D-Link DFM-562IS modems

D-Link DFM-562IS HSFi PCI Modem
User’s Guide
D-Link DFM-562IS
HSFi PCI MODEM
Conexant HSFi
User’s Guide
1
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
FCC Requirements
This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a
label that contains, among other information, the FCC Registration Number and Ringer
Equivalence Number (REN) for this equipment. IF REQUESTED. THIS INFORMATION
MUST BE GIVEN TO THE TELEPHONE COMPANY.
The REN is useful to determine the quantity of devices you may connect to your telephone line
and still have these entire devices ring when your telephone number is called In most. But not
all areas the sum of the REN’s of all devices connected to one line should not exceed five (5.0).
To be certain of the number of devices you may connect to your line. As determined by the
REN. You should contact your local telephone company to determine the maximum REN of
the area you are calling from. If your telephone equipment causes harm to the telephone
network. The Telephone Company may discontinue your service temporally. If possible, they
will notify you in advance. But if the advanced notice is failed, you will be notified as soon as
possible. You will be informed of your right to file a complaint with the FCC.
Your telephone company may change in its facilities, equipment, operations or procedures that
could affect the proper functions of your equipment. If this occurs, you will be notified in
advance to give you an opportunity to maintain uninterrupted telephone service.
If you experience trouble with this telephone equipment, please contact the following address
and phone number for information on obtaining service or repairs. The Telephone Company
may ask you to disconnect this equipment from the network until the problem is solved or until
that the equipment is not detected malfunctioning. This equipment may not be used on coin
service provided by the Telephone Company. Connection to party lines is subject to state
Tariffs.
Federal Communications Commission
Radio Frequency Interference Statement.
Note: This equipment has been tested and found to comply with the limitation for a lass B
digital device pursuant to Part 15 of the FCC Rules. These restrictions are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
residential installation. This equipment generates, uses, and can radiate radio frequency
energy and if not installed and used in accordance with the instruction manual may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If the equipment does cause harmful
interference to radio or television reception, which can be determine by tuning the equipment
off and on, the user is suggested to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the distance between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected. Consult the dealer or an experienced radio TV technician for help.
Notices:
(1) The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
(2) Shielded interface cables and AC power cord if any must be used in order to comply with
the emission limits.
Notices to Australian users:
The modem card must only be used in a data terminal equipment (DTE) e.g. computer, that has
a screw down cover (lid). As unsafe voltages (TNV) exist on the modem card, disconnect the
modem card from the telephone line while the cover (lid) of the DTE (computer) is removed.
Installation of the modem card in a DTE (computer) which does not require a tool to open the
cover (lid) will render the permit void.
Disconnect the telephone line before opening the cover (lid) of the DTE (computer). Do not
connect the customer equipment to the telephone line while the cover (lid) of the DTE
(computer) is open.
2
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
WARNING
ONLY CONNECT EQUIPMENT WITH A TELECOMMUNICATIONS
COMPLIANCE LABEL
WARNING
FOR SAFETY REASONS, ONLY CONNECT EQUIPMENT WITH A
TELECOMMUNICATIOS COMPLIANCE LABEL. THIS INCLUDES
CUSTOMER EQUIPMENT PREVIOUSLY LABELLED
PERMITTED OR CERTIFIED.
Modems connected to the Australian telecommunications network must be marked in
accordance with the Labeling Notice. This modem has been specifically configured to ensure
compliance with the ACA Standards. Do not adjust your modem or software outside the
values indicated as below. To do so would result in your modem being operated in a
non-compliant manner.
Modem Commands:
Default
Permissible Range
Command
ATA
Do not use
ATB
B0
Do not set to B1
AT&G
&G0
&G2
AT&P
&P0
&P1
ATSn
see table below
Default
Permissible Range
S register
s6
2
2 to 6
Call Attempts/Retries:
Applications software shall be configured so that no more than 3 attempts are made to
establish a connection to a given number (Note: if the modem can detect service tones, up to
10 attempts can be made). If the call sequence is unsuccessful, there shall be a delay of at
least 30 minutes before attempting to call the number again.
Failure to set the modem and any application software used with the modem, to the values
shown as above will result in the modem being operated in a non-compliant manner.
Consequently, this would be in violation of the Labeling Notice for this equipment, and the
Telecommunications ACT 1997 prescribes penalties for the connection of non-compliant
equipment.
3
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
CONTENTS
Chapter 1 Introduction....................................................... 5
1.1 Introduction.......................................................................................5
1.2 Packing..............................................................................................5
1.3 Features .............................................................................................5
Chapter 2 Specifications..................................................... 6
Chapter 3 Hardware Installation ..................................... 7
Chapter 4 Software Installation ........................................ 8
4.1 Windows 95.......................................................................................8
4.2 Windows 98.....................................................................................11
4.3 Windows ME...................................................................................19
4.4 Windows NT 4.0 .............................................................................23
4.5 Windows 2000.................................................................................38
4.6 Windows XP ...................................................................................42
Chapter 5 Select Modem Country................................... 44
5.1 Windows 95.....................................................................................44
5.2 Windows 98/ME .............................................................................46
5.3 Windows 2000.................................................................................49
5.4 Windows NT4.0 ..............................................................................50
5.5 Windows XP ...................................................................................53
Chapter 6 Diagnostics....................................................... 56
6.1 Windows 95/98/ME ........................................................................56
6.2 Windows 2000.................................................................................58
6.3 Windows XP ...................................................................................61
Chapter 7 Uninstalling Procedures ................................. 64
7.1 Windows 95.....................................................................................64
7.2 Windows 98/ME .............................................................................66
7.3 Windows NT4.0 ..............................................................................68
7.4 Windows 2000.................................................................................70
7.5 Windows XP ...................................................................................72
4
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
Chapter 1 Introduction
1.1 Introduction
Thank you for selecting the D-Link DFM-562IS HSFi PCI Modem . It
provides the modem function under Windows GUI interface supplied by Windows.
All of the above advances come from the special design of Windows control function,
which move the dominating of control signal of modem from modem body to the
Windows system. Therefore and it makes the D-Link DFM-562IS HSFi PCI Modem
work more smoothly than traditional RS-232 Modem. If you are just working under
Windows system, D-Link DFM-562IS HSFi PCI Modem is the best product you
need to work with.
1.2 Packing
The D-Link DFM-562IS HSFi PCI Modem series include the following accessories:
Internal modem card
User’s manual
Driver and Application Software (CD-ROM)
Phone Cord
1.3 Features
Modem (controlless)
ITU 56K V.92,V.90 Standard
PCI V2.1 compliant
Windows 95/98/ME/NT4.0/2000/XP compatible
Software upgradeable
5
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
Chapter 2 Specifications
Specifications:
Line data rate
Modem protocol
Chip Set
Interface
Fax Compatibility
Error Correction
Data Compression
Max. DTE data rate
PnP
Modem operation
Line interface
Software Compatibility
System Requirement
System compatibility
56000,54000,52000,50000,48000,46000,44000,42000,
40000,38000,36000,34000,33600,31200,28800,26400,
24000,19200,16800,14400,12000,9600,7200,4800,2400
,1200,600,300
ITU-T V.92,V.90/K56flex/ITU-T
V.34bis/V.34/V.32bis/V.32/V.22bis/V.22/V.21/V.23
Bell 212A/103,V.80,V8/V.8bis
Conexant HSFi-CX11251-11
PCI BUS
14.4k bps Send/Receiver G3 compatible
MNP2-4,V.42
V.44 , MNP 5, V.42bis
115200bps
Build in
Dial up
RJ-11 Line/Phone
AT command set Compatible
Pentium CPU 233+, 64M RAM+, L2 cache 256K
OS Windows 95/98/ME/NT4.0/2000/XP
6
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
Chapter 3 Hardware Installation
1. Remove the computer’s case.
2. Insert the modem card into a spare PCI expansion slot.
3. Close the case.
4. Unplug the telephone from the wall socket, then plug the telephone into the
socket on the back of the modem marked PHONE.
5. Plug the phone cord supplied into the socket on the back of the modem marked
LINE.
6. Plug the other end of the cord into the wall socket.
7. Proceed to Software installation.
7
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
Chapter 4 Software Installation
Power on your computer then start Windows 95/98//ME/NT4.0/2000/XP.
Windows 95/98/ME/NT4.0/2000/XP will detect the modem automatically.
4.1 Windows 95 B (OSR2)
1.
When you see the message of PCI Communication Device shown on the screen.
However, it may vary with the type of the Mother board. Please insert the driver
CD supplied and click Next.
8
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
2.
Click Other Locations… to search for the correct driver and location.
3.
Select the location of F:\Win95 (F is the letter of your CD-ROM drive) and click
OK.
9
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
4.
Windows 95 will find the driver shown as below, then click Finish.
5.
Click OK.
6.
Type F: \WIN95 or use the Browse to find the location of the modem driver,
then click OK.
10
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
4.2 Windows 98
1.
The message of PCI Commucication Device will appear. However it may vary
with the type of your mother board. Please insert the driver CD supplied and
click Next.
2.
Select Search for the best driver for your device [Recommended] and click
Next.
11
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Select Specify a location and type F:\Win98 (F is the letter of CD-ROM drive )
and click Next to continue.
4.
Windows will find the driver for D-Link DFM-562IS HSFi PCI Modem and
click Next.
12
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
5.
Click Finish to end this installation procedure.
6.
The message of D-Link DFM-562IS HSFi PCI Modem will appear. However
it may vary with the type of your mother board. Please insert the driver CD
supplied and click Next.
13
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
7.
Select Search for the best driver for your device [Recommended] and click
Next.
8.
Select Specify a location and type F:\Win98 (F is the letter of CD-ROM drive )
and click Next to continue.
14
D-Link DFM-562IS HSFi PCI Modem
9.
User’s Guide
Windows will find the driver for D-Link DFM-562IS HSFi PCI Modem and
click Next.
10. Click Finish to end this installation procedure.
15
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
11. The message of Wave Device for Voice Modem will appear. However it may
vary with the type of your mother board. Please insert the driver CD supplied
and click Next.
12. Select Search for the best driver for your device [Recommended] and click
Next.
16
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
13. Select Specify a location and type F:\Win98 (F is the letter of CD-ROM drive )
and click Next to continue.
14. Windows will find the driver for Voice Modem Serial Ware Device and click
Next.
17
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
15. Click Finish to end this installation procedure.
18
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
4.3 Windows ME
1.
The message of PCI Commucication Device will appear. Select Specify the
location of the driver [Advanced] and click Next.
2.
Select Search for the best driver for your device. [Recommended], then Select
Specify a location and type I:\WinME ( I is the letter of CD-ROM drive ) and
click Next to continue.
19
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Windows will find the driver for D-Link DFM-562IS HSFi PCI Modem and
click Next.
4.
Click Finish to end this installation procedure.
20
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
5.
The message of Modem Device will appear. Select Specify the location of the
driver [Advanced] and click Next.
6.
Select Search for the best driver for your device. [Recommended], then Select
Specify a location and type I:\WinME (I is the letter of CD-ROM drive ) and
click Next to continue.
21
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
7.
Windows will find the driver for D-Link DFM-562IS HSFi PCI Modem and click
Next.
8.
Click Finish to end this installation procedure.
22
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
4.4 Windows NT 4.0
1.
Please insert the driver CD supplied. Then click Start \ Run on the desktop and
use Browse to open the file of F:\WinNt4\Setup.exe (F is the letter of CD-ROM
drive), then click OK.
2.
Click Next.
23
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Click Next.
4.
The message of The modem driver was installed successfully and clicks
Finish.
Note: You must restart your computer to enable the modem driver.
24
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
5.
If you want to use Dial-Up Networking, please do as following. After restarting your
computer, click Start \ Settings \ Control Panel on the desktop and double-click on the
Network icon.
6.
Click on the Services tab and select Remote Access Service, then click
Properties. If you can’t see Remote Access Service on the screen click Add to
install Remote Access Service.
25
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
7.
Click on the Add button to add the D-Link DFM-562IS HSFi PCI Modem. If
there is any other modem in the list, please click Remove first.
8.
Select COM3-D-Link DFM-562IS HSFi PCI Modem, then click OK.
9.
Click Configure to configure port usage.
26
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
10. Select Dial out only for Port Usage and click OK to confirm the settings.
11. Click Network to configure the network.
12. Select TCP/IP for Dial out Protocols and click OK to confirm the settings.
27
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
13. Click Continue to complete the setup.
14. Click Close.
28
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
15. Click Yes to restart your computer.
16. After restarting your computer, please double-click on the My Computer icon
on the desktop and double-click on the Dial-Up Networking icon.
17. If your phonebook is empty, please click OK to add an entry.
29
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
18. You may use the name provided or enter a different one, then click Next.
19. Select The non-Windows NT server I am calling… then click Next.
30
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
20. Enter the Phone number of your local ISP and click Next.
21. Select Point-to-Point Protocol (PPP) and click Next.
31
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
22. Select None under normal condition, or consult with your local ISP for other
choice and click Next to continue.
23. Enter your IP address if you have a fixed one or leave the value: 0.0.0.0, then click Next.
32
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
24. Enter the IP addresses of a DNS and/or WINS server for your local ISP or
set 0.0.0.0 if you are not sure. Then click Next to continue.
25. Click Finish to save the settings for the new phonebook entry.
33
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
26. Click on the More buttons and select Edit entry and modem properties….
27. Select D-Link DFM-562IS HSFi PCI Modem (COM3) from Dial using list and
click on the Configure button.
34
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
28. Enable all the Hardware Features and select 115200 from Initial speed list,
then click OK.
29. Click on the Server tab and enable three options of TCP/IP, Enable software
compression and Enable PPP LCP extensions.
35
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
30. Click on the Security tab and enable the option: Accept any authentication
including clear text, then click OK.
31. The phonebook entry has been edited, click Dial to connect to.
36
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
32. Enter User name and Password and click OK, and the modem will dial out to
your ISP and get a connection.
37
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
4.5 Windows 2000
1.
Windows will detect the modem automatic; please insert the driver CD supplied
and clicks Next to continue.
2.
Select Search for a suitable driver for my device [recommended], and click
Next.
38
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Select Specify a location, then click Next to continue.
4.
Please type G:\Win2K (G is the letter of your CD-ROM driver), then click OK to
continue.
39
D-Link DFM-562IS HSFi PCI Modem
5.
Click Next to continues.
6.
Click Yes.
User’s Guide
40
D-Link DFM-562IS HSFi PCI Modem
7.
User’s Guide
Click Finish to end procedure.
41
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
4.6 Windows XP
1.
. Select Install from a list specific location [Advanced], then click Next.
2.
Select Include this location in this search, then click Next .
42
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Click Continue Anyway.
4.
This installation has been done; click Finish to end this procedure.
43
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
Chapter 5 Select Modem Country
5.1 Windows 95
1.
Move your courser as following sequence Start\Settings\Control Panel and
click Control Panel. Then double-click on the System icon.
2.
Click Device Manager tab and select D-Link DFM-562IS HSFi PCI Modem,
then click Properties.
44
D-Link DFM-562IS HSFi PCI Modem
3.
User’s Guide
Select country form the list , then click OK.
45
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
5.2 Windows 98/ME
1.
Move your courser as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Modems icon.
2.
Select General and click D-Link DFM562IS HSFi PCI Modem, then click
Dialing Properties.
46
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3. In the I am in this country/region, to select United States of America and click
Apply.
4.
Click OK.
47
D-Link DFM-562IS HSFi PCI Modem
5.
User’s Guide
Click OK to end this procedure.
48
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
5.3 Windows NT4.0
1.
Move your courser as following sequence Start \ Settings \ Control Panel and
click Control Panel and double-click on the HSF Modem Region Select icon.
2.
Select your country form a list and click OK.
49
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
5.4 Windows 2000
1.
Move your courser as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Phone and Modem Options
icon.
2.
Select Dialing Rules and click My Location. Then click Edit….
50
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Click General and in the Country/region to select United States of America.
Then click Apply.
4.
Click OK.
51
D-Link DFM-562IS HSFi PCI Modem
5.
User’s Guide
Click OK to end this procedure.
52
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
5.5 Windows XP
1.
Move your courser as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Phone and Modem Options icon.
2.
Select Dialing Rules and click My Location. Then click Edit….
53
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Click General and in the Country/region to select United States of America.
Then click Apply.
4.
Click OK.
54
D-Link DFM-562IS HSFi PCI Modem
5.
User’s Guide
Click OK to end this procedure.
55
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
Chapter 6 Diagnostics
6.1 Windows 95/98/ME
1.
Move your cursor as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Modems icon.
2.
To test the modem by clicking on the Diagnostics tab. Select the COM port that
the modem is setting, and clicks More Info….
56
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Responding to AT commands and functioning correctly, it means that your
modem is working properly. Click OK to end this procedure.
4.
Click OK.
57
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
6.2 Windows 2000
1.
Move your cursor as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Phone and Modem Options
icon.
2.
Click on the Modems, then select D-Link DFM-562IS HSFi PCI Modem and
click Properties.
58
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Click Diagnostics. To test the modem by clicking Query Modem.
4.
If your modem is responding to AT commands and functioning correctly, it
means that your modem is working properly. Click OK to end this procedure.
59
D-Link DFM-562IS HSFi PCI Modem
5.
User’s Guide
Click OK to end this procedure.
60
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
6.3 Windows XP
1.
Move your cursor as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Phone and Modem Options
icon.
2.
Select Modems and click FM-56PCI-HSFi-AB, then click Properties.
61
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Click Diagnostics. To test the modem by clicking Query Modem.
4.
If your modem is responding to AT commands and functioning correctly, it
means that your modem is working properly. Click OK to end this procedure.
62
D-Link DFM-562IS HSFi PCI Modem
5.
User’s Guide
Click OK to end this procedure..
63
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
Chapter 7 Uninstalling Procedures
7.1 Windows 95
1.
Move your cursor as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Add/Remove Programs icon.
2.
Select D-Link DFM-562IS HSFi PCI Modem from the list and then click the
Add/Remove button.
64
D-Link DFM-562IS HSFi PCI Modem
3.
User’s Guide
Click Yes to remove the modem then click OK.
65
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
7.2 Windows 98/ME
1.
Move your cursor as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Add/Remove Programs icon.
2.
Select D-Link DFM-562IS HSFi PCI Modem from the list and then click the
Add/Remove button.
66
D-Link DFM-562IS HSFi PCI Modem
3.
User’s Guide
Click Yes to end this procedure and restart your computer.
67
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
7.3 Windows NT 4.0
1.
Move your cursor as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Add/Remove Programs icon.
2.
Select D-Link DFM-562IS HSFi PCI Modem from the list and then click
Add/Remove.
68
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
3.
Click Next.
4.
The message of The modem driver was un-installed successfully will appear,
and click Finish.
69
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
7.4 Windows 2000
1.
Move your cursor as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Add/Remove Programs icon.
2.
Click D-Link DFM-562IS HSFi PCI Modem. Then click Chang/Remove.
70
D-Link DFM-562IS HSFi PCI Modem
3.
User’s Guide
Click Close.
71
D-Link DFM-562IS HSFi PCI Modem
User’s Guide
7.5 Windows XP
1.
Move your cursor as following sequence Start \ Settings \ Control Panel and
click Control Panel. Then double-click on the Add or Remove Programs
icon.
2.
Click D-Link DFM-562IS HSFi PCI Modem. Then click Chang/Remove.
72
D-Link DFM-562IS HSFi PCI Modem
3.
User’s Guide
Click Close.
73