Atdec SD-DO-42-BK flat panel desk mount Specification
Add to my manuals2 Pages
Atdec SD-DO is a versatile display mount designed to enhance your viewing experience. It features a 40° angular movement VESA ball mount, allowing you to position your display for optimal comfort. The mount is compatible with both 42mm and 50mm diameter poles, providing flexible installation options. With its quick-release lever, you can effortlessly adjust the height and position of your display, making it ideal for dynamic work environments. Additionally, the SD-DO comes with a security screw to ensure your display remains securely in place, preventing accidental detachment.
advertisement
SD-DO
Installation Instructions
Display | Quickshift Donut
! The Spacedec Display Quickshift Donut is to be used on 42mm and 50mm diameter poles only.
! The Manufacturer accepts no responsibility for incorrect installation.
Component Checklist
Check you have received all parts against this Component Checklist prior to installation.
Quickshift
Donut (x1)
42mm Front
Donut Insert (x1)
Visidec Groove
Lock (x1)
42mm Rear
Donut Insert (x1)
Hardware
Security
Screw (x1)
2mm Allen
Key (x1)
5mm Allen
Key (x1)
Tightening
Tool (x1)
Mounting
Screws
M4x10mm
Screw (x4)
M4x12mm
Screw (x4)
M4x16mm
Screw (x4)
Step 1. Install Quickshift Donut
Select your correct product configuration: A, B, or C.
A. Use this configuration with a standard 50mm pole
(No inserts required)
B. Use this configuration with a
Visidec 42mm extrusion
pole
Front Donut
Insert
Groove
Insert
Rear Donut
Insert
C. Use this configuration with a
standard 42mm pole
Front Donut
Insert
Rear Donut
Insert
OR OR
Note: Ensure inserts are fitted in correct orientation.
Slide the Quickshift Donut onto the pole
(with the lever open), removing the End
Cap if necessary.
Rear groove insert must align with slot in the Pole.
Arrows point to top surface
Slide the Quickshift Donut into the desired position.
If necessary, adjust the tension between the
Quickshift Donut and the Pole using the 5mm Allen
Key supplied.
Once in place, close the lever to lock the Quickshift Donut in the desired position.
Groove
Insert
Slot
TIGHTEN
(Visidec 42mm pole shown)
LOOSEN
WARNING: Be careful not to overtighten
CLOSE
Step 2. Remove VESA plate from Quickshift Donut
Press and hold the Release Buttons (one on either side).
Whilst holding the Release Buttons, remove the VESA Plate.
VESA Plate
LIFT
Release
Button
Release
Buttons
Step 3. Attach the VESA plate to your Display
There are two mounting hole configurations:
UÊÇxÊÝÊÇx
UÊ£ääÊÝÊ£ää
Choose appropriate Mounting Screws from the Hardware supplied to suit your Display.
Top of
Display
Çx
100mm
(3”)
(4”)
Step 4. Attach your Display to the Quickshift Donut
Hook the top of the VESA plate onto the Quickshift Mount.
Gently push the bottom of the Display into the Mount until it ‘CLICKS’.
VESA plate
Çx
Mounting Screws (x4)
VESA Plate
(3”) 100mm
(4”)
Back of Display
Insert the Security Screw, and tighten using the 2mm Allen Key.
TIGHTEN
Back of Display
Step 5. Adjusting the VESA Ball Mount
Position your Display to the desired viewing angle, using the 40° angular movement allowed by the VESA Ball Mount.
Depending on the weight of the display, it may be necessary to make adjustments to the VESA Ball Mount. If the display does not hold its position, or is too resistant, adjust the Tension Plate located at the rear of the VESA Ball Mount (see diagram right).
CLICK
To make any adjustments, use the Tightening Tool supplied.
Check the display, and then adjust again if necessary.
Installation Complete
Tightening
Tool
Tension
Plate
Loosen (-Kg)
Tighten (+Kg)
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 18.05.09 ©
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project