Register your product and get support at
www.philips.com/welcome
AZ1326
EN
User manual
1
Important
Safety
a
Read these instructions.
b
Keep these instructions.
c
Heed all warnings.
d
Follow all instructions.
e
Do not use this apparatus near water.
f
Clean only with dry cloth.
g
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
h
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
i
For countries with a polarized mains, do not defeat the
safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement
of the obsolete outlet.
Caution: To prevent electric shock, match the wide blade
of the plug to the wide slot, fully insert.
j
Protect the power cord from being walked on or
pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
k
Only use attachments/accessories specified by the
manufacturer.
l
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer or sold with the
apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from tipover.
m
Unplug this apparatus during lightning storms or when
unused for long periods of time.
n
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
o
Battery usage CAUTION – To prevent battery leakage
which may result in bodily injury, property damage, or
damage to the unit:
•
•
•
Install all batteries correctly, + and - as marked on
the unit.
Do not mix batteries (old and new or carbon and
alkaline, etc.).
Remove batteries when the unit is not used for a
long time.
p
Apparatus shall not be exposed to dripping or splashing.
q
Do not place any sources of danger on the apparatus
(e.g. liquid filled objects, lighted candles).
r
This product may contain lead and mercury. Disposal of
these materials may be regulated due to environmental
considerations. For disposal or recycling information,
please contact your local authorities or the Electronic
Industries Alliance: www.eiae.org.
Safety-Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved 13 Amp plug. To
change a fuse in this type of plug proceed as follows:
a
Remove fuse cover and fuse.
b
Fix new fuse which should be a BS1362 3 Amp, A.S.T.A.
or BSI approved type.
c Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 3
Amp. If a plug without a fuse is used, the fuse at the distribution
board should not be greater than 3 Amp.
Note: The severed plug must be disposed off to avoid a possible
shock hazard should it be inserted into a 13 Amp socket
elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following
code: blue = neutral (N), brown = live (L).
As these colours may not correspond with the colour markings
identifying the terminals in your plug, proceed as follows:
• Connect the blue wire to the terminal marked N or
coloured black.
• Connect the brown wire to the terminal marked L or
coloured red.
• Do not connect either wire to the earth terminal in the
plug, marked E (or e) or coloured green (or green and
yellow).
Before replacing the plug cover, make certain that the cord grip
is clamped over the sheath of the lead - not simply over the
two wires.
Copyright in the U.K.
Recording and playback of material may require consent. see
Copyright Act 1956 and The performer’s Protection Acts 1958
to 1972.
Warning
• Never remove the casing of this CD Soundmachine.
• Never lubricate any part of this CD Soundmachine.
• Never place this CD Soundmachine on other electrical
equipment.
• Keep this CD Soundmachine away from direct sunlight,
naked flames or heat.
• Never look into the laser beam inside the CD
Soundmachine.
• Ensure that you always have easy access to the power cord,
plug or adaptor to disconnect the CD Soundmachine from
the power.
Notice
This product complies with the radio interference requirements
of the European Community.
This product complies with the requirements of the following
directives and guidelines: 2004/108/EC, 2006/95/EC.
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Lifestyle may void the
user’s authority to operate the equipment.
The making of unauthorized copies of copy-protected material,
including computer programs, files, broadcasts and sound
recordings, may be an infringement of copyrights and constitute
a criminal offence. This equipment should not be used for such
purposes.
Recording and playback of material might require consent. See
Copyright Act 1956 and The Performer’s Protection Acts 1958
to 1972.
This CD Soundmachine includes this label:
Disposal of your old product
Your product is designed and manufactured with highly quality
material and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to
a product, it means the product is covered by the European
Directive 2002/96/EC.
Please inform yourself about the local separate collection system
for electrical and electronic products.
Please act according to your local rules and do not dispose your
old products with your normal household waste. The correct
disposal of your old product will help prevent potential negative
consequences for the environment and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried
to make the packaging easy to separate into three materials:
cardboard (box), polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can be recycled and
reused if disassembled by a specialized company. Please observe
the local regulations regarding the disposal of packaging materials,
exhausted batteries and old equipment.
2
Your CD Soundmachine Dynamic
Bass Boost
Congratulations on your purchase, and welcome to Philips! To
fully benefit from the support that Philips offers, register your
product at www.Philips.com/welcome.
Introduction
With the CD Soundmachine, you can:
• play audio discs
• listen to FM/MW radio
• program the play sequence of tracks
• enhance the sound with the Dynamic Bass Boost feature.
What’s in the box
Check and identify the contents of the package:
• CD Soundmachine
• AC power cord
• User Manual
Overview of the main unit
f
a
g
h
b
i
c
j
d
k
d
l
m
e
o
n
a
VOL+/• Adjust volume level
b
MP3 LINK
• Socket for connecting an external device
c
•
d
e
f
Start or pause CD play
TUNING
/
• Tune to radio stations
• Select the previous/next track
• Search backward/forward
ALBUM/PRESET +/For MP3-CDs: skip to the next/previous album in
an MP3-CD
• For radio: select a preset station
•
Telescopic antenna
Adjust FM reception
•
g
LIFT TO OPEN
• Open/close the CD compartment
h
MUTE
• Mute or restore the volume.
i
DBB
j
Source selector: CD, FM, MW,MP3 LINK
• Select CD, FM, MW, or MP3 source
k
l
•
•
•
Turn the bass enhancement on/off
Stop CD play
Erase a CD program
PROG
• For MP3-CDs: program tracks and browse the
program
• For radio: store preset stations
m
MODE
• Select a play mode: REPEAT or SHUFFLE
n
AC MAINS~
• Socket for the power cord
o
ON/OFF
•
Turn the CD Soundmachine on or off
3
Get started
Caution
• Use the controls only as stated in this user manual.
• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial
number of your CD Soundmachine. The model number and
serial number are on the bottom of your CD Soundmachine.
Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install batteries
Note
• You can use both batteries and AC power as power supply
of this CD Soundmachine.
• Batteries are not supplied with the accessories.
1
Open the battery compartment.
6 x 1.5V R-14/UM-2/C-cell
2
Insert 6 x 1.5V R14/UM-2/C-cell batteries with correct
polarity (+/-) as indicated.
3
Close the battery compartment.
Connect AC power
Warning
• Risk of product damage! Ensure that the power supply
•
voltage corresponds to the voltage printed on the back or
the underside of the CD Soundmachine.
Risk of electric shock! When you unplug the AC adaptor,
always pull the plug from the socket. Never pull the cord.
Note
• Install the unit near the power supply socket and where the
AC power plug can be easily reached.
1
Connect the power cord to the AC MAINS~ socket on
the CD Soundmachine and to the power supply socket.
•
To switch the CD Soundmachine off completely,
disconnect the power cord from the power supply
socket.
Tip
• To save energy: After use, set the switch to OFF.
4
Use your CD Soundmachine
Play a CD
Note
• You cannot play CDs encoded with copyright protection
technologies.
You can play commercially available audio CDs:
• CD-Recordables (CD-R)
• CD-Rewritables (CD-RW)
• MP3-CDs
1
Switch the source selector to CD.
2
Lift the lid of the CD compartment.
3
Insert a CD with the printed side facing up.
4
Close the CD lid gently.
»
5
Press
»
•
•
The total number of tracks is displayed.
[
to start play.
] is displayed.
To pause CD play, press
To resume CD play, press
.
again.
•
To stop CD play, press
.
Select a track
1
During play, press TUNING
/
to select a track.
Select an album
For MP3-CDs only.
1
During play, press ALBUM/PRESET +/- to select an album.
Find a passage within a track
1
During play, press and hold TUNING
»
2
/
.
The CD is played at high speed and with reduced volume.
Release TUNING
/
to resume normal play.
Tip
• When search reaches the end of the last track, the CD
stops.
Select play modes
Repeat play
You can repeat a track, an MP3 album, a disc, or a program.
• [ ] – Repeat a track
• [ ALB] – Repeat an album
• [ ALL] – Repeat an entire CD/program
1
•
During play, press MODE repeatedly until the display
shows the repeat icon.
• Repeat a track.
•
Repeat an album.
•
Repeat a program.
To stop repeat play, press MODE repeatedly until the
repeat icon is no longer displayed.
Shuffle play
You can play all tracks in random order.
1
During play, press MODE repeatedly until the display
shows the shuffle icon.
•
To stop shuffle play, press MODE again.
Program play sequence
You can store up to 20 tracks in the desired sequence.
1
In stop mode, press PROG to start to program play
sequence.
»
[PROG] and [P01] are displayed.
2
For MP3-CDs: press ALBUM/PRESET +/- to select an
album.
3
Press TUNING
4
Press PROG to store the track.
»
5
/
to select a track.
[PROG] and [P02] are displayed.
Repeat steps 2 to 4 to select and store all tracks.
»
6
When all 20 tracks are stored, no more tracks can be selected
and the display shows [PROG] and [---].
To play program, press
.
In stop mode, press PROG repeatedly to browse
stored tracks.
• To cancel program, press twice.
•
Tip
• When program play stops, the CD Soundmachine returns
to normal play. To play program again, repeat steps 1 to 6.
Listen to radio
1
Switch the source selector to FM or MW.
2
Press and hold TUNING
the display starts to run.
»
3
•
/
until the frequency in
When the CD Soundmachine finds a station with strong
signals, it begins to broadcast that station.
Repeat step 2 until you find a station.
To tune to a weak station, press TUNING
repeatedly until you find optimal reception.
/
Tip
• To improve FM reception, you can extend, incline or turn
the telescopic antenna for best reception.
• To improve MW reception, turn the CD Soundmachine to
face a different direction.
Program radio stations
You can program up to 20 preset radio stations for later
listening.
Automatic programming
Automatic programming starts at preset station 1 and all your
former preset stations are overwritten.
1
Press and hold PROG.
»
All available stations are programmed.
Manual programming
1
Tune to a radio station.
2
Press PROG to start programming.
3
Press ALBUM/PRESET +/- to allocate a number to this
station and press PROG.
4
Repeat step 1-3 to program other stations.
Tip
• You can overwrite a preset station by programming
another frequency in the same number.
Tuning to preset radio stations
1
Press ALBUM/PRESET +/- repeatedly until the desired
station is displayed.
5
Troubleshooting
Warning
• Never remove the casing of this CD Soundmachine.
To keep the warranty valid, never try to repair the system
yourself.
If you encounter problems when using this CD Soundmachine,
check the following points before requesting service. If
the problem remains unsolved, go to the Philips web site
(www.Philips.com/support), or contact Philips (see Contact
information). When you contact Philips, ensure that your CD
Soundmachine is nearby and the model number and serial
number are available.
No power
• Ensure that the Mains cord is connected securely.
• Ensure that there is power at the AC Mains.
• Ensure that the batteries are inserted correctly.
No sound
•
•
Adjust the volume.
Ensure that the track played is of a compatible format.
Display does not function properly./No reaction to operation
of any of the controls.
1
Disconnect the AC power cord.
2
Connect the AC power cord after a few seconds.
Cannot play disc
•
Ensure that the disc label is inserted with the printed side facing up.
•
•
•
•
•
Wipe the disc with fibre cleaning cloth from the centre to the edge
in a straight line.
This disc may be defective. Play another disc.
Ensure that the CD is a finalised CD/CD-R/CD-RW.
Ensure that the laser lens is clean.
Ensure that the CD is not encoded with copyright protection
technologies.
The CD skips tracks
•
•
Ensure that the CD is not damaged or dirty.
Ensure that program/shuffle mode is deactivated.
6
Product information
Note
• Product information is subject to change without prior
notice.
Dimensions
(W x H x D)
290 x 146 x 243 mm
11.42 x 5.75 x 9.57 inches
Weight
1.5 kg
3.3 pound
Power supply
DC 9V 1.5 A
AC 230V
Power consumption
Active <12 W
Standby 2 W
Power output
2 x 1 W RMS
Operating temperature -10 °C - 50 °C
range
14 °F -122 °F
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
Printed in China