®
Wireless Local Area Network Adapter
WL-130N
(For 802.11n draft, 802.11g & 802.11b Networks)
R
User Manual
E3123/ April 2007
WL-130N_manual.indd 1
4/10/07 12:29:30 PM
Copyright Information
No part of this manual, including the products and software described in it,
may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language in any form or by any means, except
documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN
NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES
OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR
LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA,
INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING
FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Product warranty or service will not be extended if: (1) the product is repaired,
modified or altered, unless such repair, modification of alteration is authorized
in writing by ASUS; or (2) the serial number of the product is defaced or
missing.
Products and corporate names appearing in this manual may or may not be
registered trademarks or copyrights of their respective companies, and are
used only for identification or explanation and to the owners’ benefit, without
intent to infringe.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL
ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT
TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT
BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES
THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND
SOFTWARE DESCRIBED IN IT.
Copyright © 2007 ASUSTeK COMPUTER INC. All Rights Reserved.
WL-130N_manual.indd 2
ASUS WLAN Adapter
4/10/07 12:29:32 PM
Contact Information
ASUSTeK COMPUTER INC.
Company address:
General (tel):
Web site address:
General (fax):
General email:
15 Li-Te Road, Beitou, Taipei 11259
+886-2-2894-3447
www.asus.com.tw
+886-2-2894-7798
info@asus.com.tw
Technical support
General support (tel):+886-2-2894-3447
Online support:
http://support.asus.com
ASUS COMPUTER INTERNATIONAL (America)
Company address:
General (fax):
Web site address:
44370 Nobel Drive, Fremont, CA 94538, USA
+1-510-608-4555
usa.asus.com
Technical support
General support (tel):+1-502-995-0883
Online support:
http://support.asus.com
Notebook (tel):
+1-510-739-3777 x5110
Support (fax):
+1-502-933-8713
ASUS COMPUTER GmbH (Germany & Austria)
Company address:
General (tel):
Web site address:
General (fax):
Online contact:
Harkort Str. 25, D-40880 Ratingen, Germany
+49-2102-95990
www.asus.com.de
+49-2102-959911
www.asus.com.de/sales
Technical support
Component support: +49-2102-95990
Online support:
http://support.asus.com
Notebook support: +49-2102-959910
Support (fax):
+49-2102-959911
ASUS WLAN Adapter
WL-130N_manual.indd 3
4/10/07 12:29:32 PM
Table of Contents
1. Introduction...............................................................................5
Package contents...................................................................................5
Features..................................................................................................5
2. Installation.................................................................................6
System Requirements............................................................................6
Installation Procedures...........................................................................6
Installing ASUS WLAN utilities and driver.................................................6
Reading the WLAN Status Indicators........................................................7
ASUS One Touch Wizard..........................................................................8
Configuring with ASUS WLAN Settings utility (Infrastructure)...................9
Configuring with ASUS WLAN Settings utility (Ad Hoc)..........................10
3. Software Reference.................................................................11
ASUS WLAN Control Center................................................................11
ASUS Wireless Settings Utility.............................................................13
Status - Status.........................................................................................13
Status - Connection.................................................................................15
Status - IP Config....................................................................................16
Status - Ping............................................................................................16
Config - Basic..........................................................................................17
Config - Advanced...................................................................................18
Config - Encryption..................................................................................19
Config - Authentication............................................................................22
Survey - Site Survey................................................................................22
About - Version Info.................................................................................23
Link State................................................................................................24
Exit Wireless Settings..............................................................................24
Windows® XP/2003 Wireless Options...................................................25
4. Troubleshooting......................................................................27
5. Glossary...................................................................................29
6. Appendix..................................................................................37
WL-130N_manual.indd 4
ASUS WLAN Adapter
4/10/07 12:29:33 PM
Chapter 1 - Introduction
Chapter 1
Introduction
Package contents
Check the following items in your ASUS Wireless LAN Adapter package.
Contact your retailer if any item is damaged or missing.
1 x ASUS Wireless LAN Adapter (WL-130N)
1 x Extension Cable Antenna
1 x Support CD
1 x Quick Start Guide
Features
Draft 802.11n compliant, full compatible with 802.11b/g
Suitable for seamless multimedia stream
Supports WEP, WPA and WPA2 for enhanced security
Windows® Vista OS support
ASUS WLAN Adapter
WL-130N_manual.indd 5
4/10/07 12:29:33 PM
Chapter 2 - Installation
2. Installation
System Requirements
Chapter 2
Installation
To begin using the WLAN Adapter, you must meet the following minimum
requirements:
• Windows® XP/2000/2003/Vista (only driver support)
• PCI slot for personal computer
• 128MB system memory or larger
• 750MHz processor or higher
Important: Install the WLAN Adapter utilities before inserting the WLAN
Adapter into your computer.
Installing ASUS WLAN utilities and driver
NOTE: The ASUS WLAN utilities is only for Windows® 2000/2003/XP.
Follow these instructions to install the WLAN Adapter utilities and driver. Insert
the support CD into your optical drive. If autorun is enabled in your computer,
the CD auto�������������������������������������������
matically displays the utility menu. Click Install ASUS WLAN Card
Utilities/Driver. If autorun is disabled, double-click SETUP.EXE in the root
directory of the CD.
1.Select your language and click Install
ASUS WLAN Card Utilities/Driver.
2.Click Next on the Welcome screen.
3.Click Next to use the default Destination
Folder or click Browse to select another folder.
4.Click Next to create short cut.
WL-130N_manual.indd 6
ASUS WLAN Adapter
4/10/07 12:29:37 PM
5. The installation process takes several
seconds.
6. When Setup is complete, click Finish to
exit the installation wizard and restart the
computer.
7. Carefully insert the WLAN Adapter into
your computer’s PCI slot. Windows will
automatically detect and configure the
WLAN Adapter using the utilities and
drivers installed in the previous steps.
8. Windows XP/2003 users: When the
program is launched for the first time
(during Windows restart), you are asked
to choose one utility to configure the
WLAN Adapter. Select "Only use our
WLAN utilities and disable Windows
wireless function".
Chapter 2
Installation
Chapter 2 - Installation
Reading the WLAN status indicator
The device comes with one LED that indicates the status of the WLAN
Adapter.
ACT LED
Blinking: Transmitting data; the blinking
speed indicates the link speed.
ACT LED
Radio off or Adapter is disabled.
OFF:
ASUS WLAN Adapter
WL-130N_manual.indd 7
4/10/07 12:29:40 PM
Chapter 2 - Installation
ASUS One Touch Wizard
Use ASUS One Touch Wizard to setup your wireless connection with an
existing wireless LAN.
Chapter 2
Installation
1.Launch ASUS One Touch Wizard from
Start menu and click Next to set up your
wireless network.
2.Select an AP from the Available Networks
field, then click Next.
3.Connection is complete. Click Next
to setup the IP address for the WLAN
Adapter.
4.Choose to obtain an IP address or to
assign static address manually for your
WLAN Adapter. When IP setting is
complete, click Finish to exit ASUS One
Touch Wizard.
Note: If the access point you want to connect has set up encryption
policies, you must configure the same encryption on your WLAN Adapter.
Select "Configure your wireless LAN settings" radio button in step 2
and make the settings accordingly. When the encryption settings are
complete, you can launch ASUS One Touch Wizard once again from the
Start menu to set up the connection with your AP.
We suggest WL-130N work with WL-500W Super Speed N wireless router
for maximum performance. Make sure the router firmware is the updated.
Check ASUS website for router latest updated firmware.
WL-130N_manual.indd 8
ASUS WLAN Adapter
4/10/07 12:29:43 PM
Chapter 2 - Installation
Configuring with ASUS WLAN Settings utility
(Infrastructure)
Chapter 2
Installation
Use ASUS WLAN Settings utility to get connected with an existing wireless
network.
1.Right-click the wireless connection icon
and select Wireless Settings.
2. Check the Config page to set the SSID
(network name) to that of your wireless AP.
3.Use Site Survey if you don’t know the
SSID of your access point(s).
4. Encryption settings must match those
at the access point. Ask your network
administrator about settings if necessary.
Click Apply to activate the settings.
5.Check the Status page to see the
association state. If connection is
established, the box shows “Connected xx:xx:xx:xx:xx:xx”.
6.Check the Connection tab to see the
signal strength. Click OK to exit the utility.
ASUS WLAN Adapter
WL-130N_manual.indd 9
4/10/07 12:29:47 PM
Chapter 2 - Installation
Configuring with ASUS WLAN Settings utility
(Ad Hoc)
The WLAN Adapter supports Ad Hoc mode which allows communication
Chapter 2
Installation
1.Right-click the wireless connection icon
and select Wireless Settings.
2.Click the Config button and set the WLAN
Adapter to Ad Hoc connection mode.
3.Click the Survey button to scan for Ad
Hoc nodes. Select the node you want to
communicate with and press Connect.
4.If the encryption settings of your WLAN
Adapter are different from those of the
other Ad Hoc nodes, you are prompted
to make the encryption of the two nodes
identical. Click Apply to activate the
settings.
5.Check the Status page to see the association
state. If connection is established, the box
shows “Connected - xx:xx:xx:xx:xx:xx”.
6.Check the Connection tab to see the
signal strength. Click OK to exit the utility.
10
WL-130N_manual.indd 10
ASUS WLAN Adapter
4/10/07 12:29:49 PM
Chapter 3 - Software Reference
3. Software Reference
ASUS WLAN Control Center
ASUS WLAN Control Center is an application which makes it easier to launch
WLAN applications and activate network location settings. The WLAN Control
Center starts automatically when system boots. When WLAN Control Center is
running, you can see a Control Center icon on the Windows taskbar.
Starting the Control Center
• Select ASUS WLAN Control Center in Windows Start
menu, or
• Double-click the ASUS WLAN Control Center icon on the desktop.
Chapter 3
Software Reference
Using the Control Center
The Control Center taskbar icon displays the following information:
• Link quality of the WLAN Adapter (Excellent, Good, Fair, Poor, Not
Linked)
• Whether the WLAN Adapter is connected to a network (Blue:
Connected, Gray: Not Connected)
Taskbar Icon and Status
Wireless Status Icons (on the taskbar)
Excellent link quality and connected to Internet (Infrastructure)
Good link quality and connected to Internet (Infrastructure)
Fair link quality and connected to Internet (Infrastructure)
Poor link quality and connected to Internet (Infrastructure)
Excellent link quality but not connected to Internet (Infrastructure)
Good link quality but not connected to Internet (Infrastructure)
Fair link quality but not connected to Internet (Infrastructure)
Poor link quality but not connected to Internet (Infrastructure)
Not linked and not connected to Internet (Infrastructure)
ASUS WLAN Adapter
WL-130N_manual.indd 11
11
4/10/07 12:29:51 PM
Chapter 3 - Software Reference
Taskbar icon - Right-click menu
Right-click the taskbar icon to show the following menu items:
Wireless Settings – Click to launch Wireless Settings application.
Activate Configuration – Click to choose a preset profile.
Mobile Manager – Click to launch Mobile Manager application.
Site Monitor – Click to launch the Site Monitor application.
Preferences – Click to customize the Control Center program. You can
create a Control Center shortcut on the desktop and decide whether to
start Control Center when system boots.
• About Control Center-Shows the version of Control Center.
• Exit – Click to close the Control Center program.
•
•
•
•
•
Chapter 3
Software Reference
Taskbar icon - Left-click menu
Left-click the taskbar icon to show the following
menu items:
• Wireless Radio On – Click to turn
the wireless radio ON.
• Wireless Radio Off – Click to turn
the wireless radio OFF.
Taskbar Left-Click Menu
• Search & Connect – Click to view
the properties of available access points.
• Wireless Option (Windows ® XP/2003) – C l i c k t o choose
Windows® Wireless Zero Configuration (WZC) service or ASUS utilities
to configure your WLAN Adapter.
Taskbar Icon - Launch Wireless Settings
Double-click the taskbar icon����������������������������������������������
to launch the ASUS Wireless Settings utility.
12
WL-130N_manual.indd 12
ASUS WLAN Adapter
4/10/07 12:29:52 PM
Chapter 3 - Software Reference
ASUS Wireless Settings Utility
ASUS Wireless Settings utility is an application for managing the WLAN
Adapter. Use Wireless Settings to view or modify the configuration settings, or to
monitor the operational status of your WLAN Adapter. When Wireless Settings
is launched, you can see the tabbed property sheets which categorize the
configuration options into groups.
Starting Wireless Settings
Chapter 3
Software Reference
• Open the Windows Control Panel, then double-click the ASUS WLAN
Adapter Settings icon.
or
• Click the Windows Start button, select Programs | ASUS Utility |
WLAN Adapter | Wireless Settings.
or
• Right-click the Control Center icon on the Windows taskbar and
select Wireless Settings.
NOTE: If you have more than one ASUS WLAN device installed on your
computer, you may see a device selection window when you launch the
“Wireless Settings” utility. Select the device you want when such situation
occurs.
Status - Status
You can view the information about the
WLAN Adapter from the Status menu.
The status fields are blank if the WLAN
Adapter is not installed. You can turn
off the WLAN Adapter by clicking the
“Disable Radio” button.
Association State
Displays the connection status as
follows:
Connected - The adapter is now associated with one wireless LAN device.
When operating in Infrastructure mode, this field shows the MAC address
of the access point with which the WLAN Adapter is communicating. When
operating in Ad Hoc mode, this field shows the virtual MAC address used by
computers participating in the Ad Hoc network.
ASUS WLAN Adapter
WL-130N_manual.indd 13
13
4/10/07 12:29:53 PM
Chapter 3 - Software Reference
Scanning... : The station is trying to authenticate and associate with an access
point or Ad Hoc node.
Disconnected: The WLAN Adapter is installed to the system, but not yet
connected to a wireless device.
SSID: Displays the Service Set Identifier (SSID) of the device that the adapter
is either associated or intending to join.
MAC address: Shows the hardware address of the WLAN Adapter. MAC
address is a unique identifier for networking devices (typically written as twelve
hexadecimal digits from 0 through 9 and A through F separated by colons, i.e.
00:E0:18:F0:05:C0).
Current Channel: Displays the radio channel to which the adapter
Chapter 3
Software Reference
is currently tuned. This number changes as the radio scans the available
channels. When data transmition is in processing, this number displays the
radio channel which the adapter is currently using.
Current Data Rate: Display the data rate that the adpter support. When
data transmition is in processing, this number displays the current data rate in
megabits per second (Mbps).
Radio State: Shows the wireless radio status: ON or OFF.
Radio On - When the wireless radio is turned ON, the icon on the right appears
in the upper left of the Status page.
Radio Off- When the wireless radio is turned OFF, the icon on the right
appears in the upper left of the Status page.
Buttons
Rescan – Make the WLAN Adapter rescan all available devices. If the
current link quality or signal strength is poor, rescanning can be used to
push the radio off a weak access point and search for a better link with another
access point. This function usually takes several seconds.
Change SSID – Click this button to set the SSID to that of the AP you want to
connect.
Search & Connect – Click this button to connect to an available wireless AP.
14
WL-130N_manual.indd 14
ASUS WLAN Adapter
4/10/07 12:29:54 PM
Chapter 3 - Software Reference
Save Configuration
When you make settings for a
certain working environment, you
may need to save your settings to a
profile so that you can easily switch
to the settings without repeating the
configurations. For example, you
can set profiles for work, home and
other situations. When you travel from home to work, choose the "office" profile
that contains all your settings for office use. When you travel back home,
choose the “home” profile.
Activate Configuration
Chapter 3
Software Reference
Auto roaming is enabled by default and
makes the adapter automatically switch to
APs of better signal. You can uncheck it if
you want to connect to a specified AP using
a particular profile.
Status - Connection
You can view the current link statistics about
the WLAN Adapter. These statistics are
updated once per second and are valid if the
WLAN Adapter is correctly installed.
Frame Sent/Received
Transmitted - The number of frames that
were transmitted.
Received - The number of frames that were received.
Frame Error
Transmitted - The number of frames that were not successfully transmitted.
Received - The number of frames that were not successfully received.
Connection Quality
Signal Strength - Shows the link quality of the access point or Ad Hoc node
the WLAN Adapter is currently connected to. Ratings are: Excellent, Good,
Fair, and Poor.
Overall Connection Quality
The overall connection quality is derived from the current signal strength. A
graphic chart uses percentage to show signal quality.
ASUS WLAN Adapter
WL-130N_manual.indd 15
15
4/10/07 12:29:56 PM
Chapter 3 - Software Reference
Status - IP Config
IP Config tab shows all the current
host and WLAN Adapter information
including Host Name, DNS Servers,
IP Address, Subnet Mask and Default
Gateway.
Button
IP Release - If you want to remove the
current IP address, click this button to
release the IP address from DHCP server.
Chapter 3
Software Reference
IP Renew - If you want to obtain a new IP address from DHCP server, click this
button to renew the IP address.
Ping - Click this button to open “Ping” tab which is used to ping the devices in
your network.
NOTE: The IP Release and IP Renew buttons can only be used on the
WLAN Adapter which gets IP address from DHCP server.
Status - Ping
Click the "Ping" button in Status-IP
Config tab to open this page. The Ping
tab allows you to verify the accessibility
of other computers or network devices.
To ping a connection:
1. Type the IP address of the device you
want to verify in the IP Address field.
2. C o n f i g u r e t h e p i n g s e s s i o n b y
assigning the ping packet size and
number of packet to send, and the timeout value (in milliseconds).
3. Click the “Ping” button.
During the ping session, the Ping button Changes into a Stop button. To cancel
the ping session, click the “Stop” button.
The session field displays information on the verified connection including the
roundtrip time (minimum, maximum, and average) and packets sent, received,
and lost after a ping session.
Click the “Clear” button to clear the session field.
16
WL-130N_manual.indd 16
ASUS WLAN Adapter
4/10/07 12:29:58 PM
Chapter 3 - Software Reference
Config - Basic
This page enables you to change the
WLAN Adapter configurations.
Network Type
Infrastructure – Infrastructure means
to establish a connection with an access
point. Once connected, the access
point allows you to access wireless
LAN and wired LAN (Ethernet). The
Channel field turns to Auto if the
connection is based on Infrastructure.
Chapter 3
Software Reference
Ad Hoc – Ad Hoc means to communicate directly with other wireless clients
without using an access point. An “Ad Hoc” network can be setup quickly
and easily without pre-planning, for example, sharing meeting notes between
attendants in a meeting room.
Network Name (SSID)
SSID stands for “Service Set Identifier”, which is a string used to identify a
wireless LAN. Use the SSID to connect with a known access point. You can
enter a new SSID or select one from the drop-down list box. If you get connected
by designating the SSID, you are only to connect the AP with the SSID you
assigned. If the AP is removed from the network, your WLAN Adapter does not
roam automatically to other APs. SSIDs must all be printable characters and
having a maximum of 32 case sensitive characters, such as “ Wireless”.
NOTE: Set the SSID to a null string, if you wish to allow your station to
connect to any access point it can find. But you cannot use null string in
Ad Hoc mode.
Channel
The Channel field is for setting radio channel. Your WLAN Adapter can
automatically select the correct channel to communicate with an wireless device,
and the parameter is fixed to "Auto" in both Infrastructure and Ad Hoc mode.
The available radio channels depend on the regulations in your country. For
the United States (FCC) and Canada (IC), channel 1 to 11 are supported. For
Europe (ETSI), channel 1 to 13 are supported.
Click Apply to save and activate the new configurations.
ASUS WLAN Adapter
WL-130N_manual.indd 17
17
4/10/07 12:29:59 PM
Chapter 3 - Software Reference
Encryption – Click this link to show the "Encryption" tab.
Advanced – Click this link to show the "Advanced" tab. In most cases, the
default values do not have to be changed.
Troubleshooting – Click on this to show the Troubleshooting utility.
Config - Advanced
Chapter 3
Software Reference
Click Advanced link on Config-Basic
page to show this tab. This tab allows
you to set up additional parameters for
the wireless Adapter. We recommend
using the default values for all items in
this window.
RTS Threshold (0-2347)
The RTS/CTS (Request to Send/Clear
to Send) function is used to minimize collisions among wireless stations.
When RTS/CTS is enabled, the router refrains from sending a data frame until
another RTS/CTS handshake is completed. Enable RTS/CTS by setting a
specific packet size threshold. The default value (2347) is recommended.
Fragmentation Threshold (256-2346)
Fragmentation is used to divide 802.11 frames into smaller pieces (fragments)
that are sent separately to the destination. Enable fragmentation by setting
a specific packet size threshold. If there is an excessive number of collisions
on the WLAN, experiment with different fragmentation values to increase the
reliability of frame transmissions. The default value (2000) is recommended for
normal use.
18
WL-130N_manual.indd 18
ASUS WLAN Adapter
4/10/07 12:30:00 PM
Chapter 3 - Software Reference
Config - Encryption
This page enables you to configure the Wireless LAN Adapter encryption
settings. For data confidentiality in a wireless environment, IEEE 802.11
specifies a Wired Equivalent Privacy (WEP) algorithm to offer transmission
privacy. The WEP uses keys to encrypt and decrypt data packets. The
encryption process can scramble frame bits to avoid disclosure to others. The
WPA/WPA2 is improved security system for 802.11 which are developed to
overcome the weakness of the WEP protocol.
Network Authentication
Chapter 3
Software Reference
Since there is no precise bound in
wireless LANs, the WLAN users need
to implement certain mechanism
to provide security solution. The
Authentication policies in this tab
provide protection of different levels
such as Open, Shared, WPA-Personal,
WPA2-Personal, WPA-Enterprise, and
WPA2-Enterprise.
Open - Select this option to make
the network operate on Open System mode, which use no authentication
algorithm. Open stations and APs can authenticate with each other without
checking any WEP Key, even if there is.
Shared - Select this option to make the network operate on Shared key mode.
In a Share Key Authentication system, four-step exchange of frames is required
to validate that the station is using the same WEP Key as the access point.
WPA-Personal/ WPA2-Personal - Select this option to enable WPA PreShared Key under Infrastructure mode. It enables communication between
your client and APs using WPA-Personal/WPA2-Personal encryption mode.
WPA-Enerprise/ WPA2-Enterprise - The network is operating in IEEE 802.1x
authentication mode. This mode is for environments with RADIUS (Remote
Access Dial-in User Service). In a RADIUS environment, three Extensible
Authentication Protocol (EAP) are supported, including PEAP, EPA/TLS, and
LEAP.
ASUS WLAN Adapter
WL-130N_manual.indd 19
19
4/10/07 12:30:01 PM
Chapter 3 - Software Reference
Data Encryption
For Open and Shared authentication mode, the configuration options of
encryption type are Disabled and WEP. For WPA-Enterprise, WPA-Personal,
WPA2-Enterprise and WPA2-Personal authentication mode, Temporal Key
Integrity Protocol (TKIP) encryption and Advanced Encryption Standard (AES)
encryption are supported.
Disabled - Disable the encryption function.
WEP - WEP Key is used to encrypt your data before it is transmitted over air.
You can only connect and communicate with wireless devices that use the
same WEP keys.
Chapter 3
Software Reference
TKIP - TKIP uses an encryption algorithm methods which is more stringent
than the WEP algorithm. It also uses existing WLAN calculation facilities to
perform encryption. TKIP verifies the security configuration after the encryption
keys are determined.
AES: AES is a symmetric 128-bits block encryption technique which works
simultaneously on multiple network layers.
Wireless Network Key
This option is enabled only if you select WPA-Personal or WPA2-Personal
authentication mode. Note: 8 to 63 characters or 64 hexadecimal are required
in this field.
Wireless Network Key (WEP)
This option is configurable only if you enable WEP in Network Authentication
field. The WEP Key is a 64-bits (5 byte) or 128-bits (13 byte) Hexadecimal
digits which is used to encrypt and decrypt data packets.
Key Format
You can select to enter Hexadecimal digits (0~9, a~f, and A~F) or ASCII
characters to setup keys by defining the Key Format.
Key Length
For 64 bits encryption, each key contains 10 hex digits or 5 ASCII characters.
For 128 bits encryption, each key contains 26 hex digits or 13 ASCII characters.
Two ways to assign WEP keys
1. Manual Assignment - When you select this option, the cursor appears
in the field for Key 1. For 64-bits encryption, you are required to enter four
WEP Keys. Each Key contains exactly 10 hex digits (0~9, a~f, and A~F).
For 128-bits encryption, you are required to enter four WEP Keys. Each
Key contains exactly 26 hex digits (0~9, a~f, and A~F).
20
WL-130N_manual.indd 20
ASUS WLAN Adapter
4/10/07 12:30:02 PM
Chapter 3 - Software Reference
2. Automatic Generation - Type a combination of up to 64 letters,
numbers, or symbols in the Passphrase box, the Wireless Settings Utility
automatically uses an algorithm to generate four WEP Keys.
Select one as your Default Key
The Default Key field allows you specify which of the four encryption keys is to
use for transmitting data over wireless LAN. You can change the default key
by clicking on the downward arrow, selecting the number of the key you want
to use, and clicking the “Apply” button. If the access point or station with which
you are communicating uses the identical key by the same sequence, you can
use any of the keys as the default on your WLAN Adapter.
Chapter 3
Software Reference
Click the “Apply” button after you have created the encryption keys, the
Wireless Settings Utility uses asterisks to mask your keys.
64/128bits versus 40/104bits
There are two levels of WEP Encryption: 64 bits and 128 bits.
Firstly, 64-bits WEP and 40-bits WEP are the same encryption method and
can interoperate in the wireless network. This lower level of WEP encryption
uses a 40-bits (10 Hex character) as a “secret key” (set by user), and a 24-bits
“Initialization Vector” (not under user control). This together makes 64 bits (40 +
24). Some vendors refer to this level of WEP as 40 bits and others refer to this
as 64 bits. Our Wireless LAN products use the term 64 bits when referring to
this lower level of encryption.
Secondly, 104-bits WEP and 128-bits WEP are the same encryption method
and can interoperate in the wireless network. This higher level of WEP
encryption uses a 104-bits (26 Hex character) as a “secret key” (set by user),
and a 24-bits “Initialization Vector” (not under user control). This together
makes 128 bits (104 + 24). Some vendors refer to this level of WEP as 104 bits
and others refer to this as 128 bits. Our Wireless LAN products use the term
128 bits when referring to this higher level of encryption.
ASUS WLAN Adapter
WL-130N_manual.indd 21
21
4/10/07 12:30:02 PM
Chapter 3 - Software Reference
Config - Authentication
This tab allows you to set the security settings to match those of your AP. It is
configurable only if you have set Network Authentication to WPA-Enterprise or
WPA2-Enterprise in Config-Encryption tab.
Authentication Type
The authentication type methods include:
Chapter 3
Software Reference
PEAP: PEAP (Protected Extensible
Authentication Protocol) authentication
is a version of Extensible Authentication
Protocol (EAP). EAP ensures mutual
authentication between a wireless client
and a server that resides at the network
operations center.
E PA / T L S : E PA / T L S ( E x t e n s i b l e
Authentication Protocol - Transport Layer Security) is a follow-on to Secure
Socket Layer (SSL). It provides strong security, but relies on client certificates
for user authentication.
LEAP: LEAP (Light Extensible Authentication Protocol) authentication is a
version of Extensible Authentication Protocol (EAP). EAP ensures mutual
authentication between a wireless client and a server that resides at the
network operations center.
Survey - Site Survey
Use the Site Survey tab to view statistics
on the wireless networks available to the
WLAN Adapter and their parameters.
• SSID: The SSID of the available
networks.
• Channel: The channel used by each
network.
22
WL-130N_manual.indd 22
ASUS WLAN Adapter
4/10/07 12:30:04 PM
Chapter 3 - Software Reference
• RSSI: The Received Signal Strength Indication (RSSI) transmitted by each
network. This information is helpful in determining which network to connect
to. The value is then normalized to a dBm value.
• Security: Wireless network encryption information. All devices in
the network should use the same encryption method to ensure the
communication.
• BSSID: The media access control (MAC) address of the access point or
the Basic Service Set ID of the Ad Hoc node.
NOTE: Some access points may disable SSID broadcast and hide
themselves from “Site Survey” or “Site Monitor”, however, you can
connect such AP if you know their SSID.
Chapter 3
Software Reference
Buttons
Search – To scan all available wireless networks and show the scan result in the
“Available Network” list.
Connect – To associate with a network, select the network from the
“Available Network” list and click this button.
About - Version Info
Use the Version Info tab to view program and WLAN Adapter version
information. The program version information field includes the Copyright and
utility version. The version information includes the Ndis version, Driver, Driver
Version and EEPROM Version.
This screen is an example only. Your version numbers
will be different from what are shown here.
ASUS WLAN Adapter
WL-130N_manual.indd 23
23
4/10/07 12:30:05 PM
Chapter 3 - Software Reference
Link State
WLAN Adapter “Link State” icon appears on the left side of
the WLAN Adapter Settings. Use the icon to view the current
signal status.
Excellent Link Quality (Infrastructure)
Good Link Quality (Infrastructure)
Fair Link Quality (Infrastructure)
Poor Link Quality (Infrastructure)
Not linked (Infrastructure)
Chapter 3
Software Reference
Exit Wireless Settings
To exit Wireless Settings, you can click OK or Cancel.
24
WL-130N_manual.indd 24
ASUS WLAN Adapter
4/10/07 12:30:07 PM
Chapter 3 - Software Reference
Windows® XP/2003 Wireless Options
The wireless options window shown below is only available for Windows®
XP/2003. It appears when you run the Control Center utility at the first time.
Select the utility you want to use for configuring your WLAN Adapter.
Only use Windows wireless function
– Only use Windows ® 2003/XP
Wireless Zero Configuration service to
configure the WLAN Adapter.
Only use our WLAN utilities and
disable wireless function
– Only use ASUS WLAN utilities to configure the WLAN Adapter.
(recommended)
Chapter 3
Software Reference
You can open the Wireless Option
setting window at any time by leftclicking the control center icon and
choosing Wireless Option.
Taskbar Left-Click Menu
Configuring with Windows XP SP2 Wireless Zero Configuration
service
®
If you want to configure your WLAN Adapter via Windows® XP/2003 Wireless
Zero Configuration (WZC) service, follow the instruction below to make the
settings.
1. Double-click the wireless network
icon on the task bar to view available
networks.Select the AP and click
Connect.
2. A window prompts out asking you for
the key if you have set up encryption
on your wireless router, input the keys
and click Connect. The connection is
complete.
ASUS WLAN Adapter
WL-130N_manual.indd 25
25
4/10/07 12:30:15 PM
Chapter 3 - Software Reference
To set up the wireless connection properties, right-click the wireless icon on the
taskbar and select Open Network Connection. Then right-click the network
connection icon and select Property to open the Wireless Network Connection
Status page.
Chapter 3
Software Reference
1.The General page shows status, duration,
speed, and signal strength. Signal
strength is represented by green bars with
5 bars indicating excellent signal and 1
bar meaning poor signal.
26
WL-130N_manual.indd 26
2.Select “Wireless Networks” tab to show
Preferred networks. Use the Add button
to add the “SSID” of available networks
and set the connection preference order
with the Move up and Move down
buttons. The radio tower with a signal
icon identifies the currently connected
access point. Click Properties to set the
authentication of the wireless connection.
ASUS WLAN Adapter
4/10/07 12:30:21 PM
Chapter 4 - Troubleshooting
4. Troubleshooting
The following troubleshooting guides provide answers to some of the more
common problems, which you may encounter while installing or using WLAN
Adapter products. If you encounter difficulties that are not mentioned in this
section, please contact the Wireless LAN Technical Support.
Verify if the WLAN Adapter is installed correctly.
When the WLAN Adapter setup is complete, you can verify if the driver has
been setup properly. Right click My Computer, select Properties, and click
the Device Manager tab. Then double-click the Network adapters icon;
you should see “802.11n Wireless LAN Card” with an icon of an expansion
adapter. There should not be a “!” or “?” (problem) or “x” (disabled) symbol over
this icon.
There is a yellow exclamation mark or a yellow question mark in
Device Manager in front of my WLAN Adapter.
To resolve the problem, you should update/reinstall the WLAN Adapter
driver. In “Device Manager”, right click 802.11n Wireless LAN Card, select
Properties, and select Driver tab. Click on Update Driver button, then follow
the “Update Device Driver Wizard” to complete the driver installation.
Chapter 4
Troubleshooting
Cannot connect to any access points
Follow the procedure below to configure your WLAN Adapter.
a. Verify that the “Network Type” is in “Infrastructure” mode.
b. Verify that the “SSID” of your WLAN Adapter is set to the same “SSID”
of an access point.
c. Verify that the “Encryption” type is the same as that of an access point.
If you enabled “WEP” encryption, you must also set the same WEP
Keys on both sides.
ASUS WLAN Adapter
WL-130N_manual.indd 27
27
4/10/07 12:30:21 PM
Chapter 4 - Troubleshooting
Cannot connect to a Station (WLAN Adapter)
Follow the procedure below to configure your WLAN Adapter.
a. Verify that the “Network Type” is in “Ad Hoc” mode.
b. Verify that the “SSID” of your WLAN Adapter is set to the same “SSID” of
the other station (or another WLAN Adapter).
c. Verify that the “Channel” of the WLAN Adapter is “Auto” or set to the
same “channel” of the other station (or another WLAN Adapter).
d. Verify that the “Encryption” type is the same as the other station (or another
WLAN Adapter). If “WEP” encryption is enabled, you must set the same
“WEP” Keys on both stations.
Bad link quality or bad signal strength
There are two possible reasons. First is radio interference, keep the
environment around the WLAN Adapter away from microwave ovens and large
metal objects. Then try to reorient the WLAN Adapter antenna. Second is the
distance, decrease the distance between your WLAN Adapter and the access
point or station (or another WLAN Adapter).
Chapter 4
Troubleshooting
28
WL-130N_manual.indd 28
ASUS WLAN Adapter
4/10/07 12:30:22 PM
Chapter 5 - Glossary
5. Glossary
Access Point (AP)
A networking device that seamlessly connects wired and wireless networks. access
points combined with a distributed system support the creation of multiple radio
cells that enable roaming throughout a facility.
Ad Hoc
A wireless network composed solely of stations within mutual communication range
of each other (no access point).
Basic Rate Set
This option allows you to specify the data transmission rate.
Basic Service Area (BSS)
A set of stations controlled by a single coordination function.
Broadband
A type of data transmission in which a single medium (such as cable) carries
several channels of data at once.
Channel
An instance of medium use for the purpose of passing protocol data units that
may be used simultaneously, in the same volume of space, with other instances
of medium use (on other channels) by other instances of the same physical layer,
with an acceptably low frame error ratio due to mutual interference.
Client
A client is the desktop or mobile PC that is connected to your network.
Chapter 5
Glossary
COFDM (for 802.11a or 802.11g)
Signal power alone is not enough to maintain 802.11b-like distances in an 802.11a/
g environment. To compensate, a new physical-layer encoding technology was
designed that departs from the traditional direct-sequence technology being
deployed today. This technology is called COFDM (coded OFDM). COFDM was
developed specifically for indoor wireless use and offers performance much
superior to that of spread-spectrum solutions. COFDM works by breaking one
high-speed data carrier into several lower-speed subcarriers, which are then
transmitted in parallel. Each high-speed carrier is 20 MHz wide and is broken
up into 52 subchannels, each approximately 300 KHz wide. COFDM uses 48 of
these subchannels for data, while the remaining four are used for error correction.
COFDM delivers higher data rates and a high degree of multipath reflection
recovery, thanks to its encoding scheme and error correction.
ASUS WLAN Adapter
WL-130N_manual.indd 29
29
4/10/07 12:30:23 PM
Chapter 5 - Glossary
Each subchannel in the COFDM implementation is about 300 KHz wide. At the low
end of the speed gradient, BPSK (binary phase shift keying) is used to encode 125
Kbps of data per channel, resulting in a 6,000-Kbps, or 6 Mbps, data rate. Using
quadrature phase shift keying, you can double the amount of data encoded to 250
Kbps per channel, yielding a 12-Mbps data rate. And by using 16-level quadrature
amplitude modulation encoding 4 bits per hertz, you can achieve a data rate of
24 Mbps. The 802.11a/g standard specifies that all 802.11a/g-compliant products
must support these basic data rates. The standard also lets the vendor extend the
modulation scheme beyond 24 Mbps. Remember, the more bits per cycle (hertz)
that are encoded, the more susceptible the signal will be to interference and fading,
and ultimately, the shorter the range, unless power output is increased.
Default Key
This option allows you to select the default WEP key. This option allows you to
use WEP keys without having to remember or write them down. The WEP keys
generated using the Pass Phrase is compatible with other WLAN products.
The Pass Phrase option is not as secure as manual assignment.
Device Name
Also known as DHCP client ID or network name. Sometimes provided by an
ISP when using DHCP to assign addresses.
DHCP (Dynamic Host Configuration Protocol)
This protocol allows a computer (or many computers on your network) to be
automatically assigned a single IP address from a DHCP server.
DNS Server Address (Domain Name System)
DNS allows Internet host computers to have a domain name and one or more IP
addresses. A DNS server keeps a database of host computers and their respective
domain names and IP addresses, so that when a user enters a domain name into
the Internet browser, the user is sent to the proper IP address. The DNS server
address used by the computers on your home network is the location of the DNS
server your ISP has assigned.
Chapter 5
Glossary
DSL Modem (Digital Subscriber Line)
A DSL modem uses your existing phone lines to transmit data at high speeds.
Direct-Sequence Spread Spectrum (for 802.11b)
Spread spectrum (broadband) uses a narrowband signal to spread the transmission
over a segment of the radio frequency band or spectrum. Direct-sequence is a
spread spectrum technique where the transmitted signal is spread over a particular
frequency range.
30
WL-130N_manual.indd 30
ASUS WLAN Adapter
4/10/07 12:30:23 PM
Chapter 5 - Glossary
Direct-sequence systems communicate by continuously transmitting a redundant
pattern of bits called a chipping sequence. Each bit of transmitted data is mapped
into chips and rearranged into a pseudorandom spreading code to form the
chipping sequence. The chipping sequence is combined with a transmitted data
stream to produce the output signal.
Wireless mobile clients receiving a direct-sequence transmission use the spreading
code to map the chips within the chipping sequence back into bits to recreate the
original data transmitted by the wireless device. Intercepting and decoding a directsequence transmission requires a predefined algorithm to associate the spreading
code used by the transmitting wireless device to the receiving wireless mobile
client.
This algorithm is established by IEEE 802.11b specifications. The bit redundancy
within the chipping sequence enables the receiving wireless mobile client to
recreate the original data pattern, even if bits in the chipping sequence are
corrupted by interference. The ratio of chips per bit is called the spreading ratio.
A high spreading ratio increases the resistance of the signal to interference. A
low spreading ratio increases the bandwidth available to the user. The wireless
device uses a constant chip rate of 11Mchips/s for all data rates, but uses different
modulation schemes to encode more bits per chip at the higher data rates. The
wireless device is capable of an 11 Mbps data transmission rate, but the coverage
area is less than a 1 or 2 Mbps wireless device since coverage area decreases as
bandwidth increases.
Encryption
This provides wireless data transmissions with a level of security. This option
allows you to specify a 64-bits or a 128-bits WEP key. A 64-bits encryption contains
10 hexadecimal digits or 5 ASCII characters. A 128-bits encryption contains 26
hexadecimal digits or 13 ASCII characters.
64-bit and 40-bit WEP keys use the same encryption method and can interoperate
on wireless networks. This lower level of WEP encryption uses a 40-bits (10
hexadecimal digits assigned by the user) secret key and a 24-bits Initialization
Vector assigned by the device. 104-bits and 128-bits WEP keys use the same
encryption method.
All wireless clients in a network must have identical WEP keys with the access
point to establish connection. Keep a record of the WEP encryption keys.
Chapter 5
Glossary
Extended Service Set (ESS)
A set of one or more interconnected basic service set (BSSs) and integrated
local area networks (LANs) can be configured as an Extended Service Set.
ESSID (Extended Service Set Identifier)
You must have the same ESSID entered into the gateway and each of its wireless
clients. The ESSID is a unique identifier for your wireless network.
ASUS WLAN Adapter
WL-130N_manual.indd 31
31
4/10/07 12:30:24 PM
Chapter 5 - Glossary
Ethernet
The most widely used LAN access method, which is defined by the IEEE 802.3
standard. Ethernet is normally a shared media LAN meaning all devices on the
network segment share total bandwidth. Ethernet networks operate at 10Mbps
using CSMA/CD to run over 10-BaseT cables.
Firewall
A firewall determines which information passes in and out of a network. NAT can
create a natural firewall by hiding a local network’s IP addresses from the Internet.
A Firewall prevents anyone outside of your network from accessing your computer
and possibly damaging or viewing your files.
Gateway
A network point that manages all the data traffic of your network, as well as to the
Internet and connects one network to another.
IEEE
The Institute of Electrical and Electronics Engineers. The IEEE sets standards
for networking, including Ethernet LANs. IEEE standards ensure interoperability
between systems of the same type.
IEEE 802.11
IEEE 802.xx is a set of specifications for LANs from the Institute of Electrical
and Electronic Engineers (IEEE). Most wired networks conform to 802.3, the
specification for CSMA/CD based Ethernet networks or 802.5, the specification for
token ring networks. 802.11 defines the standard for wireless LANs encompassing
three incompatible (non-interoperable) technologies: Frequency Hopping Spread
Spectrum (FHSS), Direct Sequence Spread Spectrum (DSSS), and Infrared.
802.11 specifies a carrier sense media access control and physical layer
specifications for 1 and 2 Mbps wireless LANs.
IEEE 802.11a (54Mbits/sec)
Chapter 5
Glossary
Compared with 802.11b: The 802.11b standard was designed to operate in
the 2.4-GHz ISM (Industrial, Scientific and Medical) band using direct-sequence
spread-spectrum technology. The 802.11a standard, on the other hand, was
designed to operate in the more recently allocated 5-GHz UNII (Unlicensed
National Information Infrastructure) band. And unlike 802.11b, the 802.11a standard
departs from the traditional spread-spectrum technology, instead using a frequency
division multiplexing scheme that's intended to be friendlier to office environments.
The 802.11a standard, which supports data rates of up to 54 Mbps, is the Fast
Ethernet analog to 802.11b, which supports data rates of up to 11 Mbps. Like
Ethernet and Fast Ethernet, 802.11b and 802.11a use an identical MAC (Media
Access Control). However, while Fast Ethernet uses the same physical-layer
encoding scheme as Ethernet (only faster), 802.11a uses an entirely different
encoding scheme, called OFDM (orthogonal frequency division multiplexing).
32
WL-130N_manual.indd 32
ASUS WLAN Adapter
4/10/07 12:30:24 PM
Chapter 5 - Glossary
The 802.11b spectrum is plagued by saturation from wireless phones, microwave
ovens and other emerging wireless technologies, such as Bluetooth. In contrast,
802.11a spectrum is relatively free of interference.
The 802.11a standard gains some of its performance from the higher frequencies
at which it operates. The laws of information theory tie frequency, radiated power
and distance together in an inverse relationship. Thus, moving up to the 5-GHz
spectrum from 2.4 GHz will lead to shorter distances, given the same radiated
power and encoding scheme.
Compared with 802.11g: 802.11a is a standard for access points and radio NICs
that is ahead of 802.11g in the market by about six months. 802.11a operates in the
5GHz frequency band with twelve separate non-overlapping channels. As a result,
you can have up to twelve access points set to different channels in the same
area without them interfering with each other. This makes access point channel
assignment much easier and significantly increases the throughput the wireless
LAN can deliver within a given area. In addition, RF interference is much less likely
because of the less-crowded 5 GHz band.
IEEE 802.11b (11Mbits/sec)
In 1997, the Institute of Electrical and Electronics Engineers (IEEE) adopted the
802.11 standard for wireless devices operating in the 2.4 GHz frequency band. This
standard includes provisions for three radio technologies: direct sequence spread
spectrum, frequency hopping spread spectrum, and infrared. Devices that comply
with the 802.11 standard operate at a data rate of either 1 or 2 Mbps.
In 1999, the IEEE created the 802.11b standard. 802.11b is essentially identical
to the 802.11 standard except 802.11b provides for data rates of up to 11 Mbps
for direct sequence spread spectrum devices. Under 802.11b, direct sequence
devices can operate at 11 Mbps, 5.5 Mbps, 2 Mbps, or 1 Mbps. This provides
interoperability with existing 802.11 direct sequence devices that operate only at 2
Mbps.
Direct sequence spread spectrum devices spread a radio signal over a range of
frequencies. The IEEE 802.11b specification allocates the 2.4 GHz frequency band
into 14 overlapping operating Channels. Each Channel corresponds to a different
set of frequencies.
IEEE 802.11g
Chapter 5
Glossary
802.11g is a new extension to 802.11b (used in majority of wireless LANs today)
that broadens 802.11b's data rates to 54 Mbps within the 2.4 GHz band using
OFDM (orthogonal frequency division multiplexing) technology. 802.11g allows
backward compatibility with 802.11b devices but only at 11 Mbps or lower,
depending on the range and presence of obstructions.
IEEE 802.11n
802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input
multiple-output). MIMO usesmultiple transmitter and receiver antikennas to allow
for increased data throughout via sspacial multiplexing and increased range by
exploiting the spacial diversity. The real data throughout is estimated to reach a
theoretical 300 Mbps, and should be up to 30 times faster than 802.11b, and up to
6 times faster than 802.11g.
ASUS WLAN Adapter
WL-130N_manual.indd 33
33
4/10/07 12:30:25 PM
Chapter 5 - Glossary
Infrastructure
A wireless network centered about an access point. In this environment, the access
point not only provides communication with the wired network but also mediates
wireless network traffic in the immediate neighborhood.
IP (Internet Protocol)
The TCP/IP standard protocol that defines the IP datagram as the unit of
information passed across an Internet and provides the basis for connectionless
packet delivery service. IP includes the ICMP control and error message protocol
as an integral part. It provides the functional equivalent of ISO OSI Network
Services.
IP Address
An IP address is a 32-bits number that identifies each sender or receiver of
information that is sent across the Internet. An IP address has two parts: the
identifier of a particular network on the Internet and an identifier of the particular
device (which can be a server or a workstation) within that network.
ISM Bands (Industrial, Scientific, and Medicine Bands)
Radio frequency bands that the Federal Communications Commission (FCC)
authorized for wireless LANs. The ISM bands are located at 902 MHz, 2.400 GHz,
and 5.7 GHz.
ISP (Internet Service Provider)
An organization that provides access to the Internet. Small ISPs provide service
via modem and ISDN while the larger ones also offer private line hookups (T1,
fractional T1, etc.).
LAN (Local Area Network)
A communications network that serves users within a defined geographical area.
The benefits include the sharing of Internet access, files and equipment like
printers and storage devices. Special network cabling (10 Base-T) is often used to
connect the PCs together.
Chapter 5
Glossary
MAC Address (Media Access Control)
A MAC address is the hardware address of a device connected to a network.
NAT (Network Address Translation)
NAT masks a local network’s group of IP addresses from the external network,
allowing a local network of computers to share a single ISP account. This process
allows all of the computers on your home network to use one IP address. This will
enable access to the Internet from any computer on your home network without
having to purchase more IP addresses from your ISP.
34
WL-130N_manual.indd 34
ASUS WLAN Adapter
4/10/07 12:30:26 PM
Chapter 5 - Glossary
NIC (Network Interface Card)
A network adapter inserted into a computer so that the computer can be connected
to a network. It is responsible for converting data from stored in the computer to the
form transmitted or received.
Packet
A basic message unit for communication across a network. A packet usually
includes routing information, data, and sometimes error detection information.
Pass Phrase
The Wireless Settings utility uses an algorithm to generate four WEP keys
based on the typed combination.
PPP (Point-to-Point Protocol)
PPP is a protocol for communication between computers using a serial interface,
typically a personal computer connected by phone line to a server.
PPPoE (Point-to-Point Protocol over Ethernet)
Point-to-Point Protocol is a method of secure data transmission. PPP using
Ethernet to connect to an ISP.
Preamble
Allows you to set the preamble mode for a network to Long, Short, or Auto. The
default preamble mode is Long.
Radio Frequency (RF) Terms: GHz, MHz, Hz
Chapter 5
Glossary
The international unit for measuring frequency is Hertz (Hz), equivalent to the
older unit of cycles per second. One megahertz (MHz) is one million Hertz. One
gigahertz (GHz) is one billion Hertz. The standard US electrical power frequency is
60 Hz, the AM broadcast radio frequency band is 0.55-1.6 MHz, the FM broadcast
radio frequency band is 88-108 MHz, and wireless 802.11 LANs operate at 2.4
GHz.
SSID (Service Set Identifier)
SSID is a group name shared by every member of a wireless network. Only client
PCs with the same SSID are allowed to establish a connection. Enabling the
Response to Broadcast SSID requests option allows the device to broadcast
its SSID in a wireless network. This allows other wireless devices to scan and
establish communication with the device. Unchecking this option hides the SSID to
prevent other wireless devices from recognizing and connecting to the device.
Station
Any device containing IEEE 802.11 wireless medium access conformity.
ASUS WLAN Adapter
WL-130N_manual.indd 35
35
4/10/07 12:30:26 PM
Chapter 5 - Glossary
Subnet Mask
A subnet mask is a set of four numbers configured like an IP address. It is used to
create IP address numbers used only within a particular network.
TCP (Transmission Control Protocol)
The standard transport level protocol that provides the full duplex, stream service
on which many application protocols depend. TCP allows a process or one
machine to send a stream of data to a process on another. Software implementing
TCP usually resides in the operating system and uses the IP to transmit information
across the network.
WAN (Wide Area Network)
A system of LANs, connected together. A network that connects computers located
in separate areas, (i.e., different buildings, cities, countries). The Internet is a wide
area network.
WECA (Wireless Ethernet Compatibility Alliance)
An industry group that certifies cross-vender interoperability and compatibility
of IEEE 802.11b wireless networking products and to promote that standard for
enterprise, small business, and home environments.
WPA (Wi-Fi Protected Access)
Wi-Fi Protected Access (WPA) is an improved security system for 802.11. It is part
of the 802.11i draft security standard. WPA encompasses TKIP (Temporal Key
Integrity Protocol) along with MIC (Message Integrity Check) and other fixes to
WEP such as Weak IV (Initialization Vector) filtering and Random IV generation.
TKIP uses 802.1x to deploy and change temporary keys as opposed to static
WEP keys once used in the past. It is a significant improvement over WEP. WPA
is part of a complete security solution. WPA also requires authentication servers in
enterprise security solutions.
Requirements
Chapter 5
Glossary
(1) A WPA compatible access point or Wireless router, (2) Operating system
updates that support WPA. In Windows ® XP, an updated Windows Zero
Configuration service is needed. Users can download the Windows® XP WPA patch
here:
h t t p : / / w w w. m i c r o s o f t . c o m / d o w n l o a d s / d e t a i l s . a s p x ? d i s p l a y l a n g = z h tw&FamilyID=2726F32F-D52B-4F84-ACE8-F7FC20195769
Please note that this patch requires the installation Windows XP Service Pack 1,
which is available here: http://www.microsoft.com/WindowsXP/pro/downloads/
servicepacks/sp1/default.asp
For earlier Windows Operating systems, a WPA capable supplicant is required
such as Funk Software’s Odyssey Client.
WLAN (Wireless Local Area Network)
This is a group of computers and other devices connected wirelessly in a small
area. A wireless network is referred to as LAN or WLAN.
36
WL-130N_manual.indd 36
ASUS WLAN Adapter
4/10/07 12:30:27 PM
Chapter 6 - Appendix
6. Appendix
FCC Warning Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
undesired operation.
may cause
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Prohibition of Co-location
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter
Chapter 6
Appendix
Safety Information
To maintain compliance with FCC’s RF exposure guidelines, this equipment
should be installed and operated with minimum distance 20cm between the
radiator and your body. Use on the supplied antenna.
ASUS WLAN Adapter
WL-130N_manual.indd 37
37
4/10/07 12:30:29 PM
Chapter 6 - Appendix
Declaration of Conformity for R&TTE directive 1999/5/EC
Essential requirements – Article 3
Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950-1 has been conducted. These
are considered relevant and sufficient.
Protection requirements for electromagnetic compatibility – Article 3.1b
Testing for electromagnetic compatibility according to EN 301 489-1 and EN
301 489-17 has been conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328- 2 has been conducted.
These are considered relevant and sufficient.
CE Mark Warning
This is a Class B product, in a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Chapter 6
Appendix
38
WL-130N_manual.indd 38
ASUS WLAN Adapter
4/10/07 12:30:30 PM