4-139-836-45(1)
WARNING
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or
moisture.
To reduce the risk of fire, do not cover the
ventilation of the apparatus with newspapers,
tablecloths, curtains, etc. And do not place lighted
candles on the apparatus.
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing,
and do not place objects filled with liquids, such
as vases, on the apparatus.
FM/AM
Clock Radio
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or
batteries installed) to excessive heat such as
sunshine, fire or the like for a long time.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main plug
from the AC outlet immediately.
CAUTION
Operating Instructions
ICF-C7iP
Dream Machine is a trademark of Sony Corporation.
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
Notice for customers: the following
information is only applicable to equipment
sold in countries applying EU directives
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan, Minato-ku, Tokyo,
108-0075 Japan. The Authorized Representative
for EMC and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters,
please refer to the addresses given in separate
service or guarantee documents.
Features
No Power No Problem is a trademark of Sony Corporation.
©2009 Sony Corporation
Printed in China
Wake or sleep to iPod/Radio
Dual Alarm
FM/AM 2-band digital synthesized tuner
30 Station Presets (20 FM. 10 AM)
Brightness Control (High/Mid/Low)
Extendable Snooze system from 10 to 60 min
No Power No Problem alarm system to keep
the clock and the alarm operating during a
power interruption with a CR2032 battery
installed
Precautions
Operate the unit on the power source specified
in “Specifications.”
To disconnect the AC power cord (mains lead),
pull it out by the plug, not the cord.
The unit is not disconnected from the AC
power source (mains) as long as it is connected
to the wall outlet, even if the unit itself has been
turned off.
Since a strong magnet is used for the speaker,
keep personal credit cards using magnetic coding
or spring-wound watches away from the unit to
prevent possible damage from the magnet.
Do not leave the unit in a location near a heat
source such as a radiator or airduct, or in a
place subject to direct sunlight, excessive dust,
mechanical vibration, or shock.
Allow adequate air circulation to prevent
internal heat build-up. Do not place the unit on
a surface (a rug, a blanket, etc.) or near
materials (a curtain) which might block the
ventilation holes.
Should any solid object or liquid fall into the unit,
unplug the unit and have it checked by qualified
personnel before operating it any further.
To clean the casing, use a soft cloth dampened
with a mild detergent solution.
Never touch the wire of the external FM aerial
during a thunderstorm. Furthermore,
immediately disconnect the AC power cord
from the radio.
NOTES ON LITHIUM BATTERY
Wipe the battery with a dry cloth to assure a
good contact.
Be sure to observe the correct polarity when
installing the battery.
Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
Disposal of Old Electrical &
Electronic Equipment (Applicable
in the European Union and other
European countries with separate
collection systems)
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling
of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you
will help prevent potential negative consequences
for the environment and human health, which
could otherwise be caused by inappropriate waste
handling of this product. The recycling of
materials will help to conserve natural resources.
For more detailed information about recycling of
this product, please contact your local Civic
Office, your household waste disposal service or
the shop where you purchased the product.
Disposal of waste batteries
(applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the battery or on the packaging
indicates that the battery provided with this
product shall not be treated as household waste.
On certain batteries this symbol might be used in
combination with a chemical symbol. The
chemical symbols for mercury (Hg) or lead (Pb)
are added if the battery contains more than
0.0005% mercury or 0.004% lead.
By ensuring these batteries are disposed of
correctly, you will help prevent potentially
negative consequences for the environment and
human health which could otherwise be caused
by inappropriate waste handling of the battery.
The recycling of the materials will help to
conserve natural resources.
In case of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery, this
battery should be replaced by qualified service
staff only.
To ensure that the battery will be treated properly,
hand over the product at end-of-life to the
applicable collection point for the recycling of
electrical and electronic equipment.
For all other batteries, please view the section on
how to remove the battery from the product
safely. Hand the battery over to the applicable
collection point for the recycling of waste
batteries.
For more detailed information about recycling of
this product or battery, please contact your local
Civic Office, your household waste disposal
service or the shop where you purchased the
product.
If you have any questions or problems concerning
your unit, please consult your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made
the following checks, consult your nearest Sony
dealer.
The clock flashes “0:00” due to a power
interruption.
The battery is low. Replace the battery. Remove
the old battery and install a new one.
The radio, iPod or buzzer alarm does not
sound at the preset alarm time.
Check that alarm “A” or alarm “B” is properly
displayed.
The radio or alarm of iPod is activated but no
sound comes on at the preset alarm time.
Check the alarm volume setting.
There is no sound from the iPod.
Make sure the iPod is securely connected.
Adjust the VOLUME.
The iPod cannot be operated with this unit.
Make sure the iPod is securely connected.
The iPod cannot be charged.
Make sure the iPod is securely connected.
When daylight saving time begins, the clock
does not employ the daylight saving time
automatically.
Make sure the clock is set correctly.
Press and hold CLOCK and SNOOZE/DATE/
SLEEP OFF simultaneously for at least
2 seconds to activate the Automatic DST
function.
Specifications
Connecting the aerial
Section for iPod
To connect the AM loop
aerial
DC out: 5V
MAX: 500mA
Radio section
Frequency range
Band
Frequency
Channel step
FM
87.5 MHz – 108 MHz
0.05 MHz
AM
531 kHz – 1 602 kHz
9 kHz
The shape and the length of the aerial is designed
to receive AM signals. Do not dismantle or roll up
the aerial.
1 Remove only the loop part from the
plastic stand.
2 Set up the AM loop aerial.
General
Speaker
Approx. 3.8 cm (1 1/2 inches) dia. 8 Ω
Input
AUDIO IN jack (ø 3.5 mm stereo minijack)
Power output
0.8 W (at 10% harmonic distortion)
Power requirements
230 V AC, 50 Hz
For clock back up: 3V DC, one CR2032 battery
Dimensions
Approx. 115 mm × 124.7 mm × 97.1 mm (w/h/d)
(4 9/16 inches × 4 15/16 inches × 3 7/8 inches) not
including projecting parts and controls
Mass
Approx. 520 g (1 lb 2.3 oz) including power
supply unit
Supplied accessories
Remote commander (1)
AM loop aerial (1)
Audio connecting cable (1)
Universal Dock Adapter for iPhone (1)
Universal Dock Adapter for iPhone 3GS & iPhone
3G (1)
Universal Dock Adapter for iPhone 4S & iPhone 4
(1)
Design and specifications are subject to change
without notice.
Compatible iPod/
iPhone models
Compatible iPod/iPhone models are as follows.
Update your iPod/iPhone to use the latest
software before you use it.
iPod touch (4th generation)
iPod touch (3rd generation)
iPod touch (2nd generation)
iPod touch (1st generation)
iPod nano (6th generation)*
iPod nano (5th generation)
iPod nano (4th generation)
iPod nano (3rd generation)
iPod nano (2nd generation)
iPod nano (1st generation)
iPod with video
iPod with color display
iPod with click wheel
iPod classic
iPod mini
iPhone 4S
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
* The iPod nano (6th generation) cannot be
controlled by the remote when the command of
“MENU,” “,” “,” and “ENTER” is pressed.
Notes
In these Operating Instructions, “iPod” is used
as a general reference to functions of iPod on an
iPod or iPhone, unless otherwise specified by
the text or illustrations.
The connector of the unit is for sole use with an
iPod. If you use devices that do not match with
the connector, connect to the AUDIO IN
terminal of this unit with the supplied audio
connecting cable.
Sony cannot accept responsibility in the event
that data recorded to an iPod is lost or damaged
when using an iPod connected to this unit.
3 Connect the cords to the AM aerial
terminals.
Cord (A) or cord (B) can be connected to
either terminal.
Insert the cord while
pushing down the
terminal clamp.
Only insert up
to here.
A
B
About the backup
battery
To keep accurate time, this unit contains a
CR2032 battery inside of the unit as a backup
power source.
The battery keeps the clock operating in the event
of a power interruption.
Note for customers in Europe
The clock is preset at the factory, and its memory
is powered by the preinstalled Sony CR2032
battery. If the “0:00” appears in the display when
the unit is connected to AC outlet for the first
time, the battery may be weak. In this case,
consult a Sony dealer. The preinstalled CR2032
battery is considered part of the product, and is
covered by the warranty.
You are required to show “Note for customers in
Europe” (in this instruction) to a Sony dealer in
order to validate the warranty for this product.
Knowing when to replace the
battery
When the battery becomes weak, “” appears in
the display.
If a power interruption occurs while the battery is
weak, the current time and alarm will be erased.
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may cause a fire or
explosion.
Replacing the battery
1 Keep the AC plug connected to the AC
4 Make sure the AM loop aerial is
connected firmly by pulling softly.
Adjusting the AM loop aerial
Find a place and an orientation that provide good
reception.
Do not place the AM loop aerial near the unit
or other AV equipment, as noise may result.
Tip
Adjust the direction of the AM loop aerial for best
AM broadcast sound.
Preparing the remote
commander
Before using the card remote commander for the
first time, remove the insulation film.
outlet, remove the screw that secures the
battery holder at the bottom of the unit
using a screwdriver, and remove the
battery holder.
2 Replace a new battery in the battery holder
with the  side facing up.
3 Insert the battery holder back into the
unit and secure it with the screw.
4 Press iPod&iPhone, RADIO BAND,
AUDIO IN or SNOOZE/DATE/SLEEP
OFF to turn “” off in the display.
Note
When you replace the battery, do not disconnect
the plug from the AC outlet. Otherwise, the
calendar, current time, alarm and station presets
will be erased.

When to replace the battery
With normal use, the battery (CR2025) should
last for about six months. When the remote
commander no longer operates the unit, replace
the battery with a new one.

CR2032

CR2025

Notes
Do not attempt to charge the battery.
If you are not going to use the remote
commander for a long time, remove the battery
to avoid any damage that may be caused by
leakage and corrosion.
If the time in the display is
incorrect after the battery is
changed (Reset)
Press the Reset button with a pointed device. The
Reset button is in the small hole located near the
battery holder.
Area number 1:
Daylight saving time (summer time) begins at:
2:00 AM on the final Sunday of March.
Standard time begins at: 3:00 AM on the final
Sunday of October.
Area number 2:
Daylight saving time (summer time) begins at:
3:00 AM on the final Sunday of March.
Standard time begins at: 4:00 AM on the final
Sunday of October.
To cancel Automatic DST/Summer Time
adjustment during the daylight saving
time (summer time) period
FM wire aerial
AC power cord
The Automatic DST/Summer Time adjustment
can be canceled.
Press and hold CLOCK and SNOOZE/DATE/
SLEEP OFF at the same time at least 2 seconds
while the clock is displayed.
“ ” and “OFF” appear in the display to show that
Automatic DST/Summer Time adjustment has
been canceled. The display returns to the clock.
Notes
The change timing of Automatic DST/Summer
Time adjustment employed by the unit (see
above) is subjected to variation by
circumstances and the law in each country/
region. In such a case, cancel the Automatic
DST/Summer Time adjustment and set the
DST display manually as necessary. Customers
living in a country/region that do not use
daylight saving time (summer time) must
cancel Automatic DST/Summer Time
adjustment before using the unit.
To activate Automatic DST/Summer Time
adjustment again, press and hold CLOCK and
SNOOZE/DATE/SLEEP OFF at the same time
at least 2 seconds.
“ ” and “On” appear in the display to show
that Automatic DST/Summer Time adjustment
has been activated. The display returns to the
clock.
Tuning in to a station
The unit automatically scan AM or FM stations.
1 Press RADIO BAND to turn on the radio
to select the AM or FM band.
2 Press and hold TUNING + or –.
+ : scans upward through the frequency
bands.
– : scans downwards through the frequency
bands.
Scanning starts from the currently-tuned
frequency. When a station is received,
scanning stops.
3 Adjust the volume using VOLUME +
or –.
–Preset tuning
Operating an iPod
You can enjoy audio from iPod by connecting to
this unit. To use an iPod, refer to the user’s guide
of your iPod.
If you are using an iPhone 4S, iPhone 4, iPhone
3GS, iPhone 3G or iPhone, attach the supplied
universal dock adapter for iPhone 4S, iPhone 4,
iPhone 3GS, iPhone 3G or iPhone before
connecting.
The adapter number, ,  or , is shown on
the underside of the supplied universal dock
adapters.  is for the iPhone,  is for the iPhone
3GS & iPhone 3G and  is for the iPhone 4S &
iPhone 4. Check the adapter number before use.
Universal dock adapter
You can preset 20 stations for FM and 10 stations
for AM.
Presetting a station
1 Follow steps 1 and 2 in “Manual tuning”
to tune the frequency you wish to preset.
2 Press and hold DISPLAY/MEMORY for
at least 2 seconds.
3 Press PRESET + or – to select the preset
number, then press DISPLAY/MEMORY.
The frequency is stored with the selected
preset number.
Example: The following display appears
when you preset FM 105.8 MHz to preset
number 1 for FM.



Notes
When inserting an iPod into the unit, be sure to
use the universal dock adapter supplied with
your iPod or commercially available from
Apple Inc.
The connector of the unit is exclusively for use
with an iPod. If you use a device that does not
match the connector, connect it to the AUDIO
IN terminal of this unit with the supplied audio
connecting cable.
Sony cannot accept responsibility in the event
that data recorded on an iPod is lost or
damaged when using an iPod connected to this
unit.
For details of environmental conditions for
operating your iPod, check the website of Apple
Inc.
1 Press PUSH OPEN.
The Docking Tray is ejected halfway.

Setting the clock manually
1 Plug in the unit.
2 Press and hold CLOCK for at least 2
seconds.
The iPod & iPhone  and VOLUME + buttons have a tactile dot.
The year starts to flash in the display.
3 Press ALARM TIME SET + or –
repeatedly to set the year.
4 Press CLOCK.
5 Repeat steps 3 and 4 to set the month,
day, hour and minute, and then press
CLOCK.
The seconds start incrementing from zero.
Notes
If you do not press any button for about
1 minute while setting the clock, the clock
setting will be canceled.
A calendar is installed in this unit. When the
date is set, the day of the week is automatically
displayed.
SUN = Sunday, MON = Monday,
TUE = Tuesday, WED = Wednesday,
THU = Thursday, FRI = Friday, SAT = Saturday
The  and VOL + buttons have a
tactile dot.
Setting the clock for
the first time
This unit is preset to the current date and time at
the factory, and is powered by the backup battery.
All you need to do the first time is just plug it in
and select your time zone.
1 Plug in the unit.
The current CET (Central European Time)
appears in the display.
2 Press and hold BRIGHTNESS/ TIME
ZONE for at least 2 seconds.
Area number “1” flashes in the display.
3 Press ALARM TIME SET + or –
repeatedly to select the number as
follows:
Area number
Time zone
1 (default
setting)
Central European Time/
Central European
Summer Time
2
Eastern European Time/
Eastern European
Summer Time
0
Western European Time/
Western European
Summer Time
4 Press BRIGHTNESS/ TIME ZONE to set.
Note
Though the clock is correctly set at the factory,
discrepancies may arise during transport or
storage. If necessary, set the clock to the correct
time by referring to “Setting the clock manually.”
When daylight saving time
(summer time) begins
This model automatically adjusts for daylight
saving time (summer time).
“ ” is displayed from the beginning of daylight
saving time (summer time) and disappears at the
end of daylight saving time (summer time)
automatically.
Automatic DST/summer time adjustment is based
on GMT (Greenwich Mean Time).
Area number 0:
Daylight saving time (summer time) begins at:
1:00 AM on the final Sunday of March.
Standard time begins at: 2:00 AM on the final
Sunday of October.
To display the year and date
Press SNOOZE/DATE/SLEEP OFF once for the
date, and press it again for the year.
After a while, the display will change back to the
current time automatically.
Setting the brightness
of the display
Three levels of brightness are available by pres­­­sing
BRIGHTNESS/ TIME ZONE.
Operating the radio
–Manual tuning
1 Press RADIO BAND to turn on the radio
and select the AM or FM band.
2 Press TUNING + or – to tune in to a
desired frequency.
3 Adjust the volume using VOLUME + or
–.
Note
The FM frequency display is raised or
lowered by a step of 0.1 MHz. For example,
frequency 88.00 and 88.05 MHz is displayed
as “88.0 MHz.”
The display shows the frequency for about
10 seconds, and then returns to the current
time.
To preset another station, repeat these steps.
–Auto preset tuning
1 Press RADIO BAND to turn on the radio
and select the AM or FM band.
2 Press and hold RADIO BAND until “AP”
appears in the display.
3 Press DISPLAY/MEMORY.
The unit automatically presets the available
channels in order.
Improving the reception
FM:
Extend the FM wire aerial fully to increase
reception sensitivity.
AM:
Connect the supplied AM loop aerial to the
unit. Rotate the aerial horizontally for optimum
reception.
Notes on radio reception
Keep digital music players or mobile phones
away from the AM loop aerial or the FM aerial,
as this may lead to reception interference.
When you are listening to the radio with an
iPhone connected to the unit, interference with
radio reception may occur.
When you are listening to the radio while
charging an iPod, interference with radio
reception may occur.
Even if the alarm setting for iPod is complete, if
you turn the power of iPod touch/iPhone off
before inserting the iPod touch/iPhone into the
unit, the alarm for iPod will not work.
To use the unit as a battery charger
5 Press ALARM TIME SET + or – to select
You can use the unit as a battery charger.
Charging begins when the iPod is connected to
the unit.
Charging status appears in the display of iPod. For
details, see the user’s guide of your iPod.
On copyrights
iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
“Made for iPod,” and “Made for iPhone” mean
that an electronic accessory has been designed to
connect specifically to iPod or iPhone,
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and
regulatory standards. Please note that the use of
this accessory with iPod or iPhone may affect
wireless performance.
Setting the alarm
2 Pull the Docking Tray all the way out.
“WAKE UP” appears and the hour flashes in
the display.
2 Press ALARM TIME SET + or –
3 Press ALARM TIME SET A or B.
The minute flashes.
4 Repeat step 2 to set the minute.
5 Press ALARM TIME SET A or B.
The iPod begins to play automatically.
You can operate the connected iPod by this
unit or the buttons on iPod.
6 Adjust the volume using VOLUME + or
–.
To
Turn off the iPod
Pause playback
Press
OFF, or press and
hold iPod &
iPhone 
iPod & iPhone

To resume play,
press it again.
Go to the next track

Go back to the previous
track
Locate a point while
listening to the sound
*
Locate a point while
observing the display
Go back to the previous
menu
Select a menu item or a
track for playback
Execute the selected menu
or begin playback
 (forward) or
 (backward)
while playing and
hold it until you
find the point.
 (forward) or
 (backward)
in pause and hold
it until you find
the point.
MENU**
/**
ENTER**
1 Press SLEEP while the unit is turned on.
alarm.”
2 Press ALARM TIME SET A or B to select
“RADIO” alarm mode.
“VOL” appears in the display.
3 Press ALARM TIME SET + or – to adjust
the volume.
4 Press ALARM TIME SET A or B.
Band (“FM” or “AM”) or “– –” flashes.
“– –” is the last station received.
the desired band or “– –”.
If you select “– –”, jump to step 8.
6 Press ALARM TIME SET A or B.
The preset number flashes.
7 Press ALARM TIME SET + or – to select
the desired preset number.
The setting is entered.
8 If “A” or “B” does not appear in the
display, press ALARM TIME SET A or B
again.
The days of the week flash.
6 Repeat step 2 to set the days of the week.
You can select the days from the following
three options:
Every day: SUN MON TUE WED THU FRI
SAT
Week day: MON TUE WED THU FRI
Week end: SUN SAT
7 Press ALARM TIME SET A or B.
The alarm mode setting is entered.
8 Press ALARM TIME SET + or –
repeatedly until the desired alarm mode
flashes.
You can choose one of 3 settings: “iPod”,
“RADIO” or “BUZZER.” Set the alarm mode
as follows:
– iPod: see “ Setting the alarm for iPod.”
– RADIO: see “ Setting the radio alarm.”
– BUZZER: see “ Setting the buzzer alarm.”
 Setting the alarm for iPod
1 Perform steps 1 to 8 in “To set the
alarm.”
2 Press ALARM TIME SET A or B to select
alarm mode for “iPod”.
“VOL” appears in the display.
3 Press ALARM TIME SET + or – to adjust
the volume.
4 Press ALARM TIME SET A or B.
The setting is entered.
5 If “A” or “B” does not appear in the
display, press ALARM TIME SET A or B
again.
The iPod will sound at the set time.
When using an iPod touch/iPhone
To wake up to music stored in an iPod touch/
iPhone, connect the iPod touch/iPhone to the
unit first, follow the steps above to set alarm
time, and then select the music function.
“SLEEP” appears and the sleep time flashes in
the display.
2 Press SLEEP to set the sleep timer
duration.
Each time you press SLEEP, the duration (in
minutes) changes as follows:
90
60
30
15
OFF
The display returns to clock mode for about
4 seconds after you have finished the duration
setting and released SLEEP, and then the sleep
timer starts.
The unit will play for the duration you set, and
then shut off.
To turn off the unit before the preset
time
Press SNOOZE/DATE/SLEEP OFF or OFF/
ALARM RESET.
To change the sleep timer setting
 Setting the Buzzer Alarm
You can press SLEEP repeatedly to select the
desired sleep timer setting even after the sleep
timer has been activated.
1 Perform steps 1 to 8 in “To set the
To deactivate the sleep timer
The radio will turn on at the set time.
alarm.”
2 Press ALARM TIME SET A or B to select
“BUZZER” alarm mode.
The setting is entered.
3 If “A” or “B” does not appear in the
display, press ALARM TIME SET A or B
again.
To confirm an alarm time setting
To cycle the hour rapidly, press and hold
ALARM TIME SET + or –.
connector of the unit.
5 Press iPod & iPhone .
1 Perform steps 1 to 8 in “To set the
To set the alarm
repeatedly until the desired hour appears.
3 Attach the adapter for your iPod/iPhone.
4 Insert your iPod/iPhone into the
 Setting the radio alarm
The buzzer will sound at the set time.
Note
The volume cannot be set for the buzzer alarm.
B for at least 2 seconds.
Setting the sleep timer
You can fall asleep to the music, etc., using the
built-in sleep timer that turns off the unit
automatically after a preset duration.
This clock radio is equipped with 3 alarm
modes—iPod, radio and buzzer. Before setting the
alarm, make sure to set the clock (see “Setting the
clock for the first time”).
1 Press and hold ALARM TIME SET A or
Note
If you try to store another station with the same
preset number, the previously stored station will
be replaced.
Tuning in to a preset station
1 Press RADIO BAND to turn on the radio
and select the AM or FM band.
2 Press PRESET + or – to select the desired
preset number.
3 Adjust the volume using VOLUME + or
–.
* During playback, this operation goes back to
the beginning of the current track. To go back
to the previous track, press twice.
**These operations are available only when using
the supplied remote commander.
Notes
When placing or removing the iPod, hold the
iPod at the same angle as that of the connector
on this unit, and do not twist or bend the iPod
as connector damage may result.
Do not carry the unit with an iPod set on the
connector. Doing so may cause a malfunction.
When placing or removing the iPod, hold the
Docking Tray securely with one hand and take
care not to press the controls of the iPod by
mistake.
Before disconnecting the iPod, pause playback.
Press ALARM TIME SET + or –. The setting will
be displayed for about 4 seconds.
Press SLEEP repeatedly to set the sleep timer to
“OFF” in step 2.
Connecting external
equipment
To listen to sound
1 Connect the AUDIO IN jack of the unit
to the line out jack or headphone jack of
the external equipment using the audio
connecting cable (supplied).
To change an alarm setting
Press and hold ALARM TIME SET + for at least
2 seconds to move the alarm time forwards. Press
and hold ALARM TIME SET – for at least
2 seconds to move the alarm time back.
When you release the button, the changed time
will be displayed for about 2 seconds. To change
the alarm time again, press ALARM TIME SET +
or – within these 2 seconds, otherwise the setting
change will be fixed as displayed.
To doze for a few more minutes
Press SNOOZE/DATE/SLEEP OFF.
The sound turns off but will automatically come
on again after about 10 minutes.
You can change the snooze time by pressing
SNOOZE/DATE/SLEEP OFF repeatedly within
4 seconds.
The maximum length of the snooze time is
60 minutes.
To stop the alarm
Press OFF/ALARM RESET to turn off the alarm.
The alarm will sound again at the same time the
next day.
To deactivate the alarm
Press ALARM TIME SET A or B to turn off the
ALARM A or B indicator from the display.
Note on the alarm in the event of a power
interruption
In the event of a power interruption, the alarm
will work until the battery is totally discharged.
However, certain functions will be affected as
follows:
The backlight will not light up.
If the alarm mode is set to iPod or radio, it will
change to BUZZER automatically.
If a power interruption occurs while the alarm
is sounding, the alarm will stop.
If OFF/ALARM RESET is not pressed, the alarm
will sound for about 5 minutes.
If “” appears in the display, the alarm will not
sound in the event of power interruption.
Replace the battery if “” appears.
The snooze function will not work.
During a power interruption, the alarm will
sound at the set time only once.
Audio connecting cable
(supplied)
To external
equipment
2 Press AUDIO IN to display “AUDIO IN.”
3 Play the equipment connected to the
AUDIO IN jack.
4 Adjust the volume using VOLUME + or –.
To return to the radio
Press RADIO BAND.
The frequency is shown in the display.
To return to the iPod
Press iPod & iPhone .
To stop listening
Press OFF, and stop playback on the connected
unit.
Notes
Refer also to the connected equipment’s manual.
The supplied audio connecting cable may not
be used with some external equipment. In this
case, use a cord suitable for the external
equipment you are using.
When you listen to the radio with external
equipment connected, turn off the connected
equipment to prevent noise. If noise occurs,
even when the equipment is turned off,
disconnect and place the external equipment
away from the unit.