KYOCERA TASKalfa 181 Manual

This Operation Guide mentions that 181 is a 18 ppm (prints per minute) machine and 221 is a 22
ppm (prints per minute) machine.
Note
This Operation Guide contains information that corresponds to using both the inch and metric
versions of this machine.
This Operation Guide shows messages of the inch version. When using the metric version, see
the messages of the inch version for reference. With regard to the messages in the text, if a
message has only the difference of upper- and lower-case spelling, we show only the message
of the inch version. When there is even a slight difference in the message, we have listed the
information for the inch version followed, in brackets, by the corresponding information for the
metric version.
Trademark Information
•
Microsoft, Windows, Windows NT and Internet Explorer are registered trademarks of
Microsoft Corporation of America and other countries.
•
Windows Me , Windows Server and Windows XP are trademarks of Microsoft Corporation.
•
Ethernet is a registered trademark of Xerox Corporation.
•
IBM and IBM PC/AT are trademarks of International Business Machines Corporation of
America.
•
Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated.
•
PaperPort is a registered trademark of ScanSoft Inc. of America and other countries.
All other company and product names contained in this Operation Guide are trademarks or
registered trademarks of their respective companies. The designations ™ and ® will not be
used in this Operation Guide.
All rights reserved. No part of this material may be reproduced or transmitted in any form or by
any means, electronic or mechanical, including photocopying, recording or by any information
storage and retrieval system, without permission in writing from the Publisher.
Legal Restriction On Copying
•
It may be prohibited to copy copyrighted material without permission of the copyright owner.
•
It is prohibited under any circumstances to copy domestic or foreign currencies.
•
Copying other items may be prohibited.
i
About this Operation Guide
This Operation Guide is meant to be read when the Scanner Interface Card is installed and your
copier is to be used as a network scanner. It explains set-up procedures and other related
operation on the machine.
As the required set-up in order to use the copier as a scanner may differ depending upon the
environment in use in the connected computer, please read those sections related to your
specific computer environment and perform the appropriate set-up procedures explained there.
This Operation Guide should also be read and used together with the appropriate Operation
Guide <Functions Edition> (On-Line Manual) that is on the included CD-ROMs. The On-Line
Manual <Functions Edition> explains how to scan, various setting methods, and operation
procedures from a computer.
Using the Operation Guide <Functions Edition> (On-Line Manual)
The CD-ROMs included with this product contain the Operation Guide <Functions Edition>
(On-Line Manual) in a PDF (Portable Document Format) file format.
The Operation Guide <Functions Edition> (On-Line Manual) explains how to use the required
applications when using your copier as a network scanner. The main content of the CD-ROMs is
as follows:
•
Introduction of the network scanner system
•
Explanation of setting procedures when using an Internet Web browser
•
Explanation of setting procedures at the scanner
•
Explanation of attached utilities:
Scanner File Utility
Address Book
Address Editor
TWAIN Source
Opening the On-Line Manual
Carry out the following procedures in order to open and view the On-Line Manual.
ii
1
Insert the appropriate CD-ROM into the CD-ROM drive of your computer. The Main Menu
screen for set-up will appear automatically.
2
Click on [Documents] under the [Main Menu] in order to access the desired On-Line Manual
for viewing.
Note
Adobe Acrobat Reader must be installed in your computer in order to access the On-Line
Manual. The Adobe Acrobat Reader software is included on the CD-ROMs contained with this
product and can be installed from there directly onto your hard disk.
Important:
The use of scanned legally copyrighted materials, such as documents, musical scores, pictures,
woodblock prints, maps, drawings and photographs, for any intent other than your own personal
or home use, or other such purpose, is prohibited under the copyright law without prior
permission from the legal copyright owner.
Simply scanning the following items may result in legal penalty:
Bank notes, coins, government-issue securities, national bonds, local bonds, foreign currencies
and securities, unused postage stamps, government post cards, government stamps, and
securities regulated by the liquor tax law.
Other items that you should also not scan:
It is additionally recommended that you do not attempt to scan government-issue passports, or
licenses, permits, ID cards, securities, commuter tickets, passes, books of tickets and meal
coupons issued by public organizations or private parties.
iii
Getting connected
The following procedures are required in order to use this machine as a scanner.
Connect the scanner to your computer
<Example connection>
Hub
PC
Connecting the scanner to your computer
network with a network cable
(100BASE-TX and 10BASE-T)
page 2-2
Network cable
Perform the required operation at the scanner
Basic scanner settings
page
(register the host name and IP address, etc.)
Date/time and time difference settings
2-3
page 2-4
Perform the required operation at your computer
Registering and editing user information
Registers users (transmitters) who use the scanner.
See the Online Manual <Functions Edition>.
PC
Installing the various software (included on the enclosed
CD-ROM disk)
Scanner File Utility
Saves the scanned image as a data file on your computer.
TWAIN Source
Enables you to operate scanning from a TWAIN-compatible application.
Address Book
A personal address book that you can access from the scanner’s operation
panel.
Address Editor (Management Tool)
Enables you to register and edit the shared Address Book, make
network-related settings and change various default settings.
Refer to the On-Line Manual <Functions Edition> for more detailed
information on the included software.
You’re now ready to scan!
iv
Table of contents
1
Preparations ................................................................................................... 1-1
Names of parts .........................................................................................................................1-1
Main body ...........................................................................................................................1-1
Operation Panel ..................................................................................................................1-2
Accessories ..............................................................................................................................1-3
Utilities and other software (the main content of the included CD-ROMs) ...............................1-3
Required items .........................................................................................................................1-3
2
Set-up .............................................................................................................. 2-1
Setting up the scanner .............................................................................................................2-1
Outline and network configuration ......................................................................................2-1
Connecting the scanner to your computer network ............................................................2-2
Network (TCP/IP) settings ..................................................................................................2-3
User registration ................................................................................................................2-4
Date/Time and Time Difference ..........................................................................................2-4
Other settings .....................................................................................................................2-5
Setting up the scanner software ...............................................................................................2-6
System requirements ..........................................................................................................2-6
Installing the software .........................................................................................................2-6
Installing the utilities ...........................................................................................................2-7
Installing the TWAIN source ...............................................................................................2-8
3
Performing the Required Operation at the Scanner ................................... 3-1
Scanning under the Scan to PC and Send E-mail functions ....................................................3-1
Before using the Scan to PC function .................................................................................3-1
Before using the Send E-mail function ...............................................................................3-1
How to scan under Scan to PC and Send E-mail ...............................................................3-1
Sending information ............................................................................................................3-3
Scanning with TWAIN ..............................................................................................................3-4
When performing the scanning operation at the scanner ...................................................3-4
When performing the scanning operation at your computer ...............................................3-5
Scan setting .............................................................................................................................3-6
v
vi
1
Preparations
Names of parts
Main body
3
2
6
1
4
5
Important!
1
Original cover — Open and close this cover when setting an original on the platen.
2
Platen — Set the original to be scanned face-down in the left-rear portion of the platen.
3
Original size indicator lines — Be sure to align the original with these lines when setting an
original on the platen.
4
Operation panel — Perform operations here.
5
Main switch — Turn this switch ON (|) when using the scanner.
6
Scanner interface connector — Use to connect the scanner to the computer network with a
10BASE-T or 100BASE-TX cable.
NEVER attempt to remove the Scanner Interface Card.
1-1
Preparations
Operation Panel
1
10
2
7
8
6
4
9
3
1
System Menu/Counter key — Press this key when you want to set the network address, the
date/time, and the time difference of this scanner.
2
Message display — Indicates the scanner condition or setting values.
3
Numeric key — Press these keys when you want to enter a desired value directly. If there is a
number in front of the selection item, you can select the item with these Numeric keys.
4
Stop/Clear key — Press this key when you want to cancel setting and return to the previous
screen.
5
Reset key — Press this key when you want to cancel initial setting change or date/time setting.
6
Scanner key — Press this key when you want to switch the machine to the scanner mode.
When the scanner mode is selected, the scanner indicator will light up.
7
U and V cursor keys — Press these keys to select an item in various settings.
8
< and > cursor keys — Press these keys to change the date/time setting.
9
Enter (OK) Key — Press this key when you want to register a setting. Press this key when
scanning is completed
10 Scan Function Key — The following settings can be adjusted.
•
•
•
•
•
•
•
•
1-2
5
Resolution
File Format
Original Type
Mixed Size Originals
Border Erase
Original Orientation
Continuous Scan
Output Per Page
Preparations
Accessories
Prior to using the scanner for the first time, verify that the following accessories are included with
this product.
•
1 CD-ROM (Product Library)
•
1 CD-ROM (TWAIN application)
•
Operation Guide
Utilities and other software (the main content of the included CD-ROMs)
CD-ROM (Product Library)
Note
•
Scanner File Utility
•
TWAIN Source
•
Address Book
•
Address Editor
•
KM-NET VIEWER
•
KX Driver
•
FAX Driver
•
Release Note
Refer to the On-Line Manual <Functions Edition> of this Operation Guide for information on using
the included utilities and other software.
Required items
You must have on hand one of the following cables as appropriate to your computer network
environment.
Note
•
100BASE-TX cable (shielded type)
•
10BASE-T cable (shielded type)
Be absolutely sure that the 10BASE-T or 100BASE-TX cable that you use is a shielded cable.
1-3
Preparations
1-4
2
Set-up
Setting up the scanner
Outline and network configuration
Example of transmission modes for data scanned using the Scan System and the required software
The software indicated in the thick-lined balloons is included with this product. Install the software
that is appropriate to your operating environment and needs.
Note
Refer to the On-Line Manual <Functions Edition> for information on using the included utilities and
other software.
2-1
Set-up
Connecting the scanner to your computer network
1
Caution
2
Important!
3
2-2
Turn the main switch located on the right side of the
scanner OFF.
ALWAYS turn the main switch to the scanner OFF BEFORE connecting the network cable.
Connect a 10BASE-T or 100BASE-TX cable to the
scanner interface connector located at the back side
of the right side of the scanner.
NEVER attempt to remove the Scanner Interface Card.
Turn the main switch to the scanner back ON ( | ).
Set-up
Network (TCP/IP) settings
This section explains the procedures to set the network address for the scanner.
Notes
•
The network address that should be set here will differ depending upon your network
environment. Check with your network administrator BEFORE performing this setting.
•
If you are using a DHCP server to set the network addresses, you will not need to change the
IP address and the subnet mask because the DHCP has been enabled (ON) as the factory
default setting.
1
Press the System Menu/Counter key to display the
Default setting screen.
2
Use the S and T keys to move D to select Scan
default and then press the Enter key. The password
entry screen will appear.
3
Enter the four-digit management code using the
numeric keys. The password at the factory default
setting is 1800 for the 18 ppm model and 2200 for the
22 ppm model.
Notes
If the management code matches, the screen will change to the Scanner setting screen.
•
Four-digit management code can be changed. Refer to the Operetion Guide of machine.
Use the S and T keys to move D to select DHCP and
then press the Enter key. Screen will change to the
DHCP/BOOTP setting screen.
5
Use the S and T keys to move D to select 1 Off
and then press the Enter key. Screen will return to the
Scanner setting screen of Step 4.
6
7
Enter Pin Code using # key.
•
4
Note
Default setting / Counter
Copy default
Machine default
Scan default
Scan Default:
Subnet
: 255.255.255. 0
Gateway
: 10.181. 12.11
DHCP/BOOTP : On
DHCP/BOOTP
Off
> On
If you are using a DHCP server, select 2 On. In this case, even if you enter each IP address and
subnet mask manually, the entered settings will be ignored.
Use the S and T keys to move D to select IP
address and then press the Enter key. Screen will
change to the IP address setting screen.
Enter the IP address by every three digits with Numeric
keys. Press > key to move to the following three digits.
Check the entered IP address and then press the
Enter key if it is correct. Screen will return to the
Scanner setting screen of Step 6.
Scan Default:
IP Address
Subnet
Gateway
: 10. 181. 15. 11
: 255. 255. 255. 0
: 10. 181. 12. 11
IP Address
10 .
181 .
15 .
11
2-3
Set-up
8
9
Note
10
In the same manner, set Subnet for subnet mask and
Gateway for gateway addresses.
Scan Default:
IP Address
Subnet
Gateway
: 10. 181. 15. 11
: 255. 255. 255. 0
: 10. 181. 13. 11
Once it is complete to enter all network addresses and
returned to the Scanner setting screen of Step 7, use
the S and T keys to move D to select End and then
press the Enter key.
Scan Default:
End
IP Address
Subnet
: 10. 181. 15. 11
: 255. 255. 255. 0
In a network environment with RARP, select RARP and then select On on the Scanner setting
screen. In this case, you will not need to set the IP address manually.
For other network settings, use a web browser or Address Editor.
User registration
To use the scanner, user registration is needed in addition to the network setting. User (transmitter)
registration is performed from a web browser or Address Editor. For details, see the Online Manual
<Functions Edition>.
Date/Time and Time Difference
Sets the required area information for the Send E-mail function. The time of day when email is sent
from the scanner is included in the header of that email message as the transmission time. Perform
the following procedure in order to set the date and time in your area, as well as the time difference
to GMT (Greenwich Mean Time).
2-4
1
Press the System Menu/Counter key.
2
Use the S and T keys to move D to select Machine
Default and press the Enter key. The password
entry screen will appear.
3
Enter the four-digit management code using the
numeric keys. The management code at the factory
default setting is 1800 for the 18 ppm model and 2200
for the 22 ppm model.
4
Use the S and T keys to move D to select
Date/Time and press the Enter key.
5
Use the S and T keys to move D to select the item to
be changed and use the < and > keys to select the
desired setting.
System Menu / Counter
Job Accounting
Copy Default
Machine Default
Enter Pin Code using # key.
Machine Default
Low Power Time
: 15Min.
Key Sound On/Off : On
: 09:35
Date/Time
Date/Time
End
Time
DST
: 09:35
: Off
Set-up
Note
6
Note
Set the time difference and then the date and time.
After completing the settings, move D to select End
and press the Enter key. The settings will be
registered.
Date/Time
End
Time
DST
: 09:35
: OFF
If you change both the summer time and date/time settings, the summer time setting will be ignored.
Other settings
It is possible to change certain default settings for the scanner function. Refer to the Online Manual
for details on each setting.
2-5
Set-up
Setting up the scanner software
System requirements
PC
IBM PC/AT or compatible
OS
Windows 2000 (Service Pack 2 or later), Windows XP,
Windows Server 2003 or Windows Vista
System environment
Recommended environment
CPU
Pentium 133 MHz or faster
RAM
64 MB or more
HDD
20 MB or more
CPU
Celeron 500 MHz or faster
RAM
128 MB or more
HDD
300 MB or more
CD-ROM drive
1 drive
Ethernet cable
10BASE-T or 100BASE-TX
Installing the software
There are three main functions available with this network scanner. Perform the following procedure
in order to install into your computer the required utility that is appropriate to the application and
operating system in use in your computer.
Scan to PC
Stores the image data of scanned originals as a file in a desired folder on your computer. Install the
Scanner File Utility into the corresponding computer in order to use this function.
Note
•
Registration of the save folder in your computer, as well as registration in the scanner of the
destination is required.
•
For information on making settings from an Internet Web browser, as well as for each utility,
refer to the On-Line Manual <Functions Edition> of this Operation Guide.
Send E-mail
Sends the image data of scanned originals to the desired receiver as a file attached to an email
message.
Note
Registration in the scanner of the corresponding SMTP server settings is required. For information
on making settings from an Internet Web browser, as well as for each utility, refer to the On-Line
Manual <Functions Edition> of this Operation Guide.
TWAIN
Connects to the scanner from the TWAIN-compatible application according to the procedures of that
particular application. Install the TWAIN Source on the computer that contains the application in
order to use this function.
2-6
Set-up
Installing the utilities
The following utilities are contained on the CD-ROM that is included with this product.
Note
1
Refer to the On-Line Manual <Functions Edition> of this Operation Guide for information on using
the included utilities.
•
Scanner File Utility
•
Address Book
•
Address Editor (Management Tool)
Run Windows.
Quit all other applications that may be open.
2
Insert the CD-ROM that is included with the scanner into the CD-ROM drive of your computer.
3
The License Agreement will be displayed. If
you agree with the conditions contained
therein, click Accept.
If this screen does not appear after you
insert the CD-ROM, open the CD-ROM
window to access its contents and
double-click on the [setup.exe] file.
4
Click Scanner Tools on the Main Menu.
5
Click on the name of the utility that you want to install. The installation window for that utility will
appear. Follow the instructions on screen in order to install the selected utility.
2-7
Set-up
Installing the TWAIN source
In order to scan originals using PaperPort, TWAIN Source must be installed PRIOR to installing the
PaperPort application.
1
Run Windows.
Quit all other applications that may be open.
2
Insert the CD-ROM that is included with the scanner into the CD-ROM drive of your computer.
3
The License Agreement will be displayed. If
you agree with the conditions contained
therein, click Accept.
If this screen does not appear after you
insert the CD-ROM, open the CD-ROM
window to access its contents and
double-click on the [setup.exe] file.
2-8
4
Click Scanner Tools on the Main Menu.
5
Click TWAIN Source in the Main Menu.
6
The Model Select window will appear. Select the model of the scanner that you are using.
7
When the installation window appears, follow the instructions on screen in order to install the
TWAIN Source.
3
Performing the Required Operation at the
Scanner
Scanning under the Scan to PC and Send E-mail functions
Before using the Scan to PC function
When performing the Scan to PC function, perform the following settings in advance.
1
Install the Scanner File Utility in the destination computer.
2
Run the Scanner File Utility and register the destination folder for the scanned image data.
3
Register the IP address, the registration name, and the destination number of the destination
computer in the scanner using a web browser or Address Editor.
Note
Be sure to enter the same number in the Save folder No. field here as the save folder number (001
– 100) that was registered in the Scanner File Utility.
Refer to the On-Line Manual <Functions Edition> for more detailed information.
Before using the Send E-mail function
Register the destination name and the email address in the scanner using a web browser or
Address Editor.
How to scan under Scan to PC and Send E-mail
1
Press the Scan key to display the Select Scanner
Function screen.
2
Use the S and T keys to select 1 Scan to PC
(SEND TO PC) or 2 Send E-mail.
3
Use the S and T keys to move D to select your user
name and press the Enter key.
Select function.
Scan to PC
Send E-mail
TWAIN
Select Sender (User)
001 USER ABCDE
#---
Notes
•
If a password has been registered for the selected user, you must enter the password. Enter
the password using the numeric keys and press the Enter key.
•
If your user name is not displayed even if the S and T keys are pressed, use a web browser
or AddressEditor to check to see if your user name has been registered.
3-1
Performing the Required Operation at the Scanner
4
Use the S and T keys to move D to select the desired destination. An item can be selected from
Send to User PC (SEND TO USER PC), Private Book, and Common Book. Select the
desired item and press the Enter key.
When storing data in the PC of the transmitter (user):
Move D to select 2 Send to User PC (SEND TO
USER PC) and press the Enter key.
Note
Select Address Book
End
Send to User PC
Private Book
: Off
When registering a transmitter (user), you must set the IP address of the computer.
When selecting a destination (receiver) from the private
address book:
1. Move D to select 3 Private Book and press the
Enter key.
2. Move D to select the desired destination and press
the Enter key.
Notes
Select Address Book
End
Send to User PC
Private Book
: Off
Select destination.
000 Finish to select
001 AdrNOPQRSTUVWXYZ
#---
•
If a password has been registered for the selected destination, you must enter the password.
Enter the password using the numeric keys and press the Enter key.
•
When you enter a displayed number using the numeric keys, the confirmation screen will
appear. When you press the EnterEnter key, the destination will be selected.
•
For the private address book, AddressBook must be started in the computer of the transmitter
(user).
3. If you have selected the destination, move D to
select 000 Finish to select (000 SELECT.
COMPLETE) and press the Enter key.
Select destination.
000 Finish to select
001 AdrNOPQRSTUVWXYZ
#---
When selecting a destination (receiver) from the common
address book:
Move D to select 4 Common Book and press the
Enter key.
Operate in a similar way to the procedure for the
private address book.
Notes
3-2
Select Address Book
Send to User PC
Private Book
Common Book
: Off
•
For the common address book, the destinations must be set with a web browser or
AddressEditor.
•
Up to 20 destinations can be selected at the same time.
Performing the Required Operation at the Scanner
5
Finally move D to select 1 End and press the Enter
key. The scanner setting screen will appear. See Scan
setting on page 3-6.
Select Address Book
End
Send to User PC
Private Book
: Off
Sending information
The history of sending with the Send E-mail and Scan
to PC functions is displayed.
Press the Scanner key, use the S and T keys to
move D to select 4 Sending Information (SEND
INFORMATION), and press the Enter key.
Sending Confirmation List
End
ABCD
ABCD 05:56
EFGH 14:56
EFGH
OK
NG
The sending confirmation list will be displayed. For more details of the history, move D to select the
desired history and press the Enter key.
3-3
Performing the Required Operation at the Scanner
Scanning with TWAIN
The following explains the settings that need to be made in the scanner in order to scan using the
TWAIN function.
When performing the scanning operation at the scanner
3-4
1
Press the Scan key to display the Select Scanner
Function screen.
2
Use the S and T keys to move D to select 3 TWAIN
and press the Enter key. The TWAIN Mode screen will
appear.
3
Set the original that you want to scan.
4
Run the TWAIN Source in the corresponding application. The main dialogue box for the TWAIN
Source will appear. Make any settings that you want, click on the [Connect] button in the dialogue
box and, once the connection to the scanner is made, click on the [Scan] button. Scanning will
begin.
Select function.
Scan to PC
Send E-mail
TWAIN
Performing the Required Operation at the Scanner
When performing the scanning operation at your computer
1
Run the TWAIN Source in the corresponding application. The main dialogue box for the TWAIN
Source will appear. Make any settings that you want, and put a check mark in the [Waiting Scan]
checkbox.
2
Click on the [Connect] button in the main dialogue box and, once the connection to the scanner is
made, click on the [Scan] button.
Note
3
Notes
Putting a check mark in the [Waiting Scan] checkbox will allow you to start the actual scanning
operation by pressing the Start key at the scanner.
Set the original that you want to scan in the scanner
and press the Start key. Scanning will begin.
•
Scan settings can also be made on the operation panel of the scanner. Change any settings
there that you want.
•
If you enter different settings in your computer and in the scanner, the settings made on the
operation panel of the scanner will take priority.
3-5
Performing the Required Operation at the Scanner
Scan setting
The scan setting screen is displayed when scanning originals. To carry out the various settings, perform the following
procedures. After completing the scan settings, if you set an original in the scanner and press the Start key, scanning will
start.
F
J
D
C
Notes
Note
3-6
A
G
B
I
K
H
A
Auto Density key — Press this key to select the automatic exposure setting.
B
Image concentration adjustment key — Press these keys to select an exposure level.
•
7 levels in the normal mode.
•
If the automatic exposure mode is set, all the exposure indicators are off.
C
Original Image Type key — Press this key to select the original image type.
The Photo mode cannot be selected with the Send E-mail function.
D
Original Size key — Press this key to specify the original size.
E
Paper Selection key — Press this key to specify the transmission (image) size. The scanned
original image will be automatically reduced or enlarged to the specified size.
F
Scanner Function key — The following settings can be adjusted.
•
•
•
•
•
•
•
•
Note
E
Resolution
File Format
Original Type
Mixed Size Originals
Border Erase
Original Orientation
Continuous Scan
Output Per Page
For details on each setting, see the Online Manual.
G
Enter (OK) key — Press this key to confirm the setting in various setting screens.
H
Start key — Press this key to start scanning.
I
Stop/Clear key — Press this key to stop scanning, clear an entered value or return to the
previous screen.
J
Scanner key — Press this key to display the Scanner Function screen.
K
Reset key — If you select this key to cancel scan setting, the scan setting screen will appear.
Performing the Required Operation at the Scanner
1
After completing the setting, display the scan setting
screen.
Ready to scan.
100%
2
Set the original.
3
Press the Start key. Scanning the original starts.
4
When Continue scan (MULTIPLE SCAN) is set On
on the scan setting screen, the screen will appear to
select whether to continue scanning originals or not
when scanning is complete.
Notes
Auto
Auto
PDF
600dpi
Press START Key to continue
Press
to Start TX
Auto
PDF
Auto
600dpi
100%
•
To continue scanning, set the next original, change the settings as needed, and press the Start
key.
•
Press the Enter (OK) key when you want to complete scanning originals.
•
When you want to cancel all scanned copies, press the Stop/Clear key. Screen will return to
the scan setting screen of Step 1.
3-7
Performing the Required Operation at the Scanner
3-8
MEMO
E1
First edition 2009.3
Printed in China 303JR56010