
(Select) to move the cursor back to the input
area.
5
Press OK.
Fav
Lock
BBC
002
BBC News
003
BBC 1
004
BBC 2
1.
3.
5.
7.
9.
Select
Skip Erase Move
1
001
0...9
DTV MENU
OK
Fav
Move
Skip
Erase
View
END
2.
4.
6.
8.
Lock
Move To
Select
Label
RADIO
TV/Radio
NOTE
• The picture window shows a blank image if Radio services
are listed.
• A confirmation message displays.
6
Press c/d to select “Yes”, and then press OK.
23
LC-37D44E-gb.indd 23
2008/06/16 13:38:36
DTV menu operations
EXAMPLE:
Favourite
Assign services to 4 different favourite groups.
1
2
3
Press a/b to select the desired service.
Press
on the remote control. A selection box
displays.
Press a/b to register the selected service to
any of the 4 favourite groups (None, Fav 1 ...
Fav 4) and then press OK. An icon displays
indicating the favourite status.
• Do not press END to exit the screen here if you wish
to register the change.
4
5
Moving “002 ZDF” ahead of “001 ARD”.
Default order: Press a/b to select the desired service
in 001rs002rs003rs004.
Sorted order: Press a/b to select the desired service
in 002rs001rs003rs004.
Press OK.
Now you can easily select your favourite service
from the Programme List. (See page 30.)
NOTE
• You cannot register the same service to two different
favourite groups.
1
2
Press a/b to select the desired service.
3
Press OK.
NOTE
• See page 17 for setting the PIN.
1
2
3
1
2
Press a/b to select the desired service.
on the remote control. An icon
Press
displays indicating the service to be moved.
• Pressing
3
003
SAT. 1
004
RTL
s
002
ZDF
001
ARD
003
SAT. 1
004
RTL
Press a/b to select the desired service.
on the remote control.
Press
Enter the number you want to change to using
numeric buttons, and then press OK.
The positions of the selected services are
switched.
• Do not press END to exit the screen here if you wish
to register the change.
• You cannot enter a service number that is not listed.
4
Press OK again, the message “Successfully
updated” displays. The change is now
registered.
001
ZDF
001
RTL
002
ARD
002
ARD
003
SAT. 1
003
SAT. 1
004
RTL
004
ZDF
s
Skip
Services that are set to skip will not be picked up when
pressing P (r/s).
1
2
Press a/b to select the desired service.
on the remote control. An icon
Press
displays indicating the service to be skipped.
• Pressing
will turn the skip icon on and off.
• Do not press END to exit the screen here if you wish
to register the change.
Move
Sort the order of the selected service by moving the
service position.
ZDF
Use this function to change the position of two
selected services.
on the remote control.
Press
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
An icon displays indicating the service is
locked.
• Pressing
will turn the lock icon on and off. (PIN
entry is required when lifting the lock icon.)
• Do not press END to exit the screen here if you wish
to register the change.
ARD
002
Move To
Lock
When the service is locked, you must enter your PIN
whenever you tune to the service.
001
3
Press OK.
NOTE
• To view services that are set to be skipped, use
numeric buttons or select from the Programme List.
will turn the move icon on and off.
Move the selected service to the desired
position using a/b, and then press OK.
• Do not press END to exit the screen here if you wish
to register the change.
4
Press OK to register the change.
24
LC-37D44E-gb.indd 24
2008/06/16 13:38:37
DTV menu operations
Installation
Select
Use this function to jump to the specific service in
one step. This is useful when there are many services
displayed on screen to scroll through.
1
2
on the remote control. Now you can
Press
change the service number on the left side of
the screen.
numeric
Enter the number using
buttons, and then press OK. The highlight
moves to the selected service.
Erase
Erase the selected service(s) from the memory.
1
2
Press a/b to select the desired service.
Press
on the remote control. An icon
displays indicating the service to be erased.
• Pressing
will turn the erase icon on and off.
• Do not press END to exit the screen here if you wish
to register the change.
3
Press OK.
• A confirmation message displays.
4
This section describes how to reconfigure the DTV
settings after conducting Initial auto installation
(DTV) on page 8.
Auto Installation
The TV automatically detects and stores all available
services in your area. See Initial auto installation
(DTV) on page 8 for details.
NOTE
• If the TV detects a new carrier/service that has become
available after performing “Auto Installation”, the message
“Do you want to save?” displays.
Press c/d to select “Yes” or “No”, and then press OK.
Carrier Scan
Manually add a new carrier by entering the desired
carrier number or frequency band.
1
2
Press c/d to select “Yes”, and then press OK.
Label
Press c/d to select “Installation”.
Press a/b to select “Carrier Scan”, and then
press OK.
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
Carrier Scan
Change individual service names.
1
2
3
Press a/b to select the desired service.
Channel
on the remote control. A character set
Press
screen displays.
Frequency (kHz)
Enter new name for the service. See page 23 for
operations using the character set screen.
Select
3
View
Press a/b to select the desired service.
Press
on the remote control.
• The image shown in the picture window changes.
3
Press END to exit the Programme Setup screen
to view the image in full screen.
0...9
DTV MENU
OK
END
Press a/b to select “Channel”, then c/d to
enter the carrier number, and then press OK.
• The frequency of the selected carrier in the below cell
changes correspondingly.
Tune to the service shown in the picture window.
1
2
31
554000
4
After the scan is complete, the screen shows all
available services for the selected range.
5
A confirmation message displays. Press c/d
to select “Yes”, and then press OK to save the
change.
NOTE
• You can directly enter the frequency instead of step 3. In
this case, select “Frequency (kHz)”, enter the number using
numeric buttons, and then press OK. Use c/d
to move between the digits.
• After performing “Carrier Scan”, the order stored by using
the “Move” function will revert to the default order.
• See page 17 for setting the PIN.
25
LC-37D44E-gb.indd 25
2008/06/16 13:38:40
DTV menu operations
Carrier Setup
System Setup
This is provided for you to rename (label), erase, or rescan carriers. “Carrier” in this context refers to a service
station that provides a set of individual services.
Configure On-Screen Display and Child Lock settings.
1
2
The On-Screen Display appearance and the position/
duration of the service banner information can be
customised.
Press c/d to select “Installation”.
Press a/b to select “Carrier Setup”, and then
press OK.
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
OSD Setup
1
2
Carrier Setup
S.No
Carrier Name
Frequency
TV
Radio
001
BBC
538000
05
03
002
BBC
546000
06
08
003
Canal+
554000
04
00
004
Digital5
592500
06
Press c/d to select “System Setup”.
Press a/b to select “OSD Setup”, and then
press OK.
OSD Setup
02
Banner timeout
4 Secs
Banner position
Bottom
Transparency
Label
Erase
Rescan
Select
Select
DTV MENU
20%
OK
DTV MENU
OK
END
END
1 To rename the selected carrier:
Select the carrier, and then press RED (Label).
The character set screen displays.
Enter a new name for the carrier. See page 23 for
details on using the character set screen.
2 To erase the selected carrier:
Select the carrier, and then press GREEN (Erase).
An icon displays indicating the carrier to be erased.
Pressing GREEN will turn the erase icon on and off.
Press OK.
A confirmation message displays.
Press c/d to select “Yes”, and then press OK.
3 To re-scan the selected carrier:
Select the carrier, and then press BLUE (Rescan).
Re-scanning starts.
A confirmation message displays.
Press c/d to select “Yes”, and then press OK.
NOTE
• After re-scanning the selected carrier, the order stored by
using the “Move” function will revert to the default order.
3
4
5
Press a/b to select the desired item.
Press c/d to select the desired parameter, and
then press OK.
A confirmation message displays. Press c/d
to select “Yes”, and then press OK to save the
change.
OSD Setup
items
Selectable items
Description
Banner
timeout
1 Sec/2 Secs/
... 7 Secs/None
Select how long the
service banner information
appears on screen.
Banner
position
Top/Bottom
Select whether the service
banner information
appears on top or bottom
of the screen.
Transparency
None/10%/20%/
...50%
Select the desired level
of On-Screen Display
transparency.
* The transparency for
Service banner displays
is not adjustable.
26
LC-37D44E-gb.indd 26
2008/06/16 13:38:43
DTV menu operations
Child Lock
Software Upgrade
This function allows TV and Radio services to be
restricted. It prevents children from watching violent or
sexual scenes that may be harmful.
1
2
Press c/d to select “System Setup”.
Press a/b to select “Child Lock”, and then
press OK.
3
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
4
Press c/d to select the desired age/rating (4
...18/Universal/Parental/X-rated/None), and then
press OK.
The software for controlling the built-in DTV decoder
can be upgraded when necessary. In Great Britain
and Sweden this can be achieved via an Over Air
Download.
Preparation
Confirm and make a note of the current software
version number as in step 2 of Version (Software
Version).
Manual upgrade
1
2
• “None”, “Children”, “Youth” and “Adult” are the ratings
used in Sweden (Please contact the organizations
concerned for details.).
1 If upgrade via Over Air Download is available
at the time:
A confirmation message appears asking you to
accept the upgrade or not.
To download now, press c/d to select “Yes”, and
then press OK. After the upgrade is completed,
the TV restarts automatically with the new software
version installed.
To postpone the download, press c/d to select
“No”, and then press OK. Enter the download time
for more convenient time as instructed.
The software upgrade will not be carried out if
there is no new software available at the specified
download time.
2 If upgrade via Over Air Download is NOT
available at the time:
A message tells you that there is no software
available to be downloaded.
Child Lock
Age/Rating
Select
7
DTV MENU
OK
END
NOTE
• “Universal” and “Parental” are the ratings used exclusively
in France.
• “X-rated” is the rating used exclusively in Spain.
• For details about ratings see page 34.
Accessories
Check the version information of the digital module and
allow it to be upgraded (when available).
Version (Software Version)
1
2
Press c/d to select “Accessories”.
Press a/b to select “Version”, and then press
OK.
• The software version is displayed.
Press c/d to select “Accessories”.
Press a/b to select “Software Upgrade”, and
then press OK. The TV checks all carriers if
there is a new software available for upgrade.
3
Check the new software version number to
confirm the successful upgrade.
Auto upgrade
1
When you tune to the service that provides the
upgrade via Over Air Download, a confirmation
message displays.
2
3
Follow the screen prompts.
Check the new software version number to
confirm the successful upgrade.
NOTE
• To scan all carriers for upgrade availability, perform the
manual upgrade.
• The software upgrade may take about 30 minutes, but may
take longer (up to 1 hour) depending on the signal status.
While updating, you cannot switch to TV or external input
mode or enter standby mode using B on the remote
control unit.
CAUTION
• Do not disconnect the AC cord when the software
upgrade is in progress, as this may cause the
upgrade to fail. If problem arises ask a qualified
service personnel before the software upgrade
period expires.
27
LC-37D44E-gb.indd 27
2008/06/16 13:38:44
DTV menu operations
Common Interface
Inserting a CA card
Check the detailed information on the CI module
(Common Interface module) and the CA card
(Conditional Access card) in use.
1
Press OK while the cursor is on “Common
Interface”.
• The CI module name is displayed.
CI Module
Module Name
IRDETO
DTV MENU
2
A single DVB Common Interface (CI) will be
implemented to allow adoption of a Conditional Access
(CA) system by means of a plug-in CA module.
Scrambled Broadcasting service can be routed via the
CA system.
If the CA system on the CI module requires a smartcard reader, this reader shall be part of the CI module.
When the compatible CA card is inserted, you can view
the programme without any operations.
OK
END
Press OK to access the CI menu.
CA card
• Detailed information on the CA card in use is
displayed.
3
Press a/b to select the item, and then press
OK.
Common
Interface Module
• Detailed information on the selected item is
displayed.
When the compatible card is not inserted:
1 Select the programme which needs the compatible
CA card.
• The caution screen appears.
2 Insert the compatible CA card.
• The caution screen disappears and you can view
the programme.
CA system supported by:
Crypto Works
Aston CAM
VIAccess
Nagra Vision
Irdeto
MR CAM
NOTE
• To view paid TV broadcasting, you need to make a
contract with a service provider.
Please contact a service provider for details.
• The Common Interface Module and the CA card are neither
supplied nor optional accessories.
Supplying power to the antenna
You may choose to supply power through the antenna
terminal. (See page 4.)
NOTE
• This function is enabled using the Analogue Menu. See
page 18 for details.
28
LC-37D44E-gb.indd 28
2008/06/16 13:38:44
Useful features (DTV)
3
About EPG
With the Electronic Programme Guide (EPG), you can
check the schedule of DTV and Radio events, view
detailed information about them, tune to an event
currently on-air and set a timer for future events.
General EPG screen
1
2
3
EPG
070
Sun 16/04/2005 07:05:11
BBC News
07:00 – 07:30
16/04/2005
• The TV will show the image in full screen.
• Selecting an event that has not yet started will
activate the EPG Timer mode instead.
NOTE
• Pressing p opens the EPG Description screen that
provides more information about the selected event. Press
p or END to exit.
Using the EPG Timer
When the Timer is set, the TV automatically tunes to a
preset TV event when its on-air time begins.
The Bold and Beautiful
***
1
2
*
Services
07:00
BBC News
The B
BBC 1
***
BBC 2
***
***
***
Page l
***
***
***
***
***
OK/Timer
***
***
Page k
OK
09:00
***
***
CBBC Channel
Select
08:00
***
Prev. Day
i+
DTV MENU
4
Next Day
END
RADIO
TV/Radio
5
1
Service name
2
Event name
* Programme information
3
Picture window
4
Service list
To watch an event currently on-air, press OK
(OK/Timer).
Press EPG.
Press a/b/c/d to select the desired event
to be preset from the Event name list, and then
press OK (OK/Timer).
• Select an event not yet started.
3
Press RED (Timer Mode), and then press a/b
to select the desired parameter (Once, Daily,
Weekly, or Monthly), and then press OK.
• Once set, the preset event is indicated with an
orange background in the EPG event name list.
• To cancel the preset, select the event to delete, press
GREEN (Delete Timer), press c/d to select “Yes”,
and then press OK.
Timer
S.No
Service name
Mode
Date
070
BBC News
Once
04/11/05 07:00 00:30
Event name list
• Shows the names of current events in a grid of
rows and columns. You can check scheduled event
information up to several days ahead, depending on
conditions.
• If a received programme does not contain a name,
either “No event name” or a blank space will be
displayed. However, the programme can still be
watched.
Using the EPG
1
Press EPG.
• Pressing RADIO will switch between DTV and Radio
mode.
2
Press a/b/c/d to access the desired service
or event.
• There is a slight lag from the time of the a/b/c/d
operations to the time the “Programme information”
and “Picture window” display is affected.
• The image shown in the picture window changes.
In the Service list:
1 Press a/b to scroll the page up/down. Or,
2 Press RED (Page l) or GREEN (Page k) to skip
to the previous/next page in one step.
In the Event name list:
1 Press c/d to scroll the page left/right. Or,
2 Press YELLOW (Prev. Day) or BLUE (Next Day) to
skip to the previous/next day in one step.
Duration
Once
Daily
Weekly
• Shows the list of all services currently available. As
you scroll down the list, the rows in the Event name
list on the right will be refreshed correspondingly.
5
Time
Monthly
Timer Mode
Select
DTV MENU
Delete Timer
OK
END
NOTE
• This function cannot be set for locked services or when
Child Lock applies. (See pages 24 and 27.)
• Up to 8 events can be preset using the Timer function.
• If you are watching another event, an alarm message
displays on the screen a few seconds before the preset
time.
• An alert message displays when the preset events overlap
one another.
• The TV power may not come on for several seconds if you
preset an event using the EPG Timer and if the AC cord
has been disconnected.
• When you set the EPG Timer, the power consumption
during the standby mode will be higher (33 W or more)
than normal.
• When the TV is turned off, the EPG Timer will not operate.
● When using the EPG Timer for recording:
• Make sure to set the timer of your recording equipment as
well.
• Do not switch channels while recording.
• If the TV is in standby mode when the preset on-air time
nears, it will output signals for recording without displaying
images on the screen.
29
LC-37D44E-gb.indd 29
2008/06/16 13:38:45
Useful features (DTV)
Using the ESG
Viewing a service banner
The Electronic Service Guide (ESG) is a simplified
version of EPG, giving you only essential information of
current events for faster access.
1
Press ESG.
A service banner shows event names, start/end time of
event, and other useful information.
1
Press p.
Service banner
• The ESG screen displays.
7
ESG
070
Sun 16/04/2005 07:05:11
16/04/2005
BBC News
07:00 – 07:30
The Bold and Beautiful
Services
Current Event
BBC News
The Bold and Beautiful
BBC 1
***
BBC 2
***
CBBC Channel
***
OK
7
BBC 1
3
i+
END
RADIO
9
1
07:45
04/11/2005
MHEG
Using the digital programme list
Select services by using the Programme List instead of
numeric buttons or P (r/s).
using
Press OK when no other menu screen is
displayed. (Except when an external input
source is selected.)
Programme List
All
S.No
Services
001
CBBC Channel
002
BBC News
003
BBC 1
004
BBC 2
005
Canal +
006
UK Gold
2
1
Logical channel number
2
Service name
3
Carrier name
4
Favourite type
5
Teletext available
6
Subtitle available
7
Lock status
8
Scrambled service
9
Multi audio status
0
Current event name
1
Current date and time
2
MHEG5 service available
2
To display more detailed information, press p
again.
• You can verify the signal strength and quality of the
selected service here.
Carrier
Freq
FFT
GI
QAM
DTV MENU
1
TV/Radio
NOTE
• Basic operation procedures are similar to EPG operations.
• ESG does not provide information about future events, or
access to Timer function.
Fav Type
8
4
0
Page k
DTV MENU
Press a/b to select a desired service, and then
press OK.
Select
2
07:00
08:00
Business news
• The TV will show the image in full screen.
1
1
BBC
Page l
Select
2
56
OK
END
RADIO
BBC
538000 kHz
8K
1/8
64
TV/Radio
Currently tuned service
Service shown in picture window
2
The screen shows the service list in either TV or
Radio mode sorted by favourite type (All, Fav 1
- 4) as configured in page 24.
3
Press a/b to select the desired service, and
then press OK.
• The image shown in the picture window changes.
4
Press END to exit the Programme List to watch
the image in full screen.
30
LC-37D44E-gb.indd 30
2008/06/16 13:38:46
Useful features (DTV)
Using the multi audio function
Change the audio mode and language for the currently
viewed service.
1
Press 2 when no other menu screen is
displayed.
Multi Audio
Audio Mode
S.No
Stereo
Language Code
Audio Type
PID
Eng
MPEG2
1211
2
Fre
MPEG2
1212
3
Ger
MPEG2
1213
4
Fin
MPEG2
1214
1
Select
DTV MENU
OK
END
2
Press c/d to select the desired audio mode
(Left, Right, L+R, Stereo), and then press b to
move down.
3
Press a/b to select the desired language
available for the service, and then press OK.
NOTE
• Once you tune to another service or the power is turned
off, the setting returns to the parameter set in the
Language menu (page 23).
NOTE
• When “Subtitle” is set to “On”, the TV will automatically
start subtitle presentation if tuned to a programme
containing subtitle data.
• When you press [ while watching DTV broadcasts, the
message “No subtitle” may appear instead of the Subtitle
OSD screen as mentioned. (This happens depending on
the type of programme and happens even when the TV is
actually receiving the subtitle data.)
In this case, press m first to activate the teletext mode,
then press [.
If you set the country setting of Auto Installation to one
of the 4 Nordic countries (Sweden, Norway, Finland or
Denmark):
• Subtitle is set to “On” when you turn off the power or
change the channel.
When another country is selected:
• Subtitle is set to “Off” when the power is turned off.
Using the MHEG5 application (UK
only)
Some services bring you programmes with the MHEG
(Multimedia and Hypermedia Expert Group) application
encoded, letting you experience DTV interactively.
When provided, the MHEG5 application will start when
you press m.
Sample MHEG5 screen
Displaying subtitles
Set the desired language for the subtitle display and
enable/disable the subtitle display.
1
Press [ when no other menu screen is
displayed.
Subtitle
Language
English
Subtitle
On
Select
DTV MENU
OK
END
2
Press a/b to select “Language”, c/d to
select the desired language available in the
stream, and then press b.
3
Select “Subtitle”, press c/d to select “On” or
“Off”.
NOTE
• When “Subtitle” is set to “On”, and the TV is tuned to a
service containing both MHEG5 and subtitle data, the
subtitle takes priority and subtitle presentation starts
automatically. In this case press m to start the MHEG5
presentation.
• A confirmation message displays.
4
Press c/d to select “Yes”, and then press OK.
31
LC-37D44E-gb.indd 31
2008/06/16 13:38:47
Appendix
Troubleshooting
Problem
Possible Solution
• No power.
• Check if you pressed B on the remote control unit. (See page 8.)
If the indicator on the TV lights up red, press B.
• Is the AC cord disconnected? (See page 4.)
• Check if you pressed a on the TV. (See page 8.)
• Unit cannot be operated.
• External influences such as lightning, static electricity, etc., may cause improper
operation. In this case, operate the unit after first turning the power off, or
unplugging the AC cord and re-plugging it in after 1 or 2 minutes.
• Remote control unit does not
operate.
•
•
•
•
• Picture is cut off.
• Is the image position correct? (See page 18.)
• Are screen mode adjustments (4:3 Mode/WSS) such as picture size made
correctly? (See pages 18 and 20.)
• Strange colour, light colour, or
dark, or colour misalignment.
•
•
•
•
• Power is suddenly turned off.
• The unit’s internal temperature has increased.
Remove any objects blocking vent or clean.
• Check the power control setting. (See page 15.)
• Is sleep timer set? Press SLEEP on the remote control unit until it sets to Off.
• No picture.
•
•
•
•
•
•
•
• No sound.
• Is the volume too low? (See pages 6 and 7.)
• Make sure that headphones are not connected. (See page 7.)
• Check if you pressed e on the remote control unit. (See page 6.)
• The DTV menu screen is displayed
in monochrome and hard to select
the item.
• Check if “Monochrome” is set to “On”. If so, set it to “Off”. (See page 14.)
• The TV sometimes makes a
cracking sound.
• This is not a malfunction. This happens when the cabinet slightly expands and
contracts according to change in temperature. This does not affect the TV’s
performance.
Are batteries inserted with polarity (e, f) aligned? (See page 5.)
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated to remote control sensor?
Adjust the picture tone. (See pages 13 and 14.)
Is the room too bright? The picture may look dark in a room that is too bright.
Check the colour system setting. (See pages 16 and 19.)
Check the HDMI Setup setting. (See page 19.)
Is connection to other components correct? (See pages 9 and 10.)
Is input signal type selected correctly after connection? (See page 19.)
Is the correct input source selected? (See page 9.)
Is non-compatible signal being input? (See page 33.)
Is picture adjustment correct? (See pages 13 and 14.)
Is the antenna connected properly? (See page 4.)
Is “On” selected in “Audio Only”? (See page 18.)
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly
delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: l20°C to e60°C.
IMPORTANT NOTE ON RESETTING THE PIN
We suggest that you remove the following instruction from the operation manual to prevent children from
reading it. As this operation manual is multilingual, we also suggest the same with each language. Keep it in a
safe space for future reference.
1
2
Repeat steps 1 to 3 in Changing the PIN. (See page 17.)
Enter “3001” to cancel out the current PIN.
• The PIN resets to the factory preset “1234”.
32
LC-37D44E-gb.indd 32
2008/06/16 13:38:49
Appendix
VGA
640 g 480
31.5 kHz
60 Hz
SVGA
800 g 600
37.9 kHz
60 Hz
✓
XGA
1024 g 768
48.4 kHz
60 Hz
✓
Communication procedure
Send the control commands from the PC via the RS232C connector.
The TV operates according to the received command
and sends a response message to the PC.
Do not send multiple commands at the same time.
Wait until the PC receives the OK response before
sending the next command.
WXGA
1280 g 768
47.7 kHz
60 Hz
✓
Command format
WXGA
1360 g 768
47.7 kHz
60 Hz
✓
PC compatibility chart
Resolution
Horizontal
Frequency
Vertical
Frequency
VESA
Standard
✓
VGA, SVGA, XGA and WXGA are registered
trademarks of International Business Machines
Corp.
NOTE
• This TV has only limited PC compatibility, correct operation
can only be guaranteed if the video card conforms exactly
to the VESA 60Hz standard. Any variations from this
standard will result in picture distortions.
• Depending on the graphics card, resolutions of 1360 g
768 may not display correctly.
RS-232C port specifications
Eight ASCII codes e CR
C1 C2 C3 C4 P1 P2 P3
Command 4-digits
Parameter 4-digits
P4
Return code
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0 – 9, g, blank, ?
Parameter
Input the parameter values, aligning left, and fill with
blank(s) for the remainder. (Be sure that four values are
input for the parameter.)
When the input parameter is not within an adjustable
range, “ERR” returns. (Refer to “Response code
format”.)
PC Control of the TV
0
• When a program is set, the TV can be controlled from
the PC using the RS-232C terminal. The input signal
(PC/video) can be selected, the volume can be adjusted
and various other adjustments and settings can be made,
enabling automatic programmed playing.
NOTE
• This operation system should be used by a person who is
accustomed to using PCs.
0
0
0
–
3
0
1
0
0
0
0
5
9
5
When “?” is input for some commands, the present
setting value responds.
RS-232C serial control cable
(cross type, commercially
available)
Communication conditions
Set the RS-232C communications settings on the PC
to match the TV’s communications conditions. The
TV’s communications settings are as follows:
Baud rate:
9,600 bps
Data length:
8 bits
Parity bit:
None
Stop bit:
1 bit
Flow control:
None
?
?
?
?
?
Response code format
Normal response
O
K
Return code (0DH)
Problem response (communication error or incorrect
command)
E
R
R
Return code (0DH)
33
LC-37D44E-gb.indd 33
2008/06/16 13:38:49
Appendix
Commands
CONTROL ITEM
POWER SETTING
INPUT SELECTION A
CHANNEL
COMMAND
_
_
_
POWER OFF
VOLUME
CONTROL ITEM
POSITION
COMMAND
PARAMETER
CONTROL CONTENTS
H P O S
*
*
*
_
H-POSITION AV (f10 – e10)
I
T
G D
_
_
_
_
INPUT SWITCHING (Toggle)
H P O S
?
?
?
?
AV (f10 – e10)
I
T
V
D
_
_
_
_
TV (CHANNEL FIXED)
V
P O S
*
*
*
_
V-POSITION AV (f10 – e10)
I
D
T
V
_
_
_
_
DTV (CHANNEL FIXED)
V
P O S
?
?
?
?
AV (f10 – e10)
I
A
V
D
*
_
_
_
EXT1 – 7 (1 – 7)
C
L
C K
*
*
*
_
CLOCK (0 - 180)
I
A
V
D
?
?
?
?
1 to 7, ERR (TV/DTV)
C
L
C K
?
?
?
?
0 to 180
D C C H
*
*
_
_
TV DIRECT CHANNEL (1 – 99)
P H S
E
*
*
_
_
PHASE (0 – 64)
D C C H
?
?
?
?
1 to 99
P H S
E
?
?
?
?
0 to 64
C H U P
_
_
_
_
CHANNEL UP
W
I
D
E
0
_
_
_
WIDE MODE (Toggle)
C H D W _
_
_
_
CHANNEL DOWN
W
I
D
E
1
_
_
_
NORMAL (AV)
D
*
*
_
THREE DIGIT DTV DIRECT
CHANNEL (1–999) *User for
LC-37D44E
W
I
D
E
2
_
_
_
ZOOM 14:9 (AV)
W
I
D
E
3
_
_
_
PANORAMA (AV)
FOUR DIGIT DTV DIRECT
CHANNEL (1–9999) *User for
LC-37D44S
W
I
D
E
4
_
_
_
FULL (AV)
W
I
D
E
5
_
_
_
CINEMA 16:9 (AV)
W
I
D
E
6
_
_
_
CINEMA 14:9 (AV)
W
I
D
E
9
_
_
_
NORMAL (PC)
D
AV MODE SELECTION
CONTROL CONTENTS
0
T
D T
INPUT SELECTION B
PARAMETER
P O W R
T
V
V
D
*
D *
V
D
*
?
*
?
?
*
?
WIDE MODE
1 to 999 *User for LC-37D44E
1 to 9999 *User for LC-37D44S
D
T
U P
_
_
_
_
DTV CHANNEL UP
W
I
D
E
1
0
_
_
FULL (PC)
D
T
D W _
_
_
_
DTV CHANNEL DOWN
W
I
D
E
?
?
?
?
1 to 10
I
N P
1
0
_
_
_
EXT1 (Y/C)
M U
T
E
0
_
_
_
MUTE (Toggle)
I
N P
1
1
_
_
_
EXT1 (CVBS)
MUTE
M U
T
E
1
_
_
_
MUTE ON
I
N P
1
2
_
_
_
EXT1 (RGB)
M U
T
E
2
_
_
_
MUTE OFF
I
N P
1
?
?
?
?
0 to 2
M U
T
E
?
?
?
?
1 to 2
I
N P
2
0
_
_
_
EXT2 (Y/C)
A C D
V
0
_
_
_
SURROUND (Toggle)
I
N P
2
1
_
_
_
EXT2 (CVBS)
A C D
V
1
_
_
_
SURROUND ON
I
N P
2
2
_
_
_
EXT2 (RGB)
A C D
V
2
_
_
_
SURROUND OFF
I
N P
2
?
?
?
?
0 to 2
A C D
V
?
?
?
?
1 to 2
I
N P
3
0
_
_
_
EXT3
AUDIO CHANGE
A C H A
_
_
_
_
I
N P
4
0
_
_
_
EXT4
SOUND SELECT (ST/Bilingual/
mono)
I
N P
5
0
_
_
_
EXT5 (COMPONENT)
SLEEP TIMER
O
F
T M 0
_
_
_
OFF
I
N P
6
0
_
_
_
EXT6 (HDMI)
O
F
T M 1
_
_
_
30 m
I
N P
7
0
_
_
_
EXT7 (HDMI)
O
F
T M 2
_
_
_
1 h 00 m
A
V M D
0
_
_
_
AV MODE SELECTION (Toggle)
O
F
T M 3
_
_
_
1 h 30 m
A
V M D
1
_
_
_
STANDARD
O
F
T M 4
_
_
_
2 h 00 m
A
V M D
2
_
_
_
SOFT
O
F
T M 5
_
_
_
2 h 30 m
A
V M D
3
_
_
_
ECO
O
F
T M ?
?
?
?
0 to 150
A
V M D
4
_
_
_
USER
T
E
X
T
0
_
_
_
TEXT OFF
A
V M D
5
_
_
_
DYNAMIC
T
E
X
T
1
_
_
_
TEXT CHANGE (Toggle)
A
V M D
?
?
?
?
1 to 5
T
E
X
T
?
?
?
?
0 to 1
D C P G
*
*
*
_
DIRECT PAGE JUMP (100 – 899)
D C P G
?
?
?
?
100 to 899
SURROUND
TEXT
V O
L M
*
*
_
_
VOLUME (0 – 60)
V O
L M ?
?
?
?
0 to 60
NOTE
• If an underbar (_) appears in the parameter column, enter a space.
• If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
Rating table for Child Lock
Broadcasted
rating
AGE
Useradjusted rating
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Universal
✔
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Parental
✔
✔
✔
✔
✔
—
—
—
—
—
—
—
—
—
—
X-rated
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Broadcasted
rating
Useradjusted rating
Universal
Parental
X-rated
Universal
—
—
—
Parental
✔
—
—
X-rated
✔
✔
—
34
LC-37D44E-gb.indd 34
2008/06/16 13:38:51
Appendix
Specifications
Item
37o LCD COLOUR TV, Model: LC-37D44E, LC-37D44S
LCD panel
37o Advanced Super View & BLACK TFT LCD
Resolution
1,049,088 pixels (1,366 g 768)
Video Colour System
PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV
Function
TV-Standard
Receiving
Channel
Analogue
CCIR (B/G, I, D/K, L, L’)
Digital
DVB-T (2K/8K OFDM)
VHF/UHF
E2–E69ch, F2–F10ch, I21–I69ch, IR A–IR Jch, (Digital: E5–E69ch)
CATV
Hyper-band, S1–S41ch
TV-Tuning System
STEREO/BILINGUAL
Auto Preset 999 ch: non-Nordic / 9999 ch: Nordic (ATV: 99 ch), Auto Label, Auto Sort
NICAM/A2
Brightness
450 cd/m2 (in Dynamic Mode)
Backlight life
60,000 hours (in Standard Mode)
Viewing angles
H : 176° V : 176°
Audio amplifier
10W g 2
Speaker
(100 mm g 35 mm) g 2
Terminals
Antenna
UHF/VHF 75q Din type (Analogue & Digital)
RS-232C
9 pin mini D-sub
EXT 1
SCART (AV input, Y/C input, RGB input, TV output)
EXT 2
SCART (AV input/output, Y/C input, RGB input, AV Link)
EXT 3
S-VIDEO (Y/C input), RCA pin (AV input)
EXT 4
Ø 3.5 mm jack (Audio input), 15 pin mini D-sub (PC)
EXT 5
Audio in, Component in
EXT 6
HDMI, Ø 3.5 mm jack (Audio input)
EXT 7
HDMI
C. I. (Common Interface)
EN50221, R206001
OUTPUT
RCA pin (Audio)
Headphones
Ø 3.5 mm jack (Audio output)
Power Requirement
AC 220–240 V, 50 Hz
Power Consumption
146 W (0.9 W Standby) (Method IEC60107)
Weight
14.5 kg (Display only), 17.0 kg (Display with stand)
Operating temperature
0°C to k40°C
• As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
NOTE
• Refer to inside back cover for dimensional drawings.
Optional accessory
The listed optional accessories are available for the
LCD colour TV. Please purchase them at your nearest
shop.
• Additional optional accessories may be available in near
future. When purchasing, please read the newest catalogue
for compatibility and check the availability.
Part name
Wall mount bracket
(LC-37D44E, LC-37D44S)
Part number
AN-37AG5
35
LC-37D44E-gb.indd 35
2008/06/16 13:38:52
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that
requires proper treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used
electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your
local retailer may also take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
Attention: Your product
is marked with this
symbol. It means that
used electrical and
electronic products
should not be mixed
with general household
waste. There is a
separate collection
system for these
products.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately
beforehand according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment,
recovery and recycling and thus prevent potential negative effects on the environment and human health which
could otherwise arise due to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of
disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you
don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.
sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged
for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by
your local collection facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used
products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of
disposal.
The battery supplied with this product contains traces of Lead.
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation. Please contact your local authority for details on the collection and recycling
schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method of disposal of the used battery.
36
LC-37D44E-gb.indd 36
2008/06/16 13:38:52
LC-37D44E/LC-37D44S
89.6
89,6
903.8
903,8
95.3
95,3
52.0
52,0
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a
safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric
shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
100.0
100,0
200.0
200,0
DANGER:
465.0
465,0
200.0
200,0
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
or )5) and of the same rating as above,
which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains
plug and fit an appropriate type.
366.9
366,9
463.8
463,8
637.0
637,0
585.0
585,0
824.4
824,4
270.0
270,0
Printed on environmentally friendly paper
Auf ökologischem Papier gedruckt
Imprimé sur papier écologique
Stampato su carta ecologica
Afgedrukt op ecologisch papier
Impreso en papel ecológico
Impresso sobre papel ecológico
PIN
Printed in Poland
Gedruckt in Polen
Imprimé en Pologne
Stampato in Polonia
Gedrukt in Polen
Impreso en Polonia
Impresso na Polónia
TINS-D792WJZZ
1
08P07-PL-NG
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
ESPAÑOL
OPERATION MANUAL / BEDIENUNGSANLEITUNG / MODE D'EMPLOI / MANUALE DI ISTRUZIONI / GEBRUIKSAANWIJZING / MANUAL DE MANEJO /
MANUAL DE OPERAÇÃO
SHARP CORPORATION
PORTUGUÊS
D792WJZZ
Sonninstraße 3, D-20097 Hamburg
LCD COLOUR TELEVISION
LCD-FARBFERNSEHGERÄT
TÉLÉVISEUR COULEUR À ÉCRAN
CRISTAUX LIQUIDES (LCD)
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
TELEVISOR DE CRISTAL LÍQUIDO OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
ENGLISH
LC-37D44E
LC-37D44S
SHARP ELECTRONICS (Europe) GmbH
LC-37D44E
LC-37D44S