4-129-231-13 (1)
P/N7525000004E
Before operation
Digital Photo
Frame
Basic operations
Advanced operations
DPF-D82/D92
Using an external device
(with Bluetooth)
Using an external device
(with a computer)
Error messages
Troubleshooting
Operating Instructions
Before operating this unit, please read this manual thoroughly and
retain it for future reference.
Owner’s Record
The model and serial numbers are located at the rear.
Record the serial number in the space provided below. Refer to
these numbers whenever you call upon your Sony dealer
regarding this product.
Model No. DPF-D82/D92
Serial No. ________________________
© 2009 Sony Corporation
Additional information
WARNING
To reduce fire or shock hazard, do not
expose the unit to rain or moisture.
Do not expose the batteries to
excessive heat such as sunshine, fire
or the like.
CAUTION
Replace the battery with the specified
type only. Otherwise, fire or injury
may result. Dispose of used batteries
according to the instructions.
For the customers in the U.S.A.
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
If you have any questions about this product, you may
call:
Sony Customer Information Services Center
1-800-222-SONY (7669)
The number below is for the FCC related matters
only.
Regulatory Information
Declaration of Conformity
Trade Name:
Model No.:
Responsible Party:
Address:
SONY
DPF-D92
Sony Electronics Inc.
16530 Via Esprillo, San Diego,
CA 92127 U.S.A.
Telephone No.:
858-942-2230
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
2 GB
Declaration of Conformity
Trade Name:
Model No.:
Responsible Party:
Address:
SONY
DPF-D82
Sony Electronics Inc.
16530 Via Esprillo, San Diego,
CA 92127 U.S.A.
Telephone No.:
858-942-2230
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
For the State of California, USA
only
Perchlorate Material - special handling may apply,
See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains
perchlorate.
For the Customer in Europe
This product has been tested and found compliant
with the limits set out in the EMC Directive for using
connection cables shorter than 3 meters (9.8 feet).
Attention
The electromagnetic fields at the specific frequencies
may influence the picture of this digital photo frame.
Notice
If static electricity or electromagnetism causes data
transfer to discontinue midway (fail), restart the
application or disconnect and connect the
communication cable (USB, etc) again.
Disposal of Old Electrical &
Electronic Equipment (Applicable in
the European Union and other
European countries with separate
collection systems)
This symbol on the product
or on its packaging indicates
that this product shall not be
treated as household waste.
Instead it shall be handed
over to the applicable
collection point for the
recycling of electrical and
electronic equipment. By
ensuring this product is
disposed of correctly, you
will help prevent potential
negative consequences for
the environment and human health, which could
otherwise be caused by inappropriate waste handling
of this product. The recycling of materials will help to
conserve natural resources. For more detailed
information about recycling of this product, please
contact your local Civic Office, your household waste
disposal service or the shop where you purchased the
product.
Disposal of waste batteries
(applicable in the European Union
and other European countries with
separate collection systems)
This symbol on the battery or on the
packaging indicates that the battery
provided with this product shall not
be treated as household waste. By
ensuring these batteries are disposed
of correctly, you will help prevent
potentially negative consequences for
the environment and human health which could
otherwise be caused by inappropriate waste handling
of the battery. The recycling of the materials will help
to conserve natural resources. In case of products that
for safety, performance or data integrity reasons
require a permanent connection with an incorporated
battery, this battery should be replaced by qualified
service staff only. To ensure that the battery will be
treated properly, hand over the product at end-of-life
to the applicable collection point for the recycling of
electrical and electronic equipment. For all other
batteries, please view the section on how to remove
the battery from the product safely. Hand the battery
over to the applicable collection point for the
recycling of waste batteries.
For more detailed information about recycling of this
product or battery, please contact your local Civic
Office, your household waste disposal service or the
shop where you purchased the product.
Notice for the customers in the
countries applying EU Directives
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo, 1080075 Japan. The Authorized Representative for EMC
and product safety is Sony Deutschland GmbH,
Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to
the addresses given in separate service or guarantee
documents.
Continued
3 GB
Duplication, edition, or printing of a CD, TV
programs, copyrighted materials such as pictures or
publications, or any other materials except for your
own recording or creation is limited to private or
domestic use only. Unless you hold copyright or
have permission of copyright holders for the
materials to be duplicated, use of those materials
beyond this limit may infringe the provisions of the
copyright law and be subject to the copyright
holders claim for damages.
When using photo images with this digital photo
frame, pay special attention not to infringe the
provisions of the copyright law. Any unauthorized
use or modification of there’s portrait may also
infringe their rights.
For some demonstrations, performances, or
exhibits, photography may be forbidden.
Backup recommendations
To avoid potential risk of data loss caused by
accidental operation or malfunction of the digital
photo frame, we recommend that you save a
backup copy of your data.
Information
IN NO EVENT SHALL SELLER BE LIABLE
FOR ANY DIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY
NATURE, OR LOSSES OR EXPENSES
RESULTING FROM ANY DEFECTIVE
PRODUCT OR THE USE OF ANY PRODUCT.
Sony shall assume no responsibility for any
accidental or consequential damages or loss of the
recording contents which may be caused by use or
malfunction of the digital photo frame or memory
card.
On trademarks and copyrights
•
, Cyber-shot,
, “Memory
, “Memory Stick Duo”,
, “MagicGate Memory
Stick”, “Memory Stick PRO”,
, “Memory Stick PRO Duo”,
, “Memory Stick PRO-HG
Duo”,
, “Memory Stick
Micro”,
,
, “Memory StickROM”,
, “MagicGate”, and
are trademarks or registered
trademarks of Sony Corporation.
• Microsoft, Windows, and Windows Vista are
registered trademarks of Microsoft Corporation in
the United States and/or other countries.
• Macintosh and Mac OS are registered trademarks of
Apple Inc. in the United States and/or other
countries.
• CompactFlash is a trademark of SanDisk
Corporation in the U.S.A.
Stick”,
•
•
•
•
•
Notes on LCD screen
• Do not press against the LCD screen. The screen
may be discolored and that may cause a
malfunction.
• Exposing the LCD screen to direct sunlight for long
periods may cause malfunctions.
• The LCD screen is manufactured using extremely
high-precision technology, so over 99.99% of the
pixels are operational for effective use. However,
there may be some tiny black points and/or bright
points (white, red, blue or green in color) that
constantly appear on the LCD screen. These points
are normal in the manufacturing process and do not
affect the viewing in any way.
• Images may trail across on the LCD screen in a cold
location. This is not a malfunction.
4 GB
or xD-Picture Card™ is a trademark of
FUJIFILM Corporation.
The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Sony Corpration is under licence. Other
trademarks and trade names are those of their
resective owners.
Contains iTypeTM and fonts from Monotype
Imaging Inc.
iTypeTM is a trademark of Monotype Imaging Inc.
All other companies and product names mentioned
herein may be the trademarks or registered
trademarks of their respective companies.
Furthermore, “™” and “®” are not mentioned in
each case in this manual.
This unit is equipped with face recognition feature.
Sony Face Recognition technology developed by
Sony is used.
Notice for users
Program © 2009 Sony Corporation
Documentation © 2009 Sony Corporation
All rights reserved. This manual or the software
described herein, in whole or in part, may not be
reproduced, translated or reduced to any machine
readable form without prior written approval from
Sony Corporation.
IN NO EVENT SHALL SONY CORPORATION BE
LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES,
WHETHER BASED ON TORT, CONTACT, OR
OTHERWISE, ARISING OUT OF OR IN
CONNECTION WITH THIS MANUAL, THE
SOFTWARE OR OTHER INFORMATION
CONTAINED HEREIN OR THE USE THEREOF.
Sony Corporation reserves the right to make any
modification to this manual or the information
contained herein at any time without notice.
The software described herein may also be governed
by the terms of a separate user license agreement.
Any design data such as sample pictures provided in
this software cannot be modified or duplicated except
for the purpose of personal use. Any unauthorized
duplication of this software is prohibited under
copyright law.
Please note that unauthorized duplication or
modification of portraits or copyrighted work could
infringe the rights reserved by rights holders.
On the illustrations and screen
shots used in this manual
The illustrations and screen shots used in this
manual are of the DPF-D92 unless noted
otherwise.
The illustrations and screen shots used in this
manual may not be identical to those actually
used or displayed.
5 GB
Table of Contents
Before operation
Enjoying your photo frame in various
ways ...............................................8
Features ..........................................9
Checking included items ...............11
Identifying the parts .....................11
Basic operations
Preparing the remote control ........15
Setting the stand ..........................16
To display the photo frame on
the wall .........................................17
Connecting to the AC power
source ..........................................18
Turning the photo frame on ..........19
Setting the current time ................20
Inserting a memory card ..............21
Changing the display ....................23
Slideshow display .........................24
Clock and calendar display ...........25
Single view mode .........................26
Index image display ......................27
Advanced operations
Enjoying a slideshow ....................29
Changing the settings of
the slideshow ................................. 29
Refresh mode ...............................32
6 GB
Adding images to the internal
memory ........................................32
Exporting an image .......................34
Deleting an image .........................36
Registering a mark .......................37
Searching for an image
(Filtering) ......................................39
Specifying the playback device .....40
Adjusting the image size and
position ...................................40
Enlarging/reducing an image ..........40
Rotating an image ...........................41
Changing the settings of the auto
power on/off function ...................42
Using the alarm function ..............43
Setting the alarm ............................43
Setting the time to be alarmed ........44
Changing the settings ...................44
Setting procedure ...........................44
Items to set .....................................46
Displaying images on a USB
memory ........................................48
Using an external device
(with Bluetooth)
Transferring images using
Bluetooth.......................................49
Using an external device
(with a computer)
Connecting to a computer ............51
System requirements ......................51
Connecting to a computer to exchange
images ...........................................51
Disconnecting your computer ........52
Error messages
If an error message appears .........53
Troubleshooting
If trouble occurs ...........................55
Additional information
Precautions ..................................60
Safety .............................................60
Installation .....................................60
Cleaning .........................................60
Restrictions on duplication .............61
Disposing of the photo frame ..........61
About memory cards ....................61
“Memory Stick” ..............................61
SD memory card ............................62
xD-Picture Card .............................62
CompactFlash card ........................62
Notes on using a memory card .......63
Specifications ...............................64
Index ............................................66
7 GB
Before operation
Enjoying your photo frame in various ways
The Sony DPF-D82/D92 is a digital photo frame for easily displaying images taken with a digital
camera or other device, without using a computer.
8 GB
Features
Before operation
x Support for various memory cards*
Supports various memory cards and other
devices, such as a “Memory Stick”,
CompactFlash card, SD memory card, xDPicture Card, and USB memory. Just insert a
memory card removed from a digital camera
or other device, and you will be able to view
the images immediately. (.page 21, 48)
x Various modes
The displayed image can be switched
automatically as though you are turning the
pages of an album yourself. You can select
from various modes, including just images, a
clock, or calendar view. You can also change
playback settings such as the playback order.
(.page 29)
x Adding images to internal memory
The images you add to the album are saved
in internal memory. (.page 32)
x Various display functions
You can enjoy various viewing modes, such
as the slideshow display, Clock and calendar
display, Single view mode, and Index image
display. (.page 23)
x Exporting images
You can export images in the album to your
memory card. (.page 34)
Continued
9 GB
x Search function
You can search for images by the date,
folder, image direction, and mark.
(.page 39)
x Alarm function
The photo frame announces the specified
time on the image and using sound.
(.page 43)
x Automatic rotation of images
The photo frame automatically rotates
images to their proper orientation. Images
are also automatically rotated when the
photo frame is set in either the portrait or
landscape position. (.page 16)
x Easy transfer of images taken with a
Bluetooth compatible mobile phone
or other device*
You can transfer images to the photo frame's
internal memory from a Bluetooth
compatible device via a Bluetooth adaptor
(optional). (.page 49)
x Displaying images on a wall
You can hang the photo frame on the wall.
(.page 17)
* We do not guarantee proper operations for all types
of devices.
10 GB
Checking included
items
For details, see the pages indicated in the
parentheses.
The illustrations are of the DPF-D92. The
locations and names of buttons and connectors
of the DPF-D82 are identical to those of the
DPF-D92, although the LCD screen size and
shape is different.
Front
A LCD screen
B Remote sensor
When using the supplied remote control, point
it at this sensor.
Continued
11 GB
Before operation
Make sure that the following items are
included.
• Digital photo frame (1)
• Stand (1)
• Remote control (1)
• AC adaptor (1)
• Operating Instructions (this manual) (1)
• Read This First (1)
• Warranty (1)
(In some regions, the warranty is not
supplied.)
Identifying the parts
D:\DPF series\V Series\4129231131\4129231131\4129231131DPFD92CED\01GB-DPFD92CED\030C01.fm
Master: Left
030C01.fm Page 12 Wednesday, April 8, 2009 8:58 AM
Rear
A Connector for USB A/Bluetooth
adaptor (.page 49)
Connect a Bluetooth adaptor (optional:
DPPA-BT1) when you want to transfer
images wirelessly from a BLUETOOTH
compatible mobile phone or digital camera.
You can also connect a USB memory
compatible with USB mass storage.
B
USB B connector (.page 51)
Connect a USB cable when you want to use
the photo frame with a computer.
C Stand (.page 16)
D DC IN 12 V jack (.page 18)
Insert the plug of the supplied AC adaptor to
this jack, and connect to the wall outlet.
E Power Switch (.page 19)
F “Memory Stick PRO” (Standard/
Duo) slot (.page 21)
G Access lamp
H Standby indicator
I 1 (on/standby) button
J MENU button
Displays the menu.
From the menu, you can operate the same
functions as those of the buttons on the
remote control, such as [Slideshow Settings],
[Rotate], [Add to album] and [Date/time
settings].
K Direction (B/b/v/V) buttons,
Press B/b/v/V to select the menu items. Then
press
to enter the selection.
L BACK button
Returns to the previous screen.
M Reset switch (.page 58)
The date/time setting, alarm settings, and the
auto power on/off settings return to their
factory default setting. Use a long, thin object,
such as a pin, to push the switch.
N CompactFlash card/Microdrive
slot (.page 21)
O SD memory card/MMC/xD-Picture
Card slot (.page 21)
12 GB
DPF-D82/D92 4-129-231-13 (1)
Before operation
P
Q
R
S
Buzzer
VIEW MODE button (.page 23)
Alarm switch (.page 43)
Holes for hanging unit on the wall
(.page 17)
T Space for storing the stand
Continued
13 GB
Remote control
14 GB
A VIEW MODE button (.page 23)
B SLIDE-SHOW ( ) button
(.page 23)
C INDEX ( ) button (.page 23)
D SINGLE (
) button
(.page 23)
E MENU button
F BACK button
G 1 (on/standby) button
H CLOCK ( ) button (.page 23)
I Zoom in ( )/Zoom out ( ) buttons
(.page 40)
J ALBUM ( ) button (.page 32)
K Direction (B/b/v/V) buttons
L
(enter) button
M ROTATE (
) button
(.page 40)
Basic operations
Preparing the remote
control
The supplied lithium battery (CR2025) has
already been inserted into the remote control.
Pull out the protective sheet before use as
shown in the figure.
Replacing the battery of the
remote control
If the remote control stops working, replace the
battery (CR2025 lithium battery) with a new
one.
1
Pull out the battery holder.
While pressing in the tab of the battery
holder, pull out the battery holder.
Basic operations
Protective sheet
Using the remote control
Point the top end of the remote control towards
the remote sensor on the photo frame.
2
Remove the old battery from the
battery holder and then insert a new
battery.
Insert the battery so that “+” is facing
upwards.
Remote
sensor
3
Reinsert the battery holder into the
remote control.
WARNING
Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
Notes
Note
The photo frame may fall if you use the buttons on the
photo frame when it is hanging on the wall. Operate
the photo frame using the remote control.
• When the lithium battery becomes weak, the
operating distance of the Remote control may
shorten, or the Remote control may not function
properly. In this case, replace the battery with a
Sony CR2025 lithium battery. Use of another
battery may present a risk of fire or explosion.
Continued
15 GB
• Using a battery other than the specified one may
result in the battery rupturing.
• Dispose of used batteries as specified by the local
authorities.
• Do not leave the remote control in a very hot and
humid place.
• Take care that no foreign objects get inside the
remote control when you, for example, replace the
battery.
• Incorrect use of the battery may cause leaking and
corrosion.
Setting the stand
1
Hold the photo frame tightly and
insert the stand straight into the
screw hole on the rear panel.
– Do not recharge the battery.
– When the remote control will not be used for a
long period of time, remove the battery from the
remote control to prevent leaking and corrosion.
– Incorrectly inserting, shorting, dismantling, or
heating the battery, or throwing it into a fire
may cause the battery to rupture or leak.
About descriptions in this
manual
2
Screw the stand into the screw hole
firmly until the stand stops turning.
The operations described in this manual are
based on remote control operation. When an
operation is performed differently, for example,
with the remote control and the buttons on the
photo frame, it will be explained in a tip.
Setting to portrait or landscape
orientation
You can set the photo frame to portrait or
landscape orientation by rotating it without
moving the stand.
16 GB
When the photo frame is placed in the portrait
orientation, the image is also automatically
rotated to its proper orientation.
The directions indicated on the direction button
on the rear panel depend on the orientation of
the photo frame.
To display the photo
frame on the wall
You can hang the photo frame on the wall
using the following procedure.
1
Prepare screws (not supplied)
suitable for the screw holes on the
rear panel.
More than 25mm (1 inch)
4.2mm
(3/16 inch)
Notes
• Check whether the stand is stable. If the stand is not
set properly, the photo frame may fall over.
• When the photo frame is placed in the portrait
orientation, the Sony logo doesn't light up.
• The photo frame does not detect and rotate the
orientation of images when [Auto display
orientation] of [General Settings] on the
(Settings) tab is set to [OFF].
• A magnet is contained in the storage portion of the
stand. Do not keep anything that is easily affected
by magnetism, such as a cash card or credit card,
near the photo frame. If you place the photo frame
near a CRT-based television, the color of the TV’s
display may be changed.
8.6mm
(11/32 inch)
Holes for hanging
the unit on the wall
2
Screw the screws (not supplied) into
the wall.
Be sure the screws (not supplied) protrude
between 2.5 to 3mm (1/8 inch) from the
surface of the wall.
Tip
It is easier to turn the stand if you wind or wrap a
rubber band tightly around the stand when you
remove the stand from the photo frame.
Between
2.5mm to 3mm
(1/8 inch)
3
Hang the photo frame on the wall by
fitting the hole on the rear panel to
the screws on the wall.
Notes
• Use screws suitable for the quality of the material of
the wall. The screws may be damaged, depending
on the type of material used in the wall. Set the
screws in a pillar or stud in the wall.
Continued
17 GB
Basic operations
4mm (3/16 inch)
• When you want to re-insert the memory card,
remove the photo frame from the wall, then eject
and re-insert the memory card while the photo
frame is placed on a stable surface.
• Store the stand in the place provided when you hang
the photo frame on the wall.
• Connect the plug of the supplied AC adaptor to the
photo frame and set the power switch to ON. And
then connect the AC adaptor to the wall outlet after
hanging the photo frame on the wall.
• We take no responsibility for any accidents or
damage caused by defects of attachment, misuse, or
natural disasters, etc.
Connecting to the AC
power source
1
2
Insert the plug of the AC adaptor
into the DC IN 12 V jack on the rear
of the photo frame.
Connect the AC adaptor to the wall
outlet.
To the DC IN 12 V jack
To wall outlet
AC adaptor
Notes
• The socket outlet should be as close as possible to
the unit, and easily accessible.
• Do not place the photo frame in an unsteady
location such as on an unsteady table or tilted
surface.
• Connect the AC adaptor to an easily accessible wall
outlet close by. If trouble occurs while using the
adaptor, immediately shut off the power by
disconnecting the plug from the wall outlet.
• Do not short the plug of the AC adaptor with a
metal object. Doing so may cause a malfunction.
• Do not use the AC Adaptor placed in a narrow
space, such as between a wall and furniture.
18 GB
• Insert the plug of the AC adaptor firmly, if the
connection is loose, the photo frame may turn off
when it is moved.
• After use, remove the AC adaptor from the
DC IN 12 V jack of the photo frame, and remove
the AC adaptor from the outlet.
• Even if your photo frame is turned off, AC power
(house current) is still supplied to it while connected
to the wall outlet via the AC adaptor.
• Do not turn the photo frame off or disconnect the
AC adaptor from the photo frame before the
standby indicator turns red. Doing so may damage
the photo frame.
Turning the photo frame
on
When the power switch is set to
off
When the power switch is set to on, the standby
indicator turns green and the Sony logo on the
front panel lights up.
Basic operations
When the power switch is set to
on
Press 1 (on/standby) on the photo frame or
remote control to turn on the power. The
standby indicator turns to green from red. The
Sony logo on the front panel lights up.
Continued
19 GB
Turning off the power
Hold 1 (on/standby) on the photo frame or
remote control until the power turns off. The
standby indicator turns to red from green.
Note
Do not turn the photo frame off or disconnect the AC
adaptor from the photo frame before the standby
indicator turns red. Doing so may damage the photo
frame.
Operations in an initial state
Setting the current time
The clock of the photo frame needs to be
adjusted in order to display an accurate time in
the clock and calendar view modes.
1
Press MENU.
The menu screen is displayed.
2
When the photo frame is turned on without a
memory card connected, the initial display
below appears on the screen.
Press B/b to select the
(Settings) tab.
The settings screen is displayed.
Tip
You can use the B/b button only when a
memory card is inserted in the photo frame, an
external device is connected, or anything other
than the clock and calender settings item
(page 25) are selected.
3
Press v/V to select [Date/time
settings] and then press
.
The Date/time settings screen is displayed.
If the photo frame is not operated for 10
seconds, the demo mode is displayed. If any
other button than the power button is pressed,
the screen returns to the initial display.
First, press MENU during the initial display,
and then set the date and time.
4
Adjust the date.
1 Press v/V to select [Date] and then
press
.
2 Press B/b to select month, day, and
year, and then press v/V to select a
value, then press
.
5
Adjust the time.
1 Press v/V to select [Time] and then
press
.
2 Press B/b to select hour, minute, and
second, and then press v/V to select a
value, then press
.
20 GB
6
Select the format of the date.
1 Press v/V to select [Date Display Order]
.
and then press
2 Press v/V to select a format and then
.
press
• Y-M-D
• M-D-Y
• D-M-Y
7
Set the day to start the week for the
calendar.
8
Insert the memory card firmly into the
corresponding slot with its label side
facing toward you (when you are facing
the back side of the photo frame).
The access lamp flashes when the memory card
is inserted correctly. Reinsert the memory card
after checking the label side of the memory
card if the access lamp does not flash.
For details on the memory cards you can use
with this photo frame, see pages 61 to 63.
Access lamp
Select the time display.
1 Press v/V to select [12hr/24hr display]
and then press
.
2 Press v/V to select [12 hours] or
[24 hours] and then press
9
.
Press MENU.
The menu screen is closed.
Insert the memory card firmly into the
corresponding slot with its label side facing
toward you. The slot order from the top is
“Memory Stick” (“Memory Stick Duo”),
CompactFlash card, SD memory card and xDPicture Card.
Continued
21 GB
Basic operations
You can set the day that appears on the
very left when the calendar is displayed.
1 Press v/V to select [First Weekday] and
then press
.
2 Press v/V to select [Sunday] or
[Monday] and then press
.
Inserting a memory card
To remove a memory card
Remove the memory card from its slot in the
opposite direction from which it was inserted.
Notes
• When inserting the memory card, it will only insert
part of the way, so do not try to force it as this could
damage the memory card and/or photo frame.
• This photo frame has a slot that is both a “Memory
Stick” standard and Duo size compatible slot, so
you do not need a “Memory Stick” adaptor.
• The SD memory card/xD-Picture Card dualpurpose slot automatically detects the card type.
• Before using a memory card, see “About memory
cards” on page 61.
Display priority of images
If a memory card is inserted or an external device is
connected, the images of the inserted memory card or
connected device are displayed automatically.
To manually change the memory card or external
device to be displayed, specify it in
(Select
device) menu (page 40).
The photo frame displays the images of the
memory card in the following priorities.
• Memory card / The device connected to the USB
A/Bluetooth connector t internal memory
• If multiple memory cards are inserted when the
photo frame is turned on, the images of the first
memory card you inserted take priority and are
displayed.
• If multiple devices are inserted while the photo
frame is turned off, and then the photo frame is
turned on, the images of the device displayed when
the photo frame is turned off take the first priority
and are displayed. A device connected to the USB
A/Bluetooth connector, however, may not be able to
take priority.
• If a memory card is replaced while the photo
frame is turned off, and then the photo frame is
turned on, the images are displayed in the
following priorities:
“Memory Stick” b CompactFlash card
b SD memory card b xD-Picture Card b the device
connected to the USB A/Bluetooth connector b
internal memory
• If no memory card is inserted and no device is
connected, the images saved in the album in the
internal memory are displayed.
22 GB
Notes
• Due to one of the characteristics of the internal
memory device, images stored for long time or read
many times may be subject to data error when read
too often.
• For the file formats that the photo frame can
display, see page 64.
Changing the display
1
Press VIEW MODE.
The view mode screen is displayed.
3
Press B/b/v/V or VIEW MODE to
select the style you want and then
press
.
2
Select the group you want.
Group
Slideshow
Explanation
Displays a slideshow display
style.
Displays a clock or calendar
style.
Clock and
calendar
Displays a single image
style.
Index
Displays a thumbnail list
style.
Tip
Select the group you want using B/b after
moving the cursor to the group area using B/b/
v/V, when you operate the photo frame using
the buttons on the photo frame.
23 GB
Basic operations
Note
If you have not operated the photo frame for an
extended period of time, the style the cursor is on will
be selected automatically.
Slideshow display
Group
Slideshow
Image
Style
Explanation
A
Single view
Displays one image after another.
B
Multi image view
Displays multiple images at the same time.
C
Clock view
Displays images with the present date and time.
D
Calendar view
Displays images, one after another, while
showing a calendar. The present date and time
is displayed.
E
Time Machine
Displays images with the shooting date and
time. The present date and time cannot be
displayed.
F
Random view
Displays images while randomly switching
between a number of different slideshow styles
and effects.
A
B
E
F
Tips
• If the power is on, and no memory card is inserted,
and no device is connected, the images stored in
internal memory are displayed. If no images are
saved in internal memory, demonstration mode
starts automatically. Demonstration mode ends if a
button other than 1 (on/standby) is pressed.
• For details on the playback order in a slideshow
display, see page 46.
24 GB
C
D
• You can set the interval, effect, listing order, or
color effect when you select the slideshow display.
Refer to “Slideshow Settings” (page 31).
• You can select the single view mode when you
press
on the photo frame when the image you
want appears in the slideshow display.
• You can use the VIEW MODE button on the photo
frame.
Clock and calendar display
Clock2
Clock3
Clock4
Clock5
Clock6
Clock7
Clock8
Clock9
Clock10
Calendar2
Calendar3
Clock11
Calendar1
Lunar Calendar
Arabic Calendar
Farsi Calendar
(when you select
(when you select
(when you select
[Simplified
[Arabic] in
[Persian] in
Chinese] in
[Language setting]) [Language setting])
[Language setting])
Note
You can select only the
(Settings) tab when the
Clock and calendar display is displayed.
Tip
You can use the VIEW MODE button on the photo
frame.
25 GB
Basic operations
Clock1
Single view mode
Group
A
Image
Style
Explanation
A
Entire image
Displays an entire image in the screen. You can
switch the images to be displayed by pressing
B/b.
B
Fit to screen
Displays an image over the whole screen. You
can switch the images to be displayed by
pressing B/b.
C
Entire image (with
Exif)
Displays image information, such as the image
number, file name, and shooting date while
displaying the entire image. You can switch the
images to be displayed by pressing B/b.
Refer to “About the information display”
(page 28) for details on the image information.
D
Fit to screen (with
Exif)
Displays image information, such as the image
number, file name, and shooting date in fit to
screen mode. You can switch the images to be
displayed by pressing B/b.
Refer to “About the information display”
(page 28) for details on the image information.
B
Tips
• If the power is on, and no memory card is inserted,
and no device is connected, the images stored in
internal memory are displayed. If no images are
saved in internal memory, demonstration mode
starts automatically. Demonstration mode ends if a
button other than 1 (on/standby) is pressed.
• You can set the image display mode by pressing
VIEW MODE and pressing B/b to select either
entire image or fit to screen mode. Not all images
are able to use the fit to screen mode.
• You can use the VIEW MODE button on the photo
frame.
26 GB
C
D
Index image display
Group
Style
Explanation
A
Index 1
Displays a list of large thumbnails. You can
select an image by pressing B/b/v/V.
B
Index 2
Displays a list of thumbnails. You can select an
image by pressing B/b/v/V.
C
Index 3
Displays a list of small thumbnails. You can
select an image by pressing B/b/v/V.
Index
A
B
C
Tips
• A thumbnail is a small-sized image for index use
that is recorded in the pictures taken by a digital
camera.
• If the power is on, and no memory card is inserted,
and no device is connected, the images in internal
memory are displayed. If no images are saved in
internal memory, demonstration mode starts
automatically. Demonstration mode ends if a button
other than 1 (on/standby) is pressed.
• You can select the single view mode when you
press
on the photo frame when the image you
want appears in the index image display.
• You can use the VIEW MODE button on the photo
frame.
Continued
27 GB
Basic operations
Image
About the information display
4 Setting information
Icons
Meaning
Protect indication
Associated file indication
(Displayed when there is an
associated file such as a motion
file or a miniature e-mail image
file.)
Displays when you have
registered a mark.
The following information is displayed.
1 Display type
– Entire image
– Fit to screen
– Entire image (with Exif)
– Fit to screen (with Exif)
2 Ordinal number of the displayed image/Total
number of images
Input media indication for the displayed
image is shown as follows:.
Icons
Meaning
“Memory Stick” input
SD Memory Card input
CompactFlash input
xD-Picture Card input
External Device input
Internal memory input
3 Image details
– File format (JPEG(4:4:4), JPEG(4:2:2),
JPEG(4:2:0), RAW)
– Number of pixels (width × height)
– Manufacturer name of image input device
– Model name of image input device
– Shutter speed (e.g.: 1/8)
– Aperture value (e.g.: F2.8)
– Exposure value (e.g.: +0.0EV)
– Rotation information
28 GB
5 Image number (folder-file number)
This is displayed if the image is DCF
compliant.
If the image does not comply with DCF, up
to 10 characters of its file name are
displayed.
6 Shooting date/time
Advanced operations
Enjoying a slideshow
You can display images stored in the internal
memory or on a memory card, one after
another, automatically.
When you turn on the photo frame, the
slideshow plays continuously from the
previous play.
1
Press VIEW MODE.
Changing the settings of the
slideshow
1
The menu is displayed.
2
Select
Press B/b to select the
(Settings) tab.
The settings screen is displayed.
3
The view mode screen is displayed.
2
Press MENU.
Press v/V to select [Slideshow
Settings] and then press
.
The slideshow settings screen is
displayed.
(slideshow).
Advanced operations
Tip
Select
(slideshow) using B/b after moving
the cursor to the group area using B/b/v/V
when you operate the photo frame using the
buttons on the photo frame.
4
Press v/V to select the item and
then press
.
Refer to the tables on the next page for
details on the setting items.
3
Press B/b/v/V to select the style you
want, then press
.
Notes
• Note the following when you select a slideshow
using the image stored on the memory card.
– Due to one of the characteristics of the memory
card devices, images may be subject to data
error when read too often.
– Do not run a slideshow for a long time with a
small number images. This may cause data
error.
Refer to “Slideshow display” (page 24)
for details on the slideshow styles.
– We recommend you back up images on the
memory card often.
• When the photo frame is, for instance, displaying a
slideshow, changes to the settings of some items are
unavailable. These items are displayed in gray and
cannot be selected.
• The slideshow starts from the first image if you set
the power switch to OFF before entering the
standby mode, if you reset the photo frame.
Continued
29 GB
• When the screen is too bright, it may make you feel
nauseous. Be careful that you do not make the
brightness settings too bright when you use the
photo frame.
Tip
You can also use the VIEW MODE button on the
photo frame.
30 GB
*: Factory default settings
Item
Setting
Description
Slideshow
Settings
Interval
Set a value from 3 sec., 7 sec.*, 20 sec., 1 min., 5 min., 30 min., 1 hour,
3 hours, 12 hours, 24 hours for the interval between images.
Note
An image may not switch at the intervals you set on the menu, depending
on the style of the slideshow, color effect, or image size.
Effect
Color effect
Display Mode
Transitions to the next image as though the previous
image is being pushed from the center to the four
corners.
Vert. blinds
Transitions to the next image as though blinds are
being lowered vertically.
Horiz. blinds
Transitions to the next image as though blinds are
being pulled horizontally.
Fade*
Transitions to the next image by fading out the current
image and fading in the next image.
Wipe
Transitions to the next image as though the current
image is being wiped off the screen to reveal the next
image.
Random
Uses the above five effects randomly.
ON
Displays images randomly.
OFF*
Displays images according to the [Listing Order]
setting of [General Settings].
Color*
Displays an image in color.
Sepia
Displays an image in a sepia color.
Monochrome
Displays an image in monochrome.
Select the desired display size from the following:
Note
The original image data will not change.
Entire image*
Displays an entire image enlarged to proper size. (An
image may be displayed with margins on the top,
bottom, left and right.)
Fit to screen
Zooms in at the center of the image enough to fill the
whole screen.
Note
An image may not display with the display size you set
on the menu, depending on the style of the slideshow.
31 GB
Advanced operations
Shuffle
Center cross
Refresh mode
Due to one of the characteristics of the device,
images stored for a long time or read many
times may be subject to data error when read
too often.
This photo frame refreshes the internal memory
automatically to prevent these errors,
depending on the status of the internal memory.
The confirmation screen used for refreshing the
internal memory is displayed automatically
when the refresh is needed.
The refresh starts when you select [OK]. The
Refresh also starts automatically when no
operation is attempted for 30 seconds. If you
select [Cancel], the confirmation screen used
for refreshing the internal memory is displayed
the next time.
Adding images to the
internal memory
You can use the photo frame as a digital album,
saving important images in the internal
memory.
Tip
In [Image file size] of the menu, you can preset
whether to optimize the size of images or save images
as is, without compressing them, when you save them
to the internal memory (page 46).
When [Image file size] is set to [Album], up to
approx. 2,000 images can be added to the album.
When set to [Original], the number of images that can
be saved may vary, depending on the original image
file size.
1
Press
(Album) when an image
stored on the memory card or the
external device is displayed on the
screen.
Tip
Select [Add to album] using v/V after pressing
the MENU button and then select
(Editing) using B/b.
Do not turn the photo frame to OFF while the
internal memory is being refreshed. It may
cause a malfunction.
It may take approximately 5 minutes to refresh
the internal memory.
Notes
• We recommend that you perform a backup of your
data periodically to avoid losing it.
• Do not run a slideshow with less than 10 images
continuously if you have set the interval time for the
slideshow to 3 seconds. You may not be able to
protect some images in the internal memory.
32 GB
Single image display
1 Press B/b/v/V to select the image to
Slideshow display
add to the album and then press
.A
check mark will be attached to the
check box of each selected image.
Repeat this operation to add multiple
images at the same time.
Index image display
Press v/V to select [Add this image],
[Selected images] or [Add all
images] and then press
.
4
If you select [Add this image], the image
currently displayed is added to the album.
Go to step 4. (This item cannot be selected
on the slideshow display.)
If you select [Selected images], you can
select the image you want to add from the
image list. Go to step 3.
If you select [Add all images], the image
list is displayed. A check mark is attached
to the check box of all the images. Go to
step 4.
3
The confirmation screen used to decide
whether to add an image or not to the
internal memory is displayed.
Specify the image to add from the
image list.
About the image list
During a search: Displays all the images
applicable to the criteria used for the
search.
Other than during a search: Displays all
images in the device displayed on the
screen.
Refer to “Searching for an image
(Filtering)” (page 39).
Press v/V to select the folder you
want and press
.
Tip
A new folder is created automatically when you
select [New folder].
5
Press v/V to select [Yes] and then
press
.
The image is saved in the specified folder
in internal memory.
Continued
33 GB
Advanced operations
2
To cancel the selection, select images to
cancel and then press
to delete the
check mark in the check box.
2 Press MENU.
The confirmation screen used for
selecting a folder is displayed.
6
Press
when the confirmation
screen is displayed.
Exporting an image
Notes
• Images in the internal memory cannot be added to
the album.
• Do not turn off the power, remove the memory card,
or disconnect the external device while an image is
being added. Doing so may damage the photo frame
or memory card, or damage the data.
You can export the images in the internal
memory to a memory card or external device.
1
The menu is displayed.
Tips
• To perform this operation using the remote control,
press the MENU button on the remote control and
then press v/V to select [Add to album] from
(Editing) and then press
.
• You can also use the MENU button on the photo
frame.
• You can change the thumbnail size using [ / ] in
the image list.
• Due to one of the characteristics of the internal
memory device, images stored for long time or read
many times may be subject to data error when read
too often. We recommend that you perform a
backup of your data periodically to avoid losing it.
Press MENU when an image stored
on the internal device is displayed
on the screen.
2
Press B/b to select the
tab.
(Editing)
The screen used for editing is displayed.
3
Press v/V to select [Export] and
then press
.
The Export menu is displayed.
Single image display
4
Press v/V to select [Export this
image], [Selected images] or [Export
all images] and then press
.
If you select [Export this image], the
image currently displayed is exported to
the device. Go to step 6. (This item cannot
be selected on the slideshow display.)
If you select [Selected images], you can
select the image you want to export from
the image list. Go to step 5.
If you select [Export all images], the
image list is displayed. A check mark is
attached to the check box of all the
images. Go to step 6.
34 GB
5
Specify the image to export from the
image list.
7
About the image list
During a search: Displays all the images
applicable to the criteria used for the
search.
Other than during a search: Displays the
image list of the album on the screen.
6
Press v/V to select the device to
which to export the image and then
press
.
The confirmation screen used to decide
whether to export or not is displayed.
Tip
A new folder is created automatically when you
select [New folder].
8
Press v/V to select [Yes] and then
press
.
The exporting is finished.
9
Press
when the confirmation
screen is displayed.
The image is copied to the specified
device.
Note
Do not turn off the power, remove the memory card,
or disconnect the external device during exporting.
Doing so may damage the photo frame or memory
card, or damage the data.
Tips
• You can also use the MENU button on the photo
frame.
• You can enlarge or reduce the image to export when
you select the index image display.
• Any device that is not recognized by the photo
frame is displayed in gray and you cannot select it.
35 GB
Advanced operations
Refer to “Searching for an image
(Filtering)” (page 39).
1 Press B/b/v/V to select the image you
want to export and then press
.A
check mark will be attached to the
check box of each selected image.
Repeat this operation to export multiple
images at the same time.
To cancel the selection, select images to
cancel and then press
to delete the
check mark in the check box.
2 Press MENU.
The screen used for selecting the device
to which to export is displayed.
Press v/V to select the folder you
want to save to and press
.
To cancel the selection, select images to
cancel and then press
to delete the
check mark in the check box.
2 Press MENU.
The delete confirmation screen is
displayed.
Deleting an image
1
Press MENU when an image is
displayed on the screen.
The menu is displayed.
2
Press B/b to select the
tab.
6
(Editing)
The screen used for editing is displayed.
3
4
If you select [Delete this image], the
image currently displayed is deleted. Go
to step 6. (This item cannot be selected on
the slideshow display.)
If you select [Selected images], you can
select the image you want to delete from
the image list. Go to step 5.
If you select [Delete all images], the
image list is displayed. A check mark is
attached to the check box of all the
images. Go to step 6.
5
The image is deleted.
7
Press v/V to select [Delete] and
then press
.
Press v/V to select [Delete this
image], [Selected images] or [Delete
all images] and then press
.
Specify the image to delete from the
image list.
About the image list
During a search: Displays all the images
applicable to the criteria used for the
search.
Other than during a search: Displays all
images in the device displayed on the
screen.
Refer to “Searching for an image
(Filtering)” (page 39).
1 Press B/b/v/V to select the image to
delete and then press
. A check mark
will be attached to the check box of
each selected image.
Repeat this operation to delete multiple
images at the same time.
36 GB
Press v/V to select [Yes] and then
press
.
Press
when the confirmation
screen is displayed.
To format the internal memory
1
Press MENU.
The menu is displayed.
2
Press B/b to select the
(Settings) tab.
The settings screen is displayed.
3
Press v/V to select [Initialize] and then
press .
4
Press v/V to select [Format internal
memory] and then press .
The confirmation screen used for
initializing the internal memory is
displayed.
5
Press v/V to select [Yes], then press
.
Notes
• When the message [Cannot delete a protected
image.] appears on the screen, the image file was set
to Read Only on a computer. In this case, connect
the photo frame to a computer, and delete this file
using the computer.
• The total capacity of the internal memory is not
equal to the remaining capacity, even immediately
after initialization.
• If deletion has started, the deleted image cannot be
recovered even if you stop deletion. Delete images
only after confirming you actually want to delete
them.
Tips
• You can also use the MENU button on the photo
frame.
• You can enlarge or reduce the image when you
select the index image display.
Registering a mark
You can produce a slideshow only with images
which have been selected beforehand and have
been marked. You can easily check for images
with marks using the index image display or
single view mode.
1
Press MENU when an image is
displayed on the screen.
The menu is displayed.
2
Press B/b to select the
tab.
(Editing)
3
4
5
Press v/V to select [Marking] and
then press
.
Press v/V to select the mark you
want and then press
.
Press v/V to select [Mark this
image], [Selected images] or [Mark
all images] and then press
.
If you select [Mark this image], the image
currently displayed will be marked and
showed in the future. Go to step 7. (This
item cannot be selected on the slideshow
display.)
If you select [Selected images], you can
select the image to which you want to
attach a mark from the image list. Go to
step 6.
If you select [Mark all images], the image
list is displayed. A check mark is attached
Continued
37 GB
Advanced operations
The screen used for editing is displayed.
to the check box of all the images. Go to
step 7.
6
Specify the image to which you want
to attach a mark from the image list.
About the image list
During a search: Displays all the images
applicable to the criteria used for the
search.
Other than during a search: Displays all
images in the device.
Refer to “Searching for an image
(Filtering)” (page 39).
1 Press B/b/v/V to select the image to
which to attach and then press . A
check mark will be attached to the
image. Repeat this operation to attach a
mark to multiple images at the same
time.
To cancel the selection, select an
imeges you want to cancel and then
press
to remove the check mark
from the check box.
2 A mark will be attached to the image
for which a check mark has been placed
in the check box.
If a check mark is removed from the
check box of an image, the mark will be
removed from the image.
7
Press v/V to select [Yes] and then
press
.
The mark is attached to the selected
image.
To delete the registration of a
mark
Select [Unmark this image] or [Unmark all
images] and then press
in step 5. You can
also cancel the selection when you remove the
check mark from the check box.
[Unmark this image]: Removes a mark from
the image currently displayed. (This item
cannot be selected on the slideshow display.)
38 GB
[Unmark all images]
During a search: Removes a marks from all the
images applicable to the criteria specified in the
search.
Other than during a search: Removes all marks
from all images stored on the device displayed.
Note
A mark is saved only when it is registered with an
image in the internal memory. A mark registered with
an image on a memory card or an external device is
removed when the power is turned off, or if you
change the device being displayed.
Tips
• You can select a mark from among 3 types.
• You can also use the MENU button on the photo
frame.
• You can enlarge or reduce the image when you
select the index image display.
Searching for an image
(Filtering)
You can search for an image which is stored in
internal memory or on a memory card. You can
filter an image using various criteria, such as
the date, the folder in which the image is saved,
the orientation of the image or mark, etc.
1
Press MENU when an image is
displayed on the screen.
The menu is displayed.
Press B/b to select the
tab.
(Editing)
The screen used for editing is displayed.
Press the MENU button when an image is
displayed on the screen and then select [Exit
search (show all photo)].
To change the criteria for a
search
Press the BACK button when an image you
searched for is displayed on the screen.
Notes
• Do not turn off the power, remove the memory card,
or disconnect the external device during a
searching. Doing so may damage the photo frame or
memory card, or damage the data.
• The search is cancelled automatically in the
following cases.
– When you change the playback device
Note
3
4
You cannot select the
(Editing) tab when
the clock and calendar are displayed.
– When you search for an image which is stored
on a memory card or external device and then
remove that memory card or external device
Press v/V to select [Search] and
then press
.
Tip
Press v/V to select the criteria you
want and then press
.
You can also use the MENU button on the photo
frame.
• [Search by date]: Filters by the date.
• [Search by folder]: Filters by the folder.
• [Search by vertical/horizontal]: Filters
by the image orientation.
• [Search by mark]: Filters by the mark.
5
Press v/V to select the item you
want and then press
.
39 GB
Advanced operations
2
To cancel the search for an
image
Specifying the playback
device
You can specify the memory card or external
device to be displayed.
1
Press B/b to select the
device) tab.
1
(Select
The screen used for selecting a device is
displayed.
Tip
Insert the device at this point during the
procedure if the device you want to use cannot
be selected.
3
Enlarging/reducing an image
You can enlarge or reduce an image in single
view mode.
Press MENU.
The menu is displayed.
2
Adjusting the image size
and position
Press v/V to select the device you
want to display and then press
.
The images of the selected device are
displayed.
Tips
• You can also use the MENU button on the photo
frame.
• The search is cancelled automatically when you
change the playback device during a search.
To enlarge an image, press
(zoom in) on the remote control. To
reduce an enlarged image, press
(zoom out).
Each press of the button enlarges the
image further. You can enlarge an image
to a maximum of 5 times the original
scale. You can move an enlarged image
up, down, left, and right.
About crop and save
• The screen currently displayed is saved as it
was trimmed after you press B/b/v/V to
move the enlarged image and then press the
MENU button.
• You can select [Save as new image] or
[Overwrite] by pressing the MENU button
when the image is enlarged or reduced. Press
v/V to select the method used to save the
image.
• If you select [Save as new image], the image
is saved as a new image.
• If you select [Overwrite], the image is
overwritten. A confirmation screen is
displayed when you select [Overwrite]. Press
v/V to select [Yes] and then press
to
save the image. Press
again when the
confirmation screen is displayed after saving
is finished.
Notes
• Enlarging an image may reduce the quality
depending on the image size.
• It is not possible to enlarge an image using the
buttons on the photo frame.
40 GB
Rotating an image
Press ROTATE (
control.
Tips
) on the remote
Each press of the button rotates the image 90
degrees counter-clockwise.
• For an internal memory image, image rotation data
will be retained even after the power is turned off.
• You can rotate the image of the index image
display.
Operate from the menu of the
photo frame
1
Press MENU in single display mode.
The menu is displayed.
2
(Editing)
Advanced operations
Press B/b to select the
tab.
The screen used for editing is displayed.
3
Press v/V to select [Rotate] and
then press
.
The Rotate menu is displayed.
4
Press v/V to select the direction to
rotate and then press
.
•
:
Rotates the image 90 degrees
clockwise.
•
:
Rotates the image 90 degrees counterclockwise.
5
Press v/V to select [OK] and then
press
.
Note
An enlarged image cannot be rotated.
41 GB
Changing the settings of
the auto power on/off
function
5
Set the time setting.
[Simple]
The timer function to turn the photo frame on/
off automatically can be set. Main power needs
to be switched ON for this function.
1
Press MENU.
The menu is displayed.
2
Press B/b to select the
(Settings) tab.
The settings screen is displayed.
3
Press v/V to select [Auto power ON/
OFF] and press
.
The screen used for setting a value for
[Auto power ON/OFF] is displayed.
1 Press v/V to select [Auto power ON/
OFF] and then press
.
2 Press v/V to select [Enable] and then
press
.
3 Set the auto on/off timer.
Press v/V to set the time you want.
AM or PM is displayed on the right of
the screen when you select [12 hours]
on the time display setting.
4 Set the auto ON/OFF day.
Press v/V to select the day you want to
use this function and then press
to
check. Press v/V to select [OK] and
then press
.
[Advanced]
4
Press v/V to select [Setup method],
and press
. Then press v/V to
select [Simple] or [Advanced], and
press
.
[Simple]: Sets the auto power ON/OFF
function finely in one minute increments.
[Advanced]: Sets the auto power ON/OFF
function according to a day of the week by
one hour units.
42 GB
1 Press B/b/v/V to select the time you
want to use the auto power on/off
function.
You can set this function according to a
day of the week by one hour units.
The color of the selected time zone
changes to blue after you press
. The
power supply of the photo frame will be
turned on when the blue time zone time
occurs. The color of the selected time
zone changes to gray, after you select
the blue time zone and then press
.
The power supply of the photo frame is
turned off while it is in the gray time
zone.
Tip
The power is turned off automatically at the
time you set for [Auto power OFF] when
you are using the photo frame.
The power is turned on automatically at the
time you set for [Auto power ON] during the
standby mode.
2 Press B/b/v/V to select [OK].
Using the alarm function
You can use the photo frame as an alarm clock.
Setting the alarm
Set to the alarm switch on the rear panel
to ON.
Under condition of main power switch set to
“On”, the alarm sound and alarm mode screen
will appear at the scheduled alarm time.
Advanced operations
To turn off the alarm
Set the alarm switch on the rear panel to OFF.
The alarm is stopped although an alarm screen
continues to be displayed.
The normal screen is displayed after you press
any button on the photo frame other than 1
(on/standby).
Continued
43 GB
Setting the time to be alarmed
1
2
Press MENU.
You can change the following settings.
The menu is displayed.
•
•
•
•
•
Press B/b to select the
(Settings) tab.
The settings screen is displayed.
3
Changing the settings
Press v/V to select [Alarm Setting]
and press
.
Slideshow Settings
Alarm Setting
Auto power ON/OFF
Date/time settings
General Settings (Listing Order, Sony logo
ON/OFF etc,.)
• Language setting
• Initialize
Setting procedure
1
Press MENU.
The menu is displayed.
4
Press v/V to set the time you want.
Tips
• To set the clock, refer to “Setting the current time”
(page 20).
• Auto power on/off will not function during alarm is
set off.
• When alarm sets off at scheduled time, power will
also turn on regardless of auto off settings. Main
power needs to be set at ON for alarm to operate.
44 GB
2
Press B/b to select the
(Settings) tab.
The settings screen is displayed.
3
Press v/V to select the item you
want to change and then press
.
The setting screen of the selected item is
displayed.
Tip
You can also use the MENU button on the photo
frame.
For example, when [Slideshow Settings]
is selected.
Press v/V to select the item you
want to change and then press
Advanced operations
4
.
This enables you to set each of the items
(page 46).
Note
When the photo frame is, for instance,
displaying a slideshow, some settings of some
items cannot be changed. They are displayed in
gray and cannot be selected.
5
Press v/V to select a setting value
and then press
.
Each time you press v/V (v/V from the
photo frame), the setting value changes. In
the case of a numerical value, press V to
increase the value and press v to decrease
the value.
If you press
, the setting is confirmed.
6
Press MENU.
The menu closes.
To reset to factory default
settings
1
Press MENU and then select
(Settings) [Initialize] by pressing B/b/v/V.
2
Press v/V to select [Reset] and then press
.
All adjusted values, except for the clock
settings, are reset to the default settings.
Continued
45 GB
Items to set
*: Factory default settings
Item
Setting
Slideshow
Settings
Refer to “Enjoying a slideshow” (page 29).
Alarm Setting
Sets the specific time for an alarm. (.page 43)
Auto power
ON/OFF
Sets the timer function which turns the power supply of the photo frame on or off,
automatically. You can use this function with the following settings. (.page 42)
Simple
Advanced
Setup method
Description
Power-ON
timer
You can set the timer (time/day) and input time for the
power to turn on automatically, when you set this
function to enable.
Power-OFF
timer
You can set the timer (time/day) and input time for the
power to turn off automatically, when you set this
function to enable.
OK
Returns to the previous screen after confirming the
operation.
Cancel
Returns to the previous screen after cancelling the
operation.
Reset all
Deletes all the selected times.
Advanced*
Sets the auto power ON/OFF function according to a
day of the week by one hour units.
Simple
Sets the auto power ON/OFF function finely in one
minute increments.
Date/time
settings
Sets the date, time, first day of a week, etc. (.page 20)
General
Settings
Listing Order
Number Order*
Displays images in order of file name.
Shoot. Date
Displays images in order of shooting date.
Auto display
orientation
ON*/OFF: You can set the photo frame to automatically detect and rotate
the orientation of images.
LCD backlight
Allows you to set the brightness of the backlight of the LCD screen to a
level from 1 to 10*.
Beep
ON*/OFF: Sets the beep sound on/off.
Image file size
Album*
Compresses images and saves them in the internal
memory, that you can save more images. Be aware that
deterioration in image quality compared to the original
images is noticeable when the images are displayed on
a large monitor via a computer.
Original
Saves images to the internal memory without
compressing them. There is no deterioration, but you
can save fewer images.
Sony logo ON/
OFF
46 GB
Sets the display order of images. This setting affects the order in
[Slideshow Settings].
ON*/OFF: You can set whether the photo frame's Sony logo lights or not.
*: Factory default settings
Item
Setting
Description
System
Information
Version
Displays the version of the firmware of the photo frame.
Internal
memory
Memory
capacity
Indicates the maximum amount of space available in
internal memory in the initial state.
Remaining
capacity
Indicates the amount of free space currently available
in internal memory.
Bluetooth
Address
Language
setting
Displays when the Bluetooth adapter is connected to the photo frame.
Sets the display language on the LCD screen.
Japanese, English*, French, Spanish, German, Italian, Russian, Korean, Simplified Chinese,
Traditional Chinese, Dutch, Portuguese, Arabic, Persian, Hungarian, Polish, Czech, Thai,
Greek, Turkish, Malay, Swedish, Norwegian, Danish, Finnish
Note
Default language setting may vary in some regions.
Format internal
memory
You can format the internal memory.
Notes
• All the images added to the internal memory will be deleted.
• Do not format the internal memory by using a connection to a PC or
other external device.
Reset
Returns all settings to their factory defaults except for the current date and
time setting of the [Date/time settings].
47 GB
Advanced operations
Initialize
Displaying images on a
USB memory
For details on the slideshow, refer to
page 29. For details on adding images to
the internal memory, refer to page 32.
Notes
You can connect a mass-storage-complaint
USB memory device to the photo frame and
display an image directly from the USB
memory.
Notes
• We cannot guarantee connection with all types of
mass storage devices.
• The playback device will be switched to the USB
memory if you connect the USB memory to the
USB A/Bluetooth jack during playback the internal
memory.
1
2
3
Connect the photo frame to the AC
power source. (.page 18)
Turn the photo frame to ON.
(.page 19)
Connect the USB memory to the
USB A/Bluetooth connector.
USB memory
4
Select the playback device.
(.page 40)
An image on the USB memory is
displayed on the screen.
48 GB
• When using a commercially available USB cable,
use an A-Type USB cable that is less than 3 meters
long.
• Do not disconnect the USB memory or turn the
photo frame off while the access lamp on the USB
memory is flashing. Doing so may damage the data
stored on the USB memory. Sony assumes no
responsibility for any damage or loss of data.
• A USB hub or USB device with a built-in USB hub
may not work properly.
• The photo frame cannot use data that has been
encrypted or compressed using, for instance,
fingerprint authentication or a password.
Using an external device (with Bluetooth)
Transferring images
using Bluetooth
You can connect a Bluetooth adaptor (optional)
to the USB A/Bluetooth connector of the photo
frame and transfer images from a Bluetooth
compatible mobile phone or other device. The
transferred images are saved in internal
memory.
1
2
3
Connect the photo frame to the AC
power source. (.page 18)
Turn the photo frame to ON.
(.page 19)
Connect the Bluetooth adaptor
(optional) to the USB A/Bluetooth
connector.
is displayed on the upper portion of
the screen when the guide is displayed.
Note
Note
If any device, other than the Bluetooth adaptor,
such as a memory card, camera, PC, or other
USB memory device or a USB cable is
connected to any of the memory card slots, or
the USB A/Bluetooth connector, disconnect it
from the photo frame and then connect the
Bluetooth adaptor.
You cannot send a file to other Bluetooth compatible
devices from the photo frame.
4
You can display the address from [System
Information]. (page 46)
What is a “Profile”?
A profile consists of the standards that enable
Bluetooth wireless communication. There are
several profiles available, depending on the
purposes and product to be used. To make
Bluetooth communication possible, the devices
used in the communicated should support the
same profile.
Compatible image file formats that can
be displayed
See page 64.
Maximum number of pixels that can be
handled
See page 64.
Check the Bluetooth address of the
photo frame.
Tip
The address is displayed only when the
Bluetooth adaptor is connected.
5
Transfer an image from the
Bluetooth-compliant mobile phone,
or other device to the photo frame.
The image transferred is saved on the
internal memory.
Note
You cannot transfer an image to the memory
card of a digital photo frame.
Continued
49 GB
Using an external device (with Bluetooth)
Compatible profiles for Bluetooth
communication
The DPF-D82/D92 supports the following
profiles:
• BIP (Basic Imaging Profile)
Image Push Responder
• OPP (Object Push Profile)
Object Push Server
For the profiles that your Bluetooth device
supports, please refer to its manual.
– Where a wireless LAN is established or a
microwave oven is being used near-by, or other
electromagnetic waves are emitted.
• We cannot guarantee that this product works with
all devices enabled with Bluetooth wireless
technology.
• Sony cannot assume any responsibility for any
information leakage that may be caused by the use
of Bluetooth communications.
• Sony cannot accept responsibilities for any failure
to satisfy the protection requirements resulting from
a non-recommended modification or use of the
product.
For customer support information, please refer to
the operating instructions of the photo frame.
Bluetooth
compatible mobile
phone
To select the photo frame from a
Bluetooth-compliant device, select “Sony
DPF-D92 ##,” “Sony DPF-D82 ##.”
(“##” stands for the two figures from the
right of the address displayed in [System
Information].)
When input of Passkey* is required
Input “0000.” You cannot change the
Passkey with the photo frame.
* A Passkey is often referred to as a “pass
code” or “PIN code.”
Notes
• We cannot guarantee that this product works with
all devices enabled with Bluetooth wireless
technology.
• Do not use the DPPA-BT1 outside the area you
purchased it. Depending on the area, the use of this
product may violate the local radio wave
regulations and may be subject to penalty.
• The communication distance of the product may
vary depending on the obstacles between the
product (a human body, metal objects, or a wall)
and the mobile phone or other device.
• The sensitivity of the Bluetooth communication
may be affected under the following conditions:
– When there is an obstacle between the product
and the mobile phone or other product such as a
human body, metal objects, or a wall.
50 GB
P Caution
• Radio waves from a Bluetooth device may
adversely affect the operation of electrical and
medical devices, and could lead to accidents due to
malfunctions. Make sure to turn off the product and
mobile phone and do not use this product in the
following places:
– Inside hospitals, trains, airplanes, gas stations or
other places where flammable gas may be
present.
– near automatic doors or fire alarms or other
automatically controlled devices.
– near medical equipment.
• Keep this product at least 22 cm away from cardiac
pacemakers. Radio waves from this product may
adversely affect the operation of cardiac
pacemakers.
Using an external device (with a computer)
Connecting to a
computer
You can connect to a computer to view and
copy images from the internal memory of the
photo frame to the computer, and copy images
from the computer to the photo frame.
System requirements
To connect a computer to the picture frame,
your computer must satisfy the following
recommended system requirements.
Connecting to a computer to
exchange images
Note
This section shows an example for a connection for
Windows Vista. Depending on the OS you use, the
screen display and procedures may vary.
1
2
Connect the photo frame to the AC
power source. (.page 18)
Connect the computer and photo
frame with a commercially available
USB cable.
x Windows
Recommended OS: Microsoft Windows Vista
SP1/Windows XP SP3/Windows 2000
Professional SP4
Port: USB port
Recommended OS: Mac OS X (10.4 or later)
Port: USB port
To USB B
connector
Notes
• If multiple USB devices are connected to a
computer or if a hub is used, a problem may occur.
In such a case, simplify the connections.
• You cannot operate the photo frame from another
USB device being used simultaneously.
• Do not disconnect the USB cable during data
communication.
• Operation with all computers that satisfy the
recommended system requirements is not
guaranteed.
• The photo frame has been demonstrated as operable
when connected to PC or Sony digital photo printer.
When other devices are connected to the photo
frame, these devices may not recognize the internal
memory of the photo frame.
Computer
To USB connector
Note
Use a B-Type USB cable that is less than 3
meters long.
3
Turn the photo frame to ON.
(.page 19)
Continued
51 GB
Using an external device (with a computer)
x Macintosh
4
When the [AutoPlay] window
appears on the computer display,
click [Open folder to view files].
If the [AutoPlay] window does not appear,
click [Computer (My Computer)] in the
Start menu, and then open the removable
disc.
5
Move the cursor in this window and
right click, and then click [New] [Folder].
Name this new folder. In this manual, the
folder name “sony” is used as an example.
fewer images may be able to be saved to the internal
memory of the photo frame.
• Image files made or edited on a computer may not
be displayed. Image files set to “Read Only” on a
computer cannot be deleted on the photo frame.
Cancel “Read Only” before saving image files from
a computer on the photo frame.
Disconnecting your computer
Disconnect the USB cable or turn the photo
frame to OFF after disconnecting it from your
computer.
1
2
3
6
7
Double click to open this “sony”
folder.
Open the folder that contains the
image files you want to copy, and
then copy the image files by using
drag-and-drop.
Notes
• When saving images from a computer in the
internal memory, make a folder in the internal
memory and save the images in this folder. If you
do not make a folder, you can only save up to 512
images. In addition, the number of images may be
reduced depending on the file name length or
character type.
• A paticular image may not be displayed in order of
the shooting date on the index image display, etc as
the information on the shooting date may have been
changed or lost when you edited or saved that image
file on a computer.
• When images from the computer are saved in the
internal memory of the photo frame, the image files
are saved without being compressed. As a result,
52 GB
Double-click
on the Task Tray.
Click
(USB Mass Storage
Device) t [Stop].
Click [OK] after checking the drive
you want to remove.
Error messages
If an error message appears
If an error occurs, one of the following error messages may be displayed on the LCD screen of the
photo frame. Follow the corresponding solution below to solve the problem.
Error message
Meaning/Solutions
No Memory Stick. / No
CompactFlash card. / No SD
Memory Card. / No xD-Picture
Card. / No External Device.
• A memory card is not inserted in a slot. Or, an external
device is not connected to the USB A/Bluetooth connector.
Insert a memory card in the corresponding slot. Or, connect
an external device. (.pages 21, 48)
An incompatible Memory Stick is • An unsupported memory card is inserted. Or, an
inserted. / An incompatible
unsupported external device is connected to the
CompactFlash card is inserted. / An
USB A/Bluetooth connector. Use a memory card or
incompatible SD Memory Card is
external device that is supported by the photo frame.
inserted. / An incompatible xDPicture Card is inserted. / An
incompatible External Device is
inserted.
• There is no image file that can be displayed on the screen
of the photo frame on the memory card or the external
device. Use a memory card or on external device
containing image files that can be displayed with the photo
frame.
Cannot delete a protected image.
• To delete a protected file, cancel the protection on your
digital camera or computer.
Media is protected. Remove
protection then try again.
• The memory card is write-protected. Slide the writeprotect switch to the enable position. (.page 62)
The Memory Stick is full. / The
• No more data can be saved because the memory card, the
CompactFlash card is full. / The SD
internal memory, or the external device is full. Delete
Memory Card is full. / The xDimages, or use a memory card or external device with free
Picture Card is full. / The External
space available.
Device is full.
Continued
53 GB
Error messages
No images on file.
Error message
Meaning/Solutions
Error reading the Memory Stick. / • An error has occurred. If this error message is displayed
Error reading the CompactFlash
frequently, check the status of the memory card or external
card. / Error reading the SD
device with a device other than the photo frame.
Memory Card. / Error reading the
• In the case of an external device:
xD-Picture Card. / Error reading
The external device may be write-protected. Cancel the
the internal memory./ Error reading
write-protection setting for the device you are using. The
the External Device.
internal memory of a digital camera may be writeprotected.
Write error in the Memory Stick. /
• For an internal memory:
Write error in the CompactFlash
card. / Write error in the SD
Initialize the internal memory.
Memory Card. / Write error in the
Note
xD-Picture Card. / Write error in
When you initialize the internal memory, please note that all the
the internal memory./ Write error in
image files added to the album are deleted.
the External Device.
The Memory Stick is read only.
• A “Memory Stick-ROM” is inserted. To save the images,
use the “Memory Stick” recommended.
The Memory Stick is protected.
• A protected “Memory Stick” is inserted. To edit and save
the images, use an external device to remove protection.
Media format not supported.
• For a memory card, use your digital camera or other device
to format the memory card.
• For the internal memory, initialize it with the photo frame.
Note
When you initialize the media, all the files on the media will be
deleted.
Cannot open the image.
• The photo frame cannot display or open an image file
whose format is not supported.
No more USB hubs can be
connected.
• Connect the device directly to the photo frame, or use a
device without a built-in USB hub.
Incompatible USB device. Check
device’s USB settings.
• Connect a device with support for mass storage. If the USB
setting of your device is incorrect, set the mass storage
mode in the USB setting.
54 GB
Troubleshooting
If trouble occurs
Before submitting the photo frame for repair, try using the following guidance to solve the problem.
If the problem persists, consult with your Sony dealer or Sony service facilities.
Power supply
Symptom
Check item
Cause/Solutions
The power cannot
be turned on.
• Is the AC power plug
inserted correctly?
c Insert the power plug properly.
Displaying images
If the power is turned on but images are not displayed or the settings of the operation screen cannot
be configured, confirm the following check items.
Symptom
Check item
No images are
displayed on the
screen.
• Is a memory card inserted or c Insert a memory card or connect an
an external device connected
external device properly. (.pages 21,
properly?
49)
• Does the memory card
contain images saved with a
digital camera or other
device?
• Are images stored on the
external device?
Cause/Solutions
c Insert a memory card containing images
or connect an external device containing
images.
c Check the file formats that can be
displayed. (.page 64)
• Is the file format compatible c A file that is not compatible with DCF
with DCF?
may not be able to be displayed with the
photo frame, even if it can be displayed
with a computer.
• Were these images saved
c The information on the shooting date may
from a computer?
be changed or lost when you edit or save
• Were these images edited on
an image file on a computer.
a computer?
Continued
55 GB
Troubleshooting
Images are not
played back in the
order of shooting
date.
Symptom
Check item
Cause/Solutions
Some images are
not displayed.
• Are the images displayed in
the index view?
c If the image is displayed in the index view
but cannot be displayed as single image,
the image file may be damaged even
though its thumbnail preview data is fine.
c A file that is not compatible with DCF
may not be able to be displayed with the
photo frame, even if it can be displayed
with a computer.
• Does the mark displayed
below appear in the index
view?
c If the mark shown on the left is displayed,
the image file may not be supported by the
photo frame because, for example, it is a
JPEG file that was created with your
computer. Also, the image file may be
supported, but not contain thumbnail data.
Select the mark and press
to change
the screen to the single image display. If
the mark on the left is displayed again, the
image cannot be displayed because the
image file is not supported by the photo
frame.
• Were the images created
with an application on a
computer?
• Does the mark displayed
below appear in the index
view?
c If the mark shown on the left is displayed,
the image file is supported by the photo
frame, but the thumbnail data or image
itself cannot be opened. Select the mark
and press
. If the mark shown on the
left is displayed again, the image cannot
be displayed.
• Are there more than 9,999
images in the memory card
or external device?
c The photo frame can play, save, delete, or
otherwise handle up to 9,999 image files.
• Did you rename the file with c If you named or renamed the file on your
a computer or other device?
computer and the file name includes
characters other than alphanumeric
characters, the image may not be able to
be displayed on the photo frame.
• Is there a folder with more
c The photo frame cannot display images
than 8 levels in its hierarchy
saved in a folder that is more than eight
on the memory card or in the
levels deep.
external device?
56 GB
Symptom
Check item
The file name is
not displayed
properly.
• Did you rename the file with c If you named or renamed the file on your
a computer or other device?
computer and the file name includes
characters other than alphanumeric
characters, the file name may not be able
to be displayed properly on the photo
frame. Also, for a file created on a
computer or other device, a maximum of
ten characters from the beginning of the
file name can be displayed.
Cause/Solutions
Note
Only alphanumeric characters can be displayed.
Blank areas appear • Is the image extremely tall or c If an image is extremely tall or wide,
at the top and
wide?
blank areas may appear because of the
bottom.
ratio between the height and width.
Saving and deleting images
Symptom
Check item
Cause/Solutions
Cannot save an
image.
• Is the memory card writeprotected?
c Cancel write-protection and try saving
again.
• Is the write-protect switch of c Slide the write-protect switch to the
the memory card in the
enable position.
[LOCK] position?
c Replace the memory card with one with
sufficient free space. Or, delete any
unwanted images. (.page 36)
• Is the internal memory full?
c Delete any unwanted images.
(.page 36)
• Did you save images from a
computer to the internal
memory without making a
folder in the internal
memory?
c If you do not make a folder, you can only
save up to 512 images. In addition, the
number of images may be reduced
depending on the file name length or
character type. When you save images in
the internal memory from a computer, be
sure to make a folder in the internal
memory and save the images in this
folder.
Continued
57 GB
Troubleshooting
• Is the memory card full?
Symptom
Check item
Cause/Solutions
Cannot delete an
image.
• Is the memory card writeprotected?
c Use the device you are using to cancel
write-protection and try deleting again.
• Is the write-protect switch of c Slide the write-protect switch to the
the memory card in the
enable position.
[LOCK] position?
• Are you using a “Memory
Stick-ROM”?
c It is not possible to delete an image from
or format a “Memory Stick-ROM”.
• Is this image protected?
c Check the image information from the
single view mode. (.page 28)
c An image with a
mark is set to Read
Only. You cannot delete it on the photo
frame.
An image was
deleted
accidentally.
—
c An image cannot be recovered once it is
deleted.
Connecting a external device
Symptom
Check item
Nothing happens
even if the USB
cable is
disconnected and
then re-connected.
Cause/Solutions
—
c An over current error may have occurred
with the photo frame. To recover from the
error, turn the power of the photo frame
off and then back on.
Photo frame
Symptom
Nothing happens
even if you operate
the photo frame.
58 GB
Check item
Cause/Solutions
—
c Push the reset switch on the back of the
photo frame using a long, thin object such
as a pin, etc. (.page 12)
c Set the power switch to off, and then set it
to on again. (.page 12)
Remote control
Symptom
Check item
Cause/Solutions
Nothing happens
• Is the battery inserted in the
even if you operate
remote control properly?
the remote control.
—
• Is there a protective sheet
inserted?
c Replace the battery. (.page 15)
c Insert a battery. (.page 15)
c Insert a battery in the proper orientation.
(.page 15)
c Point the top end of the remote control
towards the remote sensor on the photo
frame. (.page 15)
c Remove any obstruction between the
remote control and the remote sensor.
c Remove the protective sheet.
(.page 15)
Troubleshooting
59 GB
Additional information
Precautions
Safety
• Be careful not to set or drop any heavy
objects on the power cord, or to damage the
power cord in any way. Never operate this
photo frame with a damaged power cord.
• Should any solid object or liquid fall into the
cabinet, unplug the photo frame and have it
checked by qualified personnel before
operating it any further.
• Never disassemble the photo frame.
• To disconnect the power cord, pull it out by
the plug. Never pull the power cord itself.
• When the photo frame is not going to be
used for an extended period of time,
disconnect the power cord from the wall
outlet.
• Do not handle the photo frame roughly.
• To reduce the risk of electrical shock, always
unplug the photo frame from the electrical
outlet before cleaning and servicing the
photo frame.
Installation
• Avoid placing the photo frame in a location
subject to:
– vibration
– humidity
– excessive dust
– direct sunlight
– extremely high or low temperatures
• Do not use electrical equipment near the
photo frame. The photo frame will not work
properly in electromagnetic fields.
• Do not place heavy objects on the photo
frame.
On the AC adaptor
• Even if your photo frame is turned off, AC
power (house current) is still supplied to it
60 GB
•
•
•
•
while it is connected to the wall outlet via the
AC adaptor.
Be sure to use the AC adaptor supplied with
the photo frame. Do not use other AC
adaptors, as this may cause a malfunction.
Do not use the supplied AC adaptor for other
devices.
Do not use an electrical transformer (travel
converter), as this may cause overheating or
a malfunction.
In case the cord of the AC adaptor is
damaged, do not use it any longer, as this
may be dangerous.
On moisture condensation
If the photo frame is brought directly from a
cold location to a warm location or placed in an
extremely warm or humid room, moisture may
condense inside the unit. In such cases the
photo frame will probably not work properly
and may even develop a fault if you persist in
using it. If moisture condensation occurs,
unplug the AC adaptor of the photo frame and
do not use the photo frame for at least one hour.
On transport
When you transport the photo frame, remove
the memory card, external devices, AC adaptor,
and connected cables from the photo frame and
put the photo frame and its peripherals in the
original box with the protective packaging.
If you no longer have the original box and
packing parts, use similar packing material so
that the photo frame will not be damaged while
being transported.
Cleaning
Clean the photo frame with a soft dry cloth, or a
soft cloth lightly moistened with a mild
detergent solution. Do not use any type of
solvent, such as alcohol or benzine, which may
damage the finish.
Restrictions on duplication
TV programs, films, video tapes, portraits of
other people, or other materials may be
copyrighted. Unauthorized use of such
materials may infringe the provisions of the
copyright law.
Disposing of the photo frame
Even if you perform [Format internal memory],
the data in the internal memory may not be
erased completely. When you dispose of the
photo frame, we recommend that you
physically destroy the photo frame.
About memory cards
“Memory Stick”
Types of “Memory Stick” that
the photo frame can use
With the photo frame, you can use the
following types of “Memory Stick”*1:
Type of “Memory
Stick”
Displaying
Deleting/
Saving
“Memory Stick”*2
(Not compatible
with
“MagicGate”)
OK
OK
“Memory Stick”*2
(Compatible with
“MagicGate”)
OK*5
OK*5
“MagicGate
Memory Stick”*2
OK*5
OK*5
“Memory Stick
PRO”*2
OK*5
OK*5
“Memory Stick
PRO-HG”*2
OK*5*6
OK*5*6
OK*5
OK*5
“Memory Stick
Micro”*3 (“M2”*4)
*1
*2
*4
*5
Continued
61 GB
Additional information
*3
The photo frame supports FAT32. The photo
frame has been demonstrated as operable with a
“Memory Stick” with a capacity of 16 GB or less
manufactured by Sony Corporation. However, we
do not guarantee the operations of all the “Memory
Stick” media.
The photo frame is equipped with a slot compatible
with both standard-size and Duo-size media.
Without a “Memory Stick Duo” adaptor, you can
use both a standard-size “Memory Stick” and the
compact-size “Memory Stick Duo”.
When using a “Memory Stick Micro” with the
photo frame, always insert it into an M2 adaptor.
“M2” is an abbreviation for “Memory Stick
Micro”. In this section, “M2” is used to describe a
“Memory Stick Micro”.
Data reading/recording that requires “MagicGate”
copyright protection cannot be performed.
“MagicGate” is the general name of a copyright
*6
protection technology developed by Sony using
authentication and encryption.
The photo frame does not support 8 bit parallel
data transfer.
Notes on use
• For the latest information on the “Memory
Stick” types that the photo frame supports,
see the “Memory Stick” compatibility
information on the Sony web site:
http://www.memorystick.com/en/support/
support.html
(Select the area where you use your photo
frame, and then select “Digital Photo Frame”
from each area page.)
• Do not insert more than one “Memory Stick”
at the same time, or this may cause trouble
with the photo frame.
• If you use a “Memory Stick Micro” with the
photo frame, the “Memory Stick Micro”
needs to be inserted into an “M2” adaptor.
• If you insert a “Memory Stick Micro” into
the photo frame without an “M2” adaptor,
you may be unable to remove the “Memory
Stick Micro”.
• If you insert a “Memory Stick Micro” into an
“M2”adaptor, and insert the “M2” adaptor
into a “Memory Stick Duo” adaptor, the
photo frame may not operate properly.
• When you initialize a “Memory Stick”, use
the initialization function of your digital
camera. If you initialize it with your
computer, images may not be displayed
properly.
• When you perform initialization, all the
protected images are erased. To avoid
erasing important data by accident, make
sure to check the contents of the “Memory
Stick” before initialization.
• You cannot record, edit, or delete data if you
slide the write-protect switch to LOCK.
• Do not attach any other material than the
supplied label on the labelling position.
When you attach the supplied label, be sure
to attach it to the labelling position. Be
careful that the label does not stick out.
62 GB
SD memory card
The SD memory card slot of the photo frame
allows you to use the following:
• SD memory card*1
• miniSD card, microSD card
(An adaptor is necessary.)*2
• SDHC memory card*3
• MMC standard memory card*4
We do not guarantee proper operations for all
types of SD memory cards and MMC standard
memory cards.
*1
*2
*3
*4
The photo frame has been demonstrated as
operable with an SD memory card with a capacity
of 2 GB or smaller.
Some commercially available card adaptors have
projected terminals on the back. This type of
adaptor may not work properly with the photo
frame.
The photo frame has been demonstrated as
operable with an SDHC memory card with a
capacity of 32 GB or less.
The photo frame has been demonstrated as
operable with an MMC standard memory card with
a capacity of 2 GB or less.
Notes on use
Data reading/recording that requires copyright
protection cannot be performed.
xD-Picture Card
With the xD-Picture Card slot of the photo
frame, you can use an xD-Picture Card*5. Not
all the memory card operations are supported
and we do not guarantee proper operations for
all types of xD-Picture Card.
*5
The photo frame has been demonstrated as
operable with an xD-Picture Card with a
capacity of 2 GB or less.
CompactFlash card
The CompactFlash card slot of the photo frame
allows you to use the following:
• CompactFlash Memory Card (Type I/
Type II) and CF+Card (Type I/Type II)compatible CompactFlash Card*6
• Microdrive
You can also use the Smart Media card by
using a commercially available CompactFlash
card adaptor*7.
However, we do not guarantee proper
operations for all types of CompactFlash cards.
*6
*7
Use a CompactFlash card with a power
specification of 3.3V or 3.3V/5V. You cannot use
a type for 3V or 5V only. Do not insert other types
of CompactFlash card into the photo frame’s
insertion slot. The photo frame may be damaged.
The photo frame has been demonstrated as
operable with a CompactFlash with a capacity of
32 GB or smaller.
When using a commercially available
CompactFlash card adaptor, refer to the operating
instructions of the adaptor you use for how to
install the card and adaptor. When using a
CompactFlash card adaptor, a write-protected card
may not work properly.
• Do not disassemble or modify a card.
• Do not expose a card to water.
• Do not use or store a card under the
following conditions:
– Locations beyond the required operational
conditions including locations such as the
hot interior of a car parked in the sun and/
or in the summer, the outdoors exposed to
direct sunlight, or a place near a heater.
– Humid locations or locations with
corrosive substances present
– Locations subject to static electricity or
electrical noise
Notes on using a memory card
Additional information
• When using a card, make sure to check the
correct insertion direction of the card and the
correct insertion slot.
• When inserting the memory card, it will only
insert part of the way, so do not try to force
it, as this could damage the memory card
and/or photo frame.
• Do not remove a card or turn off the photo
frame while the photo frame is reading or
writing data, or the access indicator is
flashing. Otherwise, data may be rendered
unreadable or be erased.
• We recommend that you save a backup of
important data.
• Data processed with the computer may not
be displayed with the photo frame.
• When you carry or store a card, put it in the
case supplied with it.
• Do not touch the terminal of a card with your
hand or a metal object.
• Do not strike, bend or drop a card.
63 GB
D:\DPF series\V Series\4129231131\4129231131\4129231131DPFD92CED\01GB-DPFD92CED\100ADD.fm
Master: Left
100ADD.fm Page 64 Wednesday, April 8, 2009 9:04 AM
Specifications
x Photo frame
LCD screen
LCD panel:
DPF-D92: 9.0 inches, TFT active
matrix
DPF-D82: 8.0 inches, TFT active
matrix
Total number of dots:
DPF-D92/D82: 1,152,000
(800 × 3(RGB) × 480) dots
Display aspect ratio
15:9
Effective display area
DPF-D92: 8.6 inches
DPF-D82: 7.6 inches
LCD backlight life
DPF-D92/D82: 20,000 hours
(before brightness of the backlight is
reduced to half)
Input/Output connectors
USB connector (TypeB, Hi-Speed USB)
USB A/Bluetooth connector
(TypeA, Hi-Speed USB)
Slots
“Memory Stick PRO” slot
SD memory card/MMC/
xD-Picture Card slot
CompactFlash card/Microdrive slot
Compatible image file formats
JPEG: DCF 2.0 compatible, Exif 2.21
compatible, JFIF*1
RAW (preview only*2): SRF, SR2, ARW
(2.0 or lower version)
(Some image file formats are not
compatible.)
Maximum number of pixels that can be
displayed
8,000 (H) × 6,000 (V) pixels
File system
FAT12/16/32,
sector size of 2,048 bytes or smaller
Image file name
DCF format, 256 characters within 8th
hierarchy
Maximum number of files that can be
handled
9,999 files for a memory card/an external
device
Internal memory capacity*3
DPF-D92/D82: 1 GB
(Approx. 2,000 images*4 can be saved.)
When measuring media capacity, 1 GB
equals 1 billion bytes, a portion of
which is used for data management.
Power requirements
DC IN jack, DC 12V
Power consumption
Model
in operation mode
DPF-D92/
D82
at the maximum load
including the
AC adaptor
normal mode*
11.6W
5.5W
* The definition of the normal mode is a status
which allows the performance of a slideshow using
images stored in the internal memory with the
default settings without inserting a memory card or
connecting an external device.
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Dimensions
[With the stand spread out]
DPF-D92:
Approx. 276 × 189 × 144.1 mm
(10 7/8 × 7 1/2 × 5 3/4 inches)
(width/height/depth)
DPF-D82:
Approx. 243 × 162 × 126.6 mm
(9 5/8 × 6 1/2 × 5 inches)
[When the photo frame is hanging on the
wall]
DPF-D92:
Approx. 276 × 189 × 39.5 mm
(10 7/8 × 7 1/2 × 1 9/16 inches)
(width/height/depth)
DPF-D82:
Approx. 243 × 162 × 39.5 mm
(9 5/8 × 6 1/2 × 1 9/16 inches)
64 GB
DPF-D82/D92 4-129-231-13 (1)
Mass
DPF-D92: Approx. 810 g (1 lb 12 5/8 oz)
DPF-D82: Approx. 720 g (1 lb 9 3/8 oz)
(excluding the AC adaptor)
Included accessories
See “Checking included items” on
page 11.
x AC adaptor
The following are common specifications of
DPF-D92/D82.
Power requirements
- 100 V to 240 V, 50/60 Hz
0.48 A
Rated output voltage
12 V 1.2 A
Dimensions
Approx. 34 × 72 × 69 mm
(1 3/8 × 2 7/8 × 2 3/4 inches)
(width/height/depth)
(excluding the protruding parts)
Mass
Approx. 110 g (4 oz)
See the label of AC adaptor for more details.
Design and specifications are subject to change
without notice.
*1
: Baseline JPEG with 4:4:4, 4:2:2, or 4:2:0 format
: RAW files are displayed as thumbnail preview.
*3
: The capacity is calculated as 1 GB is equivalent to
1 000 000 000 bytes. The actual capacity is
reduced as files for management and applications
are included. Approximately 900 MB on DPFD92/D82 can be used for your actual operation.
*4: Approximate number is shown when the images
taken by 2 000 000 pixels equivalent camera are
saved. The value may vary depending on the
shooting condition.
*2
Additional information
Customer support home page
The latest support information is available at the
following home page address:
http://www.sony.net/
65 GB
Index
A
AC adaptor 18
Accessories 11
Adding to the internal
memory 32
Alarm 43, 46
Associated file 28
Auto power ON/OFF 46
Auto power on/off 42
B
Bluetooth 49
C
Calendar 21
Changing the settings 44
Cleaning 60
Connecting
Computer 51
External device 48
Connecting to the AC power
source 18
D
Date/time settings 20, 46
DC IN 8.4 V 18
Deleting an image 36
Display priority 22
E
Error messages 53
Exporting an image 34
F
Features 9
Format internal memory 47
G
General Settings 46
66 GB
I
Image file size 46
Index image display 27
Initialize 47
System Information 47
System requirements
Macintosh 51
Windows 51
L
T
Language setting 47
Troubleshooting 55
M
U
Mass storage compatible
devices 48
Memory cards 61
“Memory Stick” 61
CompactFlash card 62
Notes on use 63
SD memory card 62
xD-Picture Card 62
USB cable 48
P
Placing in portrait or
landscape orientation 16
Playback device 40
Precautions 60
R
Remote control 15
Replacing the battery of the
remote control 15
Reset 47
Rotating an image 41
S
Searching for an image 39
Setting the stand 16
Single view mode 26
Slideshow display 24
Slideshow Settings 31
Color effect 31
Display Mode 31
Effect 31
Interval 31
Shuffle 31
Specifications 64
W
Write-protect switch 62
Z
Zooming an image in/out 40
Printed using VOC (Volatile Organic
Compound)-free vegetable oil based ink.
Sony Corporation
Printed in China